Products (44,000+)

LM2904PWR - Dual 700 kHz Op Amp, 26 V | Texas Instruments (Tape & Reel)
LM2904PWR

LM2904PWR - Dual 700 kHz Op Amp, 26 V | Texas Instruments (Tape & Reel)

The Texas Instruments LM2904PWR is a dual general-purpose operational amplifier with a 700 kHz gain-bandwidth product, 26 V maximum supply capability, and an 8-pin TSSOP package. The device contains two independent, frequency-compensated amplifiers that can operate from a single supply or split supply, making it suitable for signal conditioning, buffering, and general-purpose analog control applications. Its 0.7 mA typical supply-current drain is specified as being independent of supply voltage, helping conserve power across a broad operating range. An operational amplifier, or op amp, is an analog integrated circuit that uses high open-loop gain to amplify the difference between two input voltages. A dual op amp combines two amplifiers in one package, allowing both channels to share a supply while remaining electrically independent. Within the broader semiconductor hierarchy, the LM2904PWR belongs to the amplifier IC, operational-amplifier, analog-signal-conditioning, and integrated-circuit families. It is a widely recognized general-purpose alternative to newer precision and low-noise amplifier families when voltage range, low power, and functional simplicity matter more than low offset or rail-to-rail operation. The principal operating characteristics include a 26 V maximum supply voltage, a 700 kHz gain-bandwidth product, two amplifier circuits, and a typical supply-current drain of 0.7 mA. The common-mode input range includes ground, allowing the device to sense input signals close to the negative supply rail. Low input-bias and input-offset parameters are identified in the device literature, although exact minimum and maximum limits are not included in the retrieved data. The LM2904PWR therefore provides a practical balance of gain bandwidth, supply flexibility, and low supply-current demand. Internally, the LM2904 uses a frequency-compensated voltage-feedback architecture. This internal compensation means each amplifier can provide stable closed-loop operation without an external frequency-compensation network when configured for typical noninverting or inverting gains. The design is intended for general-purpose analog systems rather than precision instrumentation. Its 700 kHz gain-bandwidth product is adequate for audio-frequency signal conditioning, low-rate data acquisition, sensor interfaces, and industrial control blocks, but it is substantially slower than precision, high-speed, or rail-to-rail amplifier families. Typical uses include general-purpose signal amplification, low-frequency active filtering, current-to-voltage conversion for sensors, audio preamplification, comparator-style threshold conditioning with suitable output limits, and industrial control interfaces. The ability to operate from single or split supplies makes the part useful in systems whose signal range is referenced to ground. For battery-powered equipment, the typical 0.7 mA supply-current drain helps limit consumption, although the complete system current also depends on output current, load, amplifier configuration, and supply voltage. Designers should verify the exact common-mode, output-swing, offset-voltage, input-bias-current, slew-rate, and temperature limits from the manufacturer datasheet before fixing operating conditions. Input and output stability depends on layout, source impedance, load, and feedback topology. Decoupling should be placed close to the supply pins, and sensitive layouts should minimize parasitic capacitance and leakage around high-impedance inputs. The 8-pin TSSOP footprint is compact but requires careful lead pitch and thermal considerations during assembly. This product record combines the verified manufacturer identity, package, voltage, bandwidth, and power information with distributor pricing and cross-reference evidence. It also adds practical application guidance, honest substitution limits, package-level comparison data, and design notes intended to help engineers evaluate the LM2904PWR beyond a raw distributor listing.

RFQ Contact
LM2904PWRE4 - Dual 26V 700kHz Op Amp | Texas Instruments
LM2904PWRE4

LM2904PWRE4 - Dual 26V 700kHz Op Amp | Texas Instruments

Texas Instruments LM2904PWRE4 is a dual general-purpose operational amplifier with two amplifier circuits, a 700 kHz gain-bandwidth product, and operation up to 26 V in an 8-pin TSSOP package. The device supports single-supply or dual-supply operation and provides a 0.3 V/us slew rate. It is packaged for tape-and-reel manufacturing and identified as automotive temperature grade by the manufacturer ordering information. An operational amplifier is an analog signal-processing IC that uses high-gain differential amplification to compare or amplify a voltage. In the broader semiconductor hierarchy, the LM2904 belongs to the operational-amplifier family within analog amplifiers and signal-chain ICs. Its dual-circuit configuration allows two independent amplifier channels in one package, reducing board area when a design needs general-purpose voltage amplification, buffering, or signal conditioning. The principal operating characteristics are its 26 V maximum supply capability, 700 kHz gain-bandwidth product, and 0.3 V/us slew rate. The 8-TSSOP package measures 0.173 inches, or 4.40 mm, in width according to the component listing. Low supply-current operation independent of supply voltage is also identified in the LM2904 datasheet, making the amplifier suitable for power-conscious analog systems that do not require high-speed precision amplification. The LM2904 uses two independent amplifier sections for general-purpose analog functions. Its bandwidth supports moderate-frequency signal processing rather than high-speed video or RF amplification. A designer should verify gain-bandwidth, slew-rate, output-current capability, input common-mode range, input bias current, and output-voltage swing against the application because those operating limits define whether a conventional non-inverting or inverting topology can meet the required waveform and load conditions. Typical uses include low-frequency sensor conditioning, audio preamplification, current-to-voltage conversion, general feedback control, and analog signal buffering. Because the IC contains two amplifiers, a single package can implement an instrumentation-style signal chain, a dual-channel filter, or a mixed configuration such as an active filter followed by an output driver. The 8-pin TSSOP footprint is also practical for compact mixed-signal boards. PCB implementation should provide a short, low-impedance supply path to the device and route sensitive input and feedback connections away from switching nodes. Decoupling capacitors should be placed close to the supply pins, while input and feedback components should be positioned to minimize parasitic capacitance and leakage. Stable operation also depends on keeping output current and capacitive loading within the limits specified by the manufacturer datasheet. This product page organizes the LM2904PWRE4 specifications, practical application guidance, same-package alternatives, and design considerations into an engineering-focused selection resource. It also highlights where additional device parameters must be checked directly in the manufacturer datasheet before a new analog board is released.

RFQ Contact
LM2904PWRG3 - Dual 26V 700kHz Op Amp | Texas Instruments
LM2904PWRG3

LM2904PWRG3 - Dual 26V 700kHz Op Amp | Texas Instruments

The Texas Instruments LM2904PWRG3 is a dual general-purpose operational amplifier rated for a 26 V maximum total supply voltage and a 700 kHz gain-bandwidth product, supplied in an 8-pin TSSOP package. The device contains two independent, internally frequency-compensated amplifiers, allowing one package to provide two separate analog signal-processing channels. Its 0.3 V/us slew rate supports general-purpose applications requiring stable amplification from low-frequency instrumentation signals. An operational amplifier is a voltage-gain semiconductor that uses high open-loop gain and negative feedback to amplify small voltage differences. The dual-amplifier configuration belongs to the broader hierarchy of analog signal-chain ICs, analog ICs, and semiconductors. Operational amplifiers are commonly used in sensor conditioning, current sensing, error amplifiers, voltage followers, filters, and signal-conversion circuits where a predictable closed-loop response is more important than very high speed. The LM2904PWRG3 is designed for cost-sensitive, general-purpose systems rather than precision or high-speed signal-chain applications. According to the Texas Instruments LM2904 product information, the device is specified as a dual 26 V, 700 kHz operational amplifier. The manufacturer documentation also describes the LM2904 family as providing two independent, high-gain, frequency-compensated amplifiers that can operate from a single supply or split supplies. A low 0.7 mA typical supply-current drain is identified in the device documentation, helping reduce system power consumption when both channels remain active. The wide supply-voltage capability makes the amplifier applicable to industrial control, automotive-style signal conditioning, test equipment, and embedded analog interfaces. Each amplifier can be configured with external resistors or capacitors as an inverting amplifier, non-inverting amplifier, voltage follower, comparator-style stage, or active-filter element. Internal frequency compensation removes the need for an external compensation capacitor in ordinary closed-loop configurations, simplifying implementation while preserving stable operation for typical feedback networks. The TSSOP-8 package provides a compact surface-mount footprint suitable for high-density analog boards. Because the device supports single-supply or split-supply operation, the circuit designer must still define the input common-mode range and output swing relative to the selected rails. Input and output voltages must remain within the limits defined by the manufacturer datasheet, and unused amplifier inputs should be biased to prevent undefined operation. This product page combines the verified manufacturer characteristics, package information, sourcing links, application guidance, and drop-in comparison data into an engineering-focused reference. It also highlights where the LM2904PWRG3 is appropriate and where higher precision, wider bandwidth, lower noise, or automotive qualification is required. Review the pin-description table and recommended operating conditions in the manufacturer datasheet before final PCB release or substitution to another dual amplifier.

RFQ Contact
LM2904PWRG4 - Dual 26V 700kHz Op Amp | Texas Instruments
LM2904PWRG4

LM2904PWRG4 - Dual 26V 700kHz Op Amp | Texas Instruments

The Texas Instruments LM2904PWRG4 is a dual general-purpose operational amplifier with a 26 V maximum supply rating, 700 kHz gain-bandwidth product, and an 8-pin TSSOP package. It contains two internally frequency-compensated amplifiers and operates from single or split supplies, making it suitable for cost-sensitive industrial and consumer signal-conditioning designs. An operational amplifier is a high-gain differential amplifier used to compare or amplify small voltage signals. The LM2904 belongs to the operational-amplifier hierarchy, where an op amp forms part of a broader analog and mixed-signal processing system. Its low supply-current consumption, common-mode input range that includes ground, and wide supply-voltage range make it useful in sensor interfaces, buffer stages, audio paths, and low-to-moderate-frequency control loops. The two channels provide approximately 0.3 V/us slew rate, 3 mV typical input offset voltage, 2 nA typical input offset current, and 20 nA typical input bias current. Typical supply-current consumption is 0.7 mA. Internal frequency compensation removes the need for external compensation in conventional closed-loop configurations, while the common-mode range extending toward ground supports direct sensing of signals near the lower supply rail. Each channel can operate independently, allowing simultaneous amplification, filtering, voltage comparison, or buffering. The device includes input-bias-current compensation and differential-input protection through internal clamp structures, supporting operation in conventional industrial control and instrumentation circuits. Designers must still observe the absolute maximum ratings for supply voltage, input voltage, current, junction temperature, and package power dissipation. Typical uses include low-frequency sensor conditioning, 4-20 mA receiver stages, audio preamplification, comparator-based control, active filters, and general-purpose analog interfaces. The dual configuration reduces component count when two independent analog functions are needed, while the compact TSSOP package suits densely assembled control boards. The main design consideration is bandwidth and stability. The 700 kHz gain-bandwidth product and 0.3 V/us slew rate are appropriate for low-frequency precision and general-purpose circuits, but they do not target high-speed signal chains. Check the required closed-loop gain, output swing, load impedance, supply voltage, and input common-mode range against the manufacturer datasheet. This product page combines the device specifications, application guidance, same-footprint alternatives, and engineering-oriented selection considerations. It also identifies where a redesign should focus on supply range, slew rate, precision, or package compatibility rather than treating every dual op amp as an interchangeable replacement.

RFQ Contact
LM2904PWRG4-JF - 26-V Dual Op Amp | Texas Instruments
LM2904PWRG4-JF

LM2904PWRG4-JF - 26-V Dual Op Amp | Texas Instruments

The Texas Instruments LM2904PWRG4-JF is a dual general-purpose operational amplifier with two independent amplifier channels, a 26 V maximum supply rating, and a 700 kHz gain-bandwidth product in an 8-pin TSSOP package. The -JF ordering code identifies the specified Texas Instruments device, while the PW package contains both channels and their power connections in a compact surface-mount outline. An operational amplifier is a high-gain analog building block used in signal-conditioning, comparison, feedback, filtering, and amplification circuits. In the broader electronics hierarchy, an operational amplifier is a type of analog amplifier IC and belongs to the amplifier and signal-processing category. A dual device contains two amplifier sections in one package, allowing one component to handle two related signals while reducing board area and external component count. The LM2904 family is positioned for general-purpose designs rather than precision or high-speed instrumentation. Its stated 700 kHz gain-bandwidth product gives designers a concrete basis for estimating closed-loop bandwidth at a selected noise gain. The 26 V maximum supply rating provides compatibility with higher-voltage analog systems, while the -40°C to +125°C temperature range supports industrial temperature-range design requirements. Each amplifier can operate with feedback configured for inverting, non-inverting, summing, and other standard analog topologies. Differential input and feedback arrangements determine voltage gain and signal behavior, so the same device can serve as a signal amplifier, comparator when configured for saturation, or an active filter building block. The dual channel count is especially useful when a circuit requires two closely related signal paths, such as a sensor front end and a buffered reference stage. Typical applications include sensor-signal conditioning, control-loop error amplification, audio preamplification, low-frequency active filtering, and general instrumentation. The 700 kHz gain-bandwidth product is most relevant to low-to-moderate-bandwidth closed-loop designs, while the 26 V supply rating is useful when the signal path operates from a higher-voltage rail. Design the surrounding feedback network carefully because resistor and capacitor tolerances directly influence gain, bandwidth, offset behavior, and stability. Decoupling capacitors should be placed close to the supply pins, and unused amplifier inputs must be biased so they do not float. The TSSOP-8 outline also requires adequate solder-joint formation and thermal spreading for reliable assembly. This product page combines the exact ordering information, principal electrical ratings, package details, drop-in replacement guidance, comparison rows, and application-specific design considerations to support faster component selection and board planning.

RFQ Contact
LM2904Q2T - Dual 1.1 MHz Op Amp | STMicroelectronics
LM2904Q2T

LM2904Q2T - Dual 1.1 MHz Op Amp | STMicroelectronics

STMicroelectronics LM2904Q2T is a low-power dual bipolar operational amplifier containing two independent, internally frequency-compensated amplifiers. Each channel provides a 1.1 MHz gain-bandwidth product, 0.6 V/us slew rate, and approximately 100 dB open-loop gain. The device operates from 3 V to 30 V and is supplied in an 8-pin DFN package measuring 2 mm by 2 mm, making it suitable for compact, general-purpose analog signal-processing systems. An operational amplifier is an active analog semiconductor that compares two input voltages and drives its output toward the higher-voltage input. In negative-feedback configurations, it amplifies differential signals while maintaining high input impedance and low output impedance. The LM2904Q2T belongs to the operational-amplifier hierarchy: dual amplifier, voltage-feedback amplifier, analog IC, and semiconductor. Two independent channels allow one package to implement two separate signal paths. Key characteristics include a 1.1 MHz gain-bandwidth product, a 0.6 V/us slew rate, approximately 100 dB gain, and low-power bipolar operation. The manufacturer's listed input-current characteristics include 20 nA and 2 nA. Internal frequency compensation simplifies closed-loop amplifier selection, allowing common gains to be implemented without external compensation components. A wide 3 V to 30 V operating range also supports both conventional 5 V analog systems and higher-voltage industrial rails. The two amplifiers operate independently, which prevents signal or output interaction between channels except through their shared supply connections. Both channels use single-ended outputs and share internal frequency compensation. This architecture is appropriate for general-purpose voltage amplification, impedance buffering, comparison, instrumentation, and feedback-control blocks where moderate bandwidth and supply flexibility are more important than low-noise precision or rail-to-rail output operation. Typical applications include sensor-signal conditioning, industrial transducer interfaces, analog control loops, audio preamplifier stages, voltage buffering, and general instrumentation. In a 2 x 2 mm DFN package, the device can reduce board area in designs that can accommodate a land pattern without an exposed thermal pad and maintain adequate copper and assembly process capability. Design with the LM2904Q2T by verifying input common-mode range, output swing, supply current, and capacitive-load stability against the operating point. Keep sensitive-input and feedback routes short, place input and output bypass capacitors close to their associated supply pins, and follow the manufacturer's layout and soldering guidance for the small-pitch DFN footprint. This page combines the exact LM2904Q2T ordering information with electrical characteristics, package constraints, application guidance, a same-package replacement assessment, and practical selection criteria. It also distinguishes confirmed drop-in compatibility from broader functional equivalents so engineers can make footprint-aware design decisions without treating similar amplifier specifications as guaranteed interchangeability.

RFQ Contact
LM2904QD - Dual 26V 700kHz Automotive Op Amp | Texas Instruments
LM2904QD

LM2904QD - Dual 26V 700kHz Automotive Op Amp | Texas Instruments

Texas Instruments LM2904QD is an automotive-grade, dual operational amplifier with a 26 V maximum supply rating, 700 kHz gain-bandwidth product, and an 8-terminal gull-wing SOP package. The device contains two general-purpose amplifier sections, allowing one package to support two independent analog signal paths while reducing board area in automotive electronic-control systems. An operational amplifier is an analog amplifier IC that uses high open-loop gain to amplify voltage differences between its non-inverting and inverting inputs. The LM2904 belongs to the broader hierarchy of operational amplifier, voltage-feedback amplifier, analog IC, and semiconductor. Its dual-channel configuration allows two amplifier sections to be used for signal conditioning, buffering, sensing, or feedback-control functions without adding a second package. The LM2904QD is identified as an automotive temperature-grade variant. Its 26 V supply capability accommodates automotive-style power rails, while the 700 kHz gain-bandwidth product supports general-purpose closed-loop signal amplification at moderate frequencies. The dual architecture also reduces component count in systems that need two equivalent amplifier channels. Operation from a single positive supply is a defining family characteristic, although common-mode range, output swing, offset, and noise figures should be checked against the manufacturer datasheet for the exact operating conditions. The 8-terminal SOP package uses gull-wing leads and a rectangular body, making LM2904QD suitable for conventional through-hole board assembly rather than a compact surface-mount land pattern. Because the automotive suffix denotes a qualified ordering configuration, engineers should confirm the exact qualification, temperature range, marking, and production-test requirements in the Texas Instruments ordering information before release to manufacturing. Typical applications include automotive sensor interfaces, actuator-driver feedback paths, battery-monitoring circuits, instrumentation signal conditioning, and low-frequency control loops. In each case, the two amplifier sections can process complementary or independent signals. The 700 kHz bandwidth is generally more relevant to low-bandwidth sensing and feedback than to high-speed signal processing, so applications requiring wide-band precision or rail-to-rail output should be reviewed separately. The principal design consideration is error budget: input offset voltage, input bias current, common-mode input range, output voltage swing, supply current, and stability with the selected feedback network determine practical accuracy. Decoupling capacitors should be placed close to the supply pins, and unused amplifier inputs should be biased according to the manufacturer’s recommended configuration. PCB layout should preserve a low-impedance ground return and avoid long feedback traces. This page combines the Texas Instruments family specifications, package details, drop-in alternatives, and implementation guidance into an engineering-focused reference. It also identifies which parameters require confirmation in the full manufacturer datasheet, helping designers distinguish confirmed LM2904QD characteristics from application-specific design requirements.

RFQ Contact
LM2904QDR - Dual 26V 700kHz Operational Amplifier | Texas Instruments
LM2904QDR

LM2904QDR - Dual 26V 700kHz Operational Amplifier | Texas Instruments

Texas Instruments LM2904QDR is a dual, general-purpose operational amplifier with two amplifier circuits, a 26 V power-supply rating, and a 700 kHz gain-bandwidth product. The device is offered in an 8-pin SOIC package and is specified for operation from -40 °C to +125 °C. It is intended for instrumentation, buffering, general signal conditioning, and applications requiring two amplifiers in one package. An operational amplifier is an active analog signal-processing component that uses high open-loop gain to amplify the difference between its inverting and non-inverting inputs. Within the broader hierarchy of analog and mixed-signal integrated circuits, the dual operational amplifier combines two amplifier channels with a shared power supply. The LM2904 family is commonly used where economical, general-purpose amplification is needed rather than high-speed, low-noise, or precision performance. The LM2904QDR provides two independent amplifier circuits in one 8-pin SOIC package. Its stated 700 kHz gain-bandwidth product supports general-purpose feedback-based signal amplification, while the 26 V maximum supply rating accommodates conventional industrial and automotive-style supply environments. The dual configuration reduces package count when two amplifier channels are required in the same circuit board area. The operating-temperature range of -40 °C to +125 °C makes the device suitable for temperature-extended industrial equipment, instrumentation, control systems, and vehicle electronics when the surrounding system also meets the required operating limits. The SOIC (D) package also supports conventional surface-mount assembly. Designers should use the manufacturer pin-description table when assigning PCB nets and must account for input common-mode range, output swing, input bias current, noise, and stability requirements in the final signal chain. Typical uses include sensor-signal conditioning, low-frequency transducer amplification, audio preamplification, voltage buffering, loop filtering, and general industrial control interfaces. In a dual instrumentation circuit, one channel can amplify a sensor output while the other provides buffering, gain, or active filtering. Because the amplifier is intended for general-purpose use, its performance should be checked against the accuracy, bandwidth, noise, and common-mode requirements of the application rather than inferred from the maximum supply rating alone. For PCB design, keep the feedback network and input nodes compact, provide normal supply bypassing, and avoid long traces that increase parasitic capacitance or pickup. Check whether the selected gain and capacitive loading require additional compensation. Use the manufacturer datasheet for the complete electrical characteristics, recommended operating conditions, pin functions, and application guidance. This page combines the verified device identity, package information, operating-temperature data, source links, drop-in comparison options, and practical design guidance to support faster component selection and PCB implementation.

RFQ Contact
LM2904QDRG4 - Dual 26 V 700 kHz Op Amp | Texas Instruments
LM2904QDRG4

LM2904QDRG4 - Dual 26 V 700 kHz Op Amp | Texas Instruments

Texas Instruments LM2904QDRG4 is a dual general-purpose operational amplifier designed for industrial and automotive control systems. The device contains two independent, internally frequency-compensated amplifiers, operates from a single supply as high as 26 V, and supports dual supplies of ±13 V. Each channel has a gain-bandwidth product of 700 kHz and a slew rate of 0.3 V/µs, while the typical supply-current drain is 0.7 mA. The specified package is the narrow-body 8-SOIC, supplied tape and reel. An operational amplifier is an analog signal-conditioning IC that uses high open-loop gain and negative feedback to amplify voltage differences. The dual-amplifier configuration places two independent amplifiers in one package, making it useful within the hierarchy of op amp, dual op amp, analog IC, and integrated circuit. Common uses include sensor conditioning, voltage amplification, comparison, and control-loop stages where broad supply-voltage tolerance is valuable. The LM2904QDRG4 is specified for single-supply operation up to 26 V and dual-supply operation at ±13 V. Its common-mode input range includes ground, which allows the device to process signals near the lower supply rail. The internally frequency-compensated architecture simplifies closed-loop design, while the 700 kHz gain-bandwidth product supports general-purpose signal paths rather than high-speed precision applications. The two channels provide independent operation, allowing one channel to perform signal amplification while the other handles feedback, comparison, or monitoring. A 0.3 V/µs slew rate governs large-signal response, and the 0.7 mA typical supply-current drain supports low-power control designs. The 8-SOIC footprint is widely used for industrial and automotive printed-circuit boards, although engineers should verify the exact pin arrangement and exposed thermal requirements in the manufacturer datasheet. Typical applications include automotive sensor interfaces, industrial control loops, low-level signal conditioning, actuator-driver feedback networks, and general dual-amplifier signal paths. The 26 V supply capability is particularly useful when a circuit must operate from a nominal 24 V industrial rail while retaining tolerance for transient excursions, provided the absolute maximum limits are respected. When designing a replacement, verify the channel pinout, supply limits, common-mode range, output-swing limits, and required package dimensions before changing the PCB. Decoupling capacitors should be placed close to the supply pins, and sensitive layouts should minimize parasitic capacitance between input and output nodes to preserve stability. This page combines manufacturer specifications, package information, same-family replacement guidance, comparison parameters, and practical circuit-design considerations. It is intended to help engineers identify an exact-footprint alternative, compare practical constraints, and design the LM2904QDRG4 into industrial or automotive control electronics.

RFQ Contact
LM2904QDRG4Q1 - Dual 26 V AEC-Q100 Op Amp, 700 kHz, SOIC-8 | Texas Instruments
LM2904QDRG4Q1

LM2904QDRG4Q1 - Dual 26 V AEC-Q100 Op Amp, 700 kHz, SOIC-8 | Texas Instruments

The Texas Instruments LM2904QDRG4Q1 is an automotive-grade dual operational amplifier with two independent, internally compensated amplifiers packaged in an 8-pin SOIC (DBV) package. Each channel delivers a 700 kHz gain-bandwidth product, a 0.3 V/us slew rate, and operates from a single supply between 3 V and 26 V. What is a dual operational amplifier? A dual op amp is a single integrated circuit containing two independent, high-gain, frequency-compensated amplifiers. It belongs to the hierarchy: operational amplifier -> analog amplifier IC -> integrated circuit -> semiconductor. The LM2904-Q1 family is the AEC-Q100-qualified automotive version of the industry-standard LM2904, which is one of the most widely cloned and second-sourced general-purpose amplifier footprints in the world. Key electrical features include a low supply-current drain that is independent of supply voltage (0.7 mA typical per amplifier), a common-mode input voltage range that includes ground, and a common-mode rejection ratio of 65 dB. Because the amplifiers are internally compensated, no external frequency-compensation network is required, which simplifies both PCB layout and BOM cost in automotive designs. Internally, each amplifier uses a differential input stage with a class-A output stage that provides good output swing and load-driving capability. The single-supply operation from 3 V to 26 V directly accommodates 12 V battery-derived automotive rails with transient margin, and allows the same part to be used across 5 V, 12 V and 24 V nominal systems without a second part number. Typical automotive applications include body electronics modules, actuator and relay drivers, sensor signal conditioning for resistive sensors, battery monitoring, and low-cost power supply feedback. The same amplifier is equally suited to industrial instrumentation, audio preamplifier stages, and general DC signal conditioning where a cost-optimized general-purpose dual amplifier is preferred over a precision rail-to-rail part. When designing with the LM2904QDRG4Q1, remember that it is a bipolar general-purpose amplifier with input common-mode range that does not reach the positive rail. Place a supply-bypass capacitor of 0.1 uF close to pin 8 and a bulk capacitor near pin 4, and use resistors of 10 kohm or lower in the feedback network to preserve bandwidth. This page consolidates manufacturer specifications, AEC-Q100 qualification details, drop-in SOIC-8 alternatives from Texas Instruments and STMicroelectronics, and practical layout guidance that is not collected in one place on a distributor listing.

RFQ Contact
LM2904QDRQ1 - Dual 26V 700kHz Op Amp AEC-Q100 | TI
LM2904QDRQ1

LM2904QDRQ1 - Dual 26V 700kHz Op Amp AEC-Q100 | TI

The Texas Instruments LM2904QDRQ1 is an automotive-grade, dual operational amplifier qualified to AEC-Q100, operating from a single supply of 3V to 26V (or dual supplies plus/minus 1.5V to plus/minus 13V) with a 700 kHz gain-bandwidth product in an 8-pin SOIC (D) package rated -40C to +125C. An operational amplifier (op amp) is a high-gain differential-input voltage amplifier and a fundamental analog building block within the signal-chain hierarchy: op amp -> amplifier IC -> analog/mixed-signal IC -> semiconductor. A dual op amp integrates two independent amplifiers in one package, cutting board space and BOM cost for multi-channel signal conditioning. Key features include a low 500 uA supply current per amplifier, a common-mode input range that includes ground (enabling true single-supply operation), internal frequency compensation, and output short-circuit protection. ESD protection exceeds 500 V per MIL-STD-883 Method 3015 and 200 V on the machine model, per the TI datasheet. Technically, the bipolar process yields a typical 2 mV input offset voltage (7 mV max) and 20 nA typical input bias current. The 0.3 V/us slew rate and 700 kHz GBW suit low-frequency sensor and control loops; the output swings close to the negative rail but is not rail-to-rail. Operation remains stable with moderate capacitive loads. Typical applications include automotive sensor signal conditioning (temperature, pressure, position), current sensing, active filters, DC motor control, and battery management front-ends, where the 26V rating allows direct operation from a 12V automotive battery rail with load-dump headroom. Design tip: decouple VCC with a 0.1 uF ceramic close to pin 8, keep the input common-mode below VCC-1.5V, and buffer high-impedance sources to limit offset errors. For new automotive designs requiring 36V ratings and tighter offset, consider the next-generation LM2904B-Q1 family.

USD $0.22 Contact
LM2904QM8-13 - 36 V Dual Op Amp | Diodes Incorporated
LM2904QM8-13

LM2904QM8-13 - 36 V Dual Op Amp | Diodes Incorporated

The Diodes Incorporated LM2904QM8-13 is an automotive-compliant, dual general-purpose operational amplifier with a 36 V total supply rating and an 8-pin MSOP package. It combines two amplifier channels, 500 uA supply current, 20 nA input offset current, and 100 dB open-loop gain into an industry-standard surface-mount format. The LM2904QM8-13 is designed for signal conditioning, analog measurement, and control circuits operating from dual or single-ended supplies. An operational amplifier is a high-gain analog building block that compares an input voltage with a feedback voltage and drives its output to reduce the difference between them. In the signal-conditioning hierarchy, the LM2904QM8-13 belongs to the general-purpose operational-amplifier class, a type of analog amplifier used in instrumentation, sensor interfaces, active filters, and closed-loop control. Its dual-channel configuration allows two amplifier functions in one package while reducing board area. The main features of this device include two amplifier circuits, a 36 V maximum total supply voltage, 500 uA supply current, 20 nA input offset current, and 100 dB open-loop gain. The automotive-compliant construction identifies it for applications requiring a higher-reliability general-purpose amplifier. Its MSOP-8 package supports compact PCB layouts, while the -13 ordering suffix identifies tape-and-reel production packaging. The manufacturer describes the LM2904Q family as automotive-compliant dual and quad operational amplifiers, with industry-standard pinouts and green mold compound. The LM2904Q and LM2904AQ devices are offered in SO-8, TSSOP-8, and MSOP-8 packages. This package compatibility gives engineers a familiar circuit implementation, while the dual topology simplifies circuits requiring one signal-conditioning channel and one feedback or drive channel. Typical uses include low-side current sensing, transducer amplification, active filtering, comparator-style signal conditioning, and general industrial control. In current-sensing applications, the amplifier compares a scaled voltage across a shunt with a reference. In sensor interfaces, it amplifies small voltage changes around a common-mode level. In active filters, its gain-bandwidth behavior and open-loop gain define the operating point when combined with external resistors and capacitors. For a new layout, verify the MSOP-8 pin assignment and orient the exposed package according to the manufacturer datasheet before assigning input, output, supply, and feedback connections. Decoupling capacitors should be placed close to the supply pins, and sensitive input traces should be kept away from switching nodes and high-current paths. The 36 V rating is a maximum operating limit rather than a recommended supply condition. This page organizes the verified device characteristics, package information, application guidance, and same-family replacement candidates into a practical engineering reference. It also highlights where a new design should consult the manufacturer datasheet for detailed electrical limits, test conditions, pin definitions, and qualification criteria.

RFQ Contact
LM2904QP - Dual 26V 700kHz Op-Amp TSSOP-8 | Texas Instruments
LM2904QP

LM2904QP - Dual 26V 700kHz Op-Amp TSSOP-8 | Texas Instruments

The Texas Instruments LM2904QP is a dual general-purpose operational amplifier rated for 26 V supply operation with a 700 kHz gain-bandwidth product, housed in an 8-pin TSSOP (PW) package. As a Q-suffix automotive-grade variant, it is AEC-Q100 qualified and specified from -40C to +125C, making it suited to vehicle and harsh-environment electronics. A dual operational amplifier is an integrated circuit that packs two independent, internally frequency-compensated op amps onto a single silicon die within one package. Op amps are the foundational building blocks of the analog signal chain, sitting within the broader hierarchy of amplifier ICs, linear ICs, and semiconductors, and they perform amplification, buffering, filtering, comparison, and level shifting in virtually every electronic system. Key features of the LM2904QP include operation from a single supply or dual supplies, a low supply-current drain of approximately 0.7 mA typ that is largely independent of supply voltage, and a common-mode input voltage range that includes ground, allowing direct sensing of signals near 0 V in single-supply systems. The two channels are closely matched, reducing board space versus discrete single-channel amplifiers. Technically, the LM2904 family uses internally compensated bipolar technology, which guarantees unity-gain stability without external compensation components. The ground-inclusive input common-mode range and single-supply capability eliminate the need for a negative rail in low-side sensing applications, while the 700 kHz bandwidth covers audio, low-speed control loops, and general industrial signal conditioning. Low input bias and offset currents minimize error in high-impedance source applications. Typical applications include automotive sensor signal conditioning, low-side current sensing, active filters, transducer amplifiers, and battery-powered industrial instrumentation, where single-supply operation near ground and wide temperature tolerance are essential. Design consideration: the output cannot swing rail-to-rail, so allow headroom on both rails and verify the output swing specification in the manufacturer datasheet against your signal range, especially at elevated temperature and light load. This page synthesizes the manufacturer product data, drop-in alternatives, comparison tables, and practical design notes in one place, providing engineering context beyond a raw parametric listing.

RFQ Contact
LM2904QPWRG4Q1 - 26V Dual Op Amp | Texas Instruments
LM2904QPWRG4Q1

LM2904QPWRG4Q1 - 26V Dual Op Amp | Texas Instruments

Texas Instruments LM2904QPWRG4Q1 is an automotive-grade, dual general-purpose operational amplifier with two independent amplifiers, a 26 V maximum supply rating, and a 700 kHz gain-bandwidth product. The device is packaged in an 8-pin TSSOP (PW) package and is qualified to AEC-Q100 specifications for automotive applications. An operational amplifier is a high-gain, frequency-compensated analog building block used to amplify sensor signals, control feedback loops, buffer voltage references, and perform general signal conditioning. The LM2904 belongs to the dual operational-amplifier hierarchy and combines low supply-current consumption with a wide common-mode input range that includes ground, making it suitable for single-supply systems operating near the lower rail. The dual configuration provides two amplifiers in one package, reducing board area when a design needs matched general-purpose stages. Key characteristics include a 700 kHz gain-bandwidth product, a 0.3 V/µs slew rate, and a typical low supply-current drain of 0.7 mA per amplifier. Its AEC-Q100 qualification supports automotive-grade applications where temperature robustness and production quality requirements are important. Internally, the device contains two independent, high-gain, frequency-compensated amplifiers. Frequency compensation allows operation without external compensation, while the ground-referenced common-mode capability is valuable for sensing small signals produced by sensors, resistive dividers, and single-supply analog circuits. The 26 V maximum rating also provides headroom for industrial and automotive supply environments. Typical uses include low-side current sensing, sensor-signal conditioning, actuator feedback, automotive interface electronics, and general dual-amplifier signal conditioning. Because both channels are independent, one package can support two related functions, such as signal amplification and an active filter, without requiring separate single amplifier packages. Designers should maintain input and output voltage limits, account for input common-mode range, and provide stable feedback-network layouts around the device. Decoupling capacitors should be placed close to the supply pins, while sensitive input and feedback nodes should be kept away from switching-current paths. The automotive qualification does not replace application-level validation of transient immunity, noise, and thermal performance. This page organizes the device specifications, qualified family information, package details, practical design guidance, and qualified same-footprint alternatives into an engineering-focused selection resource for analog and automotive power-management designs.

RFQ Contact
LM2904QPWRQ1 - Dual 26V 700kHz AEC-Q100 Op Amp | Texas Instruments
LM2904QPWRQ1

LM2904QPWRQ1 - Dual 26V 700kHz AEC-Q100 Op Amp | Texas Instruments

Texas Instruments LM2904QPWRQ1 is an AEC-Q100-qualified, dual operational amplifier with a 26 V power-supply rating and 700 kHz gain-bandwidth product. The device contains two general-purpose amplifiers in an 8-pin TSSOP package, making it suitable for automotive signal-conditioning, instrumentation, sensor-interface, and industrial control circuits. Its dual-channel architecture also allows one package to provide gain, filtering, buffering, or differential amplification in two related signal paths. An operational amplifier, or op amp, is a voltage-controlled differential amplifier whose open-loop gain is shaped by external feedback components. Op amps belong to the broader amplifier IC and analog-signal-processing hierarchy. They are widely used because a feedback network can set closed-loop gain, improve impedance characteristics, and enable stable implementations of common analog functions using resistors and capacitors. The LM2904-Q1 family provides the established LM2904 operating characteristics in an automotive-qualified configuration. Key headline features include two amplifier channels, operation from a 26 V-rated supply, a 700 kHz gain-bandwidth product, and AEC-Q100 qualification. The manufacturer identifies the device as an industry-standard dual operational amplifier for automotive applications, where qualification supports controlled introduction into automotive electronic systems. Its 700 kHz bandwidth makes the amplifier suitable for moderate-speed precision signal paths rather than high-frequency RF or video amplification. The dual architecture reduces package count when two independent gain or filtering stages are required. This is particularly useful in sensor interfaces, actuator drivers, battery-monitoring circuits, and automotive control modules where board area and component count affect reliability. Typical applications include automotive sensor conditioning, low-side current measurement, transducer amplification, voltage buffering, and general-purpose analog signal processing. The high supply-voltage capability can simplify interfaces to automotive battery-derived rails, although designers must still observe the datasheet limits for input common-mode range, output swing, supply current, and thermal conditions. A primary design consideration is that the TSSOP package has limited thermal dissipation capability. Follow the manufacturer datasheet for input and output voltage limits, common-mode behavior, electrical characteristics, and application guidance. Place bypassing capacitors close to the supply pins, preserve the recommended feedback topology, and verify common-mode and output-swing limits across the complete operating range. This product page combines the manufacturer specification summary, automotive qualification information, package details, verified source links, application guidance, and a compatibility-oriented comparison framework. That engineering context helps distinguish the LM2904QPWRQ1 from lower-voltage modern op amps, higher-bandwidth alternatives, and non-automotive versions before a PCB or BOM decision is made.

RFQ Contact
LM2904QS-13 - 36V Dual Op Amp, 1.1MHz | Diodes Incorporated
LM2904QS-13

LM2904QS-13 - 36V Dual Op Amp, 1.1MHz | Diodes Incorporated

Diodes Incorporated LM2904QS-13 is an automotive-compliant dual operational amplifier packaged in an 8-pin SO-8 package. The device operates from a 36 V maximum supply, provides two amplifier channels, and combines a 1.1 MHz gain-bandwidth product with 100 dB open-loop gain. Its 500 uA quiescent current and 20 nA typical input bias current suit low-power analog signal chains that require higher voltage tolerance than conventional low-voltage amplifier families. An operational amplifier, commonly called an op amp, is a high-gain differential amplifier whose closed-loop behavior is defined primarily by external feedback components. Within the semiconductor hierarchy, the LM2904QS-13 belongs to the operational amplifier, analog amplifier IC, and power-management-supporting signal-conditioning categories. It can amplify sensor outputs, implement active filters, buffer voltage references, and perform general-purpose analog conditioning where a wide supply range and dual-channel integration are useful. Key characteristics include two independent amplifier circuits, a 36 V maximum supply, 1.1 MHz unity-gain bandwidth, 100 dB open-loop gain, 500 uA quiescent current, and a typical input bias current of 20 nA. These characteristics make the part appropriate for industrial control, instrumentation, automotive electronics, and appliance applications where two channels can reduce component count and board space. The automotive-compliant LM2904Q family is also manufactured with green mold compound as standard. The LM2904 architecture supports single-supply operation as well as conventional dual-supply operation when negative supply voltage is available. Input and output common-mode limits must remain within the operating boundaries stated in the manufacturer datasheet. Because the amplifier is intended for broad-voltage applications, designers should distinguish the 36 V maximum supply rating from the usable output-swing and input-common-mode ranges; those ranges are not determined by the maximum supply alone. Typical applications include sensor conditioning, current-loop receivers, active low-pass filters, audio and communications blocks, automotive electronics, industrial control modules, and general analog signal-conditioning boards. Two integrated channels are especially useful when a design requires closely related positive and negative signals, such as differential sensor outputs, dual-axis sensing, or paired audio paths. Local decoupling and careful trace routing remain important because high-gain amplifiers can amplify noise, oscillation, and unintended feedback caused by poor layout. For stable operation, place the power-supply bypass capacitor close to the supply pins, keep feedback components compact, and route output signals away from high-impedance input nodes. Avoid placing long copper traces beneath the amplifier unless the layout specifically supports the intended thermal and electrical behavior. Check the complete pin assignment and exposed-package details against the manufacturer datasheet before finalizing a footprint or assembling a prototype. This product page combines the LM2904QS-13 package and electrical identity, verified manufacturer documentation, same-footprint replacement guidance, application-specific engineering notes, and a parameter comparison intended to accelerate component selection. The primary decision factors are SO-8 footprint compatibility, supply voltage, unity-gain bandwidth, input bias current, quiescent current, and automotive qualification requirements.

RFQ Contact
LM2904QTH-13 - Dual 36V Automotive Op Amp | Diodes Incorporated
LM2904QTH-13

LM2904QTH-13 - Dual 36V Automotive Op Amp | Diodes Incorporated

Diodes Incorporated LM2904QTH-13 is a dual general-purpose operational amplifier designed for automotive electronics. It contains two independent high-gain amplifiers in an 8-pin TSSOP package, operates from a single supply up to 36 V or from dual supplies up to ±18 V, and is identified as AEC-Q100 compliant. Key characteristics include a 700 kHz gain-bandwidth product, 0.3 V/µs slew rate, 7 mV input-offset voltage, 250 nA input-bias current, and approximately 700 µA supply current. An operational amplifier is a high-gain analog signal-conditioning IC that compares an input voltage with a feedback reference and drives its output to reduce the difference between them. The LM2904 dual-amplifier configuration belongs to the operational-amplifier family within analog ICs and analog signal-processing semiconductors. Its two channels may be used independently for signal conditioning, voltage comparison, feedback control, or other general-purpose analog functions. The LM2904QTH-13 combines relatively wide supply-voltage tolerance with low quiescent current and automotive-compliant construction. A 36 V maximum supply makes it useful in systems operating from industrial or automotive batteries after appropriate transient and protection design. Its 700 kHz gain-bandwidth product is adequate for low-to-moderate-frequency signal paths, while the 0.3 V/µs slew rate affects how quickly the output can follow large voltage changes. The 40 mA output-current figure and 250 nA input-bias current define important loading and input-stage constraints. The two amplifiers provide flexibility within one compact package, reducing component count in dual-channel circuits. Each channel has its own differential input and output pins, allowing simultaneous or independent operation. Because the device is intended for general-purpose amplification, its offset voltage, input-bias current, bandwidth, and output-drive capabilities must be checked against the target signal amplitude, source impedance, load, noise requirements, and stability conditions. Typical applications include automotive sensor conditioning, actuator and valve-driver feedback, battery-powered instrumentation, industrial control modules, current monitoring, and low-frequency signal amplification. In battery-powered systems, the approximately 700 µA supply-current characteristic helps limit standing power when both channels are operating at low utilization. For high-impedance sensors, the 250 nA input-bias current should be compared with the sensor's effective source impedance and resulting offset error. The main design consideration is maintaining stability with the output load and compensation network selected for the target feedback topology. Keep sensitive input traces away from power paths and output nodes, provide local supply bypassing, and account for automotive supply transients at the board interface. The TSSOP-8 outline also requires thermal analysis when both channels drive demanding loads at elevated ambient temperature. This product page combines the manufacturer and distributor characteristics for the LM2904QTH-13 with package, replacement, application, and design guidance. It highlights practical distinctions among same-footprint alternatives and identifies the electrical details that require confirmation against the current manufacturer datasheet before production release.

RFQ Contact
LM2904S-13 - Dual 1.1MHz Op Amp, 100dB Gain | Diodes
LM2904S-13

LM2904S-13 - Dual 1.1MHz Op Amp, 100dB Gain | Diodes

The Diodes Incorporated LM2904S-13 is a dual general-purpose operational amplifier packaged in an 8-pin SO package. It provides two independent amplifier channels, a listed gain bandwidth product of 1.1 MHz, a listed open-loop gain of 100 dB, and input bias current of 20 nA. The device is intended for single-supply or split-supply operation across industrial temperature conditions. An operational amplifier is a high-gain, differential-input analog amplification component used to compare or amplify voltage signals. Within the electronics hierarchy, the LM2904 belongs to the operational-amplifier family, which sits within analog amplifier ICs and broader semiconductor signal-conditioning products. Its two-channel configuration allows one device to implement two related analog functions while reducing the number of components required on a circuit board. The manufacturer datasheet identifies the LM2902 and LM2904 series as low-input-offset-voltage amplifiers designed for single power-supply operation over a wide voltage range, with split-supply operation also possible. The operating-temperature characterization extends from -40°C to +125°C. The standard green mold compound, industry-standard pinout, and SO-8 packaging support use in conventional industrial, instrumentation, control, and signal-conditioning equipment. The 1.1 MHz gain bandwidth product makes the device appropriate for low-frequency amplification rather than high-speed signal processing. Its 100 dB open-loop gain provides substantial nominal gain before feedback and saturation limits are considered. The 20 nA input bias-current listing is also relevant when the source impedance is high, because bias-current error can become significant relative to the input voltage being measured. Typical uses include transducer-signal conditioning, feedback networks in control systems, active filtering, sensor amplification, and general-purpose analog signal conditioning. Two amplifiers in one package are useful when a design needs an inverting stage and a non-inverting stage, two sensor channels, or an amplifier paired with a comparator-like buffer function. Designers should verify input common-mode range, output swing, output-current capability, offset voltage, and supply-current limits in the manufacturer datasheet before finalizing a new board. Decoupling capacitors should be placed close to the supply pins, and unused amplifier inputs must be biased so that both output stages remain in a defined operating state. This product page combines the manufacturer family data with practical application guidance, a same-package family alternative, and engineering-focused selection criteria. It is intended to help engineers determine whether the LM2904S-13 is appropriate for a low-frequency, dual-amplifier design before moving to detailed electrical verification and PCB implementation.

RFQ Contact
LM2904ST Low-Power Dual Op Amp | STMicroelectronics
LM2904ST

LM2904ST Low-Power Dual Op Amp | STMicroelectronics

STMicroelectronics LM2904ST is a low-power dual operational amplifier packaged in an 8-pin MiniSO package. It contains two independent, internally frequency-compensated amplifiers, allowing one device to implement two separate analog signal-processing channels. The LM2904 family is intended for general-purpose applications where a dual amplifier, low power consumption, and straightforward circuit implementation are more important than low-noise or high-speed performance. An operational amplifier is an active semiconductor device that compares two input voltages and drives its output to amplify the difference between them. In a closed-loop configuration, negative feedback causes the output to follow the intended circuit function with very high input impedance and relatively low output impedance. The LM2904 belongs to the operational-amplifier hierarchy, where it sits below precision amplifiers, rail-to-rail amplifiers, and high-speed amplifiers while remaining appropriate for industrial control, sensor conditioning, audio, and general instrumentation. The LM2904ST provides two amplifier channels in one package, reducing component count and PCB space compared with two separate single-channel amplifiers. Its internally implemented frequency compensation simplifies circuit design by eliminating the need for external compensation components in standard closed-loop applications. Because both channels are independent, the device can support different signal paths, provided the designer observes the common power-supply and grounding requirements. The target LM2904ST is a standard general-purpose dual amplifier in the MiniSO-8 format. The STMicroelectronics LM2904 family also includes other package and performance options, so engineers should compare electrical ratings, temperature range, supply limits, input common-mode range, output swing, and automotive qualification before treating another family member as a drop-in replacement. The exact electrical limits and environmental classifications should be confirmed in the manufacturer datasheet for the selected ordering code. Typical uses include low-frequency sensor signal conditioning, control-loop amplification, active filtering, audio preamplification, transducer interfaces, and general buffer stages. In such circuits, the LM2904ST provides two independently usable channels while keeping the implementation compact. Its internal compensation makes conventional inverting, non-inverting, summing, and differential amplifier configurations straightforward, although output loading, source resistance, stability margins, and the input common-mode range still require careful review. For a new layout, place the device close to the signals it processes, maintain a low-impedance return path to the supply ground, and decouple the supply pins locally. Avoid sensitive-source connections next to the output or supply pins, because parasitic coupling can increase offset and distortion. This product overview combines the manufacturer family information, package identity, pin assignment, sourcing considerations, and drop-in-replacement guidance to support faster engineering selection and PCB planning.

RFQ Contact
LM2904TH-13 - Dual 700 kHz Op Amp | Diodes Incorporated
LM2904TH-13

LM2904TH-13 - Dual 700 kHz Op Amp | Diodes Incorporated

Diodes Incorporated LM2904TH-13 is a dual general-purpose operational amplifier in an 8-pin TSSOP package. The device contains two independent high-gain amplifiers, supports a 700 kHz bandwidth, and is designed for operation from a single supply or from split supplies. The LM2904 family provides a practical choice for signal conditioning, feedback control, and analog circuit designs requiring two amplifiers in one package. An operational amplifier, commonly called an op amp, is a high-gain DC-coupled analog amplifier whose behavior is controlled by feedback around the device. The LM2904 combines two independent amplifier channels in one package, reducing board area compared with two separate single-amplifier devices. Its 8-pin TSSOP package supports compact surface-mount assemblies and exposes supply, input, and output connections for each channel. The most prominent specified characteristics are the two-amplifier configuration, 700 kHz bandwidth, and supply capability extending to ±18 V, equivalent to a 36 V total span. The device is categorized as a standard general-purpose amplifier and is designed for both single-power-supply and split-supply operation. Its architecture also targets low input-offset voltage, making it relevant to closed-loop amplifier and comparator-style signal-processing applications when configured appropriately. The LM2904 series combines independent high-gain operational amplifiers with a broad supply-voltage range. Because the two channels are independent, one channel can process a sensor signal while the other performs an active filter, level conversion, or feedback function. Common-mode and output-voltage limitations still depend on the selected supply voltages, so every analog signal path must remain inside the amplifier’s valid input and output ranges. Typical uses include low-frequency instrumentation, buffered sensor interfaces, audio preamplification, analog gain stages, and dual-axis control loops. The 700 kHz bandwidth is most appropriate for general-purpose signal paths rather than high-speed video, RF, or precision data-conversion applications. Split-supply operation can simplify bipolar signal handling, while single-supply operation may require input and output biasing around the midpoint of the supply. Designers should use the manufacturer’s pin-description and typical-application information to establish channel assignments, bypass-capacitor placement, and acceptable output-load conditions. Decouple each supply rail close to the device, keep feedback paths short, and verify that input common-mode voltage and output swing remain valid over the full supply range and temperature range intended for the design. This page organizes the key device characteristics, practical application guidance, verified pricing references, pin-location information, and same-footprint replacement options. It also distinguishes documented LM2904 family choices from alternatives that would require a different package or different electrical capabilities, helping engineers narrow a redesign without overlooking PCB compatibility.

RFQ Contact
LM2904VDMR2 - Dual 3-32V Op Amp for Industrial Control
LM2904VDMR2

LM2904VDMR2 - Dual 3-32V Op Amp for Industrial Control

The onsemi LM2904VDMR2 is a dual general-purpose operational amplifier with a 3 V to 32 V supply range, 1 MHz gain-bandwidth product, and 8-MSOP package. Designed for low power consumption, the device accepts single-supply or split-supply operation, while its common-mode input voltage range can extend to ground or VEE. It is suited to industrial signal-conditioning, transducer, and analog-control systems. An operational amplifier is a voltage-gain building block used to amplify small signals, buffer sensors, compare voltages, and implement active analog filters. The dual LM2904 family combines two amplifiers in one package, reducing board area compared with separate single amplifiers. Its ability to operate from a single positive supply or from split positive and negative rails gives it broad utility in both grounded-signal systems and bipolar analog environments. Key features include low power drain, a 1 MHz gain-bandwidth product, and a common-mode input range that extends to ground or VEE. The 3 V to 32 V operating range supports both conventional 5 V and 24 V industrial systems when the total supply remains within the rated range. The 8-MSOP surface-mount package also supports compact, high-density analog boards while providing adequate lead spacing for automated assembly and inspection. The LM2904 architecture derives from the circuit design used in onsemi's quad operational-amplifier family. It is intended for general-purpose applications where low power consumption and flexible supply configurations are more important than precision, rail-to-rail input/output performance, or the bandwidth of modern CMOS amplifiers. Because the input common-mode range can reach ground or VEE, the device can process signals near the lower supply rail when correctly biased. Typical applications include 0–5 V or 0–10 V industrial sensor interfaces, low-level transducer amplification, analog alarm and threshold circuits, active low-pass filters, and general control-signal conditioning. It may also be used in battery-powered instrumentation where the selected operating point must balance signal bandwidth against power drain. Split-supply operation is useful for bipolar sensor signals or analog stages that require both positive and negative swing around ground. When designing around the LM2904VDMR2, verify input and output voltage limits at the selected supply voltage and load. Input and output decoupling should be placed close to the device, and unused amplifier channels must be configured according to the manufacturer’s recommended stable operating conditions. Avoid relying on rail-to-rail behavior, and account for input offset and bias-current errors when designing high-accuracy signal chains. This product page consolidates the confirmed supply, bandwidth, package, and application characteristics with drop-in replacement analysis, package comparison, and practical circuit guidance. It helps engineers distinguish genuine footprint-compatible options from amplifiers that are only functionally similar before committing a new board revision.

RFQ Contact
LM2904VDMR2G - Dual 1MHz Op Amp, 3-32V | onsemi
LM2904VDMR2G

LM2904VDMR2G - Dual 1MHz Op Amp, 3-32V | onsemi

onsemi LM2904VDMR2G is a dual general-purpose operational amplifier with two independent channels, 1 MHz gain-bandwidth product, and a 3 V to 32 V supply range in an 8-pin MSOP package. Designed for single-supply or split-supply operation, it accepts input common-mode voltages extending toward ground or VEE, making it suitable for industrial, automotive, battery-powered, and signal-conditioning systems. An operational amplifier is a voltage-feedback amplifier that uses high open-loop gain to compare an input signal with a feedback network. The LM2904 family combines low power consumption, internal frequency compensation, and common-mode input capability reaching ground or VEE. Its dual-channel configuration places two independent amplifiers in one package, reducing component count in applications requiring matched signal paths, sensing, buffering, or error amplification. The principal features are a 3 V to 32 V operating range, approximately 1 MHz gain-bandwidth product, dual-circuit construction, and support for single or split supplies. The common-mode input range is particularly useful in battery systems because the amplifier can operate close to the negative supply rail. Its MSOP-8 package supports compact layouts, while the low-power operating characteristics suit portable and industrial-control equipment. Internally frequency-compensated channels remove the need for an external compensation network in ordinary closed-loop gain configurations. Each channel can operate independently, allowing simultaneous use as two amplifiers. Designers must still observe output-swing, input-voltage, supply-current, and common-mode limits. Configuration as a voltage follower, non-inverting amplifier, or inverting amplifier will determine signal gain and feedback-component values. Typical applications include sensor-interface conditioning, low-side current measurement, industrial control loops, battery-powered monitoring, transducer amplification, and general-purpose analog signal processing. The split-supply capability is useful when bipolar sensor signals must be amplified around ground. In single-supply systems, the ground-reaching common-mode range helps simplify biasing near the lower rail. A key design consideration is to verify output swing under the intended load and to place input and feedback components close to their pins to minimize parasitic pickup. Decoupling capacitors should connect directly between each supply pin and ground. Stable operation should be confirmed across supply voltage, temperature, output loading, and the selected gain because the internal compensation does not remove all application-level stability constraints. This page combines electrical characteristics, package information, drop-in alternatives, comparison parameters, and practical circuit guidance to accelerate component selection. It supports engineers comparing general-purpose dual amplifiers for industrial, automotive, and low-voltage analog systems while emphasizing the need to verify exact pinout, qualification, and operating limits before substitution.

RFQ Contact
LM2904VDR2G - Dual 1MHz Op Amp | onsemi | Industrial
LM2904VDR2G

LM2904VDR2G - Dual 1MHz Op Amp | onsemi | Industrial

The onsemi LM2904VDR2G is a dual, general-purpose operational amplifier with a 1 MHz gain-bandwidth product, 0.6 V/µs slew rate, and operation from single or split supplies in an 8-SOIC package. It is designed for instrumentation, signal conditioning, buffer amplification, and general analog control applications where two amplifiers are required in one package. An operational amplifier is an analog integrated circuit that uses high open-loop gain and negative feedback to amplify a voltage difference. The LM2904 family belongs to the operational-amplifier hierarchy, with the LM358 family representing one-half of a quad amplifier. Its common-mode input range extends to ground or VEE, allowing useful operation in single-supply circuits where the input signal approaches the negative supply rail. Key features include two amplifier circuits per package, a 1 MHz gain-bandwidth product, a 0.6 V/µs slew rate, and a specified operating voltage range of up to ±16 V, equivalent to 32 V across the supply rails. The low-power design supports both single-supply and split-supply operation. The standard 8-SOIC package also simplifies assembly in designs that do not require a high-performance precision amplifier. The LM2904 architecture is intended for general-purpose amplification rather than rail-to-rail input or output operation. Its common-mode input behavior reaches ground or VEE, making it particularly useful for circuits powered from a positive rail and ground. As with any feedback amplifier, stable operation depends on suitable compensation, output loading, source impedance, and the selected gain network. Typical uses include buffering sensor outputs, amplifying low-level analog signals, conditioning potentiometer inputs, driving moderate loads, building active filters, and providing general-purpose gain stages in industrial or embedded systems. Two amplifiers in one SOIC package can also simplify layouts where matched general-purpose stages are needed. When designing around the LM2904, check the common-mode input range and output swing at the intended load rather than assuming rail-to-rail behavior. Place input and feedback components close to the device, provide adequate bypassing near the supply pins, and verify stability at the lowest planned gain. The manufacturer datasheet should guide compensation, load capability, and absolute maximum ratings. This product page combines the exact LM2904VDR2G package and electrical identity with practical design guidance, pin-level information, verified source links, and a package-matched replacement comparison. These engineering details help buyers distinguish the dual general-purpose amplifier from single-amplifier, automotive-qualified, and other LM-family variants before committing to a PCB design.

RFQ Contact
LM2904VN - Dual Op Amp, 1MHz GBW, PDIP-8 | onsemi
LM2904VN

LM2904VN - Dual Op Amp, 1MHz GBW, PDIP-8 | onsemi

The onsemi LM2904VN is a single-supply dual operational amplifier featuring two independent general-purpose op-amp circuits with a 1 MHz gain-bandwidth product, a 0.6 V/us slew rate, and operation from a 3 V to 26 V supply (up to 32 V total, or +/-1.5 V to +/-16 V split supplies), housed in an 8-pin PDIP (0.300 inch, 7.62 mm) through-hole package. A dual operational amplifier integrates two matched, frequency-compensated op-amp cores on a single silicon die within one package. As a subcategory of the linear amplifier family, general-purpose op-amps sit within the broader hierarchy of voltage amplifiers and analog signal-conditioning ICs, providing gain, buffering, filtering, and comparison functions in analog front ends. The dual configuration halves board space and improves channel-to-channel matching compared with two single op-amps. Key features include low power drain, a common-mode input voltage range that extends to ground/VEE (input common-mode includes the negative rail), and single-supply or split-supply operation. These characteristics let designers build ground-referenced signal conditioning directly from a single positive rail without a negative supply, which is the defining advantage of the LM358/LM2904 amplifier family. Technically, the LM2904VN derives from the circuit design perfected for the industry-standard LM324 quad op-amp: the LM358 series is equivalent to one-half of an LM324. The amplifier delivers approximately 70 dB of open-loop gain, low input bias current (about 45 nA typical per distributor characterization data), and internal frequency compensation that guarantees unity-gain stability without external components. Typical applications include transducer amplifiers, DC gain blocks, active filters, comparators, and general low-frequency signal conditioning in industrial controls, automotive subsystems, and battery-powered instruments. A key design consideration: the output stage is not rail-to-rail and can sink only limited current near ground, so loading the output with a resistor to VEE (for example, 2 kOhm) improves output swing close to the negative rail. This page adds value beyond the manufacturer datasheet by consolidating drop-in cross-references, a parameter comparison table against pin-compatible alternatives, and practical design notes in one place.

RFQ Contact