Products (44,000+)

MAX3232IDWRG4 - Dual RS-232 Transceiver | Texas Instruments
MAX3232IDWRG4

MAX3232IDWRG4 - Dual RS-232 Transceiver | Texas Instruments

Texas Instruments MAX3232IDWRG4 is a dual-channel RS-232 line driver and receiver operating from a 3 V to 5.5 V supply, with a maximum data rate of 250 kbps and ±15 kV ESD protection on each I/O pin. The device is packaged in a 16-pin SOIC (DW) package and is specified for an industrial temperature range of -40°C to +85°C. An RS-232 transceiver is an interface IC that converts low-voltage logic signals into RS-232 line levels and receives differential bipolar signals, converting them back into CMOS-compatible logic levels. This dual-driver, dual-receiver arrangement places the MAX3232IDWRG4 within the hierarchy of interface ICs, serial transceivers, line drivers and receivers, and data-conversion semiconductors. It is used where a powered system must exchange data with an RS-232 equipment port. The principal features include two transmit channels, two receive channels, operation from a single 3 V to 5.5 V supply, data rates up to 250 kbps, and ±15 kV ESD protection. The industrial-temperature rating supports equipment operating across extended ambient conditions. These characteristics make the device suitable for industrial controls, test equipment, POS terminals, and embedded systems that communicate with legacy RS-232 peripherals. The MAX3232 interface architecture uses on-chip level-shifting circuitry to produce the positive and negative voltage swings required by RS-232 while operating from a modern low-voltage supply. Because RS-232 is a point-to-point interface, each transmitter should drive one receiver and the connection should include signal-ground continuity. The 250 kbps capability supports legacy control and diagnostic protocols without requiring a separate line-driver IC. Typical applications include industrial serial controllers, laboratory test systems, point-of-sale equipment, barcode scanners, and service-console interfaces. In each case, the IC handles the physical RS-232 voltage conversion while the host UART handles framing, parity, and data-rate configuration. The device can therefore simplify board partitioning by combining the driver and receiver functions in one package. PCB implementation should preserve the required charge-pump capacitors, route each RS-232 line away from sensitive analog signals, and provide a low-impedance ground path between the two connected systems. Confirm the external capacitor values, pin assignments, and maximum driver-load requirements against the manufacturer datasheet before releasing a new layout. The device is a digital interface IC, so a safe operating area curve is not applicable. This product record combines the manufacturer’s electrical and package specifications, sourcing guidance, practical layout considerations, and same-footprint replacement information. It is intended to help engineers evaluate the MAX3232IDWRG4 for new designs, cross-reference legacy RS-232 interfaces, and plan industrial-temperature production boards.

RFQ Contact
MAX3232IPW - 250kbps Dual RS-232 Transceiver | Texas Instruments
MAX3232IPW

MAX3232IPW - 250kbps Dual RS-232 Transceiver | Texas Instruments

Texas Instruments MAX3232IPW is a dual-channel RS-232 line driver and receiver operating from 3V to 5.5V, supporting data rates up to 250kbit/s and providing ±15kV ESD protection. The device is packaged in a 16-pin TSSOP package. It combines two RS-232 drivers, two RS-232 receivers, and onboard charge-pump circuitry that produces the bipolar voltage levels required by the RS-232 interface. An RS-232 transceiver is an interface IC that bridges a low-voltage digital logic system and a serial communications link using single-ended, bipolar signaling. The MAX3232 belongs to the RS-232 interface transceiver hierarchy, where line drivers convert logic signals into RS-232 levels and receivers convert transmitted levels back into CMOS-compatible logic. Its onboard charge pumps allow operation from a single 3V to 5.5V supply rather than requiring a separate ±12V supply. The MAX3232 provides two transmit channels and two receive channels, making it appropriate for implementing a compact RS-232 port. Its maximum 250kbit/s data rate supports conventional serial-port communication while exceeding the throughput needed by many control, instrumentation, and industrial interfaces. The integrated protection is specified to ±15kV on the serial-port connection terminals, including ground, improving robustness when cables are exposed to electrostatic discharge. Internally, the charge-pump circuits generate the positive and negative voltages required by the drivers, while the receiver section provides RS-232 thresholding and noise-tolerant logic-level output. According to the manufacturer datasheet, the device meets or exceeds the requirements of TIA/EIA-232-F and ITU V.28. It also accepts 5V logic, allowing the interface to operate alongside conventional 5V digital systems. Typical applications include industrial control links, test and measurement equipment, POS terminals, security systems, and embedded serial-port designs. The dual-channel arrangement can support one full-duplex RS-232 connection or two unidirectional links, depending on how the driver and receiver pins are assigned. The 16-pin TSSOP package also supports compact surface-mount PCB layouts. When laying out the circuit, place the required external charge-pump capacitors close to their designated pins and route the RS-232 connector-side traces away from sensitive logic. Confirm that the selected external capacitors meet the device's voltage and tolerance requirements. Also verify the electrical requirements of the connected equipment before substituting a similarly packaged transceiver. This page consolidates the verified manufacturer and distributor information with practical interface-layout guidance, pin-compatible alternatives, and a parameter comparison. It is intended to accelerate component selection while keeping all unverified electrical details explicitly identified rather than inferred.

RFQ Contact
MAX3232IPWG4 - RS-232 Transceiver | Texas Instruments
MAX3232IPWG4

MAX3232IPWG4 - RS-232 Transceiver | Texas Instruments

Texas Instruments MAX3232IPWG4 is a multichannel RS-232 line driver and receiver IC with 3 V to 5.5 V single-supply operation, integrated charge-pump voltage conversion, and ±15 kV ESD protection. The device provides two transmit channels and two receive channels in a 16-pin TSSOP package, making it suitable for industrial serial interfaces, data acquisition equipment, and embedded control systems. Its receiver includes enhanced ESD protection and fail-safe operation, while the transmitters support RS-232 signal levels from a low-voltage digital supply. An RS-232 transceiver combines a line driver, line receiver, and level-shifting charge-pump circuit in one package. The driver converts low-voltage logic signals into RS-232-compatible levels, while the receiver converts bipolar RS-232 signals back into CMOS-compatible logic. This integration reduces external circuitry, simplifies system design, and is especially useful when the host interface operates at 3.3 V or 5 V but the connected equipment requires RS-232 voltage levels. The MAX3232IPWG4 operates across a 3 V to 5.5 V supply range, allowing use with both 3.3 V and 5 V systems. Its multichannel architecture supports two RS-232 transmit and two receive functions in one 16-terminal TSSOP package. The integrated charge pump generates the positive and negative voltage levels required by RS-232 without a separate negative supply, and the integrated protection circuitry helps improve robustness when ports are exposed to electrostatic discharge. The part is specified for an industrial operating temperature range of -40 °C to +85 °C and uses a 0.65 mm terminal pitch. Its 16-pin TSSOP construction supports compact PCB layouts while preserving enough pin density for two full-duplex RS-232 channels. The MAX3232IPWG4 is also associated with a ±15 kV ESD-protection feature in the device family documentation, making it a practical choice for equipment interfaces exposed to cable transients. Typical applications include serial adapters, industrial controllers, test equipment, point-of-sale terminals, embedded instrumentation, and communication links between a low-voltage processor and an RS-232 peripheral. Designers should provide the external charge-pump capacitors and, where required, the recommended driver and receiver bypass capacitors at the pins specified by the manufacturer datasheet. Keep the RS-232 traces short, route them away from sensitive clock and analog signals, and connect the protection ground arrangement as recommended for the application. The MAX3232 family also includes an improved MAX3232E replacement recommended by Texas Instruments for new designs. Engineers evaluating alternatives should compare supply range, channel count, ESD rating, logic levels, package, and capacitor requirements before approving a substitution. This page combines device specifications, replacement guidance, package information, and practical interface-design considerations for faster engineering selection.

RFQ Contact
MAX3232IPWR - 250kbps Dual RS-232 Transceiver | Texas Instruments (Tape & Reel)
MAX3232IPWR

MAX3232IPWR - 250kbps Dual RS-232 Transceiver | Texas Instruments (Tape & Reel)

Texas Instruments MAX3232IPWR is a dual-channel RS-232 line driver and receiver operating from 3V to 5.5V, supporting data rates up to 250kbit/s and providing ±15kV ESD protection. The device is packaged in a 16-pin TSSOP package. It combines two RS-232 drivers, two RS-232 receivers, and onboard charge-pump circuitry that produces the bipolar voltage levels required by the RS-232 interface. An RS-232 transceiver is an interface IC that bridges a low-voltage digital logic system and a serial communications link using single-ended, bipolar signaling. The MAX3232 belongs to the RS-232 interface transceiver hierarchy, where line drivers convert logic signals into RS-232 levels and receivers convert transmitted levels back into CMOS-compatible logic. Its onboard charge pumps allow operation from a single 3V to 5.5V supply rather than requiring a separate ±12V supply. The MAX3232 provides two transmit channels and two receive channels, making it appropriate for implementing a compact RS-232 port. Its maximum 250kbit/s data rate supports conventional serial-port communication while exceeding the throughput needed by many control, instrumentation, and industrial interfaces. The integrated protection is specified to ±15kV on the serial-port connection terminals, including ground, improving robustness when cables are exposed to electrostatic discharge. Internally, the charge-pump circuits generate the positive and negative voltages required by the drivers, while the receiver section provides RS-232 thresholding and noise-tolerant logic-level output. According to the manufacturer datasheet, the device meets or exceeds the requirements of TIA/EIA-232-F and ITU V.28. It also accepts 5V logic, allowing the interface to operate alongside conventional 5V digital systems. Typical applications include industrial control links, test and measurement equipment, POS terminals, security systems, and embedded serial-port designs. The dual-channel arrangement can support one full-duplex RS-232 connection or two unidirectional links, depending on how the driver and receiver pins are assigned. The 16-pin TSSOP package also supports compact surface-mount PCB layouts. When laying out the circuit, place the required external charge-pump capacitors close to their designated pins and route the RS-232 connector-side traces away from sensitive logic. Confirm that the selected external capacitors meet the device's voltage and tolerance requirements. Also verify the electrical requirements of the connected equipment before substituting a similarly packaged transceiver. This page consolidates the verified manufacturer and distributor information with practical interface-layout guidance, pin-compatible alternatives, and a parameter comparison. It is intended to accelerate component selection while keeping all unverified electrical details explicitly identified rather than inferred.

RFQ Contact
MAX3232IPWRE4 - Dual RS-232 Transceiver | Texas Instruments
MAX3232IPWRE4

MAX3232IPWRE4 - Dual RS-232 Transceiver | Texas Instruments

Texas Instruments MAX3232IPWRE4 is a dual-channel RS-232 line-driver and line-receiver transceiver operating from a 3 V to 5.5 V supply, supporting data rates up to 250 kbit/s in a 16-pin TSSOP package. The device integrates two drivers, two receivers, a dual charge-pump circuit, and pin-to-pin ±15 kV ESD protection on the serial-port connection pins. An RS-232 transceiver is an interface IC that bridges a low-voltage digital logic system and the voltage levels used by RS-232 serial equipment. The MAX3232 combines bipolar line-driver outputs, receiver inputs, and charge-pump-assisted level shifting in one package. This integration allows a modern microcontroller or processor with TTL or CMOS-compatible logic to communicate with legacy RS-232 peripherals over a multi-drop or point-to-point serial link. Principal features include two transmit channels, two receive channels, operation from a 3 V to 5.5 V VCC supply, and a maximum data rate of 250 kbit/s. The MAX3232 accepts 5 V logic, requires external 0.1 µF charge-pump capacitors, and has a typical low supply current of 300 µA. The industrial-temperature ordering option supports operation from −40 °C to 85 °C while maintaining a surface-mount footprint suitable for compact embedded equipment. The integrated dual charge pump generates the positive and negative voltage levels needed by RS-232 transmitters. Although the interface-side supply is only 3 V to 5.5 V, the driver outputs use the charge-pump voltage rails to provide RS-232-compatible signaling. The receiver section converts the bipolar RS-232 input levels into logic-compatible signals, allowing the same device to support complete host-to-peripheral serial links when both driver and receiver channels are used. Typical applications include industrial serial-port controllers, point-of-sale terminals, test and measurement equipment, data-acquisition systems, and embedded control boards that require an RS-232 connection. The 250 kbit/s capability is suitable for legacy serial protocols, while the integrated ±15 kV ESD protection helps improve robustness when cables connect the board to external equipment. The charge-pump capacitors must be placed close to their associated pins, and the logic and serial interfaces should be routed to reduce noise coupling. Check the device’s supply, logic-level, temperature, and ESD requirements before production release, especially when replacing an RS-232 component with different channel counts or a different package. This product page consolidates the MAX3232IPWRE4 interface specifications, package information, practical RS-232 design guidance, and verified replacement considerations. It is intended to help engineers evaluate the part quickly while preserving the distinction between electrical compatibility, package compatibility, and application-specific design requirements.

RFQ Contact
MAX3232IPWRG4 - 3-5.5V RS-232 Transceiver | Texas Instruments
MAX3232IPWRG4

MAX3232IPWRG4 - 3-5.5V RS-232 Transceiver | Texas Instruments

The Texas Instruments MAX3232IPWRG4 is a 3 V to 5.5 V dual RS-232 line driver and receiver with a 16-pin TSSOP package, two transmit channels, two receive channels, and ±15-kV ESD protection on the serial-port terminals. It is designed to connect an asynchronous communication controller to an RS-232 connector while operating from a single low-voltage supply. An RS-232 transceiver is a semiconductor interface that converts logic-level signals into RS-232 line levels and converts received line-level signals back into CMOS logic. The MAX3232 belongs to the interface IC and RS-232 transceiver hierarchy, using an on-chip dual charge-pump circuit to generate the positive and negative voltages required by true RS-232 operation. This makes it suitable for industrial control, instrumentation, point-of-sale equipment, and legacy serial-port systems. Key features include a 3 V to 5.5 V supply range, full-duplex operation with two drivers and two receivers, and data rates up to 250 kbps according to the manufacturer product information. The device also provides ±15-kV ESD protection on the serial-port connection terminals and uses external 0.1 µF charge-pump capacitors. Its low-voltage operation reduces the power burden compared with traditional ±5 V or ±12 V RS-232 implementations. The internal charge-pump circuitry generates the bipolar voltages required to meet TIA/EIA-232-F electrical requirements. Because the charge pump switches internally, PCB layout must keep the charge-pump capacitors close to their designated pins and preserve adequate routing away from sensitive analog or communication circuits. The receiver includes hysteresis, which helps reject noise and prevents excessive output chatter as an input signal crosses the logic threshold. Typical applications include legacy RS-232 ports on industrial controllers, test and measurement equipment, programmable logic controllers, security systems, and computer peripherals. The part is particularly useful where a modern 3.3 V or 5 V controller must communicate with an RS-232 device through a DB9 or equivalent connector. The principal design trade-off is that the MAX3232IPWRG4 is a mature RS-232 interface rather than a modern USB-to-serial bridge. It requires external charge-pump capacitors, a suitable connector, and careful treatment of the exposed cable-side pins. Its industrial temperature grade supports equipment intended for a wider operating environment than commercial-temperature parts. This product record combines manufacturer specifications, exact package information, lifecycle status, source links, and verified substitute information to support component selection. Engineers can use the comparison table and replacement notes to determine whether an alternative preserves the TSSOP-16 footprint, supply range, channel count, and RS-232 operating characteristics.

RFQ Contact
MAX3232MDBREP - 2/2 RS-232 Transceiver, 16-SSOP, +/-15kV ESD | TI
MAX3232MDBREP

MAX3232MDBREP - 2/2 RS-232 Transceiver, 16-SSOP, +/-15kV ESD | TI

The Texas Instruments MAX3232MDBREP is a dual RS-232 line driver and dual line receiver transceiver with on-chip charge-pump voltage conversion, operating from a 3 V to 5.5 V single supply and packaged in a 16-pin SSOP (DB) package. It delivers data rates up to 250 kbps and provides +/-15 kV human-body-model ESD protection on all bus pins, including ground. An RS-232 transceiver is a type of interface IC that converts logic-level TTL/CMOS signals into RS-232 bipolar levels and back again. In the signal-chain hierarchy, an RS-232 transceiver sits between an asynchronous communication controller (UART) and a physical serial-port connector, and it forms the electrical interface layer of the RS-232 standard (TIA/EIA-232-F and ITU V.28). The MAX3232 implements this function with integrated charge pumps, so no external RS-232 line-power supply is needed. Key features of the MAX3232MDBREP include a 3 V to 5.5 V operating range, 250 kbps maximum data rate, 2 drivers and 2 receivers per package, and pin-to-pin ESD protection of +/-15 kV using the human-body model. It needs only four small external 0.1 uF charge-pump capacitors, and the SSOP (DB) package with a 5.30 mm body width saves board area over the classic SO-16 alternative. Internally, the device uses a dual charge-pump topology that generates the positive and negative voltages required to swing an RS-232 signal beyond the logic rails. The enhanced (-EP) MAX3232 variant is the part that TI recommends for new designs where margin against ±15 kV ESD events is required, while the classic MAX3232 remains functionally compatible. Typical applications include RS-232 ports on industrial control equipment, POS terminals, barcode scanners, serial-to-Ethernet gateways, security access readers, and legacy PC serial-port adapters, as well as level translation between 3.3 V UARTs and ±6 V RS-232 lines. When laying out the board, place the four 0.1 uF charge-pump capacitors on the C1+, C1-, C2+, and C2- pins close to the pins, keep the bus traces away from the charge-pump nodes to avoid coupling noise into the RS-232 signal, and reserve a chassis or signal-ground connection path for surge current return. This page consolidates parametric specifications, package and pin details, drop-in replacement options, and practical layout guidance into a single engineering reference, adding design context that the manufacturer datasheet does not cover in narrative form.

RFQ Contact
MAX3232MPWREP - 3V-5.5V Dual RS-232 Transceiver | Texas Instruments
MAX3232MPWREP

MAX3232MPWREP - 3V-5.5V Dual RS-232 Transceiver | Texas Instruments

Texas Instruments MAX3232MPWREP is a dual-channel RS-232 line transceiver with two drivers, two receivers, a dual charge-pump circuit, and ±15 kV ESD protection in a 16-pin TSSOP package. It operates from 3 V to 5.5 V and supports data rates up to 250 kbps according to the manufacturer product page. An RS-232 transceiver is the interface between a host controller and a serial-port connector. It combines transmit and receive functions on one device, translates digital logic levels to RS-232 signal levels, and includes the charge-pump circuitry required to generate the bipolar voltage used by a driver. The MAX3232 therefore belongs to the RS-232 transceiver, interface IC, communication IC, and semiconductor hierarchy. The principal features include a 3 V to 5.5 V supply range, 250 kbps operation, two line drivers, two line receivers, and pin-to-pin ±15 kV ESD protection on the serial-port connection pins, including ground. The enhanced-product ordering code identifies this variant as a high-reliability-enhanced product, making it suitable for applications that require more stringent environmental resilience than the standard commercial MAX3232 offering. The device implements two independent communication paths in one package. A host UART can transmit through either driver and receive data through either receiver, while the integrated charge pumps support RS-232 voltage levels from a single low-voltage supply. Although the analog interface tolerates the RS-232 signaling environment, the digital logic side remains compatible with ordinary CMOS-style host logic. Typical uses include industrial serial adapters, point-of-sale equipment, data-acquisition systems, industrial controls, and embedded instrumentation. The dual-channel arrangement is especially useful when a system needs both transmit and receive paths in a compact area and cannot justify separate unidirectional driver and receiver devices. Circuit design should follow the manufacturer's pin description table when assigning supply, charge-pump, driver, receiver, and ground connections. Keep external charge-pump capacitors close to their associated pins, provide the required supply decoupling, and route exposed connector-side nets away from sensitive logic where practical. Confirm the exact pin functions and thermal limits in the manufacturer datasheet before layout signoff. This page combines the device's RS-232 architecture, interface parameters, application guidance, verified-source links, and drop-in replacement analysis into a design-focused reference. It highlights package compatibility, external capacitor requirements, ESD considerations, and the differences between the enhanced and standard MAX3232 families for faster engineering selection.

RFQ Contact
MAX3238EAI+ - 3-5.5V RS-232 Transceiver with AutoShutdown Plus | ADI
MAX3238EAI+

MAX3238EAI+ - 3-5.5V RS-232 Transceiver with AutoShutdown Plus | ADI

The Analog Devices (formerly Maxim Integrated) MAX3238EAI+ is a true RS-232 transceiver operating from a single +3.0V to +5.5V supply in a 28-pin SSOP package. Per the Analog Devices datasheet, the device integrates 5 drivers and 3 receivers, supports data rates up to 250 kbps, and features the proprietary AutoShutdown Plus mode that drops supply current to 1 uA when the connected RS-232 cable is not in use. The internal dual charge-pump with four small 0.1 uF external capacitors generates the +/-5.5V RS-232 signal levels directly from a 3.3V or 5V logic supply, eliminating the need for a separate +-12V rail. An RS-232 transceiver is a line driver/receiver IC that translates logic-level UART signals (0V/3.3V or 0V/5V) into the +-5V to +-15V swing defined by the EIA/TIA-232 standard, providing the voltage translation and noise immunity required to communicate with PCs, modems, and legacy industrial equipment over cables up to 15 meters. The MAX3238EAI+ belongs to the multi-channel RS-232 transceiver category (part of the larger UART-to-RS232 interface transceiver hierarchy) within the wired communication IC market. Key features include 1 uA AutoShutdown Plus supply current, 250 kbps guaranteed data rate, integrated charge-pump requiring only four 0.1 uF capacitors, and compatibility with EIA/TIA-232 and V.28/V.24 standards. The IC also provides INVALID logic output to signal when receivers are out of range, plus FORCEON and FORCEOFF pins for manual shutdown control. The MAX3238EAI+ is the non-ESD version; the MAX3238E variant adds +/-15 kV IEC 61000-4-2 air-gap ESD protection on transceiver pins. The architecture pairs a switched-capacitor DC-DC converter (charge pump) that doubles and inverts the supply, with five RS-232 drivers and three RS-232 receivers. Compared with the older MAX232 family, the MAX3238EAI+ adds the AutoShutdown Plus feature, reducing quiescent current from typical 1 mA to 1 uA when no valid RS-232 signal is present - critical for battery-powered portable equipment. Typical applications include notebook and sub-notebook computers, PDAs, hand-held terminals, battery-powered point-of-sale equipment, and any portable system that needs an EIA/TIA-232 serial port running directly from a 3.3V or 5V battery. When designing with this part, place the four charge-pump capacitors as close to the IC as possible, use 0.1 uF ceramic with X7R or better dielectric, and tie unused driver inputs to GND through 100 kohm resistors to prevent supply-current oscillation. This page synthesizes distributor pricing, validated drop-in alternatives (MAX3238E family variants and TI MAX3238E), and practical design notes that complement the manufacturer datasheet.

RFQ Contact
MAX323EPA+ - Dual SPST Analog Switch | Analog Devices | 8-DIP
MAX323EPA+

MAX323EPA+ - Dual SPST Analog Switch | Analog Devices | 8-DIP

The Analog Devices MAX323EPA+ is a precision, single-supply, dual SPST analog switch in an 8-pin DIP package. It provides two normally open switches, operates from +2.7V to +16V, and is designed for low-power signal-routing applications where a compact, low-leakage switch is required. The device is identified as an industrial-temperature component and is supplied in a through-hole DIP package for conventional PCB assembly and prototyping. An analog switch is a semiconductor device that connects or disconnects an electrical signal path under digital control. The MAX323EPA+ belongs to the analog-switch family within the broader interface-IC and semiconductor hierarchy. Its two SPST channels provide independent normally open paths, allowing analog signals to be routed, isolated, or sampled without changing the signal level. The single-supply operation also simplifies designs compared with dual-rail switch families. Key features include two normally open switches, a +2.7V to +16V operating supply range, low power consumption of approximately 5 microwatts, and low on-resistance stated in the manufacturer product information. The MAX323 family is intended for battery-powered equipment, instrumentation, test systems, and general-purpose signal routing. The MAX323EPA+ uses an 8-pin DIP package with a rectangular body and through-hole mounting, making it suitable for industrial control boards, educational platforms, and legacy equipment. The dual SPST architecture means that each switch has one common terminal and one normally open terminal. Control inputs determine whether the corresponding signal path is connected. Because the device is precision-oriented, it is appropriate for low-voltage control and measurement systems where switch behavior, supply range, and low power consumption matter. The manufacturer describes the MAX323, MAX324, and MAX325 as related precision switch families, with the MAX323 providing two normally open switches. The MAX323EPA+ is suitable for battery-operated instruments, sensor interfaces, analog test equipment, industrial measurement systems, and sample-and-hold or signal-isolation circuits. Designers should keep the input and output signal amplitudes within the device's specified common-mode and voltage limits, provide adequate supply decoupling, and account for the nonzero off-state leakage and on-resistance when calculating accuracy. For PCB layout, place the device close to the switched signal paths and route the control traces away from sensitive analog inputs. Confirm the 8-DIP footprint, verify the pin orientation, and check the electrical limits for the specific supply and signal conditions before releasing production artwork. This page combines the manufacturer product description, distributor package information, application guidance, and drop-in replacement analysis for faster engineering decisions.

RFQ Contact
MAX323ESA+ - Dual 16V SPST Analog Switch | Maxim
MAX323ESA+

MAX323ESA+ - Dual 16V SPST Analog Switch | Maxim

The Maxim Integrated MAX323ESA+ is a precision, dual-channel, normally open SPST analog switch designed for single-supply operation from 2.7 V to 16 V. Each independent channel has a typical on-resistance of 175 ohms, and the device is housed in an 8-pin NSOIC package. Its low 5 microwatt power consumption makes it suitable for battery-powered and low-leakage signal-routing systems. An analog switch is a semiconductor device that routes electrical signals between terminals under digital control. The MAX323ESA+ belongs to the analog-switch hierarchy, where its two normally open SPST channels provide independent, unidirectional or bidirectional signal connections. In system terms, it sits between external analog circuitry and a controller, allowing a compact processor to select among sensors, test points, or signal paths. The MAX323 family provides two precision SPST switches in a single package. Both channels are normally open, meaning each path is disconnected until its control input commands closure. Operation from 2.7 V to 16 V covers 3.3 V and 5 V control systems as well as higher single-supply rails. The 5 microwatt low-power characteristic is particularly useful when leakage or standby consumption is more important than minimizing on-resistance. The device's precision switching architecture is intended for moderate-impedance signal paths rather than power switching. A 175-ohm on-resistance can limit voltage drops when carrying source currents, but it is substantially higher than a power MOSFET or relay. Engineers should therefore account for the resistance in the complete signal path and avoid using the switch as a general-purpose high-current load driver. The low-power design also makes the device appropriate for battery-powered measurement and communication equipment. Typical uses include analog test-point selection, sensor disconnect, sample-and-hold isolation, battery-powered instrumentation, and routing signals between a data-acquisition circuit and an analog front end. The MAX323 family is also identified for DAC and ADC applications, audio and video switching, communication systems, guidance and control systems, and heads-up displays where low standby power is valuable. The principal design consideration is control compatibility and signal integrity. Keep analog traces short, use a continuous ground reference, and ensure that control transitions do not inject unacceptable disturbance into sensitive measured signals. The normally open architecture also means the switch remains disconnected during power-down, which can be advantageous for isolation but may differ from a normally closed design. This page combines the manufacturer's family specifications, verified package and pricing references, application guidance, and drop-in comparison information to support component selection, PCB planning, and replacement analysis beyond the basic datasheet feature list.

RFQ Contact
MAX3241CAI+ - 3V-5.5V RS-232 Transceiver, 1Mbps | Analog Devices
MAX3241CAI+

MAX3241CAI+ - 3V-5.5V RS-232 Transceiver, 1Mbps | Analog Devices

The Analog Devices MAX3241CAI+ is a 3.0V to 5.5V low-power true RS-232 transceiver supporting data rates up to 1Mbps, packaged in a 28-pin SSOP (5.30 mm body width). The device integrates three line drivers and five line receivers in a single IC, with a dual charge-pump architecture that requires only four external 0.1uF capacitors, eliminating the need for a bipolar ±12V supply. A RS-232 transceiver is a type of line driver/receiver interface IC that converts logic-level (TTL/CMOS) signals to/from the bipolar ±5V to ±15V voltage swings required by the EIA/TIA-232-E standard. It belongs to the broader category of serial interface ICs (RS-232, RS-422, RS-485, UART transceivers), which sit between a microcontroller UART and the physical cable in point-to-point or multipoint data links. Charge-pump transceivers like the MAX3241 family simplify system design by generating the required transmitter output voltages internally from a single low-voltage rail. Key features include a 1Mbps guaranteed data rate (250kbps in the standard mode, up to 1Mbps with low-ESR capacitors), always-active extra receiver outputs for monitoring external peripherals, ±15kV ESD protection on transmitter outputs and receiver inputs (HBM), and an automatic shutdown mode that drops supply current to 1uA while keeping one receiver active. The always-on monitoring receivers (R1 and R2 extra outputs) make this part especially useful in portable and battery-powered designs that must wake the host on cable or peripheral activity. The MAX3241 uses a low-dropout transmitter output stage that maintains true RS-232-compliant output levels (±5V minimum) even when operating from a discharged battery, together with an internal dual charge pump that generates the positive and negative supplies from a single 3.0V to 5.5V rail. Four small 0.1uF external capacitors provide the pump energy storage, reducing BOM cost and board area versus ±12V solutions. Typical applications include battery-powered point-of-sale terminals, industrial handheld instrumentation, networking equipment (routers, switches), laptop and notebook serial ports, cellular phone data cables, and any embedded system requiring a TIA/EIA-232-E compliant UART link from a single low-voltage logic supply. When designing with this device, place the four 0.1uF charge-pump capacitors as close as possible to the IC pins and use a low-ESR ceramic type to achieve the 1Mbps data rate. Add bulk decoupling (0.1uF + 1uF) on VCC near the device to suppress supply noise. Verify that downstream receivers tolerate the MAX3241's ±5V minimum output swing if your cable is unusually long. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ Contact
MAX3243CAI+G1Z - 3/5 RS-232 Transceiver | Analog Devices
MAX3243CAI+G1Z

MAX3243CAI+G1Z - 3/5 RS-232 Transceiver | Analog Devices

Analog Devices MAX3243CAI+G1Z is a 3-driver/5-receiver RS-232 interface transceiver designed for single-supply operation from 3 V to 5.5 V. It is offered in a 28-pin SSOP package and includes AutoShutdown power management, which reduces supply current to 1 uA when the receivers do not detect a valid signal level. The device also provides complementary always-active receiver channels for external monitoring and supports data rates up to 250 kbps. An RS-232 transceiver is an interface IC that converts logic-level digital signals into RS-232 voltage levels and converts incoming RS-232 signals back into logic-compatible levels. The MAX3243 belongs to the broader interface IC hierarchy, where line drivers and receivers bridge modern digital systems with older RS-232 equipment. Its multi-channel arrangement supports equipment needing more drivers or receivers than a simple two-channel RS-232 implementation. The MAX3243 family includes integrated charge-pump circuitry for level translation, allowing operation from a single low-voltage supply rather than the traditional positive and negative RS-232 supplies. Low-power operation is important in portable equipment, industrial control systems, and instrument panels where an idle RS-232 port should not consume significant power. AutoShutdown provides automatic supply reduction when valid receiver activity is absent, supporting efficient power management without requiring a dedicated GPIO control signal. The MAX3243 is suitable for industrial control equipment, test and measurement instruments, data acquisition systems, security equipment, and service interfaces. Its always-active receiver channels can monitor external RS-232 activity even while the principal receiver channels are shut down, which is useful for detecting connection or activity status. The 28-pin SSOP package also supports compact board layouts in legacy and industrial communication products. When designing around the MAX3243CAI+G1Z, verify the 3 V to 5.5 V supply range, connector protection requirements, and the voltage levels present at each interface. RS-232 is a single-ended, unbalanced standard, so cable routing and grounding can affect signal integrity. Keep connector-side transient protection close to the connector and use the pin-description table in the manufacturer datasheet when assigning PCB tracks. AutoShutdown behavior should also be checked against the system’s expected idle state and remote-device signaling. This page combines the family-level electrical characteristics, package information, sourcing context, drop-in alternatives, and practical RS-232 design guidance to support component selection and PCB implementation.

RFQ Contact
MAX3243CAI+TG1Z - 3/5 RS-232 Transceiver | Analog Devices
MAX3243CAI+TG1Z

MAX3243CAI+TG1Z - 3/5 RS-232 Transceiver | Analog Devices

Analog Devices MAX3243CAI+TG1Z is a 3-driver/5-receiver RS-232 interface transceiver with a 28-pin SSOP package. It supports true +3 V to +5.5 V operation and uses AutoShutdown to reduce supply current to 1 µA when no valid receiver signal is detected. The device combines three RS-232 drivers, five RS-232 receivers, and a complementary always-active receiver for external monitoring. These characteristics place the MAX3243 in the interface IC hierarchy: RS-232 transceiver → serial interface IC → interface IC → semiconductor. It is intended for equipment that must translate between modern digital logic levels and RS-232 signal levels. The MAX3243 family uses Maxim’s AutoShutdown technology to lower operating power when the connected RS-232 link is inactive. A valid signal on a receiver input causes the supply and drivers to become active, while the absence of a valid signal allows the low-power state to be maintained. This behavior is particularly useful in battery-operated and intermittently connected portable equipment, where an idle serial transceiver could otherwise continue to consume unnecessary power. The operating range of +3 V to +5.5 V permits integration with both 3.3 V and 5 V systems. The 3/5 channel arrangement supports three outbound RS-232 drivers and five inbound receivers, while the additional always-active receiver provides complementary monitoring information. This makes the device appropriate for console links, instrumentation, industrial control interfaces, configuration ports, and embedded systems that exchange serial commands with external equipment. Compared with a purely unidirectional line-driver or receiver, the integrated transceiver reduces the component count and simplifies bidirectional RS-232 connections. The MAX3243CAI+TG1Z ordering code identifies a 28-SSOP package offered by Analog Devices/Maxim Integrated. Its integrated interface functionality supports compact designs where board area is important. Because RS-232 uses a single-ended signaling method referenced to ground, the complete circuit also depends on the external charge-pump capacitors, pass capacitors, protection elements, connector, and cable. Those surrounding components determine practical bus-range and signal-integrity behavior in the finished equipment. A robust implementation should place the required charge-pump capacitors close to their associated pins, connect the interface ground appropriately with the system ground, and provide the protection strategy required by the installation environment. Long or exposed cables can introduce electrostatic discharge, transients, and ground-offset problems that are not solved by the transceiver alone. Application review should therefore include the cable length, operating environment, logic levels, and whether the connected system requires hardware handshaking. This product page summarizes the verified manufacturer identity, channel configuration, supply range, shutdown behavior, package, and ordering code. It also organizes functional applications, design cautions, candidate replacements, and specification comparisons so that engineers can assess fit quickly while treating the MAX3243 datasheet as the governing technical document.

RFQ Contact
MAX3243CDBG4 - 250kbps 3/5 RS-232 Transceiver | TI
MAX3243CDBG4

MAX3243CDBG4 - 250kbps 3/5 RS-232 Transceiver | TI

The Texas Instruments MAX3243CDBG4 is a 3-driver, 5-receiver RS-232 line-driver and receiver with a 250 kbps data rate, a 3 V to 5.5 V supply range, and ±15 kV HBM ESD protection. It is packaged in a 28-pin SSOP for compact serial-interface equipment. An RS-232 transceiver is an interface IC that converts logic-level digital signals into RS-232 levels and converts incoming RS-232 signals back into logic-compatible levels. The MAX3243 belongs to the RS-232 transceiver class, within interface ICs and broader semiconductor communication-interface devices. It supports asymmetric designs requiring three transmit channels and five receive channels, making it useful for multiport serial controllers, data acquisition equipment, and service interfaces. The three RS-232 drivers and five receivers operate from a single 3 V to 5.5 V supply. Its maximum signaling rate of 250 kbps supports conventional serial communication while providing useful margin for a broad range of industrial and embedded links. The ±15 kV human-body-model ESD rating is a significant handling advantage when an exposed connector places the interface close to cables, external equipment, or less controlled user-accessible ports. The MAX3243CDBG4 ordering code identifies the commercial-temperature, 28-pin SSOP configuration. The SSOP package offers a substantially smaller board footprint than a conventional 28-pin plastic DIP while remaining compatible with automated surface-mount assembly. Tube packaging is specified for this ordering option, allowing distributors and contract manufacturers to handle the components in standard production workflows. Typical applications include multichannel RS-232 test equipment, industrial controller service ports, serial adapters, instrumentation, embedded systems, and legacy peripheral interfaces. The three transmitters can drive three separate RS-232 outputs, while five receivers allow one controller to monitor five incoming signals without requiring five separate interface devices. This asymmetry can simplify system partitioning when a design has fewer outbound data paths than inbound control or status paths. Layout should keep the transceiver close to its connector and separate the protected communication interface from sensitive digital circuitry. Follow the pin-description table and recommended decoupling arrangement in the manufacturer datasheet. Check signal polarity and connector assignment for every RS-232 channel, and verify that the selected cable uses the correct DB9 or alternative connector convention rather than assuming a universal pinout. This product page combines manufacturer specifications, package information, validated drop-in alternatives, and application-focused design guidance. It is intended to accelerate component identification and board-level engineering while preserving the distinctions that matter when replacing a serial-interface IC.

RFQ Contact
MAX3243CDBRG4 - 250kbps RS-232 Transceiver | Texas Instruments
MAX3243CDBRG4

MAX3243CDBRG4 - 250kbps RS-232 Transceiver | Texas Instruments

The Texas Instruments MAX3243CDBRG4 is a 3- to 5.5-V multichannel RS-232 line driver and receiver rated for data rates up to 250 kbps, with ±15 kV ESD protection in a 28-pin SSOP package. It combines three drivers and three receivers, making it suitable for three-channel serial interfaces operating from either 3 V or 5 V supplies. An RS-232 transceiver is an interface IC that converts logic-level signals into RS-232 line levels and converts received RS-232 signals back into logic-compatible levels. Within the interface hierarchy, the MAX3243 belongs to the RS-232 transceiver family, providing bidirectional signal conditioning between a host controller and external serial equipment. Its multichannel configuration reduces the number of external interface components required for multiport designs. Key operating characteristics include a 3 V to 5.5 V supply range, a maximum data rate of 250 kbps, three driver channels, three receiver channels, and ±15 kV human-body-model ESD protection. These features make the device useful for industrial control systems, POS terminals, instrumentation, and embedded systems that connect legacy RS-232 equipment over cable lengths where transient electrical noise is likely. The MAX3243 is designed for single-ended RS-232 communication and supports both 3 V and 5 V system rails, allowing the same interface design to be used across different logic-voltage systems. Its integrated multichannel architecture simplifies board space compared with separate single-channel transceivers. ESD protection improves robustness at connector-facing pins, although designers must still use appropriate cable, grounding, and signal-integrity practices. Typical applications include industrial serial controllers, point-of-sale equipment, barcode and label printers, security systems, test equipment, and embedded data-acquisition systems. In each case, the three-channel arrangement can serve multiple serial ports while limiting the number of external line-driver and receiver assemblies. A key implementation consideration is that RS-232 uses unbalanced single-ended signaling and is not a direct substitute for differential RS-422 or RS-485. PCB routing should keep driver and receiver traces away from noisy switching nodes, while grounding and cable practices should follow the applicable RS-232 system requirements. This page combines the exact manufacturer specifications for the MAX3243CDBRG4 with package, sourcing, and engineering guidance. It also identifies same-footprint family alternatives and highlights the temperature-grade and lifecycle checks that should be completed before approving a replacement for an existing design.

RFQ Contact
MAX3243CDW - 3-5.5V 250kbps RS-232 Transceiver | Texas Instruments
MAX3243CDW

MAX3243CDW - 3-5.5V 250kbps RS-232 Transceiver | Texas Instruments

Texas Instruments MAX3243CDW is a multichannel RS-232 line driver and receiver interface IC with a 3 V to 5.5 V supply range, data rate up to 250 kbps, and ±15 kV human-body-model ESD protection on the serial interface pins. The device is packaged in a 28-pin SOIC and combines three line drivers with five line receivers for full-duplex serial-interface designs. An RS-232 transceiver is an interface integrated circuit that converts logic-level signals into balanced, single-ended RS-232 line voltages and converts received line voltages back into logic levels. The MAX3243 belongs to the multi-channel transceiver class within the broader hierarchy of interface ICs, serial communication controllers, and semiconductor signal-conditioning devices. Its integrated driver and receiver channels reduce the number of separate components required in legacy serial ports, industrial control links, and service interfaces. The three-driver and five-receiver configuration allows one connector to support several RS-232 signals without using five unrelated transceivers. Operation from 3 V to 5.5 V makes the device suitable for systems that use 3.3 V or 5 V control electronics. The specified 250 kbps data rate covers legacy serial communication while providing useful margin below faster RS-485 interfaces. The ±15 kV HBM protection rating strengthens the connector-side interface against electrostatic discharge events. Internally, the MAX3243 uses charge-pump circuitry to generate the voltage levels required by RS-232 transmitters. The three drivers add the required line signal, while the five receivers detect and condition incoming signals. The asymmetric channel count supports designs in which a system transmits on three lines and monitors five incoming lines, including handshake, status, and acknowledgment signals. Typical uses include industrial control panels, data-acquisition equipment, instrumentation, embedded service consoles, and legacy peripheral connections. It is particularly suitable where a modern controller must retain compatibility with an established RS-232 port but also needs a compact multi-channel interface. A single transceiver can consolidate several point-to-point or multidrop-compatible links when the system designer follows the RS-232 topology correctly. PCB design should keep the charge-pump and interface circuitry on the manufacturer's recommended layout and provide the required bypass capacitance close to the supply pins. Keep serial traces short, provide the intended common-mode return path, and use suitable protection networks where cables leave the enclosure. Do not infer that the HBM rating eliminates the need for external surge protection on long or unprotected cable runs. This product page consolidates the manufacturer specifications, channel configuration, source links, drop-in comparison, and implementation guidance into a design-focused reference. Engineers can use the comparison and selection guidance to evaluate the MAX3243CDW alongside pin-compatible alternatives, while the application notes clarify where its 28-pin SOIC interface fits in embedded and industrial serial systems.

RFQ Contact
MAX3243CDWR - 250kbps RS-232 Transceiver | Texas Instruments
MAX3243CDWR

MAX3243CDWR - 250kbps RS-232 Transceiver | Texas Instruments

The Texas Instruments MAX3243CDWR is a multichannel RS-232 line driver and receiver with three drivers, five receivers, a maximum data rate of 250kbps, and ±15kV HBM ESD protection. It operates from a 3V to 5.5V supply and is packaged in a 28-pin SOIC for surface-mount industrial, communications, and embedded equipment. An RS-232 transceiver is an interface IC that combines a line driver, which converts TTL or CMOS logic signals into RS-232 voltage levels, with a receiver, which converts RS-232 signals back into logic levels. This integration reduces the number of external components required for serial-port interfaces and places both signal-conversion functions in one compact package. The MAX3243CDWR supports a maximum signaling rate of 250kbps while operating across a 3V to 5.5V supply range. Its three drivers support multiple outbound serial channels, and its five receivers provide additional inbound channel capacity. The integrated ±15kV HBM ESD protection helps improve system resilience when a cable port is exposed to electrostatic discharge. The device is designed for conventional RS-232 point-to-point links found in industrial control systems, data-acquisition equipment, service interfaces, and legacy peripheral connections. Because RS-232 uses unbalanced signaling, cable routing and grounding remain important even when the IC itself provides high levels of on-chip ESD protection. The 28-pin SOIC package supports automated assembly and provides separate driver, receiver, ground, and supply connections. Applications can use the additional receiver channels for modem-control signals, hardware handshaking, status inputs, or other low-speed RS-232 signaling where the system requires more receive capability than the three driver channels. When laying out a board, place the transceiver close to the connector and route each interface line directly to its assigned pin. Keep RS-232 traces away from clocks, switching-regulator nodes, and high-speed digital edges. The signal ground reference should be connected through the cable shield or according to the equipment grounding architecture, while chassis and signal grounds should remain separated where required by the interface specification. This page combines the manufacturer specifications, explicit distributor pricing, verified drop-in references, and practical PCB guidance for engineers evaluating the MAX3243CDWR. It also distinguishes documented channel, voltage, speed, protection, and package details from information that requires separate engineering confirmation.

RFQ Contact
MAX3243CDWRG4 - 3/5 RS-232 Transceiver | Texas Instruments
MAX3243CDWRG4

MAX3243CDWRG4 - 3/5 RS-232 Transceiver | Texas Instruments

Texas Instruments MAX3243CDWRG4 is a 3-to-5.5 V multichannel RS-232 line driver and receiver with three drivers, five receivers, a maximum data rate of 250 kbps, and ±15 kV HBM ESD protection. The device is housed in a 28-pin SOIC surface-mount package and is designed for commercial-temperature operation from 0°C to 70°C. It provides a complete interface for translating between RS-232 line-level signals and CMOS/TTL logic-level signals. An RS-232 transceiver is an interface IC used to connect equipment designed around the RS-232 standard to a digital system operating with lower logic voltages. The MAX3243 family combines multiple drivers and receivers in one package, reducing the number of separate interface components required for multiport serial equipment. Its 3-to-5.5 V supply range allows operation from common 3.3 V and 5 V system rails. The three-driver and five-receiver arrangement is suitable for RS-232 connections that require more than one serial channel, including communications equipment, test systems, industrial controllers, and computer peripherals. The 250 kbps maximum signaling rate supports substantially faster data transfer than legacy serial-port equipment commonly designed for lower rates. Integrated ±15 kV human-body-model ESD protection improves system resilience when exposed connector pins encounter electrostatic discharge. MAX3243CDWRG4 is identified as a full RS-232 transceiver with three drivers and five receivers. The manufacturer classifies it as a multichannel line driver/receiver, while the listed operating range allows operation with both 3 V and 5 V supply systems. Its 28-pin SOIC format supports conventional surface-mount assembly and is appropriate for designs where a single package must handle several RS-232 signal directions. Typical uses include industrial serial-control equipment, instrumentation, data-acquisition systems, point-of-sale terminals, and embedded systems that retain an RS-232 interface. Because the device includes both drivers and receivers, it can support two fully independent RS-232 ports while also providing one additional receive channel and additional driver capacity when required by the system architecture. For PCB implementation, place the device close to its RS-232 connector and route driver and receiver outputs as short, well-controlled signal paths. Decoupling capacitors should be connected to the supply and ground pins according to the manufacturer datasheet. The external connector and cable should also provide appropriate surge and ESD protection because the chip's internal HBM rating does not replace system-level connector protection. This product record combines the manufacturer's electrical and packaging information with practical RS-232 design guidance. It also provides structured comparisons, replacement criteria, and application notes to help engineers evaluate integration, protection, channel count, and supply compatibility before assigning the MAX3243CDWRG4 to a PCB.

RFQ Contact
MAX3243CPWR - 250kbps Multichannel RS-232 | Texas Instruments
MAX3243CPWR

MAX3243CPWR - 250kbps Multichannel RS-232 | Texas Instruments

Texas Instruments MAX3243CPWR is a 3-channel driver and 5-channel receiver RS-232 transceiver operating from 3 V to 5.5 V at up to 250 kbps, with ±15 kV HBM ESD protection, in a 28-pin TSSOP (PW) package. It is designed for systems that require multiple low-voltage RS-232 interfaces without using a higher-voltage supply. An RS-232 transceiver is an interface IC that combines line drivers, line receivers, and the charge-pump circuitry needed to generate the positive and negative voltage swings required by RS-232. The MAX3243 belongs to the RS-232 transceiver family within interface ICs, combining digital communication, analog level shifting, and electrostatic-discharge protection in one device. The MAX3243CPWR integrates three RS-232 drivers and five RS-232 receivers, supports data rates up to 250 kbps, and operates from a single 3 V to 5.5 V supply. Its ±15 kV HBM ESD protection is a key feature for ports exposed to cables, connectors, or electrostatic discharge. The device is offered in the 28-pin TSSOP PW package with an operating temperature range of 0°C to 70°C. Technically, the receiver and driver architecture allows multiple RS-232 ports to share common supply and ground rails while maintaining the voltage translation required by the RS-232 standard. On-board charge-pump circuitry supports operation from a supply below the traditional ±12 V RS-232 levels, reducing the external power requirements of portable and embedded equipment. Typical uses include industrial control interfaces, point-of-sale terminals, serial adapters, data-acquisition equipment, and embedded systems that connect to legacy RS-232 peripherals. The three-driver, five-receiver arrangement is particularly useful when a controller needs several transmit paths but fewer receive paths. PCB design should account for the charge-pump capacitors and follow the manufacturer’s recommended decoupling and layout pattern. Keep the RS-232 driver outputs away from sensitive analog or high-speed digital traces, connect the ground reference correctly through the cable interface, and provide protection appropriate to the exposed connector environment. This page organizes the key electrical limits, package information, drop-in alternatives, application guidance, and design considerations for engineers evaluating MAX3243CPWR across industrial and embedded RS-232 designs.

RFQ Contact
MAX3243CPWRG4 - 250kbps RS-232 | Texas Instruments
MAX3243CPWRG4

MAX3243CPWRG4 - 250kbps RS-232 | Texas Instruments

The Texas Instruments MAX3243CPWRG4 is a 3 V to 5.5 V multichannel RS-232 line driver and receiver capable of operating at 250 kbps, with ±15 kV human-body-model ESD protection, in a 28-pin TSSOP package. The device supports three RS-232 driver channels and three receiver channels according to its distributor listing, making it suitable for bidirectional serial data links, industrial equipment, data acquisition systems, and portable instrumentation. An RS-232 interface IC converts logic-level digital signals into RS-232-compatible line levels and converts received line signals back into logic levels. The MAX3243 belongs to the interface IC hierarchy, where it bridges a host controller or processor with a physical serial port. Its multichannel architecture supports several data paths on one board while limiting the number of separate transceiver packages required. The 3 V to 5.5 V supply range accommodates both 3.3 V and 5 V system rails. The principal electrical features are a 250 kbps maximum data rate and ±15 kV ESD protection rated to the HBM model. These characteristics make the transceiver relevant to equipment where a cable-connected port must withstand electrostatic discharge events. The receiver channels handle incoming serial data, while the driver channels convert outbound logic signals into RS-232 line levels. Commercial temperature grading, a gull-wing terminal form, and a rectangular TSSOP package support conventional surface-mount assembly. The MAX3243 family is designed for systems that require multiple RS-232 channels without using a larger transceiver for only one or two links. Its low-voltage operation allows communication between modern embedded systems and legacy RS-232 equipment. Because RS-232 is a single-ended, bipolar signaling interface, correct grounding, cable routing, and protection implementation remain important when integrating the device into an industrial or externally accessible system. Typical uses include industrial control consoles, laboratory test equipment, serial adapters, data loggers, point-of-sale systems, and embedded instrumentation. In a multiport design, several receiver inputs can monitor separate device connections while the drivers support outbound command channels. The 28-pin TSSOP package also makes the part suitable for compact single-board systems where through-hole RS-232 components would consume excessive area. When laying out the PCB, place the transceiver near its connector and connector-protection components to minimize exposed high-voltage RS-232 traces. Keep logic-side routing separated from line-side routing, provide the required bypassing capacitors close to the supply pins, and observe the device's absolute-maximum ratings for the RS-232 pins. Verify external protection, grounding, and cable requirements for the completed system rather than relying on the IC's internal ESD rating alone. This product page combines the manufacturer's device information with package, pinout, purchasing, replacement, and design guidance. It also identifies the verified same-family drop-in candidates and distinguishes them from options that would require different wiring or package changes, helping engineers evaluate an RS-232 design without treating every electrically similar transceiver as a true replacement.

RFQ Contact
MAX3243CUI+ - 3-5.5V 250kbps RS-232 Transceiver | Analog Devices
MAX3243CUI+

MAX3243CUI+ - 3-5.5V 250kbps RS-232 Transceiver | Analog Devices

The Analog Devices MAX3243CUI+ is a 3/5-channel RS-232 transceiver with a 3 V to 5.5 V supply, 250 kbps signaling capability, and ±15 kV ESD protection, housed in a 28-pin TSSOP package. It combines three RS-232 drivers and five receivers with AutoShutdown, which reduces supply current to approximately 1 µA when no valid receiver signal is present. The listed 1 k-unit manufacturer price starts at $3.43 as of 2026-10-30. An RS-232 transceiver is a serial-interface semiconductor that converts logic-level signals into RS-232 line levels and converts received line levels back into digital logic. The MAX3243 belongs to the interface IC hierarchy, where it combines drivers and receivers in one package. AutoShutdown is particularly useful for battery-powered equipment because it removes the need for a separate software-controlled power path when the serial link is idle or disconnected. The principal operating features include a 3.0 V to 5.5 V supply range, operation up to 250 kbps, integrated charge-pump circuitry, and ±15 kV ESD protection on the serial interface. The device supports both 3 V and 5 V systems, allowing the same transceiver architecture to serve industrial controls, embedded equipment, and legacy RS-232 ports. Its three drivers and five receivers provide flexible channel allocation for peripheral buses, service consoles, and point-to-point links. Technically, the MAX3243 family uses an efficient on-board power supply to generate the positive and negative voltages required by RS-232 transmitters from a single supply. The verified manufacturer page identifies the MAX3243 as production, with a product datasheet at Revision 10. The MAX3243CUI+ ordering code uses the compact TSSOP-28 package, making it suitable for space-constrained industrial-control and communications boards. Typical applications include industrial serial adapters, embedded instrumentation, POS terminals, diagnostic consoles, and communications equipment requiring both transmit and receive paths. It is especially useful where automatic power reduction is valuable, such as battery-operated test instruments or systems whose RS-232 port is only active during maintenance. The 250 kbps maximum data rate supports moderate-speed command and control traffic. When laying out the circuit, preserve the recommended charge-pump capacitor connections and place bypass capacitance close to the supply pins. Keep RS-232 traces away from sensitive analog signals, provide the required protection network if exposed to user cables, and verify the receiver polarity and logic thresholds of the connected equipment. The supplied data does not include a complete pin table, so pin assignments should be confirmed against the manufacturer datasheet before layout release. This page combines the verified manufacturer specifications, distributor pricing, package information, supported drop-in candidates, comparison parameters, and practical RS-232 design guidance. It is intended to help engineers identify the correct replacement and plan power, layout, and signal-integrity requirements without relying on distributor summaries alone.

RFQ Contact
MAX3243CUI+G1Z - 3/5 RS-232 Transceiver | Analog Devices
MAX3243CUI+G1Z

MAX3243CUI+G1Z - 3/5 RS-232 Transceiver | Analog Devices

The Analog Devices MAX3243CUI+G1Z is a 3-driver, 5-receiver RS-232 transceiver with a 1 uA supply current, a true +3 V to +5.5 V supply range, and AutoShutdown operation. The device is offered in a 28-pin TSSOP package for compact industrial, embedded, and communications equipment. Its receiver architecture includes five receiver outputs, including a complementary always-active receiver for external monitoring. A multi-driver RS-232 transceiver is an interface IC that converts logic-level signals into RS-232 line levels and converts received RS-232 signals back into logic-compatible outputs. Within the signal-chain hierarchy, the MAX3243CUI+G1Z is an RS-232 transceiver, a serial-interface component, an interface IC, and ultimately a semiconductor. It is intended for systems that need multiple driver channels and more receiver channels than a conventional two-driver, two-receiver transceiver provides. The principal feature is its combination of three drivers and five receivers in one package. AutoShutdown reduces supply current to 1 uA when the receiver inputs do not detect a valid signal level, helping conserve power in systems that remain connected intermittently. Operation from +3 V to +5.5 V supports both 3.3 V and 5 V logic environments. The complementary always-active receiver provides a monitoring path for designs that require an output to remain observable when the principal receiver channels are inactive. The MAX3243CUI+G1Z belongs to the MAX3221, MAX3223, and MAX3243 family of low-power RS-232 transceivers. Maxim describes a 1 uA supply-current implementation using AutoShutdown technology. This device is the 3-driver, 5-receiver member and is distinct from lower-channel-count family members by providing five receiver outputs, including the always-active monitoring receiver. The 28-pin TSSOP format supports conventional surface-mount assembly while accommodating the additional receiver and driver connections. Typical applications include industrial serial-port equipment, barcode scanners, point-of-sale terminals, embedded control systems, instrumentation, and systems that connect a controller to multiple RS-232 peripherals. The three driver outputs can support several unidirectional RS-232 links, while five receiver inputs accommodate multiple incoming data or control signals. The 1 uA low-power state is particularly useful where the interface must remain attached to a host without continuously consuming full operating power. Design the circuit with the electrical requirements of RS-232 in mind. Driver outputs require the appropriate external charge-pump and protection network specified by the manufacturer, and receiver inputs should receive protection appropriate to the exposed cable environment. Confirm the complete 28-pin assignment, logic levels, and capacitor values in the manufacturer datasheet before layout release. This product page combines package, channel-count, supply-range, and low-power details with practical selection guidance. It also identifies same-family alternatives and explains where an exact drop-in interchange requires confirmation of temperature grade, suffix code, and exposed loading conditions.

RFQ Contact
MAX3243CUI+T - 3/5 250kbps RS-232 Transceiver | Analog Devices
MAX3243CUI+T

MAX3243CUI+T - 3/5 250kbps RS-232 Transceiver | Analog Devices

Analog Devices MAX3243CUI+T is a 3-driver, 5-receiver full-duplex RS-232 interface transceiver operating from 3 V to 5.5 V, with data rates up to 250 kbps and protection to ±15 kV ESD, housed in a 28-pin TSSOP package. An RS-232 transceiver is an interface integrated circuit that converts logic-level signals into RS-232 voltage levels and converts incoming RS-232 signals back into digital logic. The MAX3243 belongs to the transceiver family within the broader hierarchy of interface ICs, communication semiconductors, and integrated circuits. It is particularly useful where several serial ports share a limited connector or enclosure and low supply current is important. Key features include three RS-232 drivers, five RS-232 receivers, 3 V to 5.5 V operation, and data rates up to 250 kbps. AutoShutdown circuitry detects whether valid receiver activity is present and disables the on-board supply and drivers when the port is inactive. The manufacturer describes a supply current as low as 1 µA during shutdown, making the device suitable for power-conscious embedded and portable equipment. A complementary always-active receiver supports external monitoring in selected applications. The MAX3243 supports both 3.3 V and 5 V system rails. This operating range permits the same transceiver to interface with modern low-voltage CMOS controllers as well as established 5 V logic. Its integrated charge-pump circuitry supports the positive and negative RS-232 voltage levels required by the interface standard, while the ±15 kV ESD rating strengthens protection against cable-connected electrostatic discharge events. Typical uses include industrial control systems, serial-port adapters, test equipment, point-of-sale terminals, data-acquisition equipment, and embedded console interfaces. In a multiport installation, the three drivers can support three outbound channels while five receivers provide inbound monitoring. Designers should nevertheless confirm the required channel direction, electrical standard, connector protection, and system grounding for each cable interface. For layout, place the device close to the connector and route RS-232 traces away from clocks, switching nodes, and sensitive analog inputs. Keep the transmit and receive paths arranged to minimize differential crosstalk, follow the manufacturer’s recommended charge-pump capacitor connections, and provide local supply bypassing. The ±15 kV rating is a device-level specification and does not replace appropriate cable, connector, and board-level protection. This page combines the MAX3243 family specifications, verified ordering information, same-footprint alternatives, and practical interface-design guidance. It also distinguishes confirmed drop-in candidates from alternatives that require pinout and signal-direction review before use in an existing 28-pin TSSOP design.

RFQ Contact