Products (44,000+)

MC14551BFG - 4-Channel 2:1 Analog Multiplexer | onsemi
MC14551BFG

MC14551BFG - 4-Channel 2:1 Analog Multiplexer | onsemi

The onsemi MC14551BFG is a digitally controlled, quad 2:1 analog multiplexer/demultiplexer with four independent switch circuits, a 280 ohm on-resistance, and a 16-pin SOIC package. It is designed for routing analog signals across the complete supply-voltage range and includes low off leakage current for applications requiring accurate signal isolation. An analog multiplexer is a semiconductor switch that connects one common node to one of two selectable signal paths. A demultiplexer reverses that routing function, allowing a shared circuit to select among multiple inputs or outputs. The MC14551B series implements a 4PDT solid-state switch in CMOS technology, placing four independently selectable 2:1 routing sections in one device. This architecture is useful whenever a system must share a limited number of amplifiers, converters, or measurement channels. Key features include four 2:1 switch circuits, 280 ohm on-resistance, low off-state leakage, and control over analog signals across the complete supply range. The device uses digital control inputs with triple-diode protection on the control inputs, helping protect the switching circuitry from excessive input voltage. Its 3 V to 18 V operating supply range and -55 °C to +125 °C temperature range support industrial, communications, instrumentation, and extended-temperature equipment. The MC14551BFG is a single-ended multiplexer with four common terminals and paired switched terminals. Its CMOS implementation provides low power consumption compared with mechanical or relay-based switching while preserving analog signal paths. Because the switch resistance contributes to insertion loss and the leakage current contributes to an error floor, the selected source impedance, signal amplitude, and system bandwidth should be considered during design. Typical applications include data acquisition systems, programmable instrumentation, sensor signal routing, communication path selection, test and measurement equipment, and industrial control systems. The device is particularly useful when several analog sources must be connected to one processing chain while keeping routing compact and repeatable. For PCB implementation, place the device near the signal paths that it routes and keep input and output traces short to minimize parasitic capacitance and pickup. Use a stable supply reference and appropriate bypass capacitance according to the onsemi datasheet. Confirm that control logic levels meet the specified input thresholds and that every selected analog node remains within the allowable signal range. This page combines the manufacturer-linked technical identity, exact distributor package information, drop-in replacement analysis, comparison parameters, and application-focused design guidance for engineers evaluating the MC14551BFG.

RFQ Contact
MC145554P - 13-Bit PCM Codec-Filter | Motorola | Voice
MC145554P

MC145554P - 13-Bit PCM Codec-Filter | Motorola | Voice

The Motorola MC145554P is a 13-bit PCM codec-filter integrated circuit housed in a 16-pin plastic dual inline package. It combines PCM voice digitization and reconstruction with the band-limiting and smoothing functions required by PCM communication systems. Its principal function is to convert analog voice signals into digital PCM data and reconstruct analog audio from received PCM data. A PCM codec-filter belongs to the audio codec and interface hierarchy, where it bridges linear analog audio and digital PCM telecommunications. The codec-filter concept combines signal conversion with frequency-domain filtering in one interface circuit. In a voice system, this integration can reduce the number of separate external filtering stages required around a codec while supporting the bandwidth and smoothing requirements associated with voice transmission. The MC145554 family is designed for per-channel PCM signal processing. The MC145554P identifies the 16-pin plastic DIP configuration, while the 13-bit PCM interface resolution is listed for the exact MC145554P orderable device. Its primary engineering benefit is functional consolidation: analog-to-digital conversion, digital-to-analog reconstruction, band limiting, and smoothing are combined within a single voice-channel interface. The codec-filter family operates with synchronous and asynchronous PCM systems. That flexibility makes the device relevant to telecommunications, voice processing, digital telephony, and embedded audio interfaces where the system clock arrangement differs between endpoints. Designers must still verify clocking, impedance, timing, and analog-interface requirements against the manufacturer datasheet before laying out a new circuit. Typical applications include PCM voice terminals, digital telephone interfaces, speech-processing equipment, voice-band recorders, and telecommunications line-card signal paths. In these systems, the MC145554P provides the conversion boundary between an analog microphone or speaker path and a digital PCM processor. It is especially relevant when a compact single-channel implementation is preferable to separate codec and filter circuitry. A key design consideration is that this is a legacy 16-pin DIP device rather than a modern mixed-signal package. PCB space, assembly method, analog grounding, clock cleanliness, and connector-level signal integrity therefore deserve attention. Reproduction of an existing design should preserve the original footprint, pin functions, timing assumptions, and external component values unless a validated cross-reference has been completed. This product page consolidates the confirmed device identity, PCM interface information, package details, sourcing path, and design considerations into one engineering reference. It also distinguishes documented drop-in replacements from merely similar legacy codec-filter devices, helping engineers determine when PCB reuse is defensible and when a fresh design should use a newer codec architecture.

RFQ Contact
MC145557P - 13-Bit A-Law PCM Codec-Filter | Motorola
MC145557P

MC145557P - 13-Bit A-Law PCM Codec-Filter | Motorola

Motorola, Inc. MC145557P is a single-function A-law PCM codec-filter integrated circuit with 13-bit PCM resolution, offered in a 16-lead PDIP package. It belongs to the MC145554, MC145557, MC145564, and MC145567 family of per-channel devices that combine voice digitization and reconstruction with band-limiting and smoothing functions for PCM communication systems. The component is designed for use in synchronous and asynchronous PCM signal paths. A PCM codec-filter is an interface integrated circuit that processes pulse-code-modulated audio or voice signals between an analog system and a digital PCM channel. Within the broader semiconductor hierarchy, it is a codec and signal-conditioning device within interface ICs, with a more specialized function than a general-purpose audio codec. The MC145557P specifically combines 13-bit PCM processing with A-law encoding in a single 16-lead PDIP package. The principal identified specifications are 13-bit PCM resolution, A-law operation, one codec-filter function, and a 16-pin PDIP package. Its single-function organization makes it suitable for designs that require dedicated per-channel voice conversion rather than a multi-channel codec with additional control and routing functions. The through-hole PDIP format also supports conventional PCB assembly, prototyping, repair, and communication equipment with larger component packages. In a PCM system, the codec-filter provides the conversion and filtering functions needed to digitize voice information, reconstruct received PCM information, and limit the signal band before transmission or processing. Devices in the MC145554, MC145557, MC145564, and MC145567 family perform these per-channel functions and can operate in synchronous or asynchronous systems. The MC145557P is differentiated within that family by its A-law configuration and 13-bit PCM resolution. Typical implementation areas include telephony and voice communication equipment, PCM interface modules, digital voice processing systems, telecommunications line interfaces, and legacy PCM test equipment. Its 16-lead PDIP package may be especially useful where a through-hole footprint is preferred over a surface-mount package, or where the original circuit design already uses this package style. Circuit implementation should follow the Motorola manufacturer datasheet for pin assignment, external component selection, clocking, and signal-path layout. Verify the required A-law system configuration, 13-bit PCM word format, synchronous or asynchronous timing mode, and grounding arrangement before finalizing the PCB. The PDIP footprint also requires adequate lead spacing and clearance from adjacent components. This product overview consolidates the confirmed codec type, PCM resolution, A-law configuration, package format, sourcing context, and functional relationships into an engineering-focused reference. It also provides application guidance, design cautions, package information, and links to the manufacturer documentation needed for an informed design decision.

RFQ Contact
MC14555BF - Dual 1-of-4 CMOS Decoder | onsemi
MC14555BF

MC14555BF - Dual 1-of-4 CMOS Decoder | onsemi

The onsemi MC14555BF is a dual binary-to-1-of-4 decoder/demultiplexer built with complementary MOS enhancement-mode devices, packaged in a 16-pin SOIC. Each decoder section has two select inputs, A and B, an active-low enable input, E, and four mutually exclusive outputs, Q0 through Q3. The selected output switches high while the other three outputs remain low. A nominal 5 V supply and 440 ns propagation delay at a 50 pF load are identified for the device. A decoder or demultiplexer is a combinational logic device that converts a binary selection code into one active output path. The dual architecture provides two independent binary-to-1-of-4 conversion channels in one IC. This hierarchy places the MC14555BF in the CMOS logic family, specifically within decoder and demultiplexer logic ICs used to route control, address, or selection signals. The principal feature is active-high decoding: the selected output goes to the high state, while the three unselected outputs remain low. Two select inputs permit all four output positions to be addressed. An active-low enable input provides a common control function for disabling the decoding network. The complementary MOS construction supports low-power operation and compatibility with conventional CMOS logic systems. The MC14555BF combines two complete decoder/demultiplexer functions in one package, reducing component count in designs that require parallel four-way selection. Its 440 ns propagation delay at a 50 pF load provides useful timing guidance for control paths where propagation delay must remain predictable. The 16-pin SOIC package also supports conventional surface-mount assembly and inspection. Typical uses include four-way control-signal routing, address selection, display or peripheral selection, instrumentation multiplexing, and industrial control logic. Because the device is CMOS and operates from a nominal 5 V supply, it is particularly appropriate for systems using 5 V digital logic levels. The enable input can also support shared bus isolation or synchronized selection in a larger controller. Design with the active-low enable polarity and active-high output polarity clearly in mind. Confirm the voltage ratings, absolute maximum conditions, output drive capability, and timing limits in the onsemi datasheet before finalizing a new design. Place the device so that switching outputs do not unintentionally drive adjacent high-impedance nodes, and validate fanout against every connected load. This product page combines the manufacturer function description, package information, timing indications, application guidance, structured specifications, and engineering design notes to accelerate component evaluation. Request current commercial availability and sourcing terms through the Request a Quote form on this page.

RFQ Contact
MC14556BD - 1-of-4 CMOS Decoder/Demultiplexer | Motorola
MC14556BD

MC14556BD - 1-of-4 CMOS Decoder/Demultiplexer | Motorola

The Motorola MC14556BD is a dual binary to 1-of-4 decoder/demultiplexer built with complementary MOS enhancement-mode devices. It accepts two select inputs, A and B, together with an active-low enable input, E, and routes one of four mutually exclusive outputs, Q0 through Q3, according to the select state. The device operates from 3 V to 18 V, supports operation from -55 °C to 125 °C, and is packaged in a 16-pin SOIC. A decoder/demultiplexer is a logic device that converts binary selection information into one active output path. This makes the MC14556BD useful for control, address decoding, peripheral selection, data routing, and test-point multiplexing. Its four outputs are designed so that only one selected output is active for a valid select combination while the enable input provides an additional gating function. The complementary MOS construction places the device in the 4000-series CMOS logic family. The principal electrical characteristics are a 3 V to 18 V supply range, low-power CMOS operation, and an active-low enable control. The package is a 16-SOIC, also described in listings as SOIC-16 or PDSO16, with a body width of 3.90 mm and a nominal 0.154 inch lead pitch. The operating-temperature range of -55 °C to 125 °C supports industrial and extended-temperature equipment where the additional qualification and sourcing requirements are satisfied. The MC14556BD can decode a two-bit command into one of four mutually exclusive destinations, making it appropriate for selecting one sensor, switching one bank of loads, directing a signal path, or controlling a group of digital peripherals. Because it is a demultiplexer, the enable input can inhibit output activity during reset, initialization, or shared-bus conditions. Designers should account for propagation delay and output transition timing when operating at high system clock rates. For reliable PCB implementation, place the device close to the signals it decodes, route the enable and select nets away from noisy switching nodes, and maintain a common ground reference between the logic device and connected circuitry. Use the manufacturer pin-description and logic diagrams when assigning PCB tracks because the available product documentation does not reproduce a verified pin-by-pin connection table here. This product page combines the device’s verified function, supply range, package, temperature range, and sourcing information with application guidance, comparison parameters, and practical design notes. The result helps engineers identify whether the MC14556BD fits a new decoder/demultiplexer design or whether a different logic function is required.

RFQ Contact
MC14556BF Dual 1-of-4 Decoder/Demultiplexer | onsemi
MC14556BF

MC14556BF Dual 1-of-4 Decoder/Demultiplexer | onsemi

The onsemi MC14556BF is a dual binary-to-1-of-4 decoder/demultiplexer built with complementary MOS enhancement-mode devices, supplied in a 16-pin gull-wing surface-mount package. Each decoder section accepts two select inputs, A and B, and uses the four binary combinations to address four mutually exclusive outputs. A shared active-low Enable input controls whether the selected output path is active, making the device useful for address decoding, data routing, chip selection, and control-signal multiplexing. A decoder/demultiplexer is a digital logic IC that translates a binary address into one active output. It belongs to the decoder hierarchy within combinational logic, interface ICs, and broader semiconductor products. In demultiplexer mode, the MC14556BF routes one selected output according to the A and B inputs. The active-low Enable input provides a common gating function, allowing the selected path to be disabled without changing the select state. The verified device information identifies complementary MOS enhancement-mode construction, two select inputs, one active-low Enable input, and four mutually exclusive outputs labeled Q2 and Q3 within the family description. Its specified temperature grade is military, and the package is described as a rectangular gull-wing SOP with 16 terminals. These characteristics place it in applications that require compact binary decoding alongside conventional through-hole-era logic-package compatibility. Typical uses include selecting one of four peripheral sections, decoding a two-bit control address, separating mutually exclusive commands, and directing a shared signal toward one of four destinations. Because the outputs are mutually exclusive, the active output provides a straightforward way to convert a two-bit binary value into a one-of-four selection without implementing individual Boolean gates at the system level. When laying out a board, place the device near the signals it decodes and route each output according to its assigned destination. Maintain a common ground reference with the controlling logic and connected circuits. Treat all unused inputs according to the manufacturer logic truth table, and do not infer active levels or output polarity from the output names alone. Review the pin-description and truth-table sections in the manufacturer datasheet before finalizing PCB nets. This page consolidates the device identity, package information, decoder architecture, sourcing workflow, comparison framework, and practical design considerations. It also distinguishes documented facts from parameters that require direct confirmation from the manufacturer datasheet, helping engineers plan a review of the MC14556BF without relying on incomplete distributor summaries.

RFQ Contact
MC145572FN - ISDN U-Interface Transceiver 44-PLCC | NXP
MC145572FN

MC145572FN - ISDN U-Interface Transceiver 44-PLCC | NXP

The NXP (formerly Motorola/Freescale) MC145572FN is a single-chip ISDN U-interface transceiver housed in a 44-pin PLCC (Plastic Leaded Chip Carrier) package. It implements the 2B1Q four-level line code defined by ANSI T1.601 for full-duplex digital transmission on a 2-wire metallic loop, supporting basic-rate access on the U reference point between the network termination (NT1) and the line card (LT). The device integrates echo cancellation, adaptive equalization, and a 2B+D (144 kbps) data channel into one CMOS IC originally developed by Motorola Semiconductor. An ISDN U-interface transceiver is the analog front-end IC that bridges digital ISDN terminal equipment with the 2-wire subscriber line. Within the broader telecom IC hierarchy, this places the part under "transceiver" -> "interface IC" -> "telecom IC" -> "specialized/communications IC." U-interface transceivers perform line equalization, adaptive gain control, and 2B1Q pulse-amplitude modulation while handling the long-loop attenuation of standard copper pairs up to approximately 18 kft. Key features of the MC145572FN include integrated 2B1Q codec, on-chip echo canceller, programmable pulse shaping, selectable line build-out for short/long loops, and an 8-bit microprocessor interface for control and status monitoring. The 44-pin PLCC (J-lead) package provides a robust through-hole-style leaded footprint suitable for legacy telecom line-card designs and is rated for the standard 0 to +70C commercial or extended industrial temperature grades depending on the screening option. Architecturally, the MC145572 combines a transmit pulse generator, receive path with adaptive decision feedback equalizer (DFE), and a digital framer/deframer on a single low-power CMOS die. The device operates from a single +5V supply and draws roughly 200 to 350 mW depending on loop length, dramatically simplifying the line card BOM compared to discrete bipolar echo-canceller designs of the early 1990s. It was a flagship IC of the original Motorola ISDN chipset, paired with the MC145574 S/T-interface transceiver and the MC68302 communications controller. Typical applications include ISDN basic-rate U-interface line cards (LT side), NT1 customer-premises equipment, digital loop carrier systems, and early DSL precursor designs. Engineers selected the MC145572FN because it removed the need for a separate analog front-end and DSP for 2B1Q line coding, dramatically reducing board area and time-to-market for ISDN BRI products. When designing with this part, pay close attention to PCB layout for the analog front-end section: keep the transmit and receive paths physically separated, provide a solid analog ground plane under the PLCC, and use the recommended transformer (typically a 1:1.36 or 1:2 turns ratio Pulse PE-68023 or equivalent) for isolation. Note that the MC145572FN has been classified as obsolete or last-time-buy for many years - verify current stock carefully and qualify any substitute thoroughly.

RFQ Contact
MC145572FNR2 - ISDN U-Interface Transceiver, 44-PLCC | NXP
MC145572FNR2

MC145572FNR2 - ISDN U-Interface Transceiver, 44-PLCC | NXP

The NXP (formerly Freescale/Motorola) MC145572FNR2 is an ISDN U-interface transceiver IC housed in a 44-pin PLCC (16.59 x 16.59 mm) J-leaded surface-mount package. It integrates the analog front-end and digital echo-cancellation functions required for full-duplex 2B1Q transmission over a 2-wire ISDN U-interface loop, and is designed to operate as a companion to the MC145574 S/T-interface transceiver in customer-premises equipment (CPE) or network-terminal designs. The device supports 4-wire full-duplex data flow at the standard ISDN Basic Rate Access (BRA) line rate of 160 kbps over twisted-pair copper loops up to approximately 5-6 km. An ISDN U-interface transceiver is a specialized line-interface IC that bridges digital terminal equipment and the 2-wire metallic local loop of the public switched telephone network. In the broader taxonomy, the MC145572FNR2 belongs to the ISDN transceiver family, which sits within telecom interface ICs and ultimately within the broader category of specialized interface ICs. The U-interface (defined in ANSI T1.601) is the reference point between the network termination 1 (NT1) and the line termination (LT) inside the central office; this part targets the network-side or terminal-side adaptive echo-canceller functions that allow 2B1Q baseband signalling to coexist on a single copper pair with echo cancellation. Key features include on-chip 2B1Q line coding/decoding, adaptive echo cancellation, a digital interface that connects to the companion MC145574 S/T device, programmable transmit pulse shaping, and receiver equalization. The die operates from a single +5 V supply and is fabricated in a mature CMOS process that has been qualified for sustained telecommunications deployment. PLCC-44 packaging allows drop-in compatibility with legacy ISDN designs and supports both socketed and surface-mount assembly in production. Typical applications include ISDN BRI terminal adapters, ISDN NT1 network terminations, ISDN-compatible routers, integrated voice/data terminal equipment, and industrial telecom interfaces where 2-wire full-duplex ISDN connectivity is required. Because the U-interface is largely obsolete in regions that have migrated to xDSL, fibre, and 4G/5G wireless, the part is mainly used for legacy support, repair, and equipment that must retain ISDN connectivity. When designing with the MC145572FNR2, ensure the +5 V rail is well-decoupled and that the 2-wire line side meets ANSI T1.601 longitudinal-balance and pulse-mask requirements. Thermal dissipation in the 44-PLCC package is modest because the part does not drive heavy line currents directly, but PCB layout should still provide a low-impedance ground return under the analog section. This page synthesizes distributor pricing, cross-reference alternatives, and practical design notes that are not found in the original Motorola/Freescale datasheet alone, helping engineers sourcing the MC145572FNR2 for legacy support, repair, or new ISDN-CPE designs.

RFQ Contact
MC145572PB - ISDN U-Interface Transceiver, 44-LQFP | NXP
MC145572PB

MC145572PB - ISDN U-Interface Transceiver, 44-LQFP | NXP

The NXP MC145572PB is an ISDN U-interface transceiver housed in a 44-pin LQFP (10x10 mm) package, originally designed by Motorola and later transferred through Freescale to NXP. It is a specialized interface IC operating at 5V with an industrial temperature range of -30C to +85C, supporting data rates of up to 160 kbps for 2B1Q ISDN basic-rate-access (BRA) U-interface applications. An ISDN U-interface transceiver is a type of specialized interface IC that handles the physical-layer signaling between customer-premises equipment (CPE) and the central-office line card over a 2-wire full-duplex digital subscriber loop. Within the broader hierarchy, it sits under interface ICs -> telecom interface ICs -> specialized ICs -> integrated circuits -> semiconductors. The U-interface is the last-mile digital link that operates using echo-cancellation and 2B1Q line coding to deliver two 64-kbps bearer channels plus a 16-kbps D channel over standard twisted-pair copper wiring. Key features include integrated echo cancellation, adaptive equalization, and a 2B1Q line encoder/decoder, all on a single CMOS die. The device requires a single 5V supply and exposes digital serial interfaces for connection to an external S/T-interface transceiver or layer-1 controller. Its 44-LQFP (10x10) package offers a 0.8 mm lead pitch suited to industrial surface-mount assembly, and the industrial temperature grade makes it usable in outdoor customer-premises line units. Typical applications include ISDN basic-rate-access (BRA) terminal adapters, NT1 (Network Termination 1) units for residential and small-business ISDN service, ISDN test equipment, and legacy 2-wire digital-subscriber-loop modems. The 160 kbps line rate supports the standard 144 kbps user payload (2B+D) plus framing overhead. When designing with this part, designers should follow the reference PCB layout in the manufacturer datasheet and provide proper 2-wire transformer isolation between the line side and the digital side. Bulk decoupling on the 5V rail and a low-jitter system clock are required to meet ISDN pulse-template specifications. This page synthesizes distributor pricing, lifecycle status, and pin/packaging facts not consolidated in a single place on the manufacturer's datasheet, including a current cross-reference view of drop-in alternatives that share the 44-LQFP footprint.

RFQ Contact
MC145572PBR2 - ISDN U-Interface Transceiver | NXP | 44-LQFP
MC145572PBR2

MC145572PBR2 - ISDN U-Interface Transceiver | NXP | 44-LQFP

The NXP (formerly Freescale / Motorola) MC145572PBR2 is a single-chip ISDN U-interface transceiver designed for 160 kbps full-duplex 2B1Q transmission over a single twisted-pair copper line. Housed in a 44-pin LQFP (10x10 mm) surface-mount package, this specialized IC integrates the analog front-end, echo canceller, digital signal processor, and HDLC controller required for both the network-termination (NT) and line-termination (LT) sides of an ISDN basic-rate interface, with the side selected at power-up by a single pin. In the broader product hierarchy, the MC145572PBR2 is a specialized telecommunications IC — a sub-category of interface ICs that bridges the physical layer of legacy ISDN and 2B1Q transport systems to higher-layer HDLC processors. It belongs to the MC145572 product family, itself part of Motorola Semiconductor's original MC145xxx CMOS logic lineage that established the part-number convention later continued by Freescale and now NXP. The device operates from a single 5 V supply and consumes considerably less power than the discrete ISDN modem designs it replaced, making it the de-facto standard for U-interface NT1 reference designs, terminal adapters, and ISDN test equipment through the late 1990s and early 2000s. Key features include integrated adaptive echo cancellation, a built-in scrambler/descrambler compliant with ANSI T1.601-1992, an on-chip HDLC controller supporting up to four 16-bit or two 32-bit identifiers, and a Microprocessor-compatible parallel host interface. The transceiver supports both NT and LT modes via a strap pin, includes a programmable digital attenuator, and provides 2B+D channelization with automatic activation/deactivation. Diagnostic loopback and pattern-generation modes aid installation and field troubleshooting by telco technicians. Typical applications include ISDN basic-rate NT1 modems, terminal adapters, digital-loop carrier remote terminals, ISDN test and measurement equipment, and legacy PBX line cards connecting to a U-interface drop. The wide-protocol support also makes the device useful for industrial telemetry bridges that still rely on ISDN for guaranteed low-latency backhaul. When designing with the MC145572PBR2, supply decoupling matters more than for generic logic ICs: place 0.1 uF ceramic capacitors as close as possible to each VDD/VSS pair on the package. Trace the differential transmit pair and receive pair with controlled 100-ohm differential impedance, keep them routed away from switching power and clock lines, and provide at least 6 mm of clearance between the transformer secondary and any digital signal plane to avoid injecting common-mode noise into the receiver's high-gain analog front-end.

RFQ Contact
MC1455BD - 5V Programmable Timer/Oscillator | onsemi
MC1455BD

MC1455BD - 5V Programmable Timer/Oscillator | onsemi

The onsemi MC1455BD is a single 555-type timer and oscillator integrated circuit designed for accurate time delays and free-running oscillation. It operates from a 5 V supply and is packaged in an 8-pin SOIC. The MC1455BD combines a precision timing circuit with trigger and reset inputs, allowing it to be configured as a monostable one-shot or an astable oscillator using external resistors and capacitors. A 555 timer is a type of programmable timer and oscillator within the broader clock and timing IC hierarchy. Its internal comparators, flip-flop, and discharge transistor allow a simple external RC network to determine delay time or oscillation frequency. Compared with a mechanical or discrete timing arrangement, the MC1455BD provides a compact and repeatable implementation for pulse generation, delay, flashing, and periodic control functions. Key features include support for both monostable and astable operating modes, externally adjustable timing through one resistor and one capacitor in monostable operation, and separate trigger and reset terminals. The verified distributor information identifies the device as a 5 V, 555 Type, Timer/Oscillator (Single) IC in an 8-SOIC package. The onsemi datasheet also describes additional terminals for triggering or resetting when required. The MC1455 architecture provides two useful operating behaviors. In monostable mode, a trigger pulse causes the output to enter a defined high state for a duration set primarily by the external timing resistor and capacitor. In astable mode, the output repeatedly switches between high and low states, with the external resistor-capacitor network setting the operating frequency and duty cycle. This makes one device suitable for both one-shot event timing and continuous pulse generation. Typical applications include industrial control timers, LED flashers, pulse generators, delay circuits, repetitive switching circuits, and general-purpose timing modules. Its 8-pin SOIC package supports compact surface-mount PCB layouts, while the external RC components allow timing values to be selected for the particular load and system requirements. The device is also useful as the timing element in educational and prototype circuits where both monostable and astable configurations may be exercised. Designers should select resistor and capacitor values that keep the timing network within the operating limits stated by the manufacturer datasheet and should account for component tolerance when precise timing is required. The trigger and reset pins must be driven only to valid logic levels, and unused or unused-at-a-time inputs should be handled according to the datasheet rather than left floating. PCB layout should keep timing-node connections short and provide an adequate ground return. This page combines verified manufacturer and distributor information, package and pin references, commercial availability, and qualified drop-in alternatives. It also provides application guidance and parameter-level comparison information intended to make timer selection and PCB reuse easier than a raw datasheet summary alone.

RFQ Contact
MC1455BP1G - 5/15V Single Timer | onsemi | DIP-8
MC1455BP1G

MC1455BP1G - 5/15V Single Timer | onsemi | DIP-8

The onsemi MC1455BP1G is a single 555-type timer and oscillator integrated circuit designed for 5 V and 15 V power supplies in an 8-pin PDIP package. It supports monostable time-delay, astable oscillation, and trigger or reset operation, with timing controlled by one external resistor and one capacitor. The device operates from -40°C to +85°C and is supplied in a tube. A monolithic timer is a timing circuit that switches its output after a defined interval. The MC1455 family belongs to the timer and oscillator hierarchy within analog integrated circuits, combining a resistor-controlled timing network with an internal threshold comparator, trigger comparator, output latch, and discharge transistor. In astable mode, the output repeatedly charges and discharges an external capacitor; in monostable mode, one trigger event produces a single timed output pulse. The MC1455BP1G supports supply voltages of 5 V and 15 V and provides separate trigger and reset terminals when those functions are needed. Its resistor-and-capacitor timing architecture allows the delay or oscillation frequency to be established with external components rather than an internal clock. This makes the device suitable for repeatable pulse generation, delay stages, tone generation, and periodic control functions. The circuit combines analog timing thresholds with a logic-level output stage. During astable operation, the external capacitor voltage moves between the internal reference thresholds while the discharge transistor controls the resistor path. The resulting oscillation frequency and duty cycle depend on the selected resistance and capacitance values, so component tolerance directly affects timing accuracy. Monostable operation uses one triggering transition to initiate a single output pulse whose duration is controlled by one timing resistor and capacitor. Typical applications include industrial pulse and delay circuits, oscillator modules, indicator flashing, periodic actuator control, signal-processing test equipment, and educational timer demonstrations. The -40°C to +85°C operating range supports industrial equipment, while the through-hole PDIP package simplifies hand assembly, prototyping, socketed construction, and replacement in legacy designs. Designers should treat the trigger and reset inputs carefully because they influence internal state even when those functions are not used. Verify threshold and discharge-pin behavior against the manufacturer datasheet, maintain stable timing-component tolerances, and provide adequate decoupling between the supply pins and ground. The 5 V and 15 V supply designations should not be treated as a continuous operating range between those points without consulting the device limits. This product record combines the manufacturer timing-circuit description with package, temperature, supply-voltage, and commercial information to support engineering selection. It also provides same-footprint replacement guidance, application-specific design considerations, and a parameter comparison intended to make PCB reuse decisions more transparent.

RFQ Contact
MC1455DG - Single 555 Timer, 16V, 8-SOIC | onsemi
MC1455DG

MC1455DG - Single 555 Timer, 16V, 8-SOIC | onsemi

The onsemi MC1455DG is a single general-purpose 555 timer integrated circuit with a 4.5 V to 16 V supply range, housed in an 8-pin SOIC package. It can generate accurate time delays or free-running oscillations using external resistors and capacitors, while dedicated trigger and reset terminals provide additional control over the timing interval. The device is intended for precision delay, pulse-generation, and oscillator applications in industrial and commercial electronics. A 555 timer is an analog timing integrated circuit that combines a voltage comparator, a flip-flop, discharge transistor, and resistive divider into one reusable building block. Within the broader hierarchy, it is a clock and timing IC within integrated circuits, providing a simple alternative to a dedicated programmable timer or microcontroller-based timing solution. The MC1455 can operate as a monostable one-shot, as an astable oscillator, or as a Schmitt-trigger comparator. The MC1455DG provides a single timer in an 8-SOIC package, operates from 4.5 V to 16 V, and is specified for a 0°C to 70°C temperature range. In monostable mode, one external resistor and one capacitor control the output pulse duration. In astable mode, two resistors and one capacitor establish the oscillation frequency and duty cycle, while the control, trigger, reset, threshold, and discharge pins support the standard 555 application topology. Timing accuracy depends on the external resistor and capacitor tolerances, the device's internal reference behavior, and the operating voltage. Because the trigger input is compared against one-third of the supply voltage and the threshold input is compared against two-thirds of the supply voltage, the timing network sees supply-dependent reference levels. Designers should therefore use stable precision components and avoid high-impedance timing nodes where practical. Typical uses include industrial control pulse generation, relay activation delays, debounce timers, low-frequency oscillators, sensor timeout circuits, and audio-envelope generators. It is also useful in educational and evaluation boards where a simple external-resistor-and-capacitor timing method is preferable to firmware-based timing. For robust layouts, connect the control bypass capacitor close to the control pin, keep the timing capacitor's ground return short, and route the discharge transistor output away from sensitive analog signals. Confirm trigger and reset levels in the selected operating mode because a floating control, trigger, or reset node can produce unintended output transitions. This page combines verified manufacturer and distributor information with pin-level guidance, application fit, comparison parameters, and replacement considerations. It also documents where full electrical limits, qualified pricing, and lifecycle-specific details remain unavailable in the supplied source data.

RFQ Contact
MC1455DR2 - Programmable Timer Oscillator | onsemi
MC1455DR2

MC1455DR2 - Programmable Timer Oscillator | onsemi

The onsemi MC1455DR2 is a single 555-type monolithic timing circuit packaged in an 8-pin SOIC. Designed for accurate time delays or oscillation, it supports time-delay operation controlled by an external resistor-capacitor network and provides trigger and reset terminals. The device is described as a direct replacement for NE555 timers and includes adjustable duty-cycle capability. A timer IC is a specialized timing-control device used to create a defined delay, periodic oscillation, or a repeatable pulse sequence. The MC1455 belongs to the 555 timer family, combining analog threshold comparison and switching functions with external timing components. Within the broader semiconductor hierarchy, it is an integrated circuit, timer and oscillator, and ultimately a signal-generation and control component used in industrial, consumer, and instrumentation electronics. The principal functional characteristics are accurate timing, selectable monostable or astable operating behavior, external resistor-capacitor timing control, trigger support, reset support, and adjustable duty cycle. Its timing network remains external, allowing the designer to select resistance and capacitance values according to the required delay or oscillation frequency. The 8-pin SOIC package also supports compact surface-mount PCB construction while exposing the standard timer functions required for trigger, discharge, control, threshold, reset, output, supply, and ground connections. Technically, the MC1455 combines two internal threshold comparators with a flip-flop and discharge transistor. In time-delay mode, the trigger input initiates a timing interval that is controlled by one external resistor and capacitor. In oscillation mode, the threshold and trigger functions cooperate with the external network to produce a periodic output. Additional trigger and reset terminals provide external control, while the control-voltage terminal supports common waveform-shaping and duty-cycle adjustment techniques described in the manufacturer documentation. Typical uses include pulse generation, delayed switching, debounce and one-shot logic, simple clock circuits, tone generation, warning indicators, and control-signal generation. The part is especially appropriate where a compact, standard 555-type interface is preferred over a more complex microcontroller timer or dedicated clock IC. Its external timing network also allows the timing range to be scaled without changing the package or pinout. The principal design consideration is to use the pin-description table and operating limits in the manufacturer datasheet when assigning signal levels, timing-component values, supply conditions, and output drive requirements. Designers should also review the reset and trigger truth behavior, control-voltage biasing, and discharge-node implementation before placing the circuit in a new PCB design. This page organizes the verified MC1455DR2 product information, commercial inquiry path, drop-in alternatives, pin assignment, comparison points, and practical application guidance. It also distinguishes verified package and interface facts from parameters that require confirmation against the manufacturer datasheet before production release.

RFQ Contact
MC1455DR2G - 4.5-16V Precision Timer Oscillator | onsemi
MC1455DR2G

MC1455DR2G - 4.5-16V Precision Timer Oscillator | onsemi

The onsemi MC1455DR2G is a precision monolithic timer integrated circuit for monostable timing, astable oscillation, pulse shaping, and delay applications. It operates from 4.5 V to 16 V, supports timing intervals from microseconds to hours, and is housed in an 8-pin SOIC package. The device provides trigger and reset terminals in addition to its standard 555 timer functions, allowing external control of timing events. A monolithic timer is an analog timing IC that compares an externally generated voltage with a threshold voltage to control an internal switch. In a 555-family timer, the category hierarchy extends from timer IC to clock and timing IC to analog and mixed-signal semiconductor. The MC1455DR2G can operate as a one-shot monostable circuit, where an external resistor and capacitor set the output pulse width, or as a free-running astable oscillator, where two resistors and one capacitor establish frequency and duty cycle. The MC1455DR2G offers adjustable duty cycle and direct replacement capability for standard NE555 timer circuits. Its trigger and reset inputs support external timing control, while the output stage produces a timing pulse suitable for driving indicator, control, or driver stages. Its 4.5 V to 16 V operating range covers conventional 5 V, 12 V, and 15 V industrial control environments when the timing network and load current are selected appropriately. Internally, the device uses resistor-comparator reference elements, a discharge transistor, and a flip-flop to control the output stage. In astable operation, the timing capacitor charges and discharges between the device's internal trigger and threshold levels. In monostable operation, the trigger input initiates a fixed output pulse determined primarily by one timing resistor and one timing capacitor. These internal functions make the circuit useful wherever a simple, reliable, externally adjustable time base is required. Typical applications include industrial control timers, LED and lamp flashers, pulse generators, debounce circuits, waveform converters, delay stages in test equipment, and audio or modulation tone generators. The trigger terminal also allows the timer to be synchronized by an external event, while the reset terminal provides direct interruption of an active timing cycle. When laying out a timing circuit, place the timing resistor and capacitor close to their associated IC pins to reduce parasitic pickup and timing error. Confirm trigger and reset levels against the external driving circuit, and size the discharge path for the maximum timing-capacitor voltage. Decoupling close to the supply pins is essential when the load produces switching transients. This page combines manufacturer timing characteristics, distributor package information, cross-reference candidates, and practical design guidance. It helps engineers identify pin-compatible options, evaluate the 8-SOIC footprint, and plan monostable or astable implementations without relying only on a distributor catalog listing.

RFQ Contact
MC1455P1G - 555 Timer, 4.5-16V, 8-PDIP | onsemi
MC1455P1G

MC1455P1G - 555 Timer, 4.5-16V, 8-PDIP | onsemi

The onsemi MC1455P1G is a 555-type monolithic timer and oscillator with a 4.5 V to 16 V supply range, housed in an 8-pin PDIP package. It supports accurate time-delay and free-running oscillation functions, with external resistor and capacitor timing components and adjustable duty-cycle operation. Trigger and reset terminals allow the circuit to be initiated or terminated according to the application timing requirements. A 555 timer is a type of timer IC, oscillator IC, and analog integrated circuit used to generate a time-delayed output or periodic waveform without a microprocessor. Within the broader semiconductor hierarchy, the MC1455 belongs to the timer and oscillator category, which sits within clock and timing integrated circuits and analog signal-processing devices. The device provides a simple hardware mechanism for delays, pulse generation, flashing, tone generation, and periodic control. The principal advantages of the MC1455P1G include its direct-replacement positioning for NE555 timers, adjustable duty-cycle capability, separate trigger and reset control, and operation from a single 4.5 V to 16 V supply. Its timing interval is established by one external resistor and capacitor in monostable mode, while astable operation adds the resistor and capacitor connections required to set frequency and duty cycle. These features make the circuit useful in designs where a dedicated timer simplifies control logic. Internally, the MC1455 uses comparator and switching functions to control its discharge, output, trigger, and reset behavior. In monostable operation, a trigger pulse starts one controlled timing interval and then returns the output to its inactive state. In astable operation, the output oscillates continuously, with frequency and duty cycle determined by the external timing network. The manufacturer describes the MC1455 as a highly stable monolithic timing controller, while its trigger and reset terminals support externally controlled operation. Typical uses include LED flashers, interval timers, pulse generators, industrial control timers, switch debounce circuits, simple audio oscillators, and embedded control systems requiring a repeatable hardware timing event. Because the MC1455P1G is a through-hole PDIP device, it is particularly suitable for prototyping, educational assemblies, legacy industrial equipment, and repair designs where a socketed DIP implementation simplifies maintenance. For new layouts, preserve the standard 8-pin timer interface and place timing components close to the relevant pins to reduce parasitic effects. Check trigger and reset pulse timing, discharge-device current, and output-load conditions before finalizing the circuit. A bypass capacitor near the supply pin is recommended when the long timing interval and high timing accuracy required by the design are important. This product record combines manufacturer functional information, package and supply details, cross-reference candidates, and practical design guidance. It also distinguishes verified device attributes from electrical parameters that still require confirmation in the manufacturer datasheet, helping engineers plan a replacement without overlooking timer behavior, package compatibility, or application-level constraints.

RFQ Contact
MC14568BD - Phase Comparator & Programmable Counter | onsemi
MC14568BD

MC14568BD - Phase Comparator & Programmable Counter | onsemi

The onsemi MC14568BD is a CMOS phase comparator and programmable counter integrated circuit that combines a phase comparator, a 100 counter, and a programmable divide-by-N 4-bit binary counter in one 16-pin SOIC package. All internal counting functions are positive-edge triggered, and the complementary MOS construction provides the device family’s defining logic implementation. A phase comparator is a logic component that determines the relationship between two signals, commonly returning a comparison state when the signals agree or differ. A counter is a sequential digital circuit that records successive clock events and generates corresponding binary states. By integrating comparison and counting functions, the MC14568BD supports signal-phase monitoring, periodic event counting, and programmable frequency division within one compact device. The MC14568B family provides a programmable divide-by-N function implemented with a 4-bit binary counter. This architecture allows an incoming event sequence to be reduced to a selected division ratio. The integrated 100 counter provides a separate counting path, while the phase-comparator section supports two-input phase relationships. These functions are useful when a system must derive a slower periodic indication, monitor relative signal timing, or combine counting and comparison behavior. Constructed with MOS P-channel and N-channel enhancement-mode devices, the MC14568BD uses complementary CMOS in a monolithic implementation. CMOS logic provides a natural connection to digital systems because its switching behavior supports low static power in suitable operating states and broad integration with TTL-compatible system logic when operating and interface conditions are properly matched. Typical uses include digital timing and sequencing systems, phase-error indication, programmable pulse division, event counting, periodic clock generation, and industrial control logic. The same integrated architecture can simplify designs that would otherwise require a separate comparator and binary counter, reducing component count and keeping the comparison and counting functions within one device. Designers should verify the supply-voltage range, operating-temperature limits, input thresholds, output-drive capability, and timing characteristics in the manufacturer datasheet before implementation. The divide control and clock-source connections must also be configured according to the datasheet logic table so that the intended division ratio is selected without invalid intermediate states. This product page organizes the MC14568BD function, package information, verified lifecycle data, sourcing route, and practical design guidance. It also identifies the base-family MC14568B alternative while clearly distinguishing it from suffix-specific procurement decisions. Engineering review should always confirm the exact package suffix, pinout, operating limits, and logic behavior before approving a substitution.

RFQ Contact
MC14577CP - Dual Video Amplifier | Motorola | DIP-8
MC14577CP

MC14577CP - Dual Video Amplifier | Motorola | DIP-8

The Motorola MC14577CP is a dual video amplifier integrated circuit packaged in an 8-pin DIP. The device is listed for video amplifier and related signal-processing applications, and distributor listings identify it as a two-channel video amplifier with the package designation 8-PDIP. The MC14577CP is therefore primarily intended for applications requiring two video signal channels in a conventional through-hole package. A video amplifier is an analog integrated circuit used to condition composite, differential, or other video signals before they reach a display, monitor, video processing block, or transmission circuit. In the broader electronics hierarchy, the MC14577CP belongs to the class of amplifier ICs, specifically video amplifiers and modules, rather than being a discrete transistor or a general-purpose digital interface IC. Its dual-channel architecture can reduce the number of separate amplifier packages required in equipment that carries two related video signals. The MC14577CP is associated with the Motorola MC14577 video-amplifier family and is commonly encountered in legacy television, monitor, video-peripheral, and service-equipment designs. The 8-PDIP format makes the device convenient for through-hole prototypes, repair work, and equipment where a leaded package is preferred over a surface-mount package. The “CP” suffix identifies this particular ordering variant and should be retained when comparing it with other family members. Because the device is an older video amplifier, design work should begin with the manufacturer datasheet and the system’s signal levels, impedance requirements, bandwidth expectations, supply arrangement, and allowable distortion. The MC14577CP may be especially relevant when maintaining or reproducing older analog video hardware rather than designing a new compact surface-mount product. The key engineering question is whether the original board requires the MC14577CP’s channel count, gain behavior, supply voltage, input/output impedance, and output-drive capability. In a typical video path, the MC14577CP would sit between a video source and downstream circuitry, with external resistors and capacitors setting gain, bandwidth, coupling, or compensation as required by the application. Its through-hole package supports straightforward prototyping, but designers should still observe the datasheet’s decoupling and grounding recommendations to avoid instability, excessive noise, or channel-to-channel interaction. This product summary combines package and category information with practical replacement guidance. Because equivalent availability is limited, engineers should verify the pinout, electrical limits, and signal-chain requirements directly against the MC14577CP datasheet before substituting any part. For current commercial availability, use the Request a Quote form on this page rather than relying on historical distributor pricing.

RFQ Contact
MC14578P - CMOS Micro-Power Comparator + Voltage Follower | NXP Semiconductors
MC14578P

MC14578P - CMOS Micro-Power Comparator + Voltage Follower | NXP Semiconductors

The NXP Semiconductors MC14578P is a CMOS analog building block that integrates a very-high-input-impedance comparator, a voltage follower, and four enhancement-mode MOSFETs (N-channel and P-channel pairs) on a single die, housed in a 16-pin PDIP (DIP-16) through-hole package. The MC14578 is a micro-power comparator with integrated voltage follower. An LDO (Low-Dropout) linear regulator maintains a stable output voltage, but the MC14578 belongs to a different category - it is a CMOS analog comparator designed for ultra-low-power signal conditioning in battery and line-powered applications. The integrated voltage follower allows monitoring the noninverting input of the comparator without loading the source, which is critical in high-impedance sensor interfaces where the comparator would otherwise distort the signal. The four on-chip MOSFETs (two N-channel and two P-channel) provide design flexibility for level shifting, switching, or simple analog front-ends around the comparator output. Key features include the analog building-block topology that combines comparator, follower, and discrete MOSFETs on one chip, an extremely low quiescent current suitable for battery-powered designs, a CMOS process that delivers very high input impedance, and a single-supply operation that simplifies integration with digital logic. Architecture-wise, the device uses a CMOS process that delivers very high input impedance on the comparator inputs and very low quiescent current consumption, a specification critical for battery-powered designs such as smoke detectors that must operate for years on a single 9V cell. The four co-integrated MOSFETs are positioned as auxiliary building blocks, allowing the designer to build simple transistor circuits around the comparator without external discretes. The combination of the high-impedance follower buffer and on-die MOSFETs is unusual in this package class and is the main architectural reason the part has been a long-term staple in low-cost smoke-detector and sensor-interface designs. Typical applications include line-powered smoke detectors, threshold detectors, liquid/moisture sensors, low-battery detectors, CO detectors and micro interfaces, and pulse shapers. The on-chip MOSFETs simplify typical battery-operated detector front-ends that otherwise would require several discrete transistors. One key design consideration: the on-chip MOSFETs have limited drain current and should not be used as primary power switches - they are sized as signal-path elements. Engineers should review the datasheet's continuous-drain current rating before driving relays or LEDs directly off these transistors. This page synthesizes distributor stock data, drop-in alternatives, and practical design notes not found in the manufacturer datasheet itself.

RFQ Contact
MC14585BD - 4-Bit CMOS Magnitude Comparator | onsemi
MC14585BD

MC14585BD - 4-Bit CMOS Magnitude Comparator | onsemi

The onsemi MC14585BD is a 4-bit CMOS magnitude comparator in a 16-pin SOIC package. It compares two 4-bit binary words presented at inputs A3–A0 and B3–B0, then indicates whether A is less than, equal to, or greater than B through three active-high outputs. The device also provides three cascading inputs so multiple 4-bit sections can be expanded into wider comparison functions without adding a separate priority encoder or equality logic. A magnitude comparator is a digital logic IC that determines the relative order of two binary numbers. Its outputs encode the mathematical relationships A<B, A=B, and A>B, making the comparator a fundamental building block in arithmetic control, sorting, address decoding, test equipment, and digital control systems. The MC14585BD belongs to the CMOS logic family and uses complementary MOS enhancement-mode devices, providing a direct alternative to TTL implementations when system-level logic is already based on CMOS supply rails. The principal features of the MC14585BD are its eight data inputs, three cascade inputs, three active-high comparison outputs, 4-bit comparison width, and 16-pin SOIC format. The cascade inputs allow a more significant 4-bit section to determine the result when lower-order sections are equal. This architecture supports cascaded comparisons for 8-bit, 12-bit, 16-bit, and larger data paths when the corresponding logic states are properly connected. The MC14585BD is intended for conventional CMOS digital systems in which logic thresholds, supply voltage, noise immunity, and propagation delay must be checked against the actual design operating conditions. Because the available manufacturer datasheet identifies the circuit as a CMOS enhancement-mode implementation but does not expose complete electrical-limit tables in the search excerpt, detailed voltage, current, timing, and temperature ratings remain marked where necessary rather than estimated. Typical uses include binary number ordering, digital test fixtures, arithmetic-controller address selection, industrial control logic, embedded comparison functions, and cascading multi-section comparisons. The active-high A<B, A=B, and A>B outputs can feed counters, multiplexers, control-state machines, display logic, or interrupt and status signals in a larger digital system. PCB layout should preserve short input and output traces, provide a solid ground reference, and decouple the power supply near the device. When cascading comparators, route the cascade outputs from the least-significant section into the most-significant section and confirm timing at the system level. The manufacturer datasheet pin-description table should be used as the authority when assigning tracks and probing the 16-pin footprint. This page organizes the manufacturer function description, pin map, verified package information, qualified drop-in comparisons, application guidance, and practical implementation notes. It is designed to help engineers move quickly from device identification to schematic review and PCB-level design decisions while keeping unresolved electrical details explicit.

RFQ Contact
MC1458D - Dual 1MHz Op Amp, ±15V, 8-SOIC | Texas Instruments (Tape & Reel)
MC1458D

MC1458D - Dual 1MHz Op Amp, ±15V, 8-SOIC | Texas Instruments (Tape & Reel)

The Texas Instruments MC1458D is a dual general-purpose operational amplifier integrating two internally compensated op amps in an 8-pin SOIC (D) package, originally designed to be pin-compatible with the classic Motorola MC1458 and Signetics N5558/S5558 parts. Each channel delivers a gain bandwidth product of 1 MHz with a 0.5 V/us slew rate and operates from split supplies of plus/minus 5 V to plus/minus 15 V, or equivalently from a single supply of 10 V to 30 V. The output stage swings within a few volts of each rail, and the inputs cover the full common-mode range including the negative rail, which simplifies single-supply signal-conditioning designs. An operational amplifier (op amp) is a high-gain DC-coupled voltage amplifier with differential inputs and a single-ended output. In the system hierarchy, the MC1458D sits as a general-purpose linear IC under amplifier ICs, which itself belongs to the broader family of analog signal-conditioning components and integrated circuits. The MC1458D is specifically a dual-channel, internally compensated design that requires no external frequency-compensation capacitor, simplifying PCB layout versus discrete-transistor op-amp implementations. Key features include short-circuit protection on the output stage, low power consumption of approximately 1.7 mA per amplifier at plus/minus 15 V, no latch-up, and wide common-mode plus differential voltage ranges. The two channels share a single bias network, giving matched DC behavior that suits difference amplifiers, active filters, and dual-channel transducer signal chains. Each channel is a complete bipolar op amp with internal compensation, allowing the part to be used as a direct functional replacement for legacy 1458-family designs with no circuit changes. Architecturally, the MC1458D uses a classic bipolar transistor input stage with an active load, a Darlington intermediate stage, and a class-AB complementary emitter-follower output, mirroring the topology of the uA741 but with two channels on one die. The dual-die design eliminates the need for an external compensation capacitor on each channel; instead, the internal capacitor is trimmed during wafer test. This mature architecture trades raw speed for excellent DC accuracy, low input bias current relative to JFET alternatives, and predictable behavior over the full 0 to 70 degrees C commercial temperature range. Typical applications include active filtering, transducer signal conditioning, instrumentation front ends, integrators and comparators, audio preamplifiers, and general-purpose dual-channel amplification in industrial controls and consumer electronics. The matched pair also makes it well-suited for differential amplifiers driving downstream ADCs. When designing with this part, observe the absolute maximum differential input voltage of plus/minus 30 V and ensure the input common-mode range is respected to avoid phase inversion. Bypass supplies with a 0.1 uF ceramic capacitor close to the VCC+ and VCC- pins to prevent oscillation in unity-gain buffer configurations. This page synthesizes distributor pricing, drop-in replacement candidates for the dual 1458 pinout, and practical design notes not consolidated in the manufacturer datasheet.

RFQ Contact
MC1458DE4 - Dual 1 MHz Op Amp | Texas Instruments
MC1458DE4

MC1458DE4 - Dual 1 MHz Op Amp | Texas Instruments

Texas Instruments MC1458DE4 is a dual general-purpose operational amplifier with two independently usable amplifier circuits, a 1 MHz gain-bandwidth product, and a 0.5 V/µs slew rate. The device is packaged in an 8-pin SOIC measuring 0.154 inch, or 3.90 mm, in width. It is intended for general-purpose analog signal conditioning and is described as a dual operational amplifier whose internal frequency compensation eliminates the need for external compensation components. An operational amplifier, or op amp, is a voltage-gain building block within analog and mixed-signal electronics. MC1458DE4 belongs to the general-purpose operational-amplifier class and contains two amplifier channels in one package. Its internally compensated architecture simplifies circuit construction in voltage followers, summing amplifiers, comparators, and general signal-conditioning networks. The two channels can process different analog signals or can be used together for filtering, instrumentation, and differential circuit functions when the application requires it. Key characteristics include two amplifier circuits, a 1 MHz gain-bandwidth product, a 0.5 V/µs slew rate, a 15 V supply designation, and integrated frequency compensation. The manufacturer describes the amplifier as low-power, protected against latch-up, and intended for voltage-follower use. Unlike implementations that expose offset-null terminals, the MC1458 family is described as having each amplifier half electrically similar to a µA741 without offset-null capability. The absence of those terminals simplifies the pin assignment and reduces external component count. The internally compensated amplifiers provide stable operation in voltage-follower configurations without external frequency-compensation networks. Their approximately 1 MHz bandwidth is suitable for audio-frequency and general instrumentation signal paths where moderate bandwidth is sufficient. The 0.5 V/µs slew rate determines how rapidly output voltage can follow a changing input, making the device appropriate for general analog amplification rather than high-speed pulse or wideband signal processing. Typical uses include audio preamplification, summing and averaging amplifiers, voltage followers, sensor signal conditioning, comparator-style threshold circuits, and educational or laboratory analog designs. The 8-pin SOIC package allows two amplifier channels to be placed on a compact through-hole PCB footprint, while the device's two-circuit organization can reduce component count when both positive and negative signals are processed. Designers should account for supply headroom, common-mode input range, output swing, and the bandwidth available at the selected closed-loop gain. Decoupling capacitors should be placed close to the supply pins, and sensitive analog layouts should minimize trace resistance and coupling from switching circuitry. The most important sourcing check is pinout and footprint compatibility, because different package suffixes of the MC1458 family can use different standard packages. This product page consolidates the MC1458DE4 electrical identity, package information, practical use cases, verified source links, and design guidance. It also distinguishes confirmed drop-in candidates from package or electrical variants, helping engineers evaluate replacements without assuming that a similar amplifier description guarantees a compatible PCB footprint.

RFQ Contact
MC1458DR - Dual 1MHz Op Amp, ±15V, 8-SOIC | Texas Instruments
MC1458DR

MC1458DR - Dual 1MHz Op Amp, ±15V, 8-SOIC | Texas Instruments

The Texas Instruments MC1458DR is a dual general-purpose operational amplifier integrating two internally compensated op amps in an 8-pin SOIC (D) package, originally designed to be pin-compatible with the classic Motorola MC1458 and Signetics N5558/S5558 parts. Each channel delivers a gain bandwidth product of 1 MHz with a 0.5 V/us slew rate and operates from split supplies of plus/minus 5 V to plus/minus 15 V, or equivalently from a single supply of 10 V to 30 V. The output stage swings within a few volts of each rail, and the inputs cover the full common-mode range including the negative rail, which simplifies single-supply signal-conditioning designs. An operational amplifier (op amp) is a high-gain DC-coupled voltage amplifier with differential inputs and a single-ended output. In the system hierarchy, the MC1458DR sits as a general-purpose linear IC under amplifier ICs, which itself belongs to the broader family of analog signal-conditioning components and integrated circuits. The MC1458DR is specifically a dual-channel, internally compensated design that requires no external frequency-compensation capacitor, simplifying PCB layout versus discrete-transistor op-amp implementations. Key features include short-circuit protection on the output stage, low power consumption of approximately 1.7 mA per amplifier at plus/minus 15 V, no latch-up, and wide common-mode plus differential voltage ranges. The two channels share a single bias network, giving matched DC behavior that suits difference amplifiers, active filters, and dual-channel transducer signal chains. Each channel is a complete bipolar op amp with internal compensation, allowing the part to be used as a direct functional replacement for legacy 1458-family designs with no circuit changes. Architecturally, the MC1458DR uses a classic bipolar transistor input stage with an active load, a Darlington intermediate stage, and a class-AB complementary emitter-follower output, mirroring the topology of the uA741 but with two channels on one die. The dual-die design eliminates the need for an external compensation capacitor on each channel; instead, the internal capacitor is trimmed during wafer test. This mature architecture trades raw speed for excellent DC accuracy, low input bias current relative to JFET alternatives, and predictable behavior over the full 0 to 70 degrees C commercial temperature range. Typical applications include active filtering, transducer signal conditioning, instrumentation front ends, integrators and comparators, audio preamplifiers, and general-purpose dual-channel amplification in industrial controls and consumer electronics. The matched pair also makes it well-suited for differential amplifiers driving downstream ADCs. When designing with this part, observe the absolute maximum differential input voltage of plus/minus 30 V and ensure the input common-mode range is respected to avoid phase inversion. Bypass supplies with a 0.1 uF ceramic capacitor close to the VCC+ and VCC- pins to prevent oscillation in unity-gain buffer configurations. This page synthesizes distributor pricing, drop-in replacement candidates for the dual 1458 pinout, and practical design notes not consolidated in the manufacturer datasheet.

RFQ Contact
MC1458DR2 - Dual Internally Compensated Operational Amplifier | onsemi
MC1458DR2

MC1458DR2 - Dual Internally Compensated Operational Amplifier | onsemi

The onsemi MC1458DR2 is a dual, internally compensated operational amplifier designed for general-purpose analog signal processing. It provides two amplifier circuits in an 8-pin SOIC package and is specified for operation from a single positive supply, making it suitable for audio, instrumentation, control, and active-filter applications. The device uses bipolar construction and is optimized for applications using external feedback components, including summing amplifiers, integrators, and conventional closed-loop amplifier stages. The MC1458 family combines a high-performance dual amplifier with internal frequency compensation. Internal compensation removes the need for an external dominant-pole capacitor in many standard feedback configurations, while external feedback resistors still determine gain, bandwidth, input impedance, and signal behavior. This makes the MC1458DR2 practical for designs that require a straightforward dual-amplifier solution rather than a highly integrated modern rail-to-rail amplifier. Key operating characteristics include low input offset voltage, low input bias current, broad common-mode input range, and a dual-amplifier configuration in a compact surface-mount package. The internal compensation is designed for stable operation with resistive feedback networks, allowing the device to be used in non-inverting, inverting, voltage-follower, summing, and active-filter circuits. The two amplifiers share a common power supply and ground connection while maintaining separate differential inputs and outputs. Typical uses include small-signal audio channels, sensor-conditioning stages, analog summing networks, waveform shaping, integrators, and low-frequency control loops. The 8-pin SOIC footprint is also convenient for designs that previously used 8-pin dual operational amplifiers. Because this is an older bipolar amplifier family, engineers should verify the exact supply voltage, common-mode range, output swing, slew rate, and input/output current limits against the manufacturer datasheet before finalizing a new design. For PCB design, place the device close to the feedback network and bypass pins, route high-impedance input and compensation-related nodes with short traces, and maintain a quiet ground reference. Decoupling capacitors should be positioned close to the supply pins, while analog input traces should be separated from switching and digital return paths. The dual architecture allows two related signal paths to be implemented with one package, reducing component count and simplifying board layout. This product page combines the manufacturer and distributor references, package information, technical use cases, comparison fields, and practical design guidance for engineers evaluating the MC1458DR2 as a dual operational-amplifier choice.

RFQ Contact