LMR321G-GTR - Low-Power Ground-Sense Op Amp | ROHM
MPN: LMR321G-GTR ✓ সক্রিয়LMR321G-GTR সারাংশ
An operational amplifier is an analog signal-processing IC that compares two input voltages and drives its output toward a level representing their difference. In a standard amplifier configuration, the feedback network determines the closed-loop gain, while the op-amp supplies high open-loop gain and signal amplification. The ground-sense configuration is particularly useful when the input signal is referenced to ground and the output must remain close to the ground rail. The LMR321G-GTR provides a single amplifier per package, simplifying designs that require only one active device.
ROHM describes the LMR321G as a low-voltage, low-power general-purpose operational amplifier with full-swing output. These characteristics make it suitable for battery-powered equipment, current-sense conditioning, sensor interfaces, and low-voltage control systems. The single-channel configuration reduces package count when additional amplifier channels are not required. Its 5-SSOP format also supports compact PCB layouts when compared with larger multi-channel packages.
The LMR321, LMR358, and LMR324 families provide single-, dual-, and quad-channel options in a related low-power product grouping. Engineers can therefore standardize on the LMR family while selecting the channel count that matches the circuit. The GTR ordering code identifies the single LMR321G device in a compact SSOP package with a tape-and-reel production configuration. Exact electrical limits, input/output ranges, current consumption, and stability requirements should be confirmed in the manufacturer datasheet before release to production.
Typical uses include amplifying signals from low-voltage sensors, buffering analog inputs, conditioning shunt-monitor signals in portable instruments, and providing general-purpose amplification in embedded systems. The full-swing output capability can simplify signal-chain design when the load and bias conditions are compatible with the device's operating region. In precision measurement paths, input offset voltage, input bias current, noise, common-mode range, and output-drive capability remain the principal selection criteria.
For layout, keep the feedback loop compact and connect the bypass capacitor close to the supply pins. Maintain the ground reference required by the amplifier circuit and avoid placing high-current return paths beneath sensitive analog signals. Confirm capacitive-load stability and output-current limits for the intended load. When replacing another five-pin amplifier, verify the package drawing, exposed-pad requirements, pin functions, supply range, common-mode range, and output-swing behavior rather than relying only on the package name.
This product page combines the manufacturer's device identity with distributor listings, package information, application guidance, comparison fields, and practical design notes. It is intended to accelerate component selection and PCB planning while keeping the final engineering decision tied to the official LMR321G datasheet.
এর জন্য ড্রপ-ইন বিকল্প LMR321G-GTR — একই package, pin-to-pin compatible। ভিন্ন package-এর যেসব পার্টে PCB rework প্রয়োজন সেগুলো বাদ দেওয়া হয়েছে।
এই পণ্যের জন্য কোনো ড্রপ-ইন বিকল্প পাওয়া যায়নি।
বিকল্প অনুরোধ করুনLMR321G-GTR সর্বোচ্চ রেটিং ও বৈদ্যুতিক বৈশিষ্ট্য
| Product Type | Operational Amplifier |
| Amplifier Type | Ground Sense Low-Power General-Purpose Operational Amplifier |
| Number of Circuits | 1 circuit |
| Number of Amplifiers | 1 amplifier |
| Supply Class | Low voltage |
| Output Swing | Full swing |
| প্যাকেজ | 5-SSOP |
| মাউন্টিং টাইপ | Surface Mount |
| Series | LMR Series |
| Family Members | LMR321, LMR358, and LMR324 |
| Channel Configurations | Single, dual, and quad |
LMR321G-GTR 5-ssop পিন কনফিগারেশন গাইড
LMR321G-GTR (5-ssop প্যাকেজ)-এর পিন কনফিগারেশন। এই অ্যানালগ কম্পোনেন্টে ইনপুট, আউটপুট ও পাওয়ার সাপ্লাই পিন রয়েছে। অফসেট নাল, কম্পেনসেশন ও এনেবল পিন কনফিগারেশনের জন্য প্রস্তুতকারকের ডেটাশিট দেখুন। সিগন্যাল কন্ডিশনিং ও অ্যামপ্লিফায়ার সার্কিটের জন্য আদর্শ।
এর জন্য বিস্তারিত পিনআউট ডেটা পাওয়া যায়নি LMR321G-GTR.
দেখুন ডেটাশিট সম্পূর্ণ পিন কনফিগারেশনের জন্য।
সাধারণ ব্যবহার
LMR321G-GTR এর জন্য উপযুক্ত 6 অ্যাপ্লিকেশনs: Battery-Powered Sensor Conditioning, Portable Instrument Signal Amplification, Ground-Referenced Current Monitoring, Industrial Low-Voltage Control Interface, IoT Sensor Node, Audio and Communication Input Buffer.
Battery-Powered Sensor Conditioning
The LMR321G-GTR fits low-voltage sensor interfaces because it is a single-channel, low-power, ground-sense operational amplifier designed for low-voltage operation and full-swing output. It can amplify or buffer a sensor signal referenced to ground while keeping the analog front end compact. A designer should place the amplifier close to the sensor connection, maintain a short feedback path, and confirm that the sensor's operating range fits the amplifier's specified common-mode and supply limits. The 5-SSOP package also helps reduce board area compared with a larger single-amplifier package, while the single-channel configuration avoids carrying unused amplifier channels.
সুপারিশকৃত
Portable Instrument Signal Amplification
The LMR321G-GTR is suitable for portable instrumentation that needs one low-voltage amplification stage without a multi-amplifier package. Its ground-sense architecture is appropriate for signals operating near the ground rail, and the full-swing output can support downstream conversion when the load and bias conditions remain within the operating limits. In an instrument, the amplifier can buffer a transducer output before an ADC, reducing loading of the sensing element. Layout should prioritize short input paths, a compact feedback network, and a clean return connection to prevent injected ground noise from becoming signal error.
সুপারিশকৃত
Ground-Referenced Current Monitoring
The LMR321G-GTR can be used to condition a ground-referenced voltage in a current-monitoring circuit, such as a signal derived from a shunt or sensor element. The single low-power amplifier provides gain without requiring a dual or quad package when only one monitoring path is present. Its ground-sense focus is useful when the measured voltage is small relative to the supply rail. The engineer should verify common-mode range, output swing, offset voltage, and the effect of input bias current on the smallest detectable signal, then include the amplifier's error budget in the system measurement calculation.
সুপারিশকৃত
Industrial Low-Voltage Control Interface
The LMR321G-GTR is applicable to low-voltage industrial control interfaces that require a compact, general-purpose amplifier for sensor or control signals referenced to ground. Its low-voltage, low-power positioning supports designs that cannot accommodate a higher-current amplifier, while the single 5-SSOP package keeps the footprint controlled. The device can amplify a control or feedback node before level conversion or ADC acquisition. Practical implementation requires a low-impedance supply source, local supply bypassing, careful grounding, and verification that the output remains within its rated swing when connected to the next circuit stage.
সুপারিশকৃত
IoT Sensor Node
The LMR321G-GTR can serve as the analog conditioning stage in a compact IoT sensor node that converts a low-level, ground-referenced sensor output into a voltage suitable for downstream sampling. The single-channel low-power architecture fits nodes that need one amplification path rather than several amplifier functions. Because the node may combine sensitive sensing with digital switching activity, place the LMR321G-GTR near the sensor and separate its analog return path from switching currents. Confirm supply-current consumption and noise behavior across the node's operating conditions, and use the manufacturer stability data when the input or feedback network includes appreciable capacitance.
সুপারিশকৃত
Audio and Communication Input Buffer
The LMR321G-GTR can buffer a weak, ground-referenced analog input in compact audio or communication equipment where low-voltage operation and low supply-current consumption are important. The full-swing output provides flexibility when the next stage operates near the lower supply rail, subject to the device's specified output-loading and bias conditions. The amplifier should be positioned away from clocks, switching regulators, and high-current return paths to minimize coupled noise. Confirm the required bandwidth, slew rate, common-mode range, and output-drive capability against the signal path before selecting it for high-fidelity or high-speed communication functions.
সুপারিশকৃত
সুপারিশকৃত পণ্যের সারসংক্ষেপ
এর জন্য ইঞ্জিনিয়ারিং রেফারেন্স ডেটা LMR321G-GTR — তুলনা, ডিজাইন গাইডেন্স এবং কমপ্লায়েন্স তথ্য।
নির্বাচন গাইড
বিকল্পের সাথে তুলনা
| পারামিটার | এই পণ্য |
|---|---|
| Package | 5-SSOP |
| Brand | ROHM Semiconductor |
| Product Type | Operational Amplifier |
| Amplifier Configuration | Single amplifier |
| Circuit Count | 1 circuit |
| Operating Class | Low voltage, low power |
| Signal Reference | Ground sense |
| Output Capability | Full swing |
| Series | LMR Series |
| Mounting Type | Surface Mount |
মূল পার্থক্যসমূহ
- Single-channel packaging matches one-stage analog designs (বনামLMR358 dual-channel family member)
- Ground-sense positioning for low-level signal conditioning (বনামGeneric five-pin operational amplifier)
- Low-power family positioning (বনামHigher-current general-purpose amplifier)
ডিজাইন নোট
Place the LMR321G-GTR close to the signal source and connect the bypass capacitor directly to the supply and ground pins. Keep the feedback loop compact so that the loop encloses the smallest possible area and avoids coupling from switching nodes. Route sensitive input and feedback traces over a continuous ground plane, while keeping high-current switching returns and inductor connections away from the amplifier ground reference.
Do not treat a matching package outline as proof of drop-in compatibility. Before substituting another amplifier, compare the official pin description, supply range, input common-mode range, output swing, input bias current, offset voltage, stability with the selected feedback network, and package dimensions. In particular, verify whether the alternate device requires an exposed pad, different pin functions, or a different DC bias arrangement.
Use the shortest practical route from the source to the amplifier input and return the feedback components to the amplifier side of the board. For sensor signals in the millivolt range, account for offset voltage and input bias current when resolving the smallest meaningful measurement. If driving a cable, long trace, or capacitive load, confirm stability and output drive from the manufacturer datasheet rather than relying only on nominal amplifier bandwidth.
Design the supply rail so the amplifier never operates below its specified supply range and the output does not exceed its rated swing under the actual load. Estimate the device's average supply-current contribution using the operating voltage and load conditions, then include it in the power budget. Local decoupling helps the amplifier respond to supply disturbance, but it does not replace an upstream supply designed with adequate low-frequency headroom.
কমপ্লায়েন্স তথ্য
The device is an operational amplifier rather than an automotive-qualified power semiconductor. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status require confirmation from the current manufacturer documentation or declaration.