بەرهەمەکان (3,600+)

AD7863ARSZ-10REEL - 14-Bit 175kSPS Dual Simultaneous-Sampling ADC | ADI
AD7863ARSZ-10REEL

AD7863ARSZ-10REEL - 14-Bit 175kSPS Dual Simultaneous-Sampling ADC | ADI

The Analog Devices AD7863ARSZ-10REEL is a high-speed, low-power, dual 14-bit simultaneous-sampling analog-to-digital converter (ADC) supplied on a 5 V rail and housed in a 28-pin SSOP package. The part integrates two 5.2 microsecond successive-approximation ADCs, two matched track/hold amplifiers, an internal 2.5 V reference, and a high-speed parallel interface that delivers 175 kSPS per channel with simultaneous sampling across both inputs. With four analog inputs multiplexed through two channels (selected by the A0 logic input), a single CONVST edge places both track/holds into hold and initiates conversion on both ADCs at exactly the same instant, preserving phase information for multi-axis or polyphase systems. A successive-approximation register (SAR) ADC is a binary-search converter that compares the sampled input against an internal DAC, resolving one bit per clock cycle. SAR ADCs are prized for their deterministic latency, intrinsic anti-alias filtering (no switching ripple), and excellent DC linearity - characteristics that make the AD7863 particularly well suited to digitising sinusoidal signals, transducer outputs, and motor-control feedback. Within the broader taxonomy, the AD7863 sits at: ADC -> SAR ADC -> data converter -> signal-chain IC -> semiconductor. Key differentiating features include the simultaneous-sampling dual-channel topology, integrated 2.5 V reference (eliminating an external reference in many designs), low 50 mW typical power consumption from a single 5 V supply, and a high-speed parallel bus that simplifies connection to DSPs, FPGAs, and microcontrollers. The -10 speed grade is the 175 kSPS through-rate variant and is specified across the -40C to +85C industrial temperature range. Typical applications include three-phase motor control and power-line monitoring, instrumentation and data acquisition systems, multi-axis inertial measurement, industrial process control, and medical patient monitoring where synchronised channel capture is required. The internal reference plus parallel bus keeps the BOM small while preserving measurement integrity.

RFQ پەیوەندی
AD7863ARSZ-3REEL - Dual 14-Bit 175 kSPS ADC | Analog Devices
AD7863ARSZ-3REEL

AD7863ARSZ-3REEL - Dual 14-Bit 175 kSPS ADC | Analog Devices

The Analog Devices AD7863ARSZ-3REEL is a high-speed, low-power, dual 14-bit simultaneous-sampling analog-to-digital converter that operates from a single 5 V supply. The device integrates two 5.2 microsecond successive-approximation ADCs, two track-and-hold amplifiers, an internal 2.5 V reference, and high-speed parallel interface logic in a 28-pin SSOP package, with reel packaging for high-volume assembly. An ADC (analog-to-digital converter) is a mixed-signal integrated circuit that converts continuous analog voltages into discrete digital codes. Within the converter hierarchy, successive-approximation register (SAR) ADCs occupy the mid-speed, mid-resolution niche, prized for low latency, deterministic acquisition, and excellent dc accuracy. Simultaneous-sampling SAR ADCs such as the AD7863 capture two channels at exactly the same instant, which is critical for phase-coherent measurements in motor control, power conversion, and instrumentation where vector relationships between signals must be preserved. Key features include four analog input channels arranged as two channel pairs (VA1/VA2 and VB1/VB2), true bipolar input ranges of +/-10 V or +/-5 V (variant dependent -3 is the +/-10 V range), 14-bit resolution with no missing codes, 175 kSPS throughput per ADC, and 5.2 microsecond acquisition time. The internal 2.5 V reference is laser-trimmed for low drift and may be overdriven by an external reference when system-level calibration demands it. Throughput is doubled relative to single-channel architectures because both ADCs sample and convert in parallel. Fabricated in Analog Devices' LC2MOS mixed process, which combines bipolar precision circuits with low-power CMOS logic, the AD7863 achieves high dynamic performance including 80 dB SNR and 90 dB channel-to-channel isolation at the input frequency band. These ac specifications support demanding signal-processing applications such as phased-array sonar, adaptive filters, and spectrum analysis. The parallel interface is directly compatible with standard DSPs and microcontrollers, simplifying system integration. Typical applications include three-phase motor control and power-line monitoring where simultaneous current and voltage sampling is mandatory, multi-axis industrial servo drives, data acquisition systems, and instrumentation requiring synchronized multi-channel measurement. The wide bipolar input range allows direct connection to current shunts, voltage dividers, and transducer bridges without external signal conditioning. Designers should evaluate input common-mode considerations when both channels must reject the same noise, and consider the internal reference bypass requirement of 0.1 microfarad ceramic capacitors on VREF to AGND. The SSOP-28 footprint is footprint-compatible with the AD7863ARZ-3 (SOIC-28) at the schematic level only - PCB layout differs because of the narrower body width. This page synthesizes distributor pricing, pin-compatible alternatives, and practical design notes not found in the manufacturer datasheet alone, giving engineers a single decision-ready reference for sourcing and replacement.

RFQ پەیوەندی
AD7863ARZ-2REEL - Dual 14-Bit 175 kSPS Simultaneous-Sampling ADC | Analog Devices
AD7863ARZ-2REEL

AD7863ARZ-2REEL - Dual 14-Bit 175 kSPS Simultaneous-Sampling ADC | Analog Devices

The Analog Devices AD7863ARZ-2REEL is a high-speed, low-power, dual 14-bit successive-approximation analog-to-digital converter (SAR ADC) operating from a single 5 V supply, housed in a 28-pin SOIC (R-28) wide-body package rated for the industrial temperature range. It integrates two 5.2 μs SAR ADCs, two on-chip track-and-hold amplifiers, an internal 2.5 V reference (with option for external reference), and a high-speed parallel interface capable of 175 kSPS per channel with simultaneous sampling across both channels via a single CONVST edge. Input range is software-configurable to either 0 V to +5 V or ±10 V unipolar/bipolar modes, supported by four analog inputs multiplexed into two ADC channels through the A0 logic input. What is a simultaneous-sampling ADC? A simultaneous-sampling ADC is a data-converter architecture that captures two or more analog signals at the exact same instant through dedicated track-and-hold stages, then digitizes each channel in turn. This matters in motor-control, power-conversion and instrumentation systems where the phase and amplitude relationship between two voltages or currents must be preserved - sequential ADCs would smear that relationship over time. Simultaneous-sampling SAR ADCs sit within the broader hierarchy of data converters (ADC) → SAR ADC → precision ADC → signal-chain IC, and they are the precision counterpart to delta-sigma ADCs that trade speed for resolution. Key features include 175 kSPS throughput per channel, ±10 V and 0 V-to-5 V input ranges, 4-channel analog input multiplexing, internal 2.5 V reference (also configurable for external reference), single-supply 5 V operation with low 12 mW typical power dissipation, and an on-chip output register that buffers the last conversion result. The wide-body 28-SOIC package delivers robust thermal performance and easy hand-solder-friendly lead pitch for industrial and instrumentation layouts. AC dynamic performance (SNR, SINAD) makes the part suitable for phasor measurement, vibration analysis, and closed-loop control loops where both channels must be sampled within a single conversion cycle. Fabricated in Analog Devices' Linear-Compatible CMOS (LC²MOS) process, the AD7863ARZ-2REEL pairs precision bipolar analog front-ends with low-power CMOS logic to achieve the simultaneous-sampling behavior of a sample-and-hold subsystem on a single die, removing the need for external track/hold circuitry. The high-speed parallel interface also supports asynchronous conversion starts and provides a BUSY output plus an EOC (end-of-conversion) flag, simplifying host-microprocessor or DSP handshaking. The on-chip reference (with buffered output to VREF) eliminates an external reference component in many designs. Typical applications include 3-phase motor current and voltage sensing for variable-frequency drives, power-line phasor measurement and protective relays, multi-axis industrial data-acquisition front-ends, sonar and acoustic beam-forming front-ends, and vibration monitoring on rotating machinery. Simultaneous-sampling behavior is essential wherever phase relationships carry information - the AD7863ARZ-2REEL's 5.2 μs conversion time keeps channel-to-channel skew in the sub-microsecond regime, well within the timing budgets of 50/60 Hz power-system and 1-10 kHz motor-control loops. Design tip: when using the internal 2.5 V reference, place two 0.1 μF ceramic decoupling capacitors as close as possible to the VREF and AGND pins to minimize reference-noise coupling into the conversion result. When using an external reference, choose a low-noise, low-drift source such that reference noise does not become the limiting factor on the ADC's ac performance. This page synthesizes distributor pricing tiers, drop-in alternatives, and engineering design guidance drawn from the Analog Devices AD7863 datasheet and the real-world purchasing data on DigiKey, Mouser, and Octopart - information not bundled in any single manufacturer document.

RFQ پەیوەندی
AD7865BSZ-2 - 14-Bit 4-Ch Simultaneous-Sampling 350kSPS ADC | ADI
AD7865BSZ-2

AD7865BSZ-2 - 14-Bit 4-Ch Simultaneous-Sampling 350kSPS ADC | ADI

The Analog Devices AD7865BSZ-2 is a fast, low-power, four-channel simultaneous-sampling 14-bit successive-approximation analog-to-digital converter (SAR ADC) in a 44-pin MQFP (10x10 mm) package. It operates from a single +5 V supply, integrates four track-and-hold amplifiers, an internal 2.5 V reference, an on-chip clock oscillator, and a high-speed parallel interface, and is specified at 350 kSPS per channel with a 2.4 µs successive-approximation conversion time per channel. The "-2" variant of the AD7865 family is configured for bipolar analog input ranges of ±5 V or ±10 V (HW/SW-selected) to interface directly with industrial ±10 V signal chains without external level shifting. A SAR (successive-approximation register) ADC is a type of Nyquist-rate converter that resolves one bit per clock cycle using an internal binary-search algorithm against a precision DAC; compared with delta-flush, flash, or pipeline ADCs, SAR converters are favored when high absolute DC precision, low latency, and low power dissipation must coexist. As a member of the broader data-converter category, the AD7865 belongs to the simultaneous-sampling ADC class used where multiple signals must be digitized at exactly the same instant - critical for phase-sensitive power, motor-control, and instrumentation applications. The simultaneous-sampling architecture eliminates the inter-channel phase error that plagues multiplexed-input ADCs in multi-phase systems. The AD7865BSZ-2 achieves 14-bit no-missing-code performance with 0.35 µs track-and-hold acquisition time, 80 dB SNR at 50 kHz input, and HW/SW-selectable bipolar input ranges (±5 V / ±10 V). The on-chip 2.5 V reference eliminates an external precision reference, and the high-speed parallel interface supports direct connection to DSPs, microcontrollers, and FPGAs. Compared with multiplexed multi-channel ADCs, the four simultaneous track-and-hold amplifiers preserve phase relationships between channels, which is essential for vector measurements in power-control loops and three-phase motor drives. Typical applications include three-phase motor control and inverter feedback, multi-axis industrial servo systems, simultaneous AC-line voltage and current monitoring, data-acquisition front ends for ±10 V industrial signal chains, power-quality and power-metering analyzers, and vibration/acoustic instrumentation. The wide bipolar input range allows direct digitization of industrial ±10 V signals without external signal conditioning. When designing with the AD7865BSZ-2, place the recommended 0.1 µF and 10 µF decoupling capacitors as close as possible to AVDD/DVDD pins to maintain SNR. The parallel interface may require external bus-isolation resistors when driving long PCB traces or backplanes. For system-level calibration, allow a 1 µs settling window between successive conversions and avoid driving the track-and-hold inputs beyond the absolute maximum ratings during fault events. This page synthesizes distributor pricing, drop-in AD7865-family alternatives, and practical design notes not found in the manufacturer datasheet, all aligned to the 2026-10-06 reference date.

RFQ پەیوەندی
AD7865YSZ-1 - 14-Bit 350kSPS Quad Simultaneous-Sampling ADC | ADI
AD7865YSZ-1

AD7865YSZ-1 - 14-Bit 350kSPS Quad Simultaneous-Sampling ADC | ADI

The Analog Devices AD7865YSZ-1 is a 14-bit, 350 kSPS, 4-channel simultaneous-sampling successive approximation register (SAR) analog-to-digital converter in a 44-pin MQFP (10x10 mm) package, supplied from a single +5 V rail. The -1 input variant accepts ±10 V or 0 V to +5 V bipolar input ranges, with hardware or software channel selection and a per-channel throughput of 2.4 µs conversion time (≈380 kSPS aggregate when channels are multiplexed). What is a simultaneous-sampling SAR ADC? A simultaneous-sampling ADC integrates one track-and-hold amplifier per channel so that all four input signals are captured at exactly the same instant; this preserves phase relationships in multi-phase systems such as three-phase motor control or four-quadrant power monitoring. SAR architecture delivers deterministic latency and no pipeline delay, which makes the AD7865 well suited to closed-loop control where conversion determinism is critical. The device integrates four track/hold amplifiers, a 2.5 V on-chip reference, an on-chip clock oscillator, signal-conditioning input scalers, and a high-speed parallel microprocessor-compatible interface. Hardware or software selection of input channels (VIN1..VIN4) lets the user convert all four channels simultaneously, or sequence through them under software control. Power consumption is typically 115 mW at full throughput, dropping under software power-down for portable or battery-backed applications. Typical applications include AC motor control and three-phase power metering, data acquisition systems for industrial process control, multiphase vibration and inertial measurement, instrumentation and medical imaging front-ends, and any multi-channel control loop where phase coherence between channels is required. The wide ±10 V input range also suits direct connection to current shunts and transducer bridges after scaling. When designing with this part, observe the analog input common-mode and ESD handling rules in the AD7865 datasheet, keep the analog/digital grounds separated at a single point, and respect the 44-MQFP thermal envelope when operating at the full 350 kSPS throughput at elevated ambient temperatures.

RFQ پەیوەندی
AD7872AN - 14-Bit 83 kSPS Sampling ADC | Analog Devices
AD7872AN

AD7872AN - 14-Bit 83 kSPS Sampling ADC | Analog Devices

The Analog Devices AD7872AN is a complete 14-bit successive-approximation analog-to-digital converter (SAR ADC) with a maximum throughput of 83 kSPS, housed in a 16-pin PDIP (N-16) through-hole package. The device integrates a track/hold amplifier, 14-bit ADC core, voltage reference, and three digital interface options - parallel, byte-wide, and serial - making it a drop-in solution for data-acquisition systems that previously required several discrete components. A SAR ADC (Successive-Approximation Register ADC) is a type of precision analog-to-digital converter that converts an input voltage to a digital code by sequentially comparing it against a precision reference using a binary search. SAR ADCs sit in the broader product hierarchy of ADC -> data converter -> mixed-signal IC -> semiconductor, and are favored for applications needing high DC accuracy and deterministic latency with no pipeline delay, in contrast to sigma-delta or pipeline architectures. Key features of the AD7872AN include 80 dB SNR at 10 kHz input frequency, 57 ns data-access time, ±5 LSB maximum integral nonlinearity (INL), bipolar ±10 V or unipolar 0 to +10 V input range (software configurable), and 50 mW typical power dissipation. The part uses Analog Devices' proprietary LC2MOS mixed-technology process and is specified for both DC accuracy and dynamic performance. Architecturally, the device combines a low-noise input amplifier, a buried Zener voltage reference, and a successive-approximation register with a precision DAC on a single die. The bipolar input stage uses a proprietary chopping technique that keeps integral linearity error below ±5 LSB over the industrial temperature range, while the high-speed comparator enables the 57 ns data-access time needed for high-speed parallel interface designs. Typical applications include industrial process control, instrumentation, spectrum analysis, and DSP front-ends. The wide input range and bipolar capability also suit motor-control current sensing and high-accuracy data-acquisition front-ends where a complete single-chip ADC with on-chip reference simplifies the BOM. Design consideration: the input signal source impedance should be kept below 1 kohm to avoid conversion errors caused by the input amplifier's bias current; add a 100 ohm series resistor with a 10 nF input capacitor for wideband noise filtering on high-impedance sensors. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ پەیوەندی
AD7873ARQZ - 12-Bit Touch Screen Digitizer ADC | Analog Devices
AD7873ARQZ

AD7873ARQZ - 12-Bit Touch Screen Digitizer ADC | Analog Devices

The Analog Devices AD7873ARQZ is a 12-bit successive approximation analog-to-digital converter (SAR ADC) with a synchronous serial interface and integrated low on-resistance switches designed to drive 4-wire resistive touch screens. It operates from a single 2.2 V to 5.25 V supply and delivers a throughput rate of 125 kSPS, packaged in a 16-pin QSOP (RQ-16). A touch screen digitizer is a specialized mixed-signal IC that combines an analog-to-digital converter, an integrated voltage reference, low-impedance analog switches, and coordinate-measurement firmware support. It measures the X/Y position of a stylus or finger press on a resistive touch panel and reports it to the system processor through a digital interface. As part of the touchscreen controller IC family, the AD7873 sits between human-machine interface (HMI) sensors and the embedded microcontroller, removing the burden of analog switch sequencing and battery-monitor sampling from the host CPU. Key differentiating features of the AD7873ARQZ include on-chip temperature sensing to +85 °C, an on-chip 2.5 V reference, direct battery measurement (up to 6 V), and touch-pressure measurement. The low on-resistance switches (typically less than 100 ohm) ensure accurate ratiometric measurement across the resistive touch panel without external multiplexer components, while the synchronous serial interface simplifies connection to common microcontrollers and DSPs. Architecturally, the AD7873 uses a classic SAR conversion core with a capacitive-charge redistribution DAC, a track-and-hold front end, and an integrated 2.5 V bandgap reference. The device enters a low-power shutdown mode between conversions, controlled by the serial interface, which is essential for battery-powered handheld devices where average current draw directly impacts runtime. Ratiometric conversion mode uses VCC as the reference for touch position measurements, eliminating absolute reference drift errors. Typical applications include resistive touch screen interfaces for PDAs, handheld instruments, point-of-sale terminals, industrial HMI panels, and battery-powered portable data entry devices. The integrated battery and temperature monitoring channels extend usefulness into multi-parameter handheld designs. When designing the input, ensure shutdown input current decays at all temperature ranges; debounce the pen-down input via software; use 0.1 uF ceramic bypass capacitors on VCC to suppress ADC switching transients; route the four touch-panel analog lines symmetrically to preserve measurement linearity. This page synthesizes distributor pricing, same-package drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

RFQ پەیوەندی
AD7875LPZ-REEL - 12-Bit 100kHz Sampling ADC | Analog Devices
AD7875LPZ-REEL

AD7875LPZ-REEL - 12-Bit 100kHz Sampling ADC | Analog Devices

The Analog Devices AD7875LPZ-REEL is a complete monolithic 12-bit analog-to-digital converter (ADC) with on-chip track-and-hold amplifier, internal reference, and parallel/byte/serial digital interface, sampling at 100 kSPS in a 28-pin PLCC (LCCC, MO-047AB, LCC-28) package. An ADC (analog-to-digital converter) is a mixed-signal integrated circuit that converts continuous analog voltages into discrete digital codes, enabling microcontrollers, DSPs, and processors to interpret real-world signals. The AD7875 belongs to the successive-approximation-register (SAR) ADC category, which uses an iterative binary-search algorithm with an internal DAC to perform each conversion in a fixed number of clock cycles. SAR ADCs sit within the broader data-converter family, alongside delta-sigma and pipeline architectures, and are favored for multi-channel multiplexed and DC/front-end signal acquisition where deterministic latency and low latency are critical. Key features include a 2 µs acquisition track-and-hold front end, 8 µs A/D conversion time, on-chip 2.5 V buried-zener reference laser-trimmed for accuracy, 72 dB SNR at 10 kHz input, ±5 V dual analog supply operation, and three interface modes (12-bit parallel, 8-bit byte, and serial). The 28-terminal J-lead surface-mount package (QCCJ / PLCC) is rated for the commercial 0 °C to +70 °C temperature grade and ships in tape-and-reel format for high-volume assembly. Architecturally, the AD7875 integrates an analog input multiplexer/amplifier, the SAR core, internal reference, clock oscillator, and a flexible digital interface on a single CMOS die. The laser-trimmed buried-zener reference and clock remove two of the largest external bill-of-materials items typical of discrete 12-bit ADC designs, shrinking PCB area and improving long-term gain stability. Typical applications include industrial process control front ends, multichannel data-acquisition boards, motor-control feedback loops (shaft position, current sense), and instrumentation signal inputs where 12-bit resolution and 100 kSPS throughput are sufficient. The on-chip reference also makes the part attractive for portable or space-constrained designs where an external reference would be impractical. When designing with the AD7875, choose the supply range carefully: ±5 V supplies yield best SNR at the expense of higher power dissipation, while ±3 V operation reduces power at slightly lower dynamic performance. Decouple both AVdd and DVdd pins with 0.1 µF ceramic capacitors placed within 5 mm of the package to keep digital switching noise out of the analog front end. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not available in the bare manufacturer datasheet, providing engineers with a single reference point for sourcing and second-sourcing decisions.

RFQ پەیوەندی
AD7876BR-REEL - 12-Bit 100kHz SAR ADC, 24-SOIC | Analog Devices
AD7876BR-REEL

AD7876BR-REEL - 12-Bit 100kHz SAR ADC, 24-SOIC | Analog Devices

The Analog Devices AD7876BR-REEL is a complete 12-bit successive-approximation analog-to-digital converter (ADC) with on-chip track-and-hold, on-chip reference, and parallel/byte/serial digital interface options, housed in a 24-pin SOIC wide-body package. An SAR (Successive Approximation Register) ADC is a type of analog-to-digital converter that uses a binary search algorithm and an internal capacitive DAC to convert an analog input voltage into a digital code over a fixed number of clock cycles. The AD7876 belongs to the broader data-converter hierarchy: ADC -> data converter -> signal chain IC -> mixed-signal semiconductor. Built on Analog Devices' LC2MOS process, it integrates the entire signal path from analog input to digital word in a single IC, eliminating the external components required by older discrete ADC designs. Key features include a 100 kHz throughput rate, 2 microsecond track-and-hold acquisition time, 8 microsecond ADC conversion time, an on-chip buried-Zener reference laser-trimmed for accuracy, and 72 dB signal-to-noise ratio. The device supports bipolar input ranges of +/-5 V or +/-10 V via the AD7876BR (BR suffix) and offers parallel, byte, and serial interface modes for flexible microcontroller or DSP connectivity. Operating from a single +5 V supply, it consumes approximately 70 mW of power. The AD7876 uses a charge-redistribution switched-capacitor DAC architecture combined with a precision comparator and SAR logic to perform successive approximation. The internal reference and clock eliminate two of the most critical external components in ADC subsystems, reducing board area and improving long-term stability. Dynamic performance is specified for DSP users with SNR and harmonic distortion figures that make it suitable for both DC measurement and AC signal acquisition applications. Typical applications include industrial process control and data acquisition, motor control feedback loops, instrumentation and test equipment, medical instrumentation signal conditioning, and spectrum analysis front-ends. The wide input range and integrated reference make it well suited for industrial 4-20 mA loop digitization with appropriate signal conditioning. When designing with this device, decouple the +5 V supply with a 10 uF tantalum and 0.1 uF ceramic capacitor placed close to the supply pin. The analog input drive amplifier must settle within the 2 us acquisition window to avoid conversion errors. For best noise performance, keep digital and analog grounds separated and joined at a single star point near the ADC. This page synthesizes distributor pricing from 6 sources, drop-in alternatives from the Analog Devices AD787x family and pin-compatible cross-brand parts, and practical design notes not consolidated on any single datasheet or distributor page.

RFQ پەیوەندی
AD7876CR-REEL - 12-Bit 100kHz Sampling ADC | Analog Devices
AD7876CR-REEL

AD7876CR-REEL - 12-Bit 100kHz Sampling ADC | Analog Devices

The Analog Devices AD7876CR-REEL is a complete 12-bit successive-approximation analog-to-digital converter (SAR ADC) with on-chip track-and-hold amplifier and 2.5 V on-chip reference, sampling at up to 100 kHz and housed in a 24-pin SOIC (RW) wide-body package delivered on 13-inch reels. What is a successive-approximation ADC? An SAR ADC is a precision data converter that performs a binary search across an internal capacitive DAC to digitize an analog input, settling one bit per conversion clock. The SAR architecture sits in the converter hierarchy between flash ADCs (fastest, lowest resolution) and sigma-delta ADCs (highest resolution, slowest). The AD7876 belongs to the broader category of data converters / signal chain ICs, specifically the precision mid-speed sampling ADC segment used in industrial, instrumentation and DSP front-ends. Key features of the AD7876 include a 2 µs acquisition track-and-hold amplifier, an 8 µs successive-approximation ADC core, ±10 V input range with overvoltage protection, and parallel (8/12-bit), byte, and serial digital interface options. The part delivers 72 dB SNR at a 10 kHz input and is fully specified for dynamic DSP parameters including signal-to-noise ratio, harmonic distortion and intermodulation distortion. Internal laser-trimmed scaling resistors and reference settle to within ±1 LSB. Architecturally, the AD7876 integrates a bipolar input front-end (resistor-scaled ±10 V), input protection clamps, the track/hold, the 2.5 V buried-Zener reference, the SAR logic and clock oscillator, plus a flexible three-state digital output port. The -REEL suffix indicates the tape-and-reel packaging option for high-volume SMT assembly. Operating from +5 V (VDD) and -5 V (VSS) supplies, it draws approximately 15 mW of power. Typical applications include industrial process control loops, multi-channel data acquisition systems, precision instrumentation, DSP front-ends, motor control position feedback and portable battery-powered measurement equipment. The wide ±10 V input range and dynamic specifications make it particularly suited to digitizing signals after sensor conditioning. When designing with the AD7876, provide well-bypassed analog and digital supplies and route AGND and DGND as a star ground to the system analog ground. For best dynamic performance in DSP applications, refer to the manufacturer's recommended layout in the datasheet. This page synthesizes distributor stock and pricing, drop-in cross-reference alternatives, and practical design notes not found in the manufacturer datasheet alone.

RFQ پەیوەندی
AD7878JPZ-REEL - 12-Bit 100kHz SAR ADC | Analog Devices
AD7878JPZ-REEL

AD7878JPZ-REEL - 12-Bit 100kHz SAR ADC | Analog Devices

The Analog Devices AD7878JPZ-REEL is a complete 12-bit analog-to-digital converter (ADC) with a maximum throughput of 100 kHz, integrating a track/hold amplifier, voltage reference, 8-word FIFO, and DSP-compatible serial interface into a single IC. Housed in a 28-pin PLCC (11.51 x 11.51 mm) plastic leaded chip carrier package, this successive-approximation-register (SAR) ADC operates from a single +5 V analog supply and a -5 V to -3 V negative supply, accepting bipolar input ranges of ±3 V or ±10 V (depending on configuration). According to the Analog Devices AD7878 datasheet, the converter delivers 2 microsecond acquisition time and 7 microsecond conversion time, with input voltage tolerance up to ±3 V as documented in the verified supplier listings. A successive-approximation-register ADC is a converter architecture that resolves one bit per clock cycle using an internal binary-weighted capacitor network and a comparator, then a digital-to-analog converter (DAC). This topology delivers deterministic latency, excellent DC accuracy, and inherently anti-alias-friendly sampling, making it preferred for multiplexed data-acquisition systems, motor-control feedback loops, and DSP front-ends where latency must be bounded. Within the broader converter hierarchy, SAR ADCs sit between flash converters (fastest, lowest resolution) and sigma-delta ADCs (highest resolution, lowest bandwidth), with the AD7878 occupying the high-speed 12-bit niche favored in industrial control and instrumentation. Key features of the AD7878JPZ-REEL include: 8.3 kSamples/sec nominal throughput (per third-party spec sheet), 2 us track/hold acquisition time, 7 us conversion time, internal 3 V Zener reference, 8-word FIFO buffer for DSP handshake efficiency, and on-chip DSP-compatible serial interface logic. The LC2MOS (Linear Compatible CMOS) process combines precision bipolar analog stages with low-power CMOS digital logic, enabling the integrated DSP-ready interface without external glue logic. The commercial temperature grade (0 C to +70 C) suits indoor industrial, instrumentation, and laboratory equipment. Typical applications span process-control front-ends, multiplexed data-acquisition systems, DSP-input signal chains, motor-control position feedback, and laboratory instrumentation. The on-chip FIFO is particularly valuable when the host processor (DSP or microcontroller) cannot service every conversion interrupt; the 8-word depth absorbs timing jitter and reduces interrupt overhead. When designing with this part, ensure both +5 V (VDD) and -5 V (or -3 V) negative supplies are decoupled with 0.1 uF ceramic capacitors placed within 5 mm of the supply pins, and observe the maximum throughput vs. acquisition/conversion timing budget described in the datasheet timing section. The bipolar input requires input-signal conditioning to scale within the ±3 V (default) or ±10 V (with attenuation) input range. This page synthesizes distributor pricing, drop-in same-package alternatives, and PCB-level design guidance not found in the bare manufacturer datasheet, with parameters sourced from Analog Devices, DigiKey, Mouser, Octopart, and third-party spec repositories as of 2026-10-12.

RFQ پەیوەندی
AD7878KPZ-REEL - 12-Bit 100kHz SAR ADC, DSP Interface | Analog Devices
AD7878KPZ-REEL

AD7878KPZ-REEL - 12-Bit 100kHz SAR ADC, DSP Interface | Analog Devices

The Analog Devices AD7878KPZ-REEL is a 12-bit successive-approximation analog-to-digital converter (SAR ADC) with a 100 kHz sampling rate, packaged in a 28-pin PLCC (J-Lead) form factor supplied on tape and reel. It integrates a track-and-hold amplifier with 2 µs acquisition time, the SAR core, an on-chip 3 V Zener reference, and an 8-word deep FIFO plus DSP interface logic in a single LC2MOS mixed-technology die. Operating from ±5 V analog supplies (or +5 V only with -5 V derived), the device delivers 72 dB signal-to-noise-plus-distortion ratio across commercial 0 °C to +70 °C ambient temperatures. A SAR ADC is a successive-approximation register analog-to-digital converter, a class of precision data converter that uses a binary-search algorithm and an internal precision DAC to compare the sampled input against successively halved reference voltages. SAR ADCs sit within the broader hierarchy of ADC architectures (SAR -> Nyquist-rate ADC -> data converter -> mixed-signal IC -> semiconductor), and are favored for applications that demand deterministic latency, no pipeline delay, and excellent DC accuracy in multiplexed or single-channel measurement front ends. Differentiating specifications include a 2 µs track-and-hold acquisition window, 7 µs A/D conversion time, 8-word FIFO buffer that decouples the DSP from sample timing, and DSP-port glue logic that lets the converter stream samples directly into Blackfin, SHARC, or TMS320-family processors with minimal host overhead. The LC2MOS process combines low-noise precision bipolar analog blocks with low-power CMOS digital logic, yielding the accuracy of bipolar ADCs at CMOS power levels. Architecturally, the AD7878 combines a switched-capacitor input stage, a charge-redistribution DAC array, a successive-approximation register, and an asynchronous DSP-compatible parallel/serial port. The internal Zener reference eliminates an external reference component, simplifying BOM while keeping gain error within calibration limits. Designers use the AD7878 when deterministic 100 kHz throughput, FIFO-buffered DSP streaming, and an integrated reference are all required simultaneously. Typical applications span industrial process-control front ends, motor-control current/voltage sensing, multi-channel data-acquisition boards for DSP-based systems, sonar and audio front ends, portable instrumentation, and embedded measurement modules. The 28-pin PLCC package is a JEDEC-standard plastic-leaded chip-carrier footprint compatible with widely available sockets and SMT assembly processes. When laying out a board, route the analog inputs as differential microstrip with a solid ground pour, place the 0.1 µF +VCC and -VCC bypass capacitors within 5 mm of the supply pins, and keep the digital DSP-port traces short and impedance-controlled to avoid coupling noise back into the analog front end. This page synthesizes distributor pricing, drop-in 12-bit SAR alternatives, application-specific design notes, and compliance information not bundled together on the manufacturer datasheet, giving engineers a single decision-ready reference for the AD7878.

RFQ پەیوەندی
AD7878LN - 12-Bit 100kHz ADC with DSP Interface | Analog Devices
AD7878LN

AD7878LN - 12-Bit 100kHz ADC with DSP Interface | Analog Devices

The Analog Devices AD7878LN is a complete 12-bit, 100 kHz sampling analog-to-digital converter (ADC) with an integrated 8-word FIFO and DSP interface, housed in a 28-pin PDIP (N-28) through-hole package. It integrates a track-and-hold amplifier with 2 microsecond acquisition time, a 7 microsecond successive-approximation ADC core, a 3 V internal Zener reference, and the FIFO plus control logic for direct connection to high-speed DSP processors. The part achieves 72 dB SNR at 10 kHz input and is specified over the commercial 0 to +70 C temperature range, making it a classic LC2MOS data-acquisition front end. A successive-approximation register (SAR) ADC is a deterministic, sample-by-sample converter that compares the held input against an internal binary-weighted DAC using a precision comparator. SAR ADCs deliver deterministic latency, no pipeline delay, excellent DC linearity, and inherently strong anti-alias behavior when paired with an external analog filter, which is why they remain the preferred topology for multiplexed data-acquisition systems and DSP front ends where each conversion result must arrive on a known clock edge. Key features of the AD7878LN include 12-bit resolution with no missing codes, a maximum 100 kHz throughput, integrated track/hold with 2 microsecond acquisition, on-chip 3 V reference, an 8-word deep FIFO that decouples conversion timing from DSP read timing, and a DSP-friendly parallel interface. The wide digital host compatibility spans the ADSP-2100, TMS320, and DSP56000 families, allowing the part to drop into a range of signal-processing designs without glue logic. The device operates from a single +5 V analog supply plus a separate +5 V digital supply, providing isolation between the analog input chain and the noisy DSP bus. The architecture minimizes digital feedthrough into the analog front end and supports unipolar 0 to +5 V input ranges, simplifying signal conditioning for transducer and process-control signals. Typical applications include DSP-based data acquisition front ends, process control and industrial instrumentation, motor control feedback sampling, multiplexed analog input subsystems, and portable or bench-top test equipment that requires deterministic 100 kHz sampling with a fast DSP read path. The integrated FIFO is particularly valuable when the DSP must service interrupts or run real-time algorithms without losing samples. When designing with the AD7878LN, allocate board area for a 1 microfarad decoupling cap on each analog supply pin and place the analog input trace away from the parallel digital bus to limit coupling. Because the part is a through-hole 28-pin PDIP, it is best suited for prototype, instrumentation, and legacy industrial designs rather than high-density SMT assemblies; for SMT equivalents in the same family see the alternatives section.

RFQ پەیوەندی
AD7887ARZ-REEL - 12-Bit 125kSPS 2-Ch SAR ADC | Analog Devices
AD7887ARZ-REEL

AD7887ARZ-REEL - 12-Bit 125kSPS 2-Ch SAR ADC | Analog Devices

The Analog Devices AD7887ARZ-REEL is a 12-bit successive-approximation-register (SAR) analog-to-digital converter (ADC) capable of 125 kSPS throughput from a single 2.7 V to 5.25 V supply. It offers 1 or 2 analog inputs, an integrated 2.5 V internal reference, and a high-speed SPI/QSPI/MICROWIRE/DSP-compatible serial interface. The part is supplied in an 8-lead SOIC (0.154 inch, 3.90 mm body width) and ships in a 2,500-piece Tape & Reel package, marked with the Z (lead-free, RoHS) finish. An ADC is a data converter that maps a continuous analog input voltage onto a discrete binary codeword. The 12-bit resolution means each LSB equals the full-scale range divided by 4096 - giving ~0.024% of FS step size and enabling precise measurement of low-bandwidth signals such as sensor outputs, motor currents, and instrumentation front-ends. Within the broader converter family, SAR ADCs excel where low latency, deterministic sampling, and excellent DC linearity are required, sitting between flash (fastest, lowest resolution) and sigma-delta (highest resolution, slowest) architectures. Key features of the AD7887 include a 500 ns input track-and-hold acquisition window, single-ended sampling architecture, straight-binary output coding, and a low-power CMOS process that consumes only a few milliwatts at full throughput. The serial interface can be operated from a single 3 V or 5 V supply, and dual-/single-channel mode is selectable through the on-chip control register. Power-down modes between conversions further reduce quiescent current to microamp levels, making the device attractive for battery and portable designs. Architecture-wise, the AD7887 combines a charge-redistribution DAC, a high-speed comparator, and an internal 2.5 V bandgap reference. The internal reference can be applied externally via the AIN1/VREF pin in single-channel mode, eliminating the need for an external reference IC and saving both cost and PCB area. Typical applications include industrial process control loops, portable and battery-powered instrumentation, motor-control current sense, optical sensor front-ends (e.g., photodiode signal conditioning), and general-purpose data acquisition in PLC and embedded systems. When designing with this device, bypass VDD with a 0.1 uF ceramic capacitor placed within 5 mm of the pin and keep the analog input trace short and guarded from digital switching nodes. The internal reference needs at least a 1 uF external decoupling capacitor on the REFCAP pin for the 2.5 V reference to settle within datasheet limits. This page synthesizes distributor pricing, pin-compatible drop-in alternatives, and practical PCB/thermal notes that go beyond the AD7887 datasheet standalone.

RFQ پەیوەندی
AD7888ARZ-REEL - 12-Bit 125kSPS 8-Ch Micropower ADC | ADI
AD7888ARZ-REEL

AD7888ARZ-REEL - 12-Bit 125kSPS 8-Ch Micropower ADC | ADI

The Analog Devices AD7888ARZ-REEL is a 12-bit, 8-channel, successive-approximation-register (SAR) analog-to-digital converter that operates from a single 2.7V to 5.25V supply and delivers up to 125 kSPS throughput in a 16-pin SOIC_N (R-16) surface-mount package, supplied on a 13-inch tape-and-reel. The part features eight single-ended analog inputs (AIN1 through AIN8), an on-chip 2.5V reference accessible at REF IN/REF OUT, and a high-speed serial interface compatible with SPI, QSPI, MICROWIRE, and most DSP serial ports. The input track-and-hold acquires a signal in 500 ns, supporting accurate sampling of fast-changing single-ended signals. An SAR ADC is a type of data converter that uses a binary-search successive-approximation algorithm to digitize an analog input, producing one sample per conversion cycle without the latency of pipelined or sigma-delta architectures. The AD7888 belongs to the SAR sub-family of analog-to-digital converters, which sits under the broader ADC category within data-converter ICs in the signal-chain block of mixed-signal systems. Low-power CMOS construction keeps typical dissipation at 2 mW during normal operation and only 3 uW in full power-down mode, making the part well-suited to battery-powered monitoring applications. Key features of the AD7888ARZ-REEL include a flexible reference arrangement (internal 2.5V reference or external 1.2V to VDD reference via the REF IN/REF OUT pin), a shutdown pin that drops quiescent current to microamp levels between conversions, and guaranteed operation over the -40C to +105C automotive-industrial temperature range. The wide supply range and simple SPI-compatible serial interface also ease integration with microcontrollers and DSPs that lack parallel ADC ports. Architecturally, the AD7888 uses a charge-redistribution DAC array with a sample-and-hold on each channel select, an internal oscillator that can be overdriven by an external clock for deterministic conversion timing, and automatic power-down between conversions to extend battery life. The 8 single-ended inputs share one ADC core, so channel switching is handled through the on-chip analog multiplexer; this keeps the package pin count to 16 while still serving multi-channel data-acquisition tasks. The serial interface supports daisy-chaining of multiple AD7888 devices for systems that need more than 8 channels. Typical applications include portable and battery-powered data acquisition, multi-channel sensor monitoring (temperature, pressure, strain, flow), industrial process control front ends, instrumentation and panel meters, and automotive sensor interfaces. Designers should pay particular attention to reference decoupling and analog-input filtering: place a 0.1 uF ceramic close to REF IN/REF OUT and a small RC network on each AIN to limit broadband noise that would otherwise degrade the converter's SNR. This page consolidates distributor pricing, 8-channel SAR alternative selections, and practical design notes that go beyond the manufacturer datasheet.

RFQ پەیوەندی
AD7888BR-REEL - 12-Bit 125 kSPS 8-Ch SAR ADC | Analog Devices
AD7888BR-REEL

AD7888BR-REEL - 12-Bit 125 kSPS 8-Ch SAR ADC | Analog Devices

The Analog Devices AD7888BR-REEL is a high-speed, low-power, 12-bit successive-approximation analog-to-digital converter (SAR ADC) that operates from a single 2.7 V to 5.25 V power supply. Packaged in a 16-pin SOIC and shipped on a 13-inch tape-and-reel carrier, this micropower ADC achieves a 125 kSPS throughput rate while consuming only 2 mW typical power at 3 V, with a power-down current of 1 µA. A SAR ADC is a type of analog-to-digital converter that uses a binary-search successive-approximation algorithm to digitize an analog input in N conversion cycles for an N-bit code. SAR ADCs sit within the broader hierarchy of data converters (ADC -> Nyquist-rate ADC -> SAR ADC -> mixed-signal IC -> semiconductor). They are valued for low-latency conversions, deterministic behavior, and excellent DC accuracy without pipeline delay, making them ideal for multiplexed channel sampling in embedded systems. Key features include 8 single-ended analog input channels (AIN1-AIN8), an input track-and-hold with 500 ns acquisition time, a serial interface compatible with SPI/QSPI/MICROWIRE/DSP, and an analog input range of 0 V to VREF. The AD7888 operates from a single supply and offers low power consumption, which makes it suitable for battery-powered and portable designs. The converter's throughput of 125 kSPS supports multichannel scanning applications such as sensor arrays and process control. The AD7888 uses an on-chip clock and reference input buffer; external VREF up to VDD is supported. The serial interface allows direct connection to most modern microcontrollers and DSPs without glue logic. The architecture also integrates channel-selection logic, so a single command initiates a conversion on the addressed channel and streams the 12-bit result. Typical applications include portable instrumentation, data acquisition systems, battery-powered monitoring, industrial process control, and sensor signal conditioning. The wide supply range (2.7 V to 5.25 V) simplifies integration with 3.3 V and 5 V MCUs. When designing with this part, place 0.1 µF decoupling capacitors close to AVDD and ensure the serial clock stays below the rated throughput to avoid data corruption. For multi-channel scanning, sequence channel switches between conversions to allow full settling of the input track-and-hold. This page combines verified distributor stock data, drop-in SOIC-16 alternative MPNs, and practical design guidance not always visible in the manufacturer datasheet, giving engineers a single reference for evaluation, sourcing, and PCB design.

RFQ پەیوەندی
AD7888BR-REEL7 - 12-Bit 125kSPS 8-Ch ADC SOIC-16 | ADI
AD7888BR-REEL7

AD7888BR-REEL7 - 12-Bit 125kSPS 8-Ch ADC SOIC-16 | ADI

The Analog Devices AD7888BR-REEL7 is a 12-bit successive-approximation analog-to-digital converter (ADC) offering 8 single-ended analog input channels, 125 kSPS throughput, and a serial SPI/MICROWIRE/QSPI-compatible interface, housed in a 16-pin SOIC_N package supplied on a 7-inch reel. It operates from a single 2.7 V to 5.25 V supply, includes an internal 2.5 V reference (or accepts an external REF input), and provides a power-down mode that drops supply current to under 1 µA for battery-aware designs. An ADC (Analog-to-Digital Converter) is a data-conversion IC that samples continuous analog voltage levels and translates them into discrete digital codes for microcontrollers, DSPs, or FPGAs. Within the converter hierarchy, the AD7888 sits in the SAR (successive-approximation register) sub-family of ADCs, characterized by deterministic latency and low power consumption compared to delta-sigma or pipeline architectures; it is itself part of the larger data-converter domain of mixed-signal ICs. Key features include a 500 ns input track-and-hold acquisition time, eight single-ended channels multiplexed to a single ADC core, a true analog input range of 0 V to VREF on each channel, daisy-chainable serial interface, and a hardware shutdown pin. The internal reference and channel sequencer reduce external component count, which is valuable in space-constrained sensor-interface PCBs. Technically, the AD7888 uses a charge-balancing DAC and a high-speed comparator inside its SAR loop to deliver 12-bit resolution without pipeline delay, making it well-suited to multiplexed applications that need deterministic per-channel conversion timing. Its low-power CMOS process keeps active current around 1 mA typical at full throughput. Typical applications include portable instrumentation, multi-channel sensor monitoring (temperature, pressure, strain-gauge bridges), battery-powered data loggers, and industrial process-control front ends where multiple slow-moving analog signals must be digitized by a single MCU. When designing with this device, ensure that the analog input pins are not driven above VDD or below GND, and add a 0.1 µF decoupling capacitor close to the supply pin to reduce digital-coupling noise on the analog sampling instant. This page synthesizes ADI-authorized datasheet data, current distributor pricing, and drop-in SOIC-16 cross-references so engineers can compare the AD7888 against modern pin-compatible ADCs in one place.

RFQ پەیوەندی
AD7890AN-2 - 8-Channel 12-Bit Serial ADC | Analog Devices
AD7890AN-2

AD7890AN-2 - 8-Channel 12-Bit Serial ADC | Analog Devices

The AD7890AN-2 is an 8-channel, 12-bit data acquisition system from Analog Devices, integrating an input multiplexer, an on-chip track/hold amplifier, a high-speed 12-bit ADC, a 2.5 V reference, and a high-speed serial interface. It operates from a single 5 V supply and accepts an analog input range of 0 V to 2.5 V for the -2 version. The device is packaged in a 24-pin PDIP (N) package, suitable for through-hole mounting in industrial and instrumentation applications. A data acquisition system (DAS) is a complete signal chain that samples multiple analog signals, converts them to digital words, and transfers the data to a host processor. The AD7890AN-2 combines the multiplexer, track/hold, ADC, reference, and serial interface in a single IC, simplifying board design and reducing component count. It is part of the broader family of analog-to-digital converters (ADCs) used in industrial control, data logging, and medical monitoring systems. Key features include a fast 12-bit ADC with a 5.9 µs conversion time, eight single-ended analog input channels, and a serial interface that supports SPI-compatible communication. The on-chip 2.5 V reference eliminates the need for an external reference, while the track/hold amplifier ensures accurate sampling of dynamic signals. The device also allows separate access to the multiplexer and ADC, providing flexibility in system design. Technically, the AD7890AN-2 uses a successive approximation register (SAR) architecture, which offers a good balance of speed and power consumption. The 117 kSPS sampling rate is suitable for multi-channel monitoring applications where each channel is sampled sequentially. The serial interface reduces pin count and simplifies isolation in industrial environments. The device operates over the industrial temperature range of -40°C to +85°C. Typical applications include industrial process control, data acquisition systems, battery monitoring, and medical instrumentation. The 0 V to 2.5 V input range is ideal for sensors with unipolar outputs, such as temperature and pressure transducers. The serial interface allows easy connection to microcontrollers and DSPs. When designing with the AD7890AN-2, ensure that the analog input signals are within the specified range and that the reference is properly decoupled. The serial clock should be limited to the maximum specified frequency to ensure accurate data transfer. Consider using a low-pass filter on each analog input to reduce aliasing.

RFQ پەیوەندی
AD7890ANZ-10 - 8-Channel 12-Bit Serial DAS | Analog Devices
AD7890ANZ-10

AD7890ANZ-10 - 8-Channel 12-Bit Serial DAS | Analog Devices

The AD7890ANZ-10 is an 8-channel, 12-bit serial data acquisition system (DAS) from Analog Devices, integrating an input multiplexer, an on-chip track/hold amplifier, a high-speed 12-bit ADC, a 2.5 V reference, and a high-speed serial interface. It operates from a single 5 V supply and accepts an analog input range of ±10 V for the -10 variant. The device is packaged in a 24-pin PDIP (ANZ suffix) and is designed for industrial temperature ranges from -40°C to +85°C. A data acquisition system (DAS) is a complete signal chain that samples multiple analog signals, converts them to digital, and interfaces with a microcontroller or DSP. The AD7890 integrates the multiplexer, track/hold, ADC, and reference into a single IC, simplifying design and reducing board space compared to discrete implementations. It belongs to the family of serial data acquisition systems, which are essential in industrial automation, process control, and instrumentation. Key features include a fast 12-bit ADC with 5.9 µs conversion time, eight single-ended analog input channels, and a serial interface compatible with SPI. The on-chip track/hold amplifier ensures accurate sampling of dynamic signals, while the internal 2.5 V reference eliminates the need for external reference circuitry. The multiplexer is independently accessible, allowing users to insert antialiasing filters or signal conditioning between the multiplexer and the ADC. The AD7890 uses LC2MOS technology, combining low power consumption with high-speed performance. The serial interface supports high-speed data transfer, and the device can be configured for various input ranges (0-2.5 V, 0-4.096 V, ±10 V) depending on the variant. The 24-pin PDIP package is suitable for through-hole assembly, providing ease of prototyping and robust mechanical connection. Typical applications include industrial process control, data logging, and multi-channel sensor monitoring. The AD7890ANZ-10 is ideal for systems requiring simultaneous sampling of multiple analog signals with 12-bit resolution and serial output for easy microcontroller interfacing. When designing with this device, ensure proper decoupling of the 5 V supply and careful layout of the analog input traces to minimize noise. The independent multiplexer access allows flexible signal conditioning, but the track/hold acquisition time must be considered for accurate sampling of high-frequency signals.

RFQ پەیوەندی
AD7890BR-4 - 8-Channel 12-Bit DAS | Analog Devices
AD7890BR-4

AD7890BR-4 - 8-Channel 12-Bit DAS | Analog Devices

The AD7890BR-4 is a complete, 8-channel, 12-bit data acquisition system (DAS) from Analog Devices, fabricated in LC2MOS technology. It integrates a fast 12-bit ADC with a 5.9 µs conversion time, an 8-channel multiplexer, an on-chip track/hold amplifier, and an on-chip reference. The device operates from a single 5 V supply and accepts an analog input range of 0 V to 4.096 V for the AD7890-4 variant. The multiplexer is independently accessible, allowing the user to insert an antialiasing filter or signal conditioning between the multiplexer and the ADC. The AD7890BR-4 is packaged in a 24-pin SOIC (narrow body) and communicates via a serial interface, making it ideal for industrial process control, data acquisition systems, and battery-powered instrumentation. A data acquisition system (DAS) is a complete signal chain that samples multiple analog signals, converts them to digital, and outputs the data to a processor. It typically includes a multiplexer, an ADC, a track/hold amplifier, and a reference. The AD7890BR-4 integrates these functions into a single IC, reducing board space and design complexity. In the hierarchy of signal chain components, a DAS sits above a standalone ADC, as it includes the multiplexer and reference, but below a full system-on-chip that might include a microcontroller. This integration is particularly valuable in multi-channel monitoring applications where space is constrained. Key features of the AD7890BR-4 include its 8 single-ended analog input channels, 12-bit resolution, and a serial interface that simplifies connection to microcontrollers and DSPs. The device offers a choice of input ranges: ±10 V (AD7890-10), 0 V to 4.096 V (AD7890-4), and 0 V to 2.5 V (AD7890-2). The on-chip track/hold amplifier ensures accurate sampling of fast-changing signals, while the on-chip reference eliminates the need for an external reference, saving cost and board area. The device operates over a temperature range of -40°C to +85°C, making it suitable for industrial environments. Technically, the AD7890BR-4 uses a successive approximation register (SAR) architecture, which provides a good balance of speed and resolution. The 5.9 µs conversion time corresponds to a maximum sample rate of approximately 117 kSPS when all channels are scanned sequentially. The serial interface is SPI-compatible, with a clock input and data output, allowing easy integration with most microcontrollers. The device also features a busy output that indicates when a conversion is in progress, simplifying synchronization. Typical applications include industrial process control, where multiple sensors need to be monitored; data acquisition systems for test and measurement; and battery-powered instrumentation, where the low power consumption and single-supply operation are advantageous. The AD7890BR-4 is also suitable for medical monitoring equipment and automotive test systems. When designing with the AD7890BR-4, ensure that the analog input signals are within the specified range and that adequate decoupling is provided on the power supply pins. The serial interface should be isolated if the system is subject to high noise, and the reference output should be buffered if driving external loads.

RFQ پەیوەندی
AD7892AR-1 - 12-Bit 500kSPS Bipolar SAR ADC | Analog Devices
AD7892AR-1

AD7892AR-1 - 12-Bit 500kSPS Bipolar SAR ADC | Analog Devices

The Analog Devices AD7892AR-1 is a 12-bit, 500 kSPS successive-approximation analog-to-digital converter (SAR ADC) in a 24-pin SOIC package with bipolar ±10 V (or 0 to +10 V) input range. It operates from a single +5 V supply, integrates an on-chip track/hold amplifier, an internal +2.5 V reference, and supports both serial and parallel interface modes, making the AD7892AR-1 a high-performance single-supply data-acquisition front end for industrial process controls and instrumentation. An ADC (analog-to-digital converter) is a data-converter integrated circuit that translates a continuous analog input voltage into a discrete digital code. Within the converter taxonomy, SAR (Successive Approximation Register) ADCs sit between high-speed flash ADCs and high-resolution delta-sigma ADCs, offering an attractive balance of speed (100 kSPS to multi-MSPS), resolution (12-18 bits), and low power. SAR converters are widely used in industrial control loops, motor-control current sensing, multichannel data-acquisition systems (DAS), and instrumentation where deterministic latency and excellent DC accuracy are required. Key headline specifications include 12-bit resolution, 500 kSPS throughput (1.47 µs conversion time using the internal clock), a single +5 V supply with bipolar ±10 V input range (selected via the R1 input), ±5 V or 0 V to +5 V alternative input options on other AD7892 grades, 60 dB typical SNR at 50 kHz input, low power dissipation of around 60 mW, and a parallel or serial digital interface. The bipolar input capability eliminates the need for external level-shift or negative-rail signal conditioning in many 4-20 mA, ±5 V sensor, and motor-current applications. The AD7892AR-1 uses an LC²MOS process with an on-chip buried-zener reference trimmed to ±10 mV initial accuracy, ensuring 12-bit performance without external reference components. The integrated track/hold amplifier handles input signals up to several hundred kHz, and the successive-approximation conversion delivers zero-pipeline latency, which simplifies closed-loop and oversampling applications. Typical applications for the AD7892AR-1 include industrial process control (4-20 mA loop digitization), AC motor-control current and voltage sensing, instrumentation and data-acquisition systems, battery-cell monitoring, and CCD image processing. The combination of bipolar input and single +5 V supply simplifies analog front-end designs. When designing with the AD7892AR-1, pay close attention to the input-protection network - a small series resistor and clamping diodes limit fault currents during over-voltage transients, as recommended in the AD7892 datasheet. Buffer the signal source with a low-impedance driver to preserve AC performance at high input frequencies. This page synthesizes distributor pricing, drop-in package-compatible alternatives, and design notes for the AD7892AR-1 that go beyond the manufacturer datasheet, including cross-brand Bipolar SAR ADC equivalents and same-grade ADI AD7892 family pin-compatibles.

RFQ پەیوەندی
AD7892AR-1REEL - 12-Bit 500kSPS SAR ADC | Analog Devices
AD7892AR-1REEL

AD7892AR-1REEL - 12-Bit 500kSPS SAR ADC | Analog Devices

The Analog Devices AD7892AR-1REEL is a 12-bit, 500 kSPS successive-approximation analog-to-digital converter that operates from a single +5 V supply and is offered in a 24-pin SOIC wide-body package (tape and reel packaging). The part integrates a 1.47 µs SAR ADC core, an on-chip track/hold amplifier, an internal +2.5 V reference, and versatile serial/parallel interface logic, enabling direct connection to microcontrollers, DSPs, and high-speed data acquisition ASICs. An ADC (analog-to-digital converter) is a mixed-signal semiconductor that translates real-world analog voltages into discrete digital codes for processing by microcontrollers, DSPs, or FPGAs. Within the data-converter hierarchy, SAR (successive-approximation register) ADCs sit between flash converters and sigma-delta ADCs in speed and resolution: they offer 8-18 bits of resolution with 0.1-10 MSPS throughput and low latency, making them the workhorse for multiplexed control loops, instrumentation, and motor control. The AD7892 family belongs to this SAR category and is further classified as a bipolar-input, single-supply precision ADC for industrial measurement applications. Key specifications include 12-bit resolution (no missing codes), 500 kSPS throughput (the AD7892-1 grade; the AD7892-3 grade reaches 600 kSPS), bipolar ±5 V or ±10 V analog input range, ±5 V single-supply operation, internal 2.5 V reference, and 1.47 µs ADC conversion time. The 24-pin SOIC wide-body package offers 0.295 inch (7.50 mm) body width and operates from -40 °C to +85 °C ambient, suitable for industrial environments. Architecturally, the converter combines a high-speed comparator, charge-redistribution DAC array, and successive-approximation register clocked from an internal oscillator. The on-chip track/hold front-end settles in ~150 ns, allowing full throughput at the rated 500 kSPS without external buffering for many sensor signals. Typical applications include industrial process control, motor control feedback loops, multi-channel data acquisition systems, instrumentation front-ends, and precision transducer signal conditioning. Design engineers select the AD7892-1 when bipolar input range and single-supply operation are required in a compact analog front-end.

RFQ پەیوەندی
AD7892ARZ-2REEL - 12-Bit 500kSPS Single-Supply ADC | ADI
AD7892ARZ-2REEL

AD7892ARZ-2REEL - 12-Bit 500kSPS Single-Supply ADC | ADI

The Analog Devices AD7892ARZ-2REEL is a 12-bit successive-approximation analog-to-digital converter operating from a single +5 V supply with a 500 kSPS throughput rate, housed in a 24-pin SOIC wide-body package supplied on a 7-inch reel. The AD7892 integrates a 1.47 µs SAR ADC core, an on-chip track-and-hold amplifier, an internal +2.5 V reference, and versatile parallel or serial interface logic on a single die, allowing system designers to replace multi-chip discrete ADC solutions with one compact part. The AD7892-2 variant specified by the -2 speed grade pin straps its analog input range to either 0 V to VREF or ±10 V operation, with self-calibration on power-up providing ±1 LSB max linearity error. A successive-approximation register (SAR) ADC is a precision data converter that resolves an analog input to a digital code in N clock cycles using a binary-search algorithm. SAR ADCs are favored over delta-sigma and pipeline types when applications need deterministic latency, low latency per conversion, and excellent DC linearity at moderate-to-high sampling rates. Within the broader signal-chain hierarchy, the SAR ADC sits between general-purpose data converters and precision instrumentation; AD7892 specifically targets single-supply, low-power industrial and instrumentation systems where bipolar input ranges are required without a negative rail. Key features include 500 kSPS throughput in the -2 grade, 1.47 µs conversion time, on-chip +2.5 V reference with low drift, input range pin-strapping for 0-VREF or ±10 V operation, and 60 mW typical power dissipation from a single +5 V supply. Fabricated in ADI's LC2MOS process that mixes precision bipolar input stages with low-power CMOS logic, the AD7892 achieves low power without sacrificing analog input accuracy. Interface options include high-speed parallel or two-wire serial output, allowing the same silicon to serve memory-mapped microcontroller buses or low-pin-count DSP serial ports. Typical applications include industrial process control loops, portable battery-powered instrumentation, motor control current sensing, and DSP front-end data acquisition. The on-chip reference and single +5 V supply simplify system BOM and reduce PCB area, while the ±10 V input range option makes the part suitable for legacy ±12 V industrial signal paths when powered from a single +5 V rail via input attenuation. Designers should note that the -2 grade throughput is 500 kSPS versus the -3 grade's 600 kSPS, and the -1 grade offers single-ended rather than dual analog inputs. For thermal management, the 24-pin SOIC plastic package combined with 60 mW typical dissipation requires only standard PCB thermal practice. The internal reference decouples design effort from external reference selection; bypass with the recommended capacitor network per the datasheet to minimize conversion noise. The reel-packaged -REEL suffix denotes 7-inch tape and reel for high-volume SMT assembly. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the standalone manufacturer datasheet.

RFQ پەیوەندی
AD7892BR-1 - 12-Bit 500kSPS Bipolar ADC | Analog Devices
AD7892BR-1

AD7892BR-1 - 12-Bit 500kSPS Bipolar ADC | Analog Devices

The Analog Devices AD7892BR-1 is a 12-bit, 500 kSPS successive-approximation analog-to-digital converter that operates from a single +5 V supply. The part contains a 1.47 µs SAR ADC, an on-chip track/hold amplifier, an internal +2.5 V reference, and versatile parallel or serial interface structures for direct microprocessor connection. It is offered in a 24-pin SOIC wide-body (0.295", 7.5 mm) package and accepts bipolar analog input ranges including true bipolar ±10 V or ±5 V (model dependent) via the AD7892-1 input scaling network. What is a SAR ADC? A successive-approximation register analog-to-digital converter is a sampling data converter that performs bit-by-bit decision against an internal DAC to converge on the input voltage. In the broader taxonomy, the AD7892 sits as: ADC -> data converter -> signal chain IC -> mixed-signal semiconductor. SAR ADCs trade raw speed for deterministic latency and excellent DC accuracy, making them the dominant architecture for 12-/14-/16-bit precision instrumentation at sample rates from 100 kSPS to 10 MSPS. Key features include ±17 V overvoltage protection on analog inputs (AD7892-1/2/3 variants), single-supply +5 V operation, an on-chip 2.5 V reference (or external reference option), choice of parallel 12-bit word or serial data output formats, and low power consumption of approximately 60 mW typical at 500 kSPS. The bipolar input stage on AD7892-1 extends usable dynamic range for industrial transducer signals that swing around ground. Architecturally, the AD7892BR-1 combines a high-impedance input attenuator, a fast track/hold, the SAR core clocked by an internal oscillator, and an internal 2.5 V bandgap reference. The single-supply bipolar topology uses input resistor scaling and level shifting so that the internal ADC core always sees a 0 V to 2.5 V (or 0 V to 5 V) unipolar signal — a classic Analog Devices LC2MOS approach that predates modern pin-compatible CMOS ADCs. Typical applications include industrial process control data acquisition, motor control current/voltage sensing, instrumentation front-ends, and medical monitoring signal chains where bipolar ±10 V inputs must be digitized directly without external signal conditioning. It is also used in test-and-measurement equipment and DSP front-end digitization. When designing with the AD7892BR-1, ensure the analog input is properly buffered because the input attenuator presents a relatively high source impedance that interacts with sample-rate-dependent acquisition time. Decouple VDD with 10 µF tantalum in parallel with 100 nF ceramic placed within 5 mm of the supply pin; do not share digital and analog ground returns under the package. This page synthesizes distributor pricing and cross-reference findings not presented in the datasheet, focusing on practical guidance rather than parameter repetition.

RFQ پەیوەندی