MC14C88BP - Quad Low-Power RS-232 Driver | onsemi
MPN: MC14C88BP ✓ সক্রিয়MC14C88BP সারাংশ
A quad RS-232 line driver converts TTL or CMOS logic signals into differential RS-232-compatible levels. In the interface hierarchy, an RS-232 driver sits between digital logic and a communication transceiver, with the complete transceiver combining drivers, receivers, and signal conditioning. This device is useful where one controller must connect to four separate data, control, or handshake lines without using four single-channel driver packages.
The BiMOS process combines bipolar output drive with CMOS-compatible input circuitry. This supports low quiescent current while maintaining the voltage swing and transition behavior required by RS-232 interfaces. Inputs accept both TTL and CMOS levels with minimal loading, while internal slew-rate control limits unwanted high-frequency energy on the driven lines. These characteristics make the MC14C88BP appropriate for low-power industrial control, instrumentation, and embedded communication equipment.
Each channel provides one driver output, allowing four logic signals to be translated independently. Internal slew-rate control helps reduce edge-rate problems that can otherwise produce ringing, crosstalk, or electromagnetic interference on long cables. The device's low-power design is particularly valuable in battery-operated or power-constrained systems where every milliwatt of static consumption affects operating time or thermal design.
Typical uses include RS-232 port expansion, industrial controller interfaces, test and measurement equipment, and embedded systems that require four RS-232 outputs. The part can also support point-to-point links when several channels remain unused. In each case, system designers should confirm output levels, grounding, cable length, and interface requirements against the original equipment specification.
For reliable PCB implementation, place the MC14C88BP in the same orientation as the reference design and observe the datasheet's supply and ground connections. Decoupling capacitors should be placed close to the power pins, while unused driver inputs must be tied to a defined logic level. Because RS-232 is unbalanced, grounding and cable routing remain important even though the driver itself internally controls output slew rate.
This product record combines the MC14C88BP's functional characteristics with application guidance, engineering cautions, and verified drop-in references. It also distinguishes explicitly identified compatible parts from options that are merely similar, helping engineers assess PCB reuse, supply planning, and signal-interface integrity before making a replacement decision.
এর জন্য ড্রপ-ইন বিকল্প MC14C88BP — একই package, pin-to-pin compatible। ভিন্ন package-এর যেসব পার্টে PCB rework প্রয়োজন সেগুলো বাদ দেওয়া হয়েছে।
এই সিরিজের ভ্যারিয়েন্ট
একই সিরিজের মডেল যেগুলো drop-in compatible MC14C88BP (একই form factor এবং footprint) — পার্থক্য রয়েছে Mounting Type, Number of Drivers.
MC1488NE4
✅ ড্রপ-ইনমূল্যের জন্য যোগাযোগ করুন
ডেটাশিট দেখুন →DS1488
✅ ড্রপ-ইন📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)
MC14C88BP বিশেষণ
| Device Type | Quad low-power RS-232 line driver |
| Technology | BiMOS |
| Number of Drivers | 4 channels |
| Input Compatibility | TTL and CMOS |
| Input Loading | Minimal |
| Output Slew Rate | Internally controlled |
| Power Consumption | < 5.0 mW |
| কুইসেন্ট কারেন্ট | < 160 uA |
| EIA-232-D Compliance | Conforms |
| EIA-562 Compliance | Conforms |
| CCITT V.28 Compliance | Conforms |
| Package Type | 14-pin plastic DIP |
| মাউন্টিং টাইপ | Through-hole |
MC14C88BP 14-pin plastic dip পিন কনফিগারেশন গাইড
MC14C88BP (14-pin plastic dip প্যাকেজ)-এর পিন কনফিগারেশন। পিন নম্বরিং, ফাংশন এবং সংযোগ ডায়াগ্রাম প্রস্তুতকারকের ডেটাশিটে সংজ্ঞায়িত করা আছে। সঠিক ফুটপ্রিন্ট এবং সোল্ডারিং নির্দেশিকার জন্য এটি দেখুন।
এর জন্য বিস্তারিত পিনআউট ডেটা পাওয়া যায়নি MC14C88BP.
দেখুন ডেটাশিট সম্পূর্ণ পিন কনফিগারেশনের জন্য।
সাধারণ ব্যবহার
MC14C88BP এর জন্য উপযুক্ত 6 অ্যাপ্লিকেশনs: Industrial RS-232 Controller Interface, Multichannel Data Port Expansion, Test and Measurement Equipment, Embedded Communication Equipment, Point-to-Point Serial Links, Legacy Equipment Communication Retrofit.
Industrial RS-232 Controller Interface
The MC14C88BP fits an industrial controller that must convert four TTL or CMOS logic signals into RS-232-compatible outputs. Its four driver channels reduce the component count compared with four single-channel devices, while operation below 5.0 mW and quiescent current below 160 uA support power-conscious controller designs. Internally controlled slew rate helps limit ringing and electromagnetic interference on board-level connections. The designer should pair the driver with the connector protection network, grounding scheme, and any receiver required by the communication architecture.
সুপারিশকৃত
Multichannel Data Port Expansion
The MC14C88BP can expand a digital controller with four separately driven RS-232 lines for data, status, and handshake signals. Its monolithic quad BiMOS implementation places four channels in one 14-pin DIP, reducing board area and simplifying the shared supply arrangement. TTL and CMOS-compatible inputs allow connection to common embedded logic, and internal slew-rate control improves signal-edge behavior. Each unused output should be left in the state recommended by the manufacturer logic table, while signal grounds should follow the equipment's interface-reference design.
সুপারিশকৃত
Test and Measurement Equipment
The MC14C88BP is useful in test and measurement instruments that require several low-power RS-232 outputs for instrument control or status reporting. Four channels can drive separate control commands without duplicating the driver circuitry, and the below-5.0 mW power figure reduces system-level thermal burden. Internal slew-rate control provides more controlled transitions than unrestricted RS-232 outputs, which is advantageous when cables or test fixtures create capacitive loading. System designers must still verify timing, grounding, and protection requirements for the specific connector configuration.
সুপারিশকৃত
Embedded Communication Equipment
The MC14C88BP suits embedded systems needing multiple RS-232 outputs from a microcontroller or programmable logic interface. Its TTL- and CMOS-compatible inputs minimize logic interfacing complexity, while quiescent current below 160 uA helps preserve power budgets in embedded products. The four-channel quad arrangement supports concurrent control and status lines or a mixture of communications and supervisory signals. Firmware designers should define safe states for inactive channels, and hardware engineers should confirm that the external connector protection scheme can handle the intended cable environment.
সুপারিশকৃত
Point-to-Point Serial Links
Although designed as a quad driver, MC14C88BP can support a point-to-point interface when only one or two channels are active. Its low-power operation preserves system headroom, and internal slew-rate control limits unwanted edge energy on the driven line. Additional active channels increase switching activity and therefore dynamic power, so the final thermal budget should reflect the intended data rate and workload. Firmware should avoid unnecessary toggling and maintain defined levels on unused inputs to prevent unpredictable outputs.
সুপারিশকৃত
Legacy Equipment Communication Retrofit
The MC14C88BP is appropriate when maintaining or expanding a legacy RS-232 interface in existing equipment. The 14-pin plastic DIP package supports through-hole construction and the manufacturer explicitly identifies pin-compatible replacement families, which helps engineers evaluate board reuse. Before substitution, compare the complete connection tables because legacy RS-232 drivers may differ in enable handling, supply pins, and behavior of unused channels. The retrofit should retain the original grounding and protection strategy unless the updated interface specification permits improvements.
সুপারিশকৃত
সুপারিশকৃত পণ্যের সারসংক্ষেপ
এর জন্য ইঞ্জিনিয়ারিং রেফারেন্স ডেটা MC14C88BP — তুলনা, ডিজাইন গাইডেন্স এবং কমপ্লায়েন্স তথ্য।
নির্বাচন গাইড
বিকল্পের সাথে তুলনা
| পারামিটার | এই পণ্য | MC1488NE4 | DS1488 |
|---|---|---|---|
| Package | 14-pin plastic DIP | 14-pin plastic DIP | 14-pin plastic DIP |
| Brand | onsemi | onsemi | Texas Instruments |
| Function | Quad low-power RS-232 line driver | Quad RS-232 line driver | Quad RS-232 line driver |
| Driver Channels | 4 | 4 | 4 |
| Interface Standards | EIA-232-D, EIA-562, CCITT V.28 | RS-232-compatible line driver | RS-232-compatible line driver |
মূল পার্থক্যসমূহ
- Lower specified standby demand (বনামMC1488NE4)
- Documented interface conformance (বনামDS1488)
- Four-channel integration in one package (বনামMC1488NE4)
- Controlled output transitions (বনামDS1488)
ডিজাইন নোট
Follow the manufacturer pin-description table when assigning the 14-pin DIP footprint, including all supply, ground, and unused inputs. Keep the package orientation consistent with the printed pin-1 mark and the board's silkscreen. Place the required supply-decoupling capacitor close to the device's supply and ground pins, and route each driver output directly toward its associated interface network rather than sharing long traces with unrelated digital signals.
Do not treat every device named in the compatibility statement as an automatic same-footprint replacement. SN75188, SN75C188, and DS14C88 may provide related functions while differing in package or enable arrangements. Verify pin names, dimensions, supply limits, output voltage levels, and unused-input behavior for MC1488NE4 or DS1488 before approving a PCB substitution.
Use the internally controlled output transitions to minimize ringing and high-frequency energy on RS-232 lines. Keep driver outputs away from clocks, switching-regulator nodes, and sensitive analog inputs, and route the interface ground according to the equipment grounding plan. External protection and filtering should be selected for the actual cable length, connector exposure, and ESD environment rather than added only at the IC pins.
Estimated: power dissipation is approximately VIN multiplied by total supply current when the output load is negligible. For example, at a 5 V supply and 100 uA total current, the estimated dissipation is 0.0005 W. Confirm the actual supply voltage and dynamic current in the final design; the device is specified below 5.0 mW under the manufacturer's stated conditions.
কমপ্লায়েন্স তথ্য
No specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declarations were identified for MC14C88BP.
