CD4029BD - 11MHz Up/Down Counter | Texas Instruments
MPN: CD4029BD ✓ সক্রিয়CD4029BD সারাংশ
A CMOS up/down counter is a digital logic IC that increments or decrements a binary count in response to clock transitions and control signals. The CD4029BD family belongs to the CD4000 CMOS logic hierarchy, combining counter, divider, and control functions in a single integrated circuit. Unlike a general-purpose microcontroller, it provides dedicated counting hardware that can operate deterministically with limited external logic, making it useful in timing, event-counting, and industrial control applications.
The counter supports binary or decade counting configurations, allowing it to be adapted to different numerical bases and counting sequences. Its rising-edge triggering means the count changes on the active clock transition rather than throughout the high or low interval. The 11 MHz operating point supports relatively fast counting for a classic CMOS logic device, while the broad 3 V to 18 V supply range allows operation across multiple supply environments.
The CDIP-16 package is a through-hole format intended for insertion into printed circuit board sockets or plated holes. Its lead arrangement follows the 16-pin dual in-line package format, with two rows of eight leads on a 0.300-inch pitch. Ceramic-sealed CDIP construction can also support applications requiring environmental protection and stable operation over a broad temperature range.
Typical uses include industrial event counters, programmable timers, frequency division, test-equipment sequencing, digital control loops, and embedded counters that supplement a host microcontroller. Designers should confirm clock edge behavior, mode controls, and output states against the manufacturer pin description and truth table before committing a PCB layout.
The principal design considerations are supply decoupling, clock-signal integrity, and correct handling of asynchronous control inputs. A low-impedance bypass capacitor should be placed close to the power pins, while the clock trace should remain short and avoid crossing noisy switching nodes. The counter should also be initialized to a known state if the system depends on a defined count after power-up.
This product summary combines the manufacturer product description with package, operating-range, and clock-frequency information and adds practical guidance for selecting and implementing the CD4029BD in count-and-control systems.
এর জন্য ড্রপ-ইন বিকল্প CD4029BD — একই package, pin-to-pin compatible। ভিন্ন package-এর যেসব পার্টে PCB rework প্রয়োজন সেগুলো বাদ দেওয়া হয়েছে।
এই পণ্যের জন্য কোনো ড্রপ-ইন বিকল্প পাওয়া যায়নি।
বিকল্প অনুরোধ করুনCD4029BD সর্বোচ্চ রেটিং ও বৈদ্যুতিক বৈশিষ্ট্য
| Product Type | Presettable binary/decade up/down counter |
| Logic Family | CD4000 CMOS series |
| Supply Voltage Range | 3 V to 18 V |
| সর্বোচ্চ ক্লক ফ্রিকোয়েন্সি | 11 MHz |
| Clock Triggering | Rising edge |
| Counting Modes | Binary and decade up/down counting |
| Presettable Count | User-programmable count state |
| Number of Counter Elements | 1 counter element |
| Package Type | CDIP-16 |
| পিন সংখ্যা | 16 pins |
| Package Lead Span | 0.300 inch (7.62 mm) |
| মাউন্টিং স্টাইল | Through-hole |
| Technology | CMOS |
CD4029BD 0.300 inch (7.62 mm) পিন কনফিগারেশন গাইড
CD4029BD (0.300 inch (7.62 mm) প্যাকেজ)-এর পিন কনফিগারেশন। এই ডিজিটাল IC-তে GPIO, কমিউনিকেশন ইন্টারফেস (UART, SPI, I2C) এবং পাওয়ার পিন রয়েছে। বিকল্প পিন ফাংশন ও কনফিগারেশন অপশনের জন্য প্রস্তুতকারকের ডেটাশিট দেখুন। এমবেডেড সিস্টেম ডিজাইন ও PCB লেআউটের জন্য অপরিহার্য।
এর জন্য বিস্তারিত পিনআউট ডেটা পাওয়া যায়নি CD4029BD.
দেখুন ডেটাশিট সম্পূর্ণ পিন কনফিগারেশনের জন্য।
সাধারণ ব্যবহার
CD4029BD এর জন্য উপযুক্ত 6 অ্যাপ্লিকেশনs: Industrial Event Counting, Programmable Timing Control, Frequency Division, Digital Test Equipment Sequencing, Stepper Motor Pulse Positioning, Automated Sorting and Batch Control.
Industrial Event Counting
The CD4029BD fits fixed industrial counting tasks where sensors generate clean pulses and the controller must count upward, downward, or from a preset state. Its rising-edge counting behavior and 11 MHz maximum clock frequency provide ample timing margin for many pulse-counting systems operating below the device limit. The 3 V to 18 V supply range also permits integration with multiple CMOS logic levels. Engineers should condition noisy sensor outputs, use Schmitt-triggered stages where required, and ensure the maximum operating temperature meets the enclosure environment. The dedicated counter is especially useful when a microcontroller is unnecessary and the control sequence is fixed.
সুপারিশকৃত
Programmable Timing Control
The CD4029BD can form the counting element of a programmable timer because its preset capability allows the counter to begin from a defined value and advance toward a terminal count. This approach is useful for machine timing, delayed actuation, and process sequencing where the timing interval is defined by the initial preset and clock frequency. The 11 MHz operating limit supports fast timing resolution, although the actual minimum interval must also satisfy the counter's logic and output propagation requirements. External gating and output decoding determine how the terminal state produces the final timing action.
সুপারিশকৃত
Frequency Division
The CD4029BD is appropriate for frequency division when a clock must be reduced to a lower-rate enable pulse for sequencing or control. Its binary counting capability allows selected output states to create division ratios, while decade operation provides convenient ten-based stepping. For clean results, the source clock should have controlled rise and fall times, and the divider outputs should not be overdriven. The part's 11 MHz maximum input frequency offers useful margin for many low-to-moderate-speed industrial clock systems. Select the proper output tap and include reset or preset behavior in the system timing specification.
সুপারিশকৃত
Digital Test Equipment Sequencing
The CD4029BD can implement repeatable step sequencing in test equipment, panel meters, and diagnostic fixtures that must advance through a series of test states. Preset control lets the equipment load a specific starting count, while up or down operation determines the direction of the sequence. The 16-pin CDIP format supports conventional through-hole prototyping and repair workflows. Engineers should define the legal state transitions, initialize the count after power-up, and synchronize external commands with the clock. The dedicated counter is useful when a fixed hardware sequence is preferable to software-controlled state management.
সুপারিশকৃত
Stepper Motor Pulse Positioning
The CD4029BD can count command or position pulses in a stepper-motor control system, providing a hardware count of movement steps without requiring a microcontroller to execute every counting operation. The rising-edge input works naturally with pulse trains, and the programmable preset can support repeatable travel commands or incremental positioning. Signal-conditioning logic should prevent motor-driver noise from propagating back into the counter. The 3 V to 18 V range facilitates interface design, while the 11 MHz maximum frequency covers many pulse-rate requirements. Position limits and homing behavior must be implemented consistently with the counter's preset and direction controls.
সুপারিশকৃত
Automated Sorting and Batch Control
The CD4029BD supports batch counting in sorting, packaging, and material-handling systems where each accepted item generates a pulse. A preset count establishes the batch size, and the counter output can trigger the actuator or request the next item after the target quantity is reached. Its dedicated hardware operation supports deterministic throughput without continuous processor intervention. Inputs should be debounced and optically isolated when they originate from long cables or noisy machinery. The design must also define behavior for overflow, jam, reset, and premature-stop conditions so that a count comparison does not cause unintended actuation.
সুপারিশকৃত
সুপারিশকৃত পণ্যের সারসংক্ষেপ
এর জন্য ইঞ্জিনিয়ারিং রেফারেন্স ডেটা CD4029BD — তুলনা, ডিজাইন গাইডেন্স এবং কমপ্লায়েন্স তথ্য।
নির্বাচন গাইড
বিকল্পের সাথে তুলনা
| পারামিটার | এই পণ্য |
|---|---|
| Package | CDIP-16 |
| Brand | Texas Instruments |
| Product Type | Presettable binary/decade up/down counter |
| Supply Voltage Range | 3 V to 18 V |
| Maximum Clock Frequency | 11 MHz |
| Clock Triggering | Rising edge |
| Logic Technology | CMOS |
| Counting Direction | Up/down |
| Counting Base | Binary and decade |
| Mounting Style | Through-hole |
মূল পার্থক্যসমূহ
- Dedicated preset up/down counting in a single CMOS IC (বনামCD4060BK)
- Rising-edge counting with a stated 11 MHz maximum frequency (বনামCD4020BK)
- Broad 3 V to 18 V CMOS operating range (বনামMicrocontroller-based counter)
ডিজাইন নোট
Place the manufacturer-recommended bypass capacitor immediately adjacent to the supply and ground pins, and route each connection with minimum loop area. A compact supply path helps suppress switching disturbances that could couple into the clock or control inputs. Because the CD4029BD supports a 3 V to 18 V supply range, verify that the capacitor voltage rating, logic-level thresholds, and attached interface devices are suitable for the selected operating voltage.
Keep the clock trace short and provide a clean rising edge at the counter input. Avoid routing it parallel to high-current switching traces, isolate it from motor-driver outputs, and use a gate or conditioning stage when the source has slow edges or excessive noise. Remember that the CD4029BD advances on the rising edge, so input polarity and transition timing must agree with the external pulse-generating circuit.
Design the 16-pin CDIP footprint for a 0.300-inch, or 7.62 mm, lead span and follow the manufacturer's package drawing for hole diameter and row spacing. Keep digital counter traces away from analog inputs, relay contacts, and power-converter switches. Define reset and preset states in the circuit so that power-up does not leave the counter operating from an unintended count value.
Do not substitute another CD4029 suffix solely because the base family name matches. Package construction, temperature rating, qualification, and ordering suffix can change between otherwise related devices. Confirm the pin-description table, operating truth table, and mechanical drawing before approving a replacement. Also avoid treating the maximum clock frequency as a guarantee at every supply voltage; use the manufacturer operating conditions for the actual electrical environment.
কমপ্লায়েন্স তথ্য
No explicit compliance statements for the exact CD4029BD ordering variant are included in the manufacturer product information. AEC-Q100 is treated as not applicable because the product is a general-purpose logic IC rather than an automotive-qualified device.
