মাইক্রোকন্ট্রোলার

পণ্য (20,000+)

PIC12LF1822T-I/RF - 8-bit 32MHz MCU 3.5KB Flash | Microchip
PIC12LF1822T-I/RF

PIC12LF1822T-I/RF - 8-bit 32MHz MCU 3.5KB Flash | Microchip

The Microchip Technology PIC12LF1822T-I/RF is an 8-bit PIC microcontroller from the PIC12 family delivering 32MHz CPU performance, 3.5KB (2K x 14 words) of Flash program memory, 128 bytes of SRAM, and 256 bytes of EEPROM in an 8-pin UDFN (3x3 mm) package. It belongs to the PIC12F/LF1822 sub-family, an enhanced mid-range core with nanoWatt XLP technology for ultra-low-power operation. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), data memory (SRAM, EEPROM), and peripheral subsystems (ADC, timers, communication interfaces) into one package. The PIC12F/LF1822 occupies the hypernym hierarchy: 8-bit MCU -> microcontroller -> embedded processor -> semiconductor IC. The 'LF' suffix denotes the wide-voltage 1.8V-3.6V variant optimized for battery-powered applications, while the non-LF 'F' variant targets 2.3V-5.5V rails. Key features include a 10-bit ADC with up to 12 channels, two 8-bit timers plus one 16-bit timer, enhanced PWM, an MSSP module supporting SPI and I2C, an EUSART for UART, an on-board configurable reference, and an internal 32MHz oscillator. The nanoWatt XLP technology achieves sub-microamp sleep currents, making the part suitable for energy-harvesting and coin-cell designs. Five selectable oscillator modes cover crystals, resonators, and external clocks up to 32MHz. The PIC12LF1822 uses an enhanced mid-range 8-bit RISC core with a 14-bit instruction word and a single-cycle hardware multiplier. Harvard architecture separates program and data buses for deterministic 8MIPS throughput at 32MHz. On-chip in-circuit debug support allows MPLAB X IDE debugging without an external debug header, though AC244044 is available as an LF-version external header. Typical applications include IoT sensor nodes, wearable health patches, wireless remote controls, LED driver controllers, battery-powered instrumentation, and small-form-factor consumer devices. The wide 1.8V-3.6V range enables direct connection to single Li-ion, two-coin-cell, or alkaline battery stacks without additional regulation. Designers should reserve pin 1 (VDD) and pin 8 (VSS) for the lowest-impedance supply decoupling - typically 100nF ceramic placed within 2mm of the pads. The ICSP/ICD pins (RA5/RA0) require isolation resistors in production designs to avoid contention with application circuitry. This page synthesizes distributor pricing, parametric drop-in alternatives, and practical design notes not consolidated in the manufacturer datasheet.

RFQ যোগাযোগ
PIC12LF1822T-I/SN - 8-bit XLP MCU 3.5KB FLASH 8-SOIC | Microchip
PIC12LF1822T-I/SN

PIC12LF1822T-I/SN - 8-bit XLP MCU 3.5KB FLASH 8-SOIC | Microchip

The Microchip Technology PIC12LF1822T-I/SN is an 8-bit PIC12 XLP (eXtreme Low Power) microcontroller IC running up to 32MHz internal oscillator, integrating 3.5KB (2K x 14) of Flash program memory and 128 bytes of RAM in an 8-pin SOIC (SN) package supplied on Tape & Reel. According to the verified web data, the device operates over a 2.3V to 3.6V supply range (with operation down to 1.8V supported at 16MHz per the manufacturer datasheet family specification) and exposes 6 general-purpose I/O pins with rich on-chip peripherals. An 8-bit microcontroller (MCU) is a small, self-contained computing element that combines a CPU, non-volatile program memory, working RAM, and configurable peripherals on a single CMOS die. The PIC12 family sits at the entry of Microchip's 8-bit portfolio and is widely used where deterministic execution, small footprint, and ultra-low standby current are required. Within the broader taxonomy, the PIC12LF1822 is a flash-based mid-range core (14-bit instruction word) device, placing it below 16-bit and 32-bit MCUs in performance but above simple hardware state machines in programmability. Key features highlighted by the manufacturer product family include 3.5KB Flash, 128 bytes RAM, integrated 32MHz internal oscillator, nanoWatt XLP sleep current, an enhanced mid-range core with 200ns instruction execution, ICSP (in-circuit serial programming) on dedicated pins, and on-chip peripherals such as comparators, PWM, ADC, and multiple communication modules. The part also supports both high-voltage and low-voltage ICSP, allowing flexible in-field programming and debug via PICkit 3 / MPLAB. Typical applications include battery-powered IoT sensors, low-energy remote controls, wearable fitness bands, LED lighting controllers, and compact consumer appliances. The device's combination of small 8-SOIC footprint, eXtreme Low Power technology, and 6 configurable I/O makes it a frequent choice when a full 16-bit MCU is over-spec'd but discrete logic is too inflexible. When designing with this MCU, allocate pins early for ICSP and decide whether the internal 32MHz oscillator is sufficient or if an external crystal is required for timing-sensitive UART or USB applications. Ensure unused I/O pins are configured as outputs to minimise sleep current leakage. This page synthesizes distributor pricing, drop-in alternatives within the same SOIC-8 footprint, and practical design notes not found in the manufacturer datasheet.

RFQ যোগাযোগ
PIC12LF1840-E/MF - 8-Bit XLP MCU 7KB 8-DFN | Microchip
PIC12LF1840-E/MF

PIC12LF1840-E/MF - 8-Bit XLP MCU 7KB 8-DFN | Microchip

The Microchip Technology PIC12LF1840-E/MF is an 8-bit PIC microcontroller in the nanoWatt XLP family, featuring 7KB (4K x 14) of Flash program memory and running at up to 32MHz internal oscillator. It is housed in an 8-pin DFN (3x3 mm) package with exposed pad, operates from 1.8V to 3.6V (LF variant), and integrates peripheral interfaces including ADC, PWM, comparators, and configurable logic cells in a footprint smaller than a SOIC-8. A microcontroller (MCU) is a single-chip computer containing a CPU core, program memory (Flash), data memory (RAM), EEPROM, and on-chip peripherals. Within the hierarchy, PIC12LF1840 belongs to the 8-bit PIC10/12/16 family of microcontrollers -> mid-range enhanced core architecture -> RISC microcontrollers -> embedded computing ICs -> semiconductors. The PIC12LF1840 is the low-voltage 'LF' member of the PIC12F1840 family, optimized for battery-friendly operation with nanoWatt XLP technology achieving sub-uA sleep currents. Key features include 32MHz max CPU speed via internal oscillator (8MHz factory calibrated), 256 bytes of EEPROM data memory, 256 bytes of RAM, six I/O pins multiplexed with peripherals, 10-bit ADC with up to 4 channels, enhanced PWM, comparators, EUSART, MSSP (SPI/I2C), and configurable logic cells. The 8-DFN package at 3x3mm makes it one of the smallest PIC microcontrollers available while retaining an exposed pad for thermal dissipation and ground integrity. The PIC12LF1840 uses Microchip's enhanced mid-range core with 49 instructions, 16-level hardware stack, and self-read/write Flash capability. Internal oscillator accuracy reaches ±1% after calibration, supporting UART communication without an external crystal in most designs. The nanoWatt XLP technology delivers typical sleep currents below 100 nA, enabling multi-year battery life on coin cells. Typical applications include battery-powered IoT sensor nodes, wearable electronics, remote controls, low-power wireless sensor transmitters, LED lighting controllers, and consumer accessories. The combination of small footprint, wide peripheral integration, and ultra-low sleep current makes it ideal for space- and energy-constrained designs. When designing with the PIC12LF1840-E/MF, note the 8-DFN package requires careful PCB layout with thermal pad soldering to the ground plane for mechanical reliability and thermal performance. The 'E' temperature grade denotes -40C to +125C operation, making it suitable for industrial and automotive underhood applications. Programming is supported by MPLAB X IDE with PICkit, ICD, or Curiosity development tools. This page synthesizes distributor pricing, drop-in alternatives, application guidance, and engineering design notes that extend beyond the manufacturer datasheet, helping engineers select, source, and integrate the PIC12LF1840-E/MF efficiently.

RFQ যোগাযোগ
PIC12LF1840-E/P - 7KB Flash 8-Bit MCU, 32MHz, XLP | Microchip
PIC12LF1840-E/P

PIC12LF1840-E/P - 7KB Flash 8-Bit MCU, 32MHz, XLP | Microchip

The Microchip Technology PIC12LF1840-E/P is an 8-bit PIC® XLP™ 12F microcontroller featuring 7KB (4K x 14) Flash program memory, 256 bytes of EEPROM, and 256 bytes of SRAM, packaged in an 8-pin PDIP through-hole format. It operates from 1.8V to 3.6V and integrates a 32MHz internal oscillator, delivering up to 32MHz CPU performance (200 ns instruction cycle) while consuming only nanoWatt XLP sleep currents. The part is qualified to the extended (-40C to +125C) temperature grade as denoted by the "-E" suffix. An 8-bit microcontroller (MCU) is a small computer-on-a-chip integrating a CPU, RAM, non-volatile program memory, and peripherals on a single die. Within the broader taxonomy, the PIC12LF1840 belongs to: 8-bit PIC MCU -> enhanced mid-range (XLP) PIC12 family -> PIC PIC12F -> flash microcontroller -> microcontroller -> semiconductor. Its XLP (eXtreme Low Power) technology provides sub-microamp sleep currents, making the PIC12LF1840 a strong choice when battery life dominates the design trade-off. Key differentiating features include four 10-bit ADC channels (with computation), two PWM modules, an EUSART, an MSSP (I2C/SPI) module, two comparators, and a data signal modulator. Peripherals are routed through Microchip's Peripheral Pin Select (PPS) for flexible I/O mapping. Internal oscillator accuracy is +/-2% across voltage and temperature, eliminating the need for an external crystal in most designs. The PIC12LF1840 implements an enhanced mid-range 14-bit instruction set architecture (200 ns per instruction at 32 MHz) with a hardware multiplier and a vectored interrupt controller supporting context save/restore. The integrated Core Independent Peripherals (CIPs) - including the CWG, NCO, and DSM blocks - allow complex signal generation and modulation without CPU intervention, freeing the 8-bit core for application logic. Typical applications include battery-powered sensor nodes, low-end remote controls, LED lighting controllers, IoT edge nodes, and consumer appliances where cost, footprint, and ultra-low sleep current dominate the BOM. The 8-pin PDIP package also makes it a popular choice for hobbyist, education, and breadboard-friendly prototypes using the MPLAB PICkit 5 in-circuit debugger. When designing with this device, observe absolute maximum VDD of 4.0V (operate within 1.8-3.6V) and ensure I/O sink/source ratings (25 mA per pin, 90 mA per port) are respected. Decouple VDD with at least 0.1uF ceramic placed within 5 mm of the supply pin, and leave MCLR unbonded when not used as a reset input. This page synthesizes verified distributor pricing, drop-in pin-compatible alternatives within the PIC12 family, and practical design notes not collected in the manufacturer datasheet.

RFQ যোগাযোগ
PIC12LF1840-E/SN - 8-bit 32MHz MCU 7KB Flash 8-SOIC | Microchip
PIC12LF1840-E/SN

PIC12LF1840-E/SN - 8-bit 32MHz MCU 7KB Flash 8-SOIC | Microchip

The Microchip Technology PIC12LF1840-E/SN is an 8-bit PIC microcontroller from the enhanced mid-range PIC12 family, delivering 32 MHz CPU performance with 7 KB Flash program memory, 256 bytes EEPROM, and 256 bytes RAM in an 8-pin SOIC (SN) package. The 'LF' designation indicates the low-voltage variant with a 1.8 V to 3.6 V operating range, while the 'E' suffix marks the extended industrial temperature grade of -40 °C to +125 °C. This device integrates a 32 MHz internal oscillator, a 4-channel 10-bit ADC, a comparator with selectable voltage reference, an Enhanced Capture/Compare/PWM (ECCP) module, an EUSART with auto-baud, MI2C, SPI, mTouch capacitive sensing, and a Data Signal Modulator (DSM). An 8-bit microcontroller (MCU) is a small, single-chip computer built around a CPU with an 8-bit data path, integrated Flash program memory, RAM, EEPROM, and a rich set of peripherals including timers, ADC, and serial interfaces. Within the broader taxonomy, an 8-bit MCU is a subset of microcontrollers (MCU), which themselves belong to the integrated circuit (IC) hierarchy. PIC microcontrollers use a modified Harvard RISC architecture with a small instruction set optimized for deterministic interrupt response and low-power operation. The PIC12 sub-family targets space-constrained, cost-sensitive, and low-power embedded designs, with the 'LF' grade allowing direct operation from a single lithium cell. Key features include nanoWatt XLP extreme low-power technology with sleep currents as low as 20 nA typical, an active clock tuning mechanism for the internal 32 MHz oscillator, an integrated 5-bit DAC and selectable voltage reference, on-chip ICD debugging support, and 25 mA source/sink capability on I/O pins. The internal 32 MHz oscillator provides instruction cycle times down to 125 ns, eliminating the need for an external crystal in many designs. Architecturally, the PIC12LF1840 uses a 14-bit instruction word enhanced mid-range core with 16 stack levels, self-read/write capable Flash, and an instruction set optimized for compiler efficiency. The Data Signal Modulator allows mixing of peripheral outputs (PWM, comparator, etc.) for advanced signal conditioning without CPU intervention. Typical applications include battery-powered IoT sensor nodes, low-cost remote controls, capacitive touch user interfaces, automotive body electronics (under-the-hood modules needing extended temp), LED lighting controllers with dimming/PWM, and portable consumer devices powered by coin-cell or single Li-ion cells. Design consideration: when migrating from the F-version (PIC12F1840) the L-voltage range must be respected (1.8 V to 3.6 V); programming voltage and ICSP timing parameters should be reviewed against the datasheet. The 8-SOIC package has limited I/O (5 usable), so pin function multiplexing via PPS-equivalent remap must be planned early. This page synthesizes distributor inventory from DigiKey/Mouser, drop-in same-package alternatives, and practical design considerations beyond what the datasheet alone provides.

RFQ যোগাযোগ
PIC12LF1840-I/SN - 8-bit 32MHz XLP MCU, 7KB Flash, 8-SOIC | Microchip
PIC12LF1840-I/SN

PIC12LF1840-I/SN - 8-bit 32MHz XLP MCU, 7KB Flash, 8-SOIC | Microchip

The Microchip Technology PIC12LF1840-I/SN is an 8-bit CMOS flash microcontroller built on the PIC® enhanced mid-range core, operating up to 32 MHz with 7 KB (4K x 14) of Flash program memory and 256 bytes of SRAM, housed in an 8-pin SOIC package. The 'LF' variant targets low-voltage / low-power applications with a supply range down to 1.8 V, complementing the standard PIC12F1840 (2.3–5.5 V) version, and integrates Microchip's eXtreme Low Power (XLP) technology for nanoWatt sleep currents. An 8-bit microcontroller is a small computing-on-a-chip device that executes instructions on 8-bit data words; it sits within the broader taxonomy of microcontroller -> embedded controller -> semiconductor. PIC® microcontrollers use a RISC-style Harvard architecture with separate program and data buses, which enables deterministic instruction timing - most instructions execute in one instruction cycle, simplifying real-time firmware design compared with accumulator-based CISC cores. Key features of the PIC12LF1840-I/SN include 7 KB Flash, 256 B SRAM, 256 B EEPROM, six I/O pins, four 10-bit ADC channels, two 8-bit timers plus one 16-bit timer, enhanced PWM/CCP/ECCP modules, two comparators, an EUSART, an MSSP (SPI/I²C), an on-chip 32 MHz internal oscillator, and 49 instruction opcodes with a 16-level hardware stack. Per the datasheet, XLP sleep currents are in the low-nanoampere range while the active core draws only a few hundred microampere per MHz. Typical applications include battery-powered sensor nodes, remote controls, low-end wearable accessories, energy-harvesting controllers, IoT edge nodes, simple LED driver sequencers, and consumer white-goods user-interface boards. The wide 1.8–3.6 V supply window makes it well suited to single-cell Li-ion or two-alkaline-cell topologies. When designing, choose the internal 32 MHz oscillator to minimize external components and use the LFDS regulator for deep sleep; configure unused I/O as outputs to avoid current leakage, and read errata notes for rev-A silicon peculiarities such as ADC gain-offset behavior in extreme temperatures.

RFQ যোগাযোগ
PIC12LF1840T-I/MF - 8-bit 32MHz 7KB Flash MCU 8-DFN | Microchip
PIC12LF1840T-I/MF

PIC12LF1840T-I/MF - 8-bit 32MHz 7KB Flash MCU 8-DFN | Microchip

The Microchip Technology PIC12LF1840T-I/MF is an 8-bit PIC microcontroller from the PIC® XLP™ 12F family, featuring a 32 MHz enhanced mid-range CPU core, 7 KB (4K x 14) of self-read/write Flash program memory, 256 bytes of EEPROM, and 256 bytes of RAM in an 8-pin 3x3 mm DFN (Dual Flat No-lead) package. The "LF" suffix denotes the wide 1.8V-3.6V low-voltage variant optimized for nanoWatt XLP extreme-low-power operation, making it suitable for battery-powered and energy-harvesting designs. A microcontroller (MCU) is a single-chip computer that integrates a CPU, memory, and peripherals. Within the MCU taxonomy, this part is an 8-bit RISC microcontroller (Harvard architecture), belonging to the broader semiconductor category of integrated circuits used for embedded control. Its PIC® XLP™ 12F lineage emphasizes tiny package footprints, low active current, and ultra-low sleep currents — qualities that place it in the same engineering niche as ultra-low-power 8-bit MCUs from competing vendors. Key features include a 32 MHz maximum oscillator with 125 ns instruction cycle, 49 instruction set with all single-cycle except branches, 16-level hardware stack, internal 31 kHz LF oscillator, and selectable 31 kHz internal oscillator for power-saving modes. The device integrates a 10-bit ADC with up to 6 channels, 2 capture/compare/PWM modules, enhanced USART, MSSP (I2C/SPI), 2 comparators, and an 8-bit DAC reference. nanoWatt XLP technology delivers typical sleep currents under 50 nA, enabling multi-year coin-cell operation. The PIC12LF1840T-I/MF operates across the industrial -40°C to +85°C temperature range (the "I" grade) and ships on tape-and-reel (the "T" suffix) for high-volume SMT assembly. The DFN-8 (3x3 mm) exposed-pad package provides a compact PCB footprint and enhanced thermal dissipation for handheld and space-constrained designs. Typical applications include IoT sensor nodes, remote control transmitters, low-power wireless end nodes, battery monitoring ICs, smart wearables, and consumer electronics that require long battery life in a sub-1 cm² footprint. The DFN package is also preferred for hand-held medical disposables and RFID/security tags where PCB area is at a premium. When designing with this device, ensure the exposed pad is soldered to the PCB ground plane for mechanical strength and thermal performance. Because the LF variant operates only up to 3.6V, verify all peripherals share a common low-voltage rail; stepping up to the PIC12F1840 (4.0V-5.5V) variant is recommended for 5V systems. This page synthesizes distributor stock and pricing, pin-compatible drop-in alternatives from the same Microchip PIC12 family, and practical design notes not found in the manufacturer datasheet — providing a one-stop engineering reference for the PIC12LF1840T-I/MF.

RFQ যোগাযোগ
PIC12LF1840T-I/RF - 8-bit 32MHz XLP MCU 7KB Flash | Microchip
PIC12LF1840T-I/RF

PIC12LF1840T-I/RF - 8-bit 32MHz XLP MCU 7KB Flash | Microchip

The Microchip Technology PIC12LF1840T-I/RF is an 8-bit PIC microcontroller from the PIC12F series, featuring the eXtreme Low Power (XLP) technology, 7KB (4K x 14) of Flash program memory, and 256 bytes of RAM. Housed in an 8-pin UDFN (also referred to as 8-DFN, 3x3 mm) package with an exposed thermal pad, it operates at up to 32MHz internal clock speed and supports a supply voltage range of 1.8V to 3.6V, making it ideal for battery-powered applications. The device integrates six I/O pins, enhanced mid-range core, 10-bit ADC, comparators, PWM modules, and internal oscillator. A PIC microcontroller (MCU) is a compact, programmable integrated circuit that combines a CPU, non-volatile Flash program memory, volatile RAM, and configurable peripherals on a single silicon die. Within Microchip's taxonomy it sits below the dsPIC DSC family and the 16-bit and 32-bit MCU families; PIC microcontrollers are widely used in cost- and power-sensitive embedded designs where deterministic interrupt response and rich peripheral integration matter more than raw compute throughput. Key features of this part include XLP technology for sub-microamp sleep currents, an internal 32MHz oscillator with PLL, multiple communication peripherals including EUSART, MSSP (SPI/I2C), and on-chip 10-bit ADC with up to 4 channels. The 8-pin UDFN package offers a compact 3x3 mm footprint with exposed pad, while the operating temperature range of -40C to +85C supports industrial-grade deployments. Typical applications include wearable electronics, IoT sensor nodes, battery-powered remote controls, low-power wireless transmitters (the LF variant supports 1.8V-3.6V operation needed by RF companion chips), and small-form-factor consumer devices. The integrated peripherals reduce BOM cost by eliminating external ADC, comparator, or oscillator components. When designing with this MCU, ensure the exposed pad (pin 9 / EP) is properly soldered to the PCB ground plane to meet the published thermal resistance specification. For code development, Microchip's MPLAB X IDE with XC8 compiler and PICkit 5 in-circuit debugger are the canonical tool chain, and ICSP programming is supported through dedicated PGx and PGDx pins. This page synthesizes distributor pricing tiers, drop-in same-package alternatives, and practical design notes that go beyond the manufacturer datasheet itself, giving the engineer a single decision-ready reference for selecting and sourcing the PIC12LF1840T-I/RF.

RFQ যোগাযোগ
PIC12LF1840T-I/SN - 8-bit XLP MCU, 7KB Flash, 32MHz | Microchip
PIC12LF1840T-I/SN

PIC12LF1840T-I/SN - 8-bit XLP MCU, 7KB Flash, 32MHz | Microchip

The Microchip PIC12LF1840T-I/SN is an 8-bit PIC microcontroller from the PIC12F series featuring eXtreme Low Power (XLP) technology, 7KB (4K x 14) of Flash program memory, 256 bytes of EEPROM, and 256 bytes of SRAM, all housed in an 8-pin SOIC (SN) package supplied on tape and reel. The device runs at up to 32 MHz from its internal oscillator and operates across a wide 1.8V to 3.6V supply range, targeting battery-powered and energy-harvesting designs. An 8-bit microcontroller (MCU) is a small single-chip computer that integrates a CPU, non-volatile program memory, working RAM, and peripheral interfaces onto a single silicon die. Within the system hierarchy, MCUs sit between discrete logic and full microprocessors, occupying the role of programmable decision-makers in embedded systems. The 8-bit PIC12 family in particular targets compact, cost-sensitive applications where 6 or fewer I/O pins suffice, with variants like the PIC12LF1840 optimized for ultra-low standby current. Key features of the PIC12LF1840 include an enhanced mid-range core with 49 instructions and a 16-level hardware stack, four 10-bit ADC channels with selectable voltage reference, an enhanced Capture/Compare/PWM (ECCP) module, a comparator with selectable voltage reference, an integrated mTouch capacitive sensing module, and a Data Signal Modulator (DSM). Communication interfaces cover MI2C, SPI, and EUSART with auto-baud. Per I/O pin, the device can source or sink up to 25 mA, simplifying direct LED or transistor drive without external buffers. Architecturally, the device pairs a single-cycle ALU with self-read/write Flash, supporting field firmware updates and EEPROM emulation. The internal 32 MHz oscillator is factory-calibrated and selectable down to 31 kHz for low-power timing, while the nanoWatt XLP sleep modes drop current consumption into the nanoampere range - critical for coin-cell and energy-harvesting applications. Typical applications include battery-powered sensor nodes, IoT edge devices, capacitive touch user interfaces, LED lighting controllers, and low-cost consumer electronics. The combination of small footprint, low power, and rich peripherals also makes it suitable for automotive body electronics subsystems and industrial control front-ends. When designing with this part, prioritize decoupling close to VDD, keep analog traces short, and use the ICSP pins (RA0/RA1) carefully to avoid conflicts with high-impedance analog channels. The tape-and-reel -T suffix is intended for high-volume assembly. This page synthesizes verified distributor pricing, drop-in SOIC-8 alternatives, and practical design notes not aggregated on any single manufacturer or distributor page.

RFQ যোগাযোগ
PIC14000-04/SO - 8-Bit Mixed Signal MCU, 7KB OTP, 28-SOIC
PIC14000-04/SO

PIC14000-04/SO - 8-Bit Mixed Signal MCU, 7KB OTP, 28-SOIC

The Microchip PIC14000-04/SO is an 8-bit CMOS OTP-based mixed-signal microcontroller in the PIC14 family, integrating a 4 MHz RISC core with 7 KB (4K x 14) of OTP program memory and 192 bytes of SRAM in a 28-pin SOIC (0.295 inch / 7.50 mm width) package. The device executes instructions in a single 200 ns cycle (except program branches, which take two cycles) from a compact 35-instruction word set, and provides 20 digital I/O pins plus a rich analog front-end tailored for sensor and signal-conditioning tasks. Background: An 8-bit mixed-signal microcontroller is a single-chip computer that combines a CPU, non-volatile program memory (here, One-Time Programmable EPROM), RAM, digital I/O, and on-chip analog peripherals such as ADCs, DACs, references, and current sources. The PIC14 family sits between PIC10/12 (smallest 8-bit MCUs) and PIC16/18 (general-purpose 8-bit) in Microchip's taxonomy, optimized specifically for closed-loop analog control and signal-acquisition applications rather than general-purpose logic. Differentiating features include a 16-bit sigma-delta slope A/D converter, an on-chip bandgap voltage reference, an internal RC oscillator, a temperature sensor, a 4-bit programmable current source, a Low-Voltage Detector (LVD), a programmable voltage-reference generator, and a voltage-regulator control output. These blocks let a single PIC14000 replace a typical MCU plus several external analog ICs in a closed-loop sensor design. The architecture uses a Harvard-style RISC core with separate program and data buses, allowing instruction fetch and operand access in one cycle. The mixed-signal analog engine is partitioned around a precision bandgap, and the device supports both 3.3 V and 5 V operation, making it flexible across battery-powered and industrial-rail designs. Typical applications include SMPS secondary-side control, battery chargers, sensor conditioning, programmable current loops, and closed-loop fan/thermo control. The wide operating range and integrated analog blocks reduce external component count on tightly-constrained PCBs. Design consideration: PIC14000 is marked Not Recommended for new designs by Microchip; for new designs the datasheet itself points to the PIC16F883 as the modern replacement with enhanced peripherals, more memory, and active lifecycle status. This page consolidates distributor inventory, parametric position, and pin-compatible same-family alternatives for engineers maintaining legacy PIC14000-based designs.

RFQ যোগাযোগ
PIC14000-04/SS - 4MHz 8-bit Mixed Signal MCU 28-SSOP | Microchip
PIC14000-04/SS

PIC14000-04/SS - 4MHz 8-bit Mixed Signal MCU 28-SSOP | Microchip

The Microchip Technology PIC14000-04/SS is an 8-bit CMOS OTP-based mixed-signal microcontroller in a 28-pin SSOP package, integrating a 200 ns instruction-cycle RISC core with a 16-bit sigma-delta A/D converter, 4-bit programmable current source, bandgap voltage reference, internal temperature sensor, LVD (low-voltage detector), voltage-regulator control output, and a programmable reference generator. It delivers 4 MHz maximum clock speed, 7 KB (4K x 14) of OTP program storage, 192 bytes of data RAM, and 20 digital I/O lines, with an operating supply voltage of 2.7 V to 6.0 V across the commercial 0C to +70C range. According to the Microchip PIC14000 datasheet DS40122, the device is a member of the PIC® 14 family of mixed-signal controllers targeting power-supply monitoring and battery-charger analog front-ends. A mixed-signal microcontroller (MSMCU) combines a traditional digital MCU core with high-precision analog peripherals on a single die. In system hierarchies, the PIC14000 belongs to: MCU -> microcontroller -> embedded controller -> semiconductor IC. The PIC® 14 family was specifically designed for closed-loop analog control applications where a discrete MCU plus op-amp + ADC + DAC chain would be too large or expensive. Key differentiating features of the PIC14000-04/SS include its integrated 16-bit sigma-delta A/D converter (eliminating an external precision ADC), a programmable constant-current source for sensor excitation, on-chip bandgap reference with internal temperature sensor for self-monitoring, and LVD plus a voltage-regulator control PWM output that allows the device to act as the brain of a closed-loop switching supply. The 35-instruction RISC core is RISC architecture with Harvard bus and 200 ns instruction execution at 4 MHz. Typical applications include switching power supply control (PFC, battery chargers), closed-loop battery chargers, sensor signal conditioning, programmable current sources, and standalone analog front ends where a low pin-count mixed-signal MCU replaces a larger MCU + external ADC. When designing with this device, ensure the OTP programming step is budgeted into the production flow, as one-time-programmable memory cannot be field-updated. Decouple VDD with a 100 nF ceramic capacitor close to the pin and provide adequate bulk capacitance for the analog reference. This page synthesizes Microchip product-page information, distributor pricing (Mouser, DigiKey), drop-in same-package alternatives from the PIC14000 product family, and practical design notes that go beyond the manufacturer datasheet.

RFQ যোগাযোগ
PIC14000-04I/SO - 8-Bit 4MHz Mixed-Signal MCU | Microchip | 28-SOIC
PIC14000-04I/SO

PIC14000-04I/SO - 8-Bit 4MHz Mixed-Signal MCU | Microchip | 28-SOIC

The Microchip PIC14000-04I/SO is a 28-pin 8-bit mixed-signal microcontroller based on the PIC RISC architecture, featuring a 4 MHz CPU, 7 KB (4K x 14) OTP program memory and 192 bytes of SRAM, housed in an industrial-grade 28-SOIC package. The /SO suffix denotes the SOIC surface-mount package with industrial temperature grade (-40C to +85C). A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory, working RAM, and programmable I/O peripherals onto one silicon die. PIC MCUs use a RISC-based Harvard architecture, which separates program and data memory paths to allow simultaneous instruction fetch and operand access. The PIC14xx family extends this architecture with on-chip analog peripherals such as an 8-bit ADC, voltage reference, comparators, and a switched-capacitor bandgap, making the PIC14000 specifically a 'mixed-signal controller' rather than a pure digital MCU. Key features include 35 single-word instructions, all executing in a single cycle except program branches (which take two cycles), 200 ns instruction execution time at 20 MHz, 20 programmable digital I/O pins, 5 external interrupts, 6 internal interrupts, and an 8-bit ADC with 8 channels. The device supports multiple power-saving SLEEP modes and wakes via interrupt or reset. The 28-SOIC package provides 0.295 inch (7.50 mm) body width suitable for hand-soldering and reflow profiles in industrial designs. The PIC14000 architecture combines a RISC core with integrated analog blocks: an 8-bit successive-approximation ADC, an on-chip voltage regulator, programmable gain stages, and charge-balancing measurement circuitry. This analog integration allows direct interface to sensors such as thermocouples and bridge-type transducers without external signal conditioning. Typical applications include battery charging controllers, battery capacity monitoring, smart battery management, precision data logging, and standalone sensor signal conditioning. The device's combination of low-power SLEEP modes and on-chip analog makes it a fit for portable and energy-harvesting products where PCB area and BOM cost dominate. When designing with this part, note that the PIC14000 is OTP (one-time programmable) and is marked by Microchip as 'Not Recommended for new designs' (NRND). For new designs, select PIC16F or PIC18 families. The /SO package is compatible with standard SOIC-28 footprints but requires careful thermal and EMI layout around the analog inputs.

RFQ যোগাযোগ
PIC14000-20/SS - 8-Bit 20MHz Mixed-Signal MCU, 7KB OTP, 28-SSOP | Microchip
PIC14000-20/SS

PIC14000-20/SS - 8-Bit 20MHz Mixed-Signal MCU, 7KB OTP, 28-SSOP | Microchip

The Microchip PIC14000-20/SS is an 8-bit mixed-signal CMOS microcontroller built on the PIC14 architecture, integrating a high-performance RISC CPU with on-chip analog peripherals in a 28-pin SSOP package. Key headline parameters: 20 MHz maximum clock, 7 KB (4K x 14) OTP program memory, 192 bytes RAM, and 20 digital I/O pins. The device is specified for commercial-grade 0C to +70C operation. A mixed-signal microcontroller combines a digital microcontroller core with integrated analog peripherals such as ADCs, DACs, voltage references, and current sources on a single silicon die. This category, often called a Programmable Mixed Signal Controller (PMSC), sits within the broader hierarchy of microcontroller -> embedded controller -> semiconductor IC. Mixed-signal MCUs are widely used in closed-loop control, sensor signal conditioning, and power-management applications where a few analog channels are needed without the cost of a separate ADC chip. The PIC14000 integrates a 16-bit Sigma-Delta slope ADC, an on-chip temperature sensor, a bandgap voltage reference, a 4-bit programmable current source, a programmable reference generator, a low-voltage detector (LVD), and a voltage regulator control output. This analog integration reduces bill-of-materials count in closed-loop systems. The PIC RISC architecture executes instructions in 200 ns at 20 MHz, with all instructions single-cycle except program branches (two-cycle), and only 35 single-word instructions to learn. Typical applications include SMPS primary-side control, battery chargers, sensor signal conditioning, programmable current sources, industrial process controllers, and intelligent power management modules. The combination of OTP program memory, internal oscillator, and integrated voltage regulation makes the PIC14000 suited for cost-sensitive industrial designs. Designers should note that the PIC14000 is flagged as Not Recommended for new designs by Microchip. Existing designs may continue using the part, but new projects should evaluate PIC16 or PIC18 alternatives from Microchip's current portfolio. Decoupling, analog ground isolation, and adequate PCB thermal relief around the SSOP-28 pad are recommended for the 28-SSOP package. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ যোগাযোগ
PIC14000-20I/SP - 8-Bit 20MHz Mixed-Signal MCU | Microchip
PIC14000-20I/SP

PIC14000-20I/SP - 8-Bit 20MHz Mixed-Signal MCU | Microchip

The Microchip Technology PIC14000-20I/SP is a 28-pin programmable mixed-signal controller from the PIC® 14 family, integrating an 8-bit RISC CPU core with analog peripherals in a 28-SPDIP through-hole footprint. The device executes instructions at 20 MHz with a 200 ns instruction cycle, providing 7 KB (4K x 14) of OTP program memory, 192 bytes of SRAM, and 20 digital I/O lines. The PIC14000 belongs to the broader PIC microcontroller family (8-bit MCU -> microcontroller -> embedded controller -> semiconductor IC). As an 8-bit mixed-signal MCU it combines a CPU, on-chip analog, and power-management peripherals in a single die, eliminating the need for external ADC and reference ICs in cost-sensitive analog control loops. Key features include an on-chip temperature sensor, a bandgap voltage reference, an internal RC oscillator, a Sigma-Delta slope A/D converter, a 4-bit programmable current source, an LVD (Low Voltage Detector), a voltage-regulator control output, and a programmable reference generator. The 35-instruction RISC ISA keeps code authoring simple, and only program-branch instructions take two cycles; every other single-word instruction executes in one cycle. The OTP program memory supports low-volume production, while the 192-byte SRAM and 8 hardware registers suit small closed-loop control tasks. The integrated Sigma-Delta slope A/D, current source, and bandgap reference let designers build closed-loop analog control (e.g., battery chargers, temperature regulators, current sources) with no external ADC chip. The on-chip LVD and regulator-control output simplify power-supply supervision and switching-converter interface, while the integrated analog blocks reduce BOM count and PCB area. Typical applications include battery chargers, switched-mode power supply controllers, temperature regulators, programmable current sources, smart battery management, and industrial process-control loops where the integrated analog front-end eliminates a separate ADC IC. When designing with this part, allocate OTP programming time during prototyping and verify the Sigma-Delta slope converter's sampling-rate limit against the closed-loop bandwidth you require; for higher throughput consider an external SAR ADC or migrate to PIC16/18 families. This page synthesizes distributor pricing, drop-in same-package alternatives, and engineering notes beyond the Microchip datasheet summary, giving buyers and hardware engineers a single decision-ready reference.

RFQ যোগাযোগ
PIC14000-20I/SS - 7KB EPROM 8-bit MCU | Microchip SSOP-28
PIC14000-20I/SS

PIC14000-20I/SS - 7KB EPROM 8-bit MCU | Microchip SSOP-28

The Microchip Technology PIC14000-20I/SS is an 8-bit CMOS OTP-based mixed-signal microcontroller in a 28-pin SSOP package. Per the manufacturer datasheet, the device integrates a 7 KB EPROM program memory (4K x 14), 192 bytes of RAM, and 20 digital I/O lines, executing instructions in 200 ns at a 20 MHz clock. It belongs to Microchip's PIC® 14 product family and was specifically engineered for programmable mixed-signal control applications. A microcontroller (MCU) is a single-chip computer that contains a processor core, memory, and programmable I/O peripherals. The PIC architecture uses a RISC-based Harvard design with separate program and data paths, allowing most instructions to execute in one instruction cycle. The PIC14 family sits between the PIC16 and PIC12F sub-families in Microchip's lineup, targeting applications that need more analog integration than baseline PIC16 devices while keeping the pin count modest. Key features of the PIC14000-20I/SS include an on-chip temperature sensor, a bandgap voltage reference, an internal oscillator, a Sigma-Delta slope A/D converter, a 4-bit programmable current source, a low-voltage detector (LVD), a voltage-regulator control output, and a programmable reference generator. This integrated analog front end lets a single chip replace several external analog components, which is the defining characteristic of the PIC14 series. The industrial-grade operating range is -40 °C to +85 °C, suitable for factory and outdoor equipment. Typical applications include battery chargers, smart battery management, sensor conditioning, switching power supply control loops, and process control transmitters. Each application exploits the combination of the Sigma-Delta converter (for high-resolution slow signals like thermistors), the programmable current source (for 4-20 mA loop excitation), and the bandgap reference (for ratiometric measurements). When designing with this device, allocate oscillator configuration time before A/D conversion begins, and follow the datasheet's decoupling guidance (typically 0.1 µF VDD pin capacitor plus bulk capacitance) to keep the Sigma-Delta converter noise floor low. The PIC14000 is now in Microchip's "Not Recommended for new designs" status, so designers of new products should evaluate the modern PIC16F or PIC18 successors.

RFQ যোগাযোগ
PIC14000/JW - 8-Bit 4MHz Mixed-Signal MCU, 7KB EPROM, 28-CerDIP
PIC14000/JW

PIC14000/JW - 8-Bit 4MHz Mixed-Signal MCU, 7KB EPROM, 28-CerDIP

The Microchip Technology PIC14000/JW is an 8-bit programmable mixed-signal microcontroller IC operating at 4 MHz with 7KB (4K x 14) UV-erasable EPROM program memory, 192 bytes of RAM, and 20 I/O pins in a 28-pin ceramic DIP (CerDIP) windowed package. It is built around the PIC14 architecture using a RISC core with only 35 single-word instructions and 200 ns instruction execution time. A microcontroller (MCU) is a single-chip computer that integrates a CPU, memory, and peripheral interfaces on one die. The PIC family of microcontrollers uses a Harvard architecture RISC core, where program and data memories are physically separate, enabling faster instruction fetch and deterministic execution. The PIC14 sub-family is a programmable mixed-signal line that adds analog peripherals (slope A/D, bandgap reference, programmable current source, LVD, voltage regulator control output) to the standard digital PIC core, making it suitable for sensor signal conditioning and closed-loop control. Key features of the PIC14000/JW include an 8-channel slope A/D converter for low-frequency analog measurement, a 4-bit programmable current source for sensor excitation, an internal oscillator, an on-chip temperature sensor, a bandgap voltage reference, a Low-Voltage Detector (LVD), and a voltage regulator control output. The device supports 6 internal interrupts and 5 external interrupts, and operates from 4.5V to 5.5V across the commercial temperature range. The JW suffix indicates a windowed ceramic package, which allows UV erasure for development and reprogramming of the EPROM. Compared with OTP and Flash variants, the JW package is intended for prototyping, education, and low-volume engineering use where program memory must be repeatedly re-written. Typical applications include industrial sensor signal conditioning, battery charging controllers, closed-loop fan/thermostat control, and mixed-signal front-ends for instrumentation. The device is also widely used in engineering education because the JW windowed package supports repeated erase/program cycles for code experimentation. When designing with the PIC14000/JW, note that the ceramic DIP package is through-hole only, and the EPROM window must be covered during operation to prevent accidental UV erasure from ambient light. Program memory is limited to 4K words of 14-bit instructions, so code must be optimized for footprint. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found on the manufacturer product page alone.

RFQ যোগাযোগ
PIC14000T-04/SO - 8-Bit 4MHz Mixed-Signal MCU, 7KB OTP, 28-SOIC
PIC14000T-04/SO

PIC14000T-04/SO - 8-Bit 4MHz Mixed-Signal MCU, 7KB OTP, 28-SOIC

The Microchip Technology PIC14000T-04/SO is a member of the PIC® 14 family of 8-bit CMOS mixed-signal microcontrollers, integrating on-chip analog peripherals around a 4 MHz RISC core with 7 KB (4K x 14) of One-Time-Programmable (OTP) program memory. Housed in a 28-pin SOIC (SO) package on tape-and-reel, the part is rated for the commercial temperature grade and operates from 3.3 V / 5 V rails with 200 ns instruction execution and a 35-word instruction set. A microcontroller (MCU) is a single-chip computer that integrates a CPU, program memory, data RAM, and a set of peripherals; the PIC14 line extends that template with analog peripherals such as a sigma-delta A/D slope converter, on-chip temperature sensor, bandgap voltage reference, 4-bit programmable current source, low-voltage detector (LVD), voltage regulator control output, and programmable reference generator. The PIC14000 thus sits in the hierarchy: MCU -> 8-bit microcontroller -> mixed-signal MCU -> PIC14 family -> CMOS OTP-based RISC. Key differentiating features include an on-chip temperature sensor and bandgap reference that eliminate external analog conditioning, an internal oscillator that reduces external component count, and a 4-bit programmable current source targeted at sensor excitation. The 7 KB OTP allows field-programmed code, while 35 single-word instructions keep the learning curve minimal for code development. The 28-SOIC package supports hand-soldering and standard 0.05-inch-pitch PCB footprints, suiting both prototyping and small-volume production. Architecturally, the PIC14000 combines a Harvard RISC core with sigma-delta analog front-end, achieving A/D conversion by oversampling rather than using a conventional successive-approximation register (SAR). The 200 ns instruction cycle (5 MHz effective clock / 4 MHz oscillator with internal 4x divider) gives roughly 5 MIPS throughput, and the 35-word instruction set is fully orthogonal. Industrial-grade silicon supports reliable operation in harsh environments. Typical applications include battery chargers with on-chip current source and temperature-compensated voltage reference, sensor-conditioning front-ends (thermocouple/RTD excitation), closed-loop fan-speed and motor-speed controllers, smart battery management with LVD-driven cutoff, and low-cost mixed-signal instrumentation. The 28-SOIC variant suits through-hole-style hand rework and 0.05" prototype boards. When designing with the PIC14000T-04/SO, allocate code space carefully within the 7 KB OTP budget, since OTP cannot be erased. Add a 0.1 uF decoupling capacitor close to VDD, and route the MCLR/VPP pin through a 10 kohm pull-up to allow in-circuit serial programming. This page synthesizes distributor pricing, drop-in PIC14000 family alternatives, application reference circuits, and practical design notes not consolidated on the manufacturer product page or distributor listings.

RFQ যোগাযোগ
PIC14000T-04/SS - 7KB OTP 8-Bit MCU 20 I/O 28-SSOP | Microchip
PIC14000T-04/SS

PIC14000T-04/SS - 7KB OTP 8-Bit MCU 20 I/O 28-SSOP | Microchip

The Microchip Technology PIC14000T-04/SS is an 8-bit CMOS mixed-signal microcontroller based on Microchip's PIC architecture, offering 7KB (4K x 14) of One-Time Programmable (OTP) program memory, 192 bytes of RAM, and 20 digital I/O pins in a 28-pin SSOP package. The core runs at 4 MHz with a 200 ns instruction execution time, and the part is supplied in Tape & Reel (T) packaging for high-volume assembly lines. A PIC microcontroller is a RISC-based 8-bit microcontroller family manufactured by Microchip Technology, widely used in embedded control applications. It belongs to the broader hierarchy of microcontrollers -> microprocessors -> integrated circuits -> semiconductors. PIC MCUs are characterized by their Harvard architecture, single-cycle instruction execution (except branches), and a small instruction set (typically 35 single-word instructions for the mid-range family), making them popular for low-cost, low-power, deterministic control tasks. Key features of the PIC14000T-04/SS include 7KB OTP program memory, 192 bytes of RAM, 20 I/O pins, an integrated Slope A/D converter (a unique analog front-end in the PIC14xxx family), a commercial operating temperature range of 0 C to +70 C, and surface-mount SSOP-28 packaging. The architecture provides 14-bit wide instructions and supports all single-cycle instructions except program branches (two cycles), giving predictable timing for real-time control loops. The PIC14000 family is differentiated from standard mid-range PICs by its mixed-signal capabilities, including the on-chip Slope A/D converter that allows direct interfacing with resistive sensors (thermistors, RTDs, bridge sensors) without external ADC components. This makes it particularly suitable for sensor-conditioning applications where PCB real estate and BOM cost are critical. Typical applications include industrial sensor signal conditioning, battery chargers, SMPS control loops, HVAC damper/actuator control, and consumer appliance controllers. The integrated Slope A/D simplifies analog front-end design in cost-sensitive embedded products. When designing with this device, note that the OTP program memory is one-time programmable - firmware must be fully verified before production programming. The 28-SSOP package is hand-solderable with care but is best assembled by reflow; the commercial 0 C to +70 C temperature range limits the part to indoor and benign-environment applications. This page synthesizes distributor pricing, 28-SSOP drop-in alternatives, and practical design notes not found in the standalone manufacturer datasheet.

RFQ যোগাযোগ
PIC14000T-04I/SO - 8-bit Mixed Signal MCU 7KB OTP | Microchip
PIC14000T-04I/SO

PIC14000T-04I/SO - 8-bit Mixed Signal MCU 7KB OTP | Microchip

The Microchip Technology PIC14000T-04I/SO is an 8-bit CMOS OTP-based mixed-signal microcontroller from the PIC14 family, delivering 4 MHz performance in a 28-pin SOIC (SO) package. Built on Microchip's PIC RISC architecture with only 35 single-word instructions, the device executes instructions in 200 ns and most instructions complete in a single oscillator cycle, except program branches which take two cycles. The 'T' suffix denotes tape-and-reel packaging, while 'I' indicates the industrial temperature grade (-40C to +85C), and the '04' speed designation corresponds to the 4 MHz oscillator. Mixed-signal microcontrollers integrate analog and digital peripherals on a single die, eliminating the external ADC, DAC, op-amps, and comparator circuitry that traditional 8-bit MCUs require. The PIC14000 family belongs to Microchip's PIC14 sub-family and sits between the baseline PIC10/12/16 families and the mid-range PIC18 family in the taxonomy, specifically targeting motor control, power conversion, and analog signal conditioning where on-chip comparators, PWMs, and ADCs reduce BOM cost and PCB area. Key features include 7 KB (4K x 14) of One-Time-Programmable (OTP) program memory, 192 bytes of RAM, 20 digital I/O pins, an integrated multi-channel 8-bit ADC, operational amplifiers, comparators, and PWM modules. Supply voltage spans 4.5V to 5.5V (with some references showing 3.3V/5V operation), making the part compatible with both 3.3V and 5V system designs. The wide instruction set, RISC architecture, and integrated analog peripherals enable compact, deterministic code for closed-loop control applications. The PIC14000 architecture combines a Harvard-bus RISC core with on-chip analog blocks - including programmable gain amplifiers and comparators - tightly coupled to the digital engine. This integration allows real-time feedback control without CPU overhead from external SPI or I2C peripherals, improving control-loop latency for motor-drive and switch-mode power applications. Typical applications include switched-mode power supplies (SMPS), uninterruptible power supplies (UPS), battery chargers, motor control (BLDC and stepper), fluorescent and HID ballasts, and analog signal conditioning front-ends. The integrated analog front-end also suits industrial sensor signal chains where 8-bit resolution is acceptable. When designing with this device, allocate OTP programming time during manufacturing because OTP cannot be re-programmed in-circuit. Provide adequate decoupling (0.1 uF ceramic plus 10 uF bulk) on VDD, and route analog references (VREF+, VREF-) with ground guarding to preserve ADC accuracy. Industrial temperature parts are recommended for outdoor or factory-floor deployments. This page synthesizes distributor pricing, drop-in alternates within the PIC14 family, and practical design notes beyond what the manufacturer datasheet alone provides.

RFQ যোগাযোগ
PIC14000T-04I/SS - 8-bit 4MHz 7KB OTP MCU 28-SSOP | Microchip
PIC14000T-04I/SS

PIC14000T-04I/SS - 8-bit 4MHz 7KB OTP MCU 28-SSOP | Microchip

The Microchip Technology PIC14000T-04I/SS is an 8-bit CMOS mixed-signal microcontroller based on the PIC14 architecture, delivering 4 MHz (200 ns instruction cycle) CPU performance with 7 KB (4K x 14) of One-Time Programmable (OTP) program memory, 192 bytes of RAM, and 20 general-purpose I/O pins in a 28-pin SSOP package. The "T" suffix denotes tape-and-reel packaging, the "04" denotes the 4 MHz maximum clock, the "I" denotes the industrial temperature grade (-40C to +85C), and the "/SS" suffix denotes the 28-SSOP package. What is a PIC Mixed-Signal Microcontroller? A mixed-signal microcontroller integrates an analog front-end (typically 8- or 10-bit ADC, comparators, op-amps, voltage references, and current sources) alongside a digital CPU core on a single die. The PIC14000 was Microchip's first dedicated SMPS (switched-mode power supply) and power-conversion controller MCU, with the analog peripherals specifically designed for closed-loop digital control of buck, boost, flyback, and SEPIC converters. Key features include a 14-bit instruction word optimized for compact code density (only 35 single-word instructions to learn), all single-cycle except program branches which take two cycles, and integrated peripherals that include an 8-bit ADC, dual comparators, and PWM modules suitable for digital power conversion loops. The 28-SSOP surface-mount package has a 0.209" (5.30 mm) body width and supports industrial-grade operation across -40C to +85C. Architecturally, the PIC14000 combines a RISC-style Harvard CPU with purpose-designed SMPS peripherals, allowing firmware engineers to implement digital compensation, soft-start, and adaptive dead-time control for high-frequency switching converters. The OTP program memory is one-time programmable in volume production but is also windowed or flash-reprogrammable on related die variants, supporting iterative development. Typical applications include digitally controlled switch-mode power supplies, battery chargers, LED drivers with dimming control, DC-DC converter primary-side controllers, power-factor correction (PFC) stages, and industrial motor-control auxiliary rails. The 20 GPIO pins are sufficient for synchronous rectifier drive, fault signaling, and I2C/SPI-based telemetry to a host controller. When designing with this device, allocate the 192-byte RAM carefully; digital compensation loops, look-up tables, and ADC averaging can exhaust it quickly. Use the OTP programming window during prototyping to iterate the firmware, then move to volume OTP programming for production. Per the Microchip PIC14000 family datasheet, derating of the internal oscillator is required for SMPS loops sensitive to timing jitter. This page synthesizes distributor pricing, drop-in SSOP-28 alternatives, and SMPS-loop design considerations not found in the standalone manufacturer datasheet.

RFQ যোগাযোগ
PIC14000T-20/SO - 8-bit 20MHz OTP MCU, 7KB | Microchip
PIC14000T-20/SO

PIC14000T-20/SO - 8-bit 20MHz OTP MCU, 7KB | Microchip

The Microchip Technology PIC14000T-20/SO is an 8-bit RISC mixed-signal microcontroller from the PIC14 family, operating at 20 MHz with 7 KB (4K x 14) of One-Time Programmable (OTP) program memory and 192 bytes of RAM, housed in a 28-pin SOIC (SO) wide-body package. It executes instructions in 200 ns and is supported by a compact 35-instruction set, balancing throughput with programming simplicity. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory, RAM, and peripherals. Within the wider taxonomy, the PIC14000 belongs to the 8-bit MCU family -> RISC architecture -> Harvard architecture -> PIC14 series -> mixed-signal microcontroller, ultimately classified as an embedded semiconductor. Its mixed-signal heritage distinguishes it from general-purpose 8-bit MCUs because it ships with on-chip analog peripherals tailored for sensor-driven and signal-conditioning applications. Key features include 20 I/O pins, 20 MHz maximum clock speed, 4.5 V to 5.5 V single-supply operation, 7 KB OTP program memory, 192 x 8 bytes of data RAM, and integrated peripherals such as an 8-channel 8-bit ADC, comparators, and a slope ADC. The wide-body 28-SOIC package (0.295 in / 7.50 mm width) supports standard surface-mount reflow processes and is fully RoHS compliant. The architecture follows Microchip's RISC design with a 14-bit instruction word for code density. Technically, the PIC14000T-20/SO is built on CMOS technology with 200 ns instruction execution and uses OTP memory for program storage. The integrated mixed-signal peripherals - including op-amps, comparators, and timers - allow direct interface to analog sensors without extensive external analog components. The device targets cost-sensitive, mixed-signal applications where integration reduces BOM count. Typical applications include smoke detectors, security systems, sensor signal conditioning, battery chargers, motor control feedback loops, and small industrial control boards. The 20 MHz clock and on-chip analog peripherals make it well-suited for systems that must process analog signals in real time without a dedicated external ADC. When designing with this MCU, pay attention to the OTP memory constraint - once programmed the part cannot be erased, so production-grade firmware verification must be completed on a windowed (UV-erasable) or flash-based prototype before committing. Ensure that the 28-SOIC wide-body footprint matches your PCB land pattern, and that decoupling and ADC reference design follow Microchip's mixed-signal layout guidelines. This page synthesizes distributor pricing, same-family drop-in alternatives, and practical mixed-signal design notes not found in the manufacturer datasheet alone, helping engineers select and source the part with confidence.

RFQ যোগাযোগ
PIC14000T-20/SS - 8-Bit 20MHz 7KB OTP MCU | Microchip
PIC14000T-20/SS

PIC14000T-20/SS - 8-Bit 20MHz 7KB OTP MCU | Microchip

The Microchip Technology PIC14000T-20/SS is an 8-bit PIC microcontroller built on the PIC14 architecture, featuring a 20MHz maximum clock speed, 7KB (4K x 14) of One-Time Programmable (OTP) program memory, and 192 bytes of RAM, all integrated into a 28-pin SSOP package supplied on tape and reel. Designed for mixed-signal applications, it executes instructions in 200ns (single cycle, except program branches which are two cycles), supports only 35 single-word instructions, and is manufactured in CMOS for low power consumption. A microcontroller (MCU) is a single-chip computer containing a CPU core, program memory, data RAM, and integrated peripherals such as timers, A/D converters, and communication interfaces. The PIC14 family sits between the baseline PIC10/12 series and the mid-range PIC16 family, offering a RISC instruction set, deterministic execution timing, and OTP or flash program memory for embedded control. Microcontrollers serve as the decision-making core of virtually every embedded product, replacing discrete logic with software-defined behavior. Key features of the PIC14000T-20/SS include the 8-bit PIC RISC core, 7KB OTP program memory suitable for production-volume firmware, 192 bytes of data RAM for variable storage, a 20MHz clock providing 5 MIPS throughput, and an industrial-grade operating temperature range suitable for commercial embedded designs. The SSOP-28 package (5.30mm body width) provides a compact surface-mount footprint compatible with standard 0.65mm-pitch land patterns. From a technical depth perspective, the PIC14000 integrates mixed-signal peripherals including A/D conversion channels and analog comparators alongside the digital core, making it suitable for sensor-interface and control applications. The OTP memory allows one-time programming during manufacturing, offering lower per-unit cost than flash for high-volume production runs. Typical applications include industrial automation controllers, sensor signal conditioning, consumer electronics interfaces, motor control sub-systems, and mixed-signal embedded products. Its combination of analog and digital peripherals on one die simplifies BOM for cost-sensitive designs. When designing with the PIC14000T-20/SS, ensure the development toolchain matches the OTP variant (PIC14000 OTP parts require a compatible programmer; firmware must be finalized before programming). Decoupling capacitors of 0.1uF should be placed close to VDD/VSS pairs to maintain analog performance. This page synthesizes distributor stock, parametric specifications, drop-in replacement candidates, and practical design notes not consolidated on the manufacturer product page, providing an engineer-ready reference for sourcing and second-sourcing decisions.

RFQ যোগাযোগ
PIC14000T-20I/SO - 8-Bit Mixed Signal MCU 7KB OTP 28-SOIC | Microchip
PIC14000T-20I/SO

PIC14000T-20I/SO - 8-Bit Mixed Signal MCU 7KB OTP 28-SOIC | Microchip

The Microchip Technology PIC14000T-20I/SO is an 8-bit CMOS OTP-based mixed-signal microcontroller in the PIC® 14 family, packaged in a 28-pin SOIC (SO) with industrial temperature grade. It executes instructions in 200 ns at a 20 MHz clock input, integrates 7 KB of OTP program memory organized as 4K x 14 bits, and includes 192 x 8 bytes of RAM for data and stack operations. The device is built around Microchip's PIC RISC architecture and offers only 35 single-word instructions, with all instructions executing in a single cycle except program branches which require two cycles. A PIC (Peripheral Interface Controller) microcontroller is a Harvard-architecture RISC processor optimized for embedded control, widely deployed in automotive, industrial, and consumer applications. The PIC14000 sits within the broader hierarchy of microcontrollers -> embedded processors -> integrated circuits. Its mixed-signal nature positions it specifically within the analog/mixed-signal MCU subcategory, distinguished by integrated peripherals such as comparators, A/D converter channels, and PWM modules. Key features of this variant include a 20 MHz maximum operating frequency, an industrial temperature grade (-40C to +85C) indicated by the 'I' suffix, a tape-and-reel packaging code (T), and surface-mount SO-28 gull-wing leads. The instruction set simplifies code development and reduces learning curve for engineers familiar with PIC microcontrollers, while the OTP memory enables cost-effective production for high-volume applications. Integrated peripherals include multiple analog comparators, capture/compare/PWM modules, and a multi-channel ADC, supporting sensor interface and motor control tasks. The PIC14000 architecture combines a high-performance RISC CPU with mixed-signal peripherals on a single die, eliminating external A/D converters and op-amps in many signal-conditioning applications. This integration reduces BOM count, board area, and system cost. The Harvard architecture separates program and data buses, enabling simultaneous fetch and execution and contributing to the deterministic single-cycle instruction execution that characterizes PIC devices. Typical applications include industrial process control, sensor signal conditioning, smart battery chargers, motor control loops, and analog front-end interfaces. Its mixed-signal capability is particularly suited to applications that combine digital logic with analog sensor inputs and closed-loop feedback. Designers often pair the PIC14000 with precision op-amps, voltage references, and isolated communication transceivers to complete mixed-signal subsystems. When designing with the PIC14000T-20I/SO, consider that OTP memory cannot be reprogrammed in-circuit - code must be burned before final assembly, which influences production flow and firmware revision strategy. Adequate decoupling capacitors (typically 100 nF ceramic plus bulk) near VDD/AVDD and VSS/AVSS pins are essential for ADC accuracy and noise immunity. This page synthesizes distributor pricing, OTP-vs-Flash alternatives within the PIC14 family, and practical design notes that go beyond the manufacturer datasheet to support sourcing and design decisions.

RFQ যোগাযোগ
PIC14000T-20I/SS - 7KB OTP 8-bit Mixed-Signal MCU | Microchip
PIC14000T-20I/SS

PIC14000T-20I/SS - 7KB OTP 8-bit Mixed-Signal MCU | Microchip

The Microchip Technology PIC14000T-20I/SS is a 20 MHz, 8-bit CMOS mixed-signal OTP microcontroller in the PIC® 14 family, packaged in a 28-pin SSOP (0.209 in / 5.30 mm width). It integrates 7 KB of OTP program memory (4K x 14), 192 bytes of SRAM, 20 digital I/O lines, and an on-chip 8-channel 8-bit ADC plus two on-chip comparators — making it one of the few PIC mid-range parts designed for mixed-signal front-end tasks. A PIC microcontroller is a RISC-based 8-bit/16-bit/32-bit MCU built around Microchip's Harvard architecture, used widely in embedded control. The PIC14000 belongs to the mid-range PIC14 sub-family, sitting between the baseline PIC10/12/16 and the enhanced PIC18 cores, and was specifically designed as a mixed-signal controller with built-in analog peripherals for sensor signal chains. Within the power management and embedded hierarchy it sits under: microcontroller -> embedded controller -> mixed-signal MCU -> RISC MCU -> semiconductor IC. Key features of the PIC14000T-20I/SS include a 200 ns single-cycle instruction execution (4 MHz oscillator / 20 MHz ÷ 4 internal), 35 single-word instructions, 8 MHz internal ADC conversion rate, 8-channel 8-bit A/D converter, two analog comparators with programmable reference, internal bandgap voltage reference, on-chip EPROM/OTP program memory, and a wide 2.5 V to 5.5 V operating voltage range. It supports in-circuit serial programming (ICSP) and is offered in industrial temperature grade (-40 °C to +85 °C). The SSOP-28 footprint is pin-compatible with the rest of the PIC14000 family. Architecturally, the PIC14000 uses a 14-bit instruction word with an 8-bit data path, a 2-stage pipeline, and dedicated peripheral modules mapped to the data-memory bus. The 8-bit successive-approximation ADC is paired with two comparators, allowing a designer to perform amplification, thresholding, and digital conversion on-chip — reducing external analog components. The OTP-based program memory supports one-time field programming, with a UV-erasable windowed variant (PIC14000) for development. Typical applications include battery chargers, switched-mode power supply (SMPS) secondary-side control, fan and pump controllers, sensor conditioning front-ends, appliance control, automotive interior lighting, and industrial process loops. The combination of ADC, comparators, and PWM output makes it a single-chip solution for closed-loop analog control. When designing with this part, plan OTP programming early because OTP cannot be re-programmed. Use the windowed PIC14000 (non-T) for prototyping and switch to PIC14000T-20I/SS for production. Decouple VDD with a 0.1 µF ceramic capacitor placed within 5 mm of the pin to keep ADC noise low. This page consolidates distributor pricing, pin-compatible alternatives, and practical design notes that the manufacturer datasheet alone does not provide.

RFQ যোগাযোগ