CY8C3246LTI-121 - 50MHz 64KB 8-Bit MCU | Infineon
MPN: CY8C3246LTI-121 ✓ সক্রিয়CY8C3246LTI-121 সারাংশ
A programmable system-on-chip, or PSoC, combines a microcontroller core with configurable analog and digital blocks. The PSoC 3 CY8C32 family belongs to the broader hierarchy of embedded microcontroller, embedded processor, and semiconductor devices. Rather than relying only on fixed hardware peripherals, a PSoC implementation can route signals through programmable digital blocks and analog resources to create application-specific functions while reducing external component count.
The CY8C3246LTI-121 provides 64 KB, or 64K by 8 bits, of flash memory, an 8-bit architecture, and a maximum clock frequency of 50 MHz. Its operating voltage range extends from 1.71 V to 5.5 V. The device also includes configurable counter, communications, SPI, I2C, and UART-related functionality, supporting designs that connect sensors, actuators, human-interface controls, and external communication devices.
The 48-QFN package supports dense PCB placement while requiring careful ground-plane and thermal-layout practices. Because this is a mixed-signal microcontroller, analog-capable designs should keep sensitive inputs away from high-current switching paths and provide clean return paths for reference and supply connections. Programmable analog and digital blocks also require deliberate clocking, interrupt, and pin-assignment planning during firmware configuration.
Typical uses include compact industrial controllers, sensor-hub nodes, touch and keypad interfaces, communication bridges, motor-control supervisory systems, and embedded consumer products. The 50 MHz operating speed supports responsive control tasks, while 64 KB of flash provides room for application firmware, configuration data, and boot logic. Its broad 1.71 V to 5.5 V supply range can simplify support for multiple embedded supply rails when the complete board architecture remains compatible with the device limits.
A critical design consideration is that firmware configuration becomes part of the device's hardware behavior. Engineers should finalize the clock tree, GPIO assignments, analog blocks, interrupts, and serial interfaces before PCB release, then validate the configured design with representative signal rates and environmental conditions. The 48-QFN footprint also requires a land pattern that follows the manufacturer package drawing and exposes adequate thermal and electrical grounding.
This product page organizes the 50 MHz clock rate, 64 KB flash capacity, 1.71 V to 5.5 V supply range, 48-QFN package, peripheral capabilities, application guidance, and replacement considerations to support faster engineering selection and board-level planning.
এর জন্য ড্রপ-ইন বিকল্প CY8C3246LTI-121 — একই package, pin-to-pin compatible। ভিন্ন package-এর যেসব পার্টে PCB rework প্রয়োজন সেগুলো বাদ দেওয়া হয়েছে।
CY8C3246LTI-128
✅ ড্রপ-ইন📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)
CY8C3246LTI-121 সর্বোচ্চ রেটিং ও বৈদ্যুতিক বৈশিষ্ট্য
| Product Type | 8-bit programmable system-on-chip microcontroller |
| Product Family | PSoC 3 CY8C32xx |
| CPU Architecture | 8051-compatible 8-bit core |
| সর্বোচ্চ ক্লক ফ্রিকোয়েন্সি | 50 MHz |
| Flash Memory | 64 KB (64K x 8 bits) |
| Operating Voltage Range | 1.71 V to 5.5 V |
| প্যাকেজ | 48-QFN (7 mm x 7 mm) |
| মাউন্টিং টাইপ | Surface mount |
| Configurable Counters | 5 counters |
| Serial Interface Support | SPI, I2C, and UART |
| SPI Configuration | Master and slave |
CY8C3246LTI-121 48-qfn (7 mm x 7 mm) পিন কনফিগারেশন গাইড
CY8C3246LTI-121 (48-qfn (7 mm x 7 mm) প্যাকেজ)-এর পিন কনফিগারেশন। এই ডিজিটাল IC-তে GPIO, কমিউনিকেশন ইন্টারফেস (UART, SPI, I2C) এবং পাওয়ার পিন রয়েছে। বিকল্প পিন ফাংশন ও কনফিগারেশন অপশনের জন্য প্রস্তুতকারকের ডেটাশিট দেখুন। এমবেডেড সিস্টেম ডিজাইন ও PCB লেআউটের জন্য অপরিহার্য।
এর জন্য বিস্তারিত পিনআউট ডেটা পাওয়া যায়নি CY8C3246LTI-121.
দেখুন ডেটাশিট সম্পূর্ণ পিন কনফিগারেশনের জন্য।
সাধারণ ব্যবহার
CY8C3246LTI-121 এর জন্য উপযুক্ত 6 অ্যাপ্লিকেশনs: Industrial Sensor Hub, UART Communication Bridge, Human Interface Controller, Compact Motor Control Supervisor, Connected Consumer Controller, Data Acquisition Front End.
Industrial Sensor Hub
The CY8C3246LTI-121 fits compact industrial sensor-hub designs that combine multiple sensing channels with local control and serial communications. Its 50 MHz 8051-compatible core supports responsive acquisition and signal-processing tasks, while 64 KB of flash provides room for application firmware, configuration tables, and diagnostic routines. The device's configurable counters and communications blocks can organize timing and data-transfer functions without requiring a separate peripheral controller. A system operating from a 3.3 V rail can remain within the documented 1.71 V to 5.5 V range. The main design constraint is that PCB assignments and the clock configuration should be finalized before layout because PSoC resources and board-level signal integrity influence which pins and peripheral blocks can be used together.
সুপারিশকৃত
UART Communication Bridge
The CY8C3246LTI-121 is well suited to a compact protocol-conversion or communications bridge because it combines an 8051-compatible core with UART, I2C, and SPI interfaces. At up to 50 MHz, the processor can service multiple serial tasks and implement framing, buffering, address translation, or device discovery. The 64 KB flash capacity is useful for fixed protocol tables and application firmware, while the 1.71 V to 5.5 V operating range supports low-voltage embedded designs. Engineers should calculate baud-rate tolerance and buffer requirements for the worst-case traffic load, and place serial routing away from high-energy analog paths to reduce susceptibility to interference.
সুপারিশকৃত
Human Interface Controller
A keypad, rotary encoder, and status-indicator design can use the CY8C3246LTI-121 as a compact human-interface controller. Its configurable counters and digital resources can support debouncing, event counting, display sequencing, and programmable I/O behavior, while the 50 MHz CPU leaves performance headroom for a responsive user interface. The 48-QFN package is useful when the board area around buttons, LEDs, and an optional display is constrained. Firmware must assign pins consistently with the PSoC configuration, and the layout should keep long user-interface traces away from motors, relays, and switching-power connections to minimize false event detection.
সুপারিশকৃত
Compact Motor Control Supervisor
The CY8C3246LTI-121 can serve as the supervisory controller in a compact motor or actuator system. Its 50 MHz processing capability supports state-machine execution, fault logging, timing functions, and communications with a higher-level controller, while five configurable counters provide resources for timing-intensive tasks. The 64 KB flash region accommodates control code, motion parameters, and diagnostic information. This role is best suited to supervisory functions rather than directly driving a high-current motor stage. Designers should separate power switching from sensitive control traces, use defined shutdown behavior for fault conditions, and confirm that the final board maintains the device within its documented 1.71 V to 5.5 V supply range.
সুপারিশকৃত
Connected Consumer Controller
The CY8C3246LTI-121 can serve as the local controller in a compact connected consumer product that combines capacitive or digital sensing with serial accessories. Its PSoC architecture allows signal routing and peripheral behavior to be configured in firmware, while the 8051-compatible 50 MHz core handles control logic and interface tasks. The 64 KB flash capacity is appropriate for production firmware, calibration values, and communication protocols. For a battery-powered product, the low end of the 1.71 V to 5.5 V operating range is useful, but power measurements must include the configured peripheral blocks and I/O activity. The 48-QFN land pattern should be reviewed carefully because its 7 mm by 7 mm body leaves limited clearance around fine-pitch leads.
সুপারিশকৃত
Data Acquisition Front End
The CY8C3246LTI-121 is applicable to a mixed-signal data-acquisition front end where an 8-bit control processor must coordinate sensors and transfer results over I2C, SPI, or UART. Its PSoC resources permit configurable signal paths and counters to be integrated with the CPU, reducing the need for separate logic when the signal set is well understood. The 50 MHz clock supports control-loop and buffering tasks, and 64 KB flash can hold acquisition firmware and calibration data. Signal-chain performance depends on careful PCB partitioning: analog inputs should be short, reference and supply paths should be quiet, and digital communication lines should not share noisy return paths with sensitive measurements.
সুপারিশকৃত
সুপারিশকৃত পণ্যের সারসংক্ষেপ
এর জন্য ইঞ্জিনিয়ারিং রেফারেন্স ডেটা CY8C3246LTI-121 — তুলনা, ডিজাইন গাইডেন্স এবং কমপ্লায়েন্স তথ্য।
নির্বাচন গাইড
বিকল্পের সাথে তুলনা
| পারামিটার | এই পণ্য | CY8C3246LTI-128 |
|---|---|---|
| Brand | Infineon Technologies | Infineon Technologies |
| Package | 48-QFN (7 mm x 7 mm) | 48-QFN (7 mm x 7 mm) |
| Product Type | 8-bit PSoC 3 CY8C32xx microcontroller | PSoC 3 CY8C32 family microcontroller |
| CPU Architecture | 8051-compatible 8-bit core | 8051 CPU |
| Flash Memory | 64 KB | 64 KB |
মূল পার্থক্যসমূহ
- Defined 50 MHz operating point (বনামCY8C3246LTI-128)
- 64 KB flash configuration (বনামCY8C3246LTI-128)
- Documented compact package (বনামCY8C3246LTI-128)
- Broad serial-interface integration (বনামCY8C3246LTI-128)
ডিজাইন নোট
Use the manufacturer package drawing for the 48-QFN land pattern and verify pin 1 orientation against the PCB footprint. Place input, output, and decoupling connections directly beneath the relevant package terminals where practical. Because the 7 mm by 7 mm QFN has closely spaced leads, a short return path and uninterrupted ground plane are especially important for clean communication among the configurable analog, digital, and timing resources.
Finalize the PSoC clock, GPIO, analog-routing, and serial-interface configuration before PCB routing because configured blocks can restrict pin assignments. Keep sensitive analog and reference signals away from switching nodes and high-current return paths. If an SPI or UART interface crosses a noisy board region, inspect return-path continuity and add source-series damping only after signal-integrity measurements identify a need.
Do not treat another CY8C3246LTI ordering suffix as interchangeable solely because it has the same family name. Compare the ordering tables for CPU speed, temperature grade, flash configuration, pin functions, and package marking. Also verify the programmed PSoC configuration is compatible with the physical pins and peripheral routing used on the PCB before releasing firmware for production.
কমপ্লায়েন্স তথ্য
Compliance status was not identified in the manufacturer datasheet listing or distributor technical snippets.