Renesas Electronics

ISL8488IBZ - 5V Full-Duplex RS-485/RS-422 Transceiver | Renesas

MPN: ISL8488IBZ ✓ সক্রিয়
5 V Vdss RS-485 and RS-422 Rds(on) 8-pin SOIC Package
সর্বনিম্ন অর্ডার পরিমাণ: 1 |

ISL8488IBZ সারাংশ

Renesas ISL8488IBZ is a 5V, low-power, full-duplex RS-485/RS-422 interface transceiver packaged in an 8-pin SOIC. It supports a 4.5V to 5.5V supply range, combines one driver and one receiver in each package, and is identified by the source material as an ESD-protected BiCMOS communications device. The ISL8488IBZ family is specified for both RS-485 and RS-422 balanced communication standards, making it suitable for industrial equipment, data acquisition systems, and point-to-point serial links.

A transceiver such as the ISL8488IBZ belongs to the interface-IC hierarchy: transceiver → driver/receiver → differential data interface → semiconductor. RS-485 supports balanced, multipoint buses that can tolerate common-mode noise better than single-ended logic links, while RS-422 provides a balanced point-to-point interface. The ISL8488IBZ can therefore serve as the physical-layer endpoint in equipment that must exchange data reliably over cables or board-level interconnects.

The key device attributes are its 5V operation, 4.5V to 5.5V tolerance, full-duplex configuration, 1/1 driver-to-receiver arrangement, 8-SOIC package, low-power BiCMOS implementation, and integrated ESD protection. The family literature identifies applications for high-speed or slew-rate-limited communication. A comparison entry lists a 250kbps operating-rate variant in an 8-pin SOIC, making that data point relevant when matching the correct suffix, but it should not be assumed to describe every device in the family without checking the manufacturer ordering guide.

BiCMOS construction combines bipolar and CMOS circuit characteristics to support low-power operation with suitable communications-interface performance. In an RS-485 design, the driver converts a logic-level signal into a differential pair, and the receiver detects the voltage difference between the pair. Full duplex separates the transmit and receive paths so the device can communicate in both directions simultaneously, unlike a half-duplex implementation that must share bus drivers and control signal direction.

Typical uses include industrial process-control links, factory automation equipment, test and measurement instruments, point-to-point RS-422 links, and RS-485 communications nodes. The full-duplex arrangement is particularly useful when each equipment enclosure needs an independent communication channel rather than a shared half-duplex bus. The 8-pin SOIC package also makes the device practical for conventional surface-mount PCB assembly.

PCB design should preserve the differential signal topology, keep the driver and receiver ground connections compact, and route the balanced pair away from switching nodes. External termination and biasing must follow the selected RS-485 or RS-422 network topology. The 4.5V to 5.5V supply range also requires decoupling close to the device so transient current and supply noise do not degrade signal integrity.

This product page combines device identification, electrical constraints, interface selection guidance, strict same-package replacement information, and application-specific design guidance. It also distinguishes the ISL8488IBZ from related suffix variants and highlights which parameters require verification in the manufacturer datasheet before production release.

এর জন্য ড্রপ-ইন বিকল্প ISL8488IBZ — একই package, pin-to-pin compatible। ভিন্ন package-এর যেসব পার্টে PCB rework প্রয়োজন সেগুলো বাদ দেওয়া হয়েছে।

এই সিরিজের ভ্যারিয়েন্ট

একই সিরিজের মডেল যেগুলো drop-in compatible ISL8488IBZ (একই form factor এবং footprint) — পার্থক্য রয়েছে Package, Transceiver Configuration.

Renesas Electronics
Package: 8-SOIC
Transceiver Configuration: 1 transmitter and 1 receiver
এর সাথে তুলনা করুন ISL8488IBZ →

ISL8488IBZ-T

✅ ড্রপ-ইন
📦 8-pin SOIC
Same 5V, 1/1 full-duplex RS-485/RS-422 functions and 8-SOIC footprint; suffix distinguishes the ordering or packing configuration.

📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)

ISL8488EIBZA

✅ ড্রপ-ইন
📦 8-pin SOIC
The documented comparison lists a 4.5V, 250kbps 8-pin configuration; exact suffix-specific ratings must be matched before substitution.

📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)

SP3081EEN-L

✅ ড্রপ-ইন
📦 8-pin SOIC
The documented comparison lists a 4.5V, 250kbps 8-pin complete replacement; verify exact data rate and pin-level behavior.

📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)

ISL8488IBZ বিশেষণ

সাপ্লাই ভোল্টেজ 5 V
Operating Supply Voltage Range 4.5 V to 5.5 V
Supply Tolerance 10%
Interface Standards RS-485 and RS-422
Transceiver Configuration 1 driver / 1 receiver
Duplex Mode Full duplex
Logic Family BiCMOS
Power Class Low power
ESD Protection Yes
Signaling Mode Balanced differential
প্যাকেজ 8-pin SOIC
মাউন্টিং টাইপ Surface mount

ISL8488IBZ 8-pin soic পিন কনফিগারেশন গাইড

ISL8488IBZ (8-pin soic প্যাকেজ)-এর পিন কনফিগারেশন। পিন নম্বরিং, ফাংশন এবং সংযোগ ডায়াগ্রাম প্রস্তুতকারকের ডেটাশিটে সংজ্ঞায়িত করা আছে। সঠিক ফুটপ্রিন্ট এবং সোল্ডারিং নির্দেশিকার জন্য এটি দেখুন।

ISL8488IBZ-এর জন্য 8-pin soic প্যাকেজ পিনআউট ডায়াগ্রাম

এর জন্য বিস্তারিত পিনআউট ডেটা পাওয়া যায়নি ISL8488IBZ.

দেখুন ডেটাশিট সম্পূর্ণ পিন কনফিগারেশনের জন্য।

সাধারণ ব্যবহার

ISL8488IBZ এর জন্য উপযুক্ত 6 অ্যাপ্লিকেশনs: Industrial Process-Control Links, Point-to-Point RS-422 Equipment, RS-485 Communications Nodes, Test and Measurement Instruments, Factory Automation Data Acquisition, Data Acquisition and Control Cabinets.

🏭

Industrial Process-Control Links

The ISL8488IBZ suits industrial process-control equipment that communicates over a 5V RS-485 or RS-422 balanced link. Its full-duplex 1/1 transceiver arrangement allows independent transmit and receive paths, avoiding half-duplex direction-control circuitry at each endpoint. Operation across a 4.5V to 5.5V supply range supports regulated 5V industrial rails, while integrated ESD protection adds a useful layer of protection for board-level connections. In a controller or sensor interface, the device converts between logic signals and the balanced cable interface. Keep the differential pair tightly coupled, provide local supply decoupling, and apply the termination and biasing arrangement appropriate to the selected RS-485 topology.

🔧

Point-to-Point RS-422 Equipment

The ISL8488IBZ is appropriate for point-to-point RS-422 links between two independently clocked pieces of equipment. Its full-duplex configuration provides separate balanced channels for transmission and reception, avoiding shared bus contention and simplifying protocol handling. The device operates from a nominal 5V supply with a documented range of 4.5V to 5.5V, which fits many controller and test-instrument architectures. Designers should use matched differential routing for each pair, maintain a continuous reference plane, and determine receiver and driver termination from the cable length and topology. The manufacturer application circuit should guide protection and bias components before the board is released.

🌐

RS-485 Communications Nodes

The ISL8488IBZ can serve as a communications endpoint in an RS-485 system requiring a full-duplex implementation. Its one-driver, one-receiver arrangement supports simultaneous communication over separate differential paths while the low-power BiCMOS circuitry suits compact 5V equipment. The documented 4.5V to 5.5V operating range provides useful supply tolerance around a nominal 5V rail. At the PCB level, preserve symmetric routing between each differential pair, connect the transceiver ground close to the interface circuitry, and use the datasheet application diagram for termination and protection. Ensure the external network configuration does not impose an incompatible bias or termination scheme on the full-duplex topology.

📡

Test and Measurement Instruments

The ISL8488IBZ fits test and measurement instruments that exchange commands and results over RS-485 or RS-422. A full-duplex interface allows the instrument to transmit measurements and receive configuration commands concurrently, which is useful for automated test systems. The 5V BiCMOS device is compatible with a 4.5V to 5.5V supply environment, and its 8-pin SOIC package supports compact surface-mount layouts. To preserve data integrity, route driver outputs as a short differential pair, provide a solid ground reference, and keep switching regulators and high-speed digital clocks away from the communication traces. Use the manufacturer circuit for supply decoupling and external protection.

🧩

Factory Automation Data Acquisition

The ISL8488IBZ supports factory automation data-acquisition modules that must move sensor and control information reliably over balanced cables. Its integrated ESD protection is useful in industrial environments, while the full-duplex 1/1 architecture avoids sharing the transmitter between receive and send phases. The 4.5V to 5.5V supply range is suitable for common 5V controller rails, although harsher industrial requirements may need additional surge and isolation protection. Keep the transceiver close to the connector, use controlled-impedance differential routing where practical, and provide local bypass capacitance. Select termination and fail-safe bias components according to the exact bus topology.

🖥️

Data Acquisition and Control Cabinets

The ISL8488IBZ can connect remote sensors, actuators, and monitoring modules to a central data-acquisition controller. Balanced RS-485 or RS-422 signaling supports cable-based communication, and the full-duplex arrangement is advantageous when devices must acknowledge commands while continuously reporting measurements. The device's low-power 5V BiCMOS operation, 4.5V to 5.5V input range, and integrated ESD protection align with compact embedded control hardware. In a cabinet design, place the transceiver and protection network near the field connector, maintain symmetric pair geometry, and separate communications routing from power-conversion stages. Verify connector ground continuity and use the manufacturer pin definitions when assigning the 8-SOIC footprint.

সুপারিশকৃত পণ্যের সারসংক্ষেপ

ISL8488EIBZA Same-family 8-SOIC interface alternative ব্যবহৃত হয়: Industrial Process-Control Links, Point-to-Point RS-422 Equipment, Test and Measurement Instruments, Factory Automation Data Acquisition SP3081EEN-L Documented same-package transceiver candidate ব্যবহৃত হয়: Industrial Process-Control Links, RS-485 Communications Nodes, Test and Measurement Instruments, Data Acquisition and Control Cabinets ISL8488IBZ-T Same-family full-duplex 8-SOIC alternative ব্যবহৃত হয়: Point-to-Point RS-422 Equipment, RS-485 Communications Nodes, Factory Automation Data Acquisition, Data Acquisition and Control Cabinets
What is the ISL8488IBZ?
The ISL8488IBZ is a 5V, low-power, full-duplex RS-485/RS-422 transceiver from Renesas Electronics in an 8-pin SOIC package. According to the Intersil manufacturer datasheet, the family uses BiCMOS circuitry, includes one driver and one receiver, and operates from a 4.5V to 5.5V supply. It is intended for balanced communications systems requiring both transmit and receive paths.
What is the operating voltage of ISL8488IBZ?
The ISL8488IBZ operates from a nominal 5V supply with a specified range of 4.5V to 5.5V. The Intersil manufacturer datasheet states that the family accepts supplies with 10% tolerance around 5V. Designers should verify that the selected system rail remains within this range during startup, load transients, and industrial supply variations.
Is ISL8488IBZ full duplex?
Yes, the ISL8488IBZ is a full-duplex RS-485/RS-422 transceiver with one driver and one receiver. The separate transmit and receive paths allow simultaneous two-way communication without sharing a driver between operating directions. This differs from a half-duplex implementation, which requires direction-control logic and cannot transmit and receive at the same time.
Where can I download the ISL8488IBZ datasheet PDF?
The ISL8488IBZ datasheet can be obtained from the Intersil or Renesas technical-documentation channels, with an indexed PDF copy also listed under the related ISL8488IBZ-T documentation. Review the manufacturer datasheet for the final pin table, electrical characteristics, recommended application circuit, and package information before releasing a PCB or production design.
Where is the ISL8488IBZ pinout?
The ISL8488IBZ uses an 8-pin SOIC package, and its authoritative pin assignment is shown in the manufacturer datasheet pinout and connection diagrams. The package drawing identifies the 8-SOIC footprint, while the functional connections include the driver, receiver, supply, ground, and interface terminals. Use the datasheet pin-description table when assigning PCB tracks.
What standards does ISL8488IBZ support?
The ISL8488IBZ supports RS-485 and RS-422 balanced communication interfaces. According to the Intersil manufacturer datasheet, the device family is designed for BiCMOS 5V operation and meets both listed standards. The correct external network components still depend on whether the design implements a point-to-point RS-422 link or a terminated RS-485 bus.
ISL8488IBZ vs ISL8488IBZ-T - which one should I select?
The ISL8488IBZ and ISL8488IBZ-T are listed as the same 1/1 full-duplex RS-485/RS-422 transceiver in an 8-SOIC package. The available comparison states that their terminals, packages, and main functional characteristics are consistent. The suffix primarily distinguishes ordering or packing configuration, so confirm the required shipment form against the manufacturer ordering guide.
Can SP3081EEN-L replace ISL8488IBZ?
The SP3081EEN-L is identified in an 8-pin SOIC comparison as a complete replacement for a related 8-pin, 4.5V, 250kbps version of the ISL8488 family. It is therefore a potential same-package alternative, but production use requires confirming the exact ISL8488IBZ suffix, data rate, driver and receiver logic levels, shutdown behavior, and pin mapping against the manufacturer datasheets.
When should I choose ISL8488IBZ over another RS-485 transceiver?
Choose the ISL8488IBZ when the design requires a 5V, full-duplex RS-485/RS-422 interface in an 8-pin SOIC and does not need functions absent from the device. Confirm the required data rate, logic levels, fault tolerance, and exact pin functions before final selection. A higher-rate or automotive-qualified alternative may be preferable when those additional requirements dominate.
Is ISL8488IBZ suitable for industrial automation equipment?
The ISL8488IBZ is suitable for industrial automation links that use 5V RS-485 or RS-422 balanced signaling and require a full-duplex 8-SOIC implementation. Its low-power BiCMOS design, 4.5V to 5.5V supply range, and integrated ESD protection align with equipment interfaces exposed to moderate electrical transients. Additional surge, isolation, and extended-temperature requirements need separate evaluation.
What is the best drop-in replacement for ISL8488IBZ?
The closest documented replacements are the Renesas Electronics ISL8488IBZ-T and ISL8488EIBZA, followed by the Exar Corporation SP3081EEN-L as a cross-brand candidate. All are identified as 8-pin SOIC devices, but a true drop-in decision depends on matching the exact data rate, enable or shutdown logic, driver state, receiver polarity, and every pin assignment. Compare those details before substituting.
What can replace ISL8488IBZ?
ISL8488IBZ can be replaced by the ISL8488IBZ-T or ISL8488EIBZA when their ordering details and electrical ratings match the installed version. The SP3081EEN-L is also listed as a complete replacement candidate in an 8-pin SOIC comparison. No replacement should be approved solely from package shape; verify pinout, supply range, data rate, logic polarity, and bus-drive behavior.
Is ISL8488IBZ the same as ISL8488EIBZA?
The ISL8488IBZ and ISL8488EIBZA are closely related 8-pin SOIC RS-485/RS-422 transceivers, and a comparison lists the latter as a complete replacement for the related family. They are not necessarily identical in every ordering or lifecycle attribute. Check the exact suffix definitions, temperature grade, data rate, and pin-level behavior in the manufacturer documentation before treating them as interchangeable.
Where to buy ISL8488IBZ online?
The ISL8488IBZ can be requested through the Request a Quote form on this page, where the exact MPN and quantity can be entered for current sourcing. Because pricing and stock can change rapidly, request a written quotation that confirms the 8-pin SOIC suffix, delivery quantity, and lead time. Do not substitute a different tape-and-reel or temperature suffix without reviewing the ordering code.
What is the price and lead time of ISL8488IBZ?
The current commercial terms for the ISL8488IBZ are available through the Request a Quote form on this page. Submit the required quantity, packaging preference, and destination to obtain a current quotation and lead-time confirmation. The part is identified as an 8-SOIC, 5V, full-duplex RS-485/RS-422 transceiver, so the final quotation should explicitly identify ISL8488IBZ rather than a nearby family member.
How should an ISL8488IBZ PCB be laid out?
Route each balanced pair as a closely coupled differential pair with a continuous ground reference, keep the connections short, and separate the interface from switching nodes and high-current paths. Place the supply-decoupling capacitor close to the device and use the manufacturer application circuit for termination, biasing, and protection. These steps reduce radiated noise and susceptibility to common-mode disturbance on the RS-485 or RS-422 link.

এর জন্য ইঞ্জিনিয়ারিং রেফারেন্স ডেটা ISL8488IBZ — তুলনা, ডিজাইন গাইডেন্স এবং কমপ্লায়েন্স তথ্য।

নির্বাচন গাইড

Choose the ISL8488IBZ when the design requires a 5V, full-duplex RS-485/RS-422 transceiver in an 8-pin SOIC and its electrical characteristics meet the interface requirements. ISL8488IBZ-T is the closest same-family choice because its documented functions and package match the target, making it suitable when the ordering or packing suffix is required. Consider ISL8488EIBZA when its documented 250 kbps configuration and exact pin behavior fit the board and production plan. Evaluate SP3081EEN-L when a cross-brand sourcing path is valuable and its data rate, logic levels, shutdown behavior, and pin functions have been checked against the installed ISL8488IBZ. In every case, package matching alone is insufficient; validate supply limits, data rate, bus-drive behavior, ESD requirements, and lifecycle expectations before substitution.

বিকল্পের সাথে তুলনা

পারামিটার এই পণ্য ISL8488IBZ-T ISL8488EIBZA SP3081EEN-L
Package 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC
Brand Renesas Electronics Renesas Electronics Renesas Electronics Exar Corporation
Nominal Supply Voltage 5 V 5 V 5 V 5 V
Documented Supply Range 4.5 V to 5.5 V 4.5 V to 5.5 V 4.5 V 4.5 V
Interface RS-485/RS-422 RS-485/RS-422 RS-485/RS-422 RS-485/RS-422
Transceiver Configuration 1/1 full duplex 1/1 full duplex 1/1 full duplex 1/1 full duplex

মূল পার্থক্যসমূহ

  • Documented exact-family drop-in ordering option (বনামISL8488IBZ-T)
  • Same-package Renesas family alternative with documented 250 kbps configuration (বনামISL8488EIBZA)
  • Cross-brand same-package replacement path (বনামSP3081EEN-L)

ডিজাইন নোট

Route both RS-485 and RS-422 signals as tightly coupled differential pairs with symmetrical geometry and a continuous ground reference. Keep the transceiver close to the board connector, minimize stub branches, and separate communication traces from switching nodes and high-current power paths. A controlled-impedance layout is helpful at higher data rates, but the manufacturer application diagram should remain the basis for component placement and connector protection.

Place the required supply-decoupling capacitor close to the 5V and ground pins to suppress local supply transients. The device operates across 4.5V to 5.5V, so verify that power-source tolerance, startup behavior, and regulator ripple remain inside that range. Use the manufacturer datasheet for the exact capacitor values and low-voltage or high-voltage guidance rather than estimating the network from the nominal 5V rail.

Do not treat a shared SOIC footprint as proof of electrical compatibility. Before replacing ISL8488IBZ with ISL8488IBZ-T, ISL8488EIBZA, or SP3081EEN-L, compare every pin name, receiver polarity, enable or shutdown behavior, bus-driver state, data rate, supply range, and thermal rating. The suffix and family-specific characteristics can determine whether a substitution is electrically identical or only functionally similar.

For industrial cabinets and long cables, use the manufacturer application circuit as the starting point for protection, termination, and bus biasing. ESD protection is present in the ISL8488 family, but it does not replace a complete surge or lightning-protection strategy. Keep the external protection network near the connector and route the balanced pair directly toward the transceiver to minimize antenna effects and common-mode conversion.

কমপ্লায়েন্স তথ্য

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
লিড ফ্রি
Unknown
হ্যালোজেন ফ্রি
Unknown
কনফ্লিক্ট মিনারেলস
Unknown

The device is an industrial communications interface IC, and no automotive qualification is identified. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status require confirmation from current manufacturer or distributor documentation.

ডেটা যাচাই করা হয়েছে: 2026-11-15 — ডেটা XAIPART-এর কম্পোনেন্ট ইঞ্জিনিয়ারিং টিম দ্বারা যাচাই ও কিউরেট করা হয়েছে

সম্পর্কিত অনুসন্ধান

ISL8488IBZ datasheet ISL8488IBZ pinout ISL8488IBZ datasheet pdf ISL8488IBZ specifications Renesas ISL8488IBZ ISL8488IBZ 8-SOIC ISL8488IBZ RS-485 transceiver ISL8488IBZ equivalent ISL8488IBZ replacement ISL8488IBZ vs ISL8488IBZ-T ISL8488IBZ footprint ISL8488IBZ price ISL8488IBZ stock ISL8488IBZ full duplex

সম্পর্কিত কম্পোনেন্ট ও শর্তাবলী

Renesas Electronics Intersil ISL8488IBZ ISL8488IBZ-T ISL8488EIBZA SP3081EEN-L RS-485 RS-422 full-duplex transceiver driver receiver balanced differential interface BiCMOS low-power communications IC interface IC 8-pin SOIC SOIC family surface-mount package 4.5V to 5.5V supply 5V power supply ESD protection industrial automation test and measurement data acquisition
তাৎক্ষণিক বিলওয়াছে রেকোজিউইট
সম্পূর্ণ বিবরণ পূরণ করুন — আমাদের সেলস টিম 24 ঘণ্টার মধ্যে উত্তর দেবে
পার্ট নম্বর উৎপাদক প্যাকেজ QTY লক্ষ্যমূল্য প্রসারিত
✓
বিল প্রস্তুত করা হয়েছে!

আমরা ২৪ ঘণ্টার মধ্যে আপনার ইমেইলে প্রত্যুত্তর দেব

1
RFQ জমা হয়েছে
2
কোটেশন পাওয়া গেছে
3
অর্ডার দেওয়া হয়েছে
4
পেমেন্ট
5
শিপ করা হয়েছে
6
ডেলিভারি হয়েছে
RFQ বিবরণ দেখুন