LT1787HS8 - Precision High-Side Current Sense Amp | Analog Devices
MPN: LT1787HS8 ✓ সক্রিয়LT1787HS8 সারাংশ
A high-side current-sense amplifier is an instrumentation amplifier optimized for measuring small differential voltages created by current flowing through a sense resistor. It belongs to the current-sense amplifier category, which is part of the broader amplifier IC hierarchy and supports power management, battery monitoring, motor control, and system protection. Unlike a low-side measurement arrangement, high-side sensing preserves the ground connection and can measure current in either supply or return conductor without disturbing the powered load.
The LT1787 offers several features useful in precision applications. Its 40 µV typical input offset voltage helps preserve measurement accuracy when the differential signal is small, while the stated 75 µV maximum offset provides a defined worst-case limit. Bidirectional sensing allows the amplifier to distinguish positive from negative current, and the greater-than-12-bit dynamic range provides useful resolution across a broad measurement range. A 60 µA operating current also supports low-power system designs where every milliamp can affect battery life.
The device monitors the differential voltage across a user-selected external sense resistor rather than integrating current directly through the amplifier inputs. This approach allows the sensing range to be adjusted by choosing the resistor value and power rating. The resulting output represents the measured current direction and magnitude, but accuracy still depends on resistor tolerance, temperature coefficient, Kelvin connection of the sense traces, amplifier offset, and the selected gain configuration.
Typical uses include battery-powered equipment, portable instruments, industrial current monitoring, power supplies, motor-control systems, and load-current measurement. In a battery application, the low 60 µA operating current helps limit control-circuit overhead. In a precision power supply, bidirectional sensing can support current sharing or load reporting. The external sense resistor must be selected so that maximum expected current produces a manageable differential input voltage without excessive resistor dissipation.
A critical layout requirement is to route the sense-resistor connections as a differential pair directly to the amplifier inputs. Keep these traces short, minimize their enclosed area, and use a Kelvin connection at the resistor pads. Avoid sharing sensitive sense traces with switching-node or high-current return paths, because parasitic resistance and common-mode pickup can obscure the measured signal even when the amplifier itself has low offset voltage.
This page combines manufacturer electrical characteristics, lifecycle status, packaging details, practical application guidance, and carefully qualified drop-in alternatives. It also highlights the distinction between electrical drop-in suitability and non-equivalent cross-reference candidates, helping engineers evaluate PCB reuse, temperature grade, and measurement accuracy before making a replacement decision.
এর জন্য ড্রপ-ইন বিকল্প LT1787HS8 — একই package, pin-to-pin compatible। ভিন্ন package-এর যেসব পার্টে PCB rework প্রয়োজন সেগুলো বাদ দেওয়া হয়েছে।
LT1787HS8#PBF
✅ ড্রপ-ইন📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)
LT1787CS8#PBF
✅ ড্রপ-ইন📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)
LT1787CMS8
✅ ড্রপ-ইন📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)
LT1787HS8 সর্বোচ্চ রেটিং ও বৈদ্যুতিক বৈশিষ্ট্য
| Product Type | Precision high-side current-sense amplifier |
| Maximum Input Offset Voltage | 75 µV |
| Typical Input Offset Voltage | 40 µV |
| Dynamic Range | Greater than 12 bits |
| Operating Current | 60 µA |
| Supply Operation | Up to 60 V for LT1787HV |
| Current Measurement Direction | Bidirectional |
| Sense Resistor | User-selected external resistor |
| আউটপুট টাইপ | Current or voltage output |
| Power Class | Micropower |
| Number of Circuits | 1 amplifier |
| প্যাকেজ | 8-pin SO |
| মাউন্টিং টাইপ | Surface mount |
| Manufacturer | Analog Devices |
| লাইফসাইকেল স্ট্যাটাস | Production |
| RoHS স্ট্যাটাস | Unknown |
| REACH Status | Unknown |
| AEC-Q100 Qualification | Not applicable |
LT1787HS8 8-pin so পিন কনফিগারেশন গাইড
LT1787HS8 (8-pin so প্যাকেজ)-এর পিন কনফিগারেশন। এই অ্যানালগ কম্পোনেন্টে ইনপুট, আউটপুট ও পাওয়ার সাপ্লাই পিন রয়েছে। অফসেট নাল, কম্পেনসেশন ও এনেবল পিন কনফিগারেশনের জন্য প্রস্তুতকারকের ডেটাশিট দেখুন। সিগন্যাল কন্ডিশনিং ও অ্যামপ্লিফায়ার সার্কিটের জন্য আদর্শ।
এর জন্য বিস্তারিত পিনআউট ডেটা পাওয়া যায়নি LT1787HS8.
দেখুন ডেটাশিট সম্পূর্ণ পিন কনফিগারেশনের জন্য।
সাধারণ ব্যবহার
LT1787HS8 এর জন্য উপযুক্ত 6 অ্যাপ্লিকেশনs: Battery-Powered Load Monitoring, Industrial Power-Supply Load Reporting, Motor Drive Current Feedback, Portable Instrument Current Sensing, Battery Charger Input Monitoring, Server and Network Power Monitoring.
Battery-Powered Load Monitoring
The LT1787HS8 fits portable equipment that must measure current drawn from a battery without placing an instrumented ground link in the load path. Its 60 µA operating current limits measurement overhead, while the 40 µV typical input offset voltage helps retain accuracy when the selected sense resistor develops only a small differential voltage. The amplifier is placed across the high-side sense-resistor pads and produces a current or voltage output representing magnitude and direction. System accuracy still depends on the resistor’s tolerance and temperature coefficient, so a low-TC part and a Kelvin connection remain important.
সুপারিশকৃত
Industrial Power-Supply Load Reporting
The LT1787HS8 is suitable for reporting load current in an industrial power supply where the measured conductor is at high side and must remain electrically connected to the system ground. Its greater-than-12-bit dynamic range provides useful resolution across the sense-resistor input range, while bidirectional operation can distinguish charging from discharging when the circuit supports it. Place the device across a user-selected external sense resistor and route the two inputs differentially. The main design trade-off is resistor dissipation: increasing sensitivity raises output resolution but also increases the voltage dropped and power dissipated in the sensing element.
সুপারিশকৃত
Motor Drive Current Feedback
The LT1787HS8 can provide motor-current feedback for control and protection because it measures a differential sense-resistor voltage and supports bidirectional current detection. The 40 µV typical offset is useful when motor current information must be resolved at relatively small sense voltages. In a motor circuit, use a low-inductance sense resistor with an appropriate pulse rating and connect it directly to the amplifier inputs. Placement away from switching-node copper and careful common-mode analysis are essential because motor transients can exceed the clean laboratory conditions assumed for ordinary current measurements.
সুপারিশকৃত
Portable Instrument Current Sensing
The LT1787HS8 fits precision handheld instruments where current consumption and measurement resolution must coexist. Its micropower 60 µA operating current reduces the burden introduced by continuous sensing, while bidirectional operation can support charge, discharge, or reversed-polarity measurements. Use an external sense resistor selected for the instrument’s current range, then convert the amplifier output with the system ADC. Avoid overstating accuracy from the 40 µV typical offset alone: resistor tolerance, ADC input noise, reference accuracy, and analog trace coupling can dominate a practical instrument-level uncertainty budget.
সুপারিশকৃত
Battery Charger Input Monitoring
The LT1787HS8 can monitor input or output current in a battery-charger power path by sensing the differential voltage across a series resistor. Bidirectional measurement allows the controller to distinguish source current from return current, provided the circuit and output configuration support that operating condition. The device’s low offset helps preserve measurement resolution around low-current transitions, and its 60 µA operating current is valuable in energy-conscious designs. The sense resistor must be rated for continuous and transient current, while the amplifier’s supply and input limits must be checked against the charger’s operating voltage and fast transient environment.
সুপারিশকৃত
Server and Network Power Monitoring
The LT1787HS8 is applicable to precision power-rail telemetry in servers, networking equipment, and other systems that need to verify current consumption. The high-side arrangement preserves the load’s ground reference and the amplifier’s 75 µV maximum offset provides a defined device-level limit for error analysis. Use a low-TC external sense resistor and connect it with dedicated high-impedance traces to avoid voltage drops in copper. Because the device is micropower rather than a high-bandwidth monitor, it is best suited to steady or slowly changing current measurement rather than transient waveform capture without additional circuitry.
সুপারিশকৃত
সুপারিশকৃত পণ্যের সারসংক্ষেপ
এর জন্য ইঞ্জিনিয়ারিং রেফারেন্স ডেটা LT1787HS8 — তুলনা, ডিজাইন গাইডেন্স এবং কমপ্লায়েন্স তথ্য।
নির্বাচন গাইড
বিকল্পের সাথে তুলনা
| পারামিটার | এই পণ্য | LT1787HS8#PBF | LT1787CS8#PBF | LT1787CMS8 |
|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | 8-pin SO | 8-pin SO | 8-pin SO | 8-pin SO |
| Product Type | Precision high-side current-sense amplifier | Precision high-side current-sense amplifier | Precision high-side current-sense amplifier | Precision high-side current-sense amplifier |
| Typical Input Offset Voltage | 40 µV | 40 µV | 40 µV | 40 µV |
| Maximum Input Offset Voltage | 75 µV | 75 µV | 75 µV | 75 µV |
| Operating Current | 60 µA | 60 µA | 60 µA | 60 µA |
| Dynamic Range | Greater than 12 bits | Greater than 12 bits | Greater than 12 bits | Greater than 12 bits |
| Current Measurement Direction | Bidirectional | Bidirectional | Bidirectional | Bidirectional |
| Sense Resistor | User-selected external resistor | User-selected external resistor | User-selected external resistor | User-selected external resistor |
| Output Type | Current or voltage output | Current or voltage output | Current or voltage output | Current or voltage output |
মূল পার্থক্যসমূহ
- Lower stated offset than a conventional 250 mV full-scale current-sense amplifier (বনামAD627AR)
- Higher specified dynamic range (বনামAD627AR)
- Lower control-circuit operating current (বনামAD627AR)
- Bidirectional current indication with external resistor control (বনামAD627AR)
ডিজাইন নোট
Connect the two sense inputs directly to the corresponding pads of the external sense resistor using a differential pair. The analog manufacturer documentation recommends minimizing parasitic resistance and inductance in these paths. Use separate sense taps or a Kelvin connection so that current flowing through the power copper does not add an unintended voltage to the measured differential signal. Place the amplifier and its input network close to the sense resistor when practical.
Do not select the sense resistor from sensitivity alone. Its value sets both the amplifier input span and the I²R power loss at maximum current. Its power rating, pulse capability, tolerance, and temperature coefficient directly affect accuracy. Because the LT1787 has a 40 µV typical input offset, a high-value resistor can make sense-resistor tolerance dominate the measurement error. Calculate worst-case error across tolerance, temperature, and offset before releasing the design.
Keep the high-current sense path separate from the amplifier’s low-level input traces. Avoid routing inputs beneath or parallel to switching nodes, motor phases, or inductive power loops. If the measured conductor is subject to fast transients, verify the common-mode and supply limits for the exact LT1787HS8 ordering code in the manufacturer datasheet. A small protection network can help, but its capacitance and leakage must remain compatible with the required measurement bandwidth and accuracy.
The amplifier’s 60 µA operating current is suitable for micropower systems, but the complete sensing circuit can consume more power through the sense resistor and output load. Check the output configuration before connecting a downstream ADC or microcontroller input. Also verify that the amplifier supply remains present while measurements are required and that shutdown behavior, if used, does not create an unexpected output state at the ADC input.
কমপ্লায়েন্স তথ্য
The manufacturer identifies the LT1787 family as a production product, but the product-page and search information do not provide RoHS, REACH, halogen-free, conflict-minerals, or automotive qualification statements. The #PBF ordering suffix is recorded separately; the exact packaging and termination details should be confirmed in the manufacturer ordering table.