Microchip Technology

ATTINY1634-MN - 12MHz 8-bit AVR 16KB MCU | Microchip Technology

MPN: ATTINY1634-MN ✓ সক্রিয়
1.8 V to 5.5 V Vdss 20-QFN exposed-pad, 4 x 4 mm Package 12 MHz Speed 16 KB (16K x 8) Memory
সর্বনিম্ন অর্ডার পরিমাণ: 1 |

ATTINY1634-MN সারাংশ

The Microchip Technology ATTINY1634-MN is a low-power CMOS 8-bit AVR microcontroller based on the AVR enhanced RISC architecture, operating at up to 12 MHz with 16 KB of Flash memory in a 20-QFN exposed-pad package. It combines 16K x 8 Flash, 256 B EEPROM, 1 KB SRAM and 18 general-purpose I/O lines in a compact 4 x 4 mm surface-mount package.

An 8-bit AVR microcontroller is a compact embedded-control device that executes instructions using an enhanced RISC core, typically approaching 1 MIPS per MHz. The ATtiny family sits within the broader hierarchy of embedded processors, microcontrollers, embedded controllers and semiconductors. The ATTINY1634 is designed for low-power control tasks where local processing, serial communication, timing and mixed-signal control are needed without a high-cost MCU platform.

Key device capabilities include a 12 MHz maximum clock, 16 KB Flash, 256 B EEPROM, 1 KB SRAM, 18 general-purpose I/O lines, 32 general-purpose working registers, one 8-bit timer/counter, one 16-bit timer/counter, two full-duplex USARTs with Start Frame Detection, a Universal Serial Interface, I2C slave support and internal and external interrupts. These resources make the MCU suitable for compact control boards, industrial modules and embedded peripherals.

The AVR enhanced RISC architecture provides an instruction-oriented balance between processing throughput and power efficiency. At the rated 12 MHz operating point, the architecture can approach 1 MIPS, while the low-power CMOS design supports applications that alternate between active processing and reduced-power operating states. The combination of dual USARTs, USI and I2C allows the device to bridge several common embedded serial interfaces without requiring large numbers of external peripheral ICs.

Typical uses include industrial sensing and control, compact serial gateways, sensor-hub controllers, battery-powered instrumentation, communication modules and small automation nodes. Its 18 I/O lines also permit direct interface connections to sensors, displays, relays and digital logic. The 20-QFN exposed-pad package supports dense PCB layouts, although careful thermal-pad soldering and layout practices are important for reliable assembly.

Designers should verify the complete pin-assignment table in the manufacturer datasheet before routing the PCB, particularly for the exposed pad, power pins, reset and communications functions. Decoupling requirements, clock stability, programming access, I2C address configuration and USART logic levels should also be checked against the device documentation and the selected operating voltage.

This product page consolidates the exact ATTINY1634-MN technical identity, verified listing information, package details and engineering guidance into one focused reference for embedded-system design.

এর জন্য ড্রপ-ইন বিকল্প ATTINY1634-MN — একই package, pin-to-pin compatible। ভিন্ন package-এর যেসব পার্টে PCB rework প্রয়োজন সেগুলো বাদ দেওয়া হয়েছে।

ATTINY1634-15XZ

✅ ড্রপ-ইন
📦 20-QFN exposed-pad, 4 x 4 mm
Ordering code differs from ATTINY1634-MN; the cross-reference result identifies a related ATtiny1634 device, while detailed pin and parameter equality require final manufacturer-document review

📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)

ATTINY1634-MN সর্বোচ্চ রেটিং ও বৈদ্যুতিক বৈশিষ্ট্য

Product Type 8-bit AVR microcontroller
Architecture AVR enhanced RISC
সর্বোচ্চ ক্লক ফ্রিকোয়েন্সি 12 MHz
Flash Memory 16 KB (16K x 8)
EEPROM Memory 256 B
SRAM 1 KB
General-Purpose I/O Lines 18
General-Purpose Working Registers 32
Timer/Counters One 8-bit and one 16-bit timer/counter
Serial Interfaces Two USARTs, USI and I2C slave
Operating Voltage Range 1.8 V to 5.5 V
অপারেটিং তাপমাত্রার পরিসর -40 °C to +105 °C (TA)
প্যাকেজ 20-QFN exposed-pad, 4 x 4 mm
মাউন্টিং টাইপ Surface mount
Core Processor AVR 8-bit
Instruction Throughput Approaching 1 MIPS per MHz
RoHS স্ট্যাটাস Compliant

ATTINY1634-MN 20-qfn exposed-pad, 4 x 4 mm পিন কনফিগারেশন গাইড

ATTINY1634-MN (20-qfn exposed-pad, 4 x 4 mm প্যাকেজ)-এর পিন কনফিগারেশন। এই ডিজিটাল IC-তে GPIO, কমিউনিকেশন ইন্টারফেস (UART, SPI, I2C) এবং পাওয়ার পিন রয়েছে। বিকল্প পিন ফাংশন ও কনফিগারেশন অপশনের জন্য প্রস্তুতকারকের ডেটাশিট দেখুন। এমবেডেড সিস্টেম ডিজাইন ও PCB লেআউটের জন্য অপরিহার্য।

ATTINY1634-MN-এর জন্য 20-qfn exposed-pad, 4 x 4 mm প্যাকেজ পিনআউট ডায়াগ্রাম

এর জন্য বিস্তারিত পিনআউট ডেটা পাওয়া যায়নি ATTINY1634-MN.

দেখুন ডেটাশিট সম্পূর্ণ পিন কনফিগারেশনের জন্য।

সাধারণ ব্যবহার

ATTINY1634-MN এর জন্য উপযুক্ত 6 অ্যাপ্লিকেশনs: Industrial Sensor and Control Node, Serial Communication Gateway, Battery-Powered Instrumentation, Compact Motor and Actuator Controller, Connected IoT Sensor Module, Automated Test and Measurement Equipment.

🏭

Industrial Sensor and Control Node

The ATTINY1634-MN fits compact industrial sensing nodes because it combines 18 general-purpose I/O lines, a 12 MHz AVR core, two USARTs and I2C slave support in a 4 x 4 mm 20-QFN package. It can acquire sensor inputs, apply thresholding or filtering, control discrete outputs and forward measurements through a serial uplink. The 16 KB Flash supports a dedicated control and communications firmware, while 1 KB SRAM is adequate for compact protocol buffers and working variables. At a 1.8 V to 5.5 V supply range, the device accommodates industrial interface levels, although level translation and isolation may still be required. Firmware should use the internal or external clock configuration appropriate to accuracy, latency and power objectives.

🌐

Serial Communication Gateway

The ATTINY1634-MN is appropriate for a small serial gateway because it provides two full-duplex USARTs with Start Frame Detection, a Universal Serial Interface and I2C slave capability. Firmware can bridge a local sensor bus to an upstream host, validate incoming frames, maintain counters and report status without a larger communications processor. Its 16 KB Flash provides room for protocol conversion and diagnostics, while the 1 KB SRAM can support bounded buffering. The two USARTs permit simultaneous host and field-device links when the selected pin multiplexing and peripheral configuration support the intended traffic. Clock accuracy, baud-rate tolerance, logic thresholds and connector protection should be validated for each communication standard.

🧩

Battery-Powered Instrumentation

The ATTINY1634-MN can serve as the control core in battery-powered instrumentation because it is a low-power CMOS 8-bit AVR microcontroller that operates from 1.8 V to 5.5 V. Its 12 MHz maximum clock provides ample throughput for sampling, control and low-volume serial reporting, while sleep modes can reduce consumption between measurements. The device offers 18 I/O lines for sensor enables, status indicators and measurement triggers, plus two USARTs for configuration and data transfer. Firmware should measure the complete system sleep current, disable unused peripherals and select the lowest practical clock rate. The 16 KB Flash limit must also be considered when combining logging, communications and safety diagnostics.

⚡

Compact Motor and Actuator Controller

The ATTINY1634-MN is suitable for compact actuator-control modules where a small controller must coordinate inputs, timers and external drivers. Its 18 general-purpose I/O lines can handle position sensors, limit switches, status LEDs and driver-control signals, while the 8-bit and 16-bit timers support event counting, timing and periodic control tasks. The 12 MHz AVR core and 16 KB Flash are sufficient for deterministic supervisory logic, but motor transients and inductive loads require suitable driver stages, flyback paths, bulk capacitance and protection. The MCU should not directly switch high-current motor windings unless its absolute maximum ratings explicitly permit the application. Firmware should include startup limits and fault handling, and the exposed pad must be connected according to the package guidance.

🧩

Connected IoT Sensor Module

The ATTINY1634-MN fits connected IoT sensor modules that need local sensing, protocol handling and simple control before data reaches a wireless companion. Its 18 I/O lines can interface with environmental or motion sensors, the two USARTs support low-rate telemetry and configuration, and the USI provides additional serial flexibility. The 1 KB SRAM and 16 KB Flash favor event-based rather than buffered high-bandwidth workloads, making the controller effective as a sensor-hub front end rather than a multimedia processor. A 1.8 V operating configuration can reduce power use when the connected module supports it. Firmware should define retry behavior, sensor timeout handling and low-power wake logic, while the PCB should isolate sensitive analog inputs from switching and radio circuitry.

🖥️

Automated Test and Measurement Equipment

The ATTINY1634-MN can coordinate low-level test and measurement fixtures where sequencing, stimulus control and host communication are required. Two USARTs allow separate control and logging channels, the timers support accurate event timing and the 18 I/O lines can control relays, digital stimulus lines and status indicators. Firmware can execute test steps, record pass or fail results and report them to a host controller. Its 16 KB Flash is appropriate for moderate test-sequence logic, while the 1 KB SRAM limits large result buffering. The 1.8 V to 5.5 V operating range supports different fixture architectures, but signal conditioning, protection and grounding remain essential. Calibration data and fault checks should be implemented outside the MCU where greater storage or precision is needed.

What is the ATTINY1634-MN?
The ATTINY1634-MN is a Microchip Technology low-power CMOS 8-bit AVR microcontroller with 16 KB Flash, 256 B EEPROM, 1 KB SRAM and 18 general-purpose I/O lines. According to the Microchip ATtiny1634 product page, it is based on the AVR enhanced RISC architecture and combines two USARTs, a USI, I2C slave support and one 8-bit plus one 16-bit timer/counter.
What is the maximum clock frequency of ATTINY1634-MN?
The ATTINY1634-MN supports a maximum clock frequency of 12 MHz. The manufacturer documentation describes the AVR enhanced RISC architecture as approaching 1 MIPS per MHz, giving the device an instruction-throughput profile suitable for compact embedded-control and serial-communication tasks without requiring a higher-performance MCU architecture.
How much memory does ATTINY1634-MN have?
The ATTINY1634-MN provides 16 KB of Flash program memory, 256 B of EEPROM and 1 KB of SRAM. These resources match the Microchip ATtiny1634 product-page specification and are appropriate for control firmware, parameter storage, serial protocol handling and moderate working-buffer requirements in embedded systems.
What is the ATTINY1634-MN package?
The ATTINY1634-MN is supplied in a 20-QFN exposed-pad package measuring 4 x 4 mm. The exposed pad is part of the package thermal and electrical design, so the PCB footprint should follow the manufacturer land-pattern guidance. Use the manufacturer pin-description table when assigning tracks and confirming exposed-pad connectivity.
What operating voltage does ATTINY1634-MN support?
The ATTINY1634-MN operates from 1.8 V to 5.5 V. This range supports both low-voltage energy-efficient designs and conventional 3.3 V or 5 V systems. Confirm the selected clock configuration, operating mode and peripheral requirements against the datasheet when operating near the range limits.
Where can I download the ATTINY1634-MN datasheet PDF?
The official Microchip ATtiny1634 product page provides the manufacturer datasheet and technical documentation. A directly indexed PDF is also available from Digi Electronics at https://pdf.digi-electronics.com/pdf/2190/ATTINY1634MN-datasheet.pdf. For design authority, use the Microchip copy whenever a revision difference could affect peripheral behavior or electrical limits.
Where can I find the ATTINY1634-MN pinout?
The ATTINY1634-MN pinout is documented in the manufacturer pin-description table for the 20-QFN exposed-pad package. Use that table to verify every ball assignment, including power, ground, reset, programming and exposed-pad connections. The package drawing should be used alongside the schematic because physical orientation alone does not define the signal function.
What communication interfaces does ATTINY1634-MN include?
The ATTINY1634-MN includes two full-duplex USARTs with Start Frame Detection, a Universal Serial Interface and I2C slave functionality. According to the Microchip product page, these interfaces support compact designs that must communicate with sensors, host controllers, converters or other embedded peripherals using multiple serial protocols.
Can ATTINY1634-MN replace ATTINY1634-15XZ?
The ATTINY1634-15XZ appears in a component cross-reference result for the ATTINY1634, but the returned material does not establish a complete pin-to-pin comparison. Do not approve it as a drop-in replacement without checking the exact package drawing, pin table, operating-voltage limits, memory organization and peripheral behavior in the manufacturer documentation for both orderable parts.
What can replace ATTINY1634-MN?
No independently verified, pin-compatible replacement was established for the ATTINY1634-MN. A valid replacement must match the 20-QFN exposed-pad footprint, pin functions, 1.8 V to 5.5 V operating range, memory map, clock behavior, interrupt vector layout and communication peripherals. Request a controlled alternate list through the Request a Quote form for current sourcing and engineering review.
Is ATTINY1634-MN suitable for low-power embedded control?
Yes, the ATTINY1634-MN is suitable for low-power embedded-control designs because it is a low-power CMOS 8-bit microcontroller with a 12 MHz maximum clock and 18 I/O lines. Its sleep and power-management behavior should be configured in firmware, while the selected operating voltage and clock mode must be validated against the manufacturer datasheet.
ATTINY1634-MN vs ATTINY1634-MNR: which package variant should I use?
ATTINY1634-MN and ATTINY1634-MNR identify different orderable packing configurations of the ATtiny1634 family rather than materially different controller functions. Because MNR is a packing-code variant, it should not be treated as a separate engineering alternative. Confirm reel, tray and tape-and-reel requirements with the current Microchip ordering information before procurement.
Where can I buy ATTINY1634-MN online?
Use the Request a Quote form on this page to request current ATTINY1634-MN availability, lead time and order quantities. The form allows buyers to identify the exact package and packing configuration without relying on a generic listing page. Confirm authorized sourcing, traceability and delivery terms before releasing a production order.
What is the price of ATTINY1634-MN?
The current commercial price for ATTINY1634-MN should be obtained through the Request a Quote form on this page because pricing depends on order quantity, package, packing configuration and sourcing conditions. The structured pricing fields are maintained separately so that the displayed product content does not present a stale price as current.
What is the lead time for ATTINY1634-MN?
The current lead time for ATTINY1634-MN should be requested through the Request a Quote form on this page. Include the required quantity, date code requirements and acceptable packaging configuration with the request. For new production designs, also request lifecycle confirmation so the purchasing decision is based on the current manufacturer status.
Is ATTINY1634-MN in stock?
Current ATTINY1634-MN inventory should be confirmed through the Request a Quote form on this page because distributor stock levels can change quickly and may differ by package or packing option. Provide the production quantity and delivery schedule so the supplier can return a meaningful availability and lead-time response.

এর জন্য ইঞ্জিনিয়ারিং রেফারেন্স ডেটা ATTINY1634-MN — তুলনা, ডিজাইন গাইডেন্স এবং কমপ্লায়েন্স তথ্য।

নির্বাচন গাইড

Choose the ATTINY1634-MN when the design needs a compact, low-power AVR controller with 16 KB Flash, 1 KB SRAM, 18 I/O lines and multiple serial interfaces in a 4 x 4 mm 20-QFN exposed-pad package. Its 1.8 V to 5.5 V range is particularly useful for systems that must operate across low-voltage and conventional supply levels. The two USARTs, USI and I2C slave support make it appropriate for sensor nodes, serial gateways, instrumentation and compact actuator controllers. ATTINY1634-15XZ may be considered only after its exact ordering configuration, package details and device parameters are checked against the manufacturer documentation; the cross-reference result does not by itself prove drop-in equivalence. If firmware depends on the target pin mapping, clock settings, bootloader behavior or interrupt-vector layout, perform a firmware and hardware regression test before substitution. For designs requiring substantially more Flash, SRAM or I/O, move to a larger AVR or another MCU family rather than forcing a pin-compatible replacement.

বিকল্পের সাথে তুলনা

পারামিটার এই পণ্য ATTINY1634-15XZ
Brand Microchip Technology Microchip Technology
Package 20-QFN exposed-pad, 4 x 4 mm 20-QFN exposed-pad, 4 x 4 mm
Core AVR 8-bit AVR 8-bit

মূল পার্থক্যসমূহ

  • Compact communication-rich AVR controller (বনামATTINY1634-15XZ)
  • Broad operating-voltage range (বনামATTINY1634-15XZ)
  • Integrated timing and communication resources (বনামATTINY1634-15XZ)

ডিজাইন নোট

Route the ATTINY1634-MN power and ground pins using the manufacturer recommended land pattern, and connect the 20-QFN exposed pad according to the package guidance. Place the required decoupling capacitors close to their associated supply pins. Keep sensitive analog inputs away from switching nodes and high-current return paths to reduce coupled noise and ground bounce.

Follow the manufacturer clock recommendations when using an external oscillator, and keep the clock path short and physically separated from noisy signals. Confirm programming-test access, reset behavior and debug considerations before fixing the layout. If the I2C or USART traces leave the board, route them away from motor drives and switching-converter power loops.

The 1.8 V to 5.5 V operating range supports flexible rail selection, but the complete design must respect the limits of every attached peripheral and I/O pin. Define valid logic levels for each powered state, especially during startup and partial shutdown. Use the low-power modes only after verifying wake sources, clock-restart timing and the maximum interrupt latency required by the application.

Do not treat a related ATtiny1634 order code as an automatically approved drop-in replacement. Before substitution, compare the exact package drawing, exposed-pad connection, pin names, memory map, clock limits, peripheral multiplexing and interrupt vectors. Firmware that depends on the ATTINY1634-MN pin configuration should also be recompiled and regression-tested against the selected replacement.

কমপ্লায়েন্স তথ্য

RoHS
Compliant
REACH
Unknown
AEC-Q100
Unknown
লিড ফ্রি
Unknown
হ্যালোজেন ফ্রি
Unknown
কনফ্লিক্ট মিনারেলস
Unknown

The Microchip product listing identifies the ATTINY1634-MN as RoHS compliant. No definitive REACH, AEC-Q100, lead-free, halogen-free or conflict-minerals declaration was established for this orderable part.

ডেটা যাচাই করা হয়েছে: 2026-11-19 — ডেটা XAIPART-এর কম্পোনেন্ট ইঞ্জিনিয়ারিং টিম দ্বারা যাচাই ও কিউরেট করা হয়েছে

সম্পর্কিত অনুসন্ধান

attiny1634 datasheet attiny1634 pinout attiny1634 mnr attiny1634 arduino ATTINY1634-MN datasheet pdf ATTINY1634-MN pinout ATTINY1634-MN equivalent ATTINY1634-MN replacement ATTINY1634-MN price ATTINY1634-MN stock Microchip ATTINY1634-MN ATTINY1634 20-QFN application circuit

সম্পর্কিত কম্পোনেন্ট ও শর্তাবলী

Microchip Technology ATTINY1634-MN ATTINY1634 ATTINY1634-15XZ AVR 8-bit microcontroller embedded controller enhanced RISC architecture semiconductor picoPower 16 KB Flash 256 B EEPROM 1 KB SRAM 12 MHz USART Universal Serial Interface I2C slave 20-QFN exposed pad QFN family surface mount SMD low-power CMOS industrial control sensor node serial gateway RoHS
তাৎক্ষণিক বিলওয়াছে রেকোজিউইট
সম্পূর্ণ বিবরণ পূরণ করুন — আমাদের সেলস টিম 24 ঘণ্টার মধ্যে উত্তর দেবে
পার্ট নম্বর উৎপাদক প্যাকেজ QTY লক্ষ্যমূল্য প্রসারিত
✓
বিল প্রস্তুত করা হয়েছে!

আমরা ২৪ ঘণ্টার মধ্যে আপনার ইমেইলে প্রত্যুত্তর দেব

1
RFQ জমা হয়েছে
2
কোটেশন পাওয়া গেছে
3
অর্ডার দেওয়া হয়েছে
4
পেমেন্ট
5
শিপ করা হয়েছে
6
ডেলিভারি হয়েছে
RFQ বিবরণ দেখুন