SN74LS390N - Dual 4-Bit Decade Counter | Texas Instruments
MPN: SN74LS390N ✓ সক্রিয়SN74LS390N সারাংশ
A decade counter is a synchronous sequential digital circuit that advances through ten states, representing decimal digits 0 through 9. Two counter elements in one IC can provide independent decimal counting channels or be combined with external logic for larger counting ranges. Within the broader logic hierarchy, the SN74LS390N belongs to the 74LS TTL family of counters and dividers, which are bipolar logic integrated circuits used for dependable operation across established industrial and legacy digital systems.
The principal feature is the combination of two 4-bit decade counters in one package. The device is identified as a negative-edge counter IC, so its clock transitions are referenced to the falling edge. According to the Texas Instruments product description, each LS390 counter contains four ripple stages divided into separate divide-by-two and divide-by-five sections, with a separate clock input associated with each section. This architecture supports conventional decade sequencing when the sections are connected in the required manner.
The SN74LS390N is a dual counter rather than a binary-counter-only device. Each half implements a 4-bit decade count, providing ten decoded states per counter. Designers can therefore divide a known input frequency by ten, accumulate input pulses modulo ten, or build cascaded decimal counters by connecting the appropriate outputs of one counter to the clock input of another. The exact propagation-delay, operating-voltage, and current limits should be taken from the manufacturer datasheet for the selected production and temperature variant.
Typical applications include industrial frequency dividers, batch and piece counters, event-counting modules, electronic test equipment, timing references, and legacy control systems. The dual-counter arrangement saves board area when two independent channels are required. Through-hole assembly also remains useful for prototypes, repair boards, and industrial products where manually or automatically inserted DIP components are preferred over fine-pitch surface-mount packages.
When laying out the circuit, keep clock traces short and route them away from noisy switching nodes. Decouple the supply pin close to the IC, maintain a common ground reference for every counter connection, and check the required clock edge and output count sequence against the intended design. For cascaded decimal counting, confirm the correct output-to-clock connection and account for cumulative propagation delay.
This product page combines the manufacturer function description, distributor package identification, and practical implementation guidance. It also organizes same-footprint counter options, pinout location, package details, and design considerations to help engineers evaluate the SN74LS390N before schematic capture and PCB layout.
এর জন্য ড্রপ-ইন বিকল্প SN74LS390N — একই package, pin-to-pin compatible। ভিন্ন package-এর যেসব পার্টে PCB rework প্রয়োজন সেগুলো বাদ দেওয়া হয়েছে।
SN74LS390N
✅ ড্রপ-ইনমূল্যের জন্য যোগাযোগ করুন
ডেটাশিট দেখুন →SN74LS390N
✅ ড্রপ-ইনমূল্যের জন্য যোগাযোগ করুন
ডেটাশিট দেখুন →MC74HC390ANG
✅ ড্রপ-ইন📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)
SN74LS390N সর্বোচ্চ রেটিং ও বৈদ্যুতিক বৈশিষ্ট্য
| Counter Type | Dual 4-bit decade counter |
| Number of Counter Elements | 2 elements |
| Bits per Counter | 4 bits |
| Count Sequence | Decade, 0000 through 9999 |
| Clock Edge | Negative edge |
| Architecture | 4-stage ripple counter |
| Internal Counter Sections | Divide-by-two and divide-by-five sections per counter |
| Clock Inputs | Separate clock input for each section |
| Logic Family | 74LS TTL |
| প্যাকেজ | 16-pin PDIP |
| মাউন্টিং টাইপ | Through-hole |
SN74LS390N 16-pin pdip পিন কনফিগারেশন গাইড
SN74LS390N (16-pin pdip প্যাকেজ)-এর পিন কনফিগারেশন। এই ডিজিটাল IC-তে GPIO, কমিউনিকেশন ইন্টারফেস (UART, SPI, I2C) এবং পাওয়ার পিন রয়েছে। বিকল্প পিন ফাংশন ও কনফিগারেশন অপশনের জন্য প্রস্তুতকারকের ডেটাশিট দেখুন। এমবেডেড সিস্টেম ডিজাইন ও PCB লেআউটের জন্য অপরিহার্য।
এর জন্য বিস্তারিত পিনআউট ডেটা পাওয়া যায়নি SN74LS390N.
দেখুন ডেটাশিট সম্পূর্ণ পিন কনফিগারেশনের জন্য।
সাধারণ ব্যবহার
SN74LS390N এর জন্য উপযুক্ত 6 অ্যাপ্লিকেশনs: Industrial Frequency Divider, Pulse and Piece Counter, Legacy Control-System Timing, Digital Test and Measurement Equipment, Display and Digit Sequencing, Service and Repair Electronics.
Industrial Frequency Divider
The SN74LS390N is suitable for dividing a repetitive industrial signal by ten when one counter half is connected using its divide-by-two and divide-by-five sections. This architecture lets the input transition through ten states rather than eight, which is useful for timing strobes, sampling triggers, and repetitive actuator cycles. The dual-counter package can also maintain a second divided channel for a related process event. The negative-edge clock designation must be respected when defining the trigger point. For dependable operation, check the incoming frequency against the manufacturer timing limits, route the clock away from switching-power nodes, and use a common ground reference between the counter and the signal source.
সুপারিশকৃত
Pulse and Piece Counter
The two independent decade counters in the SN74LS390N can count pulses modulo ten in separate production or inspection channels. A sensor-conditioned pulse train can drive the clock input, while the four outputs of each half represent decimal states for display multiplexing, latch control, or event counting. Using both halves in one 16-pin PDIP reduces component count compared with separate single-counter packages. The implementation should include input conditioning that prevents ringing from being counted as an extra transition. Decoupling near the supply connection, defined levels on unused inputs, and propagation-delay margin are essential when counting fast or irregular event streams.
সুপারিশকৃত
Legacy Control-System Timing
The SN74LS390N fits legacy TTL control boards that require stable decade sequencing for relay timers, cycle counters, and sequential command stages. Its 74LS interface works naturally with other bipolar TTL logic, allowing one device to replace separate decade-counter stages in a repair or redesign. The four-stage ripple architecture provides a conventional solution for cascaded digit sequencing, while the dual halves can handle related count tasks. Because legacy equipment may use long signal paths or older power supplies, validate input levels and clock waveforms at the actual board connector. Confirm ground continuity and bypass the supply locally rather than relying on a distant bulk capacitor.
সুপারিশকৃত
Digital Test and Measurement Equipment
The SN74LS390N can organize repetitive test sequences, divide a reference frequency, and provide decade-state decoding in older bench instruments. Each counter half is useful for a separate measurement phase or as a cascaded digit in a frequency-divider chain. Its 16-pin PDIP construction also suits serviceable laboratory equipment that uses socketed logic packages. Designers should account for the accumulated delay through four ripple stages when maximum clock frequency matters and avoid decoding transient outputs without the appropriate synchronization scheme. Short clock routing, local supply bypass, and careful grounding are especially important when the instrument also contains high-gain analog or switching circuits.
সুপারিশকৃত
Display and Digit Sequencing
The SN74LS390N can drive decade-state logic for multiplexed seven-segment displays, digit-selection counters, and cyclic indicator sequences. Two counter halves provide separate decimal positions or independent count channels, reducing the number of packages needed on a compact logic board. The negative-edge count behavior must be coordinated with the display latch so that decoded outputs remain stable during the visible interval. Use the manufacturer output descriptions to select the correct decade state for each stage, and account for ripple propagation when multiple digits change together. Add output-stage drive components only after checking the required current and voltage limits.
সুপারিশকৃত
Service and Repair Electronics
The SN74LS390N is a practical choice for repairing older TTL instruments, industrial controllers, access-control equipment, and educational logic systems that use a 16-pin dual decade counter. Its through-hole package is easier to inspect, socket, and replace than a fine-pitch surface-mount equivalent. The familiar SN74LS390N designation also supports comparison with second-source documentation. During repair, verify that the replacement counter’s pinout, supply requirements, and timing specifications match the original assembly rather than relying only on the function description. Inspect nearby sockets for bent contacts and confirm that the clock source does not exceed the device’s specified operating frequency.
সুপারিশকৃত
সুপারিশকৃত পণ্যের সারসংক্ষেপ
এর জন্য ইঞ্জিনিয়ারিং রেফারেন্স ডেটা SN74LS390N — তুলনা, ডিজাইন গাইডেন্স এবং কমপ্লায়েন্স তথ্য।
নির্বাচন গাইড
বিকল্পের সাথে তুলনা
| পারামিটার | এই পণ্য | SN74LS390N | SN74LS390N | MC74HC390ANG |
|---|---|---|---|---|
| Manufacturer | Texas Instruments | Motorola | onsemi | onsemi |
| Package | 16-pin PDIP | 16-pin PDIP | 16-pin PDIP | 16-pin PDIP |
| Counter Function | Dual 4-bit decade counter | Dual 4-bit decade counter | Dual 4-bit decade counter | Dual 4-bit decade counter |
| Counter Elements | 2 elements | 2 elements | 2 elements | 2 elements |
| Bits per Counter | 4 bits | 4 bits | 4 bits | 4 bits |
| Logic Family | 74LS TTL | 74LS TTL | 74LS TTL | 74HC CMOS |
মূল পার্থক্যসমূহ
- Two decade counters in one package (বনামSN74LS390N)
- Direct same-family second-source options (বনামMC74HC390ANG)
- Negative-edge decade operation (বনামSN74LS393N)
ডিজাইন নোট
Route clock inputs away from switching nodes, relay drivers, and long parallel data paths. The counter advances on the specified clock edge, so ringing near that transition can create false counts. Use a short return path, a continuous ground plane, and source termination only when the source impedance and clock topology require it. For noisy industrial inputs, condition the signal with a Schmitt-trigger stage or other debouncing circuit before it reaches the counter.
Place the supply bypass capacitor close to the IC power pin and provide a low-impedance ground connection. Avoid routing the clock between split ground regions, and keep the counter away from high-current switching paths. For cascaded decimal counters, inspect the source-to-destination trace to ensure that adjacent clock edges do not violate the available timing margin. Through-hole DIP placement should also account for lead-ins, soldering clearance, and service access.
Do not treat a related 4-bit binary counter as a decade-counter replacement without adding decoding logic. Likewise, a CMOS HC counter is not electrically identical to a 74LS TTL counter even when both provide dual decade counting. Before substitution, compare pin names, supply voltage, input thresholds, output levels, clock edge, propagation delay, output current, and operating temperature. Also verify that unused inputs are brought to a defined level.
কমপ্লায়েন্স তথ্য
No specific RoHS, REACH, lead-free, halogen-free, or conflict-minerals statement is identified for the exact SN74LS390N ordering variant.