Analog Devices

ADSP-2115KST-80 - 20 MHz 16-Bit DSP | Analog Devices

MPN: ADSP-2115KST-80 ✓ সক্রিয়
5 V Vdss 80-pin PQFP/TQFP Package 20 MHz Speed
সর্বনিম্ন অর্ডার পরিমাণ: 1 |

ADSP-2115KST-80 সারাংশ

The Analog Devices ADSP-2115KST-80 is a 16-bit fixed-point digital signal processor with a 20 MHz clock, 20 Mips processing rate, one serial port, and an 80-pin PQFP/TQFP package. It belongs to the ADSP-2100 family of DSP microcomputers and combines an enhanced Harvard architecture with separate instruction and dual data buses. The processor is designed for high-speed numeric processing, control, communications, and embedded signal-processing tasks.

A digital signal processor, or DSP, is a semiconductor architecture optimized for arithmetic operations on sampled signals. The ADSP-2100 family combines a 16-bit instruction set, independent computation units, data address generators, on-chip memory, programmable timers, and serial interfaces in a single-chip processor. Its enhanced Harvard organization allows instruction fetches and data transfers to occur concurrently, improving throughput for filtering, modulation, waveform generation, and control algorithms.

The ADSP-2115KST-80 provides a 20 MHz operating clock, a 20 Mips execution rate, a 16-bit fixed-point architecture, and one serial port. The serial interface supports communication with converters, codecs, memories, and other digital peripherals. Its 24-bit external data bus is suited to systems requiring wider data transfer than the internal fixed-point arithmetic word length. The device is manufactured in CMOS and is offered in an 80-pin plastic package.

The ADSP-2100 core separates the program sequencer, arithmetic logic unit, multiplier-accumulator, and shifter into parallel computation resources. This architecture is useful for algorithms that require frequent multiply-accumulate operations, including digital filtering, modulation and demodulation, speech processing, industrial control, and instrumentation. Single-cycle instruction execution and three-bus operation help sustain the stated 20 Mips throughput when the program and data access pattern is designed appropriately.

Typical applications include audio and communications signal processing, motor and power control, industrial measurement, speech-processing modules, embedded communications equipment, and real-time control systems. In these systems, the ADSP-2115KST-80 can execute deterministic numeric routines while using its serial port for converters or external communications. System partitioning should account for external memory timing, DMA requirements, and the fixed-point arithmetic model.

The primary design consideration is timing margin around the external bus and serial interface. Keep address, data, and control routing short, preserve the required clock relationships, and provide the decoupling and grounding arrangement specified by the manufacturer. Because this processor uses an older family architecture, new firmware should be checked carefully against the ADSP-2100 instruction set, linker behavior, and available software tools.

This product page combines the documented processor identity, package information, architecture characteristics, sourcing guidance, application fit, and engineering cautions into a design-oriented reference. It also distinguishes the verified drop-in candidate from unsupported substitutions, helping teams evaluate PCB reuse without assuming that a similar-sounding part is electrically interchangeable.

এর জন্য ড্রপ-ইন বিকল্প ADSP-2115KST-80 — একই package, pin-to-pin compatible। ভিন্ন package-এর যেসব পার্টে PCB rework প্রয়োজন সেগুলো বাদ দেওয়া হয়েছে।

ADSP-2115KP-80

✅ ড্রপ-ইন
📦 80-pin PQFP/TQFP
Same ADSP-2115 family and 80-pin package class; the documented difference is the K versus P ordering suffix, with exact speed and temperature details requiring datasheet confirmation.

📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)

ADSP-2115KST-80 বিশেষণ

Product Type 16-bit fixed-point DSP microprocessor
Clock Frequency 20 MHz
Instruction Throughput 20 Mips
DSP Word Length 16 bit
External Data Bus Width 24 bit
Architecture Enhanced Harvard architecture
Program Bus Configuration 1 instruction bus
Data Bus Configuration 2 data buses
Computation Units ALU, multiplier/accumulator, and shifter
Serial Port Count 1
সাপ্লাই ভোল্টেজ 5 V
Process Technology CMOS
Package Type 80-pin PQFP/TQFP
Package Category Surface-mount plastic package

ADSP-2115KST-80 surface-mount plastic package পিন কনফিগারেশন গাইড

ADSP-2115KST-80 (surface-mount plastic package প্যাকেজ)-এর পিন কনফিগারেশন। পিন নম্বরিং, ফাংশন এবং সংযোগ ডায়াগ্রাম প্রস্তুতকারকের ডেটাশিটে সংজ্ঞায়িত করা আছে। সঠিক ফুটপ্রিন্ট এবং সোল্ডারিং নির্দেশিকার জন্য এটি দেখুন।

ADSP-2115KST-80-এর জন্য surface-mount plastic package প্যাকেজ পিনআউট ডায়াগ্রাম

এর জন্য বিস্তারিত পিনআউট ডেটা পাওয়া যায়নি ADSP-2115KST-80.

দেখুন ডেটাশিট সম্পূর্ণ পিন কনফিগারেশনের জন্য।

সাধারণ ব্যবহার

ADSP-2115KST-80 এর জন্য উপযুক্ত 6 অ্যাপ্লিকেশনs: Audio Signal Processing, Industrial Motor Control, Communications Modulation, Industrial Measurement and Instrumentation, Speech Processing, Real-Time Control and Waveform Generation.

🎧

Audio Signal Processing

The ADSP-2115KST-80 fits audio filtering, mixing, equalization, modulation, and effects processing because its 16-bit fixed-point DSP core runs at 20 MHz with 20 Mips throughput. The multiplier-accumulator and shifter support common audio arithmetic, while the enhanced Harvard architecture permits instruction fetches and dual data-bus transfers to proceed concurrently. Its one serial port can connect to an audio codec or converter, but the clocking and data format must match that peripheral. Use the manufacturer datasheet to confirm codec timing, serial-port modes, and external-memory requirements for the selected architecture.

🏭

Industrial Motor Control

The ADSP-2115KST-80 is appropriate for deterministic motor-control algorithms that combine filtering with multiply-accumulate calculations at a 20 MHz clock. Its enhanced Harvard organization helps support the instruction and data movement required by current-loop and transform algorithms, while the 16-bit fixed-point format supports efficient integer and scaled arithmetic. The processor should operate behind isolated sensing, power-stage, and gate-driver circuitry. Firmware developers must define scaling, saturation, update timing, and fault handling, and hardware engineers must verify the external bus and serial peripheral timing against the manufacturer datasheet.

🌐

Communications Modulation

The ADSP-2115KST-80 supports communications modulation and demodulation routines that benefit from the 20 Mips fixed-point throughput and independent ALU, multiplier-accumulator, and shifter units. Filtering, symbol processing, carrier generation, and data-rate conversion can be implemented in a compact real-time architecture. The one serial port may connect to a radio or codec, although high-rate parallel interfaces can require external logic. Validate interrupt latency, DMA assumptions, memory bandwidth, and clock recovery against the ADSP-2100 family documentation before fixing the system architecture.

🔧

Industrial Measurement and Instrumentation

The ADSP-2115KST-80 can perform real-time acquisition conditioning, digital filtering, calibration, and numeric analysis in measurement equipment. Its 24-bit external data bus accommodates wider data transfers, while the DSP core executes filtering and arithmetic at 20 Mips. The serial port can be used with suitable converters or control peripherals. Design the analog front end for the required accuracy and bandwidth, then use deterministic timing and calibrated scaling to control conversion error. Verify electrical limits, memory access timing, and peripheral connections in the manufacturer datasheet.

📱

Speech Processing

The ADSP-2115KST-80 is suitable for fixed-point speech filtering, feature extraction, recognition processing, and communication-codec workloads because its computation units can handle frequent multiply-accumulate and shifting operations. The 20 MHz clock and 20 Mips throughput allow deterministic routines without a separate accelerator, while on-chip memory and serial connectivity support compact embedded implementations. Model fixed-point coefficients carefully to control overflow and quantization error. Confirm program-memory capacity, data-memory organization, serial-port modes, and development-tool support before committing to a new speech-processing design.

📺

Real-Time Control and Waveform Generation

The ADSP-2115KST-80 supports deterministic control loops, waveform tables, digital oscillators, and programmable signal generation where fixed-point arithmetic and predictable instruction throughput are important. The independent shifter is useful for scaling and bit manipulation, and the multiplier-accumulator supports loop-intensive filtering and waveform calculations. Use timer interrupts or the documented real-time interrupt mechanism to establish update rates. Validate output latency, jitter, timer resolution, and external-memory timing in the target system because application code and bus activity determine practical execution performance.

What are the key specifications of ADSP-2115KST-80 that engineers should know?
The ADSP-2115KST-80 is a 16-bit fixed-point DSP microprocessor operating at 20 MHz and delivering 20 Mips of instruction throughput. It uses an enhanced Harvard architecture with one instruction bus, two data buses, and independent ALU, multiplier-accumulator, and shifter units. The device has one serial port, a 24-bit external data bus, CMOS construction, and an 80-pin PQFP/TQFP package. Analog Devices describes the ADSP-21xx processors as sharing a common core and differing in memory, timer, serial-port, and host-interface resources.
What is the ADSP-2115KST-80 used for?
The ADSP-2115KST-80 is used for real-time numeric processing in audio, communications, industrial control, measurement, and embedded DSP systems. Its 20 MHz clock, 20 Mips throughput, multiplier-accumulator, shifter, and dual data buses suit filters, modulation, waveform generation, and control algorithms. The one serial port can connect the processor to converters, codecs, memories, or communications peripherals. According to the Analog Devices ADSP-2115 product page, the ADSP-21xx family is optimized for digital signal processing and other high-speed numeric workloads.
What is the processing architecture of ADSP-2115KST-80?
The ADSP-2115KST-80 uses the ADSP-2100 family enhanced Harvard architecture with one instruction bus and two independent data buses. Its computation resources include an arithmetic logic unit, a multiplier-accumulator, and a shifter, while separate data address generators support data movement. This organization allows instruction execution and data transfers to overlap, which is valuable in signal-processing loops dominated by multiply-accumulate operations. Analog Devices identifies the common ADSP-21xx core as combining the DSP computation units, data address generators, and program sequencer.
Where can I download the ADSP-2115KST-80 datasheet PDF?
The official ADSP-2115KST-80 documentation is available through the Analog Devices ADSP-2115 product page at https://www.analog.com/en/products/adsp-2115.html. That page is the preferred starting point for the current manufacturer datasheet, product status, and family information. A separate ADSP-2100 family datasheet listing is also accessible through the ADSP-2115KST-80 datasheet result on alldatasheet.com. Always check the Analog Devices page first when pin assignments, timing, memory, or electrical characteristics are needed for a new design.
Where can I find the ADSP-2115KST-80 pinout?
The ADSP-2115KST-80 pinout is defined by the pin-description table in the Analog Devices ADSP-2100 family documentation linked from the official ADSP-2115 product page. Use that table to assign all 80 package pins before laying out a replacement PCB. Do not infer unused or alternate-function pins from a generic QFP symbol. The public product summary confirms the 80-pin package and device identity, but it does not provide a complete numbered pin table, so consult the manufacturer datasheet for authoritative signal names and pin numbers.
How much current does the ADSP-2115KST-80 consume?
The ADSP-2115KST-80 is a 5 V CMOS DSP, but its exact operating-current specifications cannot be stated reliably without the electrical-characteristics table in the manufacturer datasheet. Current consumption depends on clock activity, processor instruction mix, memory access, I/O activity, and voltage. Use the datasheet's core, I/O, and total supply-current limits for worst-case power budgeting, and account separately for external memory and interface loads. The same caution applies to power dissipation because the package thermal behavior depends on the assembled board and switching activity.
Is ADSP-2115KST-80 suitable for audio signal processing?
The ADSP-2115KST-80 is suitable for many fixed-point audio processing functions because it provides a 16-bit DSP architecture, 20 Mips throughput, a multiplier-accumulator, and one serial port for converter or codec connectivity. Filters, mixing, equalization, modulation, and effects algorithms can benefit from concurrent instruction and dual-data-bus access. The exact converter, codec, sample rate, and clock topology must still be designed around the datasheet's timing and pin requirements, especially when external memory or high-speed serial conversion is required.
Can ADSP-2115KP-80 replace ADSP-2115KST-80?
The ADSP-2115KP-80 is the closest documented drop-in candidate for the ADSP-2115KST-80 because it is identified within the same ADSP-2115 family and uses the same 80-pin package naming. The suffix difference typically indicates package or temperature-ordering variation, but the manufacturer datasheet must be checked for the exact pinout, speed grade, temperature range, and ordering codes. Treat the ADSP-2115KP-80 as a candidate requiring qualification, not as an automatic substitute without comparing those four characteristics.
What is the best drop-in replacement for ADSP-2115KST-80?
The ADSP-2115KP-80 is the best-supported drop-in candidate identified for the ADSP-2115KST-80 because it belongs to the same ADSP-2115 device family and appears with an 80-pin package designation. Confirm that the K and P package codes, processor speed, temperature grade, and exposed or non-exposed thermal-pad configuration match before releasing a replacement. No cross-brand part was established as pin-compatible through the available cross-reference results, so selecting a different manufacturer would require a complete PCB and firmware compatibility review.
When should I choose ADSP-2115KST-80 over another DSP?
Choose the ADSP-2115KST-80 when a legacy design specifically uses the ADSP-2100 instruction set, requires its 20 MHz fixed-point processing characteristics, and benefits from maintaining an existing 80-pin board design. It is particularly appropriate when replacing a failing original component without changing code, memory interfaces, or board layout. For new high-complexity designs, compare modern DSPs on floating-point support, memory bandwidth, development tools, peripherals, power, and software ecosystem rather than selecting only by clock frequency or package size.
Is ADSP-2115KST-80 the same as ADSP-2115KP-80?
The ADSP-2115KST-80 and ADSP-2115KP-80 are closely related ADSP-2115-family configurations, but they are not identical orderable MPNs. The available documentation identifies both as 80-pin devices and identifies the KP part in the same family, which makes the KP candidate relevant to a drop-in evaluation. Before substitution, compare the manufacturer ordering table for package construction, temperature grade, clock rating, and pin compatibility. A shared package count alone does not prove that every pin, pad, and operating limit is identical.
ADSP-2115KST-80 vs ADSP-2115KP-80: which is better for an existing board?
The ADSP-2115KP-80 is generally the better replacement candidate for an existing ADSP-2115KST-80 board because the cross-reference results associate it with the same ADSP-2115 family and 80-pin package class. The better choice is whichever ordering code exactly matches the board's pin configuration, speed grade, and temperature requirements. Compare the original purchasing code and the manufacturer datasheet before installation, then validate reset, clock, memory, serial-port, and interrupt behavior in the finished system.
Can I use ADSP-2115KST-80 for industrial motor control?
The ADSP-2115KST-80 can serve as the real-time numeric controller in an industrial motor-control system because its fixed-point DSP core, multiplier-accumulator, and enhanced Harvard architecture suit control loops and signal processing. The practical design must include suitable analog front ends, isolated gate drivers, current and position sensing, deterministic timing, and appropriate protection. The processor is only one element of the control chain, so motor safety, fault handling, and electrical isolation must be designed and validated independently.
What software tools are available for ADSP-2115KST-80?
The ADSP-2115KST-80 belongs to the ADSP-2100 family, so supported development tools are the key consideration for firmware migration and maintenance. A workable toolchain must generate code for the ADSP-2100 architecture, support its assembly and linking conventions, and provide debugging for the installed part. The available product information confirms the processor family but does not enumerate a specific current tool version. Confirm simulator, emulator, linker, and library compatibility with Analog Devices before beginning production software work.
Where can I buy ADSP-2115KST-80 and what is its lead time?
Use the Request a Quote form on this page to request ADSP-2115KST-80 availability, current lead time, order quantity, and delivery options for your project. The request should include the exact MPN, required quantity, target date, and whether you need an authorized purchase channel. The available listings do not provide a qualifying quantity-break price table for this exact MPN, and no stock commitment should be inferred from general marketplace pages. Confirm lifecycle, traceability, and packaging requirements during quotation.
What is the price of ADSP-2115KST-80?
The current ADSP-2115KST-80 price depends on order quantity, packaging form, stock position, and required sourcing channel. Use the Request a Quote form on this page to obtain a current quotation for the exact MPN rather than relying on a stale market-page figure. Include the quantity schedule, target date, and any authorized-distribution or traceability requirements with the request. This approach also allows the supplier to confirm whether the 80-pin device is available in the required package and temperature grade.
Is ADSP-2115KST-80 in stock?
ADSP-2115KST-80 inventory should be treated as request-specific because availability can change with market conditions and order volume. Submit the exact MPN and required quantity through the Request a Quote form on this page to obtain a current stock and dispatch response. General listing pages do not establish a reliable stock commitment for your order. If uninterrupted production is important, request confirmation of lifecycle status, allocation, and any manufacturer change notifications before placing the order.

এর জন্য ইঞ্জিনিয়ারিং রেফারেন্স ডেটা ADSP-2115KST-80 — তুলনা, ডিজাইন গাইডেন্স এবং কমপ্লায়েন্স তথ্য।

নির্বাচন গাইড

Choose the ADSP-2115KST-80 when repairing or maintaining an existing ADSP-2100-based design that requires the documented 20 MHz clock, 20 Mips throughput, 16-bit fixed-point architecture, one serial port, and 80-pin package. It is the conservative choice when maintaining original ordering-code traceability is important. Consider ADSP-2115KP-80 when the manufacturer ordering information confirms matching speed, temperature grade, package construction, and pin configuration. For a new high-performance design, evaluate current DSPs based on floating-point capability, memory bandwidth, development tools, power, and software ecosystem rather than assuming that this legacy processor is the best architectural fit. No cross-brand drop-in substitute is recommended without a completed pin, clock, memory, peripheral, and firmware compatibility review.

বিকল্পের সাথে তুলনা

পারামিটার এই পণ্য ADSP-2115KP-80
Brand Analog Devices Analog Devices
Package 80-pin PQFP/TQFP 80-pin PQFP/TQFP
Product Family ADSP-2115 ADSP-2115
Processor Type 16-bit fixed-point DSP microprocessor ADSP-2100 family DSP microprocessor
DSP Word Length 16 bit 16 bit

মূল পার্থক্যসমূহ

  • Directly identified ADSP-2115 family replacement path (বনামADSP-2115KP-80)
  • 20 Mips fixed-point processing rate (বনামADSP-2115KP-80)
  • Single-port serial connectivity (বনামADSP-2115KP-80)

ডিজাইন নোট

Treat the ADSP-2100 external buses as timing-critical routes. Keep processor address, data, and control connections short, use the package geometry and reference connectivity specified by the manufacturer, and avoid long stubs that interfere with the 20 MHz system clock. Decouple each supply rail at the package pins and provide a low-impedance return path. Because the public product summary does not include the complete pin table, use the manufacturer pin-description and layout guidance before assigning every signal.

Pay particular attention to clock, reset, and interrupt timing when replacing an existing processor. Confirm that the replacement device's pin functions, clock specification, and input thresholds match the original board before power-up. Series damping or additional source termination should be added only after measuring ringing or overshoot on the installed PCB. The 24-bit external bus and 20 MHz clock require clean reference-clock routing and sufficient ground-plane continuity.

Do not treat a shared 80-pin package name as proof of drop-in equivalence. For the ADSP-2115KP-80 candidate, verify package construction, exposed-pad requirements, speed grade, temperature range, memory organization, serial-port mapping, and every pin assignment against the manufacturer ordering information. Also confirm that the existing linker configuration, boot or reset sequence, and debugger configuration target the correct ordering code.

Budget power from the manufacturer's core, I/O, and total current limits, then add external memory, converters, and interface loads. The 5 V CMOS operating voltage does not by itself determine dissipated power because activity and clocking dominate. Use the datasheet operating-current conditions and measure representative workloads. Keep the switching supply layout compact, preserve the recommended input and bulk-capacitor arrangement, and provide adequate copper for thermal dissipation.

Validate numerical scaling and saturation in fixed-point DSP code. Multiplier-accumulator results can require additional guard bits, and intermediate overflow can corrupt an otherwise mathematically correct filter or control calculation. Use the ADSP-2100 development tools for realistic cycle-count and instruction-set testing, and include worst-case data patterns in system validation rather than testing only zero-input conditions.

কমপ্লায়েন্স তথ্য

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
লিড ফ্রি
Unknown
হ্যালোজেন ফ্রি
Unknown
কনফ্লিক্ট মিনারেলস
Unknown

The available product information identifies CMOS construction and an 80-pin PQFP/TQFP package but does not state RoHS, REACH, lead-free, halogen-free, conflict-minerals, or automotive qualification status.

ডেটা যাচাই করা হয়েছে: 2026-11-10 — ডেটা XAIPART-এর কম্পোনেন্ট ইঞ্জিনিয়ারিং টিম দ্বারা যাচাই ও কিউরেট করা হয়েছে

সম্পর্কিত অনুসন্ধান

ADSP-2115KST-80 datasheet ADSP-2115KST-80 datasheet pdf ADSP-2115KST-80 pinout ADSP-2115KST-80 specifications ADSP-2115KST-80 price ADSP-2115KST-80 stock ADSP-2115KST-80 equivalent ADSP-2115KST-80 replacement ADSP-2115KST-80 cross reference ADSP-2115KST-80 vs ADSP-2115KP-80 ADSP-2115KST-80 TQFP-80 footprint Analog Devices ADSP-2115KST-80

সম্পর্কিত কম্পোনেন্ট ও শর্তাবলী

Analog Devices ADSP-2115KST-80 ADSP-2115KP-80 ADSP-2115 ADSP-2100 family digital signal processor DSP microprocessor fixed-point arithmetic 16-bit DSP enhanced Harvard architecture instruction bus dual data buses arithmetic logic unit multiplier-accumulator shifter 20 MHz 20 Mips 24-bit external data bus serial port PQFP-80 TQFP-80 surface-mount package CMOS audio signal processing industrial motor control
তাৎক্ষণিক বিলওয়াছে রেকোজিউইট
সম্পূর্ণ বিবরণ পূরণ করুন — আমাদের সেলস টিম 24 ঘণ্টার মধ্যে উত্তর দেবে
পার্ট নম্বর উৎপাদক প্যাকেজ QTY লক্ষ্যমূল্য প্রসারিত
✓
বিল প্রস্তুত করা হয়েছে!

আমরা ২৪ ঘণ্টার মধ্যে আপনার ইমেইলে প্রত্যুত্তর দেব

1
RFQ জমা হয়েছে
2
কোটেশন পাওয়া গেছে
3
অর্ডার দেওয়া হয়েছে
4
পেমেন্ট
5
শিপ করা হয়েছে
6
ডেলিভারি হয়েছে
RFQ বিবরণ দেখুন