BTS3050EJXUMA1 - 50mΩ 4A Smart Low-Side Switch | Infineon
MPN: BTS3050EJXUMA1 ✓ সক্রিয়BTS3050EJXUMA1 সারাংশ
A Smart Low-Side Switch (SLS) is a type of power distribution switch — itself a category of power management IC — that switches the negative (ground) side of a load rather than the positive supply. In the power management taxonomy, this places the BTS3050EJXUMA1 as: power distribution switch -> load switch -> smart low-side switch -> power semiconductor. SLS devices are widely used in automotive body electronics where high-side driving is impractical or where ground-side PWM dimming (for example, LED tail lamps) is the desired topology.
Key features include a typical on-state resistance (RDS(on)) of 50 mΩ at 25 °C, integrated over-temperature protection with auto-restart behavior, ESD protection on the IN (Source / Ground) pin, and current-limit foldback under overload. The PG-TDSO-8-31 package provides an exposed tab for thermal dissipation, and the device is qualified for 12 V automotive board-net environments with transient tolerance to typical load-dump events when paired with external TVS protection.
The BTS3050EJXUMA1 is built on Infineon's proven HITFET™ +12V process family, combining a vertical N-channel DMOS output stage with CMOS control logic on the same die. This monolithic integration minimizes propagation delay from IN to OUT and eliminates the need for an external gate drive, allowing the part to be driven directly from a 3.3 V or 5 V microcontroller output. The smart-protection block monitors junction temperature via an on-die sensor and latches/restarts the output autonomously, freeing the host MCU from fault-handling routines.
Typical applications include automotive LED lighting modules (rear lamps, interior illumination), relay and solenoid replacement, small DC motor drivers for HVAC flaps and door mirrors, and general 12 V resistive load switching in body control modules (BCMs). The device is particularly suited to PWM-dimmed lighting because its low-side topology and fast switching allow direct ground-referenced modulation without bootstrap capacitors.
When designing with the BTS3050EJXUMA1, observe the maximum RDS(on) derating at elevated junction temperature and ensure the exposed pad is soldered to a sufficient copper pour to keep Tj below 150 °C under worst-case ambient and load conditions. Decouple the load supply with a local ceramic capacitor close to the device's Vbb pin to absorb load-dump and reverse-battery transients.
এর জন্য ড্রপ-ইন বিকল্প BTS3050EJXUMA1 — একই package, pin-to-pin compatible। ভিন্ন package-এর যেসব পার্টে PCB rework প্রয়োজন সেগুলো বাদ দেওয়া হয়েছে।
এই সিরিজের ভ্যারিয়েন্ট
একই সিরিজের মডেল যেগুলো drop-in compatible BTS3050EJXUMA1 (একই form factor এবং footprint) — পার্থক্য রয়েছে Package, Product Type, Operating Temperature Range, Operating Temperature, Technology.
BTS3050TFATMA1
✅ ড্রপ-ইনমূল্যের জন্য যোগাযোগ করুন
ডেটাশিট দেখুন →BTS3035TFATMA1
✅ ড্রপ-ইনমূল্যের জন্য যোগাযোগ করুন
ডেটাশিট দেখুন →BTS3060TFATMA1
✅ ড্রপ-ইনমূল্যের জন্য যোগাযোগ করুন
ডেটাশিট দেখুন →BTS3125TFATMA1
✅ ড্রপ-ইনমূল্যের জন্য যোগাযোগ করুন
ডেটাশিট দেখুন →BTS118DATMA1
✅ ড্রপ-ইনমূল্যের জন্য যোগাযোগ করুন
ডেটাশিট দেখুন →BTS3050EJXUMA1 সর্বোচ্চ রেটিং ও বৈদ্যুতিক বৈশিষ্ট্য
| Product Type | Smart Low-Side Power Switch |
| Technology | N-Channel Vertical Power MOSFET (HITFET +12V) |
| On-State Resistance (RDS(on)) | 50 mΩ (typical at 25 °C) |
| Continuous Load Current | 4 A |
| Number of Channels | 1 (Single channel) |
| টপোলজি | Low-Side Switch (1:1) |
| Load Voltage | 12 V automotive nominal |
| ESD Protection | Yes (on IN pin / Source / Ground) |
| Thermal Protection | Auto-restart overtemperature shutdown |
| প্যাকেজ | PG-TDSO-8-31 (TDSO8-31) |
| মাউন্টিং টাইপ | Surface Mount |
| RoHS স্ট্যাটাস | Compliant |
| Automotive Grade | AEC-Q100 qualified (HITFET +12V family) |
BTS3050EJXUMA1 পিন কনফিগারেশন
| পিন 1 | IN — Logic input (drive from MCU GPIO; also ESD-protected Source/Ground reference) |
| পিন 2 | OUT — Power output to load (drain of internal N-channel MOSFET) |
| পিন 3 | OUT — Power output to load (drain; tied to pin 2 internally) |
| পিন 4 | GND — Ground / Source of internal MOSFET |
| পিন 5 | GND — Ground / Source (tied to pin 4) |
| পিন 6 | GND — Ground / Source (tied to pin 4) |
| পিন 7 | Vbb — Load supply voltage (battery / 12 V rail) |
| পিন 8 | NC — Not connected (per datasheet) |
নিরাপদ অপারেটিং এলাকা
সাধারণ ব্যবহার
BTS3050EJXUMA1 এর জন্য উপযুক্ত 6 অ্যাপ্লিকেশনs: Automotive LED Tail Lamp PWM Driver, Body Control Module (BCM) Load Driver, Relay and Solenoid Replacement, HVAC Flap and Door Mirror Motor Driver, Resistive Heating Element Switch, General-Purpose 12 V Industrial Load Switch.
Automotive LED Tail Lamp PWM Driver
The BTS3050EJXUMA1 is well-suited to 12 V automotive LED tail lamp modules because its low-side N-channel MOSFET switches the ground return, allowing direct ground-referenced PWM dimming without bootstrap capacitors. With 50 mΩ RDS(on) and 4 A continuous current, it comfortably drives multi-LED strings drawing 1-2 A; for example, a 1.5 A string dissipates only ~113 mW in the switch. Integrated thermal auto-restart protects against LED short-to-ground faults, and the small PG-TDSO-8-31 footprint suits compact lamp PCBs. Companion: BTS3035TFATMA1 for higher-current lamp variants.
সুপারিশকৃত
Body Control Module (BCM) Load Driver
In 12 V body control modules the BTS3050EJXUMA1 serves as the protected interface between a 3.3 V/5 V microcontroller GPIO and ground-referenced loads such as interior lamps, mirror heaters, or indicator LEDs. The integrated ESD protection on the IN pin simplifies ISO 7637-2 transient design, while the 50 mΩ RDS(on) limits conduction loss to under 200 mW at typical BCM load currents of 1-2 A. The PG-TDSO-8-31 package enables high-density multi-channel BCM layouts. Companion: TLE75080ESHXUMA1 multi-channel SPI driver.
সুপারিশকৃত
Relay and Solenoid Replacement
The BTS3050EJXUMA1 is a solid-state replacement for automotive relays and small solenoids, eliminating coil current draw, contact bounce, and mechanical wear. Its 4 A continuous rating covers most body-electronic relays driving resistive or inductive loads up to ~50 W at 13.5 V, and the smart-protection features handle the inrush and back-EMF of inductive kick. Mounted in PG-TDSO-8-31, it sits directly on the PCB without a socket. Companion: BTN9960LVAUMA1 for half-bridge motor control.
সুপারিশকৃত
HVAC Flap and Door Mirror Motor Driver
Small brushed DC motors in HVAC air-flap actuators and door mirror adjustment mechanisms operate from the BTS3050EJXUMA1's low-side switch in either single-direction or back-to-back H-bridge configurations. The 50 mΩ RDS(on) keeps conduction loss below ~500 mW at typical 3 A motor currents, and the integrated thermal auto-restart prevents damage during stalled-rotor conditions. PWM speed control up to several kHz is supported by the fast switching of the N-channel output stage. Companion: BTS5210GXUMA1 dual high-side for mirror fold.
সুপারিশকৃত
Resistive Heating Element Switch
For 12 V resistive heating elements such as seat heaters, mirror heaters, or steering-wheel heaters, the BTS3050EJXUMA1 offers a protected low-side switch with thermal auto-restart that protects against over-current faults and shorts. Its 4 A rating supports up to ~50 W of heating power at 13.5 V system voltage, sufficient for typical single-zone seat heaters. The 50 mΩ RDS(on) limits conduction loss to under 1 W at full load. Companion: TLE75004EPDXUMA1 multi-channel low-side for seat control.
সুপারিশকৃত
General-Purpose 12 V Industrial Load Switch
Outside automotive, the BTS3050EJXUMA1 serves as a protected low-side switch for 12 V industrial control systems, including PLC digital outputs, process control valves, and indicator lamps. Its integrated ESD protection, current limit, and thermal shutdown reduce external protection component count, while the 50 mΩ / 4 A rating covers most low-power industrial loads. The PG-TDSO-8-31 package is suitable for SMT manufacturing. Companion: IRS2181STRPBF for half-bridge industrial motor control.
সুপারিশকৃত
সুপারিশকৃত পণ্যের সারসংক্ষেপ
এর জন্য ইঞ্জিনিয়ারিং রেফারেন্স ডেটা BTS3050EJXUMA1 — তুলনা, ডিজাইন গাইডেন্স এবং কমপ্লায়েন্স তথ্য।
নির্বাচন গাইড
বিকল্পের সাথে তুলনা
| পারামিটার | এই পণ্য | BTS3050TFATMA1 | BTS3035TFATMA1 | BTS3060TFATMA1 | BTS3125TFATMA1 | BTS118DATMA1 |
|---|---|---|---|---|---|---|
| Brand | Infineon Technologies | Infineon Technologies | Infineon Technologies | Infineon Technologies | Infineon Technologies | Infineon Technologies |
| Package | PG-TDSO-8-31 | TO-252 (DPAK) | TO-252 (DPAK) | TO-252 (DPAK) | TO-252 (DPAK) | TO-252 (DPAK) |
| Topology | Low-Side (1:1) | Low-Side (1:1) | Low-Side (1:1) | Low-Side (1:1) | Low-Side (1:1) | Low-Side (1:1) |
| Technology | HITFET +12V (N-channel vertical MOSFET) | HITFET +12V (same) | HITFET +12V (same) | HITFET +12V (same) | HITFET +12V (same) | HITFET +12V (same) |
| Thermal Protection | Auto-restart shutdown | Auto-restart shutdown | Auto-restart shutdown | Auto-restart shutdown | Auto-restart shutdown | Auto-restart shutdown |
| Automotive Grade | AEC-Q100 (family) | AEC-Q100 (family) | AEC-Q100 (family) | AEC-Q100 (family) | AEC-Q100 (family) | AEC-Q100 (family) |
মূল পার্থক্যসমূহ
- Compact PG-TDSO-8-31 footprint (বনামBTS3050TFATMA1)
- Lower RDS(on) than higher-current siblings (বনামBTS3060TFATMA1)
- Drop-in replacement within HITFET +12V family (বনামBTS3125TFATMA1)
ডিজাইন নোট
At 4 A continuous load in PG-TDSO-8-31, the BTS3050EJXUMA1 dissipates roughly P = I² × R = 16 × 0.05 = 0.8 W. Estimated: with a typical theta_JA of ~50 C/W on a 1 square inch copper pour, junction temperature rise above ambient is ~40 C. Above ~3 A sustained, increase copper area or add thermal vias to the exposed tab to keep Tj below the 150 °C thermal-shutdown threshold. Always design for worst-case ambient (e.g. 85 °C in engine compartment).
Solder the package exposed tab (Source/Ground) to a continuous copper pour of at least 1 square inch on the top layer; add thermal vias to inner/bottom copper layers for higher current. Place the local Vbb decoupling ceramic capacitor (≥100 nF X7R) within 5 mm of pin 7 to absorb load-dump transients. Keep the IN trace short and away from switching nodes to minimize injected noise.
Do not connect a load to Vbb without a return path through the BTS3050EJXUMA1's GND pins — this is a low-side switch, not a high-side driver. Avoid driving the IN pin above the absolute-max rating; ESD protection is integrated but does not replace external TVS for ISO 7637-2 pulse A. Verify that PWM frequency stays within the part's switching capability; for very high frequencies consult the datasheet's switching-time curves.
কমপ্লায়েন্স তথ্য
RoHS and REACH compliant per Infineon product page. HITFET +12V family is AEC-Q100 qualified for automotive use. Halogen-free and lead-free per Infineon packaging materials declaration.
