Products (44,000+)

LM358PE3 - Dual 700 kHz Op Amp in 8-PDIP | Texas Instruments
LM358PE3

LM358PE3 - Dual 700 kHz Op Amp in 8-PDIP | Texas Instruments

Texas Instruments LM358PE3 is a dual, general-purpose operational amplifier with a 3 V to 32 V supply range, 700 kHz gain-bandwidth product and 0.3 V/µs slew rate, housed in an 8-pin PDIP package. The device contains two independent, high-gain, internally frequency-compensated amplifiers capable of operating from a single supply or dual supplies. An operational amplifier is a high-gain differential-input semiconductor that compares two voltages and drives its output to amplify the difference between them. In the broader hierarchy, the LM358 is a dual operational amplifier, a general-purpose analog amplifier within the amplifier-IC and semiconductor categories. Its two independent channels can implement noninverting, inverting, summing, comparator, and feedback-control functions. The principal characteristics of the LM358PE3 are its 700 kHz gain-bandwidth product, 0.3 V/µs slew rate, low supply-current draw, high voltage capability and single-supply operation. The manufacturer describes the LM358 family as suitable for general-purpose signal conditioning when the circuit does not require rail-to-rail input or output swing. Its broad supply-voltage range permits use in 3 V, 5 V, 12 V and higher-rail systems when the individual channel remains within its operating limits. Each amplifier includes high gain and frequency compensation, allowing closed-loop operation without external compensation in many standard gain configurations. The 0.7 MHz bandwidth supports low-frequency signal paths more effectively than high-speed precision amplifiers, while the 0.3 V/µs slew rate limits large-signal response. Input offset voltage, input bias current, output-current capability and common-mode limits must be checked against the manufacturer datasheet for the chosen operating conditions. Typical applications include bridge and resistive sensor amplification, audio preamplification, low-frequency active filters, motor and actuator control loops, battery-powered monitoring, and general industrial signal conditioning. Two independent channels can process separate sensor signals or form the two halves of an instrumentation circuit, although common-mode and output-swing restrictions still apply. For reliable PCB implementation, preserve the manufacturer's recommended bypass capacitance, provide a low-impedance ground return, and keep feedback components close to the relevant amplifier pins. A socketed PDIP design is convenient for prototyping and repair, although a soldered package provides better mechanical reliability in production. This product page combines the LM358PE3's principal electrical characteristics with pin-level implementation guidance, application fit, drop-in alternatives and a side-by-side engineering comparison. These practical details help designers move from general amplifier selection to a reviewable circuit design.

RFQ Contact
LM358PE4 - Dual 700 kHz Op Amp, 8-PDIP | Texas Instruments
LM358PE4

LM358PE4 - Dual 700 kHz Op Amp, 8-PDIP | Texas Instruments

Texas Instruments LM358PE4 is a dual general-purpose operational amplifier with a gain-bandwidth product of 700 kHz, a slew rate of 0.3 V/µs, and a supply range extending to ±16 V per rail, housed in an 8-pin PDIP package. The device contains two independent amplifiers, making it suitable for dual-channel signal conditioning, filtering, comparisons, and basic feedback-control circuits. An operational amplifier is a voltage-feedback analog IC that uses differential input voltage to produce an amplified output voltage. Operational amplifiers belong to the amplifier hierarchy, support precise closed-loop operation when paired with external resistors, and are widely used in industrial controls, sensor interfaces, audio electronics, and power-management systems. The LM358PE4 belongs to the industry-standard LM358 family and combines two amplifiers in one package. Key electrical characteristics include a typical input offset voltage of 300 µV, a low 0.7 mA supply-current drain that is independent of supply voltage, and a common-mode input voltage range that includes ground. These features suit battery-powered, sensor-driven, and single-supply circuits where low cost, ground-referenced inputs, and two amplifiers in one package are important. The device also supports high differential input voltage capability for cost-sensitive applications. The LM358PE4 uses a bipolar voltage-feedback architecture and is specified for general-purpose analog signal processing. Its 700 kHz gain-bandwidth product makes it suitable for low-frequency audio, control, and instrumentation tasks rather than high-speed precision applications. With a 0.3 V/µs slew rate, it can produce larger output transitions more slowly than modern rail-to-rail CMOS amplifiers, so designers should check bandwidth, output swing, and stability requirements before increasing closed-loop gain. Typical applications include two-channel sensor conditioning, low-frequency active filters, audio preamplification, comparators, and industrial control interfaces. In each case, the two amplifiers can process independent signals or form a cascaded signal chain. Stable operation also requires suitable bypassing, careful grounding, and output-load consideration because the LM358PE4 is not a rail-to-rail-input or rail-to-rail-output device. For single-supply designs, bias the non-inverting input above ground and use decoupling close to the supply pins. Check the common-mode and output-voltage limits against the actual signal range, and avoid relying on output saturation as a precise comparator function. Prototype the gain, slew rate, and capacitive-load behavior before committing a high-volume design. This page combines the manufacturer specifications, package and pin information, supported alternatives, application guidance, and design notes needed to evaluate the LM358PE4. It also organizes replacement and selection questions around the verified 8-PDIP footprint, 700 kHz bandwidth, 0.3 V/µs slew rate, and 36 V maximum total supply capability.

RFQ Contact
LM358PSR - Dual Op Amp, 8-SO | Texas Instruments
LM358PSR

LM358PSR - Dual Op Amp, 8-SO | Texas Instruments

Texas Instruments LM358PSR is a standard, general-purpose dual operational amplifier packaged in an 8-SO surface-mount package. The device contains two amplifier circuits in one package, allowing designers to implement two independent analog signal-processing channels while reducing board area and component count. The LM358PSR designation identifies the Texas Instruments member of the widely used LM358 dual-operational-amplifier family. An operational amplifier is an analog integrated circuit that compares two input voltages and produces an output voltage determined by external feedback components. When configured with negative feedback, the closed-loop gain is established primarily by external resistors. Operational amplifiers can also be used as voltage buffers, comparators, current-to-voltage converters, instrumentation stages, and active filters. The LM358PSR therefore belongs to the broader hierarchy of analog ICs, amplifiers, voltage amplifiers, and general-purpose operational amplifiers. The principal feature of the LM358PSR is its dual-circuit integration. Two amplifiers in one package can simplify dual-channel signal conditioning, balanced sensing, feedback control, and audio or industrial analog interfaces. Its 8-SO package supports conventional surface-mount PCB assembly rather than through-hole insertion. Each amplifier requires suitable input and feedback components, and the circuit must remain within the voltage, current, temperature, and common-mode limits specified by the manufacturer datasheet. The LM358 family is widely encountered in general-purpose analog designs because one device can implement multiple common analog functions. Typical uses include amplifying sensor outputs, buffering inputs to analog-to-digital converters, driving slow-changing signals, forming difference-amplifier stages, and building active filtering or gain-control blocks. A dual package can reduce the number of IC footprints compared with two separate single amplifiers. Because the two circuits share one package, their power-supply connections, operating limits, thermal environment, and layout requirements are linked. Designers should place bypass capacitors near the supply pins, route sensitive input and feedback paths away from noisy switching nodes, and confirm that the amplifier remains stable with the selected output-load and feedback network. The manufacturer datasheet should guide the final supply, resistor, capacitor, and layout selections. This page brings together the LM358PSR package identity, commercially relevant sourcing questions, verified drop-in candidates, comparison points, and practical PCB guidance. It is intended to help engineers identify whether the dual 8-SO amplifier fits a board before finalizing component documentation, footprint checks, and prototype assembly.

RFQ Contact
LM358PT - Dual 3-32V Op Amp, 1.1MHz | STMicroelectronics
LM358PT

LM358PT - Dual 3-32V Op Amp, 1.1MHz | STMicroelectronics

The STMicroelectronics LM358PT is a dual general-purpose operational amplifier containing two independent, internally frequency-compensated amplifiers. Its 3 V to 32 V single-supply operating range, 1.1 MHz unity-gain bandwidth, 100 dB DC voltage gain, and low input common-mode voltage of 0.6 V make it suitable for general signal conditioning. The device is supplied in an 8-pin TSSOP surface-mount package. An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its inverting and non-inverting inputs. The LM358 belongs to the dual-operational-amplifier category within the broader amplifier IC and analog semiconductor hierarchy. Its two independent channels can amplify AC or DC signals, buffer inputs, perform comparisons, and support feedback-based circuit functions. Internal frequency compensation simplifies stable operation without an external compensation network. The principal features of the LM358PT include two amplifier channels in one package, a wide 3 V to 32 V supply range, 1.1 MHz unity-gain bandwidth, and 100 dB large-signal DC voltage gain. Internally compensated operation supports practical use without external compensation capacitors. The 8-pin TSSOP package also provides a compact surface-mount option for industrial control, instrumentation, sensor interfaces, and consumer equipment where board area matters. Technically, the LM358PT is designed for single-supply operation while accepting input signals close to the lower supply rail. The verified 0.6 V input common-mode figure gives designers a concrete limit when working from a 3 V or 5 V rail. Its bandwidth is sufficient for many audio, control, and instrumentation signals, but it is not a high-speed precision op amp. Applications requiring very low offset, very low noise, rail-to-rail output, fast slew rate, or high DC accuracy should be reviewed against the device limits before production release. Typical uses include sensor-signal conditioning, active filtering, transducers, relay and solenoid drivers, audio and communications interfaces, and general control loops. The two channels can process related signals in a compact circuit or implement separate functions. Because output-current capability and slew-rate limits remain important in real designs, the load should be checked against the manufacturer's operating information rather than assumed from the wide supply range. A key design consideration is input common-mode range: the LM358PT can operate from 0.6 V above the negative supply, but it does not provide true rail-to-rail input or output swing. Designers should also account for the effects of supply bypassing, output loading, stability with capacitive loads, and the power dissipation created by the voltage difference across each amplifier. This product record combines manufacturer and distributor information with a practical selection guide, package-aware alternatives, comparison parameters, and implementation notes. It is intended to help engineers confirm footprint, electrical fit, sourcing status, and application suitability before selecting LM358PT for a PCB redesign or new design.

RFQ Contact
LM358PW - Dual 16-32V Op Amp | Texas Instruments
LM358PW

LM358PW - Dual 16-32V Op Amp | Texas Instruments

The Texas Instruments LM358PW is a dual general-purpose operational amplifier with two independent amplifier circuits, a wide ±16 V to ±32 V supply range, and an 8-pin TSSOP package. Designed for low-power consumption and high open-loop gain, it is suitable for signal conditioning, feedback control, and analog signal amplification across industrial, consumer, and instrumentation systems. Each amplifier can operate from a single supply or from split positive and negative supplies. An operational amplifier is an analog semiconductor that uses high-gain differential feedback to amplify the difference between two input voltages. The LM358 belongs to the dual operational-amplifier, voltage-feedback, analog IC, and power-management signal-chain hierarchies. Its two channels share common supply pins but otherwise provide independent amplifier functions, allowing one package to implement two signal-processing paths. The principal advantages of the LM358PW are its dual-channel integration, low-power operation, high gain, broad supply-voltage range, and established industry-standard pin arrangement. The TSSOP-8 footprint saves board area compared with larger dual-op-amp packages, while two channels reduce the component count in designs that require duplicated gain or buffering stages. These characteristics make the device a practical baseline for general-purpose analog designs. Its architecture is suited to voltage-feedback applications in which the amplifier operates with external negative feedback. The package provides separate inputs and outputs for both channels, while the power terminals are shared. Designers should account for input common-mode limits, output swing, bias current, noise, slew rate, stability, and load capability when setting the operating point; consult the manufacturer datasheet for exact limits and test conditions before finalizing a circuit. Typical applications include DC signal conditioning in sensor interfaces, closed-loop control for industrial equipment, audio preamplification, analog sensor amplification, and general buffer stages. The two-amplifier configuration is especially useful when a board needs one channel for signal amplification and another for filtering, level shifting, active feedback, or output buffering. The primary design consideration is circuit stability. Feedback-network values, source and load impedances, output loading, and supply bypass capacitance affect closed-loop performance. Place the required decoupling capacitor close to the supply pins, use short feedback paths, and verify common-mode and output-swing margins across the intended input range. Add input or output protection when external wiring can introduce transients beyond the device ratings. This product page combines the manufacturer product description, distributor package and catalog information, documented cross-reference candidates, and practical application guidance. It also highlights the distinction between electrically similar devices and true TSSOP-8 drop-in options, helping engineers evaluate footprint compatibility, temperature behavior, supply range, and channel-level performance before redesigning an existing PCB.

RFQ Contact
LM358PWG4 - Dual 700kHz Op Amp, 16V, TSSOP-8 | Texas Instruments
LM358PWG4

LM358PWG4 - Dual 700kHz Op Amp, 16V, TSSOP-8 | Texas Instruments

The Texas Instruments LM358PWG4 is a dual general-purpose operational amplifier with two independent amplifiers, 700 kHz gain-bandwidth product, and 0.3 V/us slew rate. Designed for single or dual supply operation, it accepts a 3 V to 32 V total supply range and is packaged in an 8-pin TSSOP. The LM358PWG4 is supplied in tube packaging for a 0°C to 70°C commercial operating-temperature grade. An operational amplifier is an analog signal-processing IC that compares its inverting and non-inverting inputs and amplifies the voltage difference between them. Within the broader semiconductor hierarchy, an op amp is an amplifier IC and part of the analog signal-conditioning family. The dual configuration in the LM358PWG4 places two general-purpose amplifiers in one package, reducing component count and board area in designs that need two similar signal-processing channels. The key operating characteristics are a 700 kHz gain-bandwidth product, 0.3 V/us slew rate, and operation from 3 V to 32 V. The documented output-swing range extends from approximately ±1.5 V to ±16 V depending on supply conditions and load. Its general-purpose architecture makes it suitable for conventional amplifier, comparator, summing, and feedback applications where moderate bandwidth and broad supply compatibility are more important than rail-to-rail input or output operation. The LM358 family is particularly useful when two independent channels can share a common supply. Because both amplifiers are in the same package, board designers can shorten supply routing and maintain symmetrical placement of the two channels. The 8-pin TSSOP package also supports compact PCB construction, although its narrow lead pitch requires careful assembly and adequate solder-joint inspection. Typical uses include audio preamplification, sensor-signal conditioning, low-frequency active filters, comparators with pull-up resistors, and general instrumentation. In these applications, the 700 kHz bandwidth handles low- and mid-frequency signals, while the 0.3 V/us slew rate helps control distortion for moderate-amplitude signals. The broad 3 V to 32 V supply range also supports both low-voltage portable systems and higher-voltage industrial control systems. Designers should evaluate output swing, input common-mode range, bias current, offset voltage, noise, and stability for the exact operating conditions before assigning gain or filter coefficients. Decoupling capacitors should be placed close to the supply pins, and unused amplifier inputs should be biased so they remain in a defined common-mode state. The two channels are independent, but sharing a package does not guarantee matched behavior. This product page combines the verified LM358PWG4 electrical and packaging characteristics with application guidance, replacement considerations, and practical selection criteria. It helps engineers identify where the dual 700 kHz amplifier, 3 V to 32 V supply capability, and compact TSSOP-8 package provide useful design advantages without overlooking rail-range or precision requirements.

RFQ Contact
LM358PWR - Dual Op Amp, 700kHz, TSSOP-8 | Texas Instruments
LM358PWR

LM358PWR - Dual Op Amp, 700kHz, TSSOP-8 | Texas Instruments

The Texas Instruments LM358PWR is an industry-standard dual operational amplifier integrating two general-purpose op-amp circuits in a single 8-pin TSSOP (PW) surface-mount package. Each amplifier offers a 700 kHz gain-bandwidth product, a 0.3 V/us slew rate, and operates from supply rails of ±1.5 V to ±16 V (or a single supply from 3 V to 32 V), making it one of the most widely deployed analog building blocks in electronics. A dual operational amplifier is an analog integrated circuit that combines two independent, internally frequency-compensated, high-gain voltage amplifiers on one die. In the signal-chain hierarchy, an op amp is a foundational linear amplifier used to build gain stages, filters, comparators, integrators, current sinks, and voltage followers; the dual format halves board space and sharing one bias network improves thermal matching between channels. Key features of the LM358PWR include common-mode input range extending to ground (a single-supply capability that many older op amps lack), high differential input voltage capability, and operation across both single and split supplies. The TSSOP-8 package measures roughly 6.4 mm x 4.4 mm with a 0.65 mm pitch, supporting compact surface-mount assemblies. Architecturally, the LM358 uses an internally compensated bipolar design with a PNP differential input stage referenced to the negative rail, which is what allows inputs to operate down to 0 V in single-supply systems. The output stage sources and sinks current with a characteristic output swing that reaches near the negative rail. Typical applications include transducer amplification, DC gain blocks, active filters, voltage comparators, LED drivers, and sensor signal conditioning in industrial controls, consumer appliances, and automotive body electronics (where the related LM2904 variant is common). A key design consideration: the input offset voltage of the bipolar LM358 input stage (typically a few millivolts) limits precision; for sub-millivolt accuracy, consider the next-generation LM358B, which shares the same pinout with improved specifications. This page consolidates verified specifications, pin-to-pin alternatives, application guidance, and design notes in one place - content that goes beyond what a raw datasheet listing provides.

RFQ Contact
LM358PWRG3 - Dual 16V 700kHz Op Amp | Texas Instruments
LM358PWRG3

LM358PWRG3 - Dual 16V 700kHz Op Amp | Texas Instruments

Texas Instruments LM358PWRG3 is a standard general-purpose dual operational amplifier with two amplifier circuits, a 700 kHz gain-bandwidth product, and a 16 V maximum supply rating. It is packaged in an 8-TSSOP for surface-mount assembly. The LM358 family is a widely used general-purpose op-amp platform for low-frequency analog signal conditioning, sensor interfaces, and basic amplifier configurations. An operational amplifier is a high-gain, differential-input analog IC used to amplify voltage differences. In its broader hierarchy, an operational amplifier belongs to the amplifier-IC and analog-signal-chain categories. A dual op amp integrates two amplifier channels into one package, allowing a design to use both channels for related tasks such as signal conditioning, buffering, filtering, or feedback control. The LM358PWRG3 combines that two-channel architecture with a compact TSSOP-8 footprint. The identified part is a standard, general-purpose device rather than a rail-to-rail precision amplifier. Its stated 700 kHz gain-bandwidth product supports applications where the closed-loop bandwidth is substantially lower after accounting for the selected noise gain. The 16 V maximum supply rating places the device in the single-supply operating class shown by the product listing. Tape-and-reel packaging supports automated pick-and-place and high-density PCB assembly. The dual-channel organization can reduce component count when a board needs two related amplifier functions. One channel might condition a sensor output while the other provides buffering or active feedback, although the final circuit must satisfy the device's input, output, common-mode, stability, and load requirements described in the manufacturer datasheet. The 8-TSSOP package offers a smaller board area than an SOIC-8 package, but its lead pitch requires careful component placement and assembly planning. Typical application areas include transducer signal conditioning, low-frequency closed-loop control, analog sensor interfaces, active filters, and general buffer or gain stages. In a sensor interface, the op amp may amplify a small differential signal before downstream conversion. In a filter, its gain and bandwidth behavior participate in setting the transfer function. In a feedback-control circuit, the dual package can support related signal paths without requiring two separate single-channel packages. Designers should follow the manufacturer datasheet for the complete electrical limits, pin assignments, common-mode range, output-swing limits, input-bias-current behavior, noise characteristics, and recommended operating conditions. Decoupling and layout decisions should be based on the intended circuit topology, especially when the amplifier drives capacitive loads or operates close to supply rails. PCB signal-return paths should remain short and preserve a low-impedance ground connection. This page combines the exact package and headline device information with practical selection guidance, verified source links, an explicit data-completeness assessment, and engineering-focused application notes. It also distinguishes pin-compatible alternatives from broader functional equivalents so engineers can make a replacement decision without assuming that similar amplifier performance guarantees footprint, bias, stability, or operating-range compatibility.

RFQ Contact
LM358PWRG4 - Dual 700 kHz Op Amp, 30 V, TSSOP-8 | TI
LM358PWRG4

LM358PWRG4 - Dual 700 kHz Op Amp, 30 V, TSSOP-8 | TI

Texas Instruments LM358PWRG4 is a dual general-purpose operational amplifier with two independent amplifiers, 30 V maximum supply capability, 700 kHz gain-bandwidth product, and an 8-pin TSSOP package. The LM358PWRG4 is designed for cost-sensitive applications requiring one amplifier that can operate from a single supply, accept input signals near ground, and provide reasonably wide common-mode input range. Both channels share the same supply pins and are not intended for direct parallel operation. An operational amplifier is a high-gain differential amplifier used to compare, amplify, filter, buffer, or scale signals. The LM358 belongs to the operational-amplifier hierarchy within analog signal-chain ICs and broader semiconductor devices. Its internal frequency compensation removes the need for an external compensation capacitor in most closed-loop configurations, simplifying PCB layout and reducing the component count in cost-sensitive industrial, consumer, instrumentation, and control designs. The principal features of the LM358PWRG4 include a dual-amplifier configuration, 700 kHz gain-bandwidth product, 0.3 V/us slew rate, 3 V typical low supply-current drain, approximately 3 mV typical input offset voltage, and approximately 2 nA typical input offset current. Its common-mode input range can include ground, making it useful in single-supply sensor interfaces where the signal begins near 0 V. The 30 V maximum supply rating provides additional operating margin compared with devices limited to lower supply voltages. Internally, the LM358 uses a bipolar transistor input and output stage optimized for economy and supply-voltage flexibility rather than rail-to-rail input or output operation. The amplifiers are frequency-compensated for stable operation with external feedback networks. Because output swing and input common-mode range are not rail-to-rail, a designer should check the signal amplitudes and output voltage required by the selected feedback network, especially with low supply voltages. Typical uses include low-cost sensor-signal conditioning, current-loop and grounded-transducer interfaces, audio preamplification, voltage comparators, active filters, motor and relay control, industrial equipment, and general-purpose analog modules. The TSSOP-8 footprint supports compact, high-density PCB layouts, while the dual channel can implement two matched amplifier functions or one differential amplifier followed by a separate amplifier stage. The main design consideration is supply headroom. Check input common-mode limits, differential input limits, output swing, load capability, and stable feedback gain for the actual supply voltage. Place bypass capacitors close to the supply pins and maintain a short, quiet output path, especially when the amplifier drives a long trace or an ADC input. Because the part is listed at last-time-buy status, production designs should evaluate an explicitly qualified second source rather than assume unlimited lifecycle availability. This page combines the exact LM358PWRG4 ordering information, technical characteristics, lifecycle status, package details, and engineering guidance into one purchasing reference. It also identifies same-footprint alternatives and explains where analog-performance qualification must be checked before substitution.

RFQ Contact
LM358PWRG4-JF - Dual 30V 700kHz Op Amp | Texas Instruments
LM358PWRG4-JF

LM358PWRG4-JF - Dual 30V 700kHz Op Amp | Texas Instruments

Texas Instruments LM358PWRG4-JF is a dual, general-purpose bipolar operational amplifier with a 30 V power-supply rating, 700 kHz gain-bandwidth product, and two amplifier circuits in an 8-pin TSSOP (PW) package. The device operates from single or dual supplies, with listed operating ratings of 0°C to 70°C and a maximum input offset voltage of 9,000 µV. An operational amplifier is an analog semiconductor that amplifies the voltage difference between its two inputs. The LM358 belongs to the dual-operational-amplifier hierarchy within the broader voltage-feedback amplifier, analog IC, and semiconductor categories. Its two channels may be used independently, or one channel can provide amplification while the other performs a related task such as buffering, level shifting, or active filtering. The LM358PWRG4-JF provides a 30 V maximum supply voltage, 700 kHz gain-bandwidth product, and bipolar input and output stages. A 700 kHz bandwidth supports general-purpose signal conditioning across audio, industrial-control, instrumentation, and data-acquisition circuits. The 9,000 µV maximum input offset voltage is appropriate for applications in which moderate DC offset does not dominate the measurement or control accuracy. The dual configuration offers better functional density than two single amplifiers. Its 8-pin TSSOP package supports compact surface-mount assembly, while the two amplifier sections make it practical to process related signals with one component. Designers should still account for common-mode range, output swing, input bias current, stability, noise, and supply bypass requirements when defining an exact application. Typical uses include low-frequency audio amplification, sensor-signal conditioning, DC error amplification, active filtering, comparators with open-collector outputs, and general industrial analog interfaces. The wide 30 V supply capability is useful where the signal chain operates above conventional 5 V or 12 V rails, provided the common-mode and output-swing limits of the selected amplifier remain satisfied. For implementation, decouple each supply rail close to the device with suitable bypass capacitance and route feedback components to minimize parasitic coupling. Keep output loads within the specified range, avoid violating common-mode limits, and check stability when driving capacitive loads. The 0°C to 70°C rating makes this ordering appropriate for commercial-temperature environments rather than extended industrial or automotive temperature ranges. This page combines the manufacturer identification, distributor technical attributes, package details, replacement considerations, and practical application guidance for engineers evaluating the LM358PWRG4-JF. It also highlights the need to distinguish electrically similar LM358 order codes from confirmed, pin-compatible alternatives before changing a released PCB design.

RFQ Contact
LM358QDRQ1 - Automotive Dual 1MHz Op-Amp SOIC-8 | Texas Instruments
LM358QDRQ1

LM358QDRQ1 - Automotive Dual 1MHz Op-Amp SOIC-8 | Texas Instruments

The Texas Instruments LM358QDRQ1 is an automotive-grade, dual general-purpose operational amplifier qualified to AEC-Q100, delivered in an 8-pin SOIC (0.154 inch, 3.90 mm width) package on tape and reel. Each of the two amplifier channels offers a gain bandwidth product of approximately 1 MHz with rail-friendly output swing suited to single-supply operation, making it a workhorse signal-conditioning amplifier for 12V automotive and 5V industrial systems. An operational amplifier (op-amp) is a high-gain voltage amplifier with differential inputs and a single-ended output; within the component hierarchy it belongs to the amplifier IC family, under integrated circuits, and is a core building block of analog signal chains. Dual op-amps such as the LM358-Q1 integrate two independent channels in one package, halving board area versus two single amplifiers while sharing supply rails. Key features include two independent amplifier circuits, a 1 MHz class gain bandwidth, low input offset suitable for general-purpose sensing, operation from single or dual supplies, and AEC-Q100 automotive qualification with temperature grading that supports harsh under-hood environments. The wide supply range allows direct interfacing with battery-backed rails and regulated 5V logic domains. Architecturally, the LM358-Q1 family traces to the classic LM358 bipolar design updated for automotive quality systems, with TI manufacturing controls per its automotive flow; the related LMV358-Q1 variant adds rail-to-rail output for low-voltage rails per the LMV321-Q1/LMV358-Q1/LMV324-Q1 datasheet. Typical applications include automotive sensor signal conditioning, current-sense amplification front-ends, active filters, comparators and level shifters, and battery-management monitoring stages in vehicle ECUs and industrial controllers. Design tip: with a 1 MHz GBW, keep closed-loop gains modest (10x or below) to preserve bandwidth and phase margin; check the output swing versus load, since the classic LM358 output does not reach the positive rail.

RFQ Contact
LM358QT - Dual Op-Amp 1.1MHz DFN-8 | STMicroelectronics
LM358QT

LM358QT - Dual Op-Amp 1.1MHz DFN-8 | STMicroelectronics

The STMicroelectronics LM358QT is a low-power dual operational amplifier integrating two independent, high-gain, internally frequency-compensated op-amp circuits in an 8-pin UFDFN exposed-pad package measuring 2x2 mm. It delivers a gain-bandwidth product of 1.1 MHz (temperature compensated), a slew rate of 0.6 V/us, and a large DC voltage gain of 100 dB, operating from a single supply of 3 V to 30 V or dual supplies of +/-1.5 V to +/-15 V. An operational amplifier is a high-gain DC-coupled voltage amplifier with differential inputs and a single-ended output. As a member of the linear amplifier / signal conditioning IC family within analog semiconductor hierarchy, the general-purpose dual op-amp is one of the most widely used building blocks in electronics, performing amplification, active filtering, buffering, level shifting, and comparator-like threshold detection in virtually every analog signal chain. Key differentiating features include internally frequency compensation (no external compensation components required), very low supply current per amplifier for battery-powered designs, low input bias current of 20 nA, and unity-gain stability across the full industrial temperature span. The wide 3 V to 30 V single-supply range allows direct operation from logic supplies or automotive rails through simple regulation. Architecturally, the LM358QT consists of two independent, high-gain op amps sharing a common supply pin pair. The internally compensated bipolar design guarantees stability at unity gain without external capacitors, while the exposed-pad DFN-8 package provides a low thermal resistance path to the PCB, supporting compact, high-density layouts where SOIC-8 footprints are too large. Typical applications include transducer amplifiers and sensor signal conditioning, DC gain blocks and active filters in industrial controls, and battery-powered consumer or portable instrumentation where quiescent drain matters. It also serves as a summing amplifier, integrator, or voltage follower in general-purpose analog front ends. Design consideration: as a general-purpose bipolar-input op amp, the LM358QT is not a precision part; for microvolt-level offset or high-speed requirements, select a dedicated precision or high-bandwidth amplifier. Ensure the common-mode input range and output swing limitations near the rails are respected in single-supply designs. This page consolidates verified datasheet parameters, drop-in alternatives, pricing context, and practical design notes not found in the manufacturer datasheet alone.

RFQ Contact
LM358S-13 - Dual Low-Power Op Amp, 3-32V | Diodes Incorporated
LM358S-13

LM358S-13 - Dual Low-Power Op Amp, 3-32V | Diodes Incorporated

Diodes Incorporated LM358S-13 is a dual, low-power operational amplifier containing two independent high-gain, internally frequency-compensated amplifiers. It operates from a single supply over a 3 V to 32 V range, provides a gain bandwidth of 100 dB as identified by Mouser, and is packaged in an 8-pin surface-mount SO package. The two amplifier channels can be used independently for signal conditioning, voltage comparison, feedback control, or general-purpose analog functions. An operational amplifier is an analog signal-processing IC that compares voltages applied to its inverting and non-inverting inputs and amplifies the difference between them. The LM358 family belongs to the dual operational amplifier category within the broader hierarchy of amplifiers, analog ICs, and semiconductor devices. Its internally compensated architecture simplifies closed-loop design because no external compensation components are required for ordinary voltage-feedback operation. The principal benefits of the LM358S-13 are its wide single-supply operating range, dual-channel integration, low-power designation, and internally frequency-compensated architecture. Two independent amplifiers in one package reduce component count and board area compared with two separate single operational amplifiers. Its 3 V minimum supply supports lower-voltage systems, while the 32 V maximum permits connection to conventional higher-voltage industrial rails when appropriate protection and signal limits are respected. The LM358 series was designed specifically for operation from a single power supply. In a single-supply circuit, the common or supply-return node is the reference for signal inputs, so input and output voltages must remain within the device's operating limits. Grounding inputs near the common node is important when processing small signals because the output cannot swing below the lower rail. The second amplifier can complement the first as an inverter, comparator, transimpedance amplifier, or buffer in the same package. Typical applications include low-voltage sensor interfaces, DC signal amplification, threshold detection, loop-error amplification, transducer buffering, and general dual-channel analog conditioning. The 8-pin SO package is suitable for compact surface-mount PCB assemblies, although exact connector and test-point placement should follow the manufacturer's pin configuration. Decoupling capacitors should be placed close to the supply pins, and sensitive analog traces should remain away from switching nodes and high-current return paths. Design trade-offs must be checked against the complete electrical characteristics before production use. In particular, input common-mode range, output swing, input bias current, input offset voltage, supply-current behavior, noise, and output-current capability determine whether a particular application is electrically suitable. This page combines the confirmed product identity and electrical headline values with package guidance, drop-in comparison information, application patterns, and practical layout recommendations for faster engineering evaluation.

RFQ Contact
LM358SNG - Dual Op-Amp, 3-32V, 8-PDIP | onsemi
LM358SNG

LM358SNG - Dual Op-Amp, 3-32V, 8-PDIP | onsemi

The onsemi LM358SNG is a single-supply dual operational amplifier with two independent general-purpose amplifier circuits in an 8-pin PDIP (0.300 in, 7.62 mm) package. It operates from a 3V to 32V single supply (or ±1.5V to ±16V dual supplies) and features a low input bias current of 45 nA, making it a classic value-line bipolar op-amp for cost-sensitive analog designs. A general-purpose operational amplifier is an analog building block that amplifies the voltage difference between its two inputs with high open-loop gain and is configured for gain, filtering, buffering, or comparison through external passive components. Op-amps sit at the core of the analog signal chain hierarchy: op-amp -> amplifier IC -> linear/analog IC -> semiconductor, and the LM358 family was the first industry-standard dual op-amp optimized for single-supply operation. Key features include dual matched amplifiers sharing one bias network for low offset drift, an input common-mode range that includes ground (true single-supply capability), and wide supply operation from 3V to 32V. The two circuits are internally matched, which reduces quiescent power per amplifier and simplifies dual-channel designs on a single rail. Technically, the LM358SNG uses bipolar process technology with internal frequency compensation, so it is unity-gain stable without external capacitors. The output stage can source and sink current to ground on a single rail, though output swing is limited to within roughly one diode drop of the negative rail. This makes it well suited to low-frequency analog front ends rather than high-speed signal processing. Typical applications include transducer signal conditioning, DC gain blocks and active filters, voltage comparators and level detection, current sensing on single-supply microcontroller boards, and audio preamp stages in battery-powered equipment where a single positive rail must be used. When designing with this device, reserve gain-bandwidth-limited topologies to audio-range frequencies and always provide a supply decoupling capacitor close to pin 8. For precision designs, verify input offset voltage over temperature because value-line bipolar input stages drift more than modern precision CMOS parts. This page synthesizes distributor availability, drop-in alternatives, package pinout, and practical design notes in one place, going beyond a plain datasheet listing.

RFQ Contact
LM358ST - Dual General-Purpose Op Amp | STMicroelectronics
LM358ST

LM358ST - Dual General-Purpose Op Amp | STMicroelectronics

STMicroelectronics LM358ST is a dual, general-purpose operational amplifier with two independent, internally frequency-compensated amplifiers, an 800 kHz gain-bandwidth product, and an 8-TSSOP package. The device operates from a single power supply over a wide voltage range and is also specified for operation at supply voltages up to ±16 V, corresponding to a total supply range of 32 V. An operational amplifier is an analog signal-conditioning IC that uses differential feedback to amplify the voltage difference between its inverting and non-inverting inputs. The LM358 belongs to the general-purpose operational-amplifier family, which sits within the broader amplifier IC and semiconductor hierarchy. Its two independent channels allow one package to provide separate amplification paths for sensors, control loops, audio stages, or general analog signal processing. The principal features of the LM358ST include two independent amplifier circuits, internally integrated frequency compensation, a common-mode input range that includes ground, and low-power operation from a single supply. The 800 kHz bandwidth supports general-purpose closed-loop signal paths without requiring an external compensation network. Its 8-pin TSSOP format provides a compact surface-mount option for mixed-signal boards with limited routing area. Each channel uses a differential input stage and an internally compensated voltage-feedback architecture. Because the channels are independent, one can amplify a sensor signal while the other performs filtering, comparison, level conversion, or feedback control. Common-mode operation near ground is particularly useful for circuits powered from a single positive rail, where input signals may remain close to 0 V. Designers should still verify input and output swing against the specific supply voltage used in the final circuit. Typical uses include low-side current sensing, sensor amplification, audio and communications interfaces, industrial control, and embedded instrumentation. In an STM32-based measurement system, the two channels can condition separate analog inputs before conversion by the microcontroller. The device can also implement active filters or comparators because its outputs can typically swing close to ground when operated from a positive single supply. For PCB design, place input resistors, feedback components, and bypass capacitors close to the relevant pins to reduce parasitic feedback and noise pickup. A local supply decoupling capacitor should be positioned near pin 8, with the ground return routed directly to pin 4. Check input common-mode voltage, output swing, stability with the intended feedback network, and channel thermal dissipation before committing the layout. This product page combines the exact LM358ST package and electrical identity with sourcing guidance, genuine drop-in options, pin assignments, and practical application notes. It is intended to help engineers compare footprint, function, supply range, bandwidth, and design constraints faster than a raw distributor listing while preserving manufacturer datasheet requirements for final qualification.

RFQ Contact
LM358TP/NOPB - Dual Op Amp, 32 V, 8-DSBGA | Texas Instruments
LM358TP/NOPB

LM358TP/NOPB - Dual Op Amp, 32 V, 8-DSBGA | Texas Instruments

The Texas Instruments LM358TP/NOPB is a dual general-purpose operational amplifier packaged in an 8-DSBGA package. It provides two amplifier channels, operates from single or dual supplies with a total input range up to 32 V, offers a 1 MHz gain-bandwidth product, and supports a 0°C to 70°C commercial temperature range. Its 85 dB open-loop gain and 2 mV typical input offset voltage suit cost-sensitive signal-conditioning, buffering, and control applications. An operational amplifier is an analog integrated circuit that uses high open-loop gain to amplify the difference between two input voltages. Negative feedback causes the amplifier to operate as a closed-loop gain stage, while internal compensation makes many standard closed-loop configurations possible without external compensation components. The LM358 combines two such amplifier sections in one package, reducing board area compared with two separate single-amplifier devices. The principal characteristics include a 1 MHz gain-bandwidth product, approximately 85 dB open-loop gain, a typical input offset voltage of 2 mV, and input bias current values of approximately 45 nA to 50 nA. The device operates from 3 V to 32 V, supports positive and negative signal operation around ground, and has an input common-mode range extending from negative supply voltage to positive supply voltage minus approximately 1.5 V. These characteristics make it suitable for low- and medium-bandwidth analog systems. The LM358 architecture is designed for straightforward general-purpose analog use. Its two channels can operate independently, allowing simultaneous signal conditioning, voltage comparison, current-to-voltage conversion, or cross-coupled amplifier arrangements. Because the gain-bandwidth product is 1 MHz, closed-loop bandwidth decreases as the selected noise gain rises. Designers should account for this relationship when selecting resistor values, filtering bandwidth, and required settling time. Typical applications include current sensing in industrial control systems, sensor signal conditioning in instrumentation, audio and communication interface circuits, active filtering, comparator-style threshold detection, and low-voltage control systems. The 1.3 mm by 1.3 mm DSBGA package supports compact layouts, although its fine pitch requires capable assembly processes, careful solder-paste control, and adequate thermal and assembly design. For single-supply designs, place the unused amplifier input close to a defined common-mode potential rather than leaving it floating. Use the manufacturer's pin-description table when assigning tracks and provide local supply bypassing to limit supply-induced disturbance. Ensure the output current, input common-mode voltage, and total supply voltage remain within the ratings for the selected operating conditions. This product data combines the electrical characteristics, package details, comparison parameters, and practical design guidance needed to evaluate the LM358TP/NOPB. The same-package substitution search is intentionally conservative because conventional LM358 replacements commonly use different packages, making them unsuitable as literal drop-in replacements for this 8-DSBGA footprint.

RFQ Contact
LM358TPX/NOPB - 2-Channel 1MHz 32V Op Amp | Texas Instruments
LM358TPX/NOPB

LM358TPX/NOPB - 2-Channel 1MHz 32V Op Amp | Texas Instruments

Texas Instruments LM358TPX/NOPB is a two-channel, general-purpose operational amplifier with a 1 MHz gain-bandwidth product, 32 V maximum supply capability, and an 8-DSBGA package. Each channel is a high-gain, internally frequency-compensated amplifier designed for single-supply operation, with typical performance figures including 65 dB common-mode rejection, 0.1 V/us slew rate, approximately 500 uA supply current per amplifier, and 2 mV input offset voltage. An operational amplifier is a high-gain analog building block used to amplify, buffer, compare, or sum signals. The dual-amplifier configuration provides two independent channels in one package, reducing board area when a circuit needs two general-purpose amplifier functions. Internally frequency compensation makes the devices straightforward to use for stable closed-loop gains without external compensation components, while the wide supply-voltage range supports both low-voltage and higher-voltage industrial designs. The 1 MHz gain-bandwidth product is suitable for audio, control, sensing, and signal-conditioning circuits that do not require high-speed operation. A 65 dB common-mode rejection ratio helps reject equal-mode interference, and the 0.1 V/us slew rate defines useful large-signal bandwidth for moderate-frequency waveforms. The 500 uA supply current per amplifier supports low-power signal paths, while the 32 V maximum rating provides additional headroom in applications using higher supply rails. The LM358 family architecture supports operation from a single positive supply or a split supply. Because each amplifier is independent, one channel can perform one function while the other performs a separate function. The 2 mV typical input offset voltage is suitable for many cost-sensitive general-purpose designs, although precision measurement systems should account for offset, bias current, noise, and temperature drift in their error budget. Typical uses include microphone preamplification, sensor signal conditioning, battery-powered monitoring, current-loop interfaces, comparator-style threshold detection, and general DC signal amplification. The 8-DSBGA format is useful where PCB area is constrained, but its small land pattern requires careful assembly and adequate thermal design. The tape-and-reel ordering option also supports automated production handling. For reliable layout, place input, output, and supply connections to minimize parasitic resistance and capacitance. Keep sensitive input traces short, provide local supply bypassing, and verify the exposed-ball thermal path against the PCB copper area. Designers should also account for input common-mode limits and output-current limits; the amplifier does not operate as a rail-to-rail input or output device. This product page organizes the key electrical characteristics, package information, sourcing terms, replacement constraints, and engineering guidance for the LM358TPX/NOPB. It also distinguishes same-footprint alternatives from broader LM358-family devices whose packages or electrical operating limits require a different design review.

RFQ Contact
LM358WPT - Dual 5V 1.1MHz Op Amp | ROHM | TSSOP-8
LM358WPT

LM358WPT - Dual 5V 1.1MHz Op Amp | ROHM | TSSOP-8

The ROHM Semiconductor LM358WPT is a dual general-purpose operational amplifier with two independent, internally compensated amplifiers in an 8-pin TSSOP package. Rated for a nominal 5 V supply, it supports single-supply operation from 3 V to 36 V or split-supply operation up to plus or minus 16 V. Key characteristics include a 1.1 MHz gain-bandwidth product, approximately 800 kHz small-signal bandwidth, and a 0.3 V/us slew rate. An operational amplifier, or op amp, is an analog signal-processing IC that amplifies the difference between two input voltages while providing high open-loop gain, negative feedback support, and output-voltage drive. The LM358WPT belongs to the hierarchy dual operational amplifier -> general-purpose amplifier -> analog amplifier IC -> semiconductor. Its common-mode input range can extend toward the negative supply rail, making it useful in single-supply sensor, audio, and control circuits. The LM358WPT integrates two independent amplifiers, allowing one package to implement stereo audio channels, dual-axis sensing, active filtering, or two-stage signal conditioning. Each channel uses standard industry-style pin assignments for dual op amps: two inputs, one output, and shared positive and negative supply connections. Internal compensation removes the need for external frequency-compensation components in typical closed-loop designs. At a nominal 5 V supply, the device combines a usable gain-bandwidth product of 1.1 MHz with a 0.3 V/us slew rate. This bandwidth supports audio-frequency and general feedback-control applications rather than high-speed signal conditioning. The large operating-supply range also permits direct interfacing with higher-voltage industrial systems, subject to the input and output common-mode limits and the device's absolute maximum ratings. Typical uses include microphone preamplification, transducers with ground-referenced outputs, loop-control systems, transducers, and general-purpose amplification. Because the output can source and sink current within the supply limits, the part also serves as an output-buffer stage when the load is not too heavy. When designing a PCB around the LM358WPT, place bypass capacitors close to the supply pins and route sensitive input traces away from switching nodes. Keep the negative supply connection short because common-mode performance and output swing depend on a low-impedance ground reference. Check the full operating-temperature range and load-current limits in the manufacturer datasheet before using the amplifier in extended-temperature equipment. This page consolidates package details, supply-range information, pin assignments, drop-in replacement candidates, and application guidance into a practical engineering reference. It also organizes the main design trade-offs so that engineers can compare bandwidth, supply capability, and package reuse before committing a PCB footprint.

RFQ Contact
LM358YPT - Dual 1.1MHz Low-Power Op Amp | STMicroelectronics
LM358YPT

LM358YPT - Dual 1.1MHz Low-Power Op Amp | STMicroelectronics

The STMicroelectronics LM358YPT is a low-power dual operational amplifier packaged in an 8-pin TSSOP. It provides two independent amplifier channels, a 1.1 MHz gain-bandwidth product, and a maximum input offset voltage of 9 mV. The device is identified as a standard general-purpose amplifier and is listed as RoHS compliant. Its dual-channel architecture makes it suitable for signal conditioning, sensor amplification, filtering, and other low-frequency analog circuits that require two amplifiers in one package. An operational amplifier is an analog integrated circuit that amplifies the difference between its inverting and non-inverting inputs. The LM358 belongs to the broader operational amplifier and amplifier IC hierarchy, where it occupies a general-purpose, low-power position rather than a precision or high-speed niche. Two independent amplifiers can process separate signals or be connected together for differential, gain, filtering, or feedback configurations, reducing component count and simplifying dual-signal analog front ends. The principal operating characteristics include a 1.1 MHz gain-bandwidth product, a maximum offset voltage of 9 mV, two amplifier circuits, and an 8-TSSOP package. The low-power description makes the device relevant to battery-operated and low-voltage equipment, while its dual organization improves PCB utilization when both channels are required. RoHS compliance supports use in electronic assemblies whose material restrictions are part of the manufacturing process. As a general-purpose amplifier, the LM358YPT is designed for conventional closed-loop analog applications rather than demanding precision, high-speed, or high-accuracy measurement channels. Designers should use the manufacturer datasheet for the complete electrical limits, input common-mode range, output swing, supply-current limits, compensation details, and recommended operating conditions. Those characteristics determine whether the amplifier maintains useful output swing and linear operation at the selected supply voltage. Typical uses include conditioning resistive sensor signals, buffering higher-impedance circuit nodes, amplifying low-frequency communications signals, implementing active filters, and building dual-channel control or monitoring circuits. In each case, the 1.1 MHz bandwidth provides a practical ceiling for low-frequency gain and closed-loop response, while the offset specification must be considered when signal accuracy matters. A key design consideration is input and output stability around the selected supply rails. Place bypass capacitance near the supply pins, route feedback components to minimize parasitic coupling, and confirm that the required output voltage remains inside the operating limits. The compact TSSOP package also requires careful assembly practices because its lead pitch limits soldering access. This page combines the exact LM358YPT package and headline electrical characteristics with engineering-focused application guidance, drop-in comparison candidates, PCB considerations, and sourcing information. These details help engineers determine whether the device fits a general-purpose analog design before committing it to a production BOM.

RFQ Contact
LM359M - Dual 400 MHz Norton Amplifier | Texas Instruments
LM359M

LM359M - Dual 400 MHz Norton Amplifier | Texas Instruments

The Texas Instruments LM359M is a dual, high-speed, programmable current-mode Norton amplifier with two independent amplifier circuits, a 400 MHz gain-bandwidth product, and a 60 V/µs slew rate. The LM359M is supplied in a 14-SOIC package and is intended for applications requiring high-frequency operation, user-programmable gain, and flexible feedback arrangements. An operational amplifier is an active analog signal-conditioning device that amplifies the difference between two input voltages while using negative feedback to set closed-loop behavior. The LM359 uses a current-mode, or Norton, input architecture rather than the voltage-input architecture common in conventional voltage-feedback amplifiers. This topology can provide high speed and high gain-bandwidth performance when supported by suitable external current-setting and compensation networks. The LM359 family provides two amplifiers in one package, reducing component count in dual-channel signal paths. Its high gain-bandwidth product makes it useful in video, communications, instrumentation, and active-filter circuits where signal bandwidth matters. The user-programmable gain and frequency characteristics allow circuit designers to tailor amplifier behavior with external resistors and capacitors, although stability must be checked for each selected feedback network. The LM359M is a 14-SOIC device with two amplifier sections, separate supply pins, and exposed package leads for through-hole board assembly or compatible PCB land patterns. Because it is a current-mode amplifier, input bias current, feedback-current selection, compensation, and maximum output swing require attention during design. The 400 MHz gain-bandwidth product does not mean every closed-loop circuit will operate at 400 MHz; usable bandwidth depends on gain, noise, stability, loading, and the external network. Typical uses include wideband video signal conditioning, pulse shaping, communications interfaces, active filters, oscillators, and instrumentation. The device is also suitable for educational and laboratory designs where a programmable high-speed analog amplifier is useful. Designers should begin with the manufacturer LM359 datasheet and verify the recommended external components for the intended gain and frequency response. A key design consideration is that LM359M is not a universal replacement for every voltage-feedback operational amplifier. Feedback topology, input bias-current behavior, compensation, output drive, and supply requirements must be checked against the original circuit. Stable operation also requires careful PCB layout, short feedback paths, suitable bypassing, and controlled parasitic capacitance. This page combines verified manufacturer and distributor information, package and application context, practical design guidance, and clearly identified data gaps. It is intended to help engineers evaluate LM359M for high-speed dual-amplifier designs without confusing its current-mode architecture with conventional voltage-feedback amplifier families.

RFQ Contact
LM359M/NOPB - Dual 400MHz High-Speed Amplifier | TI
LM359M/NOPB

LM359M/NOPB - Dual 400MHz High-Speed Amplifier | TI

Texas Instruments LM359M/NOPB is a dual, high-speed, programmable current-mode Norton operational amplifier with a 400 MHz gain-bandwidth product, 60 V/µs slew rate, 8 µA input bias current, and 40 mA output current per channel, packaged in a 14-SOIC tube package. The part is designed for high-frequency signal-chain work where user-programmable operating characteristics and stable inverting operation are important. The LM359 is an operational amplifier, a voltage-feedback signal-conditioning building block that compares an input signal with a feedback network and produces an amplified output. Its current-mode architecture places emphasis on high-frequency performance rather than the conventional high-impedance voltage-mode input used by many general-purpose amplifiers. The LM359 family therefore belongs to the broader category of analog ICs, operational amplifiers, and high-speed active signal-conditioning devices. Key features include two amplifier circuits on one monolithic IC, a 400 MHz gain-bandwidth product, 60 V/µs slew rate, and programmable amplifier operating characteristics. Each channel is broadbanded for high-frequency use, and the manufacturer identifies stable operation for inverting closed-loop gains of 10 or greater. The verified source data also lists 8 µA input bias current and 40 mA output current per channel, making the device suitable for analog signal conditioning, pulse processing, communications, and general-purpose amplification. The LM359M/NOPB ordering suffix identifies a specific Texas Instruments package and delivery configuration. The verified distributor data identifies the device as a dual general-purpose amplifier in a 14-SOIC case, while the target MPN is supplied in tube packaging. The NOPB designation is retained exactly as requested; package, temperature, and qualification details not explicitly present in the supplied data are marked as needed rather than inferred. Typical applications include high-frequency analog signal conditioning, communications interfaces, waveform shaping, pulse amplification, active filtering, and industrial or consumer control systems. Designers should preserve the recommended feedback and gain configuration, provide adequate bypassing, and verify stability experimentally because the current-mode Norton architecture and its programmable characteristics are not interchangeable with ordinary voltage-mode amplifier layouts without validation. For a new design, first confirm the required gain, bandwidth, output loading, supply arrangement, and package footprint against the manufacturer datasheet. Keep high-speed feedback traces short, place compensation and bypass components close to the relevant pins, and compare measured gain, phase margin, output swing, and slew behavior in the final board environment. This page synthesizes the verified manufacturer and distributor information with practical design guidance rather than claiming an unpublished full electrical table. Because the supplied web results do not include complete verified pin assignments, electrical limits, compliance declarations, or a reliable set of pin-compatible substitutes, those fields remain explicitly identified as data-needed. The most defensible purchasing and replacement decision requires checking the current Texas Instruments datasheet and distributor cross-reference results before production release.

RFQ Contact
LM359MX - Dual 60V/us High-Speed Amplifier | Texas Instruments
LM359MX

LM359MX - Dual 60V/us High-Speed Amplifier | Texas Instruments

The Texas Instruments LM359MX is a dual, high-speed, programmable current-mode Norton amplifier with a 60 V/us slew rate, supplied in a 14-SOIC package. Each channel provides independent input-offset balancing, gain programming, frequency compensation, and output saturation control. The verified listing identifies two general-purpose amplifier circuits in one package, making LM359MX suitable for analog signal conditioning, waveform shaping, and programmable-gain systems. A current-mode amplifier, commonly called a Norton amplifier, senses input current rather than directly measuring input voltage. LM359MX uses that architecture to achieve high bandwidth and fast slew performance while allowing gain and compensation to be programmed with external components. Each amplifier can therefore adapt its dynamic behavior to a particular signal bandwidth, gain, or output-drive requirement rather than operating only with fixed internal settings. The two independent channels support simultaneous analog processing or separate signal paths. Programmable operating characteristics are useful when one circuit must amplify small instrumentation signals and another must process faster pulses. The 60 V/us slew rate helps preserve large-signal waveform fidelity, while the dual configuration can reduce component count where two compatible amplifier functions are needed. Typical uses include pulse and transient amplifiers, analog summing stages, video or communications interface signal conditioning, laboratory interfaces, and wideband control loops. Because operating characteristics are programmable, the external network around each channel is as important as the nominal device specifications. Feedback components, compensation values, source impedance, and output loading must be selected together to maintain intended bandwidth and stability. For PCB layout, use a grounded return path near each amplifier, keep sensitive input and feedback traces short, and place compensation components close to their associated pins. The tape-and-reel ordering suffix MX identifies the verified LM359MX package configuration, while the functional LM359 family documentation describes the shared dual current-differencing architecture and programmable operating behavior. This page combines the verified manufacturer and distributor listing data with engineering guidance for the LM359MX. It also makes missing electrical limits and availability values explicit rather than inferring them, allowing designers to evaluate the device against the full LM359 datasheet and current authorized-distributor inventory before releasing a design.

RFQ Contact
LM359MX/NOPB - Dual 400MHz Norton Amplifier | Texas Instruments
LM359MX/NOPB

LM359MX/NOPB - Dual 400MHz Norton Amplifier | Texas Instruments

Texas Instruments LM359MX/NOPB is a dual, high-speed, programmable current-mode Norton amplifier IC with 400 MHz gain-bandwidth product, 60 V/µs slew rate, and two amplifier circuits in a 14-pin SOIC (D) package. According to the manufacturer product page and the LM359 data sheet, the device operates from a 5 V to 22 V supply, supports an operating temperature range of 0 °C to 70 °C for this ordering variant, and is intended for high-frequency signal conditioning, video, communications, and pulse applications. The LM359 uses current-differencing input stages rather than conventional voltage-input op-amp inputs, allowing the user to program amplifier operating characteristics with external components. Each amplifier is broadbanded for high gain-bandwidth product and fast slew rate, while stable operation is emphasized for inverting closed-loop gains of 10 or more. The two independent channels make the part suitable for dual-ended signal paths, differential interfaces, gain blocks, and active filtering. LM359MX/NOPB is supplied in tape-and-reel packaging with the manufacturer suffix MX. The component is a general-purpose precision analog building block rather than a digital or power-management device. Its 14-pin SOIC package supports conventional surface-mount assembly, but high-frequency layouts should minimize parasitic capacitance, provide adequate ground-plane continuity, and keep feedback components close to the relevant amplifier pins. Because the LM359 is a Norton-style amplifier, input bias current, input offset current, and feedback-network design materially affect accuracy. Engineers should use the manufacturer data sheet for the complete pinout, common-mode limits, output swing, input-current equations, and recommended application circuits.

RFQ Contact
LM359N/NOPB - Dual 400MHz Norton Op-Amp, 14-DIP | Texas Instruments
LM359N/NOPB

LM359N/NOPB - Dual 400MHz Norton Op-Amp, 14-DIP | Texas Instruments

The Texas Instruments LM359N/NOPB is a dual, high-speed, programmable, current-mode (Norton) amplifier integrated circuit housed in a 14-pin PDIP through-hole package. Each of the two independent amplifiers delivers a 400 MHz gain bandwidth product and a 60 V/µs slew rate, while providing user-programmable operating current and bandwidth through external resistors. The device operates from standard ±5V to ±15V (or single-supply 10V to 30V) supplies and is specified across the commercial 0 °C to +70 °C temperature range, making it suitable for cost-sensitive broadband and high-frequency signal-conditioning applications. A Norton (current-differencing) amplifier is a class of operational amplifier whose inverting input senses current rather than voltage, derived from classic current-differencing telemetry circuits. In the broader signal-chain hierarchy, Norton amplifiers belong to the linear IC family, sit alongside conventional voltage-feedback op-amps, and are commonly used as front-end gain blocks, video buffers, oscillators, comparators, and high-frequency AC amplifiers where standard op-amps lack sufficient speed. The LM359N/NOPB's two independent channels let one IC implement a complete two-stage function such as cascaded video gain or quadrature oscillator channels. Key features include a 400 MHz gain-bandwidth product, 60 V/µs slew rate, two independent Norton input stages, externally programmable quiescent current and bandwidth, and stable operation at closed-loop inverting gains of 10 or greater. Each amplifier can be biased to trade bandwidth against supply current, allowing designers to optimize power consumption for the target signal frequency. The 14-PDIP through-hole footprint simplifies prototyping, breadboarding, and legacy repair work on industrial control cards. The LM359 architecture pairs a current differencing input with a high-gain voltage output stage, yielding good high-frequency response that approaches that of much more expensive RF amplifiers. Because each amplifier's operating current is set by a single external resistor, the same device can serve as a 400 MHz wideband buffer or be reconfigured as a lower-power 50 MHz block by simply increasing the programming resistor. This flexibility is a key reason the part remains popular in instrumentation, video, RF, and oscillator designs decades after introduction. Typical applications include video and pulse amplifiers, RF and IF signal conditioning, wideband oscillators, current-mode comparators, and high-speed integrators. The two-amplifier configuration also suits active filter designs and instrumentation front ends that need matched channels. Designers retrofitting older equipment will find the DIP package convenient when working with through-hole production lines and replacement sockets. When designing with the LM359N/NOPB, program each amplifier's bandwidth and supply current through the I_set pin to balance power dissipation against required slew rate. A small ceramic bypass capacitor close to the supply pins is recommended to maintain high-frequency PSRR, and PCB traces to the inverting input should be kept short to minimize stray capacitance that could destabilize the high-gain stages.

RFQ Contact