STM32G071CBU7 - 64MHz Cortex-M0+ MCU | STMicroelectronics
MPN: STM32G071CBU7 ✓ সক্রিয়STM32G071CBU7 সারাংশ
A microcontroller is a programmable semiconductor that combines a processor core with memory, peripherals, and interfaces on one integrated circuit. The STM32G0 family belongs to the Arm Cortex-M0+ microcontroller hierarchy, where the M0+ core combines an energy-efficient 32-bit architecture with deterministic real-time performance. This makes the STM32G071CBU7 appropriate for cost-sensitive embedded control, sensing, actuator control, and connected industrial equipment.
The principal features include a 64 MHz maximum CPU frequency, 128 KB of Flash for firmware, 36 KB of SRAM for working data, four USART peripherals, general-purpose timers, a 12-bit ADC, and a DAC. The 1.7 V to 3.6 V operating range supports low-voltage embedded systems, while the 48-UFQFPN package reduces board area compared with larger leaded microcontroller packages. The manufacturer identifies the STM32G071x8/xB devices as mainstream Cortex-M0+ products.
The Cortex-M0+ core uses a 32-bit RISC instruction set and supports operating frequencies up to 64 MHz. The integrated analog and communications resources allow a design to avoid separate ADC, DAC, and serial-interface components when their electrical and timing requirements match those of the STM32G071CBU7. Four USARTs support multiple serial links, while dedicated timers support periodic events, motor-control-related timing, or other waveform-generation tasks.
Typical applications include industrial sensor nodes, compact motor controllers, building automation modules, USB-connected peripheral controllers, battery-powered instruments, and general-purpose embedded control boards. The 7 x 7 mm package is particularly useful when board space is constrained, although the exposed-pad arrangement requires deliberate PCB thermal and assembly planning.
Power and layout begin with the 1.7 V to 3.6 V operating range. Confirm that every external peripheral and signal remains within the device's electrical limits before finalizing the schematic. Place the decoupling network close to the supply pins, preserve the package land pattern, and follow the manufacturer's pin, exposed-pad, and assembly guidance when laying out the PCB.
This product page combines the manufacturer's family-level technical information with procurement-oriented details and a strict same-footprint comparison. It distinguishes directly interchangeable STM32G071CB package variants by temperature grade, ordering suffix, and verified availability while making clear that cross-brand alternatives require separate hardware and firmware qualification.
এর জন্য ড্রপ-ইন বিকল্প STM32G071CBU7 — একই package, pin-to-pin compatible। ভিন্ন package-এর যেসব পার্টে PCB rework প্রয়োজন সেগুলো বাদ দেওয়া হয়েছে।
এই সিরিজের ভ্যারিয়েন্ট
একই সিরিজের মডেল যেগুলো drop-in compatible STM32G071CBU7 (একই form factor এবং footprint) — পার্থক্য রয়েছে Package, ADC, Flash Organization.
STM32G071CBU6
✅ ড্রপ-ইন ⚠️ স্পেক যাচাইকৃত নয়মূল্যের জন্য যোগাযোগ করুন
ডেটাশিট দেখুন →STM32G071CBT6
✅ ড্রপ-ইন ⚠️ স্পেক যাচাইকৃত নয়মূল্যের জন্য যোগাযোগ করুন
ডেটাশিট দেখুন →STM32G071CBT3TR
✅ ড্রপ-ইন📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)
STM32G071CBU7 সর্বোচ্চ রেটিং ও বৈদ্যুতিক বৈশিষ্ট্য
| Product Type | 32-bit Arm Cortex-M0+ microcontroller |
| Maximum CPU Frequency | 64 MHz |
| Core Architecture | Arm Cortex-M0+ 32-bit RISC |
| Flash Memory | 128 KB |
| RAM | 36 KB |
| অপারেটিং সাপ্লাই ভোল্টেজ | 1.7 V to 3.6 V |
| USART Count | 4 |
| ADC | 12-bit |
| DAC | Integrated |
| Timer Resources | Integrated timers |
| Communication Interfaces | Integrated communication interfaces |
| প্যাকেজ | 48-UFQFPN (7 x 7 mm) |
| পিন সংখ্যা | 48 pins |
| মাউন্টিং টাইপ | Surface mount |
STM32G071CBU7 48-ufqfpn (7 x 7 mm) পিন কনফিগারেশন গাইড
STM32G071CBU7 (48-ufqfpn (7 x 7 mm) প্যাকেজ)-এর পিন কনফিগারেশন। এই ডিজিটাল IC-তে GPIO, কমিউনিকেশন ইন্টারফেস (UART, SPI, I2C) এবং পাওয়ার পিন রয়েছে। বিকল্প পিন ফাংশন ও কনফিগারেশন অপশনের জন্য প্রস্তুতকারকের ডেটাশিট দেখুন। এমবেডেড সিস্টেম ডিজাইন ও PCB লেআউটের জন্য অপরিহার্য।
এর জন্য বিস্তারিত পিনআউট ডেটা পাওয়া যায়নি STM32G071CBU7.
দেখুন ডেটাশিট সম্পূর্ণ পিন কনফিগারেশনের জন্য।
সাধারণ ব্যবহার
STM32G071CBU7 এর জন্য উপযুক্ত 6 অ্যাপ্লিকেশনs: Industrial Sensor Node, Compact Motor Controller, USB Communication Peripheral, Battery-Powered Instrument, Building Automation Module, General Embedded Control Board.
Industrial Sensor Node
The STM32G071CBU7 fits industrial sensor nodes that combine periodic analog measurement with local filtering, diagnostics, and serial data transfer. Its 12-bit ADC supports analog sensing, while the 64 MHz Cortex-M0+ core provides capacity for protocol handling and control logic without requiring a higher-performance processor. Four USARTs allow concurrent use for an external transceiver, local console, or service interface. The 128 KB Flash and 36 KB RAM provide room for application firmware and working buffers. Confirm the final enclosure temperature and supply range against the device's ordering-grade limits before deployment.
Compact Motor Controller
The STM32G071CBU7 is suitable for compact motor-control and actuator-control modules where deterministic timing, analog feedback, and limited board area are important. Its integrated timers support periodic counting, PWM generation, and input capture, while the ADC can monitor current, position, or temperature feedback. The 64 MHz Cortex-M0+ core can execute proportional, integral, derivative, or other real-time control loops. The 48-UFQFPN package reduces PCB footprint, but the exposed-pad connection and copper heat-spreading area must follow the manufacturer's package guidance to maintain reliable performance.
USB Communication Peripheral
The STM32G071CBU7 can serve as the control device in a compact USB communication peripheral when the design requires local enumeration, data handling, and configuration storage. The 64 MHz Cortex-M0+ processor and 36 KB of RAM are suitable for moderate protocol processing, while 128 KB of Flash accommodates device firmware and configuration logic. Integrated timers and four USARTs support auxiliary status, control, or legacy serial channels. Designers should allocate USB data-path routing carefully in the dense 48-pin package and verify all high-speed signal-routing and impedance requirements against the relevant hardware guidelines.
Battery-Powered Instrument
The STM32G071CBU7 fits low-power battery-powered instruments that combine sensing, local display or actuator control, and intermittent communications. Its 1.7 V to 3.6 V operating range supports low-voltage supply architectures, and low-power microcontroller operating modes can reduce energy use between measurements. The ADC and DAC support analog measurement or bias generation, while four USARTs provide flexible sensor and host connectivity. With 128 KB of Flash and 36 KB of RAM, the device can handle moderate data acquisition and protocol tasks. Final battery-life calculations should include regulator quiescent current, wake-up behavior, and radio load transients.
Building Automation Module
The STM32G071CBU7 is appropriate for compact building-automation modules that monitor environmental inputs and control lighting, HVAC interfaces, or motorized equipment. The integrated ADC handles analog sensors, four USARTs support local bus or gateway connectivity, and the timers assist with periodic sampling and actuator timing. The 48-UFQFPN package minimizes board area in distributed control boxes, while 128 KB of Flash and 36 KB of RAM are sufficient for several embedded communication and control tasks. Verify the operating-temperature grade, isolation strategy, and interface surge requirements before installing the module in a building environment.
General Embedded Control Board
The STM32G071CBU7 is a versatile choice for general embedded-control boards requiring more processing and peripheral integration than an 8-bit controller but less complexity than a high-end microcontroller. Its 64 MHz Cortex-M0+ core handles real-time tasks, the 12-bit ADC and DAC provide mixed-signal capability, and four USARTs simplify multi-channel connectivity. The 128 KB Flash and 36 KB of RAM support moderate firmware, protocol, and logging workloads. The compact 48-UFQFPN land pattern can reduce board area, although assembly and prototype access should be considered because the fine-pitch package is less convenient for manual rework.
এর জন্য ইঞ্জিনিয়ারিং রেফারেন্স ডেটা STM32G071CBU7 — তুলনা, ডিজাইন গাইডেন্স এবং কমপ্লায়েন্স তথ্য।
নির্বাচন গাইড
বিকল্পের সাথে তুলনা
| পারামিটার | এই পণ্য | STM32G071CBU6 | STM32G071CBT6 | STM32G071CBT3TR |
|---|---|---|---|---|
| Package | 48-UFQFPN (7 x 7 mm) | 48-UFQFPN (7 x 7 mm) | 48-UFQFPN (7 x 7 mm) | 48-UFQFPN (7 x 7 mm) |
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics |
| CPU Core | Arm Cortex-M0+ 32-bit RISC | Arm Cortex-M0+ 32-bit RISC | Arm Cortex-M0+ 32-bit RISC | Arm Cortex-M0+ 32-bit RISC |
| Maximum CPU Frequency | 64 MHz | 64 MHz | 64 MHz | 64 MHz |
| Flash Memory | 128 KB | 128 KB | 128 KB | 128 KB |
| RAM | 36 KB | 36 KB | 36 KB | 36 KB |
| Operating Supply Voltage | 1.7 V to 3.6 V | 1.7 V to 3.6 V | 1.7 V to 3.6 V | 1.7 V to 3.6 V |
| Ordering and Packing Suffix | U7 | U6 | T6 | T3TR |
| USART Count | 4 | 4 | 4 | 4 |
| ADC Resolution | 12-bit | 12-bit | 12-bit | 12-bit |
| DAC | Integrated | Integrated | Integrated | Integrated |
মূল পার্থক্যসমূহ
- Higher-ordering-suffix temperature option (বনামSTM32G071CBU6)
- Full 48-pin peripheral integration in a compact package (বনামSTM32G071CBT3TR)
- Mainstream Cortex-M0+ performance (বনামSTM32G071CBU6)
ডিজাইন নোট
Use the manufacturer's 48-UFQFPN land pattern and exposed-pad connection exactly as specified. Place the device-side input and output capacitors close to their corresponding pins, keep the power loop compact, and avoid routing fast or sensitive signals beneath the exposed-pad area unless the layer stackup expressly supports it. Verify the final footprint against the ordering code and assembly process because exposed-pad geometry is critical to solderability and thermal performance.
Design the 1.7 V to 3.6 V supply for both average load and startup transients. Use the datasheet's recommended capacitor values and voltage ratings, account for regulator tolerance and dynamic resistance, and confirm that the MCU rail does not cross an absolute maximum limit during brownout or peripheral startup. If the board includes USB or another high-current load, isolate that load from the MCU rail to prevent shared impedance from disturbing ADC, DAC, and communications performance.
The 48-UFQFPN package relies on its exposed thermal pad and surrounding PCB copper for heat spreading. Provide a continuous copper connection beneath the pad, attach thermal vias according to the manufacturer's assembly guidance, and keep them clear of tenting or plating changes that could interfere with solder filling. A thermal calculation is unnecessary until actual dissipation, ambient temperature, and board construction are known; evaluate the final assembly at the highest expected operating temperature.
Keep analog inputs, DAC outputs, oscillator connections, and communication lines away from high-current switching nodes. Route sensitive analog traces over a continuous reference plane where practical, minimize loop area around ADC inputs, and place anti-alias or filtering components close to the source. Four USARTs can simplify connectivity, but each interface should use the pin-multiplexing and alternate-function settings defined for the STM32G071CB package.
Do not treat a shared package footprint as proof that every ordering suffix is interchangeable. Before substituting STM32G071CBU6, STM32G071CBT6, or STM32G071CBT3TR, compare temperature grade, tape-and-reel orientation, exposed-pad construction, and the manufacturer's ordering-information table. Also preserve the exact boot, clock, and peripheral configuration when changing parts because suffix changes can coexist with qualification and lifecycle differences.
কমপ্লায়েন্স তথ্য
The manufacturer product description and distributor listings do not explicitly establish the requested compliance statuses for STM32G071CBU7. Confirm RoHS, REACH, automotive qualification, lead-free, halogen-free, and conflict-minerals declarations using the exact ordering code.