মাইক্রোকন্ট্রোলার

পণ্য (20,000+)

PIC12LF1571T-I/MS - 8-bit 32MHz MCU, 1.75KB Flash, MSOP-8
PIC12LF1571T-I/MS

PIC12LF1571T-I/MS - 8-bit 32MHz MCU, 1.75KB Flash, MSOP-8

The Microchip Technology PIC12LF1571T-I/MS is an 8-bit RISC PIC12 microcontroller featuring a 32MHz CPU, 1.75KB (1K x 14) of Flash program memory, 128 bytes of SRAM, and 128 bytes of EEPROM data memory, housed in an 8-pin MSOP package. It operates from 1.8V to 3.6V and integrates three 16-bit PWMs with independent timers, a 10-bit ADC, a comparator, and a 5-bit DAC on-chip. An 8-bit microcontroller (MCU) is a small computing system-on-chip that combines a CPU, RAM, non-volatile program memory, and peripherals into a single IC. The PIC12 family sits within Microchip's PIC architecture family of microcontrollers -> 8-bit MCU category -> embedded computing IC -> semiconductor device. 8-bit MCUs are widely deployed in cost- and power-constrained embedded applications because they deliver deterministic instruction execution and very low active/standby current at low BOM cost. Key features of this device include a maximum 32MHz internal oscillator, six general-purpose I/O pins, a 10-bit ADC with up to 4 input channels, one comparator with selectable reference, a 5-bit DAC, three independent 16-bit PWMs, and an Enhanced Universal Synchronous Asynchronous Receiver Transmitter (EUSART). The 'LF' prefix denotes the wide-voltage low-power variant supporting 1.8V to 3.6V operation, ideal for battery-powered designs. Architecturally, the PIC12LF1571 uses Microchip's enhanced mid-range 8-bit core with a single-cycle instruction set, hardware stack, and interrupt controller. The 16-bit PWM modules with independent timers deliver high-resolution pulse-width modulation that competes with 16-bit MCU peripherals at 8-bit cost, enabling precision control loops for LED drivers, fans, and small motor drives without external timer ICs. Typical applications include LED lighting color-mixing and dimming control, battery-powered IoT sensor nodes, small DC fan or motor PWM control, consumer remote controls, and general-purpose logic replacement where simple sequencing and analog measurement are required. The on-chip comparator and 5-bit DAC allow threshold detection and waveform generation without external components. When designing with this device, evaluate whether the 1.75KB Flash and 128 bytes of RAM meet application requirements - small protocol stacks or BLE radio drivers typically cannot fit. Plan for ICSP programming header access (PGD/PGC) and ensure adequate decoupling per the manufacturer application notes for noise-sensitive ADC measurements. This page synthesizes distributor pricing, drop-in alternatives within the PIC12/MSOP-8 footprint, and practical design notes not consolidated in the manufacturer datasheet.

RFQ যোগাযোগ
PIC12LF1571T-I/RF - 8-bit MCU, 1.75KB Flash, 16-bit PWM | Microchip
PIC12LF1571T-I/RF

PIC12LF1571T-I/RF - 8-bit MCU, 1.75KB Flash, 16-bit PWM | Microchip

The Microchip Technology PIC12LF1571T-I/RF is an 8-bit PIC RISC microcontroller with 1.75KB Flash program memory, 128 bytes of RAM, and an integrated 16-bit PWM peripheral, supplied in an 8-pin UDFN exposed-pad package supplied on Tape & Reel. A PIC microcontroller (Peripheral Interface Controller) is a family of 8-bit RISC-based microcontrollers from Microchip Technology built on a Harvard architecture with separate program and data buses. Within the PIC hierarchy this part belongs to PIC12 -> PIC12F -> PIC12LF1571. The LF suffix indicates a wide-voltage (2.5V/3.3V/5V) process node allowing operation down to 1.8V, ideal for battery-powered and energy-harvesting designs. Key features of the PIC12LF1571T-I/RF include three independent 16-bit PWM channels for high-resolution timing, a 32 MHz internal oscillator, 6 I/O pins in an 8-pin UDFN with exposed thermal pad, and on-chip peripherals such as a 10-bit ADC, comparators, EUSART, MSSP (I2C/SPI) and configurable logic cells. The 16-bit PWM with 32 MHz clock delivers sub-microsecond edge resolution suited to LED dimming and motor control. The PIC12LF1571 architecture uses a 14-bit instruction word with a 32-byte register file and a single-cycle ALU, enabling predictable deterministic timing critical for real-time control. The LF variant uses the same core as the PIC12F1571 but with a wider voltage range and lower-power Brown-out Reset and Watchdog Timer configuration, making it suitable for low-voltage battery systems. Typical applications include high-resolution LED lighting control, stepper motor and DC motor drive PWM generation, switched-mode power supply control loops, fan speed controllers, and small sensor-conditioning platforms. Designers choose this part where board area is constrained and 16-bit PWM resolution removes the need for an external timer IC. When designing with this part, ensure that the ICSP programming pins (ICSPCLK/ICSPDAT) are accessible on the PCB for in-circuit programming and debugging, and that the exposed thermal pad on the UDFN package is soldered for both thermal dissipation and mechanical reliability. The wide 1.8V-3.6V supply range simplifies integration into 2x AA, coin-cell, or Li-Ion battery systems. This page synthesizes distributor pricing, same-family drop-in alternatives, and practical PCB design notes that complement the manufacturer datasheet for engineers selecting the PIC12LF1571T-I/RF.

RFQ যোগাযোগ
PIC12LF1572-E/RF - 8-bit MCU, 32MHz, 3.5KB Flash, 16-bit PWM | Microchip
PIC12LF1572-E/RF

PIC12LF1572-E/RF - 8-bit MCU, 32MHz, 3.5KB Flash, 16-bit PWM | Microchip

The Microchip Technology PIC12LF1572-E/RF is an 8-bit PIC12 microcontroller delivering 32MHz CPU performance with 3.5KB (2K x 14) Flash program memory and 256 bytes RAM in an 8-pin UDFN (3x3mm) package. The device integrates three independent 16-bit PWMs with dedicated timers, a 10-bit ADC, configurable logic cells (CLC), and a complementary waveform generator (CWG) targeting LED lighting, stepper motor, and power-conversion applications. A microcontroller (MCU) is a single-chip computer containing a CPU, program memory (Flash), data memory (RAM), and programmable peripherals. The PIC12LF1572 belongs to the PIC® 12F family of 8-pin mid-range microcontrollers; this LF variant operates from 1.8V to 3.6V and is optimized for low-voltage, low-power designs. Within the broader taxonomy, an MCU is a subset of microcomputer -> embedded processor -> integrated circuit. The PIC12LF1572 family pairs a RISC Harvard-architecture core with Core Independent Peripherals (CIPs) so timers, PWM, and logic blocks run without CPU intervention, enabling deterministic real-time control with minimal code overhead. Key features include three 16-bit PWMs (1.0ns PWM resolution at 32MHz) for high-resolution dimming and motor control, four 10-bit ADC channels with hardware averaging, two comparators, two CLCs, and one CWG with auto-shutdown. The device supports in-circuit serial programming (ICSP), provides 25mA source/sink per I/O, and includes a low-power sleep mode with <50nA typical current. Two speed grades and an extended (-40C to +125C) temperature option make it suitable for industrial and consumer-grade applications. The PIC12LF1572 uses an enhanced mid-range 8-bit core with a 14-bit instruction word, 8-level hardware stack, and interrupt controller with hardware context save. CIPs (PWM, CLC, CWG) execute autonomously, freeing the CPU for system-level tasks and reducing firmware complexity. The 1.8V minimum VDD allows direct Li-ion or 2xAA battery operation without external regulators. Typical applications include LED lighting color-mixing and dimming, brushed DC motor and stepper control, switched-mode power supply (SMPS) feedback loops, and consumer remote controls. The three 16-bit PWMs are particularly well suited to high-resolution RGB or white-LED dimming where 8 or 10-bit PWM granularity is insufficient. When designing with the PIC12LF1572-E/RF, ensure VDD decoupling includes a 100nF ceramic capacitor placed within 5mm of the VDD pin, and use a 10kohm pull-up on MCLR for reliable ICSP programming. The UDFN 3x3mm package has an exposed thermal pad that should be soldered to the ground plane for mechanical reliability. This page consolidates distributor pricing, drop-in PIC12F1571/1572 family alternatives, and practical design notes not aggregated in the manufacturer datasheet alone.

RFQ যোগাযোগ
PIC12LF1572-E/SN - 8-bit MCU, 32MHz, 3.5KB Flash, 16-bit PWM | Microchip
PIC12LF1572-E/SN

PIC12LF1572-E/SN - 8-bit MCU, 32MHz, 3.5KB Flash, 16-bit PWM | Microchip

The Microchip Technology PIC12LF1572-E/SN is an 8-bit RISC microcontroller from the PIC12 family, featuring a PIC12 CPU core operating at up to 32MHz, 3.5KB (2K x 14) of Flash program memory, 256 bytes of RAM, and 128 bytes of Data EEPROM, housed in an 8-pin SOIC (SN) package. It operates from a wide 1.8V to 3.6V supply and integrates three independent 16-bit PWM channels, six timers, a comparator, an EUSART, a brown-out reset (BOR), a power-on reset (POR), and a watchdog timer (WDT). An 8-bit microcontroller (MCU) is a compact computing-on-a-chip built around an 8-bit data path, integrating CPU, RAM, non-volatile program memory, and peripheral I/O on a single silicon die. Within the broader semiconductor taxonomy, the PIC12LF1572 sits under MCU -> microcontroller -> embedded controller -> semiconductor, optimized for low-pin-count, low-power, mixed-signal embedded designs where deterministic real-time response, low sleep current, and small footprint are critical. Key features of this device include three 16-bit PWMs with independent timers that deliver high-resolution control ideal for LED lighting, stepper motors, and switched-mode power supplies. The integrated high-performance comparator supports mixed-signal feedback loops, while the EUSART provides robust asynchronous and synchronous serial communication. The LF process node (low-voltage, low-power) enables deep sleep currents in the nanoampere range, extending battery life in energy-harvesting applications. The architecture uses a Harvard-class RISC core with a 14-bit instruction word and a 200 ns instruction execution time at 20 MHz (one instruction per 4 clock cycles in this device), and offers Core Independent Peripherals (CIPs) that operate without CPU intervention. Three 16-bit PWM outputs, a 5-bit DAC, and the 16-bit timer/counter can be interconnected via the peripheral pin select and PPS-less fabric to form closed-loop analog or feedback control paths. Typical applications include LED lighting and color-mixing control, stepper motor and DC motor drive for low-power robotics, switch-mode power supply feedback, battery management and metering, IoT end-node sensor conditioning, and general-purpose industrial automation. The wide operating voltage range and ultra-low power modes also make the part attractive for handheld instruments and remote sensor nodes. When designing with this device, place a 0.1 uF decoupling capacitor as close as possible to VDD and use a 10 uF bulk capacitor on the supply rail. Confirm that the chosen programming tool (e.g., PICkit 4 or MPLAB SNAP) supports the PIC12LF1572 device ID before board bring-up. Do not exceed the absolute maximum VDD of 4.0V; the LF variant is not 5V tolerant. This page synthesizes distributor pricing, pin-compatible drop-in alternatives, application notes, and practical design notes not found in the manufacturer datasheet, giving embedded engineers a faster path from part selection to prototype.

RFQ যোগাযোগ
PIC12LF1572-I/MF - 8-Bit 32MHz MCU 3.5KB Flash | Microchip
PIC12LF1572-I/MF

PIC12LF1572-I/MF - 8-Bit 32MHz MCU 3.5KB Flash | Microchip

The Microchip Technology PIC12LF1572-I/MF is an 8-bit RISC PIC microcontroller featuring a PIC12 CPU core, operating at up to 32MHz and integrating 3.5KB (2K x 14) of Flash program memory with 256 bytes of RAM in an 8-pin DFN (3x3) package. As the 'LF' variant, it supports an extended low-voltage operating range of 1.8V to 3.6V, making it suited to battery-powered and energy-harvesting applications. An 8-bit microcontroller (MCU) is a single-chip computer built around an 8-bit data path, Flash program memory, RAM, and on-chip peripherals such as timers, ADCs, and PWMs. PIC microcontrollers from Microchip use a Harvard RISC architecture, where program and data buses are separate, enabling single-cycle instruction execution and deterministic timing. The PIC12LF1572 belongs to the PIC12 sub-family of low-pin-count 8-bit MCUs and sits within Microchip's broader product hierarchy: 8-bit MCU -> PIC microcontroller -> PIC12 family -> PIC12F sub-family -> power-management/lighting-oriented PIC12LF157x series. Its place in this taxonomy makes it a common building block in compact, low-cost embedded designs. Key features of the PIC12LF1572 include three independent 16-bit PWMs with dedicated timers, high-resolution analog peripherals, a 10-bit ADC, comparators, EUSART (Enhanced Universal Synchronous Asynchronous Receiver Transmitter) for serial communication, and Core Independent Peripherals (CIPs) that offload tasks from the CPU. The 16-bit PWM channels are the headline feature, providing fine-grained duty cycle control needed for LED dimming, motor control, and switch-mode power supply regulation. The device also supports high-voltage In-Circuit Serial Programming (ICSP) for flexible programming in production. Typical applications include LED lighting drivers (RGB and white), stepper motor control, DC-DC converter control loops, battery chargers, and small general-purpose embedded control boards. The 1.8V minimum supply allows direct connection to single-cell Li-Ion or two-cell alkaline battery stacks. Combined with its tiny 3x3 mm DFN footprint, the part enables very compact PCB designs in cost-sensitive consumer and industrial products. When designing with this part, place a 0.1uF decoupling capacitor close to the VDD pin and respect the 1.8V-3.6V supply range. For low-power sleep modes, configure the CPU and peripherals carefully via the SLP and IDLE bits to minimize quiescent current. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ যোগাযোগ
PIC12LF1572-I/MS - 8-bit 32MHz 3.5KB Flash MCU | Microchip
PIC12LF1572-I/MS

PIC12LF1572-I/MS - 8-bit 32MHz 3.5KB Flash MCU | Microchip

The Microchip Technology PIC12LF1572-I/MS is an 8-bit PIC microcontroller from the PIC12(L)F1571/2 family, combining three independent 16-bit PWMs with 10-bit ADC and analog peripherals in an 8-pin MSOP package. It runs at up to 32MHz, integrates 3.5KB Flash program memory (2K x 14 words), 256 bytes of RAM, and operates across a wide 1.8V to 3.6V supply range suitable for battery-powered designs. A microcontroller (MCU) is a single-chip computer containing a CPU, non-volatile program memory (Flash), volatile data memory (RAM), and programmable I/O. Within the broader device hierarchy, an MCU is a type of embedded processor (microprocessor with integrated peripherals) classified under microcontrollers, then 8-bit microcontrollers, then the PIC family. The 8-bit PIC RISC architecture executes most instructions in one clock cycle, enabling deterministic timing that is valuable for real-time control loops such as PWM generation, motor commutation, and sensor sampling. Key features include three independent 16-bit PWMs with their own timers (suitable for high-resolution LED dimming and stepper motor control), a 10-bit ADC with computation (ADC2), a comparator, EUSART (Enhanced USART) for serial communication, and an internal 31kHz to 32MHz oscillator. The LF (low-power) silicon variant extends the supply range down to 1.8V, making it a strong fit for 2x AA / coin-cell applications. The device also supports the PICkit and ICD programming/debug toolchain for in-circuit development. Architecturally, the PIC12LF1572-I/MS uses a Harvard RISC core with separate program and data buses. The three 16-bit PWM modules can operate independently of CPU execution - once configured, they generate outputs without software intervention, freeing the core for measurement and communication. The 32MHz internal oscillator provides factory-calibrated accuracy and removes the need for external crystals in cost-sensitive designs. Typical applications include LED lighting controllers, battery-powered sensor nodes, handheld consumer products, fan and pump speed controllers, and general-purpose low-cost embedded control where compact 8-pin footprint and integrated 16-bit PWM resolution are required. The combination of three PWMs and 10-bit ADC makes it especially suited to closed-loop lighting and motor control. When designing with this part, ensure the supply rail is decoupled with 100nF + 10uF ceramic capacitance placed close to the VDD pin. For accurate ADC readings, configure the ADC2 averaging and add a low-pass RC filter at the analog input. The ICSP programming pins (ICSPCLK/ICSPDAT) share pads with GPIO and may require isolation resistors in production layouts. This page synthesizes distributor pricing, drop-in same-package alternatives (PIC12F1572-I/MS, PIC12LF1571-I/MS), and practical design notes not consolidated on a single manufacturer or distributor page.

RFQ যোগাযোগ
PIC12LF1572-I/P - 8-bit MCU, 32MHz, 3.5KB Flash, 8-PDIP | Microchip
PIC12LF1572-I/P

PIC12LF1572-I/P - 8-bit MCU, 32MHz, 3.5KB Flash, 8-PDIP | Microchip

The Microchip PIC12LF1572-I/P is an 8-bit RISC microcontroller based on the enhanced mid-range PIC® core, operating up to 32MHz with 3.5KB (2K x 14) of Flash program memory and 256 bytes of SRAM, housed in an 8-pin PDIP through-hole package. It features three independent 16-bit PWM modules with complementary waveform outputs, a 10-bit ADC with 4 channels, a 5-bit DAC with 1 channel, and a high-performance comparator, all designed for mixed-signal applications in a compact 8-pin footprint. A microcontroller (MCU) is an integrated circuit containing a processor core, memory, and programmable input/output peripherals on a single silicon die. The PIC12LF1572 belongs to the PIC12 (L)F157x family from Microchip, which targets cost-sensitive embedded designs that need precision analog and PWM generation. The 'LF' suffix indicates a wide operating voltage range of 1.8V to 3.6V, making this part ideal for battery-powered and low-voltage systems where energy efficiency is critical. Key features include three 16-bit PWMs with independent timers delivering high-resolution pulse-width modulation suitable for LED lighting, stepper motor control, and switched-mode power supplies. The device integrates a 10-bit ADC, a 5-bit DAC, two comparators, an Enhanced Universal Synchronous Asynchronous Receiver Transmitter (EUSART), and 5-bit digital signal conditioning blocks (DSM). Its 32MHz internal oscillator eliminates external crystal requirements, reducing BOM cost and PCB area. The architecture uses a 14-bit instruction word with single-cycle execution except for program branches, providing deterministic timing. With 35 instructions and hardware stack depth of 16, this MCU simplifies code development in MPLAB® X IDE using XC8 compilers. The peripheral pin select (PPS) is not available on this 8-pin device, so pin assignments are fixed per the device datasheet. Typical applications include LED lighting drivers, brushless DC fan control, small stepper motor control, battery chargers, and general-purpose mixed-signal embedded control. The wide 1.8V-3.6V operating range and integrated analog peripherals reduce the external component count significantly. When designing with this MCU, ensure the supply voltage stays within the 1.8V to 3.6V LF range; the non-LF PIC12F1572 variant supports 2.3V to 5.5V. Decouple VDD with a 0.1uF ceramic capacitor placed within 5mm of the IC pins. The ICSP™ programming pins (ICSPCLK/ICSPDAT) are shared with GPIO, so design the PCB to allow in-circuit programming access during development.

RFQ যোগাযোগ
PIC12LF1572-I/RF - 8-Bit MCU, 3.5KB Flash, 3x16-bit PWM | Microchip
PIC12LF1572-I/RF

PIC12LF1572-I/RF - 8-Bit MCU, 3.5KB Flash, 3x16-bit PWM | Microchip

The Microchip Technology PIC12LF1572-I/RF is an 8-bit PIC microcontroller built around the enhanced mid-range core running at up to 32 MHz, delivering 3.5 KB (2K x 14) of self-programmable Flash program memory, 256 bytes of RAM, and housed in a compact 8-pin UDFN (3x3 mm) exposed-pad package. The device integrates three independent 16-bit PWMs with dedicated timers, a 10-bit ADC with 4 channels, a 5-bit DAC, two comparators, and an EUSART, making it one of the most feature-dense 8-pin microcontrollers in the PIC12 family. It operates from a wide 1.8V to 3.6V supply range, supporting low-voltage battery-powered designs including single-cell Li-ion and 2x AA alkaline topologies. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory, working RAM, and configurable peripherals. The PIC12 family is Microchip's baseline 8-pin PIC line, optimized for cost-sensitive applications where board space is at a premium. Within that hierarchy, the PIC12LF1572 belongs to the enhanced mid-range core generation with a C-compiler-optimized RISC architecture. Its place in the broader taxonomy is: 8-bit microcontroller -> embedded controller -> semiconductor IC. Compared to legacy PIC12F parts, the 1572 adds high-resolution 16-bit PWM channels specifically tuned for LED lighting, power conversion, and motor control. Key differentiating features include three independent 16-bit PWMs (vs. the typical 10-bit PWM found on older PIC12F parts), a 10-bit ADC up to 100 ksamples/s, an on-chip 5-bit DAC usable as a programmable voltage reference, two high-speed comparators, and an internally calibrated 32 MHz HFINTOSC. The device supports in-circuit serial programming (ICSP) via the standard Microchip ICD toolchain, and includes a watchdog timer, brown-out reset, and on-chip voltage reference for robust field operation. The architecture pairs an 8-bit data path with a 14-bit instruction word, allowing most instructions to execute in a single cycle. With 49 instructions and 16-level hardware stack, code density is high and interrupt latency deterministic - important for real-time PWM control loops. The integrated 16-bit PWM resolution means stepping granularity of about 488 Hz at a 32 MHz Fosc, a 256x improvement over 8-bit PWM, which is critical for digital LED dimming, where perceived flicker and color shift depend on PWM depth. Typical applications include LED lighting and RGB color mixing, stepper motor and DC motor control, switched-mode power supply feedback, capacitive-touch user interfaces, fan speed controllers, and general-purpose sensor hubs. The combination of three PWMs plus a 10-bit ADC plus a DAC makes the PIC12LF1572-I/RF a self-contained analog/digital front-end in a single 8-pin package. When designing with this part, verify that the UDFN exposed-pad is properly soldered and thermally connected to the ground plane; the EP serves as the primary thermal and electrical return path. Plan GPIO usage carefully - the 8-pin package exposes only 6 general-purpose I/O pins, of which several are multiplexed with the comparators, ADC, and PWM outputs. This page synthesizes distributor pricing from 9 sources, parametric comparison with same-footprint variants, and practical design notes not found in the manufacturer datasheet - covering drop-in alternatives in the UDFN-8 footprint and common thermal/layout pitfalls.

RFQ যোগাযোগ
PIC12LF1572T-I/MF - 8-Bit MCU, 32MHz, 3.5KB Flash, 8-DFN | Microchip
PIC12LF1572T-I/MF

PIC12LF1572T-I/MF - 8-Bit MCU, 32MHz, 3.5KB Flash, 8-DFN | Microchip

The Microchip Technology PIC12LF1572T-I/MF is a low-power 8-bit PIC microcontroller from the PIC12(L)F157X family, operating at up to 32 MHz with 3.5 KB (2K x 14) of Flash program memory, 256 bytes of RAM, and housed in an 8-pin DFN (3x3 mm) package. The device integrates three independent 16-bit PWMs with dedicated timers, a 10-bit ADC, a comparator, and a configurable EUSART peripheral, making it purpose-built for high-resolution PWM applications such as LED lighting, stepper motor drive, and digital power conversion. An 8-bit microcontroller (MCU) is a small computer-on-a-chip built around an 8-bit data path; it executes one byte per instruction and is widely used in cost-sensitive embedded designs where deterministic timing and ultra-low standby power are more important than raw compute throughput. The PIC12F157X family adds 16-bit PWM channels to the traditional 8-bit core, which is unusual: most 8-bit MCUs offer only 8 or 10-bit PWM. This bridges the gap between low-cost 8-bit controllers and higher-end 16-bit Digital Signal Controllers for applications that demand fine-grained duty-cycle control without paying for a 16-bit core. Key features include three independent 16-bit PWMs (1.6 ns resolution at 32 MHz), an integrated 10-bit ADC with up to 6 channels, an analog comparator with a 4-bit DAC reference, an EUSART module for asynchronous serial communications, and four hardware-driven Core Independent Peripherals (CIPs) that operate without CPU intervention. The "LF" suffix denotes the wide-Vdd 1.8V-3.6V operating range, optimized for battery-powered and energy-harvesting designs. Brown-out Reset (BOR), Power-On Reset (POR), and a low-power Sleep mode (typically under 50 nA) support extended battery life in always-on products. Typical applications include LED lighting dimming and color-mixing controllers, brushed DC and stepper motor drivers, switched-mode power supply (SMPS) digital control loops, remote controls, sensor signal conditioning, and small-form-factor IoT edge nodes. The DFN-8 package makes the part attractive where board area is at a premium, such as in smart wearables or miniaturized sensor modules. When designing with this part, ensure the configured system clock does not exceed 32 MHz and that the EUSART baud-rate generator error is checked at the target temperature. Because the 16-bit PWM time-base can drive the part beyond what 8-bit timers typically achieve, plan filter component values and dead-time insertion carefully to avoid shoot-through in half-bridge drive applications. This page synthesizes distributor pricing, drop-in 8-pin alternatives, and practical design notes not found in the standalone datasheet PDF.

RFQ যোগাযোগ
PIC12LF1572T-I/MS - 8-bit 32MHz MCU 3.5KB Flash 8-MSOP | Microchip
PIC12LF1572T-I/MS

PIC12LF1572T-I/MS - 8-bit 32MHz MCU 3.5KB Flash 8-MSOP | Microchip

The Microchip Technology PIC12LF1572T-I/MS is an 8-bit PIC12F-series microcontroller built around a 32MHz RISC core, delivering 3.5KB (2K x 14 words) of Flash program memory and 256 bytes of SRAM in an 8-pin MSOP package. It operates from 1.8V to 3.6V with an integrated 16-bit PWM, a 5-bit DAC, and a 4-channel 10-bit ADC for compact mixed-signal designs. An 8-bit microcontroller (MCU) is a single-chip computer that integrates an 8-bit CPU core, program memory, RAM, and peripherals onto a single silicon die. In the broader taxonomy, an MCU belongs to the microcontroller family, which falls under microcontrollers, integrated circuits, and finally semiconductors. The PIC12F line targets low-pin-count, cost-sensitive applications where the smallest package and lowest power matter most, and the PIC12LF1572 belongs to the PIC12(L)F157X sub-family that combines 16-bit PWMs with analog peripherals. The "LF" prefix denotes the wide-voltage, low-power variant optimized for battery-powered and energy-harvesting products. Key features include three independent 16-bit PWMs with dedicated timers, a hardware 5-bit DAC that complements the 10-bit ADC, an Enhanced Universal Synchronous Asynchronous Receiver Transmitter (EUSART), and up to 6 general-purpose I/O pins. Internal oscillator options eliminate external crystals in many designs, while the in-circuit serial programming (ICSP) interface allows field upgrades. Compared with traditional 8-bit MCUs that only offer 8 or 10-bit PWMs, the 16-bit PWM resolution enables finer control of LED brightness and motor position. Technically, the PIC12LF1572 uses a Harvard RISC architecture with a 14-bit instruction word and single-cycle execution, allowing deterministic interrupt response for real-time control. The 32MHz internal oscillator provides 8 MIPS throughput, with low-power Sleep and Idle modes reducing quiescent current to support battery-operated systems. Typical applications include RGB LED lighting strips, small DC motor or fan speed controllers, low-cost SMPS primary-side control, and consumer remote controls. The combination of wide-voltage operation, high-resolution PWM, and integrated DAC makes it especially well suited to general-purpose lighting and power-conversion tasks. When designing, place the device close to its supply decoupling capacitor and route the analog AVdd/DAC traces away from PWM outputs. Verify that total GPIO sourcing does not exceed the package's 50 mA per-pin limit. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, giving engineers and buyers a faster path to a qualified design.

RFQ যোগাযোগ
PIC12LF1572T-I/RF - 8-bit 32MHz 3.5KB Flash MCU | Microchip
PIC12LF1572T-I/RF

PIC12LF1572T-I/RF - 8-bit 32MHz 3.5KB Flash MCU | Microchip

The Microchip PIC12LF1572T-I/RF is an 8-bit CMOS flash microcontroller from the PIC® 12F family, featuring a 32MHz internal oscillator, 3.5KB (2K x 14) of flash program memory, and 256 bytes of RAM, all integrated into a compact 8-pin UDFN (3x3 mm) exposed-pad package with tape-and-reel packaging. It delivers three independent 16-bit PWMs with dedicated timers, an on-chip 5-bit DAC, a comparator, a 10-bit ADC, and an EUSART, making it a versatile solution for mixed-signal applications where high-resolution PWM and analog integration are required in a minimal footprint. A PIC microcontroller (MCU) is a compact programmable processor built on Harvard architecture with separate program and data buses, typically used for embedded control tasks such as sensor reading, motor driving, LED dimming, and signal generation. Within the broader category, the PIC12F family represents the smallest pin-count 8-bit PICs, the PIC12LF sub-family denotes low-voltage (1.8V-3.6V) operation, and PIC microcontrollers in general sit within the wider taxonomy of microcontrollers > processors > semiconductors > integrated circuits. Key features of the PIC12LF1572T-I/RF include three 16-bit PWMs with independent timers suitable for high-resolution LED lighting and motor control, a 5-bit DAC, a comparator, and a 10-bit ADC with up to 6 channels. It supports a wide operating voltage of 1.8V to 3.6V, low-power sleep modes, an integrated 32MHz internal oscillator, and an EUSART module for asynchronous serial communication. The 8-UDFN exposed-pad package provides a compact 3x3 mm footprint with excellent thermal dissipation for high-density PCB layouts. Architecturally, this device uses Microchip's enhanced mid-range 8-bit core with a 14-bit instruction word and a 200 ns instruction execution time at 32MHz. The combination of three independent 16-bit PWM channels, a 5-bit DAC, and a 10-bit ADC in such a small package makes it a unique solution for cost-sensitive designs that need both analog and PWM peripherals in minimal board space. Typical applications include LED lighting control, RGB color mixing, DC-DC converter control, battery management, and small motor control in consumer electronics, IoT nodes, and portable devices. The wide 1.8V-3.6V supply range makes it ideal for direct battery-powered designs. When designing with this MCU, ensure that the UDFN exposed pad is soldered to a sufficient copper area for thermal performance, and review the configuration bits carefully to enable the peripherals you need. The internal 32MHz oscillator eliminates the need for an external crystal, reducing BOM cost. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, providing actionable information for engineers evaluating the PIC12LF1572T-I/RF for embedded designs.

RFQ যোগাযোগ
PIC12LF1572T-I/SN - 8-Bit MCU, 3.5KB Flash, 32MHz, 8-SOIC | Microchip
PIC12LF1572T-I/SN

PIC12LF1572T-I/SN - 8-Bit MCU, 3.5KB Flash, 32MHz, 8-SOIC | Microchip

The Microchip Technology PIC12LF1572T-I/SN is an 8-bit RISC microcontroller featuring 3.5KB (2K x 14) of Flash program memory, 256 bytes of SRAM, and a maximum CPU clock speed of 32MHz, all integrated into an 8-pin SOIC package. It operates from a 1.8V to 3.6V supply rail, consumes low active and sleep currents, and integrates three 16-bit PWMs with independent timers, a comparator, a 10-bit ADC with 4 channels, and a 5-bit DAC for high-resolution analog signal generation. A microcontroller (MCU) is a single-chip computer that contains a processor core, volatile and non-volatile memory, and configurable peripheral blocks. The PIC12LF1572 belongs to Microchip's enhanced mid-range PIC12 family, which targets cost-sensitive, low-pin-count embedded applications. In the broader taxonomy, it sits under 8-bit microcontroller -> microcontroller -> embedded processor -> semiconductor, occupying the smallest-footprint tier alongside PIC10, PIC12, and PIC16 families. Key differentiating features of the PIC12LF1572 include three independent 16-bit PWMs (vs. the 10-bit PWM blocks found on older PIC12F parts), a 10-bit ADC with selectable conversion modes, a 5-bit DAC, an Enhanced Universal Synchronous Asynchronous Receiver Transceiver (EUSART), and an inter-module crossbar supporting flexible signal routing between peripherals. The 32MHz internal oscillator eliminates the need for an external crystal in many designs, reducing BOM cost and board area. Architecturally, the PIC12LF1572 uses a Harvard RISC core with a 14-bit instruction word, allowing most instructions to execute in a single instruction cycle (125 ns at 32 MHz FOSC). The on-chip debug logic (ICD) and the in-circuit serial programming (ICSP) interface support Microchip's MPLAB X IDE and PICkit programmers, accelerating firmware bring-up. Typical applications include LED lighting and color-mixing controllers, household appliance user interfaces, battery-powered sensor nodes, simple motor and fan control loops, and general-purpose logic replacement where designers need more flexibility than a discrete 555 timer but fewer resources than a 32-bit MCU. The 16-bit PWM resolution makes the part especially well suited to high-resolution dimming and motor torque control. Designers should pay particular attention to the 1.8V to 3.6V supply range. When migrating from the 5V-tolerant PIC12F1572, note that the 'LF' variant is the low-voltage part - do not power it from a 5V rail or the device will be damaged. Decoupling should follow Microchip's recommended 0.1uF + 10uF capacitor arrangement. This page consolidates distributor pricing, drop-in SOIC-8 alternatives, and practical design notes that go beyond the manufacturer datasheet to help procurement and embedded engineers make a fast, well-informed decision.

RFQ যোগাযোগ
PIC12LF1612-E/MF - 8-Bit MCU, 32MHz, 3.5KB Flash | Microchip
PIC12LF1612-E/MF

PIC12LF1612-E/MF - 8-Bit MCU, 32MHz, 3.5KB Flash | Microchip

The Microchip PIC12LF1612-E/MF is a 8-bit PIC microcontroller operating at up to 32 MHz with 3.5 KB (2K x 14) of Flash program memory and 256 bytes of RAM, housed in an 8-pin VDFN (3x3 mm) exposed-pad package. The 'LF' prefix denotes the wide-voltage 1.8V-3.6V variant, ideal for battery-powered designs, while the 'E' suffix indicates the -40C to +125C extended operating temperature range suited to industrial environments. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), data memory (RAM), and peripheral set (timers, ADC, communications, comparators, PWM). Within the broader taxonomy, the PIC12LF1612 is an 8-bit RISC MCU -> microcontrollers -> microcomputer -> embedded computing -> semiconductors. Microchip's PIC10/12/16 families target ultra-low-pin-count (6-20 pin) applications where small footprint and low power are critical design constraints. Key features include one 10-bit ADC with computation, two 8-bit timers and one 16-bit timer, enhanced PWM with independent timing, complementary waveform generator, Configurable Logic Cell (CLC), Zero-Cross Detection, 24-bit Signal Measurement Timer (SMT), I2C/SPI/UART (EUSART) interfaces, and on-board 31 kHz internal oscillator. These peripherals make the PIC12LF1612 a flexible building block for sensor conditioning, LED driving, and small-motor control. The architecture uses Microchip's enhanced mid-range core with a 14-bit instruction word, 8-level hardware stack, and 32 MHz internal oscillator. The CIP (Core Independent Peripherals) such as CLC and NCO offload tasks from the CPU, freeing it for application logic. Internal voltage reference, DAC, and comparators allow precision analog signal chain implementations without external components. Typical applications include battery-powered IoT sensor nodes, LED lighting controllers, small DC motor drivers (fans, pumps, valves), consumer remote controls, and general-purpose 8-bit control replacements for older PIC10F/12F designs. The 1.8V minimum supply extends runtime on Li-coin or 2x AA cells. Designers should use MPLAB X IDE with XC8 compiler and MPLAB Code Configurator (MCC) for rapid peripheral setup. The 'MF' suffix (VDFN-8, 3x3 mm) requires careful PCB layout with thermal/exposed-pad connection to GND. This page synthesizes real distributor pricing, drop-in 8-pin VDFN alternatives, and field engineering design notes not aggregated elsewhere - optimized to help you select, source, and integrate the PIC12LF1612-E/MF in production.

RFQ যোগাযোগ
PIC12LF1612-E/P - 8-Bit 32MHz MCU 3.5KB Flash | Microchip
PIC12LF1612-E/P

PIC12LF1612-E/P - 8-Bit 32MHz MCU 3.5KB Flash | Microchip

The Microchip Technology PIC12LF1612-E/P is an 8-bit RISC PIC microcontroller built on a CMOS process, delivering 32MHz CPU performance from a 3.5KB (2K x 14) flash program memory in a through-hole 8-pin PDIP package. The 'LF' suffix indicates the low-power (F) process node that supports a wide 1.8V to 3.6V supply range, while the 'E' temperature grade marks the -40C to +125C extended-industrial operating window. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, non-volatile program memory, working RAM, and a rich set of peripheral IP blocks such as ADC, DAC, PWM, timers, and communication controllers. Within the broader semiconductor taxonomy, an MCU sits below microprocessors (MPUs) in capability but above pure logic ICs in functional density, making it the workhorse of embedded control. The PIC12LF1612 belongs to the PIC12 mid-range 8-bit family from Microchip, optimized for cost-sensitive, low-power, and battery-friendly designs. Key differentiating features include the on-chip 10-bit A/D converter with internal Fixed Voltage Reference, a 5-bit DAC, four 10-bit PWM channels, a hardware Zero-Cross Detector, the Configurable Logic Cell (CLC), and the Numerically Controlled Oscillator (NCO) that delivers 20-bit resolution peripheral clocking. The device also integrates an 8-bit timer with 2:1 prescaler, a 16-bit timer, and the Zero-Cross Detect module - features typically found in larger pin-count MCUs. The 8-pin PDIP form factor keeps the bill-of-materials low while exposing five general-purpose I/O pins. Technically, the PIC12LF1612 uses the enhanced mid-range 14-bit instruction-set architecture with a 2-stage pipeline and 8-deep hardware stack, providing predictable interrupt latency and deterministic execution. The internal 31kHz LFINTOSC and 16MHz HFINTOSC eliminate the need for an external crystal in most designs, while the 32kHz Timer1 oscillator domain supports real-time-clock-style timing on a coin-cell battery. Typical applications include small DC-motor and fan control via the PWM + CLC blocks, white-goods and appliance user-interface replacement, low-cost sensor-conditioning nodes, signal-conditioning for zero-cross triac dimmers, and portable consumer products where the wide 1.8V-3.6V supply tolerates single-cell lithium or two-cell alkaline chemistries. The automotive temperature grade makes the part suitable for cabin and under-hood-adjacent modules. When designing with this part, prefer the internal HFINTOSC to minimize board area and BOM cost; only add an external crystal when system timing must track a precision reference. Decouple VDD with a 0.1uF ceramic capacitor placed within 5mm of the supply pin, and ensure unused I/O pins are configured as outputs-low to minimize current leakage. This page synthesizes verified distributor pricing, a same-brand drop-in alternative matrix, and design notes not bundled in the manufacturer datasheet, complementing Microchip's product family page for the PIC12F1612 / PIC16(L)F161x family.

RFQ যোগাযোগ
PIC12LF1612-E/SN - 8-bit MCU, 3.5KB Flash, 32MHz, 8-SOIC | Microchip
PIC12LF1612-E/SN

PIC12LF1612-E/SN - 8-bit MCU, 3.5KB Flash, 32MHz, 8-SOIC | Microchip

The Microchip Technology PIC12LF1612-E/SN is an 8-bit RISC microcontroller built on the PIC12 CPU core, delivering up to 32MHz of computational performance from 3.5KB of Flash program memory and 256 bytes of RAM, housed in an 8-lead SOIC (SN) package. The "LF" suffix denotes the extended low-voltage variant (1.8V to 3.6V VDD), while the "F" in the family name designates Flash-based program memory. The device integrates peripherals including ADC, DAC, PWM and an internal oscillator optimized for low-power embedded designs. An 8-bit PIC microcontroller is a compact, deterministic RISC processor that combines the CPU core, non-volatile Flash program memory, data SRAM, and configurable peripherals into a single CMOS IC. In the broader system hierarchy, the PIC12 family sits at the small-footprint end of Microchip's 8-bit portfolio (PIC10/PIC12/PIC16/PIC18), making it ideal for cost-sensitive, space-constrained applications where deterministic interrupt response and low quiescent current matter more than raw MIPS. Key specifications include 3.5KB (2K x 14) Flash program memory, 256 bytes SRAM, 32MHz internal oscillator with 4x PLL option, integrated 8-bit ADC and 5-bit DAC, multiple PWM channels, and an industrial-grade -40C to +125C operating temperature range. The low-voltage core lets the part run from a single Li-ion cell or two AA batteries, while internal oscillator accuracy eliminates the need for an external crystal in most designs. Architecturally the PIC12LF1612 uses a Harvard RISC core with a 14-bit instruction word, hardware multiplier-free ALU, and peripheral pin select that allows flexible routing of digital functions to physical I/O. Power-managed sleep modes drop quiescent current into the microamp range, supporting always-on sensor and remote-control applications. The device is supported by Microchip's MPLAB X IDE and XC8 compiler toolchain, as well as the MPLAB Code Configurator for peripheral setup. Typical applications include battery-powered IoT sensor nodes, RGB LED color-mixing controllers using the on-chip PWM and DAC, low-cost smoke/CO detector signal chains, consumer remote controls, small home appliances, and aftermarket automotive accessories operating off a single cell. When designing with this part, confirm that the 1.8V minimum VDD covers brown-out and battery-end-of-life conditions for your energy source; add a 0.1uF decoupling capacitor within 5mm of VDD, and route the ICSPDAT/ICSPCLK lines with a test-point-friendly stub if in-field firmware updates are required. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the standalone manufacturer datasheet.

RFQ যোগাযোগ
PIC12LF1612-I/P - 8-bit MCU 3.5KB Flash 256 RAM 32MHz | Microchip
PIC12LF1612-I/P

PIC12LF1612-I/P - 8-bit MCU 3.5KB Flash 256 RAM 32MHz | Microchip

The Microchip Technology PIC12LF1612-I/P is an 8-bit RISC PIC12 microcontroller with 3.5KB Flash program memory, 256 bytes of RAM, a 32MHz internal oscillator, and 6 I/O lines, housed in an 8-pin PDIP through-hole package. It belongs to the PIC16(L)F161X family that targets small-motor embedded control, general-purpose logic, low-power edge sensing, and signal-conditioning applications. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, non-volatile program memory (Flash), volatile working memory (RAM), and peripheral blocks onto one die. Within the broader taxonomy, PIC12LF1612 belongs to: microcontroller -> 8-bit MCU -> PIC MCU -> PIC12 family -> low-power (LF) variant. The LF suffix indicates the wide-voltage CMOS process, enabling operation from 1.8V to 3.6V versus 2.3V-5.5V for the standard 'F' part. PIC MCUs use a RISC Harvard architecture with a 14-bit instruction word optimized for deterministic, byte-oriented code density. Key features include 10-bit A/D conversion, a 5-bit DAC, Capture/Compare/PWM (CCP), 24-bit Signal Measurement Timer (SMT), Zero-Cross Detection, angular timer, complementary waveform generator, and on-chip temperature indicator. The internal 32MHz oscillator eliminates external crystals in many designs. The 8-pin PDIP package is a plastic dual-in-line through-hole format compatible with breadboards and hand-soldered prototyping. The PIC12LF1612 uses a 14-bit instruction word RISC core with single-cycle execution except for program branches. Wide operating voltage (1.8V minimum at 16MHz, 2.5V-3.6V at full 32MHz) and integrated peripherals reduce BOM cost. Sleep current in the nanoamp range and active current of a few hundred microampheres make it well suited for battery-powered and energy-harvesting applications. Typical applications include small DC motor control with complementary PWM outputs, fan and pump speed controllers, LED lighting drivers with zero-cross detection, IoT sensor nodes, and general-purpose digital logic replacement. The angular timer and SMT blocks also suit energy metering and power-quality monitoring. Design consideration: route the ICSP programming clock/data lines (ICSPCLK/ICSPDAT) to a programming header, as the LF1612 uses high-voltage ICSP for in-circuit programming. Add a 0.1uF decoupling capacitor adjacent to VDD and consider an additional bulk capacitor if driving PWM directly into inductive loads. This page synthesizes distributor pricing, drop-in alternatives drawn from the PIC12 family and competitive 8-bit MCU lines, and practical design notes that go beyond the manufacturer datasheet to accelerate BOM selection and PCB layout decisions.

RFQ যোগাযোগ
PIC12LF1612-I/SN - 8-Bit 32MHz MCU 3.5KB Flash 8-SOIC | Microchip
PIC12LF1612-I/SN

PIC12LF1612-I/SN - 8-Bit 32MHz MCU 3.5KB Flash 8-SOIC | Microchip

The Microchip Technology PIC12LF1612-I/SN is an 8-bit PIC RISC microcontroller delivering 32MHz CPU performance with 3.5KB (2K x 14) flash program memory in an 8-pin SOIC package. It operates from a 1.8V to 3.6V supply, supports 6 I/O lines, and integrates peripherals including ADC, DAC, PWM, CCP, and Zero-Cross Detection. What is an 8-bit microcontroller? An 8-bit microcontroller (MCU) is a small computer-on-a-chip that processes data 8 bits at a time, integrating a CPU, memory (flash/RAM), and peripherals onto a single die. It belongs to the broader hierarchy: microcontroller -> embedded processor -> semiconductor. 8-bit MCUs dominate cost-sensitive, low-power applications where 32-bit performance is unnecessary. Key features of the PIC12LF1612 include 256 bytes of RAM, a 10-bit ADC with dedicated channels, a 5-bit DAC, enhanced PWM modules, and zero-cross detection for TRIAC control. The device supports in-circuit serial programming (ICSP) and operates over the extended -40C to +85C industrial temperature range with low power consumption suitable for battery-powered designs. The PIC12LF1612 uses Microchip's enhanced mid-range PIC12 core with a hardware multiplier, 16-level stack, and interrupt-driven architecture. Its nanoWatt XLP technology offers sleep currents below 100 nA, making it suitable for energy harvesting or coin-cell applications where every microwatt matters. Typical applications include LED lighting control, small motor drives (PWM + CCP + zero-cross), PIR sensor signal conditioning, AC line voltage zero-cross detection for TRIAC/SCR triggering, capacitive touch sensing via the 5-bit DAC + ADC, and battery-powered IoT sensor nodes. The 1.8V minimum VDD also makes it usable in two-AA-cell designs. When designing with this device, ensure the ICSP programming interface is accessible (PGD/PGC pins on RA0/RA1) and reserve adequate decoupling (100nF + 10uF) near VDD. Watch the absolute maximum VDD of 4.0V; an LDO ahead of the MCU is mandatory when powered from 5V rails. This page synthesizes distributor pricing from DigiKey/Mouser/LCSC, drop-in alternatives (same SOIC-8 footprint), and practical design notes not consolidated on the manufacturer datasheet.

RFQ যোগাযোগ
PIC12LF1612T-I/SN - 8-Bit 32MHz MCU 3.5KB Flash | Microchip
PIC12LF1612T-I/SN

PIC12LF1612T-I/SN - 8-Bit 32MHz MCU 3.5KB Flash | Microchip

The Microchip Technology PIC12LF1612T-I/SN is an 8-bit Flash microcontroller built around the enhanced mid-range PIC12 core, delivering 32 MHz CPU performance with a 125 ns instruction cycle, 3.5 KB (2K x 14) of self-programmable Flash program memory, and 256 bytes of SRAM, all housed in a compact 8-pin SOIC package. It targets embedded control of small motors and general-purpose applications in cost- and space-constrained designs. An 8-bit microcontroller (MCU) is a single-chip computer that integrates an 8-bit CPU, program memory (Flash/ROM), data memory (RAM), and a set of on-chip peripherals (ADC, timers, PWM, I/O). Within the broader semiconductor hierarchy, 8-bit MCUs sit under microcontrollers, which in turn belong to the embedded computing and power management-adjacent integrated circuit family. The PIC12LF1612 is part of Microchip's PIC12F/LF family - a sub-family optimised for low pin count (8 to 14 pins), low power, and small-footprint consumer/industrial applications. Key features include 6 general-purpose I/O pins, a 10-bit Analog-to-Digital Converter (ADC), a 5-bit Digital-to-Analog Converter (DAC), multiple Capture/Compare/PWM (CCP) modules, 24-bit Signal Measurement Timer (SMT) for precise time/capture functions, Zero Cross Detection, a Configurable Logic Cell (CLC), Complementary Waveform Generator (CWG), Numerically Controlled Oscillator (NCO), and on-chip CRC plus a windowed Watchdog Timer (WWDT) for safety-critical support. The 'LF' suffix denotes the wide 1.8V-3.6V VDD range ideal for battery-powered 2xAA/coin-cell designs. Architecturally, the PIC12LF1612 uses Microchip's enhanced mid-range 14-bit instruction set with a hardware stack and single-cycle ALU, allowing deterministic interrupt latency. The CIP (Core Independent Peripherals) like CWG, NCO, and CLC operate without CPU intervention, freeing the core for application logic and reducing firmware complexity while improving EMC behaviour. Typical applications include small DC motor and fan control (PWM + CWG), LED lighting dimming (PWM + Zero Cross Detection), battery-powered IoT sensor nodes, fan/thermostat controllers, consumer appliances, and low-cost general-purpose embedded control boards where 8 pins and 32 MHz are sufficient. When designing with this MCU, observe absolute maximum VDD of 4.0V and use decoupling (100 nF + 1 uF) within 3 mm of VDD/GND. The 'T' suffix denotes Tape & Reel packaging for SMT production lines. This page synthesises distributor pricing, drop-in alternatives, and practical design notes that complement rather than duplicate the manufacturer datasheet.

RFQ যোগাযোগ
PIC12LF1822-E/MF - 8-bit MCU, 3.5KB Flash, 32MHz, XLP | Microchip
PIC12LF1822-E/MF

PIC12LF1822-E/MF - 8-bit MCU, 3.5KB Flash, 32MHz, XLP | Microchip

The Microchip Technology PIC12LF1822-E/MF is an 8-bit PIC® XLP™ flash microcontroller offering 3.5KB (2K x 14) of program memory, 256 bytes of EEPROM, and 128 bytes of RAM in an 8-pin DFN (3x3 mm) package. It runs up to 32 MHz instruction clock from an internal oscillator and supports 1.8V to 3.6V operation, making it a drop-in member of the PIC12(L)F1822/PIC16(L)F1823 family. Per the Microchip datasheet 40001413F, the device delivers nanoWatt XLP extreme-low-power technology with active current below 50 µA/MHz and sleep current in the nanoamp range, targeting battery- and energy-harvesting systems. A PIC microcontroller (MCU) is a compact programmable processor that integrates CPU core, non-volatile flash program memory, SRAM, EEPROM, and peripherals such as ADC, timers, comparators, and communication modules into a single IC. Within the broader taxonomy, the PIC12LF1822 belongs to the enhanced mid-range 8-bit PIC12 family, which sits below the PIC16 and PIC18 lines and above baseline 8-bit cores; XLP nanoWatt technology further classifies it as an ultra-low-power MCU ideal for IoT edge nodes, wearables, and remote sensors where quiescent current is critical. Key features of the PIC12LF1822-E/MF include an integrated 10-bit ADC with up to 7 channels, a 16-bit timer, a 10-bit PWM module, two comparators, an EUSART, and an MSSP module supporting SPI and I²C. The 8-pin DFN (3x3 mm) package gives designers 6 general-purpose I/O pins plus ICSP™/ICD programming access. The 'LF' suffix denotes the low-voltage F variant, and 'E/MF' specifies the industrial temperature grade (-40°C to +125°C) in DFN-8 packaging. Architecture-wise, the device uses a RISC-based PIC core with a single-cycle instruction execution at 200 ns (32 MHz) and a hardware stack supporting deep call nesting. The on-chip 32 MHz HFINTOSC and 31 kHz LFINTOSC eliminate external crystal requirements for many designs. CIPs (Core Independent Peripherals) such as the complementary waveform generator and configurable logic cells let the part handle events without waking the CPU, dramatically reducing average power. Typical applications include battery-powered IoT sensor nodes, wearable fitness/health monitors, remote controls, low-power wireless sensor end nodes (sub-1 GHz, BLE beacons), electronic shelf labels, smart-metering peripherals, and LED driver control loops. The wide 1.8V-3.6V range and DFN-8 footprint also make it attractive for space-constrained consumer and industrial modules. When designing with the PIC12LF1822-E/MF, place a 0.1 µF decoupling capacitor close to VDD and route the ICSPDAT/ICSPCLK lines with short, isolated traces for stable in-circuit debugging. Use the nanoWatt XLP sleep modes (doze, idle, sleep) to bring average current below 50 nA for battery-life-critical designs. The DFN-8 package requires thermal pad soldering per IPC-7351 for reliable production.

RFQ যোগাযোগ
PIC12LF1822-E/P - 8-Bit 32MHz XLP MCU 3.5KB Flash DIP-8
PIC12LF1822-E/P

PIC12LF1822-E/P - 8-Bit 32MHz XLP MCU 3.5KB Flash DIP-8

The Microchip PIC12LF1822-E/P is an 8-bit CMOS flash microcontroller in the PIC® XLP™ 12F family, delivering 32 MHz CPU performance from 3.5 KB (2K x 14) of program flash and 128 bytes of RAM, housed in an 8-pin PDIP through-hole package. The -E temperature grade extends the operating range from -40C to +125C, suitable for industrial and extended-temperature applications. The 'LF' suffix designates the low-voltage variant, supporting operation from 1.8V to 3.6V with Microchip's nanoWatt XLP technology for ultra-low sleep current consumption. A microcontroller (MCU) is a single-chip computer containing a CPU core, program memory (flash/ROM), data memory (RAM), and integrated peripherals such as timers, ADC, communication interfaces, and I/O pins. PIC microcontrollers use a RISC (Reduced Instruction Set Computer) architecture with a 14-bit wide instruction word, providing deterministic execution and compact code density. The PIC12F/LF family targets low pin-count (8-pin) cost-sensitive and space-constrained designs where minimal external components are required. PIC12LF1822 specifically sits in the enhanced mid-range PIC12 family, offering 200 ns instruction execution time at 32 MHz oscillator frequency. Key features include six I/O pins, an internal 32 MHz oscillator, internal 16 MHz HFINTOSC, multiple clock sources with software-selectable frequency, nanoWatt XLP sleep modes (down to ~20 nA typical), an integrated 10-bit ADC with up to 4 channels, 2 comparators, PWM modules, EUSART, MSSP (I2C/SPI), and on-board EEPROM emulation. The wide operating voltage and extreme low power consumption make it appropriate for battery-powered sensor and IoT endpoint designs. Architecture-wise, the PIC12LF1822 uses an enhanced mid-range 8-bit core with hardware multiplier support, interrupt handling with context save/restore, and a 16-level hardware stack. Internal peripherals share pins via peripheral pin select (PPS)-lite functionality, simplifying PCB routing in 8-pin constrained layouts. Typical applications include battery-powered IoT sensor nodes, remote controls, low-power wireless transmitters, LED lighting controllers, small appliance controls, smart home edge devices, and wearable accessories. The nanoWatt XLP feature extends battery life in duty-cycled applications to multi-year spans on coin cells. Designers should evaluate clock source selection and oscillator precision for timing-sensitive applications, since the internal 32 MHz oscillator has ±2% typical accuracy at 3V/25C. For designs requiring higher accuracy, an external crystal can be added, though this uses two I/O pins.

RFQ যোগাযোগ
PIC12LF1822-E/SN - 8-Bit 32MHz XLP MCU 3.5KB Flash | Microchip
PIC12LF1822-E/SN

PIC12LF1822-E/SN - 8-Bit 32MHz XLP MCU 3.5KB Flash | Microchip

The Microchip Technology PIC12LF1822-E/SN is an 8-bit PIC® XLP™ 12F family flash microcontroller delivering 32 MHz CPU performance with 3.5 KB (2K x 14 words) of program Flash memory in an 8-pin SOIC package. It features 128 bytes of RAM, 256 bytes of EEPROM, an integrated 32 MHz internal oscillator, and 6 I/O pins with peripheral pin select (PPS). The 'LF' prefix denotes the low-voltage variant operating from 1.8 V to 3.6 V, optimized for ultra-low-power (XLP) applications. An 8-bit microcontroller (MCU) is a compact, deterministic computing device that integrates a CPU, memory, and peripherals on a single silicon die, forming the lowest tier of the embedded controller hierarchy: 8-bit MCU -> microcontroller -> embedded processor -> semiconductor. The PIC12 architecture uses a modified Harvard RISC core with a 14-bit instruction word, achieving 200 ns instruction execution at 32 MHz, well-suited for sensor interfacing, control loops, and low-power IoT endpoints. Key features include an integrated 32 MHz internal oscillator (no external crystal required), 10-bit ADC with computation (ADC2), multiple timers (Timer0, Timer1, Timer2), enhanced PWM, USART, SPI, and I²C peripherals, plus an on-chip temperature indicator. The device supports nanoWatt XLP sleep currents as low as 20 nA typical, with active currents near 50 µA/MHz at 3.3 V, enabling multi-year battery life in remote sensor nodes. The PIC12LF1822 uses Microchip's enhanced mid-range 8-bit core with single-cycle hardware multiply, hardware CWG (complementary waveform generator), and a four-channel enhanced PWM module. Its nanoWatt XLP technology suite includes low-power sleep, watchdog timer with on-chip LPRC, and ultra-low-power wake-on-change, making it a strong fit for energy-harvesting and always-on applications. Typical applications include IoT sensor nodes, wearable fitness/health bands, remote control key fobs, battery-powered metering, smart-home edge devices, and small motor/LED control boards. Its 1.8 V minimum supply allows direct connection to single-cell alkaline or rechargeable coin cells. When designing with this MCU, ensure VDD decoupling uses a 100 nF ceramic capacitor within 5 mm of the VDD pin, and consider using the internal LFINTOSC instead of an external crystal to minimize BOM cost and PCB area. The ICSP™ programming interface uses pins GP0 (ICSPCLK) and GP1 (ICSPDAT), so reserve these even in production layouts to enable field firmware updates. This page synthesizes distributor pricing (DigiKey, Mouser, LCSC), drop-in same-package alternatives, and engineering design notes that are not available in the manufacturer datasheet alone.

RFQ যোগাযোগ
PIC12LF1822-I/P - 8-bit MCU, 3.5KB Flash, 32MHz XLP | Microchip
PIC12LF1822-I/P

PIC12LF1822-I/P - 8-bit MCU, 3.5KB Flash, 32MHz XLP | Microchip

The Microchip PIC12LF1822-I/P is an 8-bit flash microcontroller based on the enhanced mid-range PIC12 core, delivering 32 MHz (200 ns instruction cycle) performance with 3.5 KB flash program memory, 128 bytes SRAM, and 256 bytes EEPROM in an 8-pin PDIP through-hole package. It features six I/O pins, an integrated 32 MHz internal oscillator, and the nanoWatt XLP (eXtreme Low Power) technology that drops active current to roughly 50 µA/MHz and sleep current down to about 20 nA. An 8-bit microcontroller (MCU) is a small computer on a single integrated circuit containing a CPU, RAM, non-volatile program memory, and I/O peripherals, designed for embedded control tasks. PIC12 microcontrollers belong to Microchip's 8-bit PIC® (Peripheral Interface Controller) family, which sits in the broader taxonomy of microcontrollers -> microprocessors -> semiconductors. Low pin-count PIC12 parts target simple, cost-sensitive, ultra-low-power applications where dedicated logic would be too rigid and a full 32-bit MCU would be over-spec. Key features include one 10-bit ADC with up to 4 input channels, two 8-bit timers plus one 16-bit timer, Enhanced PWM (ECCP) modules, an MSSP peripheral supporting SPI and I2C (both master and slave), an EUSART with LIN support, and an on-chip temperature indicator. The LF silicon supports 1.8V–3.6V operation, making it suitable for single-cell Li-ion, two-AA, and energy-harvesting rails. The part carries an industrial temperature rating of -40 °C to +85 °C. Architecturally, the PIC12LF1822 combines a RISC Harvard CPU with peripheral pin select (PPS) limited to fixed-function pins on the 8-pin package, an internal voltage reference for the ADC, and a configuration that supports in-circuit serial programming (ICSP) plus in-circuit debugging through PICkit 3, MPLAB ICD 3, or the optional AC244044 LF debug header. Typical applications include battery-powered sensor nodes, remote controls, wearable accessories, low-end IoT edge nodes, and consumer appliances that benefit from nanoWatt XLP sleep modes. It is also widely used as a glue controller to offload timing-critical tasks from a host processor, or as a housekeeping MCU providing watchdog and reset functions in larger embedded systems. When designing with this device, budget headroom for the internal oscillator accuracy across temperature (±1% typical at 25 °C, degrading at extremes) and place a 0.1 µF decoupling capacitor close to VDD. For low-noise ADC sampling, configure the part to sleep the CPU before triggering conversions to reduce digital switching noise. This page synthesizes distributor pricing, drop-in pin-compatible alternatives, and practical design notes not found in the manufacturer datasheet, supporting faster sourcing and design-in decisions for the PIC12LF1822-I/P.

RFQ যোগাযোগ
PIC12LF1822-I/SN - 8-bit 32MHz XLP MCU 3.5KB Flash | Microchip
PIC12LF1822-I/SN

PIC12LF1822-I/SN - 8-bit 32MHz XLP MCU 3.5KB Flash | Microchip

The Microchip PIC12LF1822-I/SN is an 8-bit CMOS flash microcontroller built on the enhanced mid-range PIC12 core, delivering 32MHz (200ns instruction cycle) performance from a 2.5V to 3.6V supply in an 8-pin SOIC (SN) package. It integrates 3.5KB Flash program memory, 128 bytes RAM, 256 bytes EEPROM, and 6 I/O pins in a compact nanoWatt XLP package optimized for low-power embedded designs. What is a PIC microcontroller? A PIC (Peripheral Interface Controller) is a family of 8-bit RISC microcontrollers from Microchip Technology built around a Harvard architecture with separate program and data buses. PIC12 microcontrollers are the smallest, lowest-pin-count family (8-pin), positioning them as a sub-family of 8-bit microcontrollers within Microchip's broader portfolio of microcontrollers and digital signal controllers. The "LF" prefix indicates the low-voltage nanoWatt XLP variant, which targets battery-operated and energy-harvesting applications where deep sleep current is critical. Key features of the PIC12LF1822 include an internal 32MHz oscillator (selectable), 4-channel 10-bit ADC, two 8-bit timers plus one 16-bit timer, Enhanced Universal Synchronous Asynchronous Receiver Transmitter (EUSART), and two capture/compare/PWM modules. The nanoWatt XLP technology provides sleep currents as low as 20nA typical (watchdog disabled), making the part suited for always-on IoT endpoints and battery-powered sensor nodes. The integrated ICSP (In-Circuit Serial Programming) interface allows in-system firmware updates without removing the device from the board. Architecturally, the PIC12LF1822 uses a 14-bit instruction word with single-cycle execution except for branches, and provides hardware-level support for interrupt-driven designs with a prioritized interrupt controller. The on-chip voltage reference and fixed voltage reference module give the ADC a stable conversion baseline without external components, while the configurable Weak Pull-Up on each I/O pin reduces external resistor count in button-matrix or keypad interfaces. Typical applications include low-power IoT sensor nodes, battery-powered remote controls, wearable health monitors, automotive interior lighting, and portable consumer electronics. The part is also widely used as a compact system management controller in larger designs, providing housekeeping, watchdog, and housekeeping-power functions. The 6 available I/O pins plus dedicated ICSP pins allow the entire application to be implemented with no additional logic devices. When designing with this device, place a 0.1uF decoupling capacitor as close as possible to the VDD pin and tie all unused I/O pins to defined logic levels (either VDD or VSS) to minimize current leakage. The internal oscillator can be tuned via the OSCTUNE register, and clock switching between internal and external sources is supported at runtime. Programming is performed via the PICKit 3, MPLAB ICD 3, or compatible programmers using the ICSP interface, and the device supports both high-voltage and low-voltage ICSP entry methods. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical low-power design notes not found in the manufacturer datasheet alone. Information gain is provided by the drop-in replacement matrix, nanoWatt XLP sleep current guidance, and application-specific circuit recommendations sourced from Microchip reference designs.

RFQ যোগাযোগ
PIC12LF1822T-I/MF - 8-Bit XLP MCU, 32MHz, 3.5KB Flash, 8-DFN | Microchip
PIC12LF1822T-I/MF

PIC12LF1822T-I/MF - 8-Bit XLP MCU, 32MHz, 3.5KB Flash, 8-DFN | Microchip

The Microchip Technology PIC12LF1822T-I/MF is an 8-bit PIC® XLP™ 12F-series microcontroller built on a nanoWatt XLP (eXtreme Low Power) CMOS process, offering up to 32 MHz CPU clock, 3.5 KB (2K × 14) self-programmable Flash program memory, 128 bytes of SRAM, and 256 bytes of EEPROM in a compact 8-pin 3×3 mm DFN (MF) package. The "LF" suffix denotes the wide 1.8V–3.6V VDD variant, distinguishing it from the 1.8V–5.5V "F" sibling. A microcontroller (MCU) is a single-chip computer containing a CPU, program memory, working RAM, and programmable peripherals on one die. PIC12-series parts are Microchip's low-pin-count 8-bit PIC16/17-architecture microcontrollers optimized for cost- and power-sensitive embedded control. They sit within the hierarchy: PIC12 (sub-family) -> PIC16/PIC18 (mid-range PICs) -> 8-bit PIC microcontrollers -> microcontrollers -> microprocessors -> semiconductors. Key features include five timers (Timer0, Timer1, Timer2 plus two SMT/SRN units), a 4-channel 10-bit ADC with internal voltage reference, a 1-channel 5-bit DAC, a 5-bit DAC reference, two PWM modules with complementary outputs, an Enhanced USART (EUSART) supporting LIN/IrDA, and a Master Synchronous Serial Port (MSSP) configurable for SPI or I²C (master/slave). The device also integrates two comparators, a 32 kHz WDT, brown-out reset, and an on-chip 16 MHz internal oscillator with PLL. The nanoWatt XLP architecture enables typical sleep currents below 50 nA (depending on configuration), making the PIC12LF1822T-I/MF suitable for battery- or energy-harvesting endpoints. The 200 ns instruction execution (5 MIPS at 32 MHz) supports responsive control loops despite the modest clock budget. Peripherals are remappable via Peripheral Pin Select (PPS)-equivalent multiplexers, allowing flexible signal routing in the 8-pin package. Typical applications include low-power IoT sensor nodes, wearable electronics, battery-powered remote controls, LED lighting controllers, and compact industrial sensor front-ends. The 32 MHz internal oscillator with ±1% accuracy (factory calibrated) eliminates an external crystal on most designs, reducing BOM and PCB area. When designing with this part, ensure the chosen VDD falls within 1.8V–3.6V and the in-circuit serial programming (ICSP) lines are accessible for production firmware updates via PICkit™ 3 or MPLAB Snap. Pay attention to the DFN exposed pad thermal/mounting requirements. This page synthesizes XAIPART distributor pricing, 7 drop-in alternatives with quantified key differences, and practical design notes not found on any single distributor product page.

RFQ যোগাযোগ