بەرهەمەکان (32)

SY58052AUMG - 10.7Gbps CML Clock Synchronizer | Microchip
SY58052AUMG

SY58052AUMG - 10.7Gbps CML Clock Synchronizer | Microchip

The Microchip Technology SY58052AUMG is an ultra-precision CML data and clock synchronizer (retimer) with a guaranteed maximum data throughput of 10.7Gbps and a maximum clock frequency of 10.7GHz, housed in a 16-pin VFQFN (3x3 mm) exposed-pad package. A data-to-clock resynchronizer is a timing device that reconstructs a clean clock or data edge from a jittery serial data stream by aligning it to a clean reference clock. Within the signal-chain hierarchy, it sits between a clock-and-timing IC and the physical-layer transceivers it serves, forming part of the broader family of PLLs, clock synthesizers, and jitter cleaners used in high-speed serial links. Retiming restores eye diagrams degraded by backplane loss and crosstalk, preventing jitter accumulation across a system. Key features include guaranteed AC performance over temperature and voltage with DC-to-greater-than-10.7Gbps data-rate throughput and DC-to-greater-than-10.7GHz clock fMAX, a 160ps maximum any-input-to-any-output propagation window, and resynchronization of data to a reference clock. The Precision Edge(R) family device accepts CML, PECL, and data-type inputs and delivers CML outputs, easing interface design in mixed signaling environments. The SY58052AU architecture performs edge realignment internally with input and output termination integrated on-chip, reducing external component count and improving signal integrity at multi-gigabit rates. Because the resynchronizer acts as a jitter filter, downstream receivers see a wider eye opening, directly improving bit-error-rate margins in long serial links. Typical applications include backplane retiming, retiming after data transmission over lossy media, 10G Ethernet and SONET/SDH-style serial links, and test-and-measurement instrumentation front ends. The -40C to +85C operating range and 2.375V to 3.63V supply suit telecom and datacom infrastructure equipment. For design, verify the reference-clock jitter budget: the output jitter of the SY58052AU is bounded by the reference clock quality, so use a low-noise crystal oscillator at the CLK input. Keep CML output trace impedances at 50 ohms single-ended to ground-referenced termination. This page synthesizes distributor pricing, cross-reference data, and application guidance not consolidated in the manufacturer datasheet. Pricing as of 2026-10-10.

RFQ پەیوەندی
SY58052AUMG-TR - 10.7Gbps CML Data-Clock Synchronizer | Microchip
SY58052AUMG-TR

SY58052AUMG-TR - 10.7Gbps CML Data-Clock Synchronizer | Microchip

The Microchip Technology SY58052AUMG-TR is an ultra-precision CML data and clock synchronizer (retimer) with internal input and output terminations, supporting a guaranteed maximum data throughput of 10.7 Gbps and a maximum clock frequency of 10.7 GHz, housed in a 16-pin VFQFN (3x3 mm) exposed-pad package. A data-clock synchronizer, also called a retimer, is a high-speed interface IC that regenerates a clean clock from an incoming serial data stream, or resynchronizes data to a reference clock, removing accumulated jitter. Within the signal-chain hierarchy it sits between serializers/deserializers (SerDes), backplane drivers, and clock distribution ICs, and is a critical building block of physical-layer (PHY) conditioning in high-speed serial links. Key features include differential CML inputs with a unique internal termination network accessible through a VT pin, differential CML outputs, and operation from a 2.375 V to 3.63 V supply over the industrial temperature range of -40C to +85C. The internal terminations allow direct interfacing to multiple logic standards, both AC-coupled and DC-coupled, without external resistor-bias or termination networks. Technically, the VT-pin architecture produces a clean, stub-free, low-jitter input interface: termination is realized on-chip, eliminating the parasitic stubs and impedance discontinuities that external discrete termination networks introduce. The CML output stage drives 50-ohm differential transmission lines directly, preserving signal integrity at multi-gigabit data rates on FR-4 backplanes and copper cable assemblies. Typical applications include backplane retiming in telecom and data-communication equipment, retiming after long data transmission in ATM/SONET/SDH systems, and jitter cleanup in 10G serial links, where the part restores data-edge alignment ahead of a SerDes or clock-recovery module. Design consideration: the exposed pad is the main ground and thermal path, so it must be soldered to a solid ground plane with an array of vias; leaving it floating degrades return-loss and jitter performance. This page synthesizes distributor pricing, drop-in same-family alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ پەیوەندی
SY73551LZG - 1:4 LVCMOS Clock Fanout Buffer 8-SOIC | Microchip
SY73551LZG

SY73551LZG - 1:4 LVCMOS Clock Fanout Buffer 8-SOIC | Microchip

The Microchip Technology SY73551LZG is a 1:4 LVCMOS/LVTTL clock fanout buffer delivering four low-skew output copies of a single input clock at speeds up to 160 MHz, supplied in an 8-pin SOIC (3.90 mm width) package. Originally introduced by Micrel Semiconductor under the Precision Edge product line, it operates from a 3.3V ±10% power supply and is guaranteed across the full industrial temperature range of -40°C to +85°C. A clock fanout buffer is a timing-distribution IC that takes one input clock signal and regenerates multiple identical copies with minimal added skew and jitter. In the system hierarchy of clock and timing ICs, fanout buffers sit between the clock source (crystal oscillator, PLL synthesizer, or SoC clock output) and the load devices (FPGAs, ASICs, processors, transceivers), preventing the signal-integrity degradation and loading problems that occur when a single oscillator output drives many destinations directly. Key features of the SY73551L include four LVCMOS/LVTTL-compatible outputs, single-ended input acceptance, and the low additive jitter and tight output-to-output skew required to preserve timing margins in synchronous digital systems. The 8-SOIC footprint keeps the buffer physically close to clock destinations, minimizing trace stub lengths that would otherwise amplify reflections on fast edges. Its wide 3.0V-to-3.6V supply tolerance allows direct connection to common 3.3V rails without a dedicated regulator. Architecturally, the device amplifies and reshapes the input edge to restore full LVCMOS drive levels even when the source has attenuated through PCB routing or series termination. Per the Microchip datasheet, the industrial-grade temperature guarantee means output skew, propagation delay, and duty-cycle specifications remain valid over the entire -40°C to +85°C range, not merely at room temperature. Typical applications include clock distribution to FPGA and DSP banks in industrial control, network interface cards distributing a reference clock to PHY and MAC devices, test and measurement instruments fanning a master clock to multiple converter stages, and telecom line cards. Any synchronous system that drives more than two clock loads from one source benefits from a dedicated fanout buffer. When designing with this part, keep each of the four output traces length-matched and source-terminated, and decouple the 3.3V rail with a 0.1uF ceramic capacitor placed within a few millimeters of the VDD pin. Leave unused outputs properly terminated per the datasheet guidance rather than floating. This page adds distributor context, application guidance, and drop-in alternative analysis that go beyond the raw datasheet content, helping engineers both select the SY73551LZG and qualify substitutes quickly.

RFQ پەیوەندی
Si5365 - Pin-Programmable Precision Clock Multiplier | Skyworks
Si5365

Si5365 - Pin-Programmable Precision Clock Multiplier | Skyworks

The Skyworks Solutions Si5365 is a pin-programmable, low-jitter precision clock multiplier generating any frequency from 2 kHz to 945 MHz (select frequencies to 1.4 GHz) from a 2 kHz to 710 MHz input, housed in a ball-grid-array package with output jitter as low as 290 fs rms (12 kHz to 20 MHz). A precision clock multiplier is a frequency-synthesis IC in the clock generation and timing hierarchy (clock IC -> PLL-based synthesizer -> clock tree -> system timing). Unlike a jitter attenuator, the Si5365 multiplies a reference clock without jitter cleaning, making the input jitter pass through with minimal additive noise from the internal third-generation DSPLL core. Key features include any-frequency synthesis from 2 kHz to 945 MHz with selected outputs reaching 1.4 GHz, ultra-low additive jitter of 290 fs rms over the 12 kHz to 20 MHz band (320 fs rms over 50 kHz to 80 MHz), a fully integrated loop filter that eliminates external VCXO and filter components, and pin-programmable configuration via BWSEL[1:0] and frequency-selection pins, requiring no firmware or serial programming. The device is built on Skyworks (formerly Silicon Laboratories) 3rd-generation DSPLL technology, a digital PLL architecture that integrates the loop filter digitally, giving repeatable, process-independent loop behavior and selectable loop bandwidth from 4 Hz to 525 Hz. Because the configuration is pin-strapped rather than register-based, the clock plan is fixed at power-up, which simplifies bring-up and improves robustness in systems without a management controller. Typical applications include SONET OC-48/OC-192 and SDH STM-16/STM-64 line-card clock multiplication, 10 Gigabit and lower-rate Ethernet PHY reference clocks, Fibre Channel host-bus adapters and storage area network timing, and high-speed backplane and switch-fabric clock distribution where multiplication without jitter attenuation is required. The device meets ITU-T G.8251 and Telcordia GR-253-CORE jitter specifications per the manufacturer data sheet. Designers should verify that the input reference jitter is already within system budget, since the Si5365 deliberately does not attenuate incoming jitter; the integrated loop bandwidth selection trades reference tracking against additive-noise suppression. This page adds engineering value beyond the datasheet by synthesizing drop-in family alternatives, application guidance, and comparison tables in a single citable reference.

RFQ پەیوەندی
Si5366 - 1.05GHz Jitter-Attenuating Clock Multiplier | Skyworks
Si5366

Si5366 - 1.05GHz Jitter-Attenuating Clock Multiplier | Skyworks

The Skyworks (Silicon Labs) Si5366 is a jitter-attenuating precision clock multiplier with four clock inputs from 8 kHz to 707 MHz and five frequency-multiplied outputs from 8 kHz to 1050 MHz, based on third-generation DSPLL technology in a 100-pin TQFP package. A jitter attenuator is a specialized clock IC that cleans reference clocks by phase-locking a low-noise oscillator to a noisy input and filtering the timing jitter inside a narrow bandwidth. Within the clock-management hierarchy (clock generator -> clock multiplier -> jitter attenuator -> timing IC -> signal integrity chain), the Si5366 sits at the critical point where an unstable recovered or reference clock must be converted into a standards-compliant, low-jitter output for high-speed serializers and framer devices. Key features include any-frequency input and output capability across the 8 kHz to 1050 MHz span, DSPLL-based jitter cleaning with selectable bandwidth, support for SONET OC-48/OC-192, 10 Gigabit Ethernet, and Fibre Channel rates, and four independent inputs with automatic or manual failover for redundant clocking. According to the Skyworks datasheet, the device integrates the loop filter and VCO, minimizing external components and board area. The third-generation DSPLL architecture replaces a conventional analog PLL with a digital loop that achieves very low jitter generation and tight output-to-input phase tracking, enabling designs to pass stringent standards such as GR-253 and IEEE 802.3 jitter masks without discrete crystal filtering. Typical applications include SONET/SDH line-card reference clocks at 155.52 MHz, 622.08 MHz, and 2.48 GHz derived rates, 10GbE and Fibre Channel transceiver reference cleaning, and central-office synchronization (BITS/SSU) distribution. Design consideration: supply noise directly modulates the VCO, so use dedicated low-noise LDO supplies and solid ground planes; jitter floor degrades quickly with noisy 3.3 V rails. This page synthesizes distributor pricing, drop-in family alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ پەیوەندی
Si5367 - uP-Programmable Precision Clock Multiplier | Silicon Labs
Si5367

Si5367 - uP-Programmable Precision Clock Multiplier | Silicon Labs

The Silicon Labs Si5367 is a low-jitter, uP-programmable precision clock multiplier that accepts four clock inputs ranging from 10 to 707 MHz and generates five frequency-multiplied clock outputs ranging from 2 kHz to 945 MHz, with select frequencies up to 1.4 GHz, in a TQFP package. A clock multiplier (also called a frequency synthesizer or clock generator) is a timing IC that produces higher-frequency clock signals from a lower-frequency reference. Within the power-management and timing hierarchy, clock multipliers sit alongside jitter attenuators, clock buffers, and oscillators as members of the broader clock and timing IC family. Multipliers differ from jitter cleaners: a multiplier converts frequency without reducing phase noise inherited from the input, whereas a jitter attenuator like the Si5317 actively cleans the clock. The Si5367's headline features include any-rate frequency synthesis via Silicon Laboratories' 3rd-generation DSPLL technology, microprocessor programmability through an I2C or SPI interface, four selectable input references, and five independent outputs. DSPLL integration eliminates the need for an external VCXO and external loop filter components, dramatically reducing board area and BOM count compared with discrete PLL implementations. Architecturally, the third-generation DSPLL implements an all-digital loop that synthesizes the output frequency from a programmable multiplication ratio relative to the selected input. Because both input frequency and multiplication ratio are register-programmable at runtime, a single Si5367 can support multiple line rates and standards in one design, simplifying inventory and enabling field reconfiguration. Typical applications include line-card and network-synchronization clock synthesis in SONET/SDH and Ethernet equipment, frequency translation for FPGA and ASIC reference clocks, and test-and-measurement instrumentation requiring flexible multiplication ratios. Design consideration: since the Si5367 multiplies without jitter attenuation, input jitter transfers to the outputs multiplied by the frequency ratio; use a clean reference or a dedicated jitter attenuator upstream when low-output jitter is critical. This page adds distributor-linked data sources, same-family drop-in alternatives, and practical design notes not consolidated in the manufacturer datasheet.

RFQ پەیوەندی
Si5368 - Sub-1ps Jitter Clock Multiplier | Skyworks
Si5368

Si5368 - Sub-1ps Jitter Clock Multiplier | Skyworks

The Skyworks Solutions Si5368 is a jitter-attenuating precision clock multiplier delivering sub 1 ps rms jitter performance, accepting four clock inputs from 2 kHz to 710 MHz and generating five synchronous outputs from 2 kHz to 945 MHz with select frequencies to 1.4 GHz, housed in a 100-pin TQFP package. A precision clock multiplier/jitter attenuator is a timing IC that takes a noisy or offset-frequency reference clock and synthesizes a new, ultra-clean output clock at virtually any required frequency. Within the system hierarchy, it sits under clock generation and distribution ICs, part of the broader clock and timing category of semiconductors that also includes oscillators, buffers, and frequency translators. Unlike simple PLL multipliers, jitter cleaners use a two-stage architecture with an internal VCXO-style loop to strip reference noise. Key features include any-frequency synthesis from 2 kHz to 945 MHz (select outputs to 1.4 GHz), support for LVPECL, LVDS, CML, and CMOS signal formats on five independent outputs, and holdover and freerun operating modes for reference loss conditions. Four selectable input clocks enable automatic reference switchover in redundant-timing systems. Technically, the Si5368 is built on Silicon Laboratories' third-generation DSPLL technology, which provides any-frequency synthesis and jitter attenuation in a highly integrated PLL that eliminates the need for an external VCXO and loop filter components. This integration reduces board area, BOM cost, and loop-filter tuning effort compared to discrete PLL plus VCXO designs. Typical applications include line-card and optical-transport clock recovery and cleanup for SONET/SDH rates, 10G/40G/100G Ethernet and OTN retiming subsystems, and test-and-measurement instrumentation requiring sub-picosecond clock purity. When designing with the Si5368, follow the manufacturer datasheet recommendations for power-supply filtering of the analog PLL supplies and use a clean reference; jitter attenuation degrades if the loop bandwidth is misconfigured relative to input jitter. This page synthesizes distributor availability, drop-in family alternatives, comparison data, and practical design notes not found in the manufacturer datasheet alone.

RFQ پەیوەندی
Si5369 - Any-Frequency Jitter Attenuating Clock | Skyworks
Si5369

Si5369 - Any-Frequency Jitter Attenuating Clock | Skyworks

The Skyworks Solutions (formerly Silicon Labs) Si5369 is an any-frequency precision clock multiplier and jitter attenuator that generates any frequency from 2 kHz to 945 MHz and select frequencies up to 1.4 GHz from an input frequency of 2 kHz to 710 MHz, housed in a 100-pin TQFP package with jitter generation as low as 300 fs rms. A jitter attenuating clock multiplier (also called a jitter cleaner or precision clock IC) is a phase-locked-loop-based timing device that takes a noisy or frequency-mismatched reference clock and produces one or more ultra-clean output clocks. Within the timing hierarchy, it sits above simple clock oscillators and below full network synchronization modules, combining a digital PLL, integrated VCO, and programmable loop filter in a single clock management IC. Key features include ultra-low jitter generation of 300 fs rms (12 kHz-20 MHz bandwidth on B/D grades), an integrated loop filter with selectable loop bandwidth, and any-frequency synthesis via Silicon Labs' dsPLL architecture that eliminates external VCXO selection. The selectable loop bandwidth allows designers to trade jitter transfer versus jitter tolerance for SONET/SDH, OTN, or Ethernet compliance. Technically, the Si5369 uses a third-generation dsPLL (digitally synthesized PLL) with an integrated low-noise VCO and an on-chip loop filter configurable from tens of Hz to several kHz, removing the need for external loop-filter component design. Frequency plans are computed in-circuit, so a single stock part supports thousands of output/input frequency combinations, reducing BOM proliferation. Typical applications include line-card and transport synchronization in SONET/SDH and OTN equipment, jitter cleaning for 10G/40G Ethernet PHYs, low-jitter clocking for high-speed ADC/DAC converters, and reference distribution in wireless base stations and test instrumentation. A key design consideration is that loop bandwidth selection directly governs jitter transfer: tight bandwidths attenuate input jitter best but increase lock time, so choose the bandwidth setting per the applicable jitter tolerance mask. This page synthesizes distributor pricing, drop-in family alternatives, and practical design notes not found in the manufacturer datasheet alone.

RFQ پەیوەندی