মাইক্রোকন্ট্রোলার

পণ্য (20,000+)

PIC12F508-I/SN - 8-bit 4MHz MCU 768B Flash 8-SOIC | Microchip
PIC12F508-I/SN

PIC12F508-I/SN - 8-bit 4MHz MCU 768B Flash 8-SOIC | Microchip

The Microchip Technology PIC12F508-I/SN is an 8-bit RISC Flash microcontroller from the PIC12 family running at up to 4MHz instruction rate, with 768 bytes (512 x 12 words) of Flash program memory, 25 bytes of RAM, and 6 general-purpose I/O pins, packaged in an 8-pin SOIC (SN) with industrial -40C to +85C operating range. It features a 12-bit-wide instruction set that yields typical 2:1 code compression over comparable 8-bit microcontrollers, reducing Flash footprint and lowering per-unit BOM cost in high-volume designs. A microcontroller (MCU) is a single-chip computer integrating a CPU core, program memory (Flash/ROM), data memory (RAM), peripherals, and I/O on one die. The PIC12F508 belongs to the baseline PIC10/12/16 family - a subcategory of 8-bit microcontrollers optimized for low pin-count, low-cost, deterministic control tasks where an M-class ARM Cortex-M0 part would be overkill. Within the embedded hierarchy it sits between simple logic ICs (timers, gate drivers) and higher-end 32-bit MCUs, often replacing discrete logic plus a small EEPROM in space-constrained assemblies. Key features of this part include an internal 4MHz RC oscillator (no external crystal required), one 8-bit Timer0 with programmable prescaler, a watchdog timer with on-chip RC oscillator for reliable reset, in-circuit serial programming (ICSP) via GP0/GP1, and on-chip in-circuit emulation support. The wide VDD range of 2.0V to 5.5V allows direct operation from 2xAA cells, single-cell Li-ion, or 3.3V/5V regulated rails. Six I/O pins each source/sink up to 25 mA, sufficient to drive LEDs, small relays, and logic buffers directly without external transistors. The PIC12F508 architecture uses a Harvard RISC core with a single accumulator (W register) and 32-byte file-register SRAM, executing most instructions in a single 1us instruction cycle at 4MHz. The 12-bit instruction word eliminates unused upper bits, simplifying decoder logic and keeping silicon area minimal, which is why baseline PICs are consistently priced below 8-bit competitors. Brown-out detect and power-on reset are integrated. Typical applications include low-cost consumer appliance controls, LED blinkers and decorative lighting drivers, PIR motion-sensor trigger boards, simple PWM fan or buzzer controllers, replacement of 555-timer + logic-gate circuits, and battery-powered remote keyfob transmitters. Its tiny 8-SOIC footprint and sub-$0.50 price point make it a go-to MCU for sub-100-node production runs. Design tip: use GP0/GP1 for ICSP - reserve these two pins even in production PCB layouts so the firmware can be re-flashed without rework. Add a 100nF decoupling cap directly across VDD/VSS (pin 1 and pin 8), keep traces short, and route MCLR with its pull-up within 25 mm of pin 4 to avoid spurious resets in noisy environments. This page synthesizes distributor pricing snapshots, verified drop-in alternatives in the same 8-SOIC package, and engineering design notes not found in the standalone datasheet - giving procurement and design engineers an at-a-glance view of supply, fit, and form.

RFQ যোগাযোগ
PIC12F508T-E/SN - 8-bit Flash MCU, 4MHz, 768B Flash, 8-SOIC | Microchip
PIC12F508T-E/SN

PIC12F508T-E/SN - 8-bit Flash MCU, 4MHz, 768B Flash, 8-SOIC | Microchip

The Microchip Technology PIC12F508T-E/SN is an 8-bit, fully-static, Flash-based CMOS microcontroller in an 8-pin SOIC package with 4 MHz internal oscillator, 768 bytes of Flash program memory (512 x 12 words), 25 bytes of RAM, and 6 general-purpose I/O pins. It belongs to Microchip's PIC12 baseline core family with 33 single-word/single-cycle instructions and a 12-bit wide instruction word, achieving typical 2:1 code compression versus competing 8-bit MCUs in the same price tier. What is a baseline PIC microcontroller? A baseline PIC microcontroller (PIC10/12 family) is an 8-bit RISC MCU using a Harvard architecture with separate program and data buses and a 2-level deep hardware stack. It executes one instruction per oscillator cycle (200 ns at 20 MHz, 1 µs at 4 MHz internal oscillator) and is positioned at the entry-level of Microchip's 8-bit portfolio, optimized for cost-sensitive and pin-constrained applications such as consumer appliances, toys, sensor signal conditioning, and simple logic replacement. Key features include one 8-bit timer (TMR0), a Watchdog Timer (WDT) with on-chip RC oscillator, In-Circuit Serial Programming (ICSP), In-Circuit Debugging, 25 mA source/sink per I/O pin, ultra-low 100 nA sleep current, and an extended operating temperature range of -40 °C to +125 °C. The internal 4 MHz precision oscillator eliminates the need for an external crystal, reducing BOM cost and PCB area. Architecturally, the PIC12F508 uses a 14-bit instruction word (12 bits used for opcode plus data), 8-bit data path, and 2-level stack. The Harvard architecture allows instruction fetch and data access to occur in the same cycle, giving deterministic 1 MIPS performance at 4 MHz. The Flash memory supports in-system programming via ICSP, enabling firmware updates in the field without removing the device. Typical applications include consumer electronics (remote controls, toys, small appliances), automotive body electronics (interior lighting, simple sensor interfaces), industrial control (timers, sequencers, logic replacement), IoT edge nodes (battery-powered sensor readouts), and home appliances (white goods user interfaces). The 100 nA sleep current makes it well-suited to battery-backed or energy-harvesting designs. When designing with the PIC12F508, note that the device operates from 2.0 V to 5.5 V and is qualified to the -E (Extended) temperature grade. The T-suffix indicates Tape-and-Reel packaging for high-volume assembly. For new designs, Microchip recommends the PIC16F15313 as the modern migration path with enhanced peripherals and lower power. This page synthesizes distributor stock and pricing, drop-in same-package alternatives, application notes, and design considerations not consolidated in a single location in the manufacturer datasheet.

RFQ যোগাযোগ
PIC12F509-E/MC - 8-bit Flash MCU, 4MHz, 1.5KB | Microchip
PIC12F509-E/MC

PIC12F509-E/MC - 8-bit Flash MCU, 4MHz, 1.5KB | Microchip

The Microchip Technology PIC12F509-E/MC is an 8-bit Flash-based CMOS microcontroller from the PIC12 family, featuring a 4 MHz internal oscillator, 1.5 KB (1K x 12) of Flash program memory, and 41 bytes of RAM, housed in an 8-pin DFN (2x3 mm) exposed-pad package. The -E suffix denotes the Extended operating temperature range of -40C to +125C, suitable for industrial and automotive under-hood environments. What is an 8-bit Flash Microcontroller (MCU)? An 8-bit Flash MCU is a single-chip computer built around an 8-bit data path with non-volatile Flash program memory. The PIC12F509 family uses Microchip's RISC architecture with 33 single-word single-cycle instructions, providing typically 2:1 code compression over competitive 8-bit MCUs and execution times that are 4x faster per instruction than legacy CISC designs. Key features include six general-purpose I/O pins, an internal 4 MHz RC oscillator, 12-bit-wide instruction words, a wide operating voltage range of 2.0V to 5.5V, and on-chip in-circuit serial programming (ICSP) that allows the device to be programmed after PCB assembly. The PIC12F509 also includes a hardware 8-bit timer with watchdog, power-on reset, brown-out detect, and code protection. With only 8 pins total, it is among the smallest packaged PIC microcontrollers available and is a strong fit for cost- and space-constrained applications. Architecture depth: the PIC12F509 uses a Harvard bus architecture with separate program and data paths, plus a 2-stage pipeline that overlaps fetch and execute to deliver 1 MIPS performance at 4 MHz. The 12-bit instruction word delivers richer opcode space than 8-bit CISC alternatives and produces more compact code, allowing 1.5 KB of Flash to deliver functionality that often requires 2-3 KB on competing cores. Brown-out detect and a configurable watchdog timer enable robust unattended operation. Typical applications include low-cost consumer appliances, battery-powered remote sensors, LED lighting controllers, simple fan/thermostat controls, and automotive body electronics (e.g., seat heater controllers, lighting blinkers). The wide 2-5.5V supply range also makes it well suited to single-cell lithium or 2xAA battery products. When designing with this device, remember that the DFN exposed pad MUST be soldered to the PCB ground plane for thermal and electrical performance. For prototyping, the same silicon is also offered in 8-pin PDIP and 8-pin SOIC packages, which are easier to breadboard.

RFQ যোগাযোগ
PIC12F509-E/MS - 8-Bit 4MHz MCU 1.5KB Flash MSOP-8 | Microchip
PIC12F509-E/MS

PIC12F509-E/MS - 8-Bit 4MHz MCU 1.5KB Flash MSOP-8 | Microchip

The Microchip Technology PIC12F509-E/MS is an 8-bit RISC Flash microcontroller featuring a 4 MHz internal oscillator, 1.5 KB (1K x 12 words) of program Flash memory and 41 bytes of data RAM, housed in an 8-pin MSOP package. The device operates from 2.0 V to 5.5 V and is rated for the extended industrial temperature range of -40 °C to +125 °C. An 8-bit microcontroller (MCU) is a single-chip computer built around an 8-bit data path, integrating a CPU, program memory, data RAM, and configurable I/O peripherals on one die. Within the broader taxonomy, the PIC12F509 belongs to the Microchip PIC12 baseline family -> PIC microcontroller -> 8-bit MCU -> microcontroller -> embedded processor -> semiconductor. Baseline PIC12 devices use a RISC architecture with 33 single-word single-cycle instructions, delivering predictable 200 ns instruction execution at 20 MHz (or 1 µs at 4 MHz internal oscillator) and ~2:1 code density over competitive 8-bit MCUs. Microchip recommends the PIC16F15313 as a newer migration device. Key features include 6 general-purpose digital I/O pins, four oscillator selections (EXTRC, INTRC, XT, LP), a watchdog timer with on-chip RC oscillator, in-circuit serial programming (ICSP), and code protection. The device has 1024 words (1.5 KB) of self-programmable Flash, 41 bytes of SRAM, and an 8-bit timer/counter (TMR0) with 8-bit prescaler. Power-on reset (POR) and device reset timer (DRT) eliminate the need for external reset circuitry. Typical applications include low-cost consumer appliances, automotive subsystems (sensor interfaces, LED drivers, fans), industrial control logic, battery-powered devices, and remote controls. The 6 I/O pins drive LEDs, read switches, and interface to peripherals such as comparators or external EEPROMs. When designing with this part, place a 0.1 µF decoupling capacitor adjacent to VDD, observe the in-circuit serial programming (ICSP) pinout (GP1/ICSPCLK, GP0/ICSPDAT, GP3/MCLR̄/VPP), and verify that the chosen oscillator configuration matches the application's timing tolerance. The -E suffix denotes the extended -40 °C to +125 °C operating range. This page consolidates distributor pricing, drop-in same-package alternatives, and practical design notes not aggregated on the manufacturer datasheet alone.

RFQ যোগাযোগ
PIC12F509-E/P - 4MHz 8-Bit Flash MCU | Microchip
PIC12F509-E/P

PIC12F509-E/P - 4MHz 8-Bit Flash MCU | Microchip

The Microchip Technology PIC12F509-E/P is an 8-bit flash-programmable microcontroller with a 4 MHz internal oscillator, 2 KB of program memory, 41 bytes of RAM, and 6 general-purpose I/O pins, housed in an 8-pin through-hole package. It combines a baseline PIC core using 12-bit-wide instructions with 33 instructions and a two-level hardware stack. The MCU operates from 2 V to 3 V and is identified by Microchip as an in-production family, although the manufacturer recommends PIC16F15313 as a newer device for new designs. An 8-bit microcontroller is a compact embedded-control semiconductor that executes firmware from embedded program memory and reads inputs from sensors, switches, and communication peripherals. The PIC12F509 belongs to the PIC12 family of baseline 8-bit devices, a subcategory of microcontrollers within the broader integrated-circuit and embedded-processing hierarchy. Its small program memory, limited RAM, and compact pin count suit simple control tasks rather than demanding networking, graphics, or high-speed signal processing. The PIC12F509-E/P provides 2 KB of flash memory, 41 bytes of RAM, 6 I/O pins, and a maximum clock speed of 4 MHz. Its 12-bit instruction word permits efficient encoding of common operations, while most instructions complete in a single cycle and program branches require two cycles. The baseline core includes 33 instructions and a two-level stack, making software structure and interrupt depth important considerations in compact control firmware. The extended-temperature ordering code identifies the E grade, which is intended for operation across a wider temperature range than the industrial I grade. The P package suffix denotes the lead-free plastic through-hole format associated with this ordering code. Exact operating-temperature limits, electrical maximums, configuration-bit details, and package dimensions were not included in the verified search data and must therefore be confirmed in the manufacturer datasheet before release to production. Typical uses include small standalone controllers, relay and output logic, sensor-conditioned switching, lamp or indicator control, and low-speed embedded automation modules. The six I/O pins support a compact peripheral arrangement, while 2 KB of flash can hold a focused control routine rather than a large application framework. For designs requiring more memory, more I/O, or modern peripheral options, engineers should evaluate the manufacturer-recommended PIC16F15313 instead. The principal design consideration is to confirm the complete pinout, programming configuration, electrical limits, and decoupling requirements against the official PIC12F509 datasheet. The 2 V to 3 V supply range also requires attention to regulator tolerance, startup behavior, and the voltage levels of attached peripherals. Because no verified distributor price or exact stock quantity was supplied, purchasing should be based on a current quote rather than an assumed unit price. This product page consolidates the verified Microchip product status, distributor specifications, packaging indication, architecture details, and available replacement information. It also distinguishes genuine package-compatible options from related devices that require different footprints, firmware, or design verification, adding procurement and engineering context beyond a basic manufacturer specification listing.

RFQ যোগাযোগ
PIC12F509-E/SN - 8-bit MCU, 1.5KB Flash, 4MHz, 8-SOIC | Microchip
PIC12F509-E/SN

PIC12F509-E/SN - 8-bit MCU, 1.5KB Flash, 4MHz, 8-SOIC | Microchip

The Microchip Technology PIC12F509-E/SN is an 8-bit PIC microcontroller based on a 12-bit instruction word architecture, featuring 1.5KB (1K x 12) of Flash program memory, 41 bytes of RAM, and 6 I/O pins in an 8-pin SOIC package. It executes instructions at up to 4 MHz from an internal 4 MHz RC oscillator, providing an economical solution for simple control tasks. The integrated Flash memory supports in-circuit serial programming (ICSP) for field updates, and the wide 2.0V to 5.5V operating range lets the same part run from two AA cells, a 3.3V regulated rail, or a 5V logic supply. What is an 8-bit microcontroller? An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, non-volatile program memory (ROM/Flash), volatile data memory (RAM), and peripherals (I/O, timers, ADC, communications) on one die. Within the broader taxonomy, the PIC12F509 belongs to the PIC10/12 baseline family of microcontrollers -> 8-bit MCU -> microcontroller -> embedded processor -> semiconductor. It targets cost-sensitive and pin-constrained designs where a full 28- or 40-pin MCU would be wasteful. Key features of the PIC12F509-E/SN include six general-purpose digital I/O pins (each capable of independent direction control), one 8-bit timer/counter (TMR0) with a programmable prescaler, a watchdog timer with its own on-chip RC oscillator for reliable reset behavior, and an internal 4 MHz oscillator that eliminates the need for an external crystal. Power-on reset, brown-out detect, and code protection round out the integrated feature set, all in a 150-mil wide 8-SOIC footprint that reflow-solders with standard lead-free profiles. The device uses a RISC-like architecture with only 33 single-word/12-bit instructions, so the MCU typically achieves a 2:1 code compression over comparable 8-bit CISC competitors. CMOS process technology provides low power consumption, with sleep currents in the microamp range and operating currents typically below 1 mA at 4 MHz/5V, making the part attractive for battery-powered applications. Typical applications include consumer electronics remote controls, battery chargers, LED drivers, small appliance controllers, sensor signal conditioning, and hobby/educational projects. The PIC12F509-E/SN is also widely used as a low-cost "glue logic" replacement where a handful of discrete components can be replaced by programmable logic. When designing with this MCU, allocate one or two I/O pins for ICSP (ICSPCLK/ICSPDAT) if you plan to re-program in-circuit. Use the configuration bits to select the oscillator mode, watchdog enable, and code protection; these fuses are programmed once and govern the device's behavior at every reset. The -E (extended) temperature grade supports -40C to +125C operation, broader than the -I (industrial) -40C to +85C grade. This page synthesizes distributor pricing, drop-in package alternatives, and practical design notes that are not found in the standalone manufacturer datasheet.

RFQ যোগাযোগ
PIC12F509-I/MC - 8-bit MCU, 1.5KB Flash, 4MHz INTOSC, 8-DFN | Microchip
PIC12F509-I/MC

PIC12F509-I/MC - 8-bit MCU, 1.5KB Flash, 4MHz INTOSC, 8-DFN | Microchip

The Microchip Technology PIC12F509-I/MC is a low-cost, high-performance 8-bit CMOS Flash microcontroller in an 8-pin DFN (2x3 mm) package, featuring 1.5KB (1K x 12) of Flash program memory, 41 bytes of RAM, and a 4 MHz internal oscillator. Operating from 2.0V to 5.5V across -40C to +85C industrial temperature range, it delivers RISC performance with only 33 single-word single-cycle instructions to learn. An 8-bit microcontroller (MCU) is a small, self-contained computer-on-a-chip built around an 8-bit data path, integrating a CPU, program memory (ROM/Flash), data memory (RAM), and peripherals such as timers, ADC, and GPIO into a single IC. 8-bit MCUs sit within the microcontroller hierarchy as embedded controllers -> microcontrollers -> microcomputer family -> integrated circuits -> semiconductors, occupying the low-cost, low-power end of the MCU spectrum versus 16-bit and 32-bit alternatives. They are best suited for cost-sensitive applications where software complexity and processing throughput remain modest. Key features of the PIC12F509 include 33 single-word instructions at 1 microsecond instruction cycle, an internal 4 MHz oscillator with 6 I/O pins (5 bidirectional, 1 input-only), a Watchdog Timer with on-chip RC oscillator for reliable operation, and In-Circuit Serial Programming (ICSP) for field-upgradeable firmware. The device supports power-managed modes including Sleep and wake-on-pin-change for ultra-low standby power consumption. The PIC12F509 architecture uses a Harvard RISC core with separate program and data buses, a 12-bit wide instruction word, and a hardware stack that simplifies subroutine handling. Its 6 I/O pins include GP0-GP5 with multi-function capability (digital I/O, comparator input, timer I/O), one 8-bit timer/counter (TMR0) with 8-bit prescaler, and an integrated analog comparator. With 1.5KB Flash, it targets code sizes up to roughly 1000 instructions typical. Typical applications include battery-powered consumer products, LED drivers, simple motor control, sensor signal conditioning, and any small-form-factor embedded control where the 8-DFN footprint saves board space. The 8-pin DFN package makes it ideal for ultra-compact designs including wearables, IoT edge nodes, and smart sensors. When designing with the PIC12F509, note that only 5 of 6 I/O pins are fully bidirectional; GP3 is input-only. For applications requiring more I/O, consider PIC16F15313 (recommended upgrade). The internal 4 MHz oscillator can drift with temperature - for precision timing use an external crystal or the PIC12F1840 variant. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone, providing the engineering context needed for sourcing and board-level design decisions.

RFQ যোগাযোগ
PIC12F509-I/MS - 8-Bit MCU, 1.5KB Flash, 4MHz, 8-MSOP | Microchip
PIC12F509-I/MS

PIC12F509-I/MS - 8-Bit MCU, 1.5KB Flash, 4MHz, 8-MSOP | Microchip

The Microchip Technology PIC12F509-I/MS is an 8-bit, fully-static, Flash-based CMOS microcontroller from the PIC® 12F family, delivering 4 MIPS performance from a 33-instruction RISC core with 1.5KB (1K x 12) of program memory and 41 bytes of RAM, packaged in an 8-pin MSOP. Operating from 2.0V to 5.5V, it integrates a 4MHz internal oscillator, 6 I/O pins, a 4-channel 8-bit ADC, and one 8-bit timer/counter. What is a microcontroller? A microcontroller (MCU) is a single-chip computer that integrates a CPU, memory (Flash for program storage, SRAM for data, EEPROM for non-volatile data), peripherals (ADC, timers, communication interfaces), and clock management on one die. MCUs form the "brain" of embedded systems - they sit in the device hierarchy between discrete logic ICs and full microprocessors (MPUs). Within Microchip's portfolio, PIC® microcontrollers span 8-bit (PIC10/12/16/18), 16-bit (dsPIC®/PIC24), and 32-bit (PIC32) architectures. The PIC12F family targets the lowest-cost, lowest-pin-count applications with 6-8 I/O, making it the PIC® equivalent of an 8-pin glue-logic replacement. Key features of the PIC12F509 include in-circuit serial programming (ICSP™), a watchdog timer with on-chip RC oscillator, power-on reset, brown-out detect, and an internal 4MHz precision oscillator that eliminates the need for an external crystal in most designs. The Flash memory supports 100,000 erase/write cycles typical and 40-year data retention, while the device consumes less than 1 mA active at 4MHz/5V. Architecturally, the PIC12F509 employs a Harvard RISC architecture with separate program and data buses, 12-bit-wide instruction words, and a two-stage pipeline that executes most instructions in a single cycle. The RISC core provides deterministic interrupt latency and predictable execution timing, while the integrated peripherals are mapped into a unified I/O space accessible through special-function registers (SFRs). Typical applications include low-cost consumer appliances, battery-powered sensor nodes, LED lighting controllers, simple motor control loops, and pin-compatible upgrades for legacy PIC12C508/PIC12C509 designs. The 8-pin MSOP footprint offers a compact form factor for space-constrained designs. When designing with the PIC12F509, ensure the ICSP™ programming pins (GP0/GP1) are accessible via test points or a programming header. The internal 4MHz oscillator is factory calibrated to ±1% typical at 5V/25°C but drifts with temperature and voltage - critical timing applications may require an external crystal via the PIC12F609/PIC12F615 family instead.

RFQ যোগাযোগ
PIC12F509-I/P - 8-Bit 4MHz 1.5KB Flash MCU | Microchip 8-PDIP
PIC12F509-I/P

PIC12F509-I/P - 8-Bit 4MHz 1.5KB Flash MCU | Microchip 8-PDIP

The Microchip Technology PIC12F509-I/P is an 8-bit Flash-based CMOS microcontroller from the PIC® 12F family, offering 1.5KB (1K x 12) of program memory and operating at up to 4MHz internal oscillator, all housed in a through-hole 8-pin PDIP (0.300 inch, 7.62mm) package. Per the Microchip datasheet, the device features 41 bytes of RAM, 6 I/O pins, an 8-bit timer/counter, and an integrated 4MHz RC oscillator. A microcontroller (MCU) is a single-chip computer containing a processor core, memory, and programmable I/O peripherals. Within the embedded semiconductor hierarchy, the PIC12F509 sits as an 8-bit Flash MCU under Microchip's PIC® 12F sub-family of baseline microcontrollers, suitable for simple control tasks. It uses a RISC architecture with only 33 single-word/single-cycle instructions, simplifying code development while maintaining deterministic execution. Key features include 1.5KB of self-programmable Flash program memory, an internal 4MHz precision oscillator (no external crystal required), 6 general-purpose digital I/O pins with individual direction control, 41 bytes of RAM, and 64 bytes of non-volatile EEPROM data memory. The device operates over an industrial -40C to +85C temperature range and supports in-circuit serial programming (ICSP) via the GP0/GP1 pins, allowing firmware updates after PCB assembly. The PIC12F509 employs a Harvard architecture with separate program and data buses, a 14-bit instruction word, and a two-stage pipeline that fetches and executes instructions in a single clock cycle (except for branches). This compact architecture yields typical 2:1 code compression over competing 8-bit MCUs in its class and predictable interrupt latency, which simplifies real-time firmware design. Typical applications include low-cost consumer appliances, battery-powered sensor nodes, LED driver controllers, simple motor control (small DC fans, solenoids), and hobby/educational projects. The wide operating voltage of 2.0V to 5.5V makes it ideal for 3V coin-cell and 2xAA battery systems where low component count is critical. When designing with this device, allocate the GP3 pin carefully because it is input-only (no output driver). Use a 0.1uF decoupling capacitor within 5mm of the VDD pin, and place a 10kohm pull-up on the MCLR pin unless the internal MCLR feature is enabled in the configuration word. This page synthesizes real-time distributor pricing, drop-in same-package alternatives, AEO-optimized FAQs, and PCB-level design notes not found in a single manufacturer datasheet view.

RFQ যোগাযোগ
PIC12F509-I/SN - 8-Bit 4MHz MCU, 1.5KB Flash | Microchip
PIC12F509-I/SN

PIC12F509-I/SN - 8-Bit 4MHz MCU, 1.5KB Flash | Microchip

The Microchip Technology PIC12F509-I/SN is an 8-bit Flash microcontroller based on the PIC12 core, delivering 4 MIPS performance at 4 MHz from a 33-instruction RISC instruction set. It integrates 1.5 KB (1K x 12 words) of Flash program memory, 41 bytes of RAM, and 41 bytes of EEPROM-style data EEPROM in an 8-pin SOIC (SN) package, providing one of the smallest pin-count footprints in the PIC10/12 family. A microcontroller (MCU) is a single-chip computer that integrates a CPU, non-volatile program memory (Flash/ROM), working RAM, and configurable I/O peripherals. The PIC12F509 belongs to the 8-bit PIC10/12 baseline/enhanced mid-range hierarchy, sitting between the even smaller 6/8-pin PIC10F family and the 14/20-pin PIC16F family. Its 8-bit Harvard architecture with separate program and data buses allows single-cycle instruction execution, and its 12-bit wide instruction word delivers the typical 2:1 code compression over competitive 8-bit MCUs of its class. Key features include an internal 4 MHz RC oscillator with calibrated accuracy of typically ±1%, six general-purpose digital I/O pins (one input-only GP3), one 8-bit timer/counter (Timer0), a watchdog timer with its own on-chip RC oscillator for reliable operation, and an in-circuit serial programming (ICSP) interface. The device supports a wide 2.0V to 5.5V operating voltage range and the industrial -40C to +85C temperature range, making it suitable for both battery-powered consumer products and harsh-environment embedded nodes. The PIC12F509's power-on reset, brown-out detect, and code-protection features are all integrated on-chip, eliminating external reset supervisors. Its ultra-low power architecture typically draws less than 1 mA active at 4 MHz / 5V and only microamperes in sleep, qualifying it for energy-harvesting and always-on sensor applications. Typical applications include battery-powered timer/sequencer modules, LED blinkers, replacement of discrete logic gates with software, simple sensor signal conditioning, low-end consumer appliances, and IoT edge-node controllers. The 8-pin SOIC footprint makes hand-soldering and breadboarding straightforward for hobbyists and rapid prototyping. When designing with this part, allocate one I/O pin to MCLR (reset) if you need external reset, or leave it tied to VDD through a resistor for the internal reset configuration. The ICSP pins (GP1/GP0) are shared with GPIO, so plan your pinout to keep PGD/PGC available during in-circuit programming. This page synthesizes distributor stock levels, drop-in SOIC-8 alternatives, and practical design notes not consolidated in the manufacturer datasheet alone, giving procurement and embedded engineers a single reference for evaluation, replacement, and board bring-up.

RFQ যোগাযোগ
PIC12F509T-I/MC - 8-bit MCU, 1.5KB Flash, 4MHz, 6 I/O | Microchip
PIC12F509T-I/MC

PIC12F509T-I/MC - 8-bit MCU, 1.5KB Flash, 4MHz, 6 I/O | Microchip

The Microchip Technology PIC12F509T-I/MC is an 8-bit, fully-static, Flash-based CMOS PIC microcontroller housed in an 8-pin DFN (3x2 mm) exposed-pad package, rated for -40C to +85C industrial operation. It delivers 4MHz CPU clock performance with 1.5KB (1K x 12) of Flash program memory, 41 bytes of RAM, and 6 general-purpose I/O pins, drawing as little as a few hundred microamps active. The 'T' suffix indicates Tape & Reel packaging, the 'I' indicates the industrial temperature range, and the 'MC' suffix indicates the DFN-8 (3x2 mm) plastic lead-free package. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory, working RAM, and peripheral I/O into one package, enabling compact, deterministic control logic. The PIC12F509 belongs to the 8-bit PIC12F family, a lineage of low-cost, high-performance, RISC-based microcontrollers from Microchip used for cost-sensitive embedded control. Within the broader taxonomy, PIC12F509 sits in this hierarchy: microcontroller -> embedded controller -> semiconductor IC. The '509 is the larger-memory sibling of the '508, both targeting applications that need more code space than a basic 8-pin MCU typically provides. Key features include 33 single-word, single-cycle RISC instructions, an 8-bit timer/counter, a watchdog timer with on-chip RC oscillator, and an internal 4MHz RC oscillator that eliminates the need for an external crystal in many designs. It operates from 2.0V to 5.5V and includes an 8-bit ADC-less architecture optimized for simple digital I/O control. The 6 I/O pins can each source/sink up to 25 mA, enabling direct LED or transistor drive. Architecturally, the PIC12F509 uses a Harvard-style RISC core with a 12-bit wide instruction word, achieving 2:1 typical code compression versus competitive 8-bit MCUs. It supports in-circuit serial programming (ICSP) via two pins, allowing firmware updates without removing the device from the board. The on-chip 4MHz RC oscillator provides +/-1% accuracy over voltage and temperature, sufficient for UART-less or low-speed timing applications. Typical applications include appliance control, LED lighting drivers, simple sensor interfaces, remote controls, battery-powered toys, and general-purpose logic replacement. The wide 2.0V to 5.5V operating range also suits 3V coin-cell designs. When designing, remember that the DFN-8 has an exposed thermal pad that MUST be soldered to the PCB ground plane for mechanical reliability and thermal dissipation. Decoupling capacitors (100 nF + 10 uF) should be placed within 3 mm of the VDD pin, and the MCLR pin must be pulled high with a 10 kohm resistor unless the reset function is intentionally disabled. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes not aggregated on the manufacturer datasheet.

RFQ যোগাযোগ
PIC12F509T-I/MS - 8-bit MCU 1.5KB Flash 6 I/O MSOP-8 | Microchip
PIC12F509T-I/MS

PIC12F509T-I/MS - 8-bit MCU 1.5KB Flash 6 I/O MSOP-8 | Microchip

The Microchip Technology PIC12F509T-I/MS is an 8-bit PIC® RISC flash microcontroller in an 8-pin MSOP package, delivering 1.5KB of program memory, 41 bytes of RAM, and 6 I/O pins. It runs at up to 4 MHz instruction rate from a 2.0 V to 5.5 V supply and is rated for the industrial temperature range (-40°C to +85°C). A baseline PIC12 microcontroller (MCU) is a small 8-bit flash-programmable controller built on Microchip's RISC architecture. MCUs sit in the device hierarchy below microprocessors; the PIC12 family is the entry-level 8-bit line optimized for cost-sensitive, low-pin-count embedded applications, while the broader PIC® family extends into 16-bit and DSC parts. The PIC12F509 specifically is a flash-based successor to the original 12C508/509 OTP family, giving users reprogrammable code memory in the same 8-pin footprint. Key features of the PIC12F509T-I/MS include a 4 MHz internal oscillator with 1% accuracy (factory calibrated), a 41-byte general-purpose RAM, an 8-level hardware stack, a watchdog timer with on-chip low-power oscillator, and a precision 4 MHz LFINTOSC. The device integrates brown-out reset, power-on reset, and an in-circuit serial programming (ICSP) interface, allowing firmware updates without removing the part from the board. The "T" suffix denotes Tape & Reel packaging for high-volume assembly. Architecturally, the PIC12F509 uses a 12-bit instruction word with single-cycle execution except for branches, delivering typical 2:1 code compression over comparable 8-bit controllers. Its Harvard architecture separates program and data paths, and the 33 single-word instructions simplify firmware development in MPLAB® X IDE and the MPASM/XC8 toolchain. Typical applications include low-cost consumer appliances, LED lighting controllers, battery chargers, sensor interfaces, and simple standby controllers in industrial equipment. With only six usable I/O, the part fits tightly-constrained boards where a full 14- or 20-pin MCU would be overkill. When designing with this part, ensure the GP3 pin is configured carefully because it is the only open-drain input shared with the MCLR/VPP function. Place a 100 nF decoupling capacitor adjacent to VDD, and connect VSS directly to a low-impedance ground plane to minimize EMI on the internal oscillator. This page synthesizes Microchip datasheet parameters, distributor pricing tiers, drop-in alternatives drawn from the PIC12 baseline family, and practical design notes not aggregated elsewhere on XAIPART.

RFQ যোগাযোগ
PIC12F510-E/MC - 8-Bit 8MHz MCU 1.5KB Flash 8-DFN | Microchip
PIC12F510-E/MC

PIC12F510-E/MC - 8-Bit 8MHz MCU 1.5KB Flash 8-DFN | Microchip

The Microchip Technology PIC12F510-E/MC is an 8-bit PIC12-family RISC microcontroller with 1.5KB (1K x 12) of Flash program memory, 41 bytes of RAM, and 6 I/O pins, housed in an 8-pin DFN (2x3 mm) package. It operates from 2.0V to 5.5V supply, supports 8 MHz internal oscillator, and integrates 4 channels of 8-bit ADC plus on-chip comparator and timer peripherals. According to the Microchip PIC12F510 datasheet, the device targets cost-sensitive 8/14-pin Flash MCU applications. A microcontroller (MCU) is a single-chip computer containing a CPU core, program memory (Flash/ROM), data memory (RAM), and integrated peripherals such as ADC, timers, and communication interfaces. The PIC12F510 belongs to the 8-bit PIC12 family, itself a subfamily of Microchip's broader PIC microcontroller portfolio, positioned for ultra-low-cost, small-pin-count embedded control. Its 8-pin DFN footprint makes it one of the smallest PIC MCUs available, suitable for space-constrained designs. Key features of the PIC12F510-E/MC include 1.5KB Flash program memory (1K x 12 words), 41 bytes SRAM, 6 general-purpose I/O pins shared with peripherals, an internal 8 MHz oscillator, and 4-channel 8-bit ADC. The integrated comparator and 8-bit/16-bit timer modules allow direct sensor interfacing and PWM generation without external components. The 'E' suffix indicates the -40C to +125C extended temperature range, and the 'MC' suffix denotes the 8-pin DFN package. The PIC12F510 uses Microchip's enhanced mid-range 8-bit RISC core with a 14-bit instruction word, 2-stage pipeline, and 33 single-word instructions. Its Harvard architecture separates program and data buses, enabling simultaneous instruction fetch and data access. The 8 MHz internal oscillator provides a 2 MIPS instruction throughput (1 MIPS at 4 MHz), and the integrated POR, BOR, and WDT improve system robustness in noisy industrial environments. Typical applications include low-cost sensor interfaces, LED driver controllers, battery chargers, simple motor controls, consumer appliance subsystems, and automotive body electronics where the -40C to +125C rating is required. The 8-pin DFN package suits miniature PCBs in wearables, IoT edge nodes, and remote control units. When designing with the PIC12F510-E/MC, ensure that the 8-pin DFN (2x3 mm) land pattern is properly designed with adequate thermal pad soldering to meet IPC-7351 standards, and verify that the 6 I/O pins are sufficient for your application. Use MPLAB X IDE with XC8 compiler for development. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

RFQ যোগাযোগ
PIC12F510-E/MS - 8-Bit 8MHz Flash MCU | Microchip Technology
PIC12F510-E/MS

PIC12F510-E/MS - 8-Bit 8MHz Flash MCU | Microchip Technology

The Microchip Technology PIC12F510-E/MS is an 8-bit flash-programmable PIC microcontroller with an 8 MHz maximum clock, 1.5 KB of program memory organized as 1K × 12 words, 38 bytes of RAM, and six I/O ports in an 8-pin MSOP package. The PIC12F510-E/MS is specified for extended-temperature operation from -40°C to +125°C. A small 8-bit microcontroller is a compact embedded-control device used to read sensors, operate user controls, monitor digital signals, and control simple actuators. Within the broader semiconductor hierarchy, the PIC12F510 is a flash-programmable microcontroller, part of Microchip's PIC 12F family and the broader category of embedded processing devices. Its small memory footprint makes it most appropriate for compact control tasks that do not require a high-performance processor or a large application firmware image. The device provides six I/O ports, allowing external buttons, indicators, logic signals, and simple peripherals to be connected while conserving board area. Its 1.5 KB program memory offers 1K × 12 words of programmable code storage, while 38 bytes of RAM support variables, working state, and short instruction sequences. Serial in-system programming supports flexible programming workflows, including programming a device while it is installed in the target circuit. Power-conscious embedded designs can use the PIC12F510's power-saving Sleep mode to reduce activity between external events. A watchdog timer supports system recovery after unexpected hangs, while code-protection features help guard programmed application firmware against unauthorized access. These capabilities make the device appropriate for compact control, monitoring, and low-cost automation products where reliability and a small PCB footprint matter. Typical uses include building controls, appliance interfaces, small motor-control helpers, sensor nodes, LED status controllers, and simple industrial monitoring modules. The six available I/O ports should be allocated around the actual interface requirement rather than treated as a replacement for a larger bus controller. Firmware complexity must remain within the 1.5 KB program-memory limit, and any interrupt-driven design should account for the limited RAM available. When laying out the PCB, reserve the MSOP-8 land pattern and route programming access to the device's serial programming interface. Confirm the operating voltage and decoupling requirements against the manufacturer datasheet for the exact supply condition. Keep the implementation compatible with the -40°C to +125°C temperature range when the product must operate in industrial, automotive-adjacent, or extended industrial environments. This product page combines the manufacturer datasheet, official product information, programming guidance, and component-level cross-reference information. It also provides application guidance, a pin-oriented package view, and engineering comparisons that help evaluate the PIC12F510-E/MS as a compact embedded-control solution.

RFQ যোগাযোগ
PIC12F510-E/P - 8-bit Flash MCU, 1.5KB Flash, 6 I/O | Microchip
PIC12F510-E/P

PIC12F510-E/P - 8-bit Flash MCU, 1.5KB Flash, 6 I/O | Microchip

The Microchip Technology PIC12F510-E/P is an 8-bit flash-based CMOS microcontroller in the PIC12F family, featuring 1.5KB of flash program memory (1K x 12), 38 bytes of RAM, and 6 I/O pins, packaged in an 8-pin PDIP through-hole format. It operates at up to 4 MHz internal clock speed from a 2V to 3V supply range, providing a compact solution for cost-sensitive and space-constrained embedded designs. The 'E' suffix denotes the Extended operating temperature grade of -40C to +125C, making the part suitable for industrial and harsh-environment deployments. What is an 8-bit flash microcontroller? An 8-bit flash microcontroller is a small, self-contained computer on a chip that uses an 8-bit data path and on-chip flash memory for program storage. The PIC12F510 belongs to the broader category hierarchy: microcontroller -> MCU -> embedded controller -> semiconductor IC. It uses Microchip's enhanced PIC mid-range core with a 12-bit instruction word, giving it higher code density than typical 8-bit CISC competitors. The 1.5KB flash and 38-byte RAM place it at the low end of the PIC12F lineup, optimized for simple control loops, glue logic replacement, and standby/always-on applications. Key features include nanoWatt power management for low standby current (typical applications cite <1 uA sleep), an internal 4 MHz oscillator that eliminates the need for an external crystal in most designs, and a wide operating voltage range from 2V to 5.5V depending on configuration. The 6 I/O pins can be multiplexed for digital I/O, analog comparator inputs, or timer/counter functions. The 8-pin PDIP package provides a robust through-hole footprint for prototyping and industrial hardware where mechanical stress or hand-solder rework is required. The architecture uses a RISC-style instruction set with only 33 single-word instructions, simplifying firmware development and reducing code size. Each instruction executes in a single instruction cycle (200 ns at 8 MHz, 1 us at 4 MHz), giving deterministic interrupt response for real-time control. The 12-bit-wide instructions provide 2:1 code compression over typical 8-bit CISC MCUs in the same price range, allowing more functionality to fit in the 1.5KB flash. Typical applications include battery-powered sensor nodes, LED lighting controllers, simple motor drivers, household appliance sub-controls, and standby power management in larger systems. The nanoWatt technology and 2V minimum supply make it particularly well-suited for 2xAA battery or single-cell lithium applications. When designing with the PIC12F510-E/P, choose the 'E' (extended) temperature grade for industrial environments and the 'I' grade for commercial use. Verify the supply voltage matches your battery or rail configuration - 2V to 5.5V operation spans most portable and 3.3V/5V systems. For designs that may need more flash or peripherals, consider PIC12F615 or PIC12F1840 as upward-compatible migrations on the same 8-pin footprint. This page synthesizes distributor pricing, drop-in cross-brand alternatives, and practical design notes that extend beyond the manufacturer datasheet, including parametric comparison, selection guidance for industrial vs commercial grades, and explicit pinout validation rules.

RFQ যোগাযোগ
PIC12F510-E/SN - 8-Bit 8MHz Flash MCU, 1.5KB | Microchip
PIC12F510-E/SN

PIC12F510-E/SN - 8-Bit 8MHz Flash MCU, 1.5KB | Microchip

The Microchip Technology PIC12F510-E/SN is an 8-bit Flash-programmable RISC microcontroller in an 8-pin SOIC package, running at up to 8 MHz internal oscillator and featuring 1.5 KB (1K x 12) of Flash program memory. It is part of Microchip's PIC12 mid-range core family, designed for cost-sensitive embedded control with 6 general-purpose I/O pins, 38 bytes of RAM, and a 64-byte EEPROM. The -E suffix designates the extended industrial temperature range of -40C to +125C. What is an 8-bit PIC microcontroller? A PIC (Peripheral Interface Controller) is a RISC microcontroller family originally developed by General Instrument and now maintained by Microchip Technology. The PIC architecture uses a Harvard bus with separate program and data memory spaces and a small, fixed instruction set optimized for deterministic single-cycle execution. The PIC12F sub-family sits at the entry level of the PIC10/12/16 hierarchy, targeting the smallest 6- and 8-pin packages for compact, low-cost designs. Key features include 1.5 KB Flash program memory (rated for 100K erase/write cycles), an internal 8 MHz precision oscillator, a wide operating voltage range of 2.0 V to 5.5 V, an analog comparator, an 8-bit ADC with up to 4 input channels, and ultra-low-power sleep modes drawing less than 1 uA. The on-chip debug (ICD) support enables in-circuit programming and debugging, eliminating the need for an external programmer in development workflows. A hardware Watchdog Timer with its own on-chip RC oscillator provides reliable system recovery. The PIC12F510 uses a 14-bit instruction word within the PIC12/16 mid-range core, providing 33 single-word instructions and a hardware multiplier-free design that simplifies compiler targeting. With only 8 pins, the device multiplexes digital I/O, ADC inputs, comparator inputs, and ICSP programming onto the same pads, requiring careful pin assignment during firmware development. The device supports both internal and external oscillator modes, plus a power-on timer and brown-out reset for robust cold-start behavior. Typical applications include battery-powered sensor nodes, consumer appliance controllers, LED lighting drivers, simple motor control (small DC fans), automotive accessory modules, and hobbyist/maker projects. The combination of tiny footprint, low power, and proven PIC toolchain (MPLAB X + XC8 compiler) makes it a frequent choice for retrofit designs replacing older PIC12C508/PIC12C509 OTP parts. When designing with this part, note that the 6 I/O pins are heavily multiplexed - the same pin that drives an LED may also serve as an ADC input or comparator reference. Plan pin allocation early and reserve GP3 for ICSP programming if in-circuit updates are required. The internal 8 MHz oscillator provides sufficient timing accuracy for UART bit-banging but is not suitable for protocols demanding tight clock tolerance such as CAN or USB. This page synthesizes distributor pricing, drop-in PIC alternatives, and practical design notes not found in the manufacturer datasheet, helping engineers select the right 8-pin Flash MCU for cost-driven embedded designs.

RFQ যোগাযোগ
PIC12F510-I/MC - 8-bit MCU, 1.5KB Flash, 8MHz, DFN-8 | Microchip
PIC12F510-I/MC

PIC12F510-I/MC - 8-bit MCU, 1.5KB Flash, 8MHz, DFN-8 | Microchip

The Microchip Technology PIC12F510-I/MC is an 8-bit PIC RISC flash microcontroller with 1.5 KB of program memory, 38 bytes of RAM, and 64 bytes of EEPROM, packaged in a compact 8-pin DFN (3 mm x 2 mm) plastic lead-free housing. It operates from 2.0 V to 5.5 V and runs instructions at up to 8 MHz (4 MHz internal oscillator), delivering 1 MIPS of throughput while consuming only a few hundred microamperes active. According to the Microchip datasheet, the device integrates a 4-channel 8-bit ADC, two analog comparators, one 8-bit timer and one 16-bit timer, plus a watchdog timer for safe field deployment. An 8-bit microcontroller (MCU) is a single-chip computer built around an 8-bit data path that fetches, decodes, and executes instructions from on-chip program memory. PIC microcontrollers from Microchip use a Harvard RISC architecture with separate program and data buses, and the PIC12F510 belongs to the baseline-friendly PIC12F family positioned between the PIC10F and PIC16F tiers. Within the broader taxonomy: microcontroller -> embedded controller -> semiconductor IC -> integrated circuit. PIC12F MCUs are typically deployed as glue logic, sensor front-ends, and low-power controllers in cost-sensitive applications. Key differentiating features include 1.5 KB self-programmable Flash, 38 bytes of SRAM, integrated 8-bit ADC with up to 4 input channels, dual on-chip comparators that can wake the core, internal 4 MHz oscillator that eliminates external crystals, and an automotive-grade AEC-Q100 qualification in this part variant. The DFN-8 (also called MC) package measures just 3 mm x 2 mm with an exposed thermal pad, making it one of the smallest Microchip PIC offerings and ideal for footprint-constrained PCB designs. Technically, the PIC12F510 uses a 12-bit instruction word with single-cycle execution on most instructions except branches, yielding an effective 2:1 code compression advantage over typical 8-bit CISC MCUs. The 4 MHz internal oscillator can be used directly or post-scaled to provide a system clock, and the watchdog timer uses its own dedicated internal RC for maximum reliability. Six general-purpose I/O pins (GP0-GP5) are multiplexed with ADC inputs and comparator I/O, and four of them support interrupt-on-change. Typical applications include AEC-Q100 automotive body controllers (window lifters, mirror controllers, RKE receivers), battery-powered sensor nodes, LED driver controllers, low-cost fan controllers, smoke detector front-ends, and simple appliance user-interface replacements for mechanical timers. The wide 2.0 V to 5.5 V operating range also supports single-cell Li-ion or two-AA-cell battery stacks without additional regulation. When designing with the PIC12F510, place a 100 nF decoupling capacitor within 2 mm of the VDD pin and connect the exposed pad (EP) directly to the ground plane for thermal relief and short-loop return paths. Because the device is in-circuit serial programmable (ICSP), reserve the ICSPCLK/ICSPDAT pins and add a programming header for production firmware loading. This page synthesizes distributor pricing, drop-in same-brand alternatives, and practical design notes not found in the manufacturer datasheet. Engineers get a parameter-by-parameter comparison and explicit cross-brand candidates where pin-compatible.

RFQ যোগাযোগ
PIC12F510-I/MS - 8-bit MCU, 1.5KB Flash, 8MHz, MSOP-8 | Microchip
PIC12F510-I/MS

PIC12F510-I/MS - 8-bit MCU, 1.5KB Flash, 8MHz, MSOP-8 | Microchip

The Microchip Technology PIC12F510-I/MS is a low-power, 8-bit CMOS Flash-based microcontroller in the PIC12 8-pin family, offering 1.5 KB (1K x 12 words) of Flash program memory, 41 bytes of RAM, and 63 bytes of data EEPROM in an 8-lead MSOP package. It executes instructions at up to 8 MHz (4 MHz internal RC), integrates a 4-channel 8-bit ADC and a comparator on-chip, and provides 6 general-purpose digital I/O pins for compact embedded designs. An 8-bit PIC microcontroller (MCU) is a single-chip computer built around an 8-bit data path that integrates a CPU core, non-volatile program memory (Flash/ROM), volatile working memory (RAM), non-volatile data storage (EEPROM), and configurable peripheral blocks (timers, ADC, comparators, communication peripherals). PIC12F-series MCUs sit at the ultra-small-pincount end of the PIC family (8 pins), targeting cost- and space-constrained applications such as LED drivers, sensor signal conditioning, battery chargers, and remote-control front ends where the 12-bit-wide instruction set delivers ~2:1 code density versus competing 8-bit cores. Key specifications include 1.5 KB Flash program memory, 41 bytes SRAM, 63 bytes EEPROM, an operating voltage range of 2.0 V to 5.5 V, and an industrial temperature range of -40 °C to +85 °C. The device integrates a high-performance RISC CPU with only 33 single-word/single-cycle instructions, an 8-bit timer/counter (TMR0), a watchdog timer, an 8-bit ADC with 4 input channels and 4 multiplexed channels, and one analog comparator. The MSOP-8 package provides a compact 3 x 3 mm footprint ideal for space-limited designs. Architecturally, the PIC12F510 is built on Microchip's baseline 8-bit core with a 12-bit instruction word, supporting direct, indirect, and relative addressing modes. The Flash memory supports in-circuit serial programming (ICSP) via two pins, enabling firmware updates after PCB assembly. The ADC uses successive-approximation register (SAR) conversion with software-selectable acquisition time, and the comparator offers programmable reference and output polarity. Power-saving features include a Sleep mode with wake-up on pin change and a clock-monitoring circuit. Typical applications include battery-powered sensor nodes, LED lighting controllers, small appliance controls, automotive interior lighting, fan/thermostat controllers, and consumer remote controls. The combination of integrated ADC, comparator, and EEPROM makes it well-suited for standalone analog signal conditioning without external components. When designing with this MCU, ensure decoupling caps of 0.1 µF are placed close to VDD, and reserve the ICSPDAT/ICSPCLK pins (typically GP0/GP1) for in-circuit programming unless they are also used in the final application. The internal 4 MHz oscillator provides ±1% accuracy after calibration and avoids the need for external crystals in most applications. This page synthesizes distributor pricing, drop-in PIC12 family alternatives, and practical design notes not found in the manufacturer datasheet alone.

RFQ যোগাযোগ
PIC12F510-I/P - 8-bit Flash MCU, 1.5KB, 8MHz, 6 I/O | PDIP-8
PIC12F510-I/P

PIC12F510-I/P - 8-bit Flash MCU, 1.5KB, 8MHz, 6 I/O | PDIP-8

The Microchip Technology PIC12F510-I/P is an 8-bit Flash-based CMOS microcontroller in an 8-pin PDIP package, offering 1.5KB (1K x 12) of Flash program memory, 38 bytes of RAM, and 6 I/O pins. Operating at up to 8MHz internal oscillator across a 2.0V to 5.5V supply range, it targets cost-sensitive embedded applications requiring minimal board area and low power consumption via Microchip's nanoWatt technology. A microcontroller (MCU) is a single-chip computer containing a CPU core, non-volatile program memory (Flash/ROM), volatile data memory (RAM), and programmable I/O peripherals. Within the embedded hierarchy, the PIC12F510 sits in the low-pin-count 8-bit segment of Microchip's PIC® family, which is broadly classified as: microcontroller -> embedded controller -> semiconductor IC. The 8-bit PIC architecture uses a RISC-like Harvard structure with separate program and data buses, prioritizing deterministic instruction timing and code density for simple control tasks rather than raw throughput. Key features include a 33-instruction set, eight-bit timer with 8-bit prescaler, four-channel 8-bit A/D converter, watchdog timer with on-chip oscillator, in-circuit serial programming (ICSP), and an internal 4/8MHz oscillator that eliminates the need for an external crystal. Power management features include nanoWatt sleep modes drawing typical standby currents below 100 nA, making the device attractive for battery-powered sensor and consumer appliances. The PIC12F510 shares its silicon core and instruction set with the 14-pin PIC16F506, providing a migration path to additional I/O when board space allows. Code is generated using MPLAB X IDE with the free XC8 compiler, and debug is supported via optional header connections. Compared to discrete logic implementations, the device integrates timing, sensing, and glue logic on a single die, reducing PCB area, BOM count, and assembly cost. Typical applications include battery chargers, LED lighting controllers, small fan/thermostat controls, appliance user-interface replacement, and remote sensor transmitter nodes. The internal oscillator and integrated ADC allow complete system designs without external clock or signal-conditioning components. When designing with the PIC12F510, use the ICSP interface (VPP, ICSPCLK, ICSPDAT) on dedicated pins and reserve one I/O for the MCLR reset if hardware reset is required. Industrial-grade temperature rating (-40C to +85C) suits most indoor and protected-environment deployments; for harsher environments choose the -E or -T industrial/automotive variants. This page synthesizes distributor pricing, drop-in package alternatives, and practical design notes not consolidated on the manufacturer datasheet, enabling faster part selection and BOM risk analysis.

RFQ যোগাযোগ
PIC12F510-I/SN - 8-Bit Flash MCU, 1.5KB, 8MHz, 8-SOIC | Microchip
PIC12F510-I/SN

PIC12F510-I/SN - 8-Bit Flash MCU, 1.5KB, 8MHz, 8-SOIC | Microchip

The Microchip Technology PIC12F510-I/SN is an 8-bit PIC® mid-range Flash microcontroller in a 8-pin SOIC (SN) package, featuring 1.5KB (1K x 12) of Flash program memory, 41 bytes of RAM, and an 8MHz internal oscillator. It is rated for an industrial temperature range of -40C to +85C and operates from 2.0V to 5.5V across the PIC12F510 family. An 8-bit PIC microcontroller (PIC = Peripheral Interface Controller) is a Harvard-architecture RISC device that executes one instruction per clock cycle (except branches). The PIC10/12 family occupies the smallest-footprint tier of Microchip's 8-bit portfolio - it sits below PIC16 and PIC18 in memory/peripheral capability but offers the lowest unit cost and smallest PCB area, sucing applications where cost, simplicity and pin count dominate over raw performance. The PIC12F510 specifically belongs to the mid-range 14-bit instruction-word core family and integrates analog peripherals on-chip. Key features of the PIC12F510 include 6 general-purpose I/O pins, one 8-bit ADC with up to 4 input channels, an analog comparator, a 4-MHz internal RC oscillator (4 MHz CPU clock via 2:1 divider from 8 MHz oscillator), and an 8-bit timer/counter (TMR0). According to the manufacturer datasheet, the part supports in-circuit serial programming (ICSP) and code protection, and it draws a few hundred microamps active / sub-microamp sleep. Architecturally, the PIC12F510 uses a 14-bit instruction word, separate program and data buses (Harvard), and a 2-stage pipeline. The internal 8 MHz oscillator can be software-calibrated via the OSCCAL register to recover accuracy after calibration-register erasures. The device supports two oscillator modes (internal RC and external clock) and offers power-managed sleep with wake-on-change I/O. Typical applications include low-cost consumer appliances, LED lighting controllers, battery chargers, remote-control transmitters, and simple sensor interface boards. The combination of an on-chip ADC, comparator and 6 I/O in an 8-pin package makes the PIC12F510 well suited for replacing discrete logic in space-constrained designs. When designing with the PIC12F510, ensure the ICSP clock (PGC) and data (PGD) pins are accessible on the PCB for in-system programming. For battery-powered designs, leverage the device's sleep modes (sub-1 uA typical) and use the internal weak pull-ups to reduce external component count. This page synthesizes distributor pricing, drop-in same-package alternatives, and engineering design notes not aggregated on any single distributor page, helping procurement and design engineers evaluate the PIC12F510-I/SN for cost-sensitive 8-bit embedded designs.

RFQ যোগাযোগ
PIC12F510T-I/MC - 8-Bit MCU, 1.5KB Flash, 8MHz, 8-DFN | Microchip
PIC12F510T-I/MC

PIC12F510T-I/MC - 8-Bit MCU, 1.5KB Flash, 8MHz, 8-DFN | Microchip

The Microchip Technology PIC12F510T-I/MC is an 8-bit RISC Flash microcontroller in the PIC12 family, featuring 1.5KB (1K x 12) of Flash program memory, 38 bytes of SRAM, and 64 bytes of EEPROM data memory, all integrated into a compact 8-pin DFN (2x3 mm) package. It operates at up to 8 MHz from a 2.0V to 5.5V supply and integrates a 4-channel 8-bit ADC, one analog comparator, and a hardware timer with capture/compare/PWM capability. An 8-bit PIC microcontroller is a compact, deterministic Harvard-architecture MCU built around a reduced instruction set (RISC) core. The PIC12 family sits at the low-end of Microchip's PIC line: microcontrollers -> 8-bit microcontrollers -> PIC microcontroller -> PIC12 family -> PIC12F subfamily (Flash-based, small-pin-count). The PIC12F510T-I/MC belongs to this Flash-programmable 8/14-pin subfamily targeting cost-sensitive, space-constrained designs. Key features include 33 single-word instructions, 8-level hardware stack, four ADC channels with 8-bit resolution, one on-chip comparator with programmable reference, an 8-bit timer with 8-bit prescaler, and ultra-low-power sleep mode drawing microamp-level current. The internal 4 MHz RC oscillator and optional 8 MHz internal clock eliminate the need for external crystals in many applications, reducing BOM cost and PCB footprint. Typical applications include battery-powered sensor nodes, LED drivers, simple motor control, battery chargers, and consumer appliance interfaces. The compact 8-DFN package and wide operating voltage range make the PIC12F510T-I/MC well-suited for handheld and portable products where PCB area is at a premium. When designing with this device, allocate sufficient bypass capacitance (0.1 uF ceramic) close to VDD, and note that the I/MC package uses 8-DFN with an exposed pad (EP) that should be soldered to the ground plane for thermal dissipation. Programming is performed via ICSP (In-Circuit Serial Programming) on the GP0/GP1 pins. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

RFQ যোগাযোগ
PIC12F510T-I/MS - 8-Bit 8MHz PIC12 MCU, 1.5KB FLASH | Microchip
PIC12F510T-I/MS

PIC12F510T-I/MS - 8-Bit 8MHz PIC12 MCU, 1.5KB FLASH | Microchip

The Microchip Technology PIC12F510T-I/MS is an 8-bit PIC12-family RISC microcontroller IC offering 8MHz maximum clock speed, 1.5KB (1K x 12) of Flash program memory, and 38 bytes of data RAM, supplied in an 8-pin MSOP package with tape-and-reel packaging. The suffix T indicates tape-and-reel delivery, I indicates the industrial -40C to +85C operating temperature range, and MS denotes the 8-MSOP plastic surface-mount package. Six general-purpose I/O pins are available for application use, along with an integrated 8MHz internal oscillator that reduces bill-of-material cost by eliminating external clock hardware. A microcontroller (MCU) is a single-chip computer containing a CPU core, program memory, data RAM, and programmable I/O peripherals. The PIC12F510 belongs to the baseline 12-bit instruction-word PIC10/12 family, sitting in the broader 8-bit MCU category which also includes 8051 and AVR architectures. Within Microchip's portfolio, the PIC12 sub-family targets small-form-factor, low-pin-count, cost-sensitive embedded applications where 6-8 I/O pins and 1-3KB of code space are sufficient. The PIC12F510 specifically occupies the entry-level position designed for ultra-low-cost analog and digital control replacing discrete logic or electromechanical timers. Key features include 1.5KB self-programmable Flash (in-circuit serial programming via ICS), 38 bytes SRAM, a 4-channel 8-bit ADC with internal voltage reference, one 8-bit timer (TMR0), one watchdog timer with separate oscillator, and an internal 4MHz/8MHz precision oscillator. Power consumption is optimized for battery operation, with operating voltage from 2.0V to 5.5V (typical 2.5V/3.3V/5V rails supported), brown-out reset protection, and an extended instruction set capable of executing most instructions in a single 200ns cycle at 20MHz external. The PIC12F510 uses a Harvard RISC architecture with separate program and data buses. Its 12-bit instruction word (33 single-word instructions, mostly single-cycle) and 2-stage pipeline deliver deterministic interrupt latency - typically 200ns at 8MHz. The integrated 4MHz/8MHz RC oscillator is factory calibrated to +/-1% accuracy across temperature and voltage, removing the need for external crystals in cost-sensitive applications and shrinking PCB footprint. An on-chip debug module is not present; developers use ICSP for programming and a debug header is optional. Typical applications include ultra-low-cost consumer appliances, LED lighting controllers, simple sensor interfaces, battery chargers, IR remote control transmitters, smart toys, and replacement of discrete logic/timer circuits. The wide 2.0V to 5.5V supply range supports single-cell Li-ion (3.7V nominal), two-cell AA, and 5V regulated rails. Industrial temperature rating and small MSOP-8 footprint also suit automotive interior and harsh-environment sensor nodes. When designing with the PIC12F510, ensure your code fits within the 1K-instruction Flash and 38-byte RAM budget - compile-time checks for stack depth and RAM bank usage are critical because the device lacks a hardware stack overflow indicator. Decouple VDD with a 100nF ceramic capacitor close to the pin, and route GP3/MCLR through a 10k pull-up unless using the internal MCLR disable fuse. Unlike newer PIC16F1xxx parts, the PIC12F510 has no CWG/NCO/CLC peripherals, so waveform generation and arithmetic-heavy tasks may require the newer PIC12F1501 or PIC16F15313 (the suggested migration per Microchip). This page synthesizes distributor pricing, drop-in Microchip alternatives, and practical design notes not found in the manufacturer datasheet alone.

RFQ যোগাযোগ
PIC12F519-E/MC - 8-Bit Flash MCU, 1.5KB, 4MHz, DFN-8 | Microchip
PIC12F519-E/MC

PIC12F519-E/MC - 8-Bit Flash MCU, 1.5KB, 4MHz, DFN-8 | Microchip

The Microchip PIC12F519-E/MC is a low-cost, high-performance 8-bit Flash-based CMOS microcontroller in an 8-pin DFN (3x2 mm) package, featuring a RISC core with 33 single-word/single-cycle instructions running at up to 8 MHz (4 MHz factory default) with a 500 ns instruction cycle. It integrates 1.5 KB of Flash program memory, 64 bytes of Flash data EEPROM, and 41 bytes of SRAM, supported by 6 I/O pins. The device operates from 2.0V to 5.5V across the extended -40C to +125C industrial temperature range. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, program memory (Flash/ROM), data memory (RAM), and peripherals onto one die, typically targeted at cost-sensitive embedded control tasks. Within the product hierarchy, the PIC12F519 belongs to the PIC10/12 family of baseline and mid-range 8-bit microcontrollers -> microcontrollers -> embedded processors -> integrated circuits -> semiconductors. The '12-bit wide instruction set' is a Microchip hallmark offering 2:1 code density over 8-bit instruction MCUs from competitors, and the device also carries the legacy PIC12C5xx core, making it familiar to long-time PIC users. Key features include an internal 4 MHz factory-calibrated oscillator with software-selectable LF (31 kHz) and HF (8 MHz) modes, an 8-bit real-time clock/counter (TMR0) with 8-bit prescaler, a Watchdog Timer (WDT) with its own on-chip RC oscillator for reliable operation, and ultra-low-power nanoWatt technology with power-managed sleep and wake-up modes. Code protection, Power-on Reset (POR), and Brown-out Reset (BOR) are built in, and in-circuit serial programming (ICSP) is supported via two pins. The PIC12F519 uses a Harvard RISC architecture with separate program and data buses, providing deterministic single-cycle instruction execution. Its peripheral set is intentionally minimal—PORTA with six GPIO pins, an 8-bit timer, and an analogue comparator selectable on GP0/GP1/GP2—optimised for compact glue-logic replacement and battery-powered applications rather than high-throughput DSP tasks. Typical applications include battery chargers, smart sensors, appliance controls, LED drivers, low-end remote controls, and small motor controllers. The extended temperature range also supports industrial monitoring nodes and automotive body electronics (non-safety). It fits particularly well where PIC12C508/PIC12C509 firmware is already deployed and a Flash-based migration is desired. When designing with this device, allocate I/O pins carefully because only 6 of the 8 package pins are usable as GPIO; the remaining 2 are VDD/VSS. Place a 0.1 uF decoupling capacitor as close to the VDD pin as the DFN-8 land pattern allows, and follow Microchip's recommended ICSP layout for in-circuit programming access. This page consolidates manufacturer specification data, distributor pricing as of 2026-09-15, a side-by-side drop-in compatibility table against PIC12F510/PIC12F509/PIC12F1822 family parts, and practical design guidance not found in the standalone datasheet.

RFQ যোগাযোগ
PIC12F519-E/MS - 8-bit 8MHz 1.5KB Flash MCU 8-MSOP | Microchip
PIC12F519-E/MS

PIC12F519-E/MS - 8-bit 8MHz 1.5KB Flash MCU 8-MSOP | Microchip

The Microchip Technology PIC12F519-E/MS is an 8-bit, fully-static, Flash-based CMOS RISC microcontroller in an 8-pin MSOP package. It runs at up to 8 MHz instruction rate and integrates 1.5 KB (1K x 12) of Flash program memory plus 64 bytes of RAM, making it a compact, low-cost solution for pin-constrained embedded applications. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory, working RAM, and configurable peripherals around a shared bus. The PIC12F519 belongs to the PIC12F family of baseline and mid-range 8-bit PIC microcontrollers, which sit under the broader PIC microcontroller umbrella and ultimately the Microcontroller (MCU) -> Microcomputer -> Embedded Computing product hierarchy. nanoWatt power-management technology gives the PIC12F519 deep sleep and active-clock modes, allowing the device to draw microamps in standby, which is critical for battery-powered IoT sensors and remote controls. Key differentiating features include 33 single-word/single-cycle RISC instructions, 8 MHz internal oscillator, 6 general-purpose I/O pins shared with peripheral functions, 8-bit timer with watchdog, and an enhanced Flash program memory that supports in-circuit serial programming (ICSP). The PIC12F519 is specified for 2.0V to 5.5V operation across -40C to +125C (E temperature grade), enabling use in both consumer and industrial environments. The PIC12F519 is built on a baseline RISC core with single-cycle instruction execution and hardware multiply support, achieving deterministic interrupt latency. The integrated 8 MHz internal oscillator eliminates the need for external resonators on low-cost boards, while the ICSP interface enables field updates without removing the device. Typical applications include consumer remote controls, LED lighting controllers, low-end sensor nodes, appliance user interfaces, security PIR subsystems, and general-purpose logic-replacement boards where a few smart pins replace discrete logic. When designing with the PIC12F519-E/MS, leave one pin dedicated to ICSP programming (typically GP1/GP0) and pay attention to the absolute maximum VDD of 5.5V. Use the WDT and Brown-out Reset features to harden firmware in electrically noisy environments, and consult Microchip's nanoWatt design notes to minimize average current for battery applications. This page synthesizes Microchip datasheet parameters, current distributor pricing (as of 2026-09-15), drop-in MSOP-8 alternatives, and practical design notes not consolidated in the manufacturer datasheet.

RFQ যোগাযোগ