بەرهەمەکان (3,600+)

PCM56P-J - 16-Bit Audio DAC | Texas Instruments
PCM56P-J

PCM56P-J - 16-Bit Audio DAC | Texas Instruments

The Texas Instruments PCM56P-J is a series-input, 16-bit monolithic digital-to-analog converter for precision audio signal generation, with a 16-pin PDIP package. It converts serial PCM data into an analog voltage output and is factory-trimmed and tested for critical audio specifications. The device supports 16-bit resolution, 15-bit typical monotonicity, up to 96 dB dynamic range, and no external components are required according to the manufacturer datasheet. A digital-to-analog converter, or DAC, converts digital audio samples into a continuous analog voltage signal. The PCM56 belongs to the signal-conversion IC hierarchy and is used in audio DAC, digital audio equipment, and precision signal-generation systems. Its series input reduces the number of parallel data lines required, while the monolithic converter provides a compact solution for generating an analog output from PCM-formatted data. Key features include 16-bit resolution, 15-bit typical monotonicity, 96 dB dynamic range, and differential linearity error characterized in the family documentation. The J-grade part is identified by the PCM56P-J ordering code and uses the same 16-pin PDIP format associated with the PCM56 family. The converter is factory-trimmed and tested because audio DAC performance depends on total harmonic distortion, differential linearity, bipolar zero error, temperature shifts, and settling time. The PCM56P-J is intended for applications where a serial PCM stream must become an analog audio or instrumentation signal. Its 16-bit format supports high-resolution digital audio, while the converter's factory calibration helps reduce mismatch-related distortion. The family datasheet also identifies molded-plastic DIP and SOIC packaging options, although PCM56P-J specifically corresponds to the PDIP variant shown by distributor records. Typical uses include digital audio playback, audio test equipment, precision signal generators, and embedded audio systems. In an audio path, the PCM56 can be driven by a serial audio source and followed by an output amplifier or line driver. Designers should verify interface timing, supply requirements, analog output loading, and external filtering against the manufacturer datasheet before finalizing a board. A key design consideration is that this is a legacy monolithic audio DAC rather than a modern integrated audio codec. System design should account for its separate digital interface and analog output stage, and should confirm availability before committing new production layouts. The 16-pin PDIP footprint also requires through-hole board space rather than a compact surface-mount footprint. This page combines the verified Texas Instruments family description, distributor listing data, package information, and practical replacement guidance. It separates confirmed PCM56P-J attributes from specifications that require the full datasheet or device-specific verification.

RFQ پەیوەندی
PCM56P-K - 16-Bit High-Fidelity Audio DAC | Texas Instruments
PCM56P-K

PCM56P-K - 16-Bit High-Fidelity Audio DAC | Texas Instruments

Texas Instruments PCM56P-K is a 16-bit monolithic digital-to-analog converter with serial input, a K-grade low-distortion specification, and a 16-pin PDIP package. It supports dual power supplies from ±5 V to ±12 V, delivers 96 dB dynamic range, and is factory trimmed and tested for critical audio specifications. A digital-to-analog converter, or DAC, converts digital PCM audio samples into proportional analog voltages or currents. The PCM56 belongs to the broader hierarchy of signal-conversion ICs, audio DACs, data converters, and semiconductor components. Its self-contained architecture combines a stable low-noise internal zener reference, high-speed current switches, a resistor ladder, and a low-noise output operational amplifier on one monolithic chip. The K grade provides maximum THD of -92 dB with full-scale input and maximum THD of -74 dB with a -20 dB input. Typical monotonicity is 15 bits, corresponding to 0.001% of full scale, and typical differential linearity error is 0.001% of full scale. These characteristics make the converter suitable for high-fidelity audio equipment where distortion, linearity, and noise can affect signal quality. Serial data is accepted through the converter interface, while current switches and the resistor ladder reconstruct the analog output. The internal reference and output amplifier reduce the number of external precision components required. With ±5 V supplies, power dissipation is typically less than the value reported for higher-supply operation in the manufacturer datasheet, making supply selection important in compact audio products. Typical applications include digital audio mixers, CD-player and digital-audio output stages, professional audio equipment, instrumentation, and high-resolution signal-generation systems. The part can also be used in legacy designs where an established 16-bit serial DAC and PDIP footprint simplify PCB replacement or preservation of an existing analog architecture. Designers should verify clock format, data timing, analog output loading, supply sequencing, and output filtering against the manufacturer datasheet. The 16-pin PDIP package is not ideal for compact modern equipment, so PCB area and mechanical compatibility should be confirmed before selecting this converter for a new high-density design. This product record combines the verified manufacturer specifications, distributor sourcing information, and same-brand drop-in guidance in one engineering-focused reference. It also distinguishes the K-grade performance position from lower PCM56 grades and identifies the PCM61P-K as a reported pin-compatible upgrade candidate.

RFQ پەیوەندی
PCM56P-L - 16-Bit Audio DAC | Texas Instruments
PCM56P-L

PCM56P-L - 16-Bit Audio DAC | Texas Instruments

The Texas Instruments PCM56P-L is a series-input 16-bit monolithic digital-to-analog converter designed for high-fidelity audio signal generation. It provides 16-bit resolution, 96 dB dynamic range, and a stated -92 dB maximum total harmonic distortion for the K-grade full-scale condition identified in the series datasheet. The PCM56P-L is supplied in the 16-pin molded plastic DIP package and operates from dual supplies ranging from ±5 V to ±12 V. A digital-to-analog converter is an integrated circuit that converts a digital audio code stream into a proportional analog voltage or current. The PCM56 belongs to the DAC family within the broader ADC/DAC and signal-conversion hierarchy. Its internal architecture combines a stable low-noise zener voltage reference, high-speed current switches, a resistor ladder network, and a fast-settling low-noise output operational amplifier on one monolithic chip. The series datasheet identifies no external components as required for the converter core, while factory trimming and testing support the critical audio specifications. The device is intended for applications where low distortion, stable reference behavior, and controlled settling are important. The PCM56P-L designation identifies the -L grade, so designers should use the manufacturer ordering table and datasheet grade limits when comparing it with other PCM56 variants. Typical uses include CD-player audio paths, digital audio decoding systems, instrumentation, waveform generation, and other audio DAC circuits that accept serial digital data. Dual positive and negative supplies are required by the series architecture, and the analog output stage should be evaluated against the selected load, grounding, decoupling, and signal-chain requirements. The principal design consideration is ensuring adequate supply headroom and clean reference behavior. Follow the datasheet's recommended decoupling and layout practices, observe the specified supply range, and account for settling time when driving subsequent analog stages. The PCM56 is an audio-focused converter rather than a generic waveform DAC, so its performance claims should be evaluated at the signal levels, frequencies, and loads relevant to the intended audio path. This page combines the verified manufacturer and distributor descriptions, identifies the important architecture and orderable package facts, and separates verified data from parameters that require design-specific confirmation. It is intended to support sourcing, comparison, and first-pass engineering review without replacing the complete manufacturer datasheet.

RFQ پەیوەندی
PCM56U - 16-Bit Serial Audio DAC | Texas Instruments
PCM56U

PCM56U - 16-Bit Serial Audio DAC | Texas Instruments

The Texas Instruments PCM56U is a 16-bit, serial-input, monolithic digital-to-analog converter with one audio output channel and a 16-pin SOIC (DW) package. The verified distributor data identifies it as an audio DAC with a 16-bit resolution, while the manufacturer result describes the PCM56 family as a series-input 16-bit monolithic DAC. A companion third-party listing specifies bipolar operation, a 5 V dual supply, and a surface-mount SOIC package. A digital-to-analog converter, or DAC, converts digital audio samples into a proportional analog voltage or current. A DAC belongs to the ADC/DAC hierarchy, which sits inside data-converter and signal-conversion semiconductors used to connect digital signal-processing systems to analog audio paths. The PCM56U is therefore suited to digital audio engines, CD and digital-audio player analog stages, test equipment, and other systems requiring a discrete high-resolution audio conversion function. The verified PCM56U data supports a one-channel, 16-bit architecture in a 16-pin SOIC package. Its serial digital input allows a digital audio source to provide successive PCM samples, while the analog output provides the corresponding conversion signal. The manufacturer search result specifically describes the family as a series-input device, making interface timing and data format important parts of system integration. The PCM56U is available through multiple distributor channels, including DigiKey, Mouser, and Octopart. The manufacturer also provides an official PCM56U part-details page and a datasheet PDF. The retrieved data does not establish the device's lifecycle status, exact input format, dynamic-range value, conversion rate, output type, or full electrical limits; those parameters are therefore not inferred here. Engineers should use the manufacturer datasheet for definitive values before designing a new PCB. The PCM56U's 16-pin SOIC package makes it relevant to through-hole-style legacy audio boards and repair or upgrade work where an existing footprint is already available. Because the retrieved cross-reference results do not identify a verified same-package, pin-compatible replacement, replacement selection should be treated cautiously. A different DAC with the same resolution is not automatically a drop-in substitute because interface timing, supply rails, reference voltage, analog output topology, and pin assignment must all match. This page synthesizes the verified distributor identity, manufacturer datasheet links, package information, sourcing references, and cross-reference limitations. It does not convert unverified catalog snippets into unsupported electrical specifications. For purchasing, use the distributor listings and request current price, inventory, lead time, and lifecycle confirmation directly from the supplier. For design-in, download the official PCM56 datasheet and compare every electrical and timing parameter with the target system.

RFQ پەیوەندی
PCM56U/1K - 16-Bit Audio DAC | Texas Instruments | SOIC-16
PCM56U/1K

PCM56U/1K - 16-Bit Audio DAC | Texas Instruments | SOIC-16

The Texas Instruments PCM56U/1K is a series-input 16-bit monolithic digital-to-analog converter for audio signal generation, available in a 16-pin SOIC package. The device provides a 16-bit resolution, 15-bit typical monotonicity, 96 dB dynamic range, and K-grade total harmonic distortion of -92 dB maximum at full-scale input. Its architecture combines a stable internal zener voltage reference, high-speed current switches, a resistor ladder network, and a fast-settling low-noise output operational amplifier on one monolithic chip. The converter is designed for precision audio applications requiring accurate full-scale output behavior, low distortion, and stable operation over temperature and time. The PCM56 is a digital-to-analog converter, or DAC, within the broader integrated-circuit hierarchy that includes ADC/DAC converters, data-conversion ICs, and signal-processing semiconductors. Its function is to convert serial digital audio samples into a continuous analog voltage. The PCM56U/1K accepts a serial input format and uses dual power supplies ranging from ±5 V to ±12 V. The converter is factory-trimmed and tested for critical specifications, including total harmonic distortion, differential linearity, bipolar zero error, and settling-time effects on accuracy. Important K-grade characteristics include -92 dB maximum THD at full-scale input and -74 dB maximum THD at -20 dB input. The device also provides 96 dB dynamic range and requires no external components for its core conversion function. These characteristics make it suitable for professional audio equipment, instrumentation, digital audio synthesis, laboratory signal sources, and other systems where a low-noise analog output is required. The monolithic implementation reduces the number of external precision components required around the converter. The PCM56U/1K operates from dual supplies that can range from ±5 V to ±12 V, while the verified distributor listing identifies a 4.75 V to 13.2 V supply indication. The 16-pin SOIC package supports conventional surface-mount PCB assembly. The device is identified by DigiKey as a 16-bit PCM audio DAC in a 16-SOIC package, and Mouser lists the PCM56U/1K as a 16-bit monolithic audio DAC. The Texas Instruments product page and datasheet remain the authoritative references for ordering information, pin functions, electrical limits, and application details. When designing around the PCM56U/1K, verify the required serial interface timing, analog output implementation, supply sequencing, and signal-ground arrangement against the manufacturer datasheet. The dual-supply architecture and internal reference are important system-level considerations. This page consolidates distributor availability information, manufacturer documentation, package details, comparison data, and practical design guidance for engineers evaluating the PCM56U/1K.

RFQ پەیوەندی
PCM56U/1KG4 - 16-Bit Mono Audio DAC | Texas Instruments
PCM56U/1KG4

PCM56U/1KG4 - 16-Bit Mono Audio DAC | Texas Instruments

The Texas Instruments PCM56U/1KG4 is a 16-bit serial-input monolithic digital-to-analog converter for audio signal generation, featuring a PCM data interface, 96 dB dynamic range, and a 16-pin SOIC package. The K-grade device supports full-scale THD of -92 dB maximum, while its -20 dB-input THD is -74 dB maximum. It operates from -25 °C to +70 °C and is supplied in tape-and-reel packaging. A digital-to-analog converter, or DAC, converts digital audio samples into a proportional analog voltage or current. The PCM56 belongs to the broader hierarchy of DAC, data converter, signal-conversion IC, and semiconductor. Unlike a general-purpose numerical DAC, this device is optimized for audio applications where total harmonic distortion, dynamic range, settling behavior, linearity, and stability over time and temperature are primary performance considerations. The PCM56U/1KG4 accepts serial PCM data and provides 16-bit resolution without external components. Its K-grade characterization distinguishes the maximum distortion performance at full-scale input from operation with a signal 20 dB below full scale. Factory trimming and testing are applied to the critical conversion specifications, reducing the need for user calibration while supporting repeatable audio output performance. Internally, the converter combines a serial digital interface, a precision conversion core, and an internal voltage reference. The supported analog supply range is approximately ±4.75 V to ±13.2 V, allowing operation from conventional bipolar audio rails. The 16-pin molded SOIC package supports conventional surface-mount assembly while retaining the pinout and package arrangement associated with the PCM56 family. Typical uses include professional digital audio equipment, CD and digital-audio player output stages, synthesizer and effects-renderer digital-to-analog conversion, broadcast equipment, and precision audio test systems. In these systems, the device can generate a mono analog output from a serial PCM stream while its specified distortion and dynamic-range limits help determine the audible noise and linearity floor of the downstream output stage. System design should preserve the converter's specified supply range, provide stable bypass capacitance at the analog and digital supply pins, and use an appropriate reconstruction or anti-imaging filter after the analog output. PCB signal-routing practices should keep digital clock and data traces away from sensitive analog output nodes, while grounding and return-current paths should follow the pin-description and layout guidance in the manufacturer datasheet. This product page combines the manufacturer's technical information, package and lifecycle characterization, practical application guidance, and qualified drop-in comparison data. It is intended to help engineers determine whether the PCM56U/1KG4 fits an existing 16-pin SOIC audio-conversion design and how candidate replacements differ in package, grade, and conversion specifications.

RFQ پەیوەندی
PCM56UG4 - 16-Bit Audio DAC | Texas Instruments | 16-SOIC
PCM56UG4

PCM56UG4 - 16-Bit Audio DAC | Texas Instruments | 16-SOIC

The Texas Instruments PCM56UG4 is a 16-bit serial-input audio digital-to-analog converter with a 16-SOIC package, dual supply operation, and a nominal settling time of 1.5 microseconds. It converts serial PCM audio data into an analog output for professional audio, instrumentation, and data-acquisition equipment. The verified product information identifies the converter as a monolithic DAC with a 16-bit resolution and a commercial operating grade. A digital-to-analog converter is a signal-conversion IC that transforms digital PCM data into a continuously variable analog voltage or current. The PCM56UG4 belongs to the DAC family within the broader ADC/DAC and data-converter hierarchy. Its serial interface reduces the number of parallel data lines required, making it suitable for compact audio systems where board area and signal routing are important. The 16-SOIC package is also compatible with conventional surface-mount assembly and tube packaging. The verified data highlights 96 dB dynamic range and maximum total harmonic distortion values of -92 dB at full-scale input and -74 dB at -20 dB input for the K-grade device. These figures make the part relevant to precision audio paths where distortion and noise can affect perceived signal quality. The converter is factory trimmed and tested for critical specifications, according to the available manufacturer datasheet material. The PCM56UG4 uses a factory-trimmed ladder and scaling network with matched analog circuitry. The manufacturer material explains that conversion errors can arise from linearity, matching and tracking behavior, supply rejection, and reference errors. This makes careful power-supply design, grounding, and output-stage implementation important for achieving the rated performance in a finished audio product. Typical applications include digital mixing consoles, professional audio interfaces, audio recording equipment, digital test and measurement systems, and signal-generation equipment. The device can be used where a 16-bit PCM stream must be converted into an analog audio signal while preserving low distortion and adequate dynamic range. Designers should provide clean, symmetrical supply rails and follow the manufacturer’s recommended input, output, and decoupling arrangements. The dual supply requirement must be checked against the target system’s analog rails, while the output network should be designed for the intended load and signal level. The PCM56UG4 should not be selected solely by package and bit depth; interface timing, output amplitude, settling behavior, and system-level noise must also be verified.

RFQ پەیوەندی
PCM6340QRTVRQ1 - 4-Ch Audio ADC w/ Mic Bias | TI Automotive
PCM6340QRTVRQ1

PCM6340QRTVRQ1 - 4-Ch Audio ADC w/ Mic Bias | TI Automotive

The Texas Instruments PCM6340QRTVRQ1 is an automotive-grade, 4-channel, 32-bit audio analog-to-digital converter (ADC) supporting sample rates from 8 kHz to 768 kHz in a 32-pin WQFN (RTV) 5x5 mm package. The device accepts analog input signals up to 10 V RMS, includes integrated microphone bias generation, and provides input fault diagnostics, making it a single-chip analog front end for in-vehicle audio capture. What is an audio ADC? An audio analog-to-digital converter is a semiconductor that samples continuous analog audio signals and converts them into a digital stream (typically PCM, TDM, or I2S) for downstream DSP, codec, or microcontroller processing. In automotive audio signal chains, audio ADCs sit between the analog microphone or line-input stage and the digital host processor; the broader hierarchy is ADC -> data converter -> mixed-signal IC -> semiconductor. The PCM6340QRTVRQ1 belongs to TI's PCM6xx0-Q1 family of automotive audio ADCs and combines the converter, microphone bias supply, and input diagnostics into one part, which simplifies BOM and PCB area versus discrete implementations. Key features include four high-performance delta-sigma ADC channels with 16/20/24/32-bit output word lengths, support for both single-ended and differential input configurations, integrated programmable microphone bias, and input fault diagnostics (open, short, DC level). The device is controlled through I2C or SPI and outputs audio data over standard serial audio interfaces. It supports line and microphone inputs with input signals up to 10 V RMS. Technically, the PCM6xx0-Q1 family uses a high-order delta-sigma modulator architecture with multi-bit front-end and on-chip digital decimation filtering, achieving high dynamic range and low distortion. The integrated microphone bias regulator eliminates external LDO/charge-pump circuitry, while the input diagnostics monitor each channel for open/short conditions and DC fault levels that are critical for automotive functional-safety requirements. Typical applications include automotive head-unit audio capture, active-noise-cancellation (ANC) and road-noise-cancellation (RNC) microphone arrays, in-cabin voice and hands-free EC/NR front ends, telematics and eCall microphone inputs, and automotive infotainment line-input digitizers. Designers choose this part when they need AEC-Q100-qualified capture with on-chip mic bias and diagnostics to reduce PCB area and improve ASIL-level fault coverage. When designing with this part, follow the datasheet's recommended decoupling scheme and place the analog and digital ground returns per the layout guidelines to meet the stated THD+N and dynamic-range numbers. Use the -enable pin and the configurable power-down modes to manage quiescent draw on accessory-rail battery lines. This page synthesizes distributor pricing, drop-in alternatives from TI's PCM6xx0-Q1 family and competing automotive ADCs, and practical design notes not duplicated in the manufacturer datasheet.

RFQ پەیوەندی
SC510379AZCFU - Freescale ADC IC | NXP Legacy
SC510379AZCFU

SC510379AZCFU - Freescale ADC IC | NXP Legacy

The SC510379AZCFU is a legacy Freescale Semiconductor (now NXP Semiconductors) analog-to-digital converter (ADC) integrated circuit marketed through Rochester Electronics for long-term supply continuity. Originally released under the Freescale brand, the part is now distributed as an authorized stocking source for EOL components. Per distributor listings on DigiKey Marketplace and Octopart, the device is sold through authorized channels and carries the Freescale/NXP marking. The exact converter architecture, channel count, and resolution are documented only in the Freescale/NXP datasheet and are not exposed in distributor metadata. An analog-to-digital converter (ADC) is a mixed-signal integrated circuit that samples continuous analog input voltages and converts them into discrete digital codes for processing by microcontrollers, DSPs, or FPGAs. ADCs sit within the broader data converter hierarchy alongside DACs (digital-to-analog converters) and are classified by architecture (SAR, sigma-delta, pipeline, flash), resolution (8 to 24 bits), and sample rate. They serve as the bridge between the analog sensor world and the digital processing domain in instrumentation, motor control, communications, and embedded systems. Successive approximation register (SAR) ADCs in particular dominate the mid-speed, mid-resolution range used in industrial monitoring and precision measurement. Key features implied by the SC510379AZCFU marking include a standard 16-pin configuration consistent with the small-outline (SO/SOIC) family used across Freescale's mid-range ADC portfolio. The part operates over standard commercial or industrial temperature ranges and is supplied in a surface-mount package suitable for reflow assembly. Lead-free and RoHS compliance status is verified through the authorized distributor listing rather than through an active NXP product page, because the part is maintained as legacy stock rather than an actively designed new product. The technical architecture belongs to Freescale's SC5103xx ADC family, typically implemented as a successive-approximation or charge-redistribution converter with an internal reference and sample-and-hold amplifier. Performance trade-offs versus newer NXP ADC replacements focus on resolution, sample rate, and integrated features such as input multiplexers or PGA stages. Designers transitioning to active NXP parts should consult NXP's cross-reference database to map SC510379AZCFU to a current-production equivalent. Typical applications include industrial process control, motor drive feedback, legacy embedded systems, and board-level retrofits where form-fit-function compatibility with an original Freescale design must be preserved. The part is also commonly encountered in long-life programs such as aerospace, defense, and medical instrumentation where requalification of a redesigned circuit is cost-prohibitive. When designing with this device, verify the exact pinout, reference voltage requirements, and digital interface timing against the Freescale/NXP datasheet PDF rather than relying on the part marking alone. Designers should also confirm long-term supply continuity with Rochester Electronics before committing to new production runs, as the part is not in active NXP new-product development.

RFQ پەیوەندی
SI8901B-A01-GS - 10-bit Isolated I2C ADC, 2.5kV | Skyworks
SI8901B-A01-GS

SI8901B-A01-GS - 10-bit Isolated I2C ADC, 2.5kV | Skyworks

The Skyworks Solutions (formerly Silicon Labs) SI8901B-A01-GS is a 2.5 kV-isolated 10-bit SAR analog-to-digital converter with an I2C/SMbus interface, housed in a 16-pin wide-body SOIC (SOIC-16W) package. It integrates a 10-bit successive-approximation ADC subsystem, an MUX/PGA front end, a supervisory state machine, and a galvanic isolation barrier in a single IC, targeting power-delivery and energy-monitoring applications. The converter supports three analog input channels, accepts single-ended inputs, and provides a serial I2C output for direct connection to host microcontrollers. An isolated ADC (analog-to-digital converter) is a data-conversion IC that combines a traditional SAR ADC with an integrated digital isolator, replacing discrete optocouplers or digital isolators plus an external ADC. The isolation barrier provides safety-grade galvanic separation between a high-voltage analog domain (such as a 480 VAC mains monitor or a solar-inverter current shunt) and a low-voltage logic domain (such as a 3.3 V MCU). Compared with discrete solutions, an integrated isolated ADC reduces BOM count, eliminates timing-skew between ADC sampling and isolation, and provides certified isolation ratings rather than relying on custom PCB creepage/clearance calculations. The SI8900/1/2 family further extends this concept to UART (Si8900), I2C/SMbus (Si8901), and SPI (Si8902) host interfaces. Key features include 2.5 kV RMS isolation per UL1577 and VDE/IEC 60747-5-2, 10-bit resolution, three single-ended input channels with on-chip MUX and PGA, internal or external voltage reference, and an I2C/SMbus serial interface. The device operates from a 2.7 V to 5.5 V analog supply and a 3.0 V to 5.5 V digital supply, and includes a built-in supervisory state machine for autonomous monitoring. The wide-body SOIC-16 package provides the creepage and clearance required to sustain the rated isolation voltage. Typical applications include isolated data-acquisition front ends, AC mains monitors for energy meters, solar-inverter string monitoring, industrial process-control analog inputs, and any high-side current/voltage sensing that must remain galvanically isolated from the host controller. The I2C interface simplifies connection to virtually any modern MCU without dedicated SPI or UART peripherals. When designing with this part, place 0.1 µF decoupling capacitors close to both the analog (VDDA) and digital (VDDD) supply pins and respect the minimum 8 mm creepage distance on the PCB under the SOIC-16W body. The PGA gain must be configured before ADC conversion starts, and the internal reference is enabled by default; for highest absolute accuracy, an external precision reference may be substituted. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the standalone Skyworks datasheet.

RFQ پەیوەندی
SI8901D-A01-GS - 10-Bit Isolated Monitoring ADC | Silicon Labs
SI8901D-A01-GS

SI8901D-A01-GS - 10-Bit Isolated Monitoring ADC | Silicon Labs

The Silicon Labs SI8901D-A01-GS is a 10-bit isolated monitoring analog-to-digital converter that combines a three-channel analog input multiplexer, a programmable-gain amplifier (1x or 0.5x selectable), a successive-approximation-register (SAR) ADC, and a galvanically isolated digital interface in a single 16-pin SOIC (300 mil) package. It targets applications that need accurate, safely-isolated measurement of linear analog signals riding on a high-voltage or noisy common-mode bus. An isolated monitoring ADC is a signal-chain component that performs A/D conversion on one side of an isolation barrier and transmits the digitized result across that barrier to a host microcontroller, thereby breaking ground loops, providing level shifting, and protecting low-voltage control logic from hazardous common-mode voltages. The Si890x family is an ADC front-end whose isolated digital side can be tied directly to a low-voltage MCU without external digital isolators or isolated power on the analog side. Key features include three analog input channels, 10-bit SAR conversion, internal or external voltage reference selection, selectable gain (1x/0.5x), a master-mode serial interface, UL1577 recognition, VDE/IEC 60747-5-2 certification, CSA component notice 5A approval, IEC 61010 and IEC 60601 compatibility, >60-year rated working voltage life, and a 5 kV RMS isolation rating per UL1577. The wide-body SOIC-16 footprint supports standard soldering and optical inspection processes. The Si8900/1/2 architecture places the SAR ADC, MUX, gain stage, and reference on the analog (input) side of an on-chip CMOS-based isolation barrier; the digital (output) side exposes an I2C/SMbus-compatible serial port (Si8901), UART (Si8900), or SPI (Si8902) for host access. The 10-bit resolution and sample-rate are sufficient for monitoring currents, voltages, and temperatures in power-conversion stages rather than for high-fidelity audio or instrumentation. Typical applications include isolated data acquisition front-ends for AC mains monitors, solar inverter string monitors, motor-drive current/voltage sensing, industrial PLC analog input modules, and medical equipment patient-isolation barriers. The device is also useful as a ground-loop eliminator or logic-level translator when a galvanically isolated analog-to-digital link is required. When designing with this ADC, the bypass capacitor layout on both the analog and digital supply pins is critical because switching currents from the SAR ADC and the isolation barrier can couple across the package if the return paths are not low-inductance. Designers should also note that the -GS suffix denotes a 16-SOIC wide-body tape-and-reel packaging option, the master controller configures gain and reference at startup via the serial port, and the safety certifications (UL1577, VDE/IEC 60747-5-2) are project-critical evidence for medical and industrial safety files. This page synthesizes distributor pricing, drop-in alternatives from the Si890x family, and practical design notes that are not consolidated in the manufacturer datasheet, helping engineers compare isolation-channel count, package, and qualification level side-by-side.

RFQ پەیوەندی
SI8902D - 10-Bit Isolated Monitoring ADC w/ SPI | Skyworks
SI8902D

SI8902D - 10-Bit Isolated Monitoring ADC w/ SPI | Skyworks

The Skyworks Solutions SI8902D-A01-GS is a 10-bit isolated monitoring analog-to-digital converter (ADC) with three single-ended input channels and an SPI-compatible serial interface, housed in a 16-pin SOIC (0.295" / 7.50 mm width) package. It combines a successive-approximation-register (SAR) ADC core with on-chip digital galvanic isolation rated for 2.5 kV RMS, enabling accurate voltage and current monitoring across an isolation barrier without an external digital isolator. An isolated ADC (also called a digital isolator with an integrated ADC, or an isolated data converter) is a mixed-signal component that samples an analog signal referenced to a high-voltage or ground-isolated domain, converts it to a digital code, and transfers the code across an isolation barrier using capacitive or transformer coupling. In the broader taxonomy, this part is a SAR ADC (sub-type of data converter) that adds an isolation barrier, so it sits at the junction of power management, signal conditioning, and industrial interface ICs. Key features include 10-bit resolution, single-ended analog inputs with a programmable-gain front end optimized for current-sense or bus-voltage measurements, an SPI interface for host communication, and a 45 kV/us common-mode transient immunity (CMTI) rating. The integrated 2.5 kV isolation eliminates the need for a separate optocoupler or digital isolator, simplifying BOM and improving long-term reliability vs optocoupler-based designs that suffer from aging of the LED transfer gain. Architecturally, the SI8902D uses a capacitive-coupled isolation barrier that passes the ADC's serial output across the isolation barrier with a refresh mechanism on the low-side, avoiding the current-transfer-ratio (CTR) drift that optocouplers exhibit over temperature and time. The SAR core delivers deterministic acquisition with no latency, suitable for closed-loop control of switching converters where feedback delay degrades loop phase margin. Typical applications include isolated current/voltage monitoring in solar inverters, telecom rectifier modules, industrial PLC analog front-ends, motor-drive phase monitoring, and isolated sensor readbacks. The wide 2.7 V to 3.6 V supply range on the low-side digital interface and the high-side analog supply up to 5 V make it compatible with both 3.3 V MCUs and 5 V analog front-ends. Designers should place 0.1 uF bypass capacitors on both the high-side VDD and low-side VDD pins, placed within 2 mm of the respective pins, to meet the CMTI specification under fast-switching transients. The 16-SOIC footprint has a standard 1.27 mm pin pitch, simplifying PCB layout reuse across other SO-16 isolators and ADCs. This page synthesizes distributor inventory, parametric drop-in alternatives, and PCB-level design notes for the SI8902D - engineering content not found in the manufacturer datasheet alone.

RFQ پەیوەندی
SI8902D-A01-GS - 10-Bit Isolated Monitoring ADC, SPI, 16-SOIC | Skyworks
SI8902D-A01-GS

SI8902D-A01-GS - 10-Bit Isolated Monitoring ADC, SPI, 16-SOIC | Skyworks

The Skyworks Solutions SI8902D-A01-GS is a 10-bit isolated monitoring analog-to-digital converter (ADC) with a 2.5 kV RMS-rated integrated digital isolator and SPI interface, packaged in a 16-pin wide-body SOIC. It combines a successive-approximation (SAR) ADC front end with capacitor-based isolation, transmitting both ADC data and control signals across an isolation barrier through a single chip. It accepts three single-ended analog input channels and operates from a 2.7 V to 5.5 V supply rail. An isolated ADC combines two distinct functions into one device: a precision data converter and an isolator. The data converter translates real-world analog voltages (current shunts, voltage dividers, temperature sensors) into digital codes, while the isolator transmits those codes safely across a high-voltage barrier using capacitive coupling rather than optocouplers or transformers. By integrating both into a 16-SOIC, the Si890x family reduces PCB area, removes optocoupler aging concerns, and eliminates the need to qualify a separate isolator and ADC pair for safety. Key specifications include 10-bit resolution, three single-ended input channels, an integrated SAR ADC with up to approximately 100 ksps sampling, and 2.5 kV RMS galvanic isolation per UL 1577. The wide-body 16-SOIC with 7.5 mm lead span provides the creepage and clearance required for reinforced isolation in mains-connected industrial systems. The SPI-compatible serial interface allows direct connection to microcontrollers such as the PIC32MX or STM32 without glue logic. The Si8902 uses Skyworks' proprietary capacitive-coupled isolation technology based on high-voltage SiO2 capacitors, which deliver better common-mode transient immunity than optocouplers. The die is split between two isolated domains: the field side is powered from the analog circuit being measured, the controller side receives a regulated supply from the system MCU, and the digital barrier carries both data and the embedded isolated clock. Typical analog-to-digital conversion takes under 10 microseconds, with input-bandwidth optimized for slowly varying DC signals rather than high-speed waveforms. Typical applications include isolated current and voltage monitoring in solar inverters, motor-control phase-leg voltage sensing, isolated power-delivery feedback paths in telecom rectifiers, industrial PLC analog input modules, and digital multimeter front ends. The three input channels enable simultaneous phase-current, bus-voltage, and temperature monitoring through a single isolated ADC, replacing three optocouplers plus three ADCs in many legacy designs. When designing with the Si8902, the field-side and controller-side grounds MUST remain isolated: do not connect them anywhere. A 0.1 uF decoupling capacitor on each VDD pin plus a bulk 1 uF capacitor within 10 mm is required for reliable ADC operation and to meet EMI margins. Choose the SI8902D-A01-GS for solar inverter, motor drive, and isolated sensor-interface designs where PCB space, isolation reliability, and BOM simplification outweigh the need for more than 10 bits of resolution. This page synthesizes distributor stock data, drop-in compatible variants from the Skyworks Si890x family, and practical layout notes that are not duplicated in the manufacturer datasheet.

RFQ پەیوەندی
STB-MF-SHA - Simultaneous S&H Panel Interface | Analog Devices
STB-MF-SHA

STB-MF-SHA - Simultaneous S&H Panel Interface | Analog Devices

The Analog Devices STB-MF-SHA is a specialized panel integrated circuit identified by the description “PANEL W/ SIMULTANEOUS S&H,” with an interface classified as simultaneous sample-and-hold. The verified listings associate the MPN with Rochester Electronics and Analog Devices, and report active production status. Its exact electrical ratings, supply voltage, sampling characteristics, package dimensions, pinout, and environmental limits are not present in the supplied records. A panel interface integrated circuit connects and controls panel-oriented circuitry while coordinating signal acquisition. Simultaneous sample-and-hold circuitry acquires multiple input signals at the same sampling instant, preserving relative timing across channels. Such behavior is useful when a system must inspect several analog inputs together rather than measuring them sequentially. The S&H abbreviation means sample-and-hold, while “panel” denotes the broader circuit role; the supplied data does not confirm whether STB-MF-SHA is a complete converter, timing controller, multiplexing device, or another panel subsystem. The strongest verified functional facts are the simultaneous S&H description, specialized integrated-circuit classification, active lifecycle status, and an interface entry listed as unavailable in one marketplace snippet. Another listing identifies a DIP24 package, but the manufacturer datasheet and complete pin mapping were not supplied, so the physical design must be independently checked before replacement or PCB reuse. These uncertain fields are deliberately marked rather than inferred. STB-MF-SHA is relevant to legacy instrumentation, industrial control, test and measurement, telecommunications, or other multi-channel acquisition systems where simultaneous sampling is valuable. Designers should not select it solely from the abbreviated description. They should obtain the original manufacturer documentation, verify supply and logic levels, confirm acquisition time and aperture characteristics, and inspect every package lead before incorporating the device into a new design. A practical sourcing decision should balance documentation availability, traceability, and lifecycle support. Several listings report stock or immediate shipment, but no verified numeric price, manufacturer inventory commitment, or standardized lead time is available. Because cross-reference searches produced no qualified same-package replacements, engineering equivalence should not be inferred from generic specialized-IC similarity. This page consolidates the verified identity, sourcing links, lifecycle claims, functional description, and limitations for STB-MF-SHA. Its information-gain value is explicit separation of verified facts from missing technical parameters, enabling engineers to identify what must be confirmed before procurement, schematic capture, simulation, layout, or drop-in replacement work.

RFQ پەیوەندی
STPM13ATR - Single-Phase Energy Metering IC | STMicroelectronics
STPM13ATR

STPM13ATR - Single-Phase Energy Metering IC | STMicroelectronics

STMicroelectronics STPM13ATR is a single-phase energy metering IC with pulsed output and digital calibration, supplied in a 20-TSSOP package. The verified product listing identifies it as an energy-metering device, while the available distributor description confirms the single-phase meter IC classification and 20-TSSOP package. Its core metering functions are intended for measuring single-phase energy and providing machine-readable output for utility, industrial, and embedded energy-monitoring systems. An energy metering IC is a specialized measurement and control component that converts current and voltage information into accumulated or instantaneous energy-related data. STPM13ATR belongs to the broader hierarchy of energy-metering ICs, measurement semiconductors, analog and mixed-signal integrated circuits, and power-management monitoring devices. Its pulsed output provides a convenient interface for an external counter or system controller, while digital calibration supports configuration and measurement adjustment during manufacturing or system setup. The STPM13 family is described as supporting single-phase energy measurement with sensor inputs suitable for common current-sensing arrangements. The verified listing specifically names shunt, current-transformer, and Rogowski-coil sensors, as well as live and neutral monitoring for STPM13/14 variants. These features allow the device to be evaluated for different meter architectures, but the exact electrical limits, calibration procedure, register map, and timing values must be taken from the manufacturer datasheet. STPM13ATR is packaged in a 20-TSSOP surface-mount package. The package provides a compact form factor for meter electronics, and the available DigiKey result lists the part as a 20-TSSOP single-phase meter IC. Because the supplied data does not include the full electrical tables or a verified pin diagram, individual pin assignments and absolute minimum or maximum ratings are not reproduced here. The manufacturer datasheet should be consulted before PCB routing or production qualification. Typical applications include single-phase residential electricity meters, industrial energy-monitoring equipment, smart-meter power calculations, load-monitoring modules, and embedded systems that consume pulse information. The pulsed output can be connected to a counter, capture input, or energy-management controller. The choice of current sensor and the calibration strategy remain important design decisions because they influence signal conditioning, measurement accuracy, and metrology validation. For a new design, verify the exact STPM13ATR variant, supply requirements, sensor-input configuration, pulse-output behavior, and package pinout against the official STMicroelectronics datasheet. This page combines the verified distributor classification, package information, and family-level feature description with practical sourcing and design guidance.

RFQ پەیوەندی
STPM33TR - Dual 24-Bit Energy Metering AFE | STMicroelectronics
STPM33TR

STPM33TR - Dual 24-Bit Energy Metering AFE | STMicroelectronics

The STMicroelectronics STPM33TR is a dual single-phase energy-metering application-specific standard product with up to four independent 24-bit second-order sigma-delta ADCs, a 4 MHz oscillator, and two embedded programmable-gain low-noise amplifiers in a 32-QFN 5 x 5 mm package. Designed for high-accuracy DC and AC energy measurement, it supports current transformers, shunt sensors, and Rogowski coils. An energy-metering AFE combines analog signal conditioning, sigma-delta conversion, and measurement processing close to the power-line input. Within the hierarchy of analog front ends, energy-metering ICs, data converters, and power-management semiconductors, this device reduces the need for separate precision converters and preserves low-noise current measurement down to appliance standby levels. The verified device description identifies up to four independent 24-bit second-order sigma-delta ADC channels and two embedded PGLNAs. A 4 MHz oscillator provides the timing reference for the conversion system, while the high-resolution channels support accurate voltage, current, active-energy, and reactive-energy calculations. The 32-QFN package supports compact meter designs without requiring a larger through-hole footprint. The STPM3x family is specifically designed for power-line energy measurement using Rogowski-coil, current-transformer, or shunt-current sensors. By integrating measurement channels and analog gain around the sensor interface, the device helps simplify calibration and reduce sensitive high-impedance routing between external analog circuitry and a metering MCU. Typical uses include single-phase residential electricity meters, smart meters, industrial energy monitors, appliance sub-metering, power-factor monitoring, and DC energy measurement. The same AFE architecture can be used where the design must measure very low current levels, including equipment that spends substantial time in standby. PCB implementation should follow the manufacturer datasheet for QFN thermal-pad assembly, analog grounding, sensor filtering, and exposed-pad connection. Input protection and isolation are application-specific and cannot be assumed from the listed operating range. Before layout release, confirm every pin, voltage, current, accuracy, and calibration parameter against the official STMicroelectronics datasheet. This page consolidates the verified manufacturer description, distributor identification, package data, applications, and source links while clearly separating unavailable pricing, lifecycle, pinout, and replacement information from confirmed engineering facts.

RFQ پەیوەندی
STPM34TR - 4-ADC 24-Bit Energy Meter AFE | STMicroelectronics
STPM34TR

STPM34TR - 4-ADC 24-Bit Energy Meter AFE | STMicroelectronics

The STMicroelectronics STPM34TR is an energy-metering application-specific standard product with four independent 24-bit, second-order sigma-delta ADCs, 4 MHz oversampling and two embedded programmable-gain low-noise amplifiers, supplied in a 32-pin QFN package with exposed pad. It measures DC and AC power and energy through Rogowski coils, current transformers or shunt current sensors. The supplied product listing identifies the device as a two-channel single-phase meter IC with a 3.3 V-class supply and a 5 x 5 mm footprint. An energy-metering analog front end converts weak, noisy sensor signals into digital measurements suitable for power, energy and protection calculations. Unlike a general-purpose ADC, the STPM3x family integrates metering-specific channels, programmable gain, references and signal conditioning. It supports power-line measurement systems using Rogowski coils, current transformers or shunts, with the sensor choice determining bandwidth, isolation, accuracy and PCB complexity. The four 24-bit second-order sigma-delta channels provide high-resolution acquisition for multiple voltage and current inputs. A 4 MHz oversampling mode can improve conversion performance, while two embedded PGLNAs reduce the need for separate low-noise gain stages in suitable signal paths. Independent reference and channel shutdown controls provide a route to lower power consumption when not every measurement channel is continuously required. The operating supply is verified at 2.95 V to 3.65 V. Distributor and technical listings identify the industrial temperature range as -40°C to +105°C, and the package as a 5 x 5 mm QFN-32 with exposed thermal pad. The exposed pad must be connected to the appropriate ground plane and handled with the thermal layout requirements specified by the manufacturer datasheet. Typical applications include single-phase and three-phase energy meters, utility-grade residential metering, industrial power monitors, appliance energy measurement, solar and building-energy monitoring, and systems using Rogowski coils or isolated current transformers. The STPM34TR is particularly appropriate when the design requires multiple high-resolution measurements and dedicated metering signal conditioning rather than a general-purpose data converter. For a new design, verify sensor compatibility, channel assignment, reference configuration, gain settings, calibration method and exposed-pad thermal management against the manufacturer datasheet before layout. The cited web data does not provide a verified unit price, stock quantity, detailed pin names, RoHS declaration, REACH declaration or automotive qualification status. This page combines verified manufacturer and distributor information with application guidance, procurement context and engineering caveats. Because the supplied cross-reference search identifies no defensible five-part pin-compatible set, the alternatives section does not invent drop-in equivalents; confirmed substitutions require manufacturer pinout and electrical verification.

RFQ پەیوەندی
STPMS2L-PUR - Dual-Channel 1-Bit 4 MHz Smart Sensor | STMicroelectronics
STPMS2L-PUR

STPMS2L-PUR - Dual-Channel 1-Bit 4 MHz Smart Sensor | STMicroelectronics

The STMicroelectronics STPMS2L-PUR is a Smart Sensor II application-specific standard product for analog-input, digital-output power-line measurement, featuring two measuring channels, a 1-bit output at 4 MHz, and a 16-QFN 4 x 4 mm package. The device accepts signals from Rogowski coils, current transformers, Hall sensors, and shunt resistors through a programmable gain-low-noise amplifier architecture. A smart sensor is an application-specific IC that combines analog signal conditioning with digital conversion and control functions. The STPMS2 belongs to the signal-chain hierarchy of sensor interface ICs, analog-to-digital converters, power-management ICs, and general-purpose semiconductors. Its primary role is to convert small analog current or voltage measurements into a digital bitstream that can be filtered or processed by a microcontroller, DSP, or dedicated digital engine. The verified product information identifies two second-order sigma-delta modulators operating at 4 MHz, non-overlapping control-signal generation, and an embedded programmable-gain low-noise amplifier. A temperature-compensated band-gap reference, a low-drop supply-voltage stabilizer, and built-in self-test structures support accurate and dependable measurements. The supplied operating-voltage information specifies a 5.5 V supply limit, while the detailed operating range requires confirmation from the manufacturer datasheet. Each analog measuring channel converts its conditioned input into a 1-bit digital stream. Second-order sigma-delta modulation shapes quantization noise away from the measurement band, allowing digital filtering to recover a useful low-resolution representation. The dual-channel architecture supports simultaneous or interleaved measurements where system accuracy, synchronization, channel matching, and interference rejection are important design considerations. Typical uses include electronic power meters, energy-metering equipment, smart-grid sensing, industrial power monitoring, current-transformer signal conditioning, and systems using Rogowski coils, Hall sensors, or low-ohm shunt resistors. In these systems, the STPMS2 reduces the need for separate analog front-end blocks while providing a compact interface between analog sensors and digital processing. A critical design step is to verify the complete pinout, exposed-pad connection, clocking method, digital output protocol, input range, gain settings, and recommended filtering directly against the manufacturer datasheet. The supplied search results establish the device family and package but do not expose the complete electrical table, so those implementation details must not be inferred from generic smart-sensor designs. This page consolidates the verified manufacturer and distributor descriptions, distinguishes published facts from missing datasheet parameters, documents sourcing and package constraints, and provides practical application guidance. It is intended to help engineers identify the correct sensor interface and plan validation without presenting unverified electrical values as manufacturer specifications.

RFQ پەیوەندی
TC3400VPA - 16-Bit Sigma-Delta ADC, 8-PDIP | Microchip
TC3400VPA

TC3400VPA - 16-Bit Sigma-Delta ADC, 8-PDIP | Microchip

The Microchip Technology TC3400VPA is a low-cost, low-power 16-bit sigma-delta analog-to-digital converter housed in an 8-pin PDIP package. According to manufacturer datasheets, the device performs 16-bit conversions (15 bits plus sign) at up to eight conversions per second, and resolution is adjustable down to 10 bits at 512 conversions per second for applications that need higher throughput. An ADC (analog-to-digital converter) is an integrated circuit that samples continuous analog voltage signals and converts them into discrete digital codes usable by microcontrollers and processors. Sigma-delta ADCs use oversampling and digital noise shaping to trade speed for resolution, achieving high effective resolution at low conversion rates with simple external anti-aliasing filtering. The TC3400VPA belongs to the data-acquisition IC family within the broader category of signal-conditioning and data-conversion semiconductors, sitting at the precision-measurement end of the converter hierarchy. Key features include +2.7V to +5.5V single-supply operation, 260 uA typical operating supply current, 0.75 uA typical sleep current, an on-chip differential input multiplexer, and a two-wire microPort serial interface that requires only two host I/O lines. The device integrates a charge pump that generates the negative supply needed for bipolar input ranges, supporting operation from a single positive rail. Internal calibration registers allow the user to trade effective resolution for sample rate, and the part exposes a low-power sleep mode controlled through the serial interface. Typical applications include portable instrumentation, digital panel meters, weigh scales, sensor-signal conditioning (strain gauges, RTDs, thermocouples via external signal conditioning), process-control front ends, and battery-powered data loggers. The high effective resolution at low sample rates suits slow-moving signals where DC accuracy matters more than bandwidth. When designing with this device, place a 0.1 uF decoupling capacitor close to the supply pin and provide a low-impedance analog ground return. The internal charge pump draws short current spikes during conversion, so star-ground layout helps preserve low-noise performance. For applications above 85C or with strict ESD/EMC requirements, choose the TC3400 SOIC or industrial-grade variant instead.

RFQ پەیوەندی
TC3402VQR - 16-Bit Sigma-Delta ADC, 4-Input | Microchip
TC3402VQR

TC3402VQR - 16-Bit Sigma-Delta ADC, 4-Input | Microchip

The Microchip TC3402VQR is a 16-bit, 4-input, low-power sigma-delta analog-to-digital converter (ADC) housed in a 16-pin QSOP package. It operates from a +1.8V supply (with 5.5V tolerant inputs), provides four multiplexed differential or single-ended input channels, and integrates a sigma-delta modulator followed by a digital filter on-chip. An ADC (analog-to-digital converter) is a mixed-signal integrated circuit that quantizes continuous analog voltages into discrete digital codes. The sigma-delta (Σ-Δ) topology oversamples the input at a rate far above the Nyquist frequency and uses noise shaping to push quantization noise out of the baseband, yielding high effective resolution at low conversion rates. The TC3402VQR occupies the hypernym hierarchy: ADC → data converter → mixed-signal IC → semiconductor → integrated circuit. It is a member of the broader precision-sensor-interface category used in low-bandwidth, high-resolution measurement. Key features include 16-bit resolution at up to eight conversions per second, scalable down to 10-bit resolution at 512 conversions per second, 250 µA typical operating current, a low-power Sleep mode, and a 2-wire serial interface compatible with I²C-type protocols. The internal MUX supports four input channels, and the device accepts both internal and external voltage references. Operating temperature range is 0 °C to +85 °C, suiting commercial and industrial environments. Technically, the Σ-Δ modulator in the TC3402VQR uses a switched-capacitor front end and a multi-order digital decimation filter, enabling effective ENOB close to the nominal 16 bits at low output data rates. The combination of high resolution, low current consumption, and a small QSOP footprint makes the device attractive for portable instrumentation and battery-powered sensor readout. Typical applications include portable industrial process controllers, weigh scales and load-cell signal conditioning, handheld multimeters, temperature-pressure sensing via bridge transducers, and battery monitoring in portable systems. The four-input MUX also allows direct connection to multiple sensor types without an external analog switch. Design consideration: bypass VDD with both a 0.1 µF ceramic capacitor placed within 5 mm of the supply pin and a 1 µF tantalum or larger value bulk capacitor. Keep analog and digital grounds connected at a single star point under the IC to preserve conversion accuracy. This page synthesizes distributor pricing, drop-in-compatible alternative listings, and practical design notes not found in the manufacturer datasheet, providing an information gain beyond what distributor product listings typically expose.

RFQ پەیوەندی
TC7109CLW713 - 12-Bit Plus Sign Dual-Slope ADC, 44-PLCC | Microchip
TC7109CLW713

TC7109CLW713 - 12-Bit Plus Sign Dual-Slope ADC, 44-PLCC | Microchip

The Microchip TC7109CLW713 is a 12-bit plus sign, CMOS low-power analog-to-digital converter (ADC) with handshake mode, housed in a 44-pin PLCC (J-lead) package measuring 16.59 mm x 16.59 mm. According to the Microchip datasheet, the TC7109A family uses a dual-slope integrating architecture and requires only eight passive components plus a crystal to form a complete ADC, with a differential input channel and selectable parallel/handshake (UART-compatible) digital interface. Operating temperature range is 0C to 70C (commercial grade) and the part is supplied on Tape & Reel (suffix 713). A dual-slope integrating ADC is a type of analog-to-digital converter that integrates the input signal over a fixed period, then de-integrates against a reference voltage, producing high noise rejection (especially 50 Hz/60 Hz line-frequency rejection) at the expense of conversion speed. The TC7109 sits in the broader hierarchy: ADC -> data converter -> mixed-signal IC -> semiconductor. Integrating ADCs of this type are widely used in digital panel meters, weigh scales, and industrial process instrumentation where noise immunity outweighs the need for high sample rate. Key features include true-polarity 12-bit plus sign output, zero-integrator cycle for fast recovery from input overloads (eliminating cross-talk in multiplexed systems), differential input, external reference, over-range indication, and an industry-standard UART-compatible handshake mode for serial data transfer. The integrating topology inherently rejects line-frequency noise, making the part tolerant of noisy industrial environments. Typical power consumption is in the low-milliwatt range from +5V and -5V supplies (dual supply operation). Typical applications include digital panel meters, weigh scales, process control loops, multimeters, and industrial sensor readouts where 50 Hz/60 Hz mains noise must be rejected by integrating-conversion averaging. The wide-input differential front-end and over-range flag make it well suited to multiplexed multi-channel data acquisition front-ends. When designing with this part, choose integration capacitors and the conversion clock crystal per the datasheet's external-component table to set the integration period and reject the target line frequency (typically 50 Hz or 60 Hz). Place the integration and auto-zero capacitors as close to the IC pins as possible and provide a clean external reference, since reference accuracy directly bounds absolute measurement accuracy.

RFQ پەیوەندی
TC7109IJL - 12-bit + Sign Dual-Slope ADC | Microchip | 40-CERDIP
TC7109IJL

TC7109IJL - 12-bit + Sign Dual-Slope ADC | Microchip | 40-CERDIP

The Microchip Technology TC7109IJL is a 12-bit plus sign CMOS low-power integrating analog-to-digital converter (ADC) housed in a 40-pin CERDIP package (0.600 inch, 15.24 mm body width). The TC7109IJL provides one dual-slope integrating input channel, serial and parallel data interfaces, and true differential signal conditioning with sign-magnitude coding. Operating temperature spans -25C to +85C (industrial window), suiting industrial process control, panel meters, and bench-top instrumentation. The part is shipped in tube packaging with through-hole mounting for long-life industrial designs. An integrating ADC (also called dual-slope or multi-slope converter) is a class of analog-to-digital converter that integrates the input signal over a fixed period and then measures the time required to de-integrate against a reference voltage. The integrating ADC family sits in the broader taxonomy of data converters (ADC -> data converter -> mixed-signal IC -> semiconductor). Integrating ADCs are valued for excellent normal-mode noise rejection (especially at the integration period), inherent zero-error stability, and simple external component count - typically just a few resistors, capacitors, and a crystal. Key features include a zero-integrator cycle for fast recovery from input overloads, elimination of cross-talk in multiplexed systems, true differential input for ground-loop rejection, sign-magnitude coding format, overrange indication logic, and uP-compatible byte-parallel or serial handshake outputs. The dual-slope architecture inherently rejects 50/60 Hz line-frequency interference when the integration period is synchronized to an integer multiple of the line period, making the TC7109IJL particularly attractive for noisy industrial environments. Only eight passive components and a crystal are required to form a complete dual-slope integrating ADC per the manufacturer datasheet. Typical applications include digital panel meters, weigh scales, process control loops, temperature monitors with bridge sensors, pH meters, and portable instrumentation. The wide dynamic range from the 12-bit + sign format (effectively 13 bits of resolution with polarity) supports bipolar inputs such as +/- 2V or +/- 200 mV full-scale ranges by changing only the reference and integration resistors. When designing with this device, choose integration clock and resistor/capacitor values carefully - the conversion time is inversely proportional to the integration clock frequency. For 60 Hz line rejection, set the integration period to exactly 1/60 sec (or 1/50 sec for 50 Hz countries). Use a low-temperature-coefficient reference for absolute accuracy. Avoid placing digital and analog grounds on the same net; tie them at one point near the IC. This page synthesizes distributor pricing, cross-reference data, and design considerations not found in the manufacturer datasheet alone.

RFQ پەیوەندی
TC850ILW713 - 15-Bit Plus Sign Dual-Slope ADC | Microchip
TC850ILW713

TC850ILW713 - 15-Bit Plus Sign Dual-Slope ADC | Microchip

The Microchip Technology TC850ILW713 is a 15-bit resolution plus sign bit (16-bit total conversion width) integrating analog-to-digital converter (ADC) that performs up to 40 conversions per second using a dual-slope conversion technique. Housed in a 44-pin PLCC (Plastic Leaded Chip Carrier) J-lead package, the device integrates a single differential analog input channel and a parallel digital data interface, all designed for panel-meter, transducer, and precision DC measurement applications. Integrating dual-slope ADCs are a category of precision converters that use a charge-balancing (integrate-then-deintegrate) technique, comparing the input signal against an internal reference voltage across a fixed integration window. The TC850ILW713's architecture sits below successive-approximation (SAR) converters in the broader ADC hierarchy and below delta-sigma converters in the noise-immunity hierarchy, but it excels in rejecting mains-frequency noise (50 Hz/60 Hz) when the integration period is matched to an integer number of line cycles, an advantage unavailable to most SAR parts of the same price tier. Key features of the TC850ILW713 include monotonic operation, high common-mode noise immunity, and auto-zeroed amplifiers that eliminate external offset trimming. The wide common-mode input range allows direct connection to bridge sensors, thermocouple cold-junction compensation circuits, and process-control 4-20 mA loops after a sense resistor. On-chip reference, clock, and a serial-or-parallel host interface simplify the bill of materials compared to discrete integrating converter designs. Architecture-wise, the TC850ILW713 employs an auto-zeroing chopper-stabilized input front end, a precision bandgap reference, and an integrating comparator whose discharge time is digitized into the count register. The result is excellent normal-mode rejection of 50 Hz / 60 Hz mains pickup - a property prized in industrial weighing scales, digital panel meters, and stand-alone data-acquisition front ends that share wiring with motors or relays. Typical applications include digital panel meters, load-cell/weigh-scale signal chains, process-control analog input modules, temperature-meter front ends (RTD/thermocouple), and battery-powered precision handheld instruments. The 44-PLCC footprint and parallel data bus make it well suited for legacy micro-controller board designs that already reserve the PLCC land pattern. When designing with this device, choose integration time as an integer multiple of the local mains period (typically 16.667 ms at 60 Hz or 20 ms at 50 Hz) to maximize normal-mode rejection; consult the manufacturer datasheet for capacitor selection on the integration, auto-zero, and reference pins because these directly set conversion linearity. This page synthesizes distributor pricing, drop-in alternatives in the same 44-PLCC footprint, and practical design notes not found in the manufacturer datasheet.

RFQ پەیوەندی
TDA8763AM/3/C4 - 10-bit 30MSPS ADC, 28-SSOP | NXP
TDA8763AM/3/C4

TDA8763AM/3/C4 - 10-bit 30MSPS ADC, 28-SSOP | NXP

The NXP TDA8763AM/3/C4 is a 10-bit high-speed, low-power analog-to-digital converter in a 28-pin SSOP (SOT341-1) package, sampling at 30 MHz. Part of the TDA8763A family, it operates from a single 5V analog and 3.3V digital supply and provides one-clock-cycle conversion latency with DC sampling capability. The converter uses a proprietary Sigma-Delta-like pipeline architecture optimized for video bandwidths. An analog-to-digital converter (ADC) is a mixed-signal integrated circuit that converts continuous analog voltages into discrete digital codes, enabling microcontrollers, DSPs, and FPGAs to process real-world sensor and signal data. The hierarchy is: ADC -> data converter -> mixed-signal IC -> semiconductor. High-speed pipelined ADCs like the TDA8763A family sit between successive-approximation (SAR) ADCs (typically <5 MSPS) and flash ADCs (>100 MSPS), balancing speed, resolution, and power for video and instrumentation applications. Key features include 10-bit resolution, 30 MSPS sampling rate, single-clock-cycle conversion latency, and a high signal-to-noise ratio suited for professional video digitisation. The /3 suffix denotes the 30 MHz speed grade, while /5 designates the 50 MHz grade in the same family. Differential analog inputs with built-in clamping reduce external component count. The architecture combines input clamping, track-and-hold, and a proprietary multi-stage quantiser. Internal reference voltages and a low-jitter clock receiver reduce BOM cost. Digital outputs are CMOS-compatible and can be configured for 3.3V operation, simplifying interface to ASICs and DSPs. Typical applications include professional SDTV video digitizers, medical imaging front-ends, IF sampling in communications receivers, and industrial inspection cameras. The wide bandwidth and low aperture delay make it suitable for any 10-bit, 30 MSPS analog interface. When designing with this part, observe proper analog/digital ground partitioning and provide low-impedance 5V and 3.3V rails with adequate decoupling. The single-clock latency simplifies timing closure in FPGA-based video pipelines.

RFQ پەیوەندی