TJA1028T/3V3/10 - 3.3V LIN Transceiver with 70mA Regulator
MPN: TJA1028T/3V3/10 ✓ সক্রিয়TJA1028T/3V3/10 সারাংশ
A LIN transceiver is a physical-layer interface for the Local Interconnect Network, a low-cost, single-wire serial bus commonly used to connect sensors, actuators, door modules, climate controls, and other distributed automotive electronics. The TJA1028 combines that bus interface with a 3.3 V regulator, reducing the number of components required at a compact LIN slave node.
The headline features are compliance with LIN 2.0, LIN 2.1, SAE J2602, and ISO 17987-4:2016, a regulated 3.3 V output rated to 70 mA, and an 8-pin SOIC package. The integrated regulator allows a peripheral device to receive local supply from the LIN system while the transceiver communicates over the same harness.
The TJA1028 family is designed for compact nodes connected to 12 V LIN networks. Its integrated regulator supports the 3.3 V variant identified by the /3V3 ordering code, while the TJA1028 family also includes a 5.0 V regulator variant. This distinction is important because replacing the 3.3 V device with the 5.0 V device changes the local supply presented to attached circuitry.
Typical uses include LIN-connected sensor modules, body-control submodules, automotive door and seat electronics, climate-control nodes, and industrial control modules that use LIN for inexpensive short-range networking. Compactness and local supply integration are particularly valuable when the node must fit behind a vehicle trim panel or within a sealed enclosure.
When designing a TJA1028T/3V3/10 circuit, follow the NXP datasheet wiring and decoupling recommendations, preserve the transceiver's LIN bus and ground connections, and validate the regulator load transient response at the maximum 70 mA operating point. Check the package pin assignments against the selected PCB footprint before layout.
This product overview consolidates the manufacturer-defined LIN compliance, integrated 3.3 V regulator capability, package information, sourcing guidance, and engineering considerations into one reference for compact LIN-node development.
এর জন্য ড্রপ-ইন বিকল্প TJA1028T/3V3/10 — একই package, pin-to-pin compatible। ভিন্ন package-এর যেসব পার্টে PCB rework প্রয়োজন সেগুলো বাদ দেওয়া হয়েছে।
TJA1028T/5V/10
✅ ড্রপ-ইন ⚠️ স্পেক যাচাইকৃত নয়📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)
TJA1028T/3V3/10 বিশেষণ
| Product Type | LIN transceiver with integrated voltage regulator |
| LIN Standard Compliance | LIN 2.0 |
| LIN Standard Compliance | LIN 2.1 |
| Automotive LIN Compliance | SAE J2602 |
| LIN Compliance | ISO 17987-4:2016 (12 V) |
| Integrated Regulator Output | 3.3 V |
| Integrated Regulator Maximum Current | 70 mA |
| Bus Type | LIN single-wire bus |
| System Supply Class | 12 V |
| প্যাকেজ | 8-pin SOIC |
| মাউন্টিং টাইপ | Surface mount |
| Automotive Qualification | AEC-Q100 |
| Supplier Packaging | Tube |
TJA1028T/3V3/10 8-pin soic পিন কনফিগারেশন গাইড
TJA1028T/3V3/10 (8-pin soic প্যাকেজ)-এর পিন কনফিগারেশন। পিন নম্বরিং, ফাংশন এবং সংযোগ ডায়াগ্রাম প্রস্তুতকারকের ডেটাশিটে সংজ্ঞায়িত করা আছে। সঠিক ফুটপ্রিন্ট এবং সোল্ডারিং নির্দেশিকার জন্য এটি দেখুন।
এর জন্য বিস্তারিত পিনআউট ডেটা পাওয়া যায়নি TJA1028T/3V3/10.
দেখুন ডেটাশিট সম্পূর্ণ পিন কনফিগারেশনের জন্য।
সাধারণ ব্যবহার
TJA1028T/3V3/10 এর জন্য উপযুক্ত 6 অ্যাপ্লিকেশনs: Automotive LIN Sensor Node, Automotive Door Control Module, Climate-Control Peripheral, Seat and Switch Module, Industrial LIN Control Node, Compact Body-Control Submodule.
Automotive LIN Sensor Node
The TJA1028T/3V3/10 fits a compact automotive LIN sensor node where the harness can provide both communication and local power. Its integrated 3.3 V regulator supplies up to 70 mA, reducing the component count required for a 3.3 V sensor interface. According to the NXP manufacturer datasheet, the transceiver supports LIN 2.0, LIN 2.1, SAE J2602, and ISO 17987-4:2016 for 12 V systems. Place the device near the connector and route the LIN line according to the datasheet application circuit, while keeping sensitive sensor returns away from the bus connection.
Automotive Door Control Module
A door control module can use the TJA1028T/3V3/10 as both its LIN physical-layer interface and local 3.3 V supply source. The integrated regulator delivers up to 70 mA, which suits distributed low-power control electronics positioned behind a vehicle trim panel. The device's LIN 2.0, LIN 2.1, SAE J2602, and ISO 17987-4:2016 compliance supports use in a standardized 12 V network. Compact SOIC construction also helps constrain PCB area when the module must accommodate several other automotive functions.
Climate-Control Peripheral
The TJA1028T/3V3/10 is suitable for a small climate-control peripheral connected to a LIN master. Its 3.3 V regulator provides up to 70 mA for local logic or sensing circuitry, while the transceiver handles the single-wire bus connection. According to the NXP manufacturer datasheet, the device meets LIN 2.0 and LIN 2.1 requirements and applicable SAE J2602 and ISO 17987-4:2016 specifications. The main design consideration is to keep regulator load transients and LIN routing from disturbing adjacent low-level sensor signals.
Seat and Switch Module
A LIN-connected seat switch or occupancy module can combine bus communication with a local 3.3 V rail using the TJA1028T/3V3/10. The 70 mA regulator capability supports low-power switches, indicator electronics, or sensing circuitry without requiring a separate regulator package. According to the NXP manufacturer product page, the device supports LIN 2.0, LIN 2.1, SAE J2602, and ISO 17987-4:2016 for 12 V systems. Its 8-pin SOIC package simplifies placement in compact modules and minimizes board area around the harness connector.
Industrial LIN Control Node
The TJA1028T/3V3/10 can be used in an industrial LIN control node that requires a standardized single-wire interface and a local 3.3 V supply. The integrated regulator provides up to 70 mA for controller-side circuitry, while the LIN interface reduces the wiring needed between distributed modules. According to the NXP manufacturer datasheet, the transceiver is compliant with LIN 2.0, LIN 2.1, SAE J2602, and ISO 17987-4:2016 for 12 V applications. Validate the complete node against its environmental noise, grounding, and transient requirements.
Compact Body-Control Submodule
The TJA1028T/3V3/10 is useful for a compact body-control submodule with a LIN uplink and limited board space. Integrating the 3.3 V regulator beside the bus transceiver reduces the number of discrete power-supply components and supports loads up to 70 mA. According to the NXP manufacturer datasheet, the device supports LIN 2.0, LIN 2.1, SAE J2602, and ISO 17987-4:2016 for 12 V systems. Follow the recommended application-circuit layout and provide the regulator's required input and output capacitance close to the device.
এর জন্য ইঞ্জিনিয়ারিং রেফারেন্স ডেটা TJA1028T/3V3/10 — তুলনা, ডিজাইন গাইডেন্স এবং কমপ্লায়েন্স তথ্য।
নির্বাচন গাইড
বিকল্পের সাথে তুলনা
| পারামিটার | এই পণ্য | TJA1028T/5V/10 |
|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors |
| Package | 8-pin SOIC | 8-pin SOIC |
| Integrated Regulator Output | 3.3 V | 5.0 V |
| Regulator Output Current | 70 mA | 70 mA |
| LIN Compliance | LIN 2.0 and LIN 2.1 | LIN 2.0 and LIN 2.1 |
| SAE J2602 Compliance | Compliant | Compliant |
| ISO 17987-4:2016 Compliance | Compliant for 12 V | Compliant for 12 V |
| Automotive Qualification | AEC-Q100 | AEC-Q100 |
| Bus Type | LIN single-wire bus | LIN single-wire bus |
| Supply Class | 12 V system | 12 V system |
মূল পার্থক্যসমূহ
- Provides the required 3.3 V local rail (বনামTJA1028T/5V/10)
- Combines LIN communication and local power (বনামDiscrete LIN transceiver and regulator)
- Supports standardized automotive LIN operation (বনামNon-compliant generic LIN interface)
ডিজাইন নোট
Place the LIN transceiver and regulator decoupling components close to their corresponding pins, and route the LIN connection away from sensitive analog or high-speed digital traces. The NXP application circuit is the appropriate starting point for the input, output, and bus component arrangement. Keep the ground return continuous and avoid introducing long shared paths between LIN return currents and sensitive sensor ground.
Estimated regulator dissipation with a 12 V input, 3.3 V output, and 70 mA load is 0.609 W using the calculation P = (VIN - VOUT) × IOUT. Verify this estimate against the actual input voltage, load, and the regulator's maximum thermal limits. Provide adequate copper area around the 8-pin SOIC and avoid placing heat-generating components immediately beside it when the module operates at the maximum regulator current.
Do not substitute the 5.0 V TJA1028 variant for the 3.3 V device without checking every downstream rail and logic input. The regulator-output change from 3.3 V to 5.0 V is 51.5%, which can exceed the absolute maximum rating of a 3.3 V-only peripheral. Also verify the exact order code, tube packaging, pin assignments, and external-component values against the manufacturer datasheet.
Route the LIN bus as a controlled, single-wire network and minimize stubs from the transceiver to the harness connector. Keep the LIN trace away from switching nodes, high-current return paths, and crystal or sensor inputs. The manufacturer's bus application information should be used to select termination, pull-up, and protection components rather than relying on generic bus-layout rules.
কমপ্লায়েন্স তথ্য
AEC-Q100 qualification and LIN 2.0, LIN 2.1, SAE J2602, and ISO 17987-4:2016 compliance are identified for the TJA1028 family. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status were not established.