TJA1027T/20/1J - 20 kBd LIN 2.2A Transceiver | NXP
MPN: TJA1027T/20/1J ✓ সক্রিয়TJA1027T/20/1J সারাংশ
A LIN transceiver is the physical-layer interface between a microcontroller-based LIN node controller and the wired LIN bus. It converts controller transmit commands into a shaped bus signal, receives bus states for the controller, and provides the voltage translation and bus termination needed in an automotive low-speed serial network. The TJA1027 belongs to the interface IC and automotive communication transceiver hierarchy.
The TJA1027T/20/1J supports LIN 2.0 through LIN 2.2A operation and SAE J2602 network requirements. Its transmit path creates an optimized LIN waveform intended to minimize electromagnetic emissions, while the LIN bus output is pulled high through an internal termination resistor. The 20 kBd operating rate supports typical in-vehicle LIN sub-networks rather than high-speed communication links.
NXP identifies the TJA1027 as pin-compatible with the TJA1020 and TJA1021, and the broader datasheet compatibility statement also identifies TJA1022 and TJA1029 compatibility. Its 8-pin SOIC package supports conventional surface-mount assembly, while the automotive qualification designation supports use in vehicle electronic control units when the complete system requirements call for an automotive-grade component.
Typical applications include LIN-controlled vehicle body modules, seat and door controllers, climate-control panels, switch-bank electronics, ambient-light sensors, and other low-speed vehicle sub-networks. In each case, the transceiver provides the physical bus interface while a separate LIN protocol controller or LIN-capable microcontroller handles frames, scheduling, diagnostics, and higher-layer communication.
Designers should account for the transceiver and controller supply domains, LIN bus pull-up resistance, ground reference quality, waveform timing, EMC layout, and unused-pin treatment. The 5 V to 18 V operating range does not remove the need to protect the LIN line against automotive transients; the bus network must be evaluated using the application’s voltage, ground-offset, slew-rate, and fault-recovery requirements.
This product page combines NXP protocol and compatibility information with package-focused alternatives, selection guidance, and implementation considerations. It distinguishes true pin-compatible options from merely similar LIN devices and highlights the operating conditions that should be checked before replacing an existing TJA1027 implementation.
এর জন্য ড্রপ-ইন বিকল্প TJA1027T/20/1J — একই package, pin-to-pin compatible। ভিন্ন package-এর যেসব পার্টে PCB rework প্রয়োজন সেগুলো বাদ দেওয়া হয়েছে।
এই সিরিজের ভ্যারিয়েন্ট
একই সিরিজের মডেল যেগুলো drop-in compatible TJA1027T/20/1J (একই form factor এবং footprint) — পার্থক্য রয়েছে Package, Product Type, Maximum Baud Rate, Pin Compatibility, Pin Count.
TJA1020
✅ ড্রপ-ইন ⚠️ স্পেক যাচাইকৃত নয়📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)
TJA1021T/20/C
✅ ড্রপ-ইন ⚠️ স্পেক যাচাইকৃত নয়মূল্যের জন্য যোগাযোগ করুন
ডেটাশিট দেখুন →TJA1022TK
✅ ড্রপ-ইন ⚠️ স্পেক যাচাইকৃত নয়মূল্যের জন্য যোগাযোগ করুন
ডেটাশিট দেখুন →TJA1029T/2Z
✅ ড্রপ-ইনমূল্যের জন্য যোগাযোগ করুন
ডেটাশিট দেখুন →TJA1028T/5V0/10/2Z
✅ ড্রপ-ইন📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)
TJA1027T/20/1J বিশেষণ
| Product Type | Single-channel LIN bus transceiver |
| LIN Bus Configuration | 1/1 half-duplex transceiver |
| Maximum LIN Baud Rate | 20 kBd |
| Supply Voltage Range | 5 V to 18 V |
| LIN 2.0 Compliance | Compliant |
| LIN 2.1 Compliance | Compliant |
| LIN 2.2 Compliance | Compliant |
| LIN 2.2A Compliance | Compliant |
| SAE J2602 Compliance | Compliant |
| ISO 17987-4:2016 | Compliant for 12 V |
| Automotive Qualification | AEC-Q100 |
| প্যাকেজ | 8-pin SOIC |
| Package Type | SOIC-8 |
| মাউন্টিং টাইপ | Surface mount |
| Internal LIN Termination | Pull-up through internal termination resistor |
| Transmit Waveform | Optimized LIN bus signal for minimized electromagnetic emissions |
| Compatible NXP Families | TJA1020, TJA1021, TJA1022 and TJA1029 |
TJA1027T/20/1J soic-8 পিন কনফিগারেশন গাইড
TJA1027T/20/1J (soic-8 প্যাকেজ)-এর পিন কনফিগারেশন। পিন নম্বরিং, ফাংশন এবং সংযোগ ডায়াগ্রাম প্রস্তুতকারকের ডেটাশিটে সংজ্ঞায়িত করা আছে। সঠিক ফুটপ্রিন্ট এবং সোল্ডারিং নির্দেশিকার জন্য এটি দেখুন।
এর জন্য বিস্তারিত পিনআউট ডেটা পাওয়া যায়নি TJA1027T/20/1J.
দেখুন ডেটাশিট সম্পূর্ণ পিন কনফিগারেশনের জন্য।
সাধারণ ব্যবহার
TJA1027T/20/1J এর জন্য উপযুক্ত 6 অ্যাপ্লিকেশনs: Vehicle Door Control Module, Automotive Climate-Control Panel, Seat Adjustment Controller, Automotive Switch Bank, Ambient-Light Sensor Node, Body Control Module.
Vehicle Door Control Module
The TJA1027T/20/1J fits a LIN door-control node that operates a lock, window switch or latch actuator. Its 20 kBd LIN rate matches the speed class used by automotive LIN sub-networks, while LIN 2.2A and SAE J2602 compliance provides protocol and qualification support for vehicle applications. The 5 V to 18 V transceiver supply range allows the interface to operate from a vehicle-compatible supply domain, subject to module-level transient protection. Place the transceiver beside the LIN bus connector, provide a low-impedance ground return, and route the LIN output away from sensitive sensor and actuator-control traces to limit electromagnetic coupling.
সুপারিশকৃত
Automotive Climate-Control Panel
The TJA1027T/20/1J is suitable for a climate-control panel that connects button inputs, a display controller and motorized vents over a LIN sub-network. Its 20 kBd communication rate is appropriate for the low-bandwidth command traffic typical of LIN, and its optimized transmit waveform is intended to minimize electromagnetic emissions in a densely packaged passenger compartment. The 8-pin SOIC format simplifies integration beside a LIN-capable microcontroller. Keep the controller interface short, maintain a common ground between the transceiver and processor, and follow the manufacturer bus recommendations when selecting the external pull-up and protection network.
সুপারিশকৃত
Seat Adjustment Controller
A seat adjustment controller can use the TJA1027T/20/1J to connect motor-position sensors and adjustment switches through a LIN network. The 20 kBd rate is appropriate for command and status traffic that does not require a high-speed automotive bus, while the transceiver’s 5 V to 18 V operating range supports integration into vehicle electronic modules. Its internally terminated high-side LIN output and emission-shaped transmit waveform support predictable bus behavior. Engineers should verify external pull-up resistance, fault recovery and ground offsets, and should provide suitable protection for any switch or motor circuitry connected outside the LIN bus.
সুপারিশকৃত
Automotive Switch Bank
The TJA1027T/20/1J can interface a distributed switch bank containing window, lighting or HVAC switches with a central body controller. LIN’s single-wire communication reduces wiring complexity in vehicle sub-networks, and the transceiver supports up to 20 kBd with LIN 2.2A and SAE J2602 compatibility. The 8-pin SOIC package permits conventional PCB routing between the logic controller and bus connector. Preserve controlled bus rise and fall behavior by following the manufacturer’s pull-up and capacitance guidance, and locate protection components where they can clamp connector-borne transients without degrading the LIN waveform.
সুপারিশকৃত
Ambient-Light Sensor Node
The TJA1027T/20/1J is appropriate for an ambient-light sensor node that reports measurements and operating status to a vehicle controller through LIN. The 20 kBd bus rate supports the limited data volume of a sensor node, while the dedicated transceiver provides a clearer physical separation between the controller logic and the bus waveform. The optimized transmission waveform helps reduce electromagnetic emissions in a compact sensor housing. Use a low-inductance ground connection, keep the LIN trace short, avoid placing high-current switching paths beside the bus, and confirm that the module’s supply and protection design remains compatible with the 5 V to 18 V transceiver range.
সুপারিশকৃত
Body Control Module
The TJA1027T/20/1J can serve as a LIN interface within a body control module connected to distributed automotive loads. Its support for LIN 2.0 through LIN 2.2A and SAE J2602 makes it appropriate for modern in-vehicle LIN sub-networks operating at up to 20 kBd. The 5 V to 18 V operating range is useful in vehicle electronics, while the 8-pin SOIC package keeps the footprint compact for multi-function control boards. Validate the full network’s pull-up configuration, bus capacitance, fault behavior and EMC performance, and ensure the transceiver ground is referenced cleanly to the controller and vehicle ground network.
সুপারিশকৃত
এর জন্য ইঞ্জিনিয়ারিং রেফারেন্স ডেটা TJA1027T/20/1J — তুলনা, ডিজাইন গাইডেন্স এবং কমপ্লায়েন্স তথ্য।
নির্বাচন গাইড
বিকল্পের সাথে তুলনা
| পারামিটার | এই পণ্য | TJA1020 | TJA1021 | TJA1022 | TJA1029 | TJA1028T/5V0/10/2Z |
|---|---|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | SOIC-8 | SOIC-8 | SOIC-8 | SOIC-8 | SOIC-8 | SOIC-8 |
| Product Type | Single-channel LIN bus transceiver | LIN transceiver | LIN transceiver | LIN transceiver | LIN transceiver | LIN transceiver |
| Maximum LIN Baud Rate | 20 kBd | 20 kBd | 20 kBd | 20 kBd | 20 kBd | 20 kBd |
মূল পার্থক্যসমূহ
- Documented modern LIN and SAE compatibility (বনামTJA1020)
- Explicit pin compatibility with established TJA102x families (বনামTJA1021)
- Common 20 kBd operating class (বনামTJA1029)
- Same 8-pin SOIC footprint across the documented alternative set (বনামTJA1022)
ডিজাইন নোট
Place the TJA1027T/20/1J near the LIN connector or transceiver interface and keep the LIN trace short. Provide a low-impedance ground connection between the transceiver ground, LIN-capable controller and vehicle ground network. Avoid routing the bus beside high-current motor, relay or switching-supply traces, and keep protection components close to connector entry so that their capacitance and inductance do not distort the nominal 20 kBd LIN waveform.
Use the optimized transmit path only with the bus pull-up and network capacitance specified by NXP. Verify the rise-time behavior across minimum and maximum bus lengths because excessive capacitance can slow edges and contribute to EMC failures. Maintain a symmetrical ground reference and use a continuous ground plane or equivalent low-impedance return path. EMC validation should be performed with the final harness, connector, module enclosure and neighboring loads rather than only on the bare PCB.
Do not treat package compatibility as proof that every LIN transceiver feature is identical. Before replacing the TJA1027T/20/1J, compare the exact alternative’s supply range, protocol revisions, controller-interface behavior, sleep current, wake-up operation, bus fault recovery and temperature grade. The target supports LIN 2.2A, SAE J2602 and ISO 17987-4:2016 for 12 V, so a substitute that does not satisfy the applicable vehicle network requirement may still require board or firmware changes.
The transceiver operates from a 5 V to 18 V supply, but the complete automotive module may also require reverse-battery, load-dump and transient protection. Separate the protected vehicle input from the transceiver supply and ensure that voltage at the IC remains within its limits during all specified vehicle conditions. Confirm controller and transceiver logic levels, enable polarity and timing in the system power-up sequence to prevent unintended bus states during reset.
কমপ্লায়েন্স তথ্য
The distributor listing identifies the TJA1027T/20/1J as automotive AEC-Q100. The manufacturer datasheet confirms LIN 2.0, LIN 2.1, LIN 2.2, LIN 2.2A, SAE J2602 and ISO 17987-4:2016 for 12 V. RoHS, REACH, lead-free, halogen-free and conflict-minerals status were not stated for the exact ordering code and remain unknown.