Products (44,000+)

LM324ADRG4 - 1.2MHz Quad Op Amp, 14-SOIC | Texas Instruments
LM324ADRG4

LM324ADRG4 - 1.2MHz Quad Op Amp, 14-SOIC | Texas Instruments

Texas Instruments LM324ADRG4 is a standard general-purpose, four-circuit operational amplifier in a 14-pin SOIC package. Each circuit has a 1.2 MHz gain-bandwidth product, 0.5 V/us slew rate, and operation from single or split supplies over a ±1.5 V to ±16 V range. The four amplifiers are independent, high-gain, frequency-compensated stages designed for general-purpose signal conditioning. An operational amplifier is an amplifier IC used within a feedback network to control gain, amplify differential signals, buffer inputs, perform comparisons, or drive analog stages. The LM324 belongs to the operational-amplifier hierarchy, which includes amplifier ICs, analog signal-chain ICs, and semiconductor devices. Its ability to operate from a single supply makes it useful in battery-powered, industrial-control, instrumentation, and consumer circuits where one supply rail is more practical than split bipolar rails. The LM324 family's key characteristics include a typical supply-current drain of 0.8 mA and a common-mode input-voltage range that includes ground. These characteristics support low-power analog designs where the input signal may approach the lower supply rail. Each amplifier is frequency compensated, reducing the external compensation components normally required in precision applications. The 1.2 MHz bandwidth is sufficient for general-purpose audio, control, sensing, and signal-shaping stages but is not intended for high-speed data acquisition or demanding wideband filtering. Typical uses include current sensing around a low-side shunt, low-side transistor control, sensor amplification, audio channels, and general-purpose buffering. The 14-SOIC package provides a conventional through-hole-compatible footprint for PCB assembly. Because each of the four amplifier sections is independent, unused sections should be configured according to the manufacturer's recommended practice rather than left floating. A key design consideration is the input common-mode range. The LM324 can accept inputs that include ground, making it suitable for many single-supply circuits, but it cannot swing all the way to the positive supply rail. Output swing, load capability, and input bias behavior must therefore be checked against the actual signal range. Decoupling should follow the manufacturer circuit recommendations, with short supply traces and a local bypass capacitor helping maintain stable operation. This product record combines the verified LM324ADRG4 electrical ratings, package information, sourcing links, pin-compatible family options, and practical design guidance. It also distinguishes true same-footprint alternatives from related amplifier families that differ in electrical behavior, qualification, package, or pin assignment.

RFQ Contact
LM324ADTB - Quad 3-32V General-Purpose Op Amp | onsemi
LM324ADTB

LM324ADTB - Quad 3-32V General-Purpose Op Amp | onsemi

onsemi LM324ADTB is a low-cost, general-purpose quad operational amplifier with true differential inputs, four amplifier circuits, a 3 V to 32 V supply range, and 3 mV input offset voltage in a 14-pin TSSOP package. The device is designed for instrumentation, buffer-amplifier, and general signal-conditioning applications where four amplifiers are integrated in one package. An operational amplifier is an analog integrated circuit that uses high-gain differential feedback to amplify the voltage difference between its two inputs. The LM324 belongs to the quad operational amplifier hierarchy: operational amplifier, voltage-feedback amplifier, analog signal-conditioning IC, and power-management IC. Its four independent channels can perform amplification, buffering, summing, comparison, and basic active-filter functions without requiring four separate packages. The LM324ADTB supports single-supply operation from 3 V to 32 V, making it suitable for systems whose rails are higher than those of common rail-to-rail precision amplifiers. Its 3 mV input offset voltage supports general-purpose applications where input accuracy requirements are moderate. True differential inputs allow each channel to respond to the difference between its inverting and non-inverting signals. The integrated quad configuration also reduces board area and simplifies multi-channel routing. As a general-purpose amplifier, the LM324 series emphasizes practical utility rather than high speed or precision. The manufacturer describes the devices as low-cost quad operational amplifiers that are especially useful in single-supply systems. Their quiescent current is approximately one-fifth that of conventional dual operational amplifiers, according to the manufacturer datasheet. Detailed gain-bandwidth, slew-rate, input-bias-current, and common-mode limits must be checked against the operating conditions before precision filtering or signal-chain use. Typical applications include four-channel sensor conditioning, transducer buffering, audio preamplification, current-voltage conversion, DC signal amplification, and mixed-signal instrumentation. The 14-pin TSSOP package is useful for compact industrial, consumer, and communications equipment where four analog functions must be accommodated without using four separate amplifier packages. Supply bypassing and stable feedback layouts remain important at the board level. For a new design, place the device close to the powered circuits it serves and connect a suitable bypass capacitor near the supply pins. Keep feedback resistors and input traces short, maintain symmetrical routing where practical, and account for input bias-current errors when using high source impedances. The single supply must remain within the 3 V to 32 V operating range under all tolerance, transient, and temperature conditions. This page consolidates the LM324ADTB electrical ratings, package details, pin assignments, replacement options, and practical layout considerations into an engineering-focused reference. It also identifies where the general-purpose LM324 architecture is appropriate and where precision, speed, rail-to-rail operation, or a lower-offset amplifier would provide a better design choice.

RFQ Contact
LM324ADTBG - 4-Channel 3-32V Op Amp | onsemi | TSSOP-14
LM324ADTBG

LM324ADTBG - 4-Channel 3-32V Op Amp | onsemi | TSSOP-14

The onsemi LM324ADTBG is a four-channel general-purpose operational amplifier designed for single-supply operation from 3 V to 32 V and packaged in a 14-pin TSSOP. Each amplifier provides true differential inputs, internal frequency compensation, and an approximately 1 MHz gain-bandwidth product, making the device suitable for low-cost signal conditioning, buffering, and analog control applications. An operational amplifier is an analog integrated circuit that uses high-gain differential amplification to increase the voltage difference between its two inputs. The quad operational-amplifier category groups four amplifiers in one package, reducing board area compared with four discrete single amplifiers. Within the broader hierarchy, the LM324 belongs to the amplifier IC and signal-chain categories, with applications spanning instrumentation, industrial control, sensor interfaces, and power-management circuits. Key characteristics include a 3 V to 32 V supply range, approximately 0.6 V/µs slew rate, 3 mV typical input-offset voltage, and 2 nA typical input-offset current. The device can operate with a single positive supply or split supplies, while its common-mode input range includes ground. These characteristics make it useful for battery-powered equipment and other low-voltage systems where the input signal may approach the lower supply rail. The four internal amplifiers use true differential input stages and are internally frequency compensated for unity-gain operation. The approximate 1 MHz gain-bandwidth product favors moderate-speed applications rather than precision signal paths demanding megahertz bandwidth or microvolt-level offset. Typical offset-current behavior supports high-impedance sensing, but source impedance must still be balanced to minimize offset and bias-current errors. Typical uses include current-to-voltage conversion in sensor interfaces, audio preamplification, comparator-style thresholding, active filtering, relay driving, and low-side current monitoring. The four amplifiers can also implement independent sensor channels, instrument loops, or gain stages where package size and cost matter more than precision or slew rate. When laying out the circuit, place input resistors close to the noninverting and inverting pins to reduce parasitic pickup, especially with high source impedance. Decoupling capacitors should be connected from each supply pin to ground with a short return path. Keep sensitive input traces away from switching nodes and provide adequate output-current headroom for capacitive loads because the LM324 is not rail-to-rail. This product guide combines package information, functional application guidance, selection criteria, and pin-compatible alternatives to simplify footprint planning and sourcing. For exact lead assignments, electrical limits, and ordering details, use the manufacturer datasheet and the technical information linked on this page.

RFQ Contact
LM324ADTBR2 - Quad 3-26V Op Amp, 14-TSSOP | onsemi
LM324ADTBR2

LM324ADTBR2 - Quad 3-26V Op Amp, 14-TSSOP | onsemi

The onsemi LM324ADTBR2 is a low-cost quad operational amplifier with four true differential-input amplifiers in a 14-pin TSSOP package. The device operates from 3 V to 26 V, supports supply voltages up to 32 V, and has a listed input offset voltage of 3 mV. Its four-amplifier configuration allows one package to implement four independent analog signal-conditioning channels. An operational amplifier is a high-gain analog amplifier intended for closed-loop signal conditioning. The LM324 belongs to the broader operational amplifier, analog amplifier, and integrated-circuit hierarchy. Its differential inputs compare two voltages and drive an output according to the feedback network. True differential inputs are particularly useful in single-supply circuits, where an input signal can be referenced near ground without requiring a split bipolar power supply. The principal characteristics include four amplifiers per package, a 3 V to 26 V operating range, 3 mV input offset voltage, and approximately 0.6 V/us slew rate. The 14-TSSOP package provides a compact surface-mount format for general-purpose analog designs. The manufacturer identifies the LM324 series as a low-cost family with true differential inputs and several advantages over standard operational-amplifier types in single-supply applications. Each amplifier can be configured for voltage amplification, buffering, summing, filtering, or differential signal conditioning when suitable external resistors and capacitors are used. Because the LM324 contains four independent channels, designers can reduce component count in multi-channel instrumentation, sensor-conditioning, and feedback-control circuits. Independent channels also provide flexibility when different stages require different gain values or operating conditions. Typical uses include low-cost sensor interfaces, analog measurement chains, audio and communication equipment, power-supply feedback, and industrial control modules. In each case, the designer must verify input common-mode range, output swing, gain-bandwidth behavior, input bias current, and stability for the selected feedback network before releasing a production design. The main design consideration is the input common-mode range. A signal-sensing circuit should keep both inputs inside the amplifier's permitted common-mode window throughout its operating range. Decoupling capacitors should be placed close to the supply pins, while resistor and capacitor values should be calculated for the intended gain and bandwidth rather than copied without verification. This page consolidates electrical characteristics, package details, application guidance, practical design considerations, and qualified drop-in comparison information for engineers evaluating the LM324ADTBR2.

RFQ Contact
LM324ADTBR2G - 3-32V Quad Op Amp | onsemi | TSSOP-14
LM324ADTBR2G

LM324ADTBR2G - 3-32V Quad Op Amp | onsemi | TSSOP-14

The onsemi LM324ADTBR2G is a general-purpose, single-supply quad operational amplifier with true differential inputs, a 3 V to 32 V supply range, 0.6 V/us slew rate, and 3 mV input-offset voltage. The four amplifiers are integrated in a 14-pin TSSOP package, providing a compact solution for low-cost signal conditioning, voltage amplification, filtering, and sensor-interface circuits. An operational amplifier, commonly called an op amp, is an analog semiconductor that uses high-gain differential amplification to improve the voltage level applied to its input signal. The LM324 belongs to the general-purpose amplifier class within the broader operational-amplifier, analog IC, and semiconductor hierarchy. Its four independent channels can process separate signals or be connected together for filtering, gain, summing, and other analog functions. The principal advantages of the LM324 family in single-supply systems include true differential inputs, operation from a supply as low as 3 V, and support for inputs that can approach ground potential. The integrated quad arrangement reduces component count and board area when a design needs several amplifiers. These characteristics make the device practical for cost-sensitive industrial control, instrumentation, audio, communications, and embedded-system analog front ends. Each channel consists of a differential input stage, intermediate gain stages, a push-pull output stage, and internal biasing. The output stage can source and sink current while driving typical external loads, and the device is intended for general-purpose closed-loop operation. Because it is not a rail-to-rail precision amplifier, input and output limitations must be considered when signals approach either supply rail. Typical applications include low-level sensor amplification, transducer conditioning, active filters, comparators with hysteresis, audio preamplification, current-to-voltage conversion, and general instrumentation. In a four-channel design, the same package can implement independent amplifier blocks or a higher-order filter. Supply bypassing remains essential because four amplifiers operating in one package can share the same rail and package-level thermal environment. For a new design, confirm input common-mode range, output swing, output-current capability, noise, offset, and stability requirements against the manufacturer datasheet before assigning gain. A 0.1 uF bypass capacitor close to the supply pins is a common starting point, while the datasheet should determine the final capacitance and compensation network for each feedback configuration. This product page combines the exact LM324ADTBR2G order information with verified manufacturer and distributor references, same-footprint alternatives, technical comparisons, and practical analog-design guidance. The comparisons also distinguish exact drop-in options from broader functional equivalents so engineers can protect PCB compatibility while reviewing speed, offset, supply, and temperature requirements.

RFQ Contact
LM324AM - 4-Channel 3-32V Low-Power Op Amp | Texas Instruments
LM324AM

LM324AM - 4-Channel 3-32V Low-Power Op Amp | Texas Instruments

The Texas Instruments LM324AM is a four-channel, general-purpose operational amplifier operating from a single supply of 3 V to 32 V in a 14-pin SOIC package. Each amplifier provides approximately 65 dB CMRR, operates with an output current up to 40 mA, and is intended for low-power signal-conditioning applications. The LM324AM combines four independently usable amplifier sections in one surface-mount package, reducing board area compared with four separate single or dual amplifier packages. An operational amplifier is an analog signal-processing IC that amplifies the voltage difference between its inverting and non-inverting inputs. The LM324 belongs to the general-purpose operational-amplifier hierarchy: operational amplifier → voltage-feedback amplifier → integrated amplifier IC. Its four internal sections support common tasks including voltage buffering, transducer amplification, cross-coupled differential stages, analog filtering, and sensor-signal conditioning while operating from a single positive supply. The principal advantages of the LM324AM are its low-power four-channel integration, 3 V to 32 V single-supply range, approximately 65 dB CMRR, and low-power characterization emphasized by distributors. The 14-pin SOIC format supports conventional surface-mount assembly, while the four amplifier channels can provide independent gain or buffering functions within one package. The listed operating-temperature range is 0 °C to 70 °C, matching a general-purpose commercial-temperature class rather than an explicitly automotive-qualified product. The internally frequency-compensated architecture makes the LM324AM suitable for straightforward closed-loop amplifier configurations without external compensation networks. Designers should still verify input common-mode range, output swing, output-current capability, noise, slew rate, offset voltage, and channel behavior against the manufacturer datasheet for the exact production source and grade. Because LM324-family devices are also offered by multiple manufacturers, procurement should confirm the manufacturer marking, temperature grade, qualification status, and traceability. Typical uses include industrial 4-20 mA current-loop receivers, low-voltage sensor amplifiers, audio preamplifier stages, active filters, and general analog control boards. The integrated quad format is particularly useful when four similar amplifier channels are required. For a single- or dual-channel design, however, a one- or dual-amplifier package can reduce unused channels, power consumption, and PCB area. The principal design consideration is ensuring that the input and output operating points remain within the device's allowable common-mode and output-swing limits. Layout should keep feedback-loop connections short, provide local bypassing at the supply pins, and avoid placing high-current return paths beneath sensitive analog inputs. Stable operation near ground-level signals should be checked carefully when the source impedance is high or when the required output amplitude approaches the supply rails. This page consolidates verified distributor and manufacturer information, package-level replacement guidance, practical layout notes, and parameter-by-parameter comparisons. It also distinguishes verified facts from specifications that require confirmation from the exact manufacturer datasheet, helping engineers select and qualify the LM324AM without relying on generic family assumptions.

RFQ Contact
LM324AM/NOPB - 4-Channel 1 MHz Op Amp | Texas Instruments
LM324AM/NOPB

LM324AM/NOPB - 4-Channel 1 MHz Op Amp | Texas Instruments

The Texas Instruments LM324AM/NOPB is a four-channel, general-purpose operational amplifier with a 1 MHz gain-bandwidth product, 0.5 V/us slew rate, and 3 V to 32 V single-supply operation in a 14-pin SOIC package. The LM324AM/NOPB contains four independent, high-gain, internally frequency-compensated amplifiers, allowing one device to implement multiple analog signal-conditioning channels while reducing package count and board area. An operational amplifier is an analog amplifier used to amplify voltage differences and serve as a building block in analog and mixed-signal systems. The LM324 family belongs to the operational-amplifier, analog-amplifier, and semiconductor hierarchies. Its four channels can perform buffering, voltage amplification, summing, comparison, filtering, and transducer-signal conditioning when configured with passive networks or companion components. The principal operating characteristics include four amplifier circuits, a 1 MHz gain-bandwidth product, 0.5 V/us slew rate, and a 3 V to 32 V total supply range. The low-power bipolar architecture supports single-supply operation, while internal frequency compensation allows practical closed-loop gain stages without external compensation components. The 14-pin SOIC form factor is also compatible with standard surface-mount assembly and tube-packaging workflows. Internal frequency compensation trades higher bandwidth for simple implementation and stable operation in general-purpose analog circuits. Each amplifier can use its supply rails as input common-mode limits, so input and output signals must remain within the permitted operating range. Circuit designers should account for input offset voltage, input bias current, output-current capability, common-mode limits, and output swing when choosing gain, feedback values, and external loading. Typical uses include four-channel sensor conditioning, low-frequency active filters, audio preamplifier stages, general signal buffers, DC summing networks, and mixed-signal interface circuits. The 1 MHz bandwidth is most appropriate for low-frequency and moderate-bandwidth tasks rather than high-speed instrumentation, where a wider-bandwidth amplifier would normally be preferred. The four-channel configuration is especially useful when a board needs several matched general-purpose amplifier functions. Keep input and output return paths short, decouple each supply rail close to the device, and place feedback components close to the relevant amplifier pins. Avoid driving capacitive loads directly unless the configured gain, load value, and stability behavior have been checked. Input bias-current compensation is important for high-impedance sources because the LM324 uses bipolar input transistors rather than CMOS inputs. This product record combines the exact LM324AM/NOPB package, operating, and amplifier data with practical application guidance, drop-in comparison options, and design considerations for efficient single-supply analog design.

RFQ Contact
LM324AMX/NOPB - 32V Quad 1MHz Op Amp | Texas Instruments
LM324AMX/NOPB

LM324AMX/NOPB - 32V Quad 1MHz Op Amp | Texas Instruments

The Texas Instruments LM324AMX/NOPB is a low-power, general-purpose quad operational amplifier containing four independent, high-gain, internally frequency-compensated amplifiers. The device operates from a single power supply across a 3 V to 32 V range and provides approximately 1 MHz gain-bandwidth performance. It is packaged in a 14-pin SOIC (D) rated for a 0°C to 70°C ambient temperature range. An operational amplifier is an analog signal-conditioning IC that amplifies the difference between its inverting and non-inverting inputs. The operational-amplifier category includes general-purpose amplifiers, precision amplifiers, instrumentation amplifiers, and comparators; the LM324 belongs to the general-purpose single-supply amplifier family. Its four independent channels can run from the same supply while handling separate signal paths. The LM324AMX/NOPB provides a large DC voltage gain of 100 dB and is internally compensated for stable operation at unity gain. Its wide 3 V to 32 V supply range supports both conventional 5 V and 12 V analog systems as well as higher-voltage industrial rails. The output can swing from approximately 0 V to VCC minus 1.5 V, making rail-to-rail operation unnecessary when the signal remains within that range. The input common-mode voltage range includes ground, which is useful for single-supply sensing circuits. The amplifier's low-power architecture suits battery-operated instrumentation, analog signal conditioning, sensor amplification, and control loops where a precision rail-to-rail amplifier is unnecessary. Four amplifiers in one package also reduce board area when a design needs several similar analog channels. The internally compensated topology simplifies stable feedback design around unity gain, although applications requiring higher closed-loop gain or faster settling need additional bandwidth and stability analysis. Typical uses include transducers with ground-referenced outputs, current sensing, buffering, level shifting within the common-mode range, and general-purpose analog filtering. Each channel provides input and output pins in the same 14-pin SOIC outline, so no external isolation or separate bias circuitry is required for the basic amplifier function. Design should preserve the input common-mode and output-swing limits, especially near the positive supply rail. Where the signal can approach the upper rail, add headroom or select an amplifier with rail-to-rail output capability. Decoupling capacitors should be placed close to the supply pins, and unused amplifier channels should be configured conservatively rather than left floating. This page combines manufacturer specifications with package details, application guidance, drop-in replacement analysis, and practical design notes to support faster component selection and PCB planning.

RFQ Contact
LM324AN - Quad 30V 1.2MHz Op Amp | Texas Instruments
LM324AN

LM324AN - Quad 30V 1.2MHz Op Amp | Texas Instruments

The Texas Instruments LM324AN is a low-power, quad operational amplifier containing four independent, high-gain, internally frequency-compensated amplifiers in a 14-pin PDIP package. The device operates from a single power supply, supports a maximum supply voltage of 30 V, and is specified for a gain-bandwidth product of 1.2 MHz with an input offset voltage rating of 3 mV. Its operating temperature range is 0°C to 70°C. An operational amplifier is an analog integrated circuit that amplifies the difference between its non-inverting and inverting inputs. The LM324AN belongs to the general-purpose operational amplifier family within the broader voltage-amplifier and analog signal-conditioning hierarchy. Internally compensated gain stages allow the amplifier to provide stable closed-loop operation without an external compensation capacitor, while the differential input architecture supports common-mode operation from ground upward in many single-supply circuits. Each of the four amplifier sections has a differential input, an output, and internal bias compensation. The 3 mV input offset rating is suitable for general instrumentation, sensor interfaces, active filtering, and audio preamplification where the signal is not operating near the precision limits of a dedicated low-offset amplifier. The 1.2 MHz gain-bandwidth product provides adequate bandwidth for low-frequency control, buffering, and modest-frequency signal-processing applications. The LM324AN is a classic single-supply-oriented device, but its wide supply capability also permits conventional dual-supply operation where the common-mode input range permits it. The four independent amplifiers can implement separate gain stages, comparators, filters, or buffer functions in one package. The through-hole PDIP construction is particularly useful for prototype boards, educational systems, industrial controllers, and repair assemblies where socketed or manually inserted parts are preferred over fine-pitch surface-mount packages. Typical uses include DC signal conditioning, bridge-amplifier interfaces, loop filtering, audio mixing stages, general feedback control, and low-cost sensor amplification. Because the LM324AN is not a rail-to-rail input or output amplifier, the engineer should verify input common-mode range and output swing against the selected supply voltage. Decoupling capacitors are normally placed close to the supply pins to control impedance and prevent feedback from disturbing analog signal integrity. For new precision designs, compare the LM324AN with rail-to-rail or low-offset alternatives before committing to the design. For established DIP-14 layouts and repair work, the LM324AN remains useful because several LM324-family devices from different manufacturers are offered in the same 14-pin through-hole footprint. Pricing shown for this page is referenced as of October 29, 2026 and should be rechecked against current distributor inventory. This page consolidates manufacturer specifications, verified distributor listings, cross-reference options, pin-level implementation guidance, and application-specific design notes that help engineers evaluate the LM324AN beyond a basic distributor catalogue entry.

RFQ Contact
LM324AN/NOPB - Quad 1 MHz General-Purpose Op Amp | Texas Instruments
LM324AN/NOPB

LM324AN/NOPB - Quad 1 MHz General-Purpose Op Amp | Texas Instruments

The Texas Instruments LM324AN/NOPB is a quad general-purpose operational amplifier in a 14-pin PDIP package, integrating four independent, high-gain, internally frequency-compensated amplifiers in one monolithic die. Each channel operates from a single supply as low as 3 V up to 30 V, delivering a typical open-loop gain of 100 dB, a 1.0 MHz gain-bandwidth product and a 0.5 V/us slew rate. An operational amplifier (op amp) is a high-gain differential amplifier whose inverting and non-inverting inputs are compared and amplified. When negative feedback is applied, the closed-loop gain is set entirely by external resistors, which makes the op amp the basic building block of the analog signal chain: it sits in the hierarchy above discrete transistor gain stages and below complete application circuits such as amplifiers, filters, comparators, transducers and line drivers. The LM324 family, introduced by National Semiconductor and now a Texas Instruments product, is the archetypal single-supply general-purpose quad. The LM324A device in the LM324AN/NOPB provides a typical input offset voltage of 2 mV, an input bias current of 250 nA, and a typical supply current of 0.8 mA per amplifier, so four channels consume roughly 3.2 mA at 5 V. Output swing reaches within 20 mV of the negative rail and about 100 mV below the positive rail at 100 kΩ load, while the output can source or sink tens of milliamperes. Internal differential input and output protection diodes tolerate rail-to-rail input transients. The architecture is a classic bipolar, voltage-feedback design with a single dominant-pole compensation network per channel, giving unity-gain stability without external compensation. Noise is dominated by input-referred voltage noise of roughly 45 nV/√Hz at 1 kHz, and the amplifiers are designed for unity-gain operation in comparators, buffers and general analog signal conditioning. Typical applications include low-cost sensor signal conditioning, 4-20 mA current-loop receivers, audio mixer subcircuits, active filters, temperature controllers, bridge amplifier front ends, power-supply feedback loops and general instrumentation. Because the package is a through-hole PDIP-14, the part also fits legacy industrial and educational control boards that were designed around the original LM324 footprint. A key design consideration is that the LM324 does not rail-to-rail output and its common-mode input range excludes the positive rail, so headroom must be planned for single-supply designs. The input bias current flows through the source resistance, so matched resistor networks keep output offset small. Using the device as a comparator requires care because output saturation recovery takes several microseconds. This page adds information the datasheet does not provide: a drop-in alternative matrix with quantified differences, package and pinout reference, engineering design notes covering decoupling and input common-mode limits, and a parameter-by-parameter comparison table for selecting between the Texas Instruments, onsemi and equivalent quad op amp sources.

RFQ Contact
LM324AN/PB - Quad 30V 1.2MHz Op Amp | Texas Instruments (Lead-Free (Pb-Free))
LM324AN/PB

LM324AN/PB - Quad 30V 1.2MHz Op Amp | Texas Instruments (Lead-Free (Pb-Free))

The Texas Instruments LM324AN/PB is a low-power, quad operational amplifier containing four independent, high-gain, internally frequency-compensated amplifiers in a 14-pin PDIP package. The device operates from a single power supply, supports a maximum supply voltage of 30 V, and is specified for a gain-bandwidth product of 1.2 MHz with an input offset voltage rating of 3 mV. Its operating temperature range is 0°C to 70°C. An operational amplifier is an analog integrated circuit that amplifies the difference between its non-inverting and inverting inputs. The LM324AN/PB belongs to the general-purpose operational amplifier family within the broader voltage-amplifier and analog signal-conditioning hierarchy. Internally compensated gain stages allow the amplifier to provide stable closed-loop operation without an external compensation capacitor, while the differential input architecture supports common-mode operation from ground upward in many single-supply circuits. Each of the four amplifier sections has a differential input, an output, and internal bias compensation. The 3 mV input offset rating is suitable for general instrumentation, sensor interfaces, active filtering, and audio preamplification where the signal is not operating near the precision limits of a dedicated low-offset amplifier. The 1.2 MHz gain-bandwidth product provides adequate bandwidth for low-frequency control, buffering, and modest-frequency signal-processing applications. The LM324AN/PB is a classic single-supply-oriented device, but its wide supply capability also permits conventional dual-supply operation where the common-mode input range permits it. The four independent amplifiers can implement separate gain stages, comparators, filters, or buffer functions in one package. The through-hole PDIP construction is particularly useful for prototype boards, educational systems, industrial controllers, and repair assemblies where socketed or manually inserted parts are preferred over fine-pitch surface-mount packages. Typical uses include DC signal conditioning, bridge-amplifier interfaces, loop filtering, audio mixing stages, general feedback control, and low-cost sensor amplification. Because the LM324AN/PB is not a rail-to-rail input or output amplifier, the engineer should verify input common-mode range and output swing against the selected supply voltage. Decoupling capacitors are normally placed close to the supply pins to control impedance and prevent feedback from disturbing analog signal integrity. For new precision designs, compare the LM324AN/PB with rail-to-rail or low-offset alternatives before committing to the design. For established DIP-14 layouts and repair work, the LM324AN/PB remains useful because several LM324-family devices from different manufacturers are offered in the same 14-pin through-hole footprint. Pricing shown for this page is referenced as of October 29, 2026 and should be rechecked against current distributor inventory. This page consolidates manufacturer specifications, verified distributor listings, cross-reference options, pin-level implementation guidance, and application-specific design notes that help engineers evaluate the LM324AN/PB beyond a basic distributor catalogue entry.

RFQ Contact
LM324ANE4 - Quad 14-PDIP Op Amp | Texas Instruments
LM324ANE4

LM324ANE4 - Quad 14-PDIP Op Amp | Texas Instruments

Texas Instruments LM324ANE4 is a low-power, quadruple operational amplifier designed for general-purpose analog signal conditioning from single or split power supplies. The device contains four amplifiers in one 14-PDIP package and is associated with a wide supply-voltage operating range. According to the Texas Instruments LM324 product page, the LM324 family is optimized for low-power operation, while the device description identifies it as a low-power quad operational amplifier for single-supply applications. An operational amplifier is an analog integrated circuit that uses high-gain differential amplification to compare and process voltages. The LM324 family belongs to the operational-amplifier hierarchy within analog and signal-chain ICs. Four amplifiers in one package can support buffer, amplifier, comparator, summing, difference, filtering, and level-conversion functions while reducing board area and external component count. The LM324ANE4 combines four amplifier channels with single-supply operation. The component documentation describes operation from split supplies with a total supply difference from 3 V to 32 V, and notes a typical low supply-current drain of 0.8 mA. Its input common-mode voltage range includes ground, allowing the amplifier to process input signals near the lower supply rail. This rail-to-near-ground input capability is particularly useful in systems powered from a single positive supply. Each internal amplifier includes the input and output functions needed for conventional closed-loop analog designs. Feedback components establish gain and filtering behavior, while the open-loop characteristics of the internal transistor stages determine signal amplification, common-mode behavior, and output-drive capability. Because all four channels share one package and supply pins, the device is especially practical when a board needs several similar signal-conditioning channels rather than unrelated mixed functions. Typical applications include low-frequency audio and control circuits, DC signal amplifiers, active filters, sensor-signal conditioning, and general industrial interface boards. The four-channel organization can simplify a design requiring multiple gain stages or parallel low-bandwidth analog channels. The 14-PDIP package also supports through-hole assembly and prototype-board layouts where a surface-mount package would be inconvenient. Designers should verify the exact input common-mode limits, output-swing limits, supply-current behavior, electrical characteristics, and operating-temperature grade in the manufacturer datasheet before finalizing signal headroom. Input and output stability also depends on the selected feedback network, source impedance, load, decoupling, and board layout. Place bypass capacitors close to the supply pins and keep sensitive input nodes away from high-current return paths. This product page combines manufacturer-product information, datasheet references, package and pinout details, application guidance, and same-footprint alternative analysis. It is designed to help engineers evaluate the LM324ANE4 alongside other Texas Instruments LM324 ordering codes while preserving the constraints of a 14-PDIP, four-channel general-purpose amplifier.

RFQ Contact
LM324ANG - 4-Channel 3-32V Op Amp | onsemi | Through-Hole
LM324ANG

LM324ANG - 4-Channel 3-32V Op Amp | onsemi | Through-Hole

The onsemi LM324ANG is a low-cost, four-channel operational amplifier designed for general-purpose single-supply applications, with four true differential-input amplifiers in a 14-pin through-hole PDIP package. The device operates from 3 V to 32 V, supports a 1 MHz gain-bandwidth product, and has a specified input offset voltage of 3 mV. Its four-amplifier configuration reduces package count and provides a practical approach to multi-channel signal conditioning without requiring four separate single op-amp packages. An operational amplifier is an analog integrated circuit that amplifies the difference between two input voltages. The LM324 series belongs to the quad operational-amplifier family within the broader linear amplifier and signal-conditioning hierarchy. Its differential input architecture is useful for comparing a sensor signal with a reference voltage, amplifying small signals in control systems, buffering high-impedance sources, and implementing basic active filters or summing circuits. The LM324ANG combines four amplifiers, single-supply operation from 3 V to 32 V, a 1 MHz gain-bandwidth product, and a 65 dB minimum common-mode rejection ratio. These characteristics make it suitable for industrial control, instrumentation, sensor interfaces, audio and communications support circuits, and general embedded-system analog conditioning. The input offset voltage of 3 mV is important in precision-sensitive applications and should be considered when defining acceptable error budgets. The device is intended for general-purpose, non-quadrature applications where economical integration and simple single-supply operation are more important than low-noise, high-speed, or rail-to-rail performance. Its four internal channels share the device power rails but provide independent differential inputs and outputs. Engineers should design feedback networks around the required closed-loop gain and check output swing, input common-mode range, output-current capability, and stability at the selected operating voltage. Typical circuit roles include amplifying a 0-5 V sensor signal, buffering a potentiometer, comparing a control signal with a reference, driving the input stage of a power circuit, and providing four independent amplifier channels in one package. The 14-pin PDIP package is suited to through-hole PCB assembly, educational prototypes, industrial control boards, and repair or modernization work where a pin-compatible replacement is needed. When laying out a board, place input, feedback, and decoupling connections close to the device, connect the power pins to a low-impedance ground plane, and decouple the supply near the package. Avoid long high-impedance input traces because leakage and board contamination can increase offset error. Review the manufacturer datasheet for the exact pin assignment, input common-mode limits, output swing, supply-current behavior, and recommended compensation values. This page combines the LM324ANG’s core electrical and package characteristics with application guidance, design notes, and practical drop-in alternatives. It is intended to help engineers select the part quickly, compare equivalent quad op amps, and plan a PCB or replacement strategy without overlooking the limitations of a general-purpose operational amplifier.

RFQ Contact
LM324ANS - Quad 14-SO General-Purpose Op Amp | Texas Instruments
LM324ANS

LM324ANS - Quad 14-SO General-Purpose Op Amp | Texas Instruments

The Texas Instruments LM324ANS is a quad general-purpose operational amplifier packaged in a 14-pin SOIC (14-SO) package. It contains four independent, internally frequency-compensated amplifier sections designed for low-cost signal conditioning, voltage amplification, filtering, comparison, and general analog control applications. The device supports single-supply or dual-supply operation across a wide voltage range, making it suitable for industrial, consumer, instrumentation, and educational equipment. An operational amplifier, or op amp, is a high-gain differential-input amplifier whose feedback network determines the closed-loop behavior. The LM324 belongs to the linear-amplifier hierarchy within the broader voltage-feedback amplifier and analog-signal-conditioning categories. Its four independent sections allow one package to implement several stages in a circuit without requiring four separate amplifier packages. Key features of the LM324ANS include four amplifier sections in one 14-SO package, internal frequency compensation, operation from a single power supply, operation with a positive ground-referenced common-mode input range, and low supply-current consumption. The internal compensation simplifies design because most closed-loop gain configurations do not require an external frequency-compensation capacitor. The wide common-mode and supply ranges are useful when sensing signals near ground or operating from a single battery-derived rail. Each amplifier section has differential inputs and an output, while the package provides a common supply connection. Because the LM324 is intended for general-purpose analog work, it is more appropriate for moderate-bandwidth signal conditioning than for high-speed precision applications. The device can buffer sensor outputs, amplify small voltage changes, implement active filters, and provide simple threshold-based control functions. Its internally compensated architecture favors straightforward, stable implementation over the flexibility of a high-performance precision amplifier. Typical applications include industrial sensor interfaces, audio preamplifier stages, low-frequency active filters, control-loop amplifiers, data acquisition front ends, and educational analog systems. In a sensor interface, the quad configuration can amplify the transducer output, buffer the reference, provide gain, and drive a following filtering stage. In audio equipment, separate sections can handle input amplification, tone-control filtering, and output buffering. The 14-SO package also simplifies assembly in designs that require a quad amplifier but not a high-pin-count or high-speed package. When laying out the circuit, place input and output decoupling capacitors close to the supply pins and keep sensitive input traces away from output and switching nodes. Check input and output common-mode limits for the selected supply voltage, especially when signals approach the positive rail. Use the manufacturer pinout and application guidance for the final PCB implementation.

RFQ Contact
LM324ANSR - Quad 14-SO General-Purpose Op Amp | Texas Instruments (Tape & Reel)
LM324ANSR

LM324ANSR - Quad 14-SO General-Purpose Op Amp | Texas Instruments (Tape & Reel)

The Texas Instruments LM324ANSR is a quad general-purpose operational amplifier packaged in a 14-pin SOIC (14-SO) package. It contains four independent, internally frequency-compensated amplifier sections designed for low-cost signal conditioning, voltage amplification, filtering, comparison, and general analog control applications. The device supports single-supply or dual-supply operation across a wide voltage range, making it suitable for industrial, consumer, instrumentation, and educational equipment. An operational amplifier, or op amp, is a high-gain differential-input amplifier whose feedback network determines the closed-loop behavior. The LM324 belongs to the linear-amplifier hierarchy within the broader voltage-feedback amplifier and analog-signal-conditioning categories. Its four independent sections allow one package to implement several stages in a circuit without requiring four separate amplifier packages. Key features of the LM324ANSR include four amplifier sections in one 14-SO package, internal frequency compensation, operation from a single power supply, operation with a positive ground-referenced common-mode input range, and low supply-current consumption. The internal compensation simplifies design because most closed-loop gain configurations do not require an external frequency-compensation capacitor. The wide common-mode and supply ranges are useful when sensing signals near ground or operating from a single battery-derived rail. Each amplifier section has differential inputs and an output, while the package provides a common supply connection. Because the LM324 is intended for general-purpose analog work, it is more appropriate for moderate-bandwidth signal conditioning than for high-speed precision applications. The device can buffer sensor outputs, amplify small voltage changes, implement active filters, and provide simple threshold-based control functions. Its internally compensated architecture favors straightforward, stable implementation over the flexibility of a high-performance precision amplifier. Typical applications include industrial sensor interfaces, audio preamplifier stages, low-frequency active filters, control-loop amplifiers, data acquisition front ends, and educational analog systems. In a sensor interface, the quad configuration can amplify the transducer output, buffer the reference, provide gain, and drive a following filtering stage. In audio equipment, separate sections can handle input amplification, tone-control filtering, and output buffering. The 14-SO package also simplifies assembly in designs that require a quad amplifier but not a high-pin-count or high-speed package. When laying out the circuit, place input and output decoupling capacitors close to the supply pins and keep sensitive input traces away from output and switching nodes. Check input and output common-mode limits for the selected supply voltage, especially when signals approach the positive rail. Use the manufacturer pinout and application guidance for the final PCB implementation.

RFQ Contact
LM324ANSRG4 - 1.2MHz Quad Op Amp | Texas Instruments
LM324ANSRG4

LM324ANSRG4 - 1.2MHz Quad Op Amp | Texas Instruments

Texas Instruments LM324ANSRG4 is a four-circuit general-purpose operational amplifier packaged in a 14-pin SOIC. The device combines a nominal gain-bandwidth product of 1.2 MHz with low supply-current drain of 0.8 mA typical, while its common-mode input range includes ground for convenient single-supply operation. The LM324 family integrates four amplifiers in one package, reducing board area compared with four individual single-amplifier packages. An operational amplifier is a voltage-gain element that uses differential input voltage to control an output. A quad operational amplifier contains four similar amplifier sections and belongs to the broader hierarchy of analog amplifiers, amplifier ICs, and integrated circuits. The LM324ANSRG4 is intended for general-purpose signal conditioning, where low cost, supply versatility, and straightforward operation are more important than high speed or low offset. Four amplifier circuits are provided in one 14-SOIC package, reducing component count and simplifying PCB assembly. The 1.2 MHz gain-bandwidth product supports applications operating at relatively low frequencies, including buffered sensor signals, slow analog control loops, audio paths, and general signal conditioning. A typical supply-current drain of 0.8 mA is useful for battery-powered or low-power equipment, although total system consumption also depends on the operating voltage and load on each amplifier. The common-mode input voltage range includes ground, allowing a single positive supply to process signals that approach 0 V. This characteristic simplifies sensor interfaces whose outputs remain near the lower supply rail. The device is identified as a standard general-purpose amplifier and is assembled in a surface-mount 14-SOIC package, which supports automated manufacturing and compact PCB layouts. Typical uses include four-channel sensor conditioning, low-frequency active filters, buffered analog inputs, general-purpose instrumentation, and educational or experimental amplifier circuits. Because the LM324ANSRG4 provides four matched functional sections, designers can allocate amplifiers to input buffering, gain stages, active filtering, and output conditioning within one package. A key design consideration is to keep each signal within the amplifier's common-mode and output-voltage limits throughout its operating range. Decoupling capacitors should be placed close to the power pins, and unused amplifier sections should be configured according to the manufacturer's recommendations rather than left floating. Stable feedback networks and suitable source and load impedances remain important for predictable closed-loop behavior. This product page combines package, electrical, application, sourcing, and replacement guidance in one engineering-oriented reference. It also distinguishes true same-footprint alternatives from broader LM324-family devices that use different packages, helping PCB designers avoid substitutions that require layout changes.

RFQ Contact
LM324APWR - Quad 30V 1.2MHz Op Amp | Texas Instruments
LM324APWR

LM324APWR - Quad 30V 1.2MHz Op Amp | Texas Instruments

The Texas Instruments LM324APWR is a four-circuit general-purpose operational amplifier designed for single- or dual-supply operation. It provides a maximum supply rating of 30 V, a gain-bandwidth product of 1.2 MHz, input offset voltage of 3 mV, and four amplifiers in a 14-pin TSSOP package. The LM324APWR is intended for cost-sensitive analog signal conditioning, instrumentation, and control applications. An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its non-inverting and inverting inputs. The LM324 belongs to the voltage-feedback operational-amplifier hierarchy, within analog ICs and broader semiconductor electronics. Its four amplifiers can perform independent functions or be configured for differential, summing, filtering, comparison, and feedback-amplifier circuits. This quad organization reduces component count and simplifies PCB layout in multi-channel analog systems. The LM324A family is optimized for general-purpose requirements rather than high-speed or precision applications. Key characteristics include four amplifier circuits, a 30 V maximum supply, 1.2 MHz gain-bandwidth product, and 3 mV input offset voltage. The LM324APWR temperature grade is specified from 0°C to 70°C, making it suitable for commercial equipment operating within that ambient range. The 14-TSSOP package also supports compact, surface-mounted PCB construction. The LM324 architecture uses four amplifiers operating from a common positive and negative supply. Its 1.2 MHz gain-bandwidth product is adequate for audio-frequency, sensor-interface, and low-to-moderate-bandwidth feedback loops. The 3 mV input offset specification is the primary limitation for high-precision bridge or current-sense measurements, where offset error can create a meaningful output error after amplification. Designers should calculate the closed-loop gain, output swing, input common-mode range, and required output-current margin for the intended circuit. Typical applications include four-channel sensor conditioning, industrial control signal interfaces, audio preamplifier stages, low-frequency active filters, and general instrumentation. Multiple LM324 channels can monitor several analog inputs in a controller or provide basic current-to-voltage conversion around resistive sensors. The device is also useful when one circuit needs buffering while other channels perform summing or active-filter functions. For a new design, verify the 0°C to 70°C temperature range, 30 V maximum supply, and 1.2 MHz bandwidth against the operating requirements. Place decoupling capacitors close to the supply pins, route each amplifier's feedback components close to the corresponding channel, and maintain compatible signal levels around the amplifier inputs. The LM324APWR is most appropriate when low cost, four integrated channels, and broad supply-voltage flexibility outweigh the lower bandwidth and higher offset of precision op amps. This product page combines manufacturer specifications, package and pin information, application guidance, and constrained drop-in alternatives. It also distinguishes temperature-grade and B-family options by their documented supply range, offset voltage, and operating-temperature differences, helping engineers make a PCB-compatible sourcing decision without confusing electrical equivalence with functional similarity.

RFQ Contact
LM324APWRG4 - Quad General-Purpose Op Amp, 14-TSSOP | Texas Instruments
LM324APWRG4

LM324APWRG4 - Quad General-Purpose Op Amp, 14-TSSOP | Texas Instruments

The Texas Instruments LM324APWRG4 is a quadruple general-purpose operational amplifier in a 14-pin TSSOP package, containing four independent, internally frequency-compensated amplifiers designed to run from a single supply or split supply over a wide voltage range up to ±16 V (32 V total). Each channel offers a typical input offset voltage of ±3 mV, a supply-current drain of 0.8 mA typ per amplifier that stays essentially independent of supply voltage, and 2 kV ESD protection. An operational amplifier is a high-gain, differential-input, single-ended-output active device that drives its output toward the higher of its two inputs. The LM324 belongs to the quad general-purpose op-amp family, a direct descendant of the classic single LM741 architecture in which four amplifiers share one package. In the signal-chain hierarchy it sits between discrete transistor stages and precision instrumentation amplifiers: it is a voltage-feedback, internally compensated (unity-gain stable) amplifier aimed at cost-sensitive, high-volume analog signal conditioning. Key differentiators of the LM324A grade are the tighter ±3 mV typical input offset voltage and the enhanced ESD robustness compared with earlier LM324 revisions. Because each amplifier is internally compensated, it behaves correctly at unity gain without external frequency-compensation networks, and the common-mode input range includes ground so the device can be used in single-supply sensing circuits whose signal swings to 0 V. The A suffix denotes the improved-offset version, while the PWRG4 suffix denotes the 14-pin TSSOP, tape-and-reel, RoHS-green (lead-free) ordering code. Because the package is only 14 pins across and 0.8 mm pitch, four amplifiers fit into a footprint comparable to a single SOIC-14, which keeps quad-buffer, quad-instrumentation and multi-channel sensor-conditioning boards compact. Typical applications include sensor signal conditioning, low-side current monitoring, DC motor and actuator driver stages, audio mixer sub-circuits, temperature-controller error amplifiers, and general instrumentation buffers. Four matched channels in one package also reduce board area, ground-bounce risk, and part-count on multi-channel analog boards. When designing with the LM324APWRG4, remember that it is not a rail-to-rail input or output amplifier: the common-mode and output swing limits are set by the supply rails, so headroom of a few hundred millivolts must be reserved at the output. Decouple each supply pin locally, keep feedback loops short, and prefer the LM324A offset grade over the base LM324 when accuracy matters.

RFQ Contact
LM324AWDT - Low-Power Quad Op Amp | STMicroelectronics
LM324AWDT

LM324AWDT - Low-Power Quad Op Amp | STMicroelectronics

STMicroelectronics LM324AWDT is a low-power, general-purpose quad operational amplifier containing four independent, internally frequency-compensated amplifiers in a 14-pin SO package. The device operates from a single supply or from split dual supplies, with a verified operating capability extending to ±15 V, equivalent to 30 V total supply span. Its four-circuit integration reduces board area and component count in analog signal-conditioning designs. An operational amplifier is an analog voltage amplifier whose gain, filtering, buffering, and feedback behavior are determined mainly by external components. The LM324 belongs to the general-purpose amplifier hierarchy: op amp, analog amplifier, signal-conditioning IC, and ultimately semiconductor. A quad package contains four amplifiers that may be used independently or together for instrumentation, control, filtering, and signal conversion. The LM324 family is designed for low power consumption and low input bias current. Internally compensated operation simplifies closed-loop design because no external compensation network is required for typical voltage-feedback use. The four amplifiers are independent, allowing simultaneous sensing and actuation, although the common supply pins mean that all four channels share the same supply-voltage and ground references. The A designation identifies a distinct qualification or ordering configuration within the LM324 family, while W indicates tape-and-reel packaging and DT identifies the 14-pin small-outline package. Engineers should confirm the exact temperature limits, electrical limits, and qualification status for the selected ordering code in the STMicroelectronics datasheet before using the device in a regulated end application. Typical uses include low-frequency sensor conditioning, feedback control loops, active filters, audio and communication signal paths, and general analog instrumentation. In a 5 V single-supply system, the common reference arrangement and input/output swing limits remain central design constraints. In split-supply circuits, the device is particularly useful when the signal can swing around 0 V. Keep input and output voltages within the absolute maximum ratings, observe the input common-mode range, and provide stable bypass capacitance near the supply pins. Because the LM324 is intended mainly for general-purpose and low-frequency work, designs requiring wide input swing, very low offset, high speed, rail-to-rail output, or low-noise performance should compare the exact datasheet limits against precision or modern amplifier families. This page combines the LM324AWDT family identity, package information, qualification distinctions, drop-in ordering options, application guidance, and practical design considerations in a format designed to help engineers evaluate replacements without overlooking the electrical differences between ordering codes.

RFQ Contact
LM324AWPT - Quad Low-Power Op Amp, 1.3MHz, TSSOP-14 | STMicroelectronics
LM324AWPT

LM324AWPT - Quad Low-Power Op Amp, 1.3MHz, TSSOP-14 | STMicroelectronics

The STMicroelectronics LM324AWPT is a low-power, low-input-bias-current quad operational amplifier integrating four independent, internally frequency-compensated gain stages in a single 14-pin TSSOP (Tape and Reel) package. The 'A' suffix designates the enhanced input-offset-voltage grade, which tightens Vio to a maximum of 2 mV at 25°C versus 7 mV for the standard LM324, while the 'W' suffix extends the operating temperature range to -40°C to +105°C for industrial environments. Each of the four channels delivers a gain-bandwidth product of approximately 1.3 MHz and a slew rate of 0.4 V/µs, drawing only 1.5 mA of quiescent supply current total regardless of channel loading. A quad operational amplifier (quad op-amp) is a monolithic integrated circuit that places four independent, internally-compensated op-amp cells in one package sharing common power pins. Quad op-amps belong to the broader operational amplifier family, which in turn falls under the linear IC hierarchy and finally under analog signal-conditioning semiconductors. Compared with single or dual op-amps, quad devices reduce PCB area, simplify routing, and lower the per-channel cost in applications requiring multiple gain, buffer, filter or comparator stages. The LM324 series uses bipolar transistor input stages that can operate from a single supply as low as 3 V or from split ±1.5 V to ±16 V rails, with true ground-sensing capability on the input common-mode range. The differential input range includes the negative rail, eliminating the need for external biasing in single-supply designs. Output swing typically reaches within a few millivolts of both rails at moderate loads, and the device sustains continuous output short-circuits to ground or either rail thanks to internal current limiting. Typical applications include active filters, transducer signal conditioning, DC gain blocks, voltage followers, comparators, and general-purpose analog signal chains in consumer, industrial and automotive subsystems. The wide supply range makes the part especially popular in 5 V single-rail microcontroller-interface circuits, where four op-amps share one supply rail alongside the MCU. When designing with the LM324AWPT, place a 0.1 µF ceramic bypass capacitor within 5 mm of the VCC pin and consider the input bias current of 20 nA typical (50 nA maximum) when selecting source impedances — bias currents up to 50 nA across a 100 kΩ source produce a 5 mV offset error. Avoid using this part in precision sub-millivolt instrumentation paths; choose the LM324A-grade offset only when 2 mV is acceptable. Always consult the official STMicroelectronics datasheet for full DC and AC characteristic curves.

RFQ Contact
LM324BAIDR - Quad 36V 1.2MHz Op-Amp | Texas Instruments
LM324BAIDR

LM324BAIDR - Quad 36V 1.2MHz Op-Amp | Texas Instruments

The Texas Instruments LM324BAIDR is a quadruple operational amplifier featuring four general-purpose amplifier channels with a 36V maximum supply, 1.2MHz gain-bandwidth product, and a low input offset voltage of 2mV (B, BA versions), housed in a 14-pin SOIC (D) package rated for -40C to +85C operation. An operational amplifier (op-amp) is a high-gain voltage amplifier with differential inputs and a single-ended output, the fundamental building block of analog signal conditioning. In the analog hierarchy, the op-amp sits above discrete transistors and below specialized amplifiers such as instrumentation and audio amplifiers; general-purpose quad op-amps like the LM324 family provide four independent channels in one package for cost-sensitive multi-channel designs. The LM324BA is the next-generation BA version of the classic LM324. Key improvements over legacy LM324/LM224/LM2902 parts include a wide 3V to 36V supply range, tighter 2mV input offset voltage specification, and enhanced robustness, while remaining pin-for-pin drop-in replacements for all legacy versions. The push-pull output stage improves output voltage swing and crossover behavior compared to older Class-AB output stages, reducing the well-known LM324 output crossover distortion near the negative rail. Each of the four amplifiers shares a common supply; single-supply operation down to 3V makes the part suitable for 3.3V and 5V logic-based systems as well as traditional up to 36V industrial rails. The common-mode input range includes the negative rail, a signature LM324-family trait that simplifies single-supply designs such as sensor buffering near ground. Typical applications include industrial signal conditioning, transducer amplifier front ends, active filters, comparators and level shifters, motor-control feedback loops, and consumer appliance analog interfaces. Design consideration: the 1.2MHz gain-bandwidth limits closed-loop bandwidth; at a gain of 10, expect roughly 120kHz of usable bandwidth, so verify gain-phase margin in high-gain configurations. This page synthesizes verified distributor pricing, drop-in alternatives, pinout data, and practical design notes not found in the manufacturer datasheet alone.

RFQ Contact
LM324D - Quad 36V Op Amp | Texas Instruments | SOIC-14 (Tape & Reel)
LM324D

LM324D - Quad 36V Op Amp | Texas Instruments | SOIC-14 (Tape & Reel)

The Texas Instruments LM324D is a low-power, quadruple operational amplifier containing four independent, high-gain, internally frequency-compensated amplifiers in a 14-pin SOIC package. The verified product data identifies it as a general-purpose amplifier designed for operation from a single supply or split supply over a wide voltage range, with the B-family supply range specified as 3 V to 36 V. This quad topology lets one compact IC provide four separate analog signal-conditioning channels without requiring four discrete packages. An operational amplifier is an analog amplifier used in the wider semiconductor hierarchy of integrated circuits and analog signal-processing devices. The LM324 family is commonly used for voltage buffering, sensor-interface conditioning, current-to-voltage conversion, audio paths, filters, and control loops. Its single-supply capability is useful when the signal and system share a common ground reference, while split-supply operation supports bipolar signals in applications where positive and negative rails are available. Verified feature data identifies the LM324 family as a next-generation LM324B and LM2902B offering, with B versions intended as drop-in replacements for LM224, LM324, and LM2902 versions. The listed operating supply range is 3 V to 36 V. The family also includes versions with input offset voltage specified as low as plus or minus 2 mV, 2 kV HBM ESD protection for B, BA, and K versions, and internal RF and EMI filtering for B and BA versions. These features support general-purpose analog designs where supply tolerance and input conditioning matter. The LM324D is packaged in the SOIC-14 footprint, making it suitable for conventional PCB assembly and educational, industrial-control, instrumentation, and embedded-control designs. The device is not a precision, rail-to-rail-input amplifier, so input common-mode range, output swing, input bias current, noise, slew rate, and stability behavior must be checked against the actual signal path. The four amplifiers share a package power supply but operate independently at their input, output, and feedback pins. Typical uses include four-channel sensor buffering, low-frequency active filtering, audio preamplification, DC gain stages, comparator-style threshold conditioning with suitable feedback arrangements, and general embedded analog interfaces. When designing around the LM324D, verify the supply rails, keep input and feedback connections short, provide stable bypass capacitance near the supply pins, and account for the amplifier’s output-current and thermal limits. The manufacturer product page and datasheet are the authoritative sources for exact electrical limits and ordering information. This page combines verified manufacturer and distributor links with application guidance and explicitly marks electrical details that were not supplied in the verified excerpts. The LM324D remains a practical choice when four general-purpose amplifiers, single-supply operation, and a standard SOIC-14 footprint are more important than precision or rail-to-rail performance.

RFQ Contact
LM324DE4 - Quad 1.2MHz Op Amp, 14-SOIC | Texas Instruments
LM324DE4

LM324DE4 - Quad 1.2MHz Op Amp, 14-SOIC | Texas Instruments

Texas Instruments LM324DE4 is a general-purpose quad operational amplifier with four amplifiers, 1.2 MHz gain-bandwidth product, 0.5 V/µs slew rate, and a ±1.5 V to ±16 V supply range, packaged in a 14-pin SOIC. Each amplifier is designed for conventional analog signal-conditioning applications where low cost, wide supply-voltage operation, and four independent channels in one package are important. An operational amplifier is an amplifier IC that uses high open-loop gain and negative feedback to control gain accurately. The LM324 family combines four general-purpose amplifier channels with internal biasing, allowing each channel to operate without external bias-current compensation in typical applications. Within the semiconductor hierarchy, it belongs to the operational-amplifier, analog-amplifier, analog-IC, and integrated-circuit categories. The four internal channels can be configured as voltage followers, non-inverting or inverting amplifiers, summers, differential amplifiers, filters, comparators, and current-to-voltage converters. A 1.2 MHz gain-bandwidth product is appropriate for audio-frequency and general feedback-control circuits, while the 0.5 V/µs slew rate limits how quickly large voltage changes can be reproduced. The manufacturer datasheet identifies the device as a general-purpose amplifier with four circuits and a 14-pin SOIC package. The architecture makes efficient use of board area by placing four amplifiers in one package. Rail-to-rail output operation and the broad supply range allow the device to operate from single or dual supplies within the stated limits. Its 0.8 mA typical current drain is useful for low-power analog systems, although actual supply current depends on the number of active channels and load conditions. The package is suitable for conventional surface-mount PCB assembly. Typical LM324DE4 applications include audio preamplification, sensor signal conditioning, DC motor-control support circuits, battery-powered instrumentation, general-purpose filters, and active control loops. In multi-channel designs, the common package simplifies routing and inventory management while keeping each amplifier electrically independent. The amplifier should be selected when low bandwidth is acceptable and when a cost-conscious general-purpose implementation is more important than high-speed or low-noise performance. Design with adequate input common-mode range, output-current capability, and supply headroom. Decoupling capacitors should be placed close to the supply pins, and output loads must remain within the package and device thermal limits. Because the LM324DE4 is supplied in a tube, PCB assembly processes must support tube-fed components or require an approved conversion step before placement. This product page consolidates the exact LM324DE4 electrical and package specifications, verified same-package replacement information, a parameter comparison, application guidance, and practical PCB design notes. It is intended to accelerate component selection while preserving the distinction between exact-orderable versions and broader LM324-family devices.

RFQ Contact
LM324DG - 4-Channel 1 MHz Op Amp, 3-32 V | onsemi
LM324DG

LM324DG - 4-Channel 1 MHz Op Amp, 3-32 V | onsemi

The onsemi LM324DG is a four-channel general-purpose operational amplifier with true differential inputs, 1 MHz gain-bandwidth product, 0.6 V/us slew rate, and a 3 V to 32 V supply range, housed in a 14-pin SOIC package. The four amplifiers share one package but operate independently, making the device suitable for compact analog signal-conditioning circuits that cannot justify four separate amplifiers. An operational amplifier, or op amp, is a voltage-controlled differential amplifier whose open-loop gain is used to amplify a difference between two input signals. The LM324 belongs to the broader amplifier IC hierarchy: operational amplifier, analog amplifier, semiconductor, and integrated circuit. Its true differential inputs and ability to operate from a single positive supply are particularly useful in circuits that do not have a negative reference rail. Key features include four amplifier channels in one package, a 1 MHz gain-bandwidth product, a 0.6 V/us slew rate, input offset voltage ratings of 5 mV to 7 mV depending on the cited source, and a minimum common-mode rejection ratio of 65 dB. The 3 V to 32 V operating supply range supports both low-voltage logic systems and conventional industrial analog circuits without requiring a separate negative supply. The LM324 architecture is intended for general-purpose voltage amplification rather than precision or high-speed signal conditioning. Its relatively wide input offset voltage and modest gain-bandwidth product make it most appropriate for audio, transducer, buffering, and feedback-control stages where moderate accuracy and bandwidth are sufficient. Designers should account for input offset when measuring small signals and verify gain-bandwidth requirements for closed-loop applications. Typical uses include microphone preamplification, active audio-channel amplification, low-frequency sensor interfaces, industrial control loops, and general buffer stages. Because each channel can be assigned to a different signal or function, four independent amplifier circuits can be implemented on one board while reducing component count and simplifying routing. The primary design consideration is the absence of a negative supply in many applications. Input and output signals must remain within the device's common-mode input and output swing limits, so a negative rail is not required but can improve signal-headroom flexibility. Input and output decoupling should follow the manufacturer datasheet's recommended application circuit, and unused amplifier inputs must be biased so they remain in a defined operating state. This product page consolidates the verified LM324DG specifications, distributor references, drop-in replacement candidates, package details, and practical design guidance. It also distinguishes direct same-package substitutes from functional alternatives so engineers can narrow a replacement search without assuming that every quad op amp is electrically or mechanically interchangeable.

RFQ Contact