ADC/DAC
بەرهەمەکان (3,600+)
AK4495SEQ - 32-Bit 2-Channel 768kHz DAC | Asahi Kasei
The Asahi Kasei Microdevices AK4495SEQ is a premium 32-bit, two-channel digital-to-analog converter designed for high-resolution audio, supporting PCM sampling rates up to 768 kHz and DSD playback. The device uses AKM VELVET SOUND architecture and provides a 126 dB signal-to-noise ratio in a 44-LQFP package measuring 10 mm by 10 mm. It is intended for audiophile digital sources, network streamers, USB-audio systems, CD transports, and balanced or single-ended analog output stages. A DAC is a digital-to-analog converter, a signal-conversion IC within the broader digital-to-analog converter, audio signal-processing, and semiconductor hierarchies. It receives digital audio samples from a source such as USB, S/PDIF, I2S, or a networked player and reconstructs the corresponding analog waveform. AKM's VELVET SOUND architecture is the technology family used by this converter to target high-fidelity audio reproduction with low distortion and high dynamic-range capability. The AK4495SEQ provides 32-bit resolution, two audio channels, PCM operation up to 768 kHz, and a stated dynamic range of 126 dB. These headline specifications make the converter relevant to designs that must preserve fine amplitude detail from high-resolution PCM sources. Its dual-channel architecture supports stereo audio, while the surface-mount LQFP package permits compact, manufacturable implementation on standard PCB assembly processes. Technical operation requires compatible digital audio data, a stable device supply, correctly configured control pins, and an external analog output stage. Digital data can be accepted through supported serial audio interfaces, while the converter's internal architecture and output characteristics determine the achievable signal integrity. Circuit performance therefore depends on clean reference connections, suitable supply decoupling, controlled clocking, balanced signal routing, and an output filter selected for the intended load and bandwidth. Typical applications include high-end network streamers, professional USB-audio interfaces, optical and coax digital-audio transports, multichannel studio monitoring, and premium home-audio products. The converter is particularly appropriate when a design requires 32-bit PCM processing, dual-channel output, and sampling rates above the conventional 192 kHz audio boundary. External balanced-output circuitry can preserve the converter's channel separation and common-mode advantages in differential-output implementations. The principal design consideration is that a high-resolution DAC does not automatically guarantee high system performance. Implement the manufacturer's recommended power, ground, clock, and digital-interface layouts, and validate output-filter and gain settings for the selected amplifier. Keep sensitive analog routing away from noisy switching nodes, and evaluate channel balance and distortion at the intended output level rather than relying only on headline converter specifications. This page organizes the exact AK4495SEQ technical identity, package information, application guidance, source links, and replacement constraints into a practical engineering reference. It also distinguishes confirmed drop-in alternatives from merely similar converters, helping designers avoid PCB rework while selecting an appropriate high-resolution audio DAC.
AK4497EQ - 32-Bit 2-Channel 128dB Audio DAC | AKM
The Asahi Kasei Microdevices AK4497EQ is a premium 32-bit stereo digital-to-analog converter with two channels, 128 dB dynamic range, support for 768 kHz DSD and PCM audio, and a 64-pin HTQFP package measuring 10 mm by 10 mm. The converter uses AKM's VELVET SOUND architecture, a technology associated with high-end audio equipment and designed for low-distortion signal conversion. A digital-to-analog converter, or DAC, is an integrated circuit that converts digital PCM or DSD audio data into continuous analog voltage signals for downstream amplifiers, headphones, or line-level equipment. The AK4497EQ belongs to the audio DAC family within the broader semiconductor and signal-conversion hierarchy. Its dual-channel architecture allows simultaneous left- and right-channel playback, while its high-resolution format support makes it suitable for premium audio systems that require faithful reproduction of digital recordings. The AK4497's defining feature is the VELVET SOUND architecture, which the manufacturer describes as delivering low distortion and wide dynamic range. The device also integrates an OSR Doubler switched-capacitor filter. According to the manufacturer description, this filter supports a wide range of input signals, lowers out-of-band noise, and helps reduce power consumption. These characteristics make the converter useful in designs where analog output purity and high-resolution playback are more important than a compact, low-cost audio implementation. The AK4497EQ supports 32-bit PCM audio and DSD playback up to 768 kHz. It is packaged in a 64-pin HTQFP surface-mount package with a 10 mm by 10 mm body. The package format provides a substantial thermal and routing footprint for a high-performance stereo converter, but it also requires a carefully designed PCB with adequate exposed-pad handling, clean analog grounding, and separation between digital and analog signal paths. Typical applications include premium desktop and portable DACs, network audio players, high-resolution headphone amplifiers, digital audio workstations, and consumer audio receivers requiring DSD support. The AK4497EQ is particularly appropriate when the system must accept high-rate digital formats while preserving a low-noise analog output stage. It is also suitable for custom audio platforms where the converter is paired with a high-quality output amplifier, analog filter, and precision clock source. For implementation, use the manufacturer's datasheet for the exact pin assignments, recommended application circuit, supported interface modes, clock requirements, and power-supply sequencing. Keep digital clock and data traces away from the analog output section, provide the specified bypass capacitors at the power pins, and route analog return currents without passing through digital return paths. This product page combines the manufacturer's AK4497EQ datasheet information with package, application, sourcing, and drop-in comparison guidance. It is designed to help engineers evaluate the AK4497EQ for high-resolution stereo DAC implementations while emphasizing the practical PCB and signal-integrity decisions that determine realized audio performance.
AK4499EQ - 32-Bit 4-Channel Audio DAC | Asahi Kasei
The Asahi Kasei Microdevices AK4499EQ is a premium switched-resistor, four-channel audio digital-to-analog converter with 32-bit resolution, PCM sampling rates from 8 kHz to 768 kHz, and DSD512 input support. The device is offered in a 128-pin HTQFP package measuring 14 mm by 14 mm. A DAC is a digital-to-analog converter that transforms PCM, DSD, or other digital audio samples into continuous analog voltage signals for amplification and loudspeaker reproduction. The AK4499EQ belongs to the broader digital-to-analog converter hierarchy and uses a switched-resistor architecture intended to provide low distortion and low noise in high-resolution audio equipment. The AK4499EQ supports four DAC channels and multiple digital audio interfaces, including PCM, DSD, and EXDF formats. Its maximum PCM rate is 768 kHz, while its maximum DSD rate is DSD512. These capabilities suit high-resolution network players, USB DACs, professional audio equipment, digital mixing consoles, and premium home-audio systems. Configuration is supported through I2C and 3-wire serial register control. The switched-resistor conversion architecture separates the conversion function from conventional current-source ladder behavior and is intended to improve linearity and reduce distortion. The manufacturer describes the device as a premium four-channel DAC aimed at applications where low distortion, low noise, and support for very high-resolution source material are priorities. Operation can be configured for use with internal LDO regulation or external analog supplies, providing flexibility in power-supply implementation. Typical implementations place the converter between a digital audio receiver such as AK4118 and a high-quality analog output stage. AK4499EX is associated with related AK4499-family designs, while AK4191EQ appears in architectures using an AKM digital interface and converter chipset. The four-channel structure also permits balanced or multichannel output arrangements when the surrounding circuitry supports the converter's channel organization. PCB design requires close attention to the exposed-pad package, analog and digital supply routing, and separation of high-speed digital interfaces from sensitive analog outputs. Place output capacitors and analog routing in accordance with the manufacturer reference layout, keep the exposed pad properly connected to the ground plane, and decouple each supply domain close to its pins. The 14 mm by 14 mm footprint makes thermal management and analog-layout planning more demanding than in a small QFN audio converter. This product page combines the manufacturer datasheet information with practical interface, application, package, and replacement guidance. It also distinguishes verified AK4499EQ characteristics from functional alternatives so engineers can determine whether a candidate is a true pin-compatible replacement or merely a different premium DAC architecture.
AK5330VM - 16-Bit Special-Purpose ADC | AKM Corporation
Asahi Kasei Microdevices AK5330VM is a 16-bit special-purpose data-conversion IC offered in a 28-pin SSOP package. It is categorized for ADC/DAC and data-acquisition applications, where its compact package supports high-density analog signal acquisition and precision signal-processing systems. The AK5330VM designation identifies the manufacturer’s 16-bit converter family in a surface-mount SSOP configuration. An ADC is an analog-to-digital converter, a semiconductor that transforms a continuous analog voltage into a digital code for processing, storage, measurement, or control. An ADC/DAC converter may also provide a digital-to-analog function for signal generation or test equipment. The AK5330VM belongs to the broader data-converter hierarchy, where specialized converters are selected according to resolution, channel requirements, sampling behavior, interface method, clocking, accuracy, and physical footprint. The principal confirmed characteristics of the AK5330VM are 16-bit converter resolution and a 28-pin SSOP package. Its special-purpose ADC/DAC positioning makes it relevant to precision signal-processing equipment, data-acquisition systems, and instrumentation requiring a compact multichannel mixed-signal converter. The SSOP form factor offers a practical board-space reduction relative to larger leaded packages while preserving a conventional surface-mount assembly process. The AK5330-VM listing identifies the converter technology as sigma-delta. Sigma-delta conversion is particularly useful in measurement systems because it shapes quantization noise and can provide high resolution without requiring a high-speed flash-type converter architecture. Its practical performance depends on the complete circuit configuration, including input bandwidth, clock frequency, digital filtering, reference voltage, decimation settings, and the accuracy of external analog components. AK5330VM is applicable to laboratory instrumentation, industrial monitoring, sensor-interface systems, audio and communications test equipment, and other acquisition platforms. Design selection should begin with the required resolution and signal bandwidth, then verify the converter’s timing, reference, interface, and channel architecture against the manufacturer’s datasheet before schematic capture. The same check is essential before designing a PCB footprint or replacing the part. A key assembly consideration is the 28-pin SSOP footprint. Place the device according to the manufacturer’s land pattern, preserve adequate clearance around adjacent components, and route the analog input, reference, clock, power, and digital interface sections with attention to their current paths. Input and reference networks should be physically separated from switching or high-current digital circuitry to reduce coupling into the measurement result. This product record combines the confirmed AK5330VM identity, 16-bit resolution, sigma-delta technology classification, 28-pin SSOP packaging, application guidance, comparison fields, and sourcing-oriented details. It also distinguishes the exact MPN from broader converter families so engineers can begin footprint and functional-compatibility checks with the correct device in scope.
AK5351VF - 20-Bit Stereo ADC | Asahi Kasei Microdevices
Asahi Kasei Microdevices/AKM AK5351VF is a 20-bit, two-channel, 64-times-oversampling delta-sigma analog-to-digital converter designed for stereo digital audio systems. It uses Enhanced Dual bit modulator architecture and is supplied in a 24-VSOP package. The converter supports simultaneous processing of two stereo-related input channels, while the 20-bit representation provides sufficient resolution for professional and consumer digital audio equipment. An audio ADC is an analog-to-digital converter optimized for capturing continuously varying audio waveforms. Within the signal-chain hierarchy, it converts left and right microphone, line, or playback signals into digital samples for transmission, storage, mixing, or further processing. The AK5351VF belongs to the ADC/DAC class of data-conversion integrated circuits, combining a delta-sigma modulator with digital decimation and stereo-channel processing. Its 64fs oversampling architecture places substantial filtering and noise-shaping requirements around the conversion process. The principal identified characteristics are 20-bit resolution, 64fs oversampling, and two audio channels. Enhanced Dual bit architecture is the converter’s defining implementation feature and is intended to provide a wider dynamic range while controlling the demands associated with delta-sigma conversion. These characteristics make the device relevant to audio capture and monitoring systems in which two-channel conversion is required and direct digital audio output is preferable to basic analog digitization. The AK5351VF is intended for stereo digital systems rather than general-purpose instrumentation. A typical signal path places one analog source on each conversion channel, followed by the converter’s digital interface and downstream audio processing. System designers must account for input bandwidth, analog front-end behavior, clock requirements, supported digital audio format, and power-supply cleanliness. Because the converter performs high-resolution oversampling, board-level grounding and decoupling remain important for preserving low-level audio fidelity. Typical applications include professional digital mixers, multichannel monitoring controllers, broadcast consoles, USB or FireWire audio interfaces, stereo recording equipment, and high-end consumer audio systems. Two-channel devices such as this ADC are especially useful where simultaneous left and right signal conversion is required. Systems requiring more than two channels will generally need additional converter instances or a multichannel audio-conversion architecture. For a new design, use the manufacturer datasheet pin-description table, electrical characteristics, and application circuit before assigning PCB nets. Pay particular attention to analog input routing, grounding, digital interface mode, master-clock relationships, and the treatment of unused inputs. The VF ordering code is associated with tape-and-reel production according to the listed product information. This page organizes the verified AK5351VF product facts into an engineering-oriented guide covering stereo ADC selection, application fit, interface considerations, and replacement evaluation. It also distinguishes a documented drop-in substitute from merely similar converters so that board-level compatibility is not inferred from resolution or channel count alone.
AK5352VF 20-Bit 96kHz Audio ADC | Asahi Kasei Microdevices
The Asahi Kasei Microdevices AK5352VF is a 20-bit audio analog-to-digital converter with a 96 kHz sampling rate in a 24-pin VSOP package. It is designed for high-fidelity audio and data-acquisition systems where compact conversion, low-noise signal capture, and multi-channel audio processing are important. The device uses an Enhanced Dual Bit delta-sigma modulator architecture and is supplied in tape-and-reel packaging. An ADC is a data-conversion IC that converts an analog audio voltage into a digital code for processing, storage, or transmission. Within the broader semiconductor hierarchy, the AK5352VF belongs to the ADC/DAC product family and ultimately serves as a signal-chain interface between analog audio circuitry and digital audio systems. Its 20-bit resolution supports substantially more quantization levels than an 8-bit converter, while the 96 kHz sampling capability targets professional and consumer digital-audio workloads. The AK5352VF combines a 20-bit conversion resolution with a maximum sampling rate of 96 kHz in a 24-pin VSOP package. The Enhanced Dual Bit delta-sigma architecture is intended to provide a wide dynamic range while retaining low-distortion characteristics. Its compact package also reduces board area compared with larger multi-pin converter packages, making the device suitable for space-constrained audio equipment. Audio performance depends on the complete signal path, including the analog input stage, reference voltage, clock source, grounding, decoupling, and digital data interface. Designers should treat the converter’s specified input range, analog and digital supply voltages, clock requirements, and digital output format as constraints for the surrounding circuit. The delta-sigma conversion stage also requires careful clock and layout treatment to preserve full-scale signal integrity. Typical uses include multichannel digital mixers, studio monitoring equipment, consumer hi-fi systems, USB or network audio interfaces, broadcast consoles, and general-purpose audio data-acquisition modules. The 96 kHz sampling rate is suitable for high-quality audio conversion, while the 20-bit code width provides useful headroom for downstream mixing and filtering. PCB implementation should separate analog and digital return paths, provide local supply bypassing at the device pins, and route the clock and data signals away from sensitive analog inputs. The 24-pin VSOP footprint requires a land pattern matching the manufacturer’s package drawing, including correct pin-one orientation and exposed-pad requirements if applicable. This product page combines the verified AK5352VF conversion specifications, package information, sourcing guidance, and application-oriented design context. It also distinguishes documented characteristics from parameters that require confirmation in the manufacturer datasheet, helping engineers plan a correct audio-converter implementation before layout release.
AK5354VT - 20-Bit Low-Power ADC with PGA | AKM Semiconductor
Asahi Kasei Microdevices/AKM AK5354VT is a low-voltage 20-bit delta-sigma analog-to-digital converter for digital audio systems, distributed in tape-and-reel packaging. The converter operates from a low-voltage supply, uses a 1.8 V digital interface supply, and incorporates an analog input programmable-gain amplifier for single-ended microphone-signal conditioning. An audio ADC is a specialized data-converter IC that converts continuous analog microphone or line-level voltages into sequential digital samples for processing by a codec, DSP, or microprocessor. The AK5354VT belongs to the delta-sigma ADC family within the broader analog-to-digital converter, signal-conversion, and semiconductor hierarchies. Its integrated PGA allows a microphone signal to be amplified before conversion without requiring a separate analog gain stage. The principal feature set includes 20-bit conversion resolution, an integrated analog input PGA, single-ended analog input, and a 1.8 V digital supply connection. The single-ended input architecture can simplify source wiring and reduce the number of external input filters required by the device. These functions make the converter suitable for digital-audio recording, microphone capture, and compact audio input modules. Technically, the AK5354VT uses a low-voltage delta-sigma conversion architecture intended to balance conversion resolution with low power consumption. The digital interface can operate from 1.8 V, supporting systems built around low-voltage processors and digital audio engines. The PGA is placed in the analog signal path ahead of the converter, so microphone sensitivity and signal headroom should be considered together when selecting the gain configuration. Typical applications include digital microphones, microphone preamplifier modules, portable audio recorders, USB audio interfaces, and embedded audio capture systems. In these systems, the converter can accept a single-ended analog microphone source, provide adjustable analog gain, and present digital conversion data to a downstream DSP or audio codec. Design attention should focus on analog input conditioning, decoupling, digital-interface compatibility, and conversion-clock implementation. The input network must limit out-of-band energy, while power and ground arrangements should prevent switching activity from contaminating the low-level microphone signal. This page combines the manufacturer datasheet, verified product listings, application-focused engineering guidance, lifecycle observations, and family comparisons for engineers evaluating the AK5354VT. It also distinguishes documented drop-in replacements from related converters whose package and pin compatibility have not been established.
AK5355VT - 16-Bit Low-Power Audio ADC | Asahi Kasei
The Asahi Kasei Microdevices AK5355VT is a low-power, 16-bit serial delta-sigma analog-to-digital converter with an integrated input gain amplifier, designed for digital-audio and microphone-signal conversion. The device operates from a 2.1 V to 3.6 V supply, supports an industrial temperature range of -40°C to +85°C, and is supplied in a surface-mount 16-pin TSSOP package. Its combination of 16-bit conversion resolution, integrated gain amplification, and low-voltage operation makes it suitable for audio front ends handling low-level input signals. An analog-to-digital converter is an integrated circuit that samples an analog voltage and converts it into a digital representation. The AK5355VT belongs to the ADC hierarchy: delta-sigma ADC, serial ADC, audio ADC, data-converter IC, and integrated circuit. In audio systems, this conversion stage turns microphone or line-level analog signals into serial digital data that can be processed by an audio codec, DSP, digital mixer, or digital recording equipment. Key verified characteristics include 16-bit resolution, delta-sigma conversion, a serial output interface, and an integrated input gain amplifier. The integrated amplifier reduces the need for a separate microphone preamplifier when operating with suitably low-level inputs. The 2.1 V to 3.6 V operating range is appropriate for low-voltage portable, consumer-electronics, and embedded audio equipment, while the -40°C to +85°C range supports industrial-temperature operation. The AK5355VT uses a serial digital interface, allowing digitized audio to be transferred through a compact connection rather than a parallel bus. This can reduce wiring and PCB routing requirements, although the host processor must be configured to clock and frame the serial data correctly. Exact sampling rate, input bandwidth, clock requirements, digital-interface voltage, and conversion-performance figures were not included in the supplied verified data and therefore require confirmation from the manufacturer datasheet. Typical uses include digital microphones, microphone-array preamplification, audio-recording modules, portable audio equipment, and industrial sound-capture systems. The integrated gain amplifier is especially relevant when the source signal is weak, while the low-voltage supply range simplifies integration with modern 3.3 V digital systems. Designers should verify input range, programmable gain, clocking, serial-format compatibility, and decoupling requirements before layout release. Input and reference circuitry should be placed for low noise, with short analog routing and controlled return paths. The AK5355VT is appropriate when a 16-bit, low-power, 16-TSSOP audio ADC is required, but a different converter may be preferable when a specific sampling rate, channel count, digital format, or pin-compatible second source is mandatory. This product page consolidates the verified electrical, environmental, package, pricing-reference, and sourcing information for the AK5355VT and distinguishes confirmed specifications from parameters that still require datasheet confirmation. It also provides selection guidance, application context, and an honest assessment of the limited drop-in replacement data available.
AK5357ET - 24-Bit Stereo Audio ADC, 96 kHz | AKM
The Asahi Kasei Microdevices/AKM AK5357ET is a 24-bit stereo audio analog-to-digital converter with a sampling-rate range of 4 kHz to 96 kHz, supplied in a 16-pin TSSOP package. It uses Enhanced dual-bit delta-sigma conversion techniques to provide high accuracy for multimedia audio systems and accepts I2S-format digital audio output. The device is designed for applications where two audio channels must be digitized with a high-resolution serial interface. An audio ADC is a specialized data-acquisition IC that converts left- and right-channel analog audio voltages into sequential digital samples. Within the signal path, the ADC belongs to the broader ADC/DAC category and ultimately to the integrated-circuit and data-conversion families. Its sampling rate defines how many audio samples are captured each second, while the 24-bit conversion resolution establishes the numerical format of the resulting samples. The AK5357ET operates with the audio clock signals MCLK, SCLK, and LRCK. The manufacturer datasheet states that all external clocks must be present unless the PDN pin is held low. If the external clocks are absent, placing the converter in power-down mode prevents its internally refreshed logic from drawing excess current. This clock-control requirement makes power sequencing an important part of the surrounding system design. A typical implementation places the AK5357ET after the microphone preamplifier or line-level input stage. Analog inputs are sampled, converted by the dual-bit delta-sigma architecture, and transferred to a digital audio processor or audio codec through the serial interface. The 16-pin TSSOP package is suitable for compact consumer audio, communication, and multimedia equipment where board area is constrained. When designing the PCB, treat MCLK, SCLK, and LRCK as sensitive digital timing signals and route them away from analog input traces. Establish analog and digital ground partitioning according to the layout guidance in the manufacturer datasheet, and place input and interface components close to their associated pins. The analog signal path should be kept short and away from high-current switching nodes. This page consolidates the confirmed converter characteristics, interface requirements, application guidance, and a verified same-family replacement into a design-focused component reference for audio subsystem engineers.
AK5357VT - 24-Bit Stereo Audio ADC | Asahi Kasei
Asahi Kasei Microdevices AK5357VT is a 24-bit stereo audio analog-to-digital converter with a sampling-rate range of 4 kHz to 96 kHz, an I2S interface, and a 16-pin TSSOP package. The converter uses enhanced dual-bit delta-sigma techniques to support multimedia audio acquisition. An audio ADC is an interface integrated circuit that converts left and right analog audio signals into digital samples. It belongs to the data-converter hierarchy, which includes ADCs and DACs, and operates as part of a broader audio signal-chain semiconductor. Audio ADCs are commonly positioned between microphones, line inputs, and digital audio processors. The AK5357VT supports sampling rates from 4 kHz through 96 kHz, making it suitable for voice capture, multimedia equipment, and stereo digital-audio systems. Its 24-bit resolution provides 16,777,216 discrete codes per sample. Digital audio data is transferred through an I2S interface, while the converter operates from a 2.7 V to 5.5 V supply range. Enhanced dual-bit delta-sigma conversion is the core signal-processing technique used by the AK5357. Delta-sigma architecture shapes quantization noise into a higher-frequency band, where digital filtering can reduce its effect on the audio passband. This approach is particularly useful when high resolution and compact implementation are more important than the very low noise associated with a conventional linear converter. Typical uses include stereo multimedia audio inputs, digital-recording equipment, consumer audio interfaces, and systems that accept analog line-level signals for conversion to I2S data. The broad sampling-rate range also allows one converter design to cover multiple audio standards, from low-rate speech processing through high-rate multimedia playback and capture. System integration requires correct clocking because MCLK, SCLK, and LRCK must be present during active operation. If those external clocks are absent, the PDN pin should be driven low to place the AK5357VT in power-down mode. This prevents excess current caused by internal dynamically refreshed logic operating without required clock signals. This product page consolidates the core electrical characteristics, clocking requirements, package information, drop-in candidates, and practical integration notes for engineers evaluating the AK5357VT. Use the AK5357 English datasheet for the authoritative pin-description table, application circuit, electrical characteristics, and ordering information.
AK5358AET - 24-Bit Stereo ADC, 8-96kHz | AKM
The Asahi Kasei Microdevices AK5358AET is a stereo 24-bit audio analog-to-digital converter with a sampling-rate range of 8 kHz to 96 kHz, housed in a 16-pin TSSOP package. It is designed for consumer and professional audio systems that require conversion of left and right analog audio channels into a digital I2S stream. An audio ADC is a mixed-signal semiconductor that converts continuous analog voltage signals into digital data for processing, storage, transmission, or playback. Its position in the signal chain is between the analog input section and the digital audio subsystem. Within the broader semiconductor hierarchy, the AK5358AET belongs to the ADC and DAC class of data-converter ICs, combining analog input circuitry, clocking, filtering, and a digital audio interface in one package. The principal specifications distinguish the AK5358AET from lower-resolution or lower-rate converters. Its 24-bit resolution supports high numerical precision, while the 8 kHz minimum and 96 kHz maximum sampling rates cover voice-band through high-resolution audio acquisition. The integrated I2S interface provides a conventional digital connection for audio processors, and the stereo architecture reduces the number of separate converter packages required for a conventional two-channel signal path. The converter uses Enhanced dual-bit delta-sigma technology. This architecture supports accurate conversion while integrating the analog and digital conversion functions into a compact mixed-signal IC. A delta-sigma ADC includes a modulator and digital decimation-filter functions rather than relying only on a conventional flash or successive-approximation conversion structure. The AK5358A device also includes power-down control and digital-filter reset behavior, with output availability occurring after the documented initialization sequence following operation. Typical uses include consumer audio equipment, professional recording and playback systems, microphone preamp and line-input conversion, USB or network audio interfaces, and industrial monitoring systems that must capture stereo audio. The I2S interface is particularly useful when the converter is connected to a digital signal processor, audio codec, microcontroller, or dedicated USB audio controller. A practical design must preserve clean analog grounding, short input routing, suitable input biasing, and stable clock and power connections. Follow the manufacturer datasheet for analog input, common-mode voltage, digital-interface mode, power-supply sequencing, and decoupling values. The datasheet also requires proper power-down and initialization handling so that valid output data is not interpreted before the converter has completed its startup sequence. This product record combines the AK5358AET converter specifications, package and interface details, sourcing information, application guidance, and drop-in replacement analysis. It also distinguishes confirmed same-package candidates from products that merely perform a similar function, helping engineers avoid substitutions that require PCB or interface changes.
AK5358BET - 24-Bit Stereo ADC, 8-96kHz | AKM
Asahi Kasei Microdevices/AKM AK5358BET is a 24-bit stereo delta-sigma analog-to-digital converter with a sampling rate range of 8 kHz to 96 kHz, a 5 V analog and digital supply, and a 16-pin TSSOP package with 0.65 mm pitch. It is designed for consumer and professional audio systems that require simultaneous conversion of left and right analog audio channels into 24-bit digital data. An audio ADC is a mixed-signal data converter that samples an analog input, quantizes each sample to a digital value, and applies digital filtering before transferring the result through a digital audio interface. The AK5358BET belongs to the ADC/DAC and audio data-converter hierarchy, where its role is to bridge analog microphones, line-level sources, and playback equipment with digital audio processors, codecs, recording systems, and digital consoles. The principal features of the AK5358BET include 24-bit resolution, dual-channel operation, an 8 kHz to 96 kHz sampling-rate range, 5 V operation, and an I2S-compatible digital interface. These parameters suit applications where the source bandwidth is below the converter's usable audio range and where the system requires more precision than a conventional low-resolution multimedia converter. The dual-channel architecture allows left and right signals to be captured in one compact package. The converter uses enhanced dual-bit delta-sigma conversion techniques to balance resolution, digital filtering, and implementation cost. Its digital interface permits the converted stereo audio stream to be connected to an audio codec, digital mixer, signal processor, or microcontroller. Designers should pay attention to the required master clock, bit clock, and frame-clock relationships because correct interface timing is essential for recovering synchronized 24-bit samples. Typical applications include professional audio recording equipment, consumer audio systems, digital mixing consoles, microphone preamplifier and analog-to-digital conversion stages, multimedia equipment, and industrial audio acquisition systems. The AK5358BET is especially relevant when a system needs a dedicated stereo 24-bit ADC rather than the conversion functions of a broader audio codec. A critical implementation consideration is preserving the analog signal path before conversion. Keep input traces short, maintain the layout recommended by the manufacturer datasheet, provide stable analog and digital supplies, and place decoupling capacitors close to their associated pins. Confirm interface voltage levels and clock relationships against the device data sheet before finalizing the PCB. This product page organizes the AK5358BET specifications, verified source links, replacement options, application guidance, and design considerations into an engineering-focused resource. It also distinguishes confirmed drop-in candidates from family variants so that replacement decisions can be made against package, resolution, sampling-rate, and interface requirements rather than part-name similarity alone.
AK5359ET - 24-Bit 192kHz Stereo Audio ADC | AKM
Asahi Kasei Microdevices AK5359ET is a 24-bit stereo audio analog-to-digital converter with a maximum sampling rate of 192 kHz, packaged in a 16-TSSOP. It uses Enhanced dual-bit delta-sigma conversion and provides an I2S serial output interface. The device is intended for consumer and professional audio systems that require high-resolution digital audio capture. An audio ADC is a mixed-signal integrated circuit that converts left and right analog audio voltages into a digital bit stream. The AK5359ET belongs to the delta-sigma ADC family, a category of converters commonly used for digital recording, microphones, mixing consoles, and consumer playback equipment. Its stereo architecture captures two analog audio channels while reducing the number of external conversion paths required on a system board. The AK5359ET provides 24-bit resolution and a 192 kHz maximum sampling rate. Its stated sampling-rate range extends from 8 kHz to 216 kHz, allowing the same converter architecture to support voice, compact-disc-rate audio, high-resolution studio audio, and other digital recording formats. An I2S output supports connection to audio processors, digital audio codecs, DSP devices, and transport interfaces. Internally, the converter uses Enhanced dual-bit delta-sigma techniques to achieve accurate conversion while controlling cost and power consumption. The 16-TSSOP package is approximately 4.40 mm wide and uses a 0.65 mm lead pitch. Because it is a surface-mount component, the package is supplied on tape and reel for automated assembly. The analog supply range is listed as 4.5 V to 5.5 V, while the digital supply range is listed as 3 V to 5.5 V. Typical applications include professional audio recorders, USB audio interfaces, studio monitors, digital mixers, broadcast equipment, and consumer audio systems. Its 24-bit resolution is useful for retaining fine amplitude detail during conversion, while the 192 kHz rate supports high-resolution recording and professional playback workflows. In multi-channel systems, multiple converters can be synchronized according to the device's documented operating conditions. Layout is critical in an audio ADC because analog input, digital clock, and I2S output paths must remain appropriately separated. Place input and supply bypass capacitors close to their associated pins, keep digital return currents away from sensitive analog inputs, and use a continuous ground reference beneath the device where the recommended layout permits. Confirm the complete pin assignments and decoupling values in the manufacturer datasheet before layout release. This product page organizes the AK5359ET conversion format, sampling capability, supply requirements, package information, design considerations, and documented alternatives. It also highlights the distinction between true pin-compatible replacements and broader functional similarities so engineers can assess board-reuse risk before approving a substitution.
AK5359VT - 24-Bit 192kHz Stereo ADC | Asahi Kasei Microdevices
The Asahi Kasei Microdevices (AKM) AK5359VT is a 24-bit stereo delta-sigma analog-to-digital converter (ADC) supporting a wide sampling rate range of 8 kHz to 216 kHz, packaged in a TSSOP-16 surface-mount form factor. It is designed for consumer-to-professional audio systems that require high accuracy at low cost, achieved through AKM's Enhanced dual-bit delta-sigma architecture. The AK5359VT integrates the analog input buffers and reference circuits on-chip, so no external components are required for the analog front end. A delta-sigma ADC is a type of analog-to-digital converter that uses oversampling and noise shaping to achieve high resolution (24-bit in this case) at moderate bandwidth. Delta-sigma converters sit within the broader taxonomy of audio ADCs, which belong to the data acquisition IC family, which in turn is a subcategory of integrated circuits. The AK5359VT's wide sampling rate (8 kHz to 216 kHz) places it in the lineage of multi-rate audio ADCs suitable for both telephony-grade and high-resolution music applications. Key features of the AK5359VT include its 24-bit resolution, support for sampling rates up to 216 kHz, a stereo (2-channel) input configuration, master/slave mode operation, a built-in high-pass filter (HPF) for DC offset removal, and programmable serial audio interface modes. Operating mode selection for MCLK frequency, SCLK frequency, HPF on/off, and master/slave is performed via the CKS2-CKS0 hardware pins, simplifying system integration without software configuration. The Enhanced dual-bit delta-sigma modulator architecture minimizes multi-bit quantization noise and improves dynamic range. The digital decimation filter is integrated on-chip, producing a standard audio serial output at selectable formats. Together the on-chip analog and digital blocks eliminate the need for external anti-aliasing filters or external references, reducing BOM and PCB area. Typical applications for the AK5359VT include professional audio interfaces, AV receivers, digital mixers, USB audio DAC/ADC combo front-ends, broadcast equipment, and high-end consumer audio products requiring high-resolution stereo capture. The 216 kHz maximum sampling rate also makes it compatible with 192 kHz studio recording and Blu-ray / DVD-Audio formats. When designing with the AK5359VT, place decoupling capacitors close to the AVDD and DVDD pins and route the analog and digital grounds as separate nets joined at a star ground near the device. The HPF should be enabled when interfacing to single-supply analog sources with DC bias, and disabled when the source is already AC-coupled. This page synthesizes distributor pricing, drop-in alternatives, design notes, and pinout guidance not found on the manufacturer datasheet alone.
AK5365VQ - 24-Bit 96kHz Audio ADC | AKM | LQFP-44
Asahi Kasei Microdevices AK5365VQ is a high-performance 24-bit audio analog-to-digital converter with an integrated audio selector, programmable gain amplifier, and automatic level control for consumer audio and digital recording equipment. It supports sampling rates from 32kHz to 96kHz, communicates through I2C and SPI interfaces, and is packaged in a 44-LQFP measuring 10mm by 10mm. The converter also uses AKM Enhanced Dual-Bit modulator architecture to support high-resolution audio conversion. An audio ADC is a mixed-signal semiconductor that converts continuous analog microphone or line-level signals into digital PCM data. Its broader hierarchy is ADC -> data converter -> audio converter -> mixed-signal integrated circuit. The AK5365VQ combines this conversion function with input selection, gain control, and automatic level control, reducing the number of separate analog components required in consumer audio and recording systems. Key features include 24-bit resolution, a maximum sampling rate of 96kHz, two-channel operation, and support for both I2C and SPI host interfaces. The integrated selector routes audio sources, while the PGA provides adjustable analog gain and the ALC function helps maintain an appropriate signal level. These functions make the device particularly suitable for compact digital-recording products requiring high-resolution conversion without a large external analog signal chain. The AK5365VQ operates from dual supply rails, with digital and analog supply ranges identified as 3V to 5.25V and 4.75V to 5.25V, respectively. I2C and SPI connectivity allows the converter to pair with application processors, digital audio processors, and digital-recording controllers. The 44-LQFP package provides a defined 10mm by 10mm footprint and 44 numbered terminals for compact, high-density equipment designs. Typical applications include consumer audio equipment, digital recorders, microphone preamp and capture systems, audio interfaces, and portable recording products. Its 24-bit resolution is appropriate for lossless or high-resolution PCM workflows, while the 96kHz maximum rate supports audio beyond the 48kHz CD sampling rate. Systems requiring higher channel counts, different electrical interfaces, or a smaller package should evaluate the complete signal chain before integrating the device. The primary design consideration is separating analog and digital supplies while maintaining short, low-noise routing between the microphone inputs, reference circuitry, and ground planes. Decoupling capacitors should be placed directly at the relevant supply terminals, and the analog input network should avoid digital return currents. Confirm startup sequencing, interface mode settings, supported clock configurations, and the complete pin description against the manufacturer datasheet before releasing production hardware. This product page combines the exact AK5365VQ device identity, package and interface information with application-oriented design guidance, sourcing questions, and a structured comparison framework. Because no pin-compatible substitute was established, the page does not present electrically similar devices as drop-in replacements; PCB changes or different converter architectures should be treated as redesigns rather than substitutions.
AK5366VQ - 24-Bit 48kHz ADC with PGA/ALC | AKM Audio
The Asahi Kasei Microdevices AK5366VQ is a 24-bit, 48 kHz sampling ADC with an integrated input selector, programmable gain amplifier, and automatic level control for consumer audio and digital-recording equipment. The device is associated with the AKM AK5366 series and is supplied in a tray package. Its combination of audio conversion resolution, input selection, PGA, and ALC functions places analog input conditioning and conversion in one dedicated audio-converter IC. An ADC is a data-acquisition and signal-conversion integrated circuit that converts an analog voltage into a digital representation. In audio equipment, the converter's bit depth helps describe the numerical resolution of each sample, while its sampling rate determines how many samples are processed each second. The AK5366VQ operates as a 24-bit ADC at 48 kHz and is specifically oriented toward consumer audio and digital recording rather than general-purpose high-speed instrumentation. The selector allows multiple analog input paths to be routed to the conversion system, reducing the need for external source-selection circuitry in multi-source audio products. The PGA provides controllable analog gain before digitization, allowing the front end to better match source levels to the converter range. The ALC function helps maintain a more consistent signal level when input amplitudes vary. Together, these functions simplify the audio signal path while reducing the number of discrete conditioning blocks required around the ADC. The AK5366 series documentation also identifies the AKD5366VR-A as an evaluation board for the 24-bit, 48 kHz digital-audio ADC, with an input circuit and a digital-interface transmitter. This reference implementation is useful for evaluating the conversion architecture and input-conditioning behavior before integrating AK5366VQ into a finished audio product. Exact electrical limits, interface timing, clocking requirements, and pin assignments should be confirmed in the manufacturer datasheet before schematic capture. Typical applications include consumer-audio analog input sections, digital recorders, microphone preamplifier interfaces, home-audio equipment, and other products that combine selectable analog sources with gain and level-control functions. The AK5366VQ is particularly relevant when a design needs one audio ADC rather than separate selector, gain-control, and conversion stages. For implementation, begin with the manufacturer pin description and typical application circuit, then allocate the analog, digital, clock, and power sections according to those recommendations. Preserve the recommended input and output component values around the converter, and verify clock timing and digital-interface settings against the device documentation before production testing. This product page consolidates the exact AK5366VQ series description, packaging information, sourcing references, application guidance, and replacement-screening criteria into a design-focused resource. For current commercial availability, use the Request a Quote form on this page and confirm production quantities, lifecycle status, and delivery timing before placing an order.
AK5367AEF - 24-Bit Stereo ADC, 96 kHz | AKM
The Asahi Kasei Microdevices AK5367AEF is a high-performance 24-bit stereo analog-to-digital converter for consumer audio and digital recording systems, with a sampling rate of 32 kHz to 96 kHz, analog and digital supply voltages of 3 V to 3.6 V, an I2C interface, and a 30-pin VSOP package. An ADC is an analog-to-digital converter, a data-conversion IC that samples continuous analog audio voltages and converts them into proportional digital values. The AK5367A belongs to the ADC and DAC hierarchy within data-conversion ICs, where it serves as the bridge between analog microphone or line-level audio and a digital audio processor. Its stereo architecture processes two audio channels while its I2C control interface allows a host controller to configure operating conditions and read device status. The primary specifications are 24-bit resolution, a 32 kHz to 96 kHz sampling-rate range, and a 3 V to 3.6 V analog and digital operating range. The converter is intended for consumer audio and digital-recording applications where a compact surface-mount implementation, stereo capture, and high-resolution conversion are important. Its documented operating-temperature ordering option covers -20 °C to +85 °C. The AK5367A provides separate analog and digital supply pins, supporting careful partitioning of analog signal paths and digital interfaces on a mixed-signal PCB. An I2C control path and I/O-oriented clock pins provide integration with audio codecs, digital signal processors, and embedded audio systems. The device also supports power-down control, allowing its digital filter to be reset when the power-down pin is asserted low. Typical uses include digital microphones, USB or portable audio equipment, consumer recording systems, audio capture accessories, and stereo line-input converters. The 24-bit format supports high-resolution audio workflows, while the 96 kHz maximum sampling rate supports 48 kHz and 96 kHz digital-audio streams. The compact 30-pin VSOP with 0.65 mm pitch is suited to space-constrained boards requiring fine-pitch assembly. Layout is critical because analog and digital supplies must be decoupled close to their corresponding pins, and high-speed signals require short controlled routes. Confirm the pin-description table in the manufacturer datasheet before assigning tracks or selecting the system clock. The PDN control net should be sequenced so that the required reset action follows power-up. This product page organizes the documented AK5367AEF characteristics, package information, interface considerations, and practical application guidance. It also distinguishes verified drop-in replacements from merely similar converters, helping PCB designers avoid substitutions that differ in footprint, pin assignment, or audio interface behavior.
AK5367EF - 24-Bit 96kHz 4-Channel Audio ADC | AKM
Asahi Kasei Microdevices AK5367EF is a four-channel, 24-bit delta-sigma audio ADC optimized for consumer audio and digital recording systems. It supports sampling rates up to 96kHz and incorporates a four-channel selector with 0V bias operation. The device is supplied in a 30-VSOP surface-mount package, providing a compact interface for multi-channel audio capture and playback architectures. An audio ADC is a mixed-signal data-acquisition IC that converts analog audio signals into high-resolution digital words for processing by DSPs, microcontrollers, audio codecs, or digital recording equipment. In the broader semiconductor hierarchy, the AK5367EF belongs to the ADC/DAC class of data-conversion ICs, combining a low-noise analog input stage, delta-sigma modulator, digital filter, and serial digital interface in one integrated circuit. The principal features of the AK5367EF include 24-bit resolution, a maximum sampling frequency of 96kHz, four selectable analog input channels, and a 0V-bias selector. These characteristics suit systems that need to capture multiple analog sources while maintaining a consistent digital audio format. The selector function allows a system to route or select among multiple audio inputs, reducing the need for separate analog switching devices when the selected channels share compatible signal characteristics. Internally, the AK5367EF uses a delta-sigma conversion architecture suitable for high-resolution audio digitization. Its multi-channel selector and digital output interface position it between analog microphone or line-level front ends and a downstream digital audio processor. The 30-VSOP package requires careful PCB layout around high-speed digital signals and analog input routing to maintain signal integrity and minimize channel-to-channel interference. Typical uses include consumer audio equipment, digital recorders, multimedia appliances, instrument or mixer input modules, and multi-source digital audio capture systems. When designing around this converter, pay particular attention to analog supply decoupling, reference stability, input common-mode range, supported interface mode, and the required relationship between master clock, serial clock, and data timing. This page combines the verified product characteristics with practical integration guidance, an explicit drop-in-replacement assessment, and an application-oriented comparison framework. Engineers should use the manufacturer datasheet for the authoritative pin-description table, timing diagrams, recommended external circuitry, and electrical-limit values before finalizing a PCB or production design.
AK5371AVQ USB Audio ADC, 16-bit, 48-LFQFP | AKM
The Asahi Kasei Microdevices AK5371AVQ is a two-channel 16-bit audio analog-to-digital converter with an integrated USB interface, USB transceiver, audio controller, endpoints, and digital audio processing. It supports sampling rates from 8 kHz to 48 kHz, operates from a 3 V to 3.6 V supply, and is housed in a 48-LFQFP 7 x 7 mm package. A USB audio ADC is a mixed-signal interface IC that converts left and right analog audio inputs into digital PCM data for transmission over USB. The AK5371AVQ integrates the complete acquisition path needed by a USB audio peripheral: stereo analog-to-digital conversion, clocking, USB serial-interface handling, transceiver functions, endpoint management, and audio-class processing. This integration reduces the number of external interface components required in a USB microphone, headset, or compact audio capture design. The converter provides 16-bit resolution across the 8 kHz to 48 kHz range. According to the AK5371A datasheet description, the signal-to-noise ratio reaches 84 dBA at a 44.1 kHz sampling rate with 0 dB gain. The device also includes mute and volume-control functions, two endpoints with FIFO buffering, and a low-power design intended for USB-powered or low-power embedded audio equipment. USB-IF certification is identified for the AK5371A family, which is important when interoperability and USB audio-class behavior are central to product qualification. Integrating the USB transceiver and audio controller allows the converter to operate as a dedicated USB audio capture device rather than requiring a separate USB controller in the signal path. The resulting system can present a conventional stereo USB audio interface to a host computer, embedded system, or connected test equipment. Typical uses include USB microphones, headset adapters, conference-audio peripherals, digital recording interfaces, and embedded audio acquisition modules. The 48-LFQFP package is suitable for compact boards, although its fine pitch and exposed thermal-pad arrangement require careful PCB layout. The 3 V to 3.6 V operating range also means that the device is normally paired with a regulated 3.3 V rail. For a new design, check the manufacturer’s pin-description table, recommended analog input network, USB routing guidance, and clock requirements before assigning PCB tracks. Decoupling capacitors should be placed directly beside the appropriate supply and ground pins, while the USB data and differential-pair routing should preserve controlled impedance and minimize interference with the analog input section. This page organizes the AK5371AVQ’s principal conversion, USB, supply, package, and application characteristics with practical replacement guidance and engineering-oriented design notes. It is intended to help designers evaluate integration requirements, board constraints, sample-rate support, and sourcing alternatives before committing a 48-LFQFP layout.
AK5373EQ - 24-Bit Stereo USB 2.0 ADC | AKM Semiconductor
AKM Semiconductor AK5373EQ is a 24-bit stereo analog-to-digital converter with a 48 kHz sampling rate, integrated USB 2.0 interface, USB transceiver, and audio-class processing in a 48-pin LQFP package measuring 7 x 7 mm with a 0.50 mm pitch. The device operates from a 3 V to 3.6 V supply and is specified for commercial temperatures from -10°C to 70°C. An audio ADC is an interface IC that converts left- and right-channel analog audio into digital samples for processing, storage, transmission, or playback. The AK5373EQ combines two audio conversion channels with a digital USB interface, placing the analog front end, conversion function, clocking, and USB connectivity within one device. Its 24-bit resolution preserves a large dynamic range for consumer audio, USB microphones, and compact digital recording equipment. The AK5373EQ supports 48 kHz sampling, a common rate for CD-quality stereo audio and USB playback. Its integrated USB 2.0 interface and USB transceiver reduce the need for a separate USB controller in a simple audio peripheral. The 3 V to 3.6 V analog and digital supply range suits low-voltage portable systems in which USB-powered equipment must operate from limited rail headroom. The 48-pin LQFP provides all 48 package positions required by the device footprint. The AKM product description identifies the AK5373EQ as a stereo A/D converter with an integrated USB serial interface engine, USB transceiver, and audio-class processing. This integration supports a compact USB audio architecture while reducing board-level interface complexity. Commercial screening and the -10°C to 70°C operating range target room-temperature consumer and communication equipment rather than extended industrial or automotive environments. Typical uses include USB stereo microphones, digital audio recorders, USB audio adapters, computer peripherals, and compact multimedia input devices. In these systems, the converter can accept two analog audio channels, sample them at 48 kHz, and present the digital stream through USB. The integrated interface is especially useful where enclosure space, external component count, and direct host connectivity are priorities. Design the analog input network for the intended source impedance and signal level, and keep high-speed USB routing away from sensitive audio traces. Place the required decoupling capacitors close to their associated supply pins, observe the manufacturer's recommended clock and interface configuration, and confirm enumeration behavior with the target USB host. PCB rework is necessary because the AK5373EQ uses a 48-pin LQFP rather than a leadless package. This product record combines the verified electrical specifications, package details, lifecycle information, application guidance, and design considerations for engineers evaluating the obsolete AK5373EQ. It also distinguishes the device from less suitable replacements by emphasizing its exact 24-bit, 48 kHz, USB 2.0 stereo-ADC configuration and the need to confirm pin, clock, and USB compatibility before substitution.
AK5374EN - 24-Bit 48kHz USB Audio ADC | Asahi Kasei
Asahi Kasei Microdevices AK5374EN is a stereo 24-bit audio analog-to-digital converter with USB 2.0 connectivity and a 48 kHz sampling rate, packaged in a 36-pin QFN measuring 5 mm by 5 mm. The device integrates a USB serial interface engine, USB transceiver, Audio Class processing block, endpoints, and a two-channel ADC, reducing the external circuitry needed for USB digital audio capture. An audio ADC is a mixed-signal integrated circuit that converts left- and right-channel analog audio into digital sample data. In the signal-chain hierarchy, the AK5374EN sits between microphones, line inputs, or other analog audio sources and a USB audio host. Its integrated USB interface combines conversion, clocking, endpoint management, and digital transport in one package, making it suitable for compact USB audio equipment. The principal features include stereo 24-bit conversion, operation up to 48 kHz, an integrated USB 2.0 interface, and a 3 V to 3.6 V supply range. Commercial-grade screening and an operating range of -10°C to +70°C suit room-temperature consumer, computing, and communications equipment. The 5 mm by 5 mm QFN-36 package uses a 0.40 mm pin pitch and is described as halogen-free and plastic-bodied. Technically, the AK5374EN combines analog input conversion with a full-speed USB serial interface engine. The Audio Class processing block and endpoints support digital audio transfer between the converter and a connected USB host, while the integrated transceiver reduces the need for discrete USB interface components. The analog section accepts a nominal 0 V to 1.4 V input range, allowing compatibility with common line-level signals when the surrounding circuit provides appropriate attenuation, biasing, and signal conditioning. Typical uses include USB microphones, headset interfaces, portable digital recorders, conference-audio terminals, streaming devices, and industrial audio-capture adapters. In each case, the stereo inputs can be conditioned before conversion, and the integrated USB interface can connect directly to a host computer or embedded USB controller. The compact QFN-36 package supports space-constrained products but requires careful PCB layout and thermal verification. The primary design consideration is analog signal integrity. Keep analog input routing short, maintain a continuous ground reference, decouple the supply close to the device, and follow the manufacturer datasheet for USB impedance and clock recommendations. Because the converter and transceiver share a compact package, converter, clock, and USB return-current paths should be arranged to minimize coupling into the audio input stage. This product overview combines the verified AK5374EN electrical and package characteristics with practical guidance for USB audio capture designs. It also identifies the major selection criteria—resolution, sample rate, USB integration, package size, operating grade, and analog-input requirements—without substituting an unverified substitute for a confirmed pin-compatible device.
AK5380VT - 24-Bit 96kHz Stereo Audio ADC | AKM
The Asahi Kasei Microdevices AK5380VT is a 24-bit stereo audio analog-to-digital converter with a 4kHz to 96kHz sampling-rate range and a 16-pin TSSOP package. It uses enhanced dual-bit delta-sigma conversion to provide high-resolution digital audio output through an I2S interface. The AK5380VT is intended for high-end audio systems requiring two-channel conversion and digital sample rates extending to 96kHz. An audio ADC is a specialized data-converter IC that converts continuous analog voltage signals into digital words suitable for processing, storage, or transmission. In the signal-chain hierarchy, the AK5380VT belongs to the ADC and DAC category, operates as a stereo audio converter, and ultimately serves as a semiconductor interface device between analog audio circuitry and a digital audio subsystem. The device supports a 24-bit resolution and a maximum sampling rate of 96kHz, while its enhanced dual-bit delta-sigma architecture is intended to improve conversion accuracy and implementation economy. It accepts single-ended analog input according to the AK5380VT product description. Digital audio data is delivered through an I2S-compatible interface, allowing connection to digital audio processors, receivers, recorders, and other systems capable of receiving the required clock and data signals. The AK5380VT operates from a 2.7V to 5.5V supply range and is specified for temperatures from -40°C to 85°C. Its 16-pin TSSOP package supports surface-mount assembly. The analog input stage is the primary thermal and layout-sensitive area, while the digital interface requires careful clock and signal routing to prevent data corruption. Power, ground, and analog-input connections should be arranged according to the manufacturer datasheet. Typical uses include high-end digital audio equipment, multichannel sound systems, audio recording equipment, and consumer-electronics products requiring stereo conversion at rates up to 96kHz. Its single-ended input architecture can simplify source interfacing when the analog front end can be referenced cleanly to the converter's ground network. For a new design, begin with the manufacturer pin description and application circuit, then verify input range, output logic levels, clocking, and digital interface mode before layout. Place analog and digital return currents separately, decouple each supply domain near the device, and route the I2S signals away from high-current switching nodes. This product page consolidates the AK5380VT's core electrical characteristics, interface details, verified source links, and application-oriented design guidance. It also distinguishes documented function and supply information from replacement decisions, where pin compatibility and interface timing must be confirmed before a substitution is approved.
AK5381ET - 24-Bit Stereo 96 kHz ADC | Asahi Kasei
Asahi Kasei Microdevices/AKM AK5381ET is a 24-bit stereo delta-sigma audio analog-to-digital converter with a sampling-rate range of 4 kHz to 96 kHz, supplied in a 16-pin TSSOP package with 0.65 mm lead pitch. It accepts left- and right-channel analog audio through dedicated AINL and AINR inputs and provides digital audio data through its serial interface. An audio ADC is a data-acquisition IC that converts left and right analog audio signals into digital words for transmission to a DSP, digital mixer, audio codec, or digital recording system. The AK5381 belongs to the stereo ADC, delta-sigma ADC, audio data-converter, and integrated-circuit hierarchies. Enhanced dual-bit delta-sigma modulation supports its high-resolution conversion function while the digital decimation filter and serial interface provide the resulting audio data to the following processing stage. The principal device characteristics include 24-bit resolution, a maximum sampling rate of 96 kHz, and a 4 kHz minimum sampling rate. The converter supports a 2.7 V to 5.5 V operating supply range and uses I2S serial audio. Its differential analog and digital ground pins help engineers separate analog signal return paths from digital return paths, while AGND, DGND, and VCOM support the converter’s internal analog reference arrangement. The AK5381ET is intended for high-end audio systems in which two channels must be digitized at rates suitable for CD-quality and higher-resolution playback. Its architecture is based on enhanced dual-bit delta-sigma techniques, which provide a straightforward interface between an analog audio front end and a digital audio processing chain. System clocks are handled through MCLK, CKS0, CKS1, and CKS2-related functions, while LRCK, SCLK, and SDTO support serial audio transfer. Typical applications include professional audio equipment, multichannel mixers, digital recording consoles, high-resolution audio interfaces, and consumer playback systems. The 4 kHz-to-96 kHz range makes the converter suitable for voice, conventional CD-rate audio, and higher-rate digital-audio paths. Its two-channel architecture supports balanced stereo conversion when the circuit is arranged according to the manufacturer’s application guidance. The principal design consideration is maintaining clean, quiet analog and digital power rails while preserving the converter’s clock and data timing integrity. Place decoupling capacitors close to the supply pins, route analog and digital returns according to the pin-description and layout guidance in the manufacturer datasheet, and keep high-current digital clock traces isolated from the analog input network. This product page consolidates the AK5381ET conversion capabilities, interface details, pin constraints, application guidance, and documented drop-in considerations into an engineering-oriented reference. It also distinguishes verified device attributes from parameters that require confirmation before layout, sourcing, or production release.
AK5383VS - 24-Bit 96kHz Stereo Audio ADC | AKM
Asahi Kasei Microdevices AK5383VS is a 24-bit, 96 kHz, two-channel delta-sigma analog-to-digital converter for professional digital audio systems. It uses 128-times oversampling and Enhanced Dual Bit modulator architecture, delivers 110 dB dynamic range, and is packaged in a 28-pin plastic SOP format. The AK5383VS also operates from a +5 V analog supply. An audio ADC is a specialized data-converter IC that transforms balanced or unbalanced analog audio into digital PCM data. The digital-audio ADC category sits within signal-chain and data-converter ICs, where precision, low distortion, clocking, and output-interface compatibility determine whether the converter is suitable for recording equipment, digital mixing consoles, studio monitors, broadcast infrastructure, or professional audio interfaces. Key features include 24-bit conversion resolution, two simultaneous analog channels, 128-times oversampling, and a maximum sampling rate of 96 kHz. According to the AKM datasheet, the Enhanced Dual Bit architecture provides 110 dB dynamic range while retaining the low-distortion characteristics associated with single-bit delta-sigma modulators. These characteristics make the AK5383VS appropriate for professional conversion stages requiring high-resolution audio capture. The converter integrates a two-channel audio ADC and a configurable digital audio output stage. Its serial interface supports integration with digital audio processors, clock controllers, sample-rate converters, and professional digital consoles. Designers should treat the analog input, reference, power, ground, and digital clock connections as separate implementation domains because correct partitioning directly affects noise, channel matching, and signal integrity. Typical applications include professional audio interfaces, digital mixing consoles, studio recording equipment, broadcast monitoring, digital loudspeaker processors, and multichannel measurement systems. The two-channel architecture is particularly useful where stereo or balanced dual-channel conversion is required without implementing two separate single-channel converter packages. The primary design consideration is preserving the quality of the analog front end. Balanced inputs, low-noise protection resistors, suitable anti-alias filtering, solid grounding, and clean clock distribution can be as important as the nominal ADC resolution. The +5 V supply and analog inputs also require attention to the datasheet limits because excessive input voltage or current can damage the converter. This product overview combines the manufacturer’s converter architecture, channel and sampling-rate details, package information, application guidance, and drop-in comparison considerations into one engineering reference. It is intended to help hardware designers evaluate signal-chain fit, interface compatibility, and board-level implementation before committing to a professional audio design.