Products (44,000+)

TCA5013ZAHR - Smart Card Interface | Texas Instruments
TCA5013ZAHR

TCA5013ZAHR - Smart Card Interface | Texas Instruments

The Texas Instruments TCA5013ZAHR is a smart card interface IC designed for one user card and up to three Secure Access Module (SAM) cards. The device operates from a single supply, generates the required card voltages, and supports ISO 7816-3 and ISO 7816-10 compliant cards for point-of-sale terminals and other secure-access systems. It is packaged in a 48-pin NFBGA (ZAH) package measuring 5 x 5 mm. A smart card interface IC is an interface-controller device that connects a host processor with ISO 7816 smart cards and SAMs. It manages card power, card-clock and card-data signaling, card insertion detection, and the host-side control interface. The TCA5013 is intended for systems requiring one user-card slot plus multiple SAM sockets, allowing payment terminals and access-control products to share a controlled smart-card subsystem. The TCA5013 supports EMV 4.3, ISO 7816-3 and ISO 7816-10 applications. Its single-supply architecture reduces the number of external card-voltage rails required by the host design. The device also includes an I2C control interface and is designed to operate in the industrial temperature range from -40 °C to 85 °C. The 48-terminal NFBGA package provides a compact surface-mount solution for space-constrained terminal hardware. The manufacturer describes the TCA5013 as a feature-rich smartcard interface IC for payment-terminal designs. A typical implementation places the TCA5013 between the host controller and one user-card connector, with additional connectors for as many as three SAM cards. Card insertion and removal can be detected, while the IC controls the card interfaces and generates the card voltages required by the attached cards. The host configures the device through I2C rather than reproducing low-level card timing and power management in application firmware. The TCA5013 is suitable for electronic point-of-sale terminals, payment acceptance equipment, secure-access readers, banking terminals, and other ISO 7816-based systems. The TIDA-00382 reference design provides an implementation pattern for an electronic point-of-sale smart-card subsystem, including a user-card slot and TCA5013-based card detection. It is also useful where multiple secure credentials must be evaluated while maintaining a compact board footprint. PCB implementation requires careful BGA escape routing and power-supply integrity. Place the device close to the user-card and SAM connectors to minimize clock and data trace lengths, route sensitive signals away from switching nodes, and follow the manufacturer’s NFBGA land pattern and assembly guidance. Confirm the card connector pin assignments, pull-up requirements, supply capacitance, and signal-level compatibility before releasing the layout. This product page combines the manufacturer’s smart-card interface specifications with package and ordering details, application guidance, practical PCB considerations, and verified sourcing information. It is intended to help engineers identify the correct TCA5013ZAHR configuration and determine whether its 48-pin NFBGA implementation fits a given secure-card terminal design.

RFQ Contact
TCA5405RUGR - 5-Bit 1-Wire I/O Expander | Texas Instruments
TCA5405RUGR

TCA5405RUGR - 5-Bit 1-Wire I/O Expander | Texas Instruments

The Texas Instruments TCA5405RUGR is a 5-bit, self-timed, single-wire output expander with a 1.65 V to 3.6 V supply range, eight pins, and a compact 1.5 mm × 1.5 mm X2QFN RUG package. It is designed to add five controlled outputs to a portable embedded system while requiring only one communication line from the master device. The low-voltage operating range makes the device especially suitable for battery-powered and low-voltage mobile equipment. An output expander is an interface IC that increases the number of controllable outputs available from a microcontroller or other host device. The TCA5405 belongs to the I/O expander hierarchy, where a serial data input causes a group of output channels to change state according to a timing-controlled protocol. Unlike a conventional parallel GPIO port, this device uses a self-timed serial protocol synchronized to an internal clock, reducing the number of host interface signals required. The primary features of the TCA5405RUGR include five output channels, a wide 1.65 V to 3.6 V VCC operating range, a single-wire input, and a self-timed serial data protocol. Its 0.5 mm terminal pitch and 1.5 mm × 1.5 mm body support compact PCB layouts. The manufacturer specifies an operating temperature range of -40°C to +85°C, making the device suitable for industrial and extended-temperature portable applications when the surrounding system meets its electrical and mechanical requirements. In operation, the master device establishes the bit period during a Setup phase. The TCA5405 then uses that timing information to control the five outputs without requiring a separate clock line. This self-timed architecture simplifies connections in space-constrained systems, although the host firmware must generate the required waveform accurately. The protocol timing, output behavior, and electrical limits should be implemented according to the timing diagrams in the Texas Instruments manufacturer datasheet. Typical applications include portable media players, cellular phones, personal digital assistants, and other low-voltage systems in which a host controller needs extra discrete outputs. The device can expand an output-limited controller, support controlled indicators or peripheral signaling, and reduce the pin count required from the host integrated circuit. Its small RUG package is particularly useful when component area and routing density are more important than a large through-hole footprint. A key design consideration is the relationship between supply voltage, output behavior, and the master-generated timing waveform. Keep the single data trace short, provide a stable supply, and validate the Setup and output timing over the full operating-temperature range. Do not assume that a cross-reference device with a similar function is pin-to-pin compatible; confirm package geometry, pin assignment, supply range, and protocol timing before making a replacement. This product summary organizes the TCA5405RUGR function, voltage limits, package details, replacement constraints, comparison points, and application guidance into one engineering reference. It emphasizes the information needed to assess footprint reuse, interface timing, low-voltage operation, and the distinction between a functional substitute and a true drop-in replacement.

RFQ Contact
TCA6408PW - 8-Bit I2C I/O Expander | Texas Instruments
TCA6408PW

TCA6408PW - 8-Bit I2C I/O Expander | Texas Instruments

The Texas Instruments TCA6408PW is an 8-bit I2C and SMBus I/O expander supporting operation from 1.65 V to 5.5 V at up to 400 kHz, housed in a 16-pin TSSOP package. It provides eight general-purpose bidirectional port pins for remote input and output expansion, plus dedicated interrupt, reset, and configuration-register functions. An I/O expander is a bus-interface IC that extends the number of general-purpose inputs and outputs available to a microcontroller or other embedded controller. In the electronic-component hierarchy, the TCA6408PW is an I2C/SMBus interface controller, a serial interface expander, an interface IC, and ultimately a semiconductor. It reduces the number of host GPIO pins required for switches, indicators, sensors, and other external signals. The device's principal features include eight configurable I/O ports, a two-wire serial interface with a maximum clock frequency of 400 kHz, a broad 1.65 V to 5.5 V operating-voltage range, an interrupt output, a reset input, and configuration registers. These functions allow the host processor to read and control remote digital lines while receiving an interrupt when a relevant input condition occurs. The TCA6408PW uses addressable I2C control registers to configure port direction and input/output data. This register-based architecture keeps peripheral control separate from the host's limited GPIO resources. According to the Texas Instruments manufacturer datasheet, the device is intended for general-purpose remote I/O expansion across many microcontroller families using the I2C interface with SCL and SDA signaling. Typical applications include industrial control panels, battery-powered portable equipment, communications equipment, programmable logic controllers, and compact embedded systems with multiple discrete controls. The 1.65 V minimum operating voltage supports low-voltage portable systems, while the 5.5 V maximum covers conventional 5 V logic environments. The 400 kHz bus rate permits efficient register access when several compatible devices share the bus. Designers should account for the host's I2C address allocation, pull-up requirements on SDA and SCL, and the electrical characteristics of every attached P-port signal. Firmware should configure each port direction before enabling its outputs, and the reset, configuration, and interrupt functions should be considered when defining startup and event-handling behavior. This product page consolidates the verified distributor information, interface details, same-package replacement candidates, and application-oriented design guidance. It also distinguishes documented parameters from values that still require confirmation from the manufacturer datasheet, helping engineers evaluate TCA6408PW procurement and PCB drop-in decisions efficiently.

RFQ Contact
TCA6408PWR - 8-Bit I2C I/O Expander | Texas Instruments (Tape & Reel)
TCA6408PWR

TCA6408PWR - 8-Bit I2C I/O Expander | Texas Instruments (Tape & Reel)

The Texas Instruments TCA6408PWR is an 8-bit I2C and SMBus I/O expander supporting operation from 1.65 V to 5.5 V at up to 400 kHz, housed in a 16-pin TSSOP package. It provides eight general-purpose bidirectional port pins for remote input and output expansion, plus dedicated interrupt, reset, and configuration-register functions. An I/O expander is a bus-interface IC that extends the number of general-purpose inputs and outputs available to a microcontroller or other embedded controller. In the electronic-component hierarchy, the TCA6408PWR is an I2C/SMBus interface controller, a serial interface expander, an interface IC, and ultimately a semiconductor. It reduces the number of host GPIO pins required for switches, indicators, sensors, and other external signals. The device's principal features include eight configurable I/O ports, a two-wire serial interface with a maximum clock frequency of 400 kHz, a broad 1.65 V to 5.5 V operating-voltage range, an interrupt output, a reset input, and configuration registers. These functions allow the host processor to read and control remote digital lines while receiving an interrupt when a relevant input condition occurs. The TCA6408PWR uses addressable I2C control registers to configure port direction and input/output data. This register-based architecture keeps peripheral control separate from the host's limited GPIO resources. According to the Texas Instruments manufacturer datasheet, the device is intended for general-purpose remote I/O expansion across many microcontroller families using the I2C interface with SCL and SDA signaling. Typical applications include industrial control panels, battery-powered portable equipment, communications equipment, programmable logic controllers, and compact embedded systems with multiple discrete controls. The 1.65 V minimum operating voltage supports low-voltage portable systems, while the 5.5 V maximum covers conventional 5 V logic environments. The 400 kHz bus rate permits efficient register access when several compatible devices share the bus. Designers should account for the host's I2C address allocation, pull-up requirements on SDA and SCL, and the electrical characteristics of every attached P-port signal. Firmware should configure each port direction before enabling its outputs, and the reset, configuration, and interrupt functions should be considered when defining startup and event-handling behavior. This product page consolidates the verified distributor information, interface details, same-package replacement candidates, and application-oriented design guidance. It also distinguishes documented parameters from values that still require confirmation from the manufacturer datasheet, helping engineers evaluate TCA6408PWR procurement and PCB drop-in decisions efficiently.

RFQ Contact
TCA6416ARTWR - 16-Bit I2C I/O Expander with Voltage Translation | TI
TCA6416ARTWR

TCA6416ARTWR - 16-Bit I2C I/O Expander with Voltage Translation | TI

The Texas Instruments TCA6416ARTWR is a 16-bit translating I2C/SMBus I/O expander with 1.65V to 5.5V operation, 400 kHz Fast Mode I2C support, voltage translation between host and port banks, and an open-drain interrupt output, housed in a 24-pin WQFN (RTW) 4x4 mm package with exposed thermal pad. An I/O expander is a category of bus-interface IC that uses a serial protocol (typically I2C or SPI) to add parallel general-purpose input/output pins to a host microcontroller whose native GPIO count is insufficient. Architecturally the TCA6416ARTWR sits beneath the "I2C peripheral" hierarchy: it is a slave I2C device that decodes SCL/SDA traffic, drives 16 quasi-bidirectional I/O ports, and exposes a polarity-inversion register, configuration register, input/output register, and a maskable interrupt. Voltage translation allows a 1.8V host MCU to switch 5V external loads without level-shifters, which is essential when interfacing legacy industrial or LED-driver peripherals. Key features include 16 individually configurable I/O bits, hardware-address pins (A0/A1/A2) for up to 8 devices on one bus (128 total ports), an active-low RESET input, an open-drain INT output that signals input-state changes, and 5V tolerant I/O ports with 25 mA sink capability per pin. The WQFN-24 (RTW) 4x4 mm package offers a low 0.8 mm height, suitable for space-constrained handheld and embedded designs. The TCA6416ARTWR implements a write-then-read protocol where the host writes a command byte to select the target register (Input, Output, Polarity Inversion, or Configuration), then reads or writes the corresponding data byte. The interrupt is cleared by reading the input port register, giving firmware a clean edge-triggered event model. Internal pull-up current sources on each port line enable direct connection to switches or buttons without external resistors. Typical applications include expanding GPIO on portable consumer electronics, industrial control panels, IoT sensor hubs, white-goods HMI boards, and any design where a low-pin-count MCU (e.g., a 32-pin Cortex-M0) needs additional buttons, LEDs, or relay drivers. It is frequently paired with low-pin-count MCUs to keep BOM cost down. When designing with this device, place 0.1 uF decoupling capacitors close to VCCI and VCCP supply pins, keep the I2C SCL/SDA traces short, and ensure pull-up resistors (typically 4.7 kohm at 400 kHz) are sized against bus capacitance. The RESET pin should be tied to VCCI through a 10 kohm resistor unless driven by the host. This page synthesizes verified distributor stock, drop-in pin-compatible alternatives, and practical design notes not consolidated in the manufacturer datasheet, helping engineers shorten component selection time and avoid sourcing risk for production builds.

RFQ Contact
TCA6416PW - 16-Bit I2C I/O Expander | Texas Instruments
TCA6416PW

TCA6416PW - 16-Bit I2C I/O Expander | Texas Instruments

Texas Instruments TCA6416PW is a 16-bit I2C/SMBus I/O expander with a 1.65 V to 5.5 V operating supply range, 400 kHz bus support, interrupt output, reset control, and configuration registers in a 24-pin TSSOP package. It adds 16 general-purpose I/O ports to a host microcontroller through a two-wire serial interface, reducing the number of GPIO pins required in compact embedded systems. An I2C I/O expander is a type of interface IC and serial port expander that sits between a host processor and external digital lines. Its position in the hierarchy is I2C I/O expander > serial I/O expander > interface IC > semiconductor. The device is useful when a design needs more input, output, or bidirectional GPIO resources than the host controller can provide directly. Key features include 16 configurable I/O ports, bidirectional voltage-level translation through the 1.65 V to 5.5 V operating range, an interrupt output for change notification, a reset input, and configuration registers. The verified product information identifies the TCA6416 as an I/O expander for general-purpose remote I/O expansion across common microcontroller families using SCL and SDA. The TCA6416PW ordering option is supplied in a 24-pin TSSOP package. The device communicates through the I2C/SMBus-compatible two-wire interface at up to 400 kHz according to DigiKey's product listing. Configuration registers allow the host software to identify inputs, outputs, and polarity behavior, while the interrupt output provides a way for the host to react to a change on a monitored port. The reset and configuration features support deterministic initialization and power-management sequencing. Typical uses include industrial control panels, sensor and actuator interfaces, communication equipment, instrumentation, and embedded systems that need additional GPIO lines. It is particularly useful when board area, connector count, or host-controller pin availability is constrained, because sixteen external digital lines are added without dedicating sixteen parallel microcontroller pins. Designers should confirm the I2C pull-up requirements, address configuration, voltage levels, and reset timing in the manufacturer datasheet. The TSSOP footprint requires careful PCB layout and adequate clearance for the 24-pin package. Firmware should also define input, output, and polarity behavior before enabling interrupt-driven event handling. The manufacturer product page and verified distributor listings provide the primary source for electrical and ordering details.

RFQ Contact
TCA6416PWR - 16-Bit I2C I/O Expander | Texas Instruments (Tape & Reel)
TCA6416PWR

TCA6416PWR - 16-Bit I2C I/O Expander | Texas Instruments (Tape & Reel)

Texas Instruments TCA6416PWR is a 16-bit I2C/SMBus I/O expander with a 1.65 V to 5.5 V operating supply range, 400 kHz bus support, interrupt output, reset control, and configuration registers in a 24-pin TSSOP package. It adds 16 general-purpose I/O ports to a host microcontroller through a two-wire serial interface, reducing the number of GPIO pins required in compact embedded systems. An I2C I/O expander is a type of interface IC and serial port expander that sits between a host processor and external digital lines. Its position in the hierarchy is I2C I/O expander > serial I/O expander > interface IC > semiconductor. The device is useful when a design needs more input, output, or bidirectional GPIO resources than the host controller can provide directly. Key features include 16 configurable I/O ports, bidirectional voltage-level translation through the 1.65 V to 5.5 V operating range, an interrupt output for change notification, a reset input, and configuration registers. The verified product information identifies the TCA6416 as an I/O expander for general-purpose remote I/O expansion across common microcontroller families using SCL and SDA. The TCA6416PWR ordering option is supplied in a 24-pin TSSOP package. The device communicates through the I2C/SMBus-compatible two-wire interface at up to 400 kHz according to DigiKey's product listing. Configuration registers allow the host software to identify inputs, outputs, and polarity behavior, while the interrupt output provides a way for the host to react to a change on a monitored port. The reset and configuration features support deterministic initialization and power-management sequencing. Typical uses include industrial control panels, sensor and actuator interfaces, communication equipment, instrumentation, and embedded systems that need additional GPIO lines. It is particularly useful when board area, connector count, or host-controller pin availability is constrained, because sixteen external digital lines are added without dedicating sixteen parallel microcontroller pins. Designers should confirm the I2C pull-up requirements, address configuration, voltage levels, and reset timing in the manufacturer datasheet. The TSSOP footprint requires careful PCB layout and adequate clearance for the 24-pin package. Firmware should also define input, output, and polarity behavior before enabling interrupt-driven event handling. The manufacturer product page and verified distributor listings provide the primary source for electrical and ordering details.

RFQ Contact
TCA6416PWT - 16-Bit I2C I/O Expander | Texas Instruments
TCA6416PWT

TCA6416PWT - 16-Bit I2C I/O Expander | Texas Instruments

Texas Instruments TCA6416PWT is a 16-bit translating I2C/SMBus I/O expander with a 1.65 V to 5.5 V operating supply range, interrupt output, reset input, and configuration registers in a 24-pin TSSOP package. It expands a serial I2C or SMBus connection into 16 general-purpose input/output ports, reducing the number of host-controller pins required by boards containing buttons, LEDs, logic signals, or control lines. An I/O expander is an interface IC that sits between a host processor and peripheral GPIO devices. The I2C or SMBus interface carries commands and register data over a compact serial bus, while the parallel port pins provide individually controlled digital connections. In the product hierarchy, the TCA6416PWT is an I/O expander, a serial-interface peripheral controller, and ultimately an integrated circuit used to extend digital input/output capacity. The device supports operation from 1.65 V to 5.5 V and provides voltage-level translation between the host bus and external GPIO circuitry. According to the Texas Instruments product page, it includes interrupt, reset, and configuration registers. The open-drain interrupt output indicates that an input state differs from the corresponding Input Port register state, allowing the host to avoid continuous polling. The RESET pin initiates the same reset and initialization sequence as power-on reset. Communication with the TCA6416PWT is supported at I2C/SMBus rates up to 400 kHz. The translated serial interface lets a host operating at one logic level communicate with attached circuitry operating at another voltage level within the device's specified operating range. This is particularly useful in compact industrial, communications, consumer, and embedded-control products where the controller has too few direct GPIO pins. TCA6416PWT applications include remote push-button panels, LED status indicators, relay-control interfaces, sensor digital outputs, and general board-level GPIO expansion. Designers can configure ports as inputs or outputs through the device registers, read input states, and receive an interrupt when a monitored input changes. The 24-pin TSSOP package is suitable for conventional surface-mount PCB assembly and offers a practical pin count for a 16-port device with serial control and interrupt support. When laying out the circuit, place the device close to the connector or controlled circuitry reached by the 16 port lines, while keeping the I2C bus routing short and away from high-current switching paths. Confirm pull-up resistor requirements, address configuration, logic thresholds, and the open-drain interrupt connection in the manufacturer datasheet. This page combines the device specifications, sourcing guidance, drop-in alternatives, comparison data, and application-focused engineering guidance for faster component evaluation and PCB planning.

RFQ Contact
TCA6424ARGJR - 24-bit I2C/SMBus I/O Expander | Texas Instruments
TCA6424ARGJR

TCA6424ARGJR - 24-bit I2C/SMBus I/O Expander | Texas Instruments

The Texas Instruments TCA6424ARGJR is a 24-bit I2C/SMBus I/O expander housed in a 32-pin UQFN (RGJ) 5x5 mm package with an exposed thermal pad. The device operates from a 1.65 V to 5.5 V supply on the I2C/SMBus side (VCCI) and supports 1.8 V, 2.5 V, 3.3 V and 5 V tolerant I/O banks on the P-port side (VCCP). It communicates through the standard I2C interface up to 400 kHz and provides 24 general-purpose bidirectional I/O lines organized as three 8-bit ports (P0, P1, P2). An I/O expander is a category of interface IC that adds extra general-purpose digital input/output lines to a microcontroller or processor that has run out of native GPIOs. In the broader taxonomy, the TCA6424ARGJR sits at: I/O expander -> peripheral expander -> interface IC -> integrated circuit. The device addresses a fundamental I/O shortage problem in compact, GPIO-constrained designs such as mobile phones, wearables, and low-cost MCUs without resorting to a more expensive processor. Key features include an open-drain interrupt output (INT) that asserts whenever any input state differs from the corresponding Input Port register, a hardware RESET pin that re-initializes all registers without removing power, and configurable register banks that allow simultaneous access without locking. The device supports standard (100 kHz) and fast (400 kHz) I2C modes and provides three hardware address pins (A0, A1, A2), allowing up to eight devices on the same I2C bus for a total of 192 I/O lines. Typical applications include adding keypad scanning, LED indicators, push-button monitoring, and GPIO expansion in cell phones, media players, industrial HMI panels, gaming consoles, and infotainment systems. The wide voltage tolerance (1.65 V to 5.5 V) makes it particularly useful when bridging a 1.8 V SoC to legacy 5 V peripherals. When designing with this part, ensure the VCCI supply is present whenever the device is communicating; the P-port voltage (VCCP) may be lower than VCCI. Place 0.1 uF decoupling capacitors close to both VCCI and VCCP pins. If multiple TCA6424A devices share the bus, assign unique A0/A1/A2 addresses and pull the INT outputs together or read each individually to avoid contention. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone. The UQFN-32 (RGJ) package footprint, configurable register banks, and RESET pin distinguish the TCA6424ARGJR from lower-cost expanders such as the TCA6408A or PCF8575.

RFQ Contact
TCA8418RTWR - 18-Bit 1MHz Keypad Scanner | Texas Instruments
TCA8418RTWR

TCA8418RTWR - 18-Bit 1MHz Keypad Scanner | Texas Instruments

Texas Instruments TCA8418RTWR is an 18-bit I2C/SMBus keypad scanner and GPIO expander with a 1.65 V to 3.6 V operating range, 1 MHz bus speed, interrupt and reset functions, and support for as many as 80 keys. The device is supplied in a 24-pin WQFN RTW package measuring 4 mm by 4 mm. Its 18 general-purpose I/O lines can be configured as eight keypad rows and ten columns, while integrated pullup resistors simplify attached passive key matrices. A keypad scanner is an interface IC that detects button presses and reports their locations through a serial bus. The TCA8418 belongs to the broader GPIO expander and human-machine-interface controller hierarchy. It periodically scans matrix inputs, manages event and debounce functions, and signals the host through an interrupt output. This allows a microcontroller or application processor to read one or more key states over I2C instead of dedicating individual input pins to every switch. The principal feature set includes 18 configurable I/O pins, eight-row by ten-column keypad support, up to 80 keys, 1 MHz I2C/SMBus operation, and integrated ESD protection. A dedicated interrupt output reduces the need for continuous host polling, while a reset input supports deterministic initialization. The 24-pin WQFN package also includes an exposed pad, allowing the PCB to provide a low-impedance thermal and electrical ground connection according to the manufacturer's land-pattern requirements. Technically, the device is designed for low-voltage embedded systems whose keypad capacitance and leakage characteristics suit the integrated scanning circuitry. The operating range of 1.65 V through 3.6 V supports connection to common embedded processor I/O voltages. Its 1 MHz serial interface capability provides higher communication bandwidth than slower standard-mode-only keypad controllers, although the host bus, pullups, capacitance, and firmware must all support the selected operating rate. Typical uses include portable consumer equipment, personal digital assistants, portable audio and video products, and smartphones, as identified by the manufacturer. It can also manage compact numeric keypads, function buttons, menu controls, and general-purpose digital input/output lines in industrial panels or embedded control heads. The interrupt architecture is particularly useful in battery-powered equipment because it allows the processor to remain idle between key events rather than poll the keypad continuously. PCB implementation should prioritize short I2C routing, correct pullup placement, exposed-pad solderability, and protection from conductive contamination around the keys. Confirm the exact pin assignments and pin multiplexing options in the manufacturer pin-description table before assigning rows, columns, GPIOs, interrupt, reset, or ground functions. Avoid adding external row or column pullups unless the selected operating mode or application requires them, because the device already incorporates integrated pullup circuitry. This product page consolidates the manufacturer's key specifications, verified sourcing information, pin-package constraints, and application guidance into a single engineering reference. It also separates confirmed electrical facts from parameters that require consultation of the full TCA8418 datasheet, helping designers plan keypad scans, bus connections, PCB layout, and firmware integration before layout release.

RFQ Contact
TCA8424RHAR - 24-Bit I2C Keypad Scanner | Texas Instruments
TCA8424RHAR

TCA8424RHAR - 24-Bit I2C Keypad Scanner | Texas Instruments

The Texas Instruments TCA8424RHAR is a low-voltage 8×16 keypad scanner with a 24-bit key-state register, a 1.65 V to 3.6 V supply range, and an I2C/SMBus-compatible interface rated for operation up to 1 MHz. The device is packaged in a 40-pin VQFN measuring 6 mm × 6 mm and supports as many as 128 keys. An interrupt output allows the host processor to be notified when the scanned key matrix changes, reducing unnecessary polling and helping conserve power in portable and embedded systems. A keypad scanner is an interface integrated circuit that converts the electrical state of a matrix of switches into a compact digital status value. In the system hierarchy, it belongs to the interface-controller family within integrated circuits, alongside I2C and SMBus peripherals, GPIO expanders, and human-interface-device controllers. The TCA8424RHAR is designed to sit between a mechanical keypad matrix and an embedded host such as a microcontroller, leaving the host to interpret recognized key events and perform application-specific actions. The principal feature is support for an 8×16 matrix, providing 128 scanning positions in a compact physical footprint. Its 24-bit key-state register provides a defined digital representation of the matrix, while the interrupt signal supports event-driven host communication. Operation from 1.65 V to 3.6 V makes the scanner suitable for low-voltage embedded systems, and the 1 MHz interface capability allows it to operate on a faster shared serial bus when host timing and bus capacitance permit. The device combines matrix scanning with an I2C/SMBus-compliant host interface and HID-oriented keyboard-scanner functionality. These characteristics make it useful where a conventional matrix requires many host GPIO pins or where a dedicated serial keypad controller simplifies firmware. The scanner limits the host interface to the serial bus and interrupt line rather than requiring one GPIO input for every key position. Configuration and status reporting are handled through the serial interface, while the interrupt output indicates that the matrix state requires attention. Typical applications include consumer keypads, security-access panels, industrial control membranes, portable instruments, and compact human-interface panels. A product with 128 possible switch positions can use the full scanner capacity, while systems with fewer switches can leave unused matrix positions unconnected according to the manufacturer's implementation guidance. The device can also complement a touchscreen controller by providing physical-key input alongside touch input when a product requires both interaction methods. Layout planning should account for the 40-pin VQFN footprint, exposed thermal pad, decoupling requirements, and signal integrity of the I2C bus. Place the input and interface bypass capacitors close to their corresponding pins, route the interrupt trace away from high-current switching nodes, and confirm pull-up values against the bus voltage, capacitance, and operating speed. Because the 1 MHz rating is a maximum interface capability rather than a requirement for every design, use a conservative bus rate when signal-integrity margins are limited. This product page combines the manufacturer’s device capabilities with package, sourcing, interface, and design information in one engineering-focused reference. It also identifies the limits of the available substitution evidence: no same-package, pin-to-pin replacement is asserted unless its electrical characteristics and land pattern have been independently confirmed.

RFQ Contact
TCA9406DCTR - 2-Bit Bidirectional I2C/SMBus Level Translator | TI
TCA9406DCTR

TCA9406DCTR - 2-Bit Bidirectional I2C/SMBus Level Translator | TI

The Texas Instruments TCA9406DCTR is a 2-bit bidirectional I2C bus and SMBus voltage-level translator with an output enable (OE) input, operational from 1.65 V to 3.6 V on the A-side (VCCA) and 2.3 V to 5.5 V on the B-side (VCCB), housed in an 8-pin SM8/SSOP surface-mount package with 8 kV HBM ESD protection. A voltage-level translator is an interface IC that bridges digital signal domains operating at different supply rails, allowing a microcontroller running at 1.8 V or 3.3 V to safely communicate with peripheral devices on a 5 V bus. Within the signal-chain hierarchy, level translators sit between logic ICs and physical bus lines and are essential members of the I2C/SMBus interface family, where open-drain bidirectional lines cannot be shifted with simple resistor dividers. Key differentiating specifications include true bidirectional operation without a direction pin, support for the 1-MHz Fast-mode Plus I2C class of operation with data rates up to 24 Mbps in general-purpose push-pull use, and 8 kV human-body-model ESD robustness on the bus pins. The dedicated OE input lets the system place both channels in the high-impedance state during power sequencing or bus reconfiguration, preventing bus contention and back-powering through partial-rail conditions. Architecturally, the TCA9406 integrates an internal boost/reference generator on the B side so that only two supply pins (VCCA and VCCB) and a minimal external component count are required - no external pull-up resistors to a reference rail are needed, unlike pass-gate translators such as the TI PCA9306. This integrated drive makes rise and fall times far less dependent on bus loading, which matters when the bus runs at 400 kHz or 1 MHz with cable or connector capacitance. Typical applications include I2C sensor interfacing in battery-powered products, SMBus communication between 3.3 V management controllers and 5 V power-supply modules, and level shifting between low-voltage MCUs and 5 V EEPROMs or RTCs. It fits anywhere a 1.8 V, 2.5 V, or 3.3 V host must drive a 5 V peripheral bus reliably. A key design consideration: the OE pin should be driven by a supply-rail supervisor or held low until both VCCA and VCCB are stable, since enabling the translator before the higher rail is up can momentarily clamp the bus. This page synthesizes distributor pricing and stock, drop-in alternative analysis against the NXP PCA9306, pinout data, and practical design notes not found in the manufacturer datasheet.

RFQ Contact
TCA9509RVHR - 2-Bit I2C Level Translator | Texas Instruments
TCA9509RVHR

TCA9509RVHR - 2-Bit I2C Level Translator | Texas Instruments

The Texas Instruments TCA9509RVHR is a 2-bit level-translating I2C/SMBus buffer and repeater operating up to 400 kHz, with an internal 1 mA pull-up current source and an 8-pin X2QFN package measuring 1.6 mm by 1.6 mm. It is designed to isolate voltage domains while preserving bidirectional bus communication. An I2C level translator is an interface IC that connects logic operating at different voltage levels on the same serial bus. Its position in the hierarchy is I2C repeater, level translator, interface IC, and ultimately semiconductor. This bidirectional separation helps prevent low-voltage devices from receiving signals that exceed their input limits and helps keep high-voltage devices from exposing low-voltage nodes to excessive voltage. The principal features are two independently level-translated bus channels, operation up to 400 kHz, an internal 1 mA current source, and support for both I2C and SMBus signaling. The small X2QFN package supports compact PCB layouts where board area is constrained. Its buffer function can also isolate capacitive loading between bus segments and improve signal integrity in multi-board or multi-device systems. The B-side drivers use SMBus-compatible I/O levels, while the A-side uses current sensing to identify LOW states and avoid bus lock-up. The A-side includes the internal 1 mA current source for pull-up support. This arrangement accommodates smaller LOW-state voltage swings while retaining bidirectional data transfer, which is important when connecting peripherals with different supply voltages. Typical applications include voltage-level translation between low-voltage sensors and higher-voltage controllers, SMBus management interfaces, compact industrial modules, embedded instrumentation, and systems that divide a long I2C bus into shorter electrically isolated segments. The device is particularly useful when cables, connectors, or PCB routing introduce capacitance between bus nodes. When laying out the circuit, treat the A-side and B-side pull-up networks as separate domains and confirm that the external pull-up strength works with the intended bus voltage and capacitance. Avoid adding unnecessary capacitance near the small package, and verify signal rise times at the maximum intended I2C clock rate. Bus timing and voltage margins remain the responsibility of the final board design. This page combines the manufacturer product information, ordering data, documented cross-reference details, packaging characteristics, and practical design guidance in one engineering-focused view. It also distinguishes true pin-compatible interchange from merely similar I2C switching devices, helping designers make a replacement decision without assuming that equal functionality guarantees equal footprint or pin behavior.

RFQ Contact
TCA9517DGKR - I2C Bus Repeater Level Translator | TI
TCA9517DGKR

TCA9517DGKR - I2C Bus Repeater Level Translator | TI

The Texas Instruments TCA9517DGKR is a 2-channel, bidirectional level-translating I2C bus repeater and buffer supporting 400 kHz (Fast-mode) I2C and SMBus operation, with A-side supply from 0.9 V to 5.5 V and B-side supply from 2.7 V to 5.5 V, housed in an 8-pin VSSOP (DGK) package. A level-translating I2C bus buffer is an interface IC that sits between two segments of an I2C or SMBus, electrically isolating the bus capacitance and logic levels on each side. In the interface IC hierarchy, it belongs to the signal buffer/repeater family of level translators, which sit above simple transistors and below full protocol bridges. By segmenting the bus, the repeater allows longer buses and more devices than the I2C standard capacitance limit would otherwise permit. Key features include support for both standard-mode (100 kHz) and fast-mode (400 kHz) I2C signaling, an enable (EN) pin for bus isolation and power sequencing, and powered-off high-impedance I2C pins that effectively remove the device from the bus when either supply is absent. The TCA9517 also incorporates an acceleration feature that speeds up the rising edge of SDA and SCL on the B side. Architecturally, the TCA9517 uses two distinct driver types. The A-side drivers operate from 0.9 V to 5.5 V and drive more current without requiring the buffered-low static offset voltage, so a low on the B side translates to a nearly 0 V hard low on the A side. This accommodates the smaller voltage swings of lower-voltage logic such as 1.2 V or 1.8 V I2C peripherals. The B side retains the static voltage offset needed for hot-swapping and rise-time acceleration. Typical applications include I2C bus expansion in industrial automation, server and telecom backplane management (SMBus), and level translation between 1.8 V microcontrollers and 3.3 V sensors or EEPROMs. Design consideration: the A-side output can sink more current than a plain MOSFET translator, so pay attention to total bus capacitance per segment; keep pull-up resistor values sized per segment rather than one pair for the whole bus. This page synthesizes distributor pricing, verified drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

RFQ Contact
TCA9517DGKRQ1 - Automotive I2C Level-Shifting Buffer | TI
TCA9517DGKRQ1

TCA9517DGKRQ1 - Automotive I2C Level-Shifting Buffer | TI

The Texas Instruments TCA9517DGKRQ1 is an automotive-grade, 2-bit level-translating I2C/SMBus buffer/repeater operating at up to 400 kHz, housed in an 8-pin VSSOP (DGK) package and qualified to AEC-Q100 for -40C to +125C operation. An I2C bus buffer, also called a level translator or bus repeater, is an interface IC that sits between two segments of an I2C or SMBus serial bus. Its role in the interface IC hierarchy is to isolate bus capacitance, allowing longer or more heavily loaded buses, and to translate logic voltage levels between devices powered from different supply rails, such as a 1.8V microcontroller talking to 5V peripherals. Key features include bidirectional voltage-level translation between low voltages down to 0.9 V on side A and 2.7 V to 5.25 V on side B, support for both standard-mode (100 kHz) and fast-mode (400 kHz) I2C plus SMBus, and a powered-off high-impedance state that isolates both bus segments when either supply rail is absent. The enable (EN) pin provides additional bus control, and open-drain I/O structures preserve the wired-AND nature of I2C. Technically, the TCA9517-Q1 drives both sides of the bus, refreshing rise times and removing the cumulative load of stubs and cables. Unlike passive FET level shifters, it does not trade drive strength for level translation, so clock stretching and multi-master arbitration are preserved. It supports up-translation, down-translation, and same-level buffering. Typical applications include automotive body electronics and infotainment I2C bus extension, PMBus/SMBus power-supply management in industrial systems, and level translation between 1.8V or 3.3V MCUs and 5V sensors or EEPROMs. Design consideration: because the device drives each side actively, do not connect the A and B sides to the same bus segment, and keep EN tied low until both supply rails are stable to avoid bus latch-up during power sequencing. This page synthesizes distributor pricing, drop-in alternatives, pinout data, and practical design notes not found in the manufacturer datasheet alone. Pricing shown as of 2026-10-19.

RFQ Contact
TCA9517DR - Level-Shifting I2C Bus Repeater | Texas Instruments
TCA9517DR

TCA9517DR - Level-Shifting I2C Bus Repeater | Texas Instruments

The Texas Instruments TCA9517DR is a 2-bit level-translating I2C/SMBus bus buffer supporting 400 kHz Fast Mode operation, with an A-side supply range of 0.9 V to 5.5 V and a B-side supply range of 3.0 V to 5.5 V, housed in an 8-pin SOIC (D) package. An I2C bus buffer (also called a bus repeater or level translator) is an interface IC that sits between two segments of an I2C or SMBus serial bus. Its role in the interface IC hierarchy is to electrically isolate the two segments while translating signal levels between devices powered at different voltages, allowing low-voltage microcontrollers to communicate safely with higher-voltage peripherals. A buffer also isolates bus capacitance, so each side can drive longer traces or more devices than a single unbuffered bus would allow. Key features include fully bidirectional level translation with no direction-control pin, a low-level input on the A-side set at 0.3 x VCCA that accommodates smaller voltage swings of lower-voltage logic, and a powered-off high-impedance state on all pins so the part never loads the bus when unpowered. According to the TCA9517 datasheet, the A-side drivers operate from 0.9 V to 5.5 V, drive more current than B-side drivers, and do not require a buffered low or static offset voltage, producing a nearly 0 V hard low on the A-side. Architecturally, the TCA9517 uses open-drain drivers with rise-time support rather than a static 0.5 V low offset on the A-side, distinguishing it from the older PCA9517 generation. The 230 ns maximum propagation delay preserves I2C Fast Mode timing margins at 400 kHz, and the two channels translate both SDA and SCA lines simultaneously. Typical applications include connecting 1.8 V or 3.3 V MCU I2C ports to 5 V EEPROMs, sensors, and RTCs in industrial and telecom equipment, isolating bus capacitance in long backplane runs, and buffering densely loaded SMBus segments. Design consideration: keep the A-side connected to the lower-voltage, higher-capacitance segment; the B-side static 0.5 V offset requires pairing buffers B-side to A-side in cascaded topologies. This page synthesizes distributor pricing, verified drop-in alternatives, pinout, and practical design notes not found in the manufacturer datasheet.

RFQ Contact
TCA9534DWR - 8-Bit I2C I/O Expander | Texas Instruments
TCA9534DWR

TCA9534DWR - 8-Bit I2C I/O Expander | Texas Instruments

The Texas Instruments TCA9534DWR is an 8-bit I2C/SMBus I/O expander operating from 1.65 V to 5.5 V, supporting bus speeds up to 400 kHz and housed in a 16-pin SOIC package. It adds eight configurable parallel input/output ports to a host controller while providing an interrupt output and configuration registers. An I/O expander is an interface IC that increases the number of digital input and output lines available to a microcontroller or embedded processor. The TCA9534 belongs to the I/O expander class within interface ICs and power-management ecosystems, using a two-wire serial bus to exchange register data with a host. It is particularly useful when a system needs a few additional control, status, or monitoring signals without assigning dedicated host-controller pins to each function. Key device features include eight configurable I/O pins, three I2C address inputs, and operation across a 1.65 V to 5.5 V supply range. The device supports I2C and SMBus communication at frequencies up to 100 kHz or 400 kHz. An interrupt output provides a hardware indication that an input or output state has changed, while the configuration registers control port direction and polarity behavior for individual pins. The TCA9534DWR supports both input and output operation for its eight-port group. Register-based configuration allows the firmware to select input or output directions, read input levels, and update output values. The three address inputs permit multiple expanders to share the same bus when the system requires additional I/O. Because the device includes configuration registers, application software can define port behavior without requiring a separate external GPIO controller. Typical applications include industrial control panels, sensor and relay interfaces, LED status panels, battery-powered instrumentation, programmable logic controllers, and compact embedded systems. The wide 1.65 V to 5.5 V operating range also makes the device suitable for mixed-voltage systems where the host operates below the conventional 5 V logic level. The interrupt output can reduce unnecessary host polling when an attached switch, sensor, or other external event changes state. Designers should confirm the board voltage, I2C pull-up arrangement, address configuration, and input thresholds before layout. The SDA and SCL pins require appropriate bus pull-ups, while address pins must be connected to valid logic levels before the device begins communicating. Decoupling and signal-integrity practices are especially important when the expander sits near long cables, switching regulators, or electrically noisy equipment. This product overview combines the device architecture, operating limits, bus behavior, application guidance, and drop-in comparison information to support faster engineering selection. It also highlights practical layout and firmware considerations that help engineers evaluate the TCA9534DWR within the complete embedded-control system rather than treating it only as a list of basic parameters.

RFQ Contact
TCA9534DWT - 8-Bit I2C I/O Expander | Texas Instruments
TCA9534DWT

TCA9534DWT - 8-Bit I2C I/O Expander | Texas Instruments

The Texas Instruments TCA9534DWT is an 8-bit I2C/SMBus I/O expander with interrupt output and configuration registers, operating from 1.65 V to 5.5 V and supporting both 100 kHz Standard-mode and 400 kHz Fast-mode bus speeds. The device is packaged in a 16-pin SOIC package and provides eight general-purpose parallel input/output ports. An I2C I/O expander is an interface IC that increases the number of digital input and output lines available to a host processor. The TCA9534DWT uses a two-wire bidirectional I2C or SMBus connection for register access, while the eight external pins can be configured individually as inputs or outputs. This makes it useful for reducing microcontroller pin count in control, sensing, and actuator systems. The TCA9534DWT provides separate input and output configuration registers, allowing each of the eight ports to be used as an input or output. It also includes an interrupt output for change detection on configured input ports. The 1.65 V to 5.5 V operating range supports low-voltage digital systems, while 100 kHz and 400 kHz bus operation accommodates both standard and faster embedded communication requirements. The 16-pin SOIC package provides a compact surface-mount footprint for industrial, consumer, communications, and embedded-control equipment. The device is designed for systems that need more general-purpose digital I/O without adding a larger processor or complex programmable logic. The manufacturer product page identifies the TCA9534 family as an I2C/SMBus interface IC with interrupt and configuration registers. Typical applications include relay and solenoid control, LED status and indicator interfaces, keypad or button scanning, sensor input collection, and expansion of a microcontroller's available digital lines. The TCA9534DWT is particularly appropriate when a bus-connected peripheral can reduce wiring complexity and preserve host-controller pins for communications, timing, or analog functions. When designing around the TCA9534DWT, confirm the address configuration and electrical limits against the manufacturer datasheet before layout. Use appropriate pull-up resistors on the I2C bus and account for the operating voltage of both the expander and connected peripherals. This page combines the manufacturer product information, distributor references, package details, application guidance, and drop-in comparison information for engineering review.

RFQ Contact
TCA9534PWR - 8-Bit I/O Expander | Texas Instruments
TCA9534PWR

TCA9534PWR - 8-Bit I/O Expander | Texas Instruments

The Texas Instruments TCA9534PWR is an 8-bit I2C and SMBus I/O expander with interrupt output and configuration registers, operating from 1.65 V to 5.5 V with a 400 kHz maximum bus clock in a 16-pin TSSOP package. The device provides eight general-purpose bidirectional I/O ports for systems whose microcontroller does not have enough local GPIO. An I/O expander is an interface IC that extends the number of digital input and output lines available to a host processor over a serial bus. The I2C interface connects the expander to a controller, while the eight parallel ports connect to switches, sensors, LEDs, relays, or other digital peripherals. In the system hierarchy, the TCA9534 is an interface IC and a GPIO expander built around an I2C-compatible serial interface. The TCA9534 includes three hardware address inputs, allowing up to eight devices to share one I2C bus. It also includes an interrupt output, configuration registers, and a power-on reset function that restores the device to its default state. The 1.65 V minimum supply voltage supports low-voltage embedded systems, while the 5.5 V maximum supports conventional 5 V peripherals and logic. The TCA9534PWR is suitable for industrial control boards, sensor interfaces, panel controls, LED indicators, configuration connectors, and compact embedded platforms. Its low-voltage operation and 400 kHz I2C speed make it useful when the host controller requires more GPIO resources without adding a high-speed switching regulator or a large package. The interrupt output allows the controller to service external state changes without continuous polling. Designers should place the device close to the I/O connector or controlled peripherals and route the I2C lines away from noisy switching nodes. Pull-up resistors must be selected for the actual bus voltage and capacitance. The three address pins should be configured before enabling the bus, and software must account for the TCA9534 register map and power-on reset behavior. The manufacturer datasheet should be used for the complete pin assignment and electrical limits. This page provides practical application guidance, parameter comparisons, drop-in replacement information, and design notes that support faster component selection and PCB implementation.

RFQ Contact
TCA9535DBR - 16-Bit I2C I/O Expander | Texas Instruments
TCA9535DBR

TCA9535DBR - 16-Bit I2C I/O Expander | Texas Instruments

Texas Instruments TCA9535DBR is a low-voltage, low-power 16-bit I2C and SMBus I/O expander with an interrupt output and configuration registers. It operates from 1.65 V to 5.5 V, supports I2C communication at up to 400 kHz, and provides 16 general-purpose parallel I/O lines in a 24-pin SSOP package. An I/O expander is an interface IC that increases the number of digital input and output pins available to a host controller. The host communicates with the TCA9535DBR through a two-wire I2C or SMBus interface, while the 16 external lines handle logic inputs, outputs, or mixed functions. In the system hierarchy, this device belongs to the interface IC family and bridges a serial control bus with parallel digital signals. The principal features are 16 independently configurable I/O pins, a 1.65 V to 5.5 V operating range, and a maximum bus frequency of 400 kHz. The interrupt output allows a connected controller to react when an input changes, reducing the need for continuous polling. Separate configuration registers support control of the direction and behavior of the I/O ports, while the device is designed for low-power operation. TCA9535DBR is packaged in a 24-pin SSOP, providing a compact surface-mount format for programmable control, monitoring, and signal-routing boards. Its I2C interface is suitable for buses that also carry configuration data or communicate with sensors, memory, and other interface devices. The 400 kHz capability allows the expander to operate on standard low-speed I2C systems without changing the host protocol. Typical applications include industrial control panels, programmable logic controllers, building automation equipment, test systems, and embedded products that require additional digital lines. The part can also expand button or switch inputs, control discrete logic signals, and provide interrupt-driven status reporting. Its small pin count relative to the number of external I/O lines helps conserve connector space and simplify system architecture. When designing around the TCA9535DBR, account for address selection, pull-up requirements, input thresholds, and the electrical characteristics of every attached signal. Confirm the board footprint and pin assignment against the manufacturer datasheet before release, especially when replacing a device with similar I/O count but different input or output polarity. The design notes and comparisons on this page provide practical guidance for firmware setup, PCB layout, and device selection.

RFQ Contact
TCA9535DBT - 16-Bit I/O Expander | Texas Instruments
TCA9535DBT

TCA9535DBT - 16-Bit I/O Expander | Texas Instruments

The Texas Instruments TCA9535DBT is a 16-bit I/O expander for the I2C or SMBus interface, operating from a 1.65 V to 5.5 V supply at up to 400 kHz. The device provides 16 general-purpose bidirectional I/O lines, an interrupt output, and configuration registers in a 24-pin SSOP package. An I/O expander is an interface IC that increases the number of digital input and output pins available to a host controller without requiring a larger microcontroller package. The TCA9535 belongs to the I/O expander hierarchy, where a serial I2C or SMBus connection controls parallel digital lines. Its 16 ports can operate as inputs, outputs, or mixed configurations, making it useful for control panels, sensor aggregation, relay interfaces, and compact embedded systems. The main features include a wide 1.65 V to 5.5 V operating range, 16 general-purpose I/O lines, separate configuration registers, and an interrupt output. The I2C interface supports operation up to 400 kHz, while the three address inputs allow multiple devices to share the same serial bus. The interrupt output lets the connected processor respond only when a programmed input or output event occurs instead of polling every port continuously. Internally, the TCA9535 separates the 16 I/O lines into four eight-bit ports. Each port has its own configuration register, while dedicated input and output registers provide independent control of direction and data. This organization supports mixed input and output operation without requiring a separate GPIO controller for every line. Three hardware address inputs select the device address used on the shared bus. Typical applications include expanding a microcontroller's available GPIO, reading discrete switches and sensors, driving LEDs or digital control signals, implementing a keypad interface, and controlling multiple peripheral enables. The low-voltage operation also suits battery-powered and portable equipment where the host and expander operate from a 1.8 V, 2.5 V, 3.3 V, or 5 V system rail. Design the bus carefully when several expanders share SDA and SCL. Keep pull-up resistors within the range specified by the manufacturer datasheet, route the bus away from noisy switching nodes, and account for capacitance when increasing cable length or the number of devices. Decoupling close to VCC and GND improves stability in compact systems. This product page combines the manufacturer's core electrical characteristics, package and pin information, compatibility-focused alternatives, application guidance, and practical design considerations to support faster component selection and PCB planning.

RFQ Contact
TCA9535PWR - 16-Bit I/O Expander | Texas Instruments
TCA9535PWR

TCA9535PWR - 16-Bit I/O Expander | Texas Instruments

Texas Instruments TCA9535PWR is a low-voltage 16-bit I2C and SMBus I/O expander with interrupt output and configuration registers, operating from 1.65 V to 5.5 V at up to 400 kHz and housed in a 24-pin TSSOP (PW) package. It adds 16 general-purpose parallel I/O lines to a host microcontroller or processor through a two-wire serial bus. An I/O expander is an interface IC that increases the number of digital input and output pins available to a host without requiring a large package or a dedicated parallel peripheral. The TCA9535PWR belongs to the broader I/O expander hierarchy, where each port bit can be independently configured as an input or output. Configuration, polarity-inversion, and interrupt functions make it suitable for systems that need remote control or change notification from external logic. The principal features include 16 independently configurable I/O pins, a 1.65 V to 5.5 V operating supply range, I2C/SMBus compatibility, and a 400 kHz bus rate. Separate configuration registers determine whether each port pin operates as an input with a high-impedance output driver or as an output. Polarity-inversion registers can reverse the logical interpretation of input pins, while the interrupt output provides a hardware indication of an input-state change. The two-wire interface reduces the number of host pins needed for peripheral expansion. The host writes to the configuration and polarity registers and reads port status over the serial bus. This arrangement is useful when the additional lines control relatively simple discrete functions rather than high-bandwidth data. The interrupt mechanism avoids continuous polling when a remote input or configured output state changes. Typical uses include LED and indicator control, button and switch input, relay-interface signaling, sensor-interface control, and general-purpose logic expansion in embedded products. The TCA9535PWR is particularly appropriate for low-voltage systems operating from 1.65 V through 5.5 V, including industrial control, communications equipment, consumer electronics, and programmable-logic applications. Design the power and signal path carefully. Confirm that every port-pin voltage remains within its applicable input and output limits, account for the total current drawn by simultaneously active outputs, and use pull-up resistors sized for the bus capacitance and operating speed. Treat the interrupt pin as an output signal from the expander and design firmware to clear the interrupt source before returning to normal polling. This product page combines manufacturer specifications, verified source links, pin-compatible alternatives, and application-oriented design guidance to accelerate component selection and PCB implementation. It also highlights the distinctions among device addressing and register behavior so engineers can identify the correct substitute before changing an approved design.

RFQ Contact
TCA9536-Q1 - 4-Bit I2C/SMBus I/O Expander AEC-Q100 | TI
TCA9536-Q1

TCA9536-Q1 - 4-Bit I2C/SMBus I/O Expander AEC-Q100 | TI

The Texas Instruments TCA9536-Q1 is a 4-bit remote I/O expander for the I2C bus and SMBus with configuration registers, operating from a 1.65V to 5.5V supply in an 8-pin X2SON package measuring just 1.35 mm x 0.8 mm. It provides general-purpose remote I/O expansion for most microcontroller families via the I2C interface and is AEC-Q100 qualified for automotive applications. An I/O expander is an interface IC that extends the number of general-purpose input/output (GPIO) pins of a microcontroller or system controller through a serial bus such as I2C or SMBus. In the hierarchy of embedded system components, the I/O expander sits within the interface IC family, alongside level translators, bus buffers, and serial transceivers, and functions as a remote GPIO peripheral for system masters that need additional discrete control or monitoring lines without adding a larger microcontroller. Key features of the TCA9536-Q1 include 4 configurable I/O pins that can be individually programmed as inputs or outputs through a 4-bit Configuration register, an Input Port register for reading pin states, an Output Port register for driving pins, and a Polarity Inversion register for active-HIGH or active-LOW operation. The device supports fast-mode I2C bus operation up to 1 MHz, uses only two bus lines (SDA and SCL), and operates across the wide 1.65V to 5.5V VCC range for compatibility with 1.8V, 2.5V, 3.3V, and 5V logic systems. The architecture implements four 4-bit registers (Configuration, Input Port, Output Port, and Polarity Inversion) accessible over the serial bus, with power-on reset defaulting all pins to inputs. Because the TCA9536-Q1 register map follows the widely deployed PCA9536 register convention, the same software drivers used for PCA9536-class expanders generally work unchanged, simplifying migration and second-sourcing within an existing firmware stack. Typical applications include automotive body-control modules, GPIO expansion in space-constrained sensor nodes, keypad or switch monitoring, LED and relay control through external drivers, and power-rail sequencing enables in infotainment and cluster displays. Its tiny X2SON footprint makes it especially attractive where board area is the limiting factor. Design consideration: because the X2SON package places multiple pins on very fine pitch beneath the die, follow TI's recommended PCB land pattern exactly, including via-in-pad thermal relief, and verify solderability with the correct reflow profile for the Q1 automotive grade. This page synthesizes verified distributor data, drop-in alternative analysis, and practical design guidance that goes beyond the raw datasheet parameters.

RFQ Contact
TCA9538DBR - 8-Bit I2C I/O Expander | Texas Instruments
TCA9538DBR

TCA9538DBR - 8-Bit I2C I/O Expander | Texas Instruments

Texas Instruments TCA9538DBR is an 8-bit I2C/SMBus low-power I/O expander with a 1.65 V to 5.5 V operating range, 400 kHz bus speed, and a 16-pin SSOP package. It adds eight general-purpose input or output ports through a two-wire serial interface while providing interrupt, reset, and configuration registers. The device is intended for systems in which a host controller needs more parallel I/O than its native package or connector resources can provide. An I/O expander is an interface IC that extends the number of digital input and output pins available to a host processor. The TCA9538 belongs to the I2C interface hierarchy, where the I2C or SMBus protocol links the expander to a controller such as a microcontroller. Each port can be configured as an input or output, allowing the same circuit to support switches, sensors, logic-control signals, LEDs, and other digital peripherals while conserving host pins and reducing interconnect complexity. The principal operating parameters are an 8-bit port count, a 1.65 V minimum supply voltage, a 5.5 V maximum supply voltage, and support for a 400 kHz I2C bus. According to the Texas Instruments product page, the device also includes an interrupt output, reset control, and configuration registers. These functions support event-driven peripheral monitoring and orderly control of multiple downstream signals without continuous polling by the host processor. The TCA9538DBR is a remote, low-power parallel-interface device rather than a general-purpose processor or transceiver. Its serial control path uses the two-wire I2C or SMBus interface, while the eight parallel ports connect to digital circuitry in the target system. The SSOP-16 package provides a compact surface-mount format, and the manufacturer lists the part as active. Its operating temperature range is -40 °C to +85 °C, supporting industrial-temperature equipment when correctly handled for thermal and soldering requirements. Typical uses include control-panel backlights, sensor and switch interfaces, relay-control inputs, programmable logic interfaces, battery-powered monitoring equipment, and communication equipment requiring additional GPIO. The TCA9538 is especially useful when the host controller has limited spare pins but the system still needs eight independently configurable digital lines and an interrupt mechanism for status changes. Design the bus with pull-up resistors appropriate for the operating voltage, confirm that the 400 kHz bus rate is compatible with the complete bus capacitance and every attached peripheral, and account for logic thresholds when the expander operates alongside mixed-voltage devices. Place the interface pins, supply decoupling, and pull-up network to minimize routing delay and maintain signal integrity across the board. This product record combines the manufacturer’s electrical and package information with practical interface-selection guidance, pinout-location references, application analysis, and compatibility cautions. It also distinguishes true same-package drop-in replacements from related expanders that differ in footprint, voltage tolerance, interrupt behavior, or register implementation and therefore require engineering review before substitution.

RFQ Contact