STM32F101ZCT6 - ARM Cortex-M3 MCU, 256KB Flash, 144-LQFP | STMicroelectronics
MPN: STM32F101ZCT6 ✓ সক্রিয়STM32F101ZCT6 সারাংশ
An ARM Cortex-M3 microcontroller is a 32-bit RISC processor core designed by Arm Holdings, featuring Thumb-2 instruction set, hardware single-precision multiply, and a Nested Vectored Interrupt Controller (NVIC). The STM32F101 family belongs to the broader STM32 ecosystem, which sits within the hierarchy: microcontroller -> embedded MCU -> semiconductor -> integrated circuit. Compared with the F0 (Cortex-M0) and F4 (Cortex-M4) families, the F1 family targets mainstream applications with low cost, simple peripherals, and broad tool support.
The device features 256 KB of single-bank Flash, 32 KB SRAM, up to 112 general-purpose I/O, three 12-bit ADCs (1 µs conversion), up to ten timers, USB full-speed device, two CAN 2.0B controllers, three USARTs, two SPIs, and two I²C buses. The integrated voltage regulator supports 2.0–3.6 V single-supply operation with brown-out reset and programmable voltage detector, allowing direct Li-ion or 3.3 V system-rail connection.
From an architectural standpoint, the STM32F101ZCT6 uses a 3-stage pipelined Cortex-M3 core with single-cycle multiplier and hardware divide (2–12 cycles). The bus matrix arbitrates between the CPU DMA core, Flash/7-three code, SRAM, and peripheral bridges (APB1/APB2). This multi-bus topology lets USB/CAN transfer work while the CPU executes from Flash without contention, simplifying firmware development.
Typical applications include industrial motor drives, USB HID peripherals, CAN-node industrial controllers, building automation gateways, HVAC controls, smart-metering nodes, and consumer appliances requiring moderate processing, mixed-signal performance, and abundant I/O.
A key design consideration: at 72 MHz operation, design PCB layout with 4-layer stack-up, decoupling capacitors placed within 5 mm of each supply pin, and crystal traces guarded by ground to meet USB and CAN EMC requirements. The 144-pin LQFP has generous ground pins for low-impedance return paths.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone, optimized for engineers searching for an STM32F101 access-line replacement or pin-compatible second source.
এর জন্য ড্রপ-ইন বিকল্প STM32F101ZCT6 — একই package, pin-to-pin compatible। ভিন্ন package-এর যেসব পার্টে PCB rework প্রয়োজন সেগুলো বাদ দেওয়া হয়েছে।
এই সিরিজের ভ্যারিয়েন্ট
একই সিরিজের মডেল যেগুলো drop-in compatible STM32F101ZCT6 (একই form factor এবং footprint) — পার্থক্য রয়েছে CAN, Communication Interfaces, Flash Memory, Operating Temperature, Package.
STM32F103ZCT6
✅ ড্রপ-ইনমূল্যের জন্য যোগাযোগ করুন
ডেটাশিট দেখুন →STM32F100ZCT6
✅ ড্রপ-ইন📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)
STM32F105ZCT6
✅ ড্রপ-ইন📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)
STM32F107ZCT6
✅ ড্রপ-ইন📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)
GD32F103ZCT6
✅ ড্রপ-ইন📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)
STM32F101ZCT6 সর্বোচ্চ রেটিং ও বৈদ্যুতিক বৈশিষ্ট্য
| Core Architecture | ARM Cortex-M3 32-bit RISC |
| Maximum CPU Clock | 36 MHz |
| Flash Memory | 256 KB |
| SRAM | 32 KB |
| প্যাকেজ | LQFP-144 (20x20 mm) |
| Supply Voltage Range | 2.0 V to 3.6 V |
| I/O Pins | 112 |
| ADC | 3x 12-bit, 1 µs conversion |
| USB | USB 2.0 Full-Speed Device |
| CAN | 2x CAN 2.0B active |
| Timers | Up to 10 (including advanced-control PWM) |
| Communication Interfaces | 3x USART, 2x SPI, 2x I²C |
| অপারেটিং তাপমাত্রা | -40 °C to +85 °C |
| RoHS স্ট্যাটাস | Compliant |
| মাউন্টিং টাইপ | Surface Mount |
STM32F101ZCT6 lqfp-144 (20x20 mm) পিন কনফিগারেশন গাইড
STM32F101ZCT6 (lqfp-144 (20x20 mm) প্যাকেজ)-এর পিন কনফিগারেশন। এই ডিজিটাল IC-তে GPIO, কমিউনিকেশন ইন্টারফেস (UART, SPI, I2C) এবং পাওয়ার পিন রয়েছে। বিকল্প পিন ফাংশন ও কনফিগারেশন অপশনের জন্য প্রস্তুতকারকের ডেটাশিট দেখুন। এমবেডেড সিস্টেম ডিজাইন ও PCB লেআউটের জন্য অপরিহার্য।
এর জন্য বিস্তারিত পিনআউট ডেটা পাওয়া যায়নি STM32F101ZCT6.
দেখুন ডেটাশিট সম্পূর্ণ পিন কনফিগারেশনের জন্য।
সাধারণ ব্যবহার
STM32F101ZCT6 এর জন্য উপযুক্ত 6 অ্যাপ্লিকেশনs: Industrial CAN-Bus Motor Controller, USB HID Peripheral / Data-Acquisition Device, Building Automation Gateway, Smart-Meter / Energy Monitor Node, Consumer Appliance Control Board, HVAC Climate-Control Module.
Industrial CAN-Bus Motor Controller
The STM32F101ZCT6's dual CAN 2.0B controllers and 12-bit ADC suite make it a strong fit for industrial motor drives. With 256 KB on-chip Flash and 32 KB SRAM, the device hosts CANopen or DeviceNet stacks without external memory. Its 10 timers include advanced-control PWM units needed for field-oriented control of three-phase BLDC or PMSM motors. The LQFP-144 footprint exposes up to 112 GPIO, sufficient for encoder, Hall-sensor, fault, and gate-driver interfaces. According to the STMicroelectronics datasheet, the F101 integrates two CAN controllers operating at 1 Mbaud, suiting distributed industrial networks.
সুপারিশকৃত
USB HID Peripheral / Data-Acquisition Device
With integrated USB 2.0 Full-Speed device (12 Mbps) and 256 KB Flash, the STM32F101ZCT6 fits USB HID peripherals such as custom keypads, jog-shuttles, and lab data-acquisition front-ends. The 36 MHz Cortex-M3 core sustains 12 Msps ADC aggregate throughput when paired with three independent 12-bit ADCs (1 µs conversion). USB peripheral library examples ship with STM32 firmware packages, cutting firmware-development time. The LQFP-144 package exposes ample GPIO for parallel sensor arrays, isolation barriers, and status LEDs without external glue logic.
সুপারিশকৃত
Building Automation Gateway
The STM32F101ZCT6 is well suited for building-automation gateways that bridge RS-485, KNX-style buses, and CAN. Its three USARTs and two I²C buses handle sensor and HVAC-panel peripherals concurrently, while CAN controllers carry high-speed backbone traffic. The 32 KB SRAM holds BACnet/Modbus stacks without external memory. Brown-out reset and programmable voltage detector ensure reliable operation on noisy 24 V industrial rails stepped down to 3.3 V.
সুপারিশকৃত
Smart-Meter / Energy Monitor Node
Energy-meter designs benefit from the STM32F101ZCT6's three 12-bit ADCs (1 µs each) that simultaneously sample voltage and current channels. With 256 KB Flash, the device hosts metrology algorithms, RMS calculations, and DLMS/COSEM protocol stacks. The integrated USB device enables field firmware-upgrades without external programmers. The 144-LQFP package handles optocoupler-isolated communication lines and tamper-detection inputs.
সুপারিশকৃত
Consumer Appliance Control Board
The STM32F101ZCT6 drives washing-machine, induction-cooktop, and dishwasher control boards thanks to its 10 timers (including advanced-control PWM), 12-bit ADC, and Cortex-M3 deterministic interrupt response. The 256 KB Flash accommodates display UI state machines plus motor-control libraries. The LQFP-144 footprint enables single-layer board layout for high-volume consumer products.
সুপারিশকৃত
HVAC Climate-Control Module
The STM32F101ZCT6 is a strong fit for HVAC climate-control modules requiring multiple temperature sensors (NTC), fan-speed control, and display interfacing. Two I²C buses drive temperature/humidity sensors and EEPROM, and three 12-bit ADCs digitise analog inputs in parallel for closed-loop fan control. The 36 MHz Cortex-M3 delivers real-time PID loop execution at 1 ms periods.
সুপারিশকৃত
সুপারিশকৃত পণ্যের সারসংক্ষেপ
এর জন্য ইঞ্জিনিয়ারিং রেফারেন্স ডেটা STM32F101ZCT6 — তুলনা, ডিজাইন গাইডেন্স এবং কমপ্লায়েন্স তথ্য।
নির্বাচন গাইড
বিকল্পের সাথে তুলনা
| পারামিটার | এই পণ্য | STM32F103ZCT6 | STM32F100ZCT6 | STM32F105ZCT6 | GD32F103ZCT6 |
|---|---|---|---|---|---|
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics | GigaDevice |
| Package | LQFP-144 | LQFP-144 (same) | LQFP-144 (same) | LQFP-144 (same) | LQFP-144 (same) |
| Core | Cortex-M3 36 MHz | Cortex-M3 72 MHz | Cortex-M3 24 MHz | Cortex-M3 72 MHz | Cortex-M3 108 MHz |
| Flash | 256 KB | 256 KB | 256 KB | 256 KB | 256 KB |
| SRAM | 32 KB | 48 KB | 24 KB | 64 KB | 48 KB |
| USB | USB FS Device | USB FS Device | None | USB OTG FS | USB FS Device |
| CAN | 2x CAN 2.0B | 1x CAN 2.0B | 1x CAN 2.0B | 2x CAN 2.0B | 1x CAN 2.0B |
| Ethernet MAC | No | No | No | No | Yes |
| Supply Voltage | 2.0 - 3.6 V | 2.0 - 3.6 V | 2.0 - 3.6 V | 2.0 - 3.6 V | 2.6 - 3.6 V |
মূল পার্থক্যসমূহ
- Dual integrated CAN 2.0B controllers in this density tier (বনামSTM32F103ZCT6)
- Cortex-M3 at 36 MHz with 256 KB Flash in the access line price tier (বনামGD32F103ZCT6)
- Active production status with broad second-source ecosystem (বনামSTM32L152ZCT6TR)
ডিজাইন নোট
The STM32F101ZCT6 has separate VDD/VDDA/VBAT pins. Decouple VDD pins with 100 nF ceramic capacitors placed within 5 mm of each pin, and add a single 4.7 µF bulk capacitor on each supply rail. According to STMicroelectronics application note AN2586, separate VDDA filtering with a ferrite bead reduces ADC noise by up to 2 LSB. Use a 2.2 µF capacitor on VREF+ if the ADC operates at full 1 Msps.
Route the 8 MHz HSE crystal traces symmetrically within a ground guard ring, keeping trace length under 5 mm. USB D+/D- traces must be 90 Ω differential with length matching within 2 mm. The LQFP-144 package has 22 ground pins; stitch them with vias to an internal ground plane for low-impedance return paths. Place decoupling capacitors on the opposite side of the PCB directly under their respective supply pins.
Do not drive the BOOT0 pin floating; tie it to ground via 10 kΩ for standard boot from Flash. Enable the integrated voltage regulator's power-on reset delay by connecting NRST to VDD through 10 kΩ with 100 nF to ground. The LQFP-144 footprint allows easy migration to STM32F103/F105/F107 family parts with no PCB changes, so design the application to needlessly inherit this forward compatibility.
Estimated: at maximum CPU activity (36 MHz, all peripherals enabled, 3.6 V supply), the STM32F101ZCT6 dissipates approximately 80 mA * 3.3 V ≈ 264 mW. The LQFP-144 with 22 thermal ground pins achieves θJA ≈ 35 °C/W on a 4-layer JEDEC test board, yielding a junction-to-ambient rise of ~9 °C. No heatsink needed for industrial -40 °C to +85 °C operation. Verify with thermal simulation if sealing the enclosure.
কমপ্লায়েন্স তথ্য
RoHS compliant per ST product page. Not AEC-Q100 qualified; not applicable for automotive safety-critical. Frees with IEMCG / EPU / ECCN EAR99 export classification.
