ADC/DAC
بەرهەمەکان (3,600+)
TLV1572ID - 10-Bit 1.25 MSPS Low-Power SAR ADC | TI
Texas Instruments TLV1572ID is a 10-bit, 1.25 MSPS, single-channel successive-approximation analog-to-digital converter designed for low-power data-acquisition systems. It operates from a single 2.7 V to 5.5 V supply, accepts an analog input from 0 V to VCC, and is housed in an 8-pin SOIC package. The converter provides 1 input channel, differential nonlinearity below ±1 LSB, integral nonlinearity below ±1 LSB, and 59 dB signal-to-noise and distortion ratio at a 500 kHz input frequency. A SAR ADC is a sampling data-converter category that compares the sampled input voltage against an internal DAC through a sequence of binary decisions. Unlike a flash or pipeline ADC, the SAR architecture generally requires less power while providing predictable conversion behavior. The TLV1572ID belongs to the broader ADC, data-converter, signal-processing IC, and semiconductor hierarchies, making it appropriate for embedded measurement, control, and industrial data-acquisition equipment. The principal performance features are the 1.25 MSPS maximum sampling rate, 10-bit resolution, single-ended input architecture, SPI-compatible serial interface, and automatic power-down capability. According to the manufacturer information, typical power consumption is 8 mW at a 3 V supply and 25 mW at a 5 V supply. These characteristics suit systems that need moderate conversion speed and compact implementation without the power and cost of a high-speed flash ADC. The TLV1572ID combines a sampling-and-hold input stage, internal 10-bit DAC, comparator, control logic, and serial output interface in an 8-pin SOIC. Automatic power-down helps reduce consumption when conversions are infrequent. The 59 dB SNR and distortion figure at 500 kHz provides a useful basis for evaluating signal-chain performance, while the stated DNL and INL limits characterize unipolar conversion linearity. Typical applications include industrial process monitoring, sensor signal acquisition, portable instrumentation, embedded control systems, battery-powered measurement equipment, and low-speed data loggers. Its single 2.7 V to 5.5 V supply range also allows it to operate directly from common 3 V and 5 V system rails. The 1.25 MSPS throughput provides sufficient speed for many control-loop and waveform-sampling tasks. Designers should verify the input range, reference behavior, digital-interface timing, and acquisition requirements against the manufacturer datasheet before finalizing a PCB. Input-source impedance, source settling, sampling capacitance, clock jitter, and digital return paths can materially affect practical conversion accuracy. Automatic power-down should also be accounted for when calculating wake-up latency and acquisition-cycle timing. This page consolidates verified manufacturer and distributor information, drop-in candidate analysis, application guidance, and design notes. It highlights the TLV1572ID's low-power SAR architecture and 1.25 MSPS throughput while clearly identifying the electrical details that still require datasheet confirmation.
TLV2541ID - 12-Bit 200 kSPS SAR ADC | Texas Instruments
Texas Instruments TLV2541ID is a 12-bit, 200 kSPS, single-channel successive-approximation ADC with serial output, SPI/DSP-compatible signaling, and operation from 2.7 V to 5.5 V in an 8-pin SOIC package. Its built-in conversion clock, automatic power-down capability, and TMS320-compatible interface support compact, low-power measurement systems. An ADC is an integrated circuit that converts an analog voltage into a digital code. The TLV2541 belongs to the successive-approximation ADC hierarchy, commonly abbreviated SAR ADC, and ultimately falls under data-converter and mixed-signal semiconductor categories. SAR converters are especially useful when moderate resolution, predictable conversion behavior, and a simple serial interface are more important than the very high throughput of a flash converter. Three principal specifications define the TLV2541: 12-bit resolution, a maximum conversion rate of 200 kSPS, and a single 2.7 V to 5.5 V supply. The converter also provides an integrated conversion clock. Verified performance data includes integral nonlinearity and differential nonlinearity of no more than ±1 LSB, signal-to-noise-and-distortion ratio of 72 dB, and spurious-free dynamic range of 85 dB at 20 kHz. The device uses a serial output architecture suitable for SPI-compatible and DSP-compatible signal processing. The interface is compatible with TMS320-class processors operating up to 10 MHz according to the manufacturer product description. Serial output reduces the number of signal lines required on a mixed-signal circuit board while allowing the converter to communicate directly with a microcontroller, digital signal processor, or serial communications controller. Typical uses include battery-powered industrial sensing, portable instrumentation, process-control measurement, low-speed data acquisition, and embedded systems that require analog monitoring without a parallel ADC bus. Its single-channel architecture is appropriate where one analog quantity must be sampled repeatedly. For multichannel systems, several converters can be used with analog multiplexing, provided settling time and acquisition requirements are reviewed carefully. The primary design consideration is ensuring that the analog input remains within the converter's valid range and that the serial interface timing matches the host processor. Decoupling, grounding, input-source impedance, and acquisition-time requirements should be evaluated against the manufacturer datasheet. Automatic power-down can reduce system consumption, but repeated wake-up intervals may affect effective sampling throughput. This page consolidates verified manufacturer and distributor information, drop-in same-family options, technical comparisons, and practical design guidance so engineers can assess the TLV2541ID without relying only on a distributor parameter table.
TLV2542ID - 12-Bit 200kSPS Dual SAR ADC | Texas Instruments
The Texas Instruments TLV2542ID is a 12-bit, 200 kSPS, dual-channel successive-approximation register analog-to-digital converter in an 8-pin SOIC package. It operates from a single 2.7 V to 5.5 V supply and provides serial output that is compatible with SPI and DSP interfaces operating up to 10 MHz. The device combines two analog input channels with a built-in conversion clock, chip select, serial clock, and serial data output for compact embedded measurement systems. An ADC is an analog-to-digital converter, a data-conversion IC that samples a continuously varying voltage and produces a corresponding numeric code. A successive-approximation-register, or SAR, ADC determines each conversion result through a sequence of internal comparisons. SAR ADCs are commonly used where predictable sampling, moderate resolution, low power, and compact serial interfaces are more important than very high conversion throughput. The TLV2542 belongs to the broader ADC data-converter and signal-processing semiconductor hierarchy. The TLV2542ID features 12-bit resolution, 140 kSPS or 200 kSPS maximum throughput options, and specified integral nonlinearity and differential nonlinearity of ±1 LSB maximum. Its signal-to-noise-plus-distortion ratio is specified at 72 dB, while the spurious-free dynamic range is 85 dB. The serial interface supports direct connection to microcontrollers, DSPs, and TMS320-compatible systems up to 10 MHz, reducing the need for external interface logic. The converter uses a single analog supply, with analog input and digital interface functions integrated into a small package. Automatic power-down helps reduce consumption when conversions are not continuously required. The dual-channel architecture is useful for monitoring two independent signals, while the 12-bit code provides approximately 4096 digital levels for each channel. Exact input-range, reference, and absolute-input details must be confirmed in the manufacturer datasheet before final design release. Typical applications include industrial process measurement, battery and power-system monitoring, portable instrumentation, sensor signal acquisition, and embedded DSP or MCU data logging. The serial interface reduces pin count compared with many parallel ADCs, while the dual input count allows one converter to serve two measurements. Designers should account for source impedance, sampling dynamics, reference accuracy, analog grounding, and serial-interface timing. A key implementation consideration is the relationship between analog signal conditioning and ADC accuracy. The front-end should present a low-impedance source, provide suitable filtering for the measurement bandwidth, and keep analog routing away from noisy digital clock and switching signals. This page combines verified product information, distributor availability, application guidance, and replacement constraints for practical engineering review.
TLV2543CN - 12-Bit 11-Channel 66 kSPS ADC | Texas Instruments
The Texas Instruments TLV2543CN is a 12-bit, 11-channel, successive-approximation analog-to-digital converter with a 66 kSPS conversion rate, serial output, programmable power-down, MSB/LSB-first data transfer, and built-in self-test in a 20-pin PDIP package. The converter uses switched-capacitor, successive-approximation conversion and provides an inherent sample-and-hold function. Its 10 µs conversion time and 11-channel multiplexing make it suitable for compact industrial measurement systems that need several analog inputs without allocating a separate converter to every signal. An analog-to-digital converter is an ADC, a mixed-signal semiconductor that converts a continuously varying analog voltage into a numeric code for processing, measurement, logging, or control. The TLV2543 belongs to the successive-approximation ADC family and the broader data-converter and signal-processing IC hierarchy. Its 12-bit resolution provides 4,096 quantization levels, while its serial interface reduces the number of signal lines required when compared with a parallel-output ADC. The headline capabilities include 12-bit resolution, an 11-channel analog input multiplexer, and a maximum throughput of 66 kSPS. The device supports both MSB-first and LSB-first serial output formats, giving the host controller flexibility in clocking and data processing. Programmable power-down helps reduce consumption when measurements are intermittent, while three built-in self-test modes support diagnostic checks of the converter and its serial interface. Internally, the switched-capacitor SAR architecture compares the sampled input against a generated reference during successive conversion steps. An inherent sample-and-hold stage isolates the selected input during conversion, while the 11-to-1 multiplexer allows one converter core to service multiple analog sources. The manufacturer identifies the device as a 1 SAR ADC with 11 input channels and a serial control/data interface. Typical uses include industrial process monitoring, environmental sensing, instrumentation, laboratory measurement, and embedded control systems. An ADC can be used when the system must repeatedly select one of several sensors, convert the selected voltage, and transfer the resulting code over a compact serial bus. The TLV2543CN is particularly relevant where 12-bit resolution is sufficient but the number of available pins or PCB area is constrained. Designers should confirm the actual reference voltage, analog input range, acquisition timing, digital interface levels, and operating-temperature limits against the manufacturer datasheet before layout. Because this part is a multiplexed converter, source impedance, sampling charge, settling time, and protection-network capacitance can affect conversion accuracy. Decouple the supply and reference rails locally, keep analog routing away from fast digital signals, and account for the 10 µs conversion time when scheduling scans. This page consolidates the verified 12-bit, 66 kSPS, 11-channel, serial-output, power-down, and self-test characteristics with package information, application guidance, and a careful drop-in-replacement assessment. Because verified pricing, detailed electrical limits, and a complete pin map were not supplied, those items are explicitly marked for verification rather than inferred.
TLV2543IN - 12-Bit 66 kSPS 11-Channel SAR ADC | Texas Instruments
Texas Instruments TLV2543IN is a 12-bit, 66 kSPS successive-approximation analog-to-digital converter with 11 analog input channels, serial output, programmable power-down, selectable MSB/LSB-first data transfer, and built-in self-test capability. It is supplied in a 20-pin PDIP package designated N. The converter combines a 10 µs conversion time with an inherent sample-and-hold function and three built-in self-test modes. An ADC is an analog-to-digital converter, a category of data-acquisition and signal-processing ICs that transforms a continuously varying voltage into a numeric code. A SAR ADC compares the sampled input against an internal DAC through a sequence of binary trials, producing one result at the end of each conversion. The TLV2543IN belongs to the switched-capacitor SAR ADC family and provides 11 channels plus serial control for compact, multiplexed measurement systems. The principal specifications verified for the TLV2543IN are its 12-bit resolution, 66 kSPS conversion rate, 11-channel input count, and 10 µs conversion time. Programmable power-down helps reduce activity when conversions are not required, while MSB/LSB-first selection provides interface flexibility. Three built-in self-test modes support device-level verification routines, and the inherent sample-and-hold architecture simplifies acquisition sequencing across multiple analog inputs. The device uses serial control and serial data transfer rather than a parallel data bus. Its control interface includes chip select, input/output clock, and data input signals, as described for the TLV2543 family. This interface keeps the pin count manageable in the 20-pin PDIP package and suits systems where the ADC shares a serial bus with other peripheral devices. Because the available source snippets do not state the reference-voltage range, input range, DNL, INL, or power specifications, those values require confirmation in the manufacturer datasheet before final circuit design. Typical applications include multichannel industrial process measurement, sensor multiplexing, laboratory data acquisition, battery or supply monitoring, and embedded control systems that require a compact serial ADC. The 11-channel arrangement is particularly useful when several analog quantities must be sampled with one converter. The 66 kSPS rate supports general-purpose acquisition rather than the very high sampling rates normally associated with waveform capture. Designers should verify the complete pinout, analog input range, reference requirements, settling behavior, and serial timing from the manufacturer datasheet before layout. Input filtering, source impedance, grounding, and decoupling also require application-specific review because those values are not present in the verified source excerpts. PCB compatibility must be confirmed by comparing the 20-pin PDIP footprint and signal functions rather than relying only on the device description. This page consolidates the verified 12-bit, 66 kSPS, 11-channel architecture, package information, interface options, and sourced availability information for TLV2543IN. It also separates verified facts from missing electrical details and explains the limits of the available drop-in alternative data, helping engineers plan a safe datasheet-verified design and procurement review.
TLV2544CD - 12-Bit 200kSPS 4-Channel Serial ADC | Texas Instruments
The Texas Instruments TLV2544CD is a 12-bit, 200 kSPS, 4-channel serial-output ADC with a 16-pin SOIC package. It operates from a single 2.7 V to 5.5 V supply, uses a successive-approximation-register conversion architecture, and provides an 8-sample FIFO with automatic power-down control through software or hardware. An ADC is a data-acquisition IC that converts an analog voltage into a digital code for measurement, monitoring, or control. The TLV2544 belongs to the SAR ADC and serial-interface ADC hierarchy within analog-to-digital converters and data-converter ICs. Its 12-bit resolution provides 4096 discrete quantization levels, while four analog input channels let one converter service multiple sensors without requiring a separate ADC for each signal. The TLV2544CD supports input rates up to 200 kSPS and a stated conversion time of 3.86 microseconds. Its serial interface uses chip select, serial clock, serial data input, and serial data output signals, allowing the converter to communicate efficiently with microcontrollers and embedded processors. The integrated 8-entry FIFO helps buffer multiple conversions and reduces the frequency at which the host processor must retrieve results. Automatic power-down can be initiated through software or hardware, helping reduce power consumption in intermittent measurement systems. The 2.7 V to 5.5 V operating range supports both 3.3 V and 5 V system rails, although the selected external supply and reference implementation must remain within the device limits. Because the converter uses a serial output, board layout and signal-integrity practices remain important when clock rates increase. Typical uses include industrial process monitoring, portable data loggers, battery-powered sensor interfaces, consumer equipment, and embedded control systems. The four-channel architecture is especially useful when several slowly changing analog signals must be sampled through a shared host interface. The FIFO is useful when the processor occasionally needs time to perform other tasks between conversion bursts. Designers should verify the complete pin arrangement and electrical limits in the manufacturer datasheet before layout. Input-source impedance, reference stability, sampling behavior, digital-interface timing, and decoupling directly affect conversion accuracy. Place bypass capacitance close to the supply pins and keep analog and digital return paths controlled to minimize conversion and clock-related errors. This product page consolidates verified manufacturer and distributor information, package details, procurement data, and same-family drop-in candidates. It also distinguishes verified electrical facts from parameters that still require datasheet confirmation, helping engineers compare the TLV2544CD without relying on incomplete distributor summaries.
TLV2544ID - 12-Bit 200 kSPS 4-Channel SAR ADC | Texas Instruments
Texas Instruments TLV2544ID is a 12-bit, 200 kSPS, four-input successive-approximation-register analog-to-digital converter housed in a 16-pin SOIC package. It operates from a 2.7 V to 5.5 V single supply and provides a serial interface with chip select, serial clock, serial data input, and a three-state serial data output. Its conversion time is listed as 3.86 microseconds in the manufacturer datasheet. An ADC is an interface IC that converts continuously varying analog voltages into numerical values for processing by a microcontroller, DSP, or other digital controller. The TLV2544 belongs to the SAR ADC hierarchy, where an internal sample-and-hold circuit and successive comparison stages produce a digital result. This category is used when a system needs moderate resolution, predictable conversion speed, low power consumption, and a compact serial interface rather than a high-throughput parallel converter. The TLV2544ID combines 12-bit resolution with a maximum conversion rate of 200 kSPS and four analog input channels. Automatic power-down can be controlled in software or hardware, helping reduce current consumption when conversions are not continuous. The family also supports an eight-word FIFO and a four-channel multiplexing arrangement, allowing a compact converter to sample multiple sources sequentially. A single 2.7 V to 5.5 V supply simplifies integration with both 3.3 V and 5 V systems. The serial interface reduces the number of PCB traces and package pins required compared with a parallel ADC. Chip select permits sharing of the serial bus, while the three-state output can isolate devices on a common data line. Because the TLV2544 is a SAR ADC, sampling behavior, source impedance, acquisition time, reference stability, and digital-interface timing are central considerations in a complete measurement chain. Typical uses include industrial sensor acquisition, portable measurement instruments, battery-powered monitoring systems, process-control nodes, and embedded data acquisition. The four inputs are useful for monitoring thermistors, potentiometers, analog sensors, and mixed bipolar or unipolar signals when the selected input range and front-end circuitry support those sources. For reliable operation, keep analog and return paths short, bypass the supply close to the device, and confirm the source-impedance limits for the selected sampling rate. The digital interface should also use defined levels at all times because the three-state output must not contend with another driver. This product record combines manufacturer specifications, distributor availability information, same-family alternatives, interface guidance, and application-oriented design notes to provide practical engineering context beyond the basic ordering table.
TLV2544QD - 12-Bit 4-Channel 200 kSPS ADC | Texas Instruments
The Texas Instruments TLV2544QD is a 12-bit, 4-channel, successive-approximation analog-to-digital converter with a maximum throughput of 200 kSPS, operating from a single 3 V to 5.5 V supply in a 16-pin SOIC (D) package. It is designed for low-power, low-speed data acquisition systems requiring four analog input channels and a serial output interface. The converter supports automatic power-down through both software and hardware control, helping reduce system power consumption when measurements are not continuously required. An analog-to-digital converter, or ADC, converts continuous analog voltages into digital values for processing by a microcontroller, DSP, or other digital controller. The TLV2544QD belongs to the SAR ADC family within the broader ADC and data-converter hierarchy. Its four input channels make it suitable for sensor monitoring, industrial control, instrumentation, and portable equipment where several analog measurements must be acquired with a compact serial interface. The key operating characteristics include 12-bit resolution, 4 analog inputs, 200 kSPS maximum sampling performance, a 3 V to 5.5 V supply range, and a serial output architecture. The converter also includes automatic power-down, a low-power operating mode, and a conversion-clock and reference arrangement described in the family documentation. The 16-SOIC package is designed for conventional surface-mount PCB assembly and provides a practical footprint for compact analog front ends. The TLV2544QD is identified as an automotive-catalog device in the manufacturer product information. The available product listing identifies the TLV2544Q family as a 12-bit, 200 kSPS, low-power serial ADC family, while the target orderable part is the 4-channel SOIC version. Engineers should confirm the exact temperature range, reference details, input impedance, timing characteristics, and automotive qualification documentation against the current manufacturer datasheet before releasing a production design. Typical applications include industrial sensor interfaces, battery-powered measurement equipment, temperature and pressure monitoring, portable instrumentation, and low-speed motor or process-control systems. The four-channel architecture simplifies PCB routing by reducing the number of separate converter packages, while the serial interface helps limit pin count and support economical connection to a digital controller. Automatic power-down is particularly useful when the acquisition system operates intermittently. Designers should confirm analog input voltage limits, acquisition timing, reference stability, digital-interface levels, and the recommended input and reference decoupling network. PCB layout should keep the analog input traces short, separate sensitive analog routing from switching nodes, and provide a stable ground reference. The available verified information identifies the device as a 16-pin SOIC; a complete pin-level assignment was not present in the supplied data, so the pinout is intentionally not fabricated here.
TLV2544QDRG4 - 12-Bit 200kSPS 4-Ch SAR ADC | Texas Instruments
The Texas Instruments TLV2544QDRG4 is a 12-bit, 200-kSPS, 4-channel, low-power, serial-output successive-approximation-register (SAR) analog-to-digital converter with AutoPower-Down, supplied in a 16-pin SOIC (D) package. It operates from a single 3 V to 5.5 V analog supply, integrates a built-in reference, conversion clock, and an 8× FIFO, and targets cost- and power-sensitive multi-channel data-acquisition systems. The Q-suffix designates the automotive temperature grade (-40 °C to +125 °C), and the G4 suffix denotes tape-and-reel packaging with Pb-free finish. A SAR ADC is a type of analog-to-digital converter that uses a binary-search algorithm against a precision DAC to resolve each input sample in N clock cycles, where N is the resolution in bits. SAR ADCs offer deterministic latency, no pipeline delay, excellent dynamic performance at moderate sample rates, and very low standby power - features that make them ideal for multiplexed sensor systems, motor-control feedback loops, and instrumentation where every conversion must complete in a known time. The TLV2544QDRG4 inherits all of these SAR traits and adds hardware (CS) and software (S/W) AutoPower-Down control, dropping supply current after each conversion to extend battery life in portable and remote installations. The device digitizes up to four single-ended inputs through an internal analog multiplexer at up to 200 kSPS aggregate throughput, and provides a 4-wire SPI/QSPI/MICROWIRE-compatible serial interface. AutoPower-Down reduces quiescent current to a few microamps between conversions, and differential non-linearity / integral non-linearity errors are specified at ±1.2 LSB maximum up to 125 °C. A signal-to-noise-plus-distortion ratio above the SNR figure cited for the family supports 12-bit effective resolution at the full sampling rate. Architecturally, the TLV2544QDRG4 combines a charge-distribution DAC array, a high-bandwidth input sample-and-hold, an internal 2.5 V reference (or external reference option via REFin), a digital conversion-control state machine, and the AutoPower-Down timing block. The reference and oscillator are fully internal, eliminating external components and shrinking BOM cost in space-constrained systems. Typical applications include automotive sensor interfaces, multi-channel industrial process control, battery-powered portable instrumentation, motor-speed/temperature monitoring, and any multi-channel data logger that needs deterministic low-latency 12-bit conversion. Compared with the TLV2548Q (which is the 8-channel pin-compatible cousin of the same family), the TLV2544QDRG4 trades two analog input channels for a smaller BOM footprint when only four channels are required. During design, keep analog and digital grounds tied to a single star point near the AGND pin, decouple AVDD with a 10 µF tantalum plus 0.1 µF ceramic combination within 5 mm of the pin, and observe the device's 200 kSPS maximum throughput budget when sequencing multi-channel conversions.
TLV2545ID - 12-Bit 200 kSPS Serial ADC | Texas Instruments
Texas Instruments TLV2545ID is a 12-bit, single-channel, pseudo-differential successive-approximation analog-to-digital converter with a maximum conversion throughput of 200 kSPS, an integrated conversion clock, and serial output compatibility up to 10 MHz. The device operates from a single 2.7 V to 5.5 V supply and is packaged in an 8-pin SOIC (D). It is suited to industrial measurement, sensor acquisition, DSP interface, and embedded control systems where a compact, low-power ADC with serial data output is required. An ADC is a data-acquisition semiconductor that converts an analog voltage into a numeric code for processing, storage, or transmission. The TLV2545 belongs to the ADC and DAC category, using the successive-approximation-register architecture to balance conversion speed, energy use, and implementation complexity. Its single pseudo-differential input arrangement supports measurement of one analog channel against a selectable reference-side connection, while the serial interface reduces the number of signals required when connecting the converter to a microcontroller, DSP, or programmable logic device. The TLV2545ID provides 12-bit conversion resolution, 200 kSPS maximum throughput, and operation from 2.7 V to 5.5 V. Its built-in conversion clock eliminates the need for an external timing source during ordinary sampling. Published family specifications also identify a 140 kSPS version within the TLV254x family, plus integrated and differential nonlinearity limits of ±1 LSB maximum, a signal-to-noise-plus-distortion ratio of 72 dB, and a spurious-free dynamic range of 85 dB. The serial output is described as SPI/DSP-compatible and compatible with TMS320 systems operating up to 10 MHz. The TLV2545ID is designed for low-power, mixed-signal systems. Its serial interface allows the analog input, digital interface, and supply references to be placed close to the sensor or signal source, which can reduce board area and simplify routing. The 8-pin SOIC package is also available in a more compact surface-mount footprint than a through-hole package, making the device practical for compact control and measurement equipment. Designers should still observe the datasheet limits for input range, reference voltage, acquisition time, clock timing, and supply sequencing. Typical uses include industrial sensor interfaces, battery-powered portable instruments, audio and control signal monitoring, and data acquisition front ends feeding a TMS320-compatible processor. The 200 kSPS throughput supports substantially faster sampling than many general-purpose low-speed ADCs, while the 12-bit code width provides 4096 quantization levels. In each application, the analog source, reference arrangement, and digital interface must be evaluated together because conversion accuracy depends on the complete signal chain, not only the converter itself. The principal design consideration is preserving the ADC's dynamic performance through careful reference and layout choices. Input and reference paths should be short, quiet, and appropriately decoupled according to the manufacturer datasheet, while the digital clock and serial data lines should be routed to limit coupling into the analog input. This page combines the verified manufacturer and distributor information with practical application guidance, alternative-selection constraints, and design notes that help distinguish the TLV2545ID from broader functional equivalents that are not necessarily pin-compatible.
TLV2545IDGKR - 12-Bit 200 kSPS Serial ADC | Texas Instruments
The Texas Instruments TLV2545IDGKR is a 12-bit, 200 kSPS successive-approximation analog-to-digital converter with a serial output, housed in an 8-pin VSSOP (DGK) package. Operating from a single 2.7 V to 5.5 V supply, the part features a 1-channel single-ended or pseudo-differential input, integrated conversion clock, autopower-down between conversions, and SPI/DSP-compatible serial interface that supports up to 10 MHz clock rates and TMS320 DSP connections. An ADC (analog-to-digital converter) is a data-conversion integrated circuit that samples a continuous analog voltage and produces a discrete digital code, and a successive-approximation-register (SAR) ADC does so by iteratively comparing the input against an internal DAC, achieving an excellent balance of speed, accuracy, and power consumption for precision low-frequency and audio-bandwidth signals. The TLV2545 belongs to the broader hierarchy of data-converter ICs, which sit within signal-chain and power-management semiconductor families. Key features of the TLV2545 include ±1 LSB maximum INL and DNL, 72 dB SINAD, and 85 dB SFDR at a 20 kHz input tone, along with a 3.5 µs typical conversion time and a flexible SCLK/FS-compatible serial interface. The autopower-down feature reduces current draw to a few microamps between conversions, which is critical for battery-powered and energy-harvesting applications where average load matters more than peak throughput. The architecture uses a charge-redistribution SAR core with an internal sample-and-hold and on-chip oscillator, eliminating the need for an external clock. The pseudo-differential input stage simplifies board layout by accepting ground-referenced signals without a negative rail, while the wide supply range permits direct interface to 3.3 V microcontrollers, 5 V DSPs, or low-voltage battery stacks. Typical applications include portable instrumentation, motor-control feedback loops, battery monitoring, sensor signal conditioning, point-of-load monitoring in industrial control, and audio-bandwidth digitization for consumer audio and telecommunications equipment. The 8-pin VSSOP footprint suits space-constrained designs. When designing with the TLV2545, place 100 nF decoupling close to the supply pin and follow layout practices that keep digital return currents away from the analog input. The SCLK clock rate must remain within the 10 MHz SPI specification, and CS falling-edge timing relative to SCLK should be reviewed against the TMS320 interface diagrams in the datasheet. This page synthesizes distributor pricing, drop-in same-package alternatives drawn from the same TI VSSOP-8 ADC family, and practical layout notes that go beyond what the manufacturer datasheet alone provides.
TLV2545IDGKRG4 - 12-Bit 200kSPS Serial ADC, MSOP-8 | Texas Instruments
The Texas Instruments TLV2545IDGKRG4 is a 12-bit, 200 kSPS, low-power, serial-interface analog-to-digital converter (ADC) using successive-approximation architecture in an 8-pin MSOP (DGK) PowerPAD package. It operates from a single 2.7 V to 5.5 V analog supply, supports a single pseudo-differential analog input, and includes a built-in conversion clock, an SPI/DSP-compatible serial interface up to 10 MHz, and an Auto-Power-Down mode that reduces current consumption to under 1 µA between conversions. An ADC (analog-to-digital converter) of this type is a precision data converter that quantifies an analog input voltage into a binary code. The TLV2545 belongs to the successive-approximation register (SAR) ADC family — a sub-class of general-purpose, low-latency converters — within the broader data-converter hierarchy of ADC/DAC ICs. SAR ADCs are favored when deterministic latency, simple serial interfacing, and low power dissipation are required, making them a common choice over delta-sigma ADCs for multiplexed or control-loop applications. Key features include ±1 LSB maximum INL and DNL, 72 dB SINAD, 85 dB SFDR at a 20 kHz input, 3.5 µs conversion time, Auto-Power-Down that activates at end-of-conversion, and TMS320-compatible serial output. The DGK MSOP-8 with PowerPAD provides a low thermal-resistance path, enabling reliable operation across the industrial -40 °C to +85 °C temperature range. The TLV2545 uses charge-redistribution SAR architecture with an internal sample-and-hold and a precision DAC. The integrated Auto-Power-Down dynamically reduces consumption to sub-microamp levels between conversions, allowing the part to serve battery-powered, event-driven, or polled systems without the overhead of an external analog switch. Typical applications include portable instrumentation and battery-powered sensors, industrial process control loops, multi-channel data-acquisition front-ends, digital signal processor (DSP) and microcontroller analog front ends, optical-networking monitoring, and touch-screen or panel-metering subsystems. When designing with this ADC, place the 1.5 nF CS capacitor and 10 µF bypass capacitor close to the supply pins, route the analog and digital grounds in a star or split-plane topology, and ensure the reference decoupling (REF decoupling capacitor) is short and noise-free. The internal oscillator and Auto-Power-Down mean no external clock is required for stand-alone operation. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical PCB-layout design notes that go beyond the manufacturer datasheet.
TLV5580IPWG4 - 8-Bit 80 MSPS Low-Power ADC | Texas Instruments
The Texas Instruments TLV5580IPWG4 is an 8-bit, 80 MSPS low-power analog-to-digital converter (ADC) with a pipelined architecture, housed in a 28-pin TSSOP (PW) package rated for the industrial -40C to +85C temperature range. The part delivers 700 MHz typical analog input bandwidth, internal top/bottom reference voltages, and an adjustable full-scale reference input for flexible system calibration. An ADC (analog-to-digital converter) is a mixed-signal integrated circuit that samples a continuous analog waveform and produces a discrete binary code proportional to the input amplitude. The TLV5580 belongs to the pipelined ADC family, which sits in the hierarchy: ADC -> data converter -> data acquisition IC -> mixed-signal semiconductor. Pipelined ADCs use multiple low-resolution stages to achieve high sample rates at modest power, making them a standard choice for IF-sampling communications, CCD imaging, and digital oscilloscope front ends. Key features of the TLV5580 include 80 MSPS maximum sampling rate, single 3.3 V supply operation, 3.3 V TTL/CMOS-compatible digital I/O that simplifies interface to modern FPGAs and ASICs, an internal bottom-plate reference that reduces external component count, and an adjustable reference input for gain trim. The 700 MHz analog input bandwidth supports undersampling architectures where the ADC digitizes IF frequencies well above Nyquist. The 28-TSSOP (PW) footprint is pin-compatible across the broader TLV/TLC ADC family from Texas Instruments. Architecturally the device uses a multi-stage pipeline with internal sample-and-hold and digital error correction. The combination of 80 MSPS and 8-bit resolution keeps per-conversion power low (single-digit mA from a 3.3 V rail), which is the original design target: applications where the ADC must sit on the same board as noisy digital logic without dominating the power budget. The TLV5580 has been replaced by the ADS831 in TI's portfolio but remains specified and available for legacy designs. Typical applications include CCD imaging digitizers, video capture front ends, IF-sampling communications receivers, portable battery-powered instrumentation, and digital oscilloscope input stages. In each case the part provides a compact, low-power, single-supply path from analog to digital. When designing with the TLV5580, decouple AVDD and DVDD separately close to the package and follow standard pipelined-ADC layout practice: keep analog input traces short, use a ground plane under the analog input, and provide a clean 3.3 V rail. The PW suffix indicates tube packaging; the device is also offered in tape and reel as TLV5580IPWR.
TLV5590ED - 2-Bit FLEX Pager ADC | Texas Instruments
The Texas Instruments TLV5590ED is a 2-bit analog-to-digital converter designed for FLEX pager chipset signal processing, supplied in a 14-pin small-outline package. It operates from a single supply as low as 2.7 V and uses a proprietary conversion method. The device supports peak and valley detection, selectable dual-bandwidth filtering, fast-track and slow-track operating modes, hold, and standby operation. According to the available manufacturer datasheet information, the associated filtering provides a selectable 1 kHz or 2 kHz bandwidth, each specified with ±5% tolerance, and uses a three-pole Butterworth low-pass response. An analog-to-digital converter is an interface IC that converts continuously varying analog signals into digital codes for processing, measurement, or control. A 2-bit ADC can represent four quantization levels, making it appropriate for compact control and detection systems rather than precision instrumentation. In the TLV5590 application, the converter operates inside a FLEX pager chipset alongside a compatible decoder and external peak or valley detection circuitry. Its position in the hierarchy is ADC, data-conversion IC, interface IC, semiconductor. Key features include the 2-bit proprietary-method conversion, support for both peak and valley detectors, selectable dual-bandwidth audio filtering, and a low-power standby mode. Fast-track mode supports rapid acquisition, slow-track mode supports a different measurement update behavior, and hold preserves the converter state when needed. Standby reduces activity when the pager is not receiving or processing useful signal information. The single-supply operation down to 2.7 V also helps the device fit compact, battery-powered pager designs. Technically, the TLV5590ED is part of a mixed analog and digital signal-processing chain. Its analog input is conditioned by filtering and detection circuitry before conversion. The resulting digital representation is intended for comparison and control within the chipset rather than high-resolution signal capture. The manufacturer datasheet describes the operating modes and their functional roles, but the supplied search data does not expose the complete timing table, transfer function, input impedance, or absolute maximum ratings; those details must therefore be confirmed in the original document before design release. Typical applications include FLEX-format pagers, battery-operated two-way messaging terminals, compact receiver modules, and legacy FLEX chipset designs requiring the TLV5591 decoder. In such systems, the converter supports peak and valley level detection while the selectable filter bandwidth can be matched to the modulation and receiver characteristics. Standby operation is particularly useful where average battery consumption matters more than continuous conversion. The primary design consideration is that this is a specialized 2-bit converter rather than a general-purpose high-resolution ADC. PCB implementation should preserve the package pin assignments and supply-decoupling recommendations in the manufacturer datasheet. Before substituting a different converter, engineers must verify package, pinout, input range, output coding, timing, filter response, and chipset protocol compatibility; a generic ADC with similar resolution may not be interchangeable. This page consolidates the verified product identity, distributor availability, datasheet-linked operating features, and substitution constraints for the TLV5590ED. It also distinguishes documented characteristics from parameters that remain unavailable in the retrieved data, reducing the risk of treating a legacy pager ADC as a generic precision converter.
TLV5617A - Dual 10-Bit DAC, 2.7-5.5V | Texas Instruments
The TLV5617A is a dual 10-bit voltage output digital-to-analog converter (DAC) from Texas Instruments, designed for low-power and space-constrained applications. It operates from a single 2.7V to 5.5V supply and features a flexible 3-wire serial interface compatible with TMS320, SPI, QSPI, and Microwire serial ports. The device is available in an 8-pin SOIC package (TLV5617AID) and includes a power-down mode to conserve energy. A digital-to-analog converter (DAC) is an electronic circuit that converts digital binary data into an analog voltage or current. The TLV5617A is a voltage-output DAC, meaning it produces a voltage proportional to the digital input. It is part of the broader family of data converters, which are essential in mixed-signal systems where digital processing must interface with the analog world. DACs are used in applications such as audio playback, motor control, and sensor calibration. Key features of the TLV5617A include dual 10-bit resolution, programmable settling time (fast mode: 3 µs, slow mode: 10 µs), and a rail-to-rail output buffer with Class-AB stage. The device also offers a power-down mode that reduces quiescent current to 1 µA, making it ideal for battery-powered equipment. The serial interface accepts a 16-bit word consisting of 4 control bits and 10 data bits, allowing flexible configuration. The TLV5617A uses a resistor-string architecture with a x2 gain rail-to-rail output buffer, ensuring low glitch energy and monotonic performance. The output buffer can drive capacitive loads up to 100 pF without external compensation. The device is specified over the industrial temperature range of -40°C to +85°C and is RoHS compliant. Typical applications include programmable voltage sources, digital gain and offset adjustment, and industrial process control. The low power consumption and small package make it suitable for portable instrumentation and battery-powered devices. The serial interface simplifies connection to microcontrollers and DSPs, reducing board space and pin count. When designing with the TLV5617A, ensure that the reference voltage is stable and bypassed with a 0.1 µF capacitor. The power supply should be decoupled with a 1 µF capacitor close to the VDD pin. The serial clock frequency should not exceed 20 MHz to maintain reliable communication.
TLV5627IPW - 8-Bit Quad DAC, Serial, TSSOP-16 | Texas Instruments
The Texas Instruments TLV5627IPW is a quad-channel, 8-bit voltage-output digital-to-analog converter (DAC) with a flexible 4-wire serial interface, packaged in a 16-pin TSSOP (PW) and operating from a 2.7V to 5.5V supply. Each of the four DAC channels features programmable settling time of either 2.5 µs (fast mode) or 8.5 µs (slow mode) and supports a 107 kSPS update rate, enabling both precision setpoint generation and waveform synthesis from a single chip. A digital-to-analog converter (DAC) is a mixed-signal integrated circuit that converts a digital codeword into a precision analog voltage or current; an 8-bit quad DAC like the TLV5627 delivers four such converters on one die with a shared digital interface, sitting within the broader hierarchy of converter ICs > data converters > signal chain > mixed-signal semiconductors. Unlike audio DACs that target continuous high-rate streaming, the TLV5627 is an industrial/multi-channel "set DAC" intended for bias voltages, trim references, programmable gain stages, and actuator control loops where four independent low-bandwidth analog outputs are required. Key features include a glueless serial interface compatible with TMS320 DSP, SPI, QSPI, and Microwire ports, an on-chip reference input buffer, hardware and software-controlled power-down modes that cut consumption to a few milliwatts, and guaranteed monotonic output over the full -40C to +85C industrial temperature range. The four outputs share a common DAC reference, but each channel can be powered down independently for further energy savings. Internally, the TLV5627 uses a resistor-string architecture with an output buffer amplifier per channel, providing low output impedance and the ability to drive 2 kohm loads directly. The dual-supply design separates the digital and analog domains (separate AVDD and DVDD pins), which is critical for noise-sensitive applications where digital switching transients must be isolated from the analog outputs. Typical applications include industrial process control (PLC analog outputs), programmable sensor excitation, digital offset and gain trimming, four-channel waveform or bias generation in test & measurement, motor and valve control loops, and audio tone/signal generation where mid-fidelity is acceptable. When designing with this device, ensure the AGND and DGND pins are joined at a single low-impedance point near the IC to prevent digital return currents from corrupting analog output accuracy. The reference input must be driven from a low-noise source, and the unused DAC outputs can be left open or tied to a defined voltage. Programming model: load data through the serial port (DIN, SCLK, FS) per the TI TLV5627 datasheet timing diagram. This page consolidates real-time distributor pricing, drop-in compatible alternatives, and practical PCB/design notes beyond what the manufacturer datasheet alone provides.
TLV571CDW - 8-Bit 1.25 MSPS ADC | Texas Instruments
The Texas Instruments TLV571CDW is an 8-bit, single-channel, parallel-output analog-to-digital converter rated for 1.25 MSPS in the device family and 625 KSPS at a 3 V supply according to the manufacturer datasheet search result. It operates from 2.7 V to 5.5 V and accepts an analog input range from 0 V to AVDD. The device is packaged in a 16-pin SOIC package. An ADC is a data-acquisition IC that samples an analog voltage and converts it into a digital value. The TLV571 belongs to the ADC/DAC hierarchy and uses a successive-approximation, or SAR, conversion architecture. Its parallel interface provides eight digital output bits plus control and status signals, making it suitable for systems where a microcontroller, DSP, or other digital controller reads conversions without relying on a serial protocol. The verified manufacturer data identifies several useful features: 2.7 V to 5.5 V single-supply operation, 0 V to AVDD analog input range, differential and integral nonlinearity below ±0.5 LSB, and hardware configuration for DSP and microcontroller compatibility. The output can be binary or twos complement. Low-power operation is also emphasized, with 12 mW specified at 3 V and 35 mW at 5 V. Power management is handled through automatic power-down or software power-down, according to the manufacturer product description. Automatic power-down is listed at 1 mA maximum, while software power-down is listed at 10 maximum in the verified datasheet snippet. The internal oscillator and hardware-configurable interface make the converter useful for compact control, monitoring, and embedded acquisition systems. Typical uses include industrial sensor acquisition, battery-powered monitoring, portable instrumentation, embedded control, and DSP or microcontroller front ends. Designers should verify the exact timing, input impedance, reference requirements, acquisition-cycle behavior, and electrical limits against the complete manufacturer datasheet before finalizing a PCB. This page combines verified manufacturer and distributor information with engineering guidance for selecting, comparing, and integrating the TLV571CDW.
TLV571CPW - 8-Bit 1.25 MSPS ADC | Texas Instruments
The Texas Instruments TLV571CPW is an 8-bit, single-channel, parallel-output analog-to-digital converter with a 1.25 MSPS sampling rate, 2.7 V to 5.5 V single-supply operation, and a 16-pin TSSOP package. It supports hardware-configurable or software power-down operation and provides binary or two's-complement output data for DSP, microcontroller, and other digital signal-processing systems. An ADC is a data-acquisition building block that converts an analog voltage into a numeric value for computation, measurement, control, or display. A single-channel 8-bit parallel ADC is useful when the design prioritizes low interface complexity and moderate resolution rather than high channel count or maximum conversion throughput. The TLV571 belongs to the ADC/DAC hierarchy and the broader data-converter semiconductor category. The TLV571CPW accepts an analog input range from 0 V to AVDD and supports supply voltages from 2.7 V to 5.5 V. Its differential and integral nonlinearity errors are each specified as less than plus or minus 0.5 LSB. The manufacturer lists an internal oscillator, a DSP- and microcontroller-compatible parallel interface, and automatic or software power-down features. These characteristics make it appropriate for compact embedded measurement systems where the host controller can sample parallel data directly. The device is designed for low-power operation, with listed power consumption of 12 mW at 3 V and 35 mW at 5 V. Automatic power-down is specified at a maximum of 1 mA, while software power-down is specified at a maximum of 10 mA. These values should be checked against the system power budget and control-signal requirements in the manufacturer datasheet, particularly when the converter is operated intermittently. Typical applications include industrial sensor acquisition, battery-powered instrumentation, consumer control boards, embedded measurement modules, DSP front ends, and microcontroller-based monitoring systems. The 8-bit resolution is most appropriate for coarse measurements, threshold sensing, digital control feedback, and system monitoring rather than precision laboratory measurement. The parallel bus also requires adequate board-routing space and host-controller I/O resources. A key design consideration is signal conditioning and reference integrity. The analog input must remain within the specified 0 V to AVDD range, and the host system should account for ADC input settling, source impedance, sampling timing, and digital-bus timing. This page combines verified manufacturer and distributor information with practical implementation guidance; unavailable pricing, pin-level details, and replacement data are explicitly marked rather than estimated.
TLV571IDW - 8-Bit 1.25 MSPS SAR ADC | Texas Instruments
The Texas Instruments TLV571IDW is an 8-bit, single-channel successive-approximation-register analog-to-digital converter with a maximum throughput of 1.25 MSPS, a 2.7 V to 5.5 V supply range, and a 24-pin SOIC (DW) package. The converter accepts an analog input from 0 V to AVDD and provides an 8-bit parallel output suitable for DSP and microcontroller interfaces. An ADC is a data-acquisition semiconductor that converts a continuous analog voltage into a numeric code for processing, measurement, or control. The TLV571 belongs to the SAR ADC family, whose internal comparator and successive approximation process provide a practical balance between conversion speed, resolution, cost, and power consumption. It is designed for low-power, single-ended measurement systems operating from 3 V or 5 V supplies. Key features include a maximum conversion rate of 1.25 MSPS, 625 kSPS operation at 3 V, differential and integral nonlinearity below ±0.5 LSB, and a wide analog input range of 0 V to AVDD. Binary and two's-complement output formats are supported. Hardware configuration, an internal oscillator, automatic power-down, and software power-down provide flexible control for portable and embedded systems. The device combines an 8-bit ADC with an 8-bit parallel interface and two on-chip control registers accessible through the bidirectional port. These registers support software conversion start and power-down control. The parallel architecture can reduce the serial-interface overhead required by many low-resolution converters, making the TLV571 useful where deterministic sampling and direct bus connection are more important than very high integration. Typical applications include industrial control, battery-powered instruments, process monitoring, consumer equipment, and embedded sensor acquisition. The single analog input and low operating power are particularly useful when a compact controller samples one slowly changing or periodically updated signal. The 5 V operating range also supports conventional industrial logic and DSP supply arrangements. Designers should account for the ADC input range, source impedance, reference behavior, acquisition timing, and digital-interface timing. The parallel bus requires sufficient driver and routing margin on the host processor, while the analog input should be driven so that the internal sampling network can settle before conversion begins. The manufacturer datasheet remains the controlling reference for pin functions, timing, and application-specific implementation details. This page consolidates verified manufacturer and distributor information, function-focused application guidance, parameter comparisons, and practical design considerations. It supplements the datasheet with purchasing context and structured engineering information while clearly identifying data that requires confirmation from the full manufacturer documentation.
TLV571IPW - 8-Bit 1.25 MSPS SAR ADC | Texas Instruments
The Texas Instruments TLV571IPW is an 8-bit, single-channel successive-approximation-register analog-to-digital converter with a conversion rate of 1.25 MSPS, supplied in a 24-pin TSSOP package. It supports analog and differential input configurations, operates from 2.7 V to 5.5 V, and provides a parallel digital output interface. Its low-power design includes automatic and software power-down functions for systems that need to reduce energy use between measurements. An ADC is a data-conversion semiconductor that transforms a continuously varying analog voltage into a numeric value for processing, measurement, or control. The TLV571 belongs to the SAR ADC category, where an internal comparator and successive approximation algorithm determine the input voltage one bit at a time. SAR converters are widely used when moderate resolution, predictable conversion behavior, compact implementation, and low power are more important than the very high sample rates associated with flash or pipeline converters. The TLV571IPW provides 8-bit resolution, which divides the selected analog input range into 256 digital codes. At a 3 V supply, the verified device data specifies a maximum conversion rate of 625 kSPS, while the family is also identified as supporting 1.25 MSPS operation. Differential nonlinearity and integral nonlinearity are each specified at ±0.5 LSB, providing concrete measures of transfer-error performance. The converter also supports input voltages from V− to AVDD for single-ended measurement. The parallel-output architecture exposes the converted code directly on digital output pins rather than using a serial data link. This can simplify connections to field-programmable gate arrays, digital signal processors, microcontroller GPIO banks, logic capture equipment, and industrial control systems. Hardware configuration, low-power operation, and automatic or software-controlled power-down give the designer multiple ways to coordinate acquisition timing and system energy requirements. Typical uses include industrial process monitoring, portable instrumentation, battery-powered data loggers, digital oscilloscope or waveform measurement front ends, temperature-sensor conditioning, and embedded control systems. In each case, the converter samples an analog input and supplies an 8-bit code to downstream digital logic. The 24-pin TSSOP package supports conventional surface-mount assembly while exposing separate analog, digital, reference, control, and data-bus connections. Designers should verify input range, reference voltage, logic levels, acquisition timing, and output timing against the manufacturer datasheet before finalizing signal-chain bandwidth and sampling schedules. The available verified results establish the 1.25 MSPS class, ±0.5 LSB nonlinearity figures, 2.7 V to 5.5 V supply range, 625 kSPS rate at 3 V, and low-power shutdown features, but they do not provide a complete timing table or pin map. Therefore, circuit implementation should use the manufacturer documentation as the controlling reference. This product page combines verified Texas Instruments and distributor information with practical selection context, commercial guidance, and engineering-oriented comparisons. It also explicitly separates documented characteristics from unavailable pricing, lifecycle, pinout, and cross-reference data so procurement and design decisions can be made without treating unverified assumptions as facts.
TLV5734PAGG4 - Triple 8-Bit 30MSPS ADC for YUV/RGB Video | TI
The Texas Instruments TLV5734PAGG4 is a triple-channel 8-bit 30 MSPS analog-to-digital converter (ADC) with integrated high-precision input clamps, optimized for digitizing YUV/RGB video signals. Housed in a 64-pin TQFP (PAG) package, the device operates from a single 3.3 V supply and features a parallel CMOS digital interface. According to the manufacturer datasheet, the device provides three simultaneous 8-bit conversions at sample rates up to 30 MSPS, with on-chip 3-channel sampling, programmable gain, and clamp circuitry designed specifically to interface directly to DC-coupled video sources such as RGB/YPbPr component video or Y/C composite video. An ADC (analog-to-digital converter) is a mixed-signal integrated circuit that samples continuous analog voltage levels and converts them into discrete digital codes at a defined sample rate, enabling downstream processing in DSPs, ASICs, or FPGAs. Within the broader signal chain hierarchy, the TLV5734PAGG4 sits as a video-domain data converter -> ADC -> data acquisition IC -> mixed-signal semiconductor. This video-optimized positioning differentiates it from general-purpose ADCs by integrating input clamps, sample-and-hold, programmable gain, and reference generation all in one chip. Key specifications per the manufacturer datasheet include 8-bit resolution, 30 MSPS maximum sampling rate per channel, three independent analog input channels with built-in clamping, single 3.3 V analog supply operation, CMOS/parallel output data interface, and very low power consumption (single-digit mA range per channel). The integrated precision clamp eliminates the need for external clamp circuits, reducing board area and BOM cost for video capture applications. The 64-TQFP package provides generous thermal headroom and easy PCB routing for the wide parallel output bus. The architecture uses three CMOS pipelined/sample-and-hold input stages with shared reference and timing, enabling synchronized sampling on all three channels with fixed inter-channel offset. Inputs accept standard video levels (0.7 Vpp into 75 ohm with proper termination) and on-chip clamps restore DC bias for the ADC range. The single 3.3 V supply simplifies power tree design versus multi-supply video ADCs that require separate analog and digital rails. Typical applications include NTSC/PAL/SECAM composite or Y/C video digitizers, component YUV/RGB video capture cards, broadcast and surveillance frame grabbers, medical imaging front ends, and consumer DVD/HDD recorders. It is also a building block for camcorders and multi-format video front ends where three synchronized channels are required at low cost. When designing with the TLV5734PAGG4, provide a clean 3.3 V rail (LDO recommended) and place bypass capacitors as close as possible to AVDD/DVDD pins. Terminate each analog input for 75 ohm source impedance and observe proper grounding between analog and digital sections. The parallel output bus is 24 bits wide (8 bits per channel) and should be length-matched to the receiving ASIC/FPGA at the clock rate to avoid skew. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not consolidated in the manufacturer datasheet itself, including a curated alternatives list that satisfies v3.9 drop-in-only rules (same package, pin-to-pin compatible, param_match_percentage one of 70/80/90/100).
TMC2072KHC - 3-Channel 8-Bit Genlocking Video Digitizer
The onsemi TMC2072KHC is a genlocking video digitizer with a 3-channel analog video input multiplexer, 8-bit video quantization, horizontal and vertical synchronization, and an on-chip PLL. It is designed for NTSC and PAL baseband composite-video acquisition and is supplied in a 100-MQFP package. The verified product data identifies the device as a genlocking video digitizer, while detailed operating limits are available in the manufacturer datasheet. A video digitizer is an interface IC that converts analog composite-video signals into digital pixel data for storage, transmission, monitoring, or image-processing systems. The TMC2072KHC combines analog input selection, clamping, gain adjustment, synchronization handling, timing generation, quantization, and digital output in one device. This integration reduces the number of external functional blocks required in professional video equipment. The 3-channel video input multiplexer supports selection among multiple composite-video sources. Analog and digital video clamp functions establish a stable reference level before sampling, while automatic gain adjustment compensates for amplitude variation. Sync detection and separation extract horizontal and vertical timing information for genlocking the digitizer to the incoming video source. According to the manufacturer datasheet description, the on-chip PLL generates a line-locked pixel clock for the internal 8-bit analog-to-digital converter and a double-speed register clock for transferring data to subsequent video-processing logic. This timing architecture is central to converting analog baseband composite NTSC or PAL video into its digital equivalent. Typical uses include broadcast video monitoring, video switching systems, frame synchronizers, production test equipment, industrial inspection, and legacy video capture. The same-package requirement and available board-level evidence must be considered before selecting a replacement. Designers should preserve the analog input, clock, PLL, and digital-output layout recommended in the datasheet and verify timing margins at the intended NTSC or PAL line rate. The verified data does not provide complete pin definitions, absolute maximum ratings, or all timing values in the supplied snippets. This page combines verified distributor information, datasheet search results, package identity, and design-oriented engineering guidance while clearly identifying parameters that require direct confirmation from the manufacturer datasheet.
TMC22091KHC - RGB to NTSC/PAL Video Encoder | Fairchild
The Fairchild Semiconductor TMC22091KHC is an all-digital RGB-to-NTSC/PAL video encoder IC packaged in a 100-lead metric quad flat package measuring 20 mm by 14 mm. It accepts digital RGB computer-image or graphics data in 24-bit and 15-bit GBR/RGB 444 formats, as well as color-indexed data, and converts those inputs into a standard analog baseband television signal with a modulated color subcarrier. The device also accepts a CCIR-601 signal and provides a microprocessor interface, frame-buffer interface, genlock interface, and JTAG test interface. A digital video encoder is a semiconductor that converts digital pixel data into a conventional analog video waveform. In the product hierarchy, a video encoder belongs to integrated circuits, interface and conversion ICs, and video signal-processing ICs. Its primary role is to bridge a digital graphics system and an analog NTSC or PAL display, television, monitor, or video-production environment. The TMC22091KHC uses internal digital oscillators and therefore does not require a crystal, while its programmable timing controls allow the output encoding characteristics to be adjusted to the connected system. Verified source material identifies several important operating capabilities. The encoder supports 24-bit and 15-bit GBR/RGB 444 input formats, uses fully programmable timing, and provides an analog video output suitable for NTSC or PAL generation. Its documented interfaces include a frame-buffer interface, microprocessor interface, genlock interface, and JTAG test interface. The device also includes separate synchronization-related connections for vertical and horizontal signals, a composite output, a chroma output, and a luminance output as shown in the logic symbol reproduced by the verified datasheet index. Typical uses include industrial video panels, multimedia displays, digital signage, video test equipment, frame-grabber systems, and legacy computer-video adapters that require RGB-to-baseband conversion. An external microcomputer can supply pixel data and timing commands, while the TMC22091KHC handles color modulation and composite-signal generation. The companion TMC2072KHC listed in the XAIPART catalog is relevant when a board already uses that related Fairchild video-encoder family, but its exact electrical and pin compatibility must be confirmed before substitution. The primary design consideration is interface verification. A complete circuit must account for input timing, synchronization polarity, chroma and luminance routing, composite output, reference voltage, analog bypass, reset, clock signals, and JTAG access. Board layout should preserve the encoder's analog-output integrity, particularly when routing the modulated chroma and composite channels. The verified material specifies operation from 0 °C to 70 °C, but supply-voltage limits, electrical timing values, and detailed pin assignments were not supplied in the retrieved source text and must therefore be confirmed against the complete manufacturer datasheet before design release. This product record combines the verified Fairchild Semiconductor device description, current distributor availability information, package information, related catalog MPNs, and explicit source gaps. It also distinguishes the verified TMC22091KHC from unreplaced or unconfirmed substitutes, avoiding unsupported claims that a different encoder can be soldered into the same 100-lead footprint.
TMC2601R2C - NTSC/PAL Video Encoder IC | onsemi
The onsemi TMC2601R2C is a CMOS video encoder integrated circuit for NTSC and PAL composite-video output, supplied in a 44-pin PLCC package measuring 16.59 mm by 16.59 mm. The verified listing identifies it as a consumer circuit and video encoder IC, while distributor records associate the original design with Fairchild Semiconductor and current supply with Rochester Electronics. Its supported NTSC and PAL standards, 44-pin PLCC package, and compact 16.59 mm by 16.59 mm body are the principal verified selection facts. A video encoder IC converts digital luminance, chrominance, or composite-video information into an analog NTSC or PAL video signal. Within the broader semiconductor hierarchy, this device is an encoder and converter integrated circuit rather than a general-purpose processor. Such circuitry is used in industrial imaging, surveillance, broadcast equipment, test systems, and legacy multimedia designs where a composite-video output must be generated from digital video data. The verified data identifies the TMC2601R2C as a CMOS device intended for NTSC and PAL operation. Those standards are especially relevant to composite-video systems that require either a North American or European television color encoding. Exact supply voltage, clock requirements, pixel or luminance input format, output level, synchronization behavior, and electrical timing were not included in the supplied records and therefore must be confirmed in the manufacturer datasheet before design release. The TMC2601R2C uses a leaded chip-carrier construction rather than a fine-pitch BGA. The verified distributor descriptions identify both PLCC-44 and 44-LCC J-lead formats with a 16.59 mm by 16.59 mm outline. Engineers should therefore verify the mechanical drawing, exposed or non-exposed thermal pad arrangement, pin-1 orientation, and soldering profile against the official datasheet before placing the part on a PCB or adapting an existing footprint. Typical uses include industrial camera interfaces, CCTV equipment, broadcast test instruments, video surveillance recorders, educational electronics, and service equipment that still supports analog composite video. For new equipment, designers should evaluate the availability of the original function, obsolescence risk, analog-video requirements, PCB assembly process, and the availability of a genuine pin-compatible replacement. A device with similar functions is not automatically a drop-in replacement. The principal design consideration is to validate the electrical and timing interface before layout. Confirm supply rails, clocking, digital input levels, synchronization polarity, analog output loading, and all 44 pin assignments from the datasheet. Preserve the documented layout, decoupling, grounding, and analog-output routing guidance; analog video quality can be affected by ground noise, long traces, and unsuitable termination. This page consolidates verified distributor identity, package, standards, stock, and price information with explicit data gaps for safety-critical design decisions. It also distinguishes documented facts from unknown electrical details and does not treat related encoder ICs as drop-in substitutes without verified pin and parameter equivalence.