بەرهەمەکان (730+)

MC33XS2410EL - Quad 100mOhm 60V High-Side Switch | NXP
MC33XS2410EL

MC33XS2410EL - Quad 100mOhm 60V High-Side Switch | NXP

The NXP Semiconductors MC33XS2410EL is a four-channel self-protected high-side switch with 100 mOhm per-channel on-resistance, an operating supply range of 3.0 V to 60 V, and SPI control with an embedded 12-bit analog-to-digital converter, housed in a 28-pin HTSSOP (TSSOP-28) package. A high-side switch is a power distribution device placed between a supply rail and a load, switching the positive side of the circuit. Within the power management hierarchy, high-side switches sit under power distribution switches and load drivers, which in turn belong to power management ICs (PMICs). Self-protected smart high-side switches integrate MOSFET power stages with protection and diagnostic functions that would otherwise require discrete MOSFETs, gate drivers, current-sense amplifiers, and supervisory circuitry. Key features of the MC33XS2410EL include four N-channel high-side outputs with 100 mOhm on-resistance, a wide 3.0 V to 60 V supply range that tolerates automotive load-dump transients, an embedded 12-bit ADC for current and voltage monitoring, and SPI-based digital control and diagnostics. Per DigiKey, the device is characterized as a 1:4 N-channel power switch/driver rated at 3.6 A, while Newark lists the family as quad high-side up to 5 A and 60 V depending on configuration. Technically, the high level of integration drastically simplifies hardware design: the embedded 12-bit analog-to-digital converter enables MCU software control of load current diagnostics, output voltage feedback, and fault detection (open load, short circuit, overtemperature) without external sense circuitry. The device has been qualified to appropriate automotive standards per NXP, making it suitable for body control modules and ECU load driving. Typical applications include automotive body control modules driving lamps, relays, and resistive loads; industrial power distribution with remote diagnostics; and ECU-adjacent load management where SPI configurability and ADC-based condition monitoring reduce wiring harness complexity. A key design consideration is thermal management: at 3.6 A through 100 mOhm each channel dissipates roughly 1.3 W, so the HTSSOP-28 exposed-pad package requires adequate PCB copper under the thermal pad. Note that NXP lists this product as NRND (Not Recommended for New Designs). This page synthesizes distributor pricing, lifecycle status, and drop-in alternative guidance not found on the manufacturer product page.

RFQ پەیوەندی
MC33XS2410EL - Quad 100mOhm 60V High-Side Switch | NXP
MC33XS2410EL

MC33XS2410EL - Quad 100mOhm 60V High-Side Switch | NXP

The NXP Semiconductors MC33XS2410 is a four-channel self-protected high-side switch, configurable as quad 100 mOhm or dual 50 mOhm, operating from a 3.0 V to 60 V supply in a 28-pin HTSSOP package with advanced digital monitoring and control via SPI and an embedded 12-bit analog-to-digital converter. A high-side switch is a power semiconductor device placed between a supply rail and a load, switching the positive supply rather than the ground path. Within the power-management hierarchy (switch -> load driver -> power distribution IC -> power management IC), smart high-side switches integrate the power MOSFET, gate driver, charge pump, and protection circuitry in one package, replacing discrete MOSFET plus driver solutions. They report diagnostics such as load current, supply voltage, and fault status back to the microcontroller, enabling predictive maintenance and functional-safety concepts in modern vehicles and industrial systems. Key differentiating features of the MC33XS2410 include its wide 3.0 V to 60 V operating range covering 12 V and 24 V automotive board-net conditions including load-dump transients, a nominal 3.6 A load current rating per the DigiKey listing, and two operating configurations (four 100 mOhm channels or two paralleled 50 mOhm channels). The embedded 12-bit ADC samples channel current and supply voltage on-chip, drastically reducing external sense resistors, amplifiers, and MCU software overhead compared with legacy smart switches. Technically, the device combines N-channel power MOSFETs with integrated gate drive, active clamp, overcurrent, overtemperature, and loss-of-ground protections. Its SPI interface (16-bit) exposes configuration of channel on/off states, open-load detection thresholds in the off state, fault reporting, and ADC readback. Current-sense ratios are reported digitally rather than through an analog sense pin, improving accuracy and eliminating calibration. Typical applications include automotive resistive, capacitive, and inductive loads such as LED lamps, relays, solenoids, heater elements, and small DC motors, plus industrial 24 V PLC output modules where 60 V transient ruggedness is valuable. Design consideration: the 28-HTSSOP exposed-pad package requires a well-soldered thermal pad on the PCB to meet thermal performance; size the copper pour based on worst-case continuous load and RDS(on) dissipation. This page synthesizes distributor pricing, cross-reference guidance, and practical design notes not found in the NXP datasheet alone, with data verified as of 2026-09-14.

RFQ پەیوەندی
MC34710EW - Dual DC-DC + LDO PMIC w/ Sequencing | NXP
MC34710EW

MC34710EW - Dual DC-DC + LDO PMIC w/ Sequencing | NXP

The NXP MC34710EW is a dual-output power management IC integrating a switching regulator, a linear regulator, supervisory and power supply sequencing circuitry, supplied in a 32-pin SSOP exposed-pad package. It operates from a wide 13 V to 32 V input range, delivers 7.5 mA typical quiescent current, and is targeted at embedded MCU power trees for commercial and industrial systems. A PMIC (Power Management IC) is a single-chip device that consolidates multiple power-conversion and supervisory functions - typically one or more switching converters, low-dropout regulators, voltage supervisors, and sequencing logic - into one IC. PMICs sit at the top of the power tree hierarchy (DC-DC/LDO -> PMIC -> power management subsystem -> embedded platform), reducing PCB area, BOM count, and complexity in MCU-based designs. Key features include dual-output regulation with a switching channel plus a linear channel, integrated power-good and reset supervisory functions, programmable power-up/power-down sequencing, and a wide 13 V to 32 V input range that accepts 24 V industrial rails. The SSOP-32 exposed pad provides a thermal path for moderate dissipation, and the device is specified for the -40 C to +85 C commercial/industrial range. Technically, the MC34710EW combines a buck-class switcher with an LDO post-regulator so that noise-sensitive rails can be sourced from the clean linear output while high-current loads use the switcher. Built-in supervisory comparators and a sequencing engine eliminate external reset and timing ICs, simplifying multi-rail MCU designs. Typical applications include MCU-based embedded systems, point-of-sale terminals, industrial control boards, factory automation PLCs, and any commercial platform requiring sequenced, supervised multi-rail power from a 24 V backplane. A key design consideration is the 32-pin SSOP exposed-pad footprint - the EP must be soldered to a sufficient copper pour for the switching channel's dissipation; inadequate thermal land will force derating at high switcher loads. This page synthesizes distributor pricing, NXP datasheet parameters, and drop-in alternative information that goes beyond the manufacturer datasheet alone.

RFQ پەیوەندی
MC34904C5EK - System Basis Chip SBC | NXP | SOIC-32 EP
MC34904C5EK

MC34904C5EK - System Basis Chip SBC | NXP | SOIC-32 EP

The NXP MC34904C5EK is a second-generation System Basis Chip (SBC) for industrial MCUs, integrating two 5.0 V/400 mA LDOs, four wake-up inputs, CAN and LIN/SPI interfaces, watchdog, and battery monitoring in a 32-pin SOIC-EP package. It targets 9V/12V/15V/18V/24V industrial systems with 1 Mbps CAN and full low-power mode management (Sleep, Standby, Normal, Cranking). A System Basis Chip (SBC) is a mixed-signal companion IC that consolidates the discrete power, communication, and supervisory functions surrounding a microcontroller on a single die. It sits above a simple LDO and below a full PMIC in the hierarchy: SBC -> PMIC -> power management IC. By combining multiple voltage regulators, transceivers, and monitoring circuitry in one package, an SBC reduces BOM count, PCB area, and design complexity for automotive and industrial ECUs. The MC34904C5EK integrates two 5.0V/400mA LDO regulators (V1 for MCU and V2 configurable to 5.0V or 3.3V via SPI for peripherals), an auxiliary SPI-configurable 5.0V or 3.3V regulator with overcurrent and undervoltage protection, four high-voltage wake-up inputs capable of supporting both edge and level-sensitive interrupts, and a MUX output pin for internal analog signal and power supply monitoring. The CAN interface supports 1 Mbps operation and LIN/SPI master-slave configuration enables flexible in-system communication. Cranking voltage support down to 3V (typical) keeps the MCU alive during engine cranking transients in 12V systems. Typical applications include industrial CAN nodes and PLC I/O modules, automotive body ECUs needing cranking tolerance, sensor hubs with wake-on-event capability, and battery-backed industrial controllers requiring low-Iq sleep modes. The device is specified for AEC-Q100 environments and 24V industrial bus rails, with operating temperature coverage from -40C to +125C. Key design considerations include thermal management at high ambient enclosures (SOIC-EP exposed pad must be soldered to the ground copper pour) and correct sequencing between V1 and V2 to prevent MCU reset during V2 ramp. The four wake inputs can be configured for rising, falling, or both edges; the MUX output routes battery voltage, V1, V2, or internal references to an external ADC. This page consolidates pricing from NXP authorized distributors, drop-in alternatives from the same MC34903/MC34904/MC34905 SBC family, and engineering design notes beyond those in the manufacturer datasheet.

RFQ پەیوەندی
MC34910BAC - LIN SBC, 5V/60mA LDO, High-Side Drivers | NXP | LQFP-32
MC34910BAC

MC34910BAC - LIN SBC, 5V/60mA LDO, High-Side Drivers | NXP | LQFP-32

The NXP MC34910BAC is a Serial Peripheral Interface (SPI) controlled System Basis Chip (SBC) that combines a LIN 2.1 transceiver, a 5.0V/60mA low-dropout (LDO) voltage regulator, two high-side drivers, and wake-up/interrupt logic in a single 32-pin LQFP (7x7 mm) package. It targets automotive and industrial body-electronics applications where a small MCU must communicate over a LIN bus while being powered from the 12V vehicle battery. The device integrates a precision voltage regulator, physical-layer LIN interface compliant with LIN 2.1, and configurable high-side switches that can drive resistive loads such as lamps or relays up to the rated current. A System Basis Chip (SBC) is a category of mixed-signal power management and communication IC that consolidates what would otherwise be three or four discrete chips - a voltage regulator, a bus transceiver, and high-side driver stages - into a single package. SBCs sit in the vehicle network hierarchy at the edge node, between the LIN/CAN bus and the local microcontroller, and they fall under the broader category of automotive power management ICs (PMICs). By colocating the regulator and the LIN physical layer, an SBC eliminates board space, reduces quiescent current, and simplifies EMC design because the regulated 5V rail used by the MCU stays physically close to its supply pins. Key features of the MC34910BAC include a wide VBAT operating range suitable for direct connection to the automotive 12V bus, a low standby current that supports battery-friendly sleep modes, programmable watchdog and reset generation for the host MCU, ESD robustness on the LIN pin enhanced to meet IEC 61000-4-2 gun-test contact discharge, and configurable high-side outputs that can be PWM-driven for dimming or load management. The SPI interface allows the host microcontroller to read diagnostic status, control the high-side switches, configure wake-up sources, and manage the device's sleep transitions. The integrated 5V LDO delivers up to 60 mA to power the host MCU and small peripheral circuitry. Architecturally, the MC34910BAC uses a high-side DMOS topology for the power outputs, a bandgap-referenced regulator for the 5V rail, and a LIN physical layer that meets the LIN 2.1 standard. An internal state machine handles bus wake-up detection and cyclic sense capability so the device can wake the system when the main regulator is otherwise disabled, dramatically reducing quiescent current in always-connected body modules. Typical applications include automotive body control modules, HVAC panel controllers, door/window lift modules, seat controllers, mirror adjusters, and LIN slave nodes for interior lighting. Industrial LIN-based sensor nodes and small appliance controls also benefit from the integrated LIN + LDO + driver combination. The 32-pin LQFP package gives adequate thermal headroom for the high-side drivers and supports both hand and automated assembly. When designing with the MC34910BAC, allocate sufficient copper pour under the exposed thermal pad and on the high-side output traces to dissipate load current, place the VBAT bypass capacitor as close as possible to the supply pin to handle LIN bus ESD transients, and configure the SPI watchdog and reset timing to match the host MCU's startup latency. Selecting the correct LQFP-32 variant within the MC34910 family tree (BAC vs G5) determines which high-side driver topology and current ratings you get; the MC34910BAC specifically provides the configuration shown in this datasheet.

RFQ پەیوەندی
MCP14A0454T-E/SN - 4.5A Dual MOSFET Gate Driver | Microchip
MCP14A0454T-E/SN

MCP14A0454T-E/SN - 4.5A Dual MOSFET Gate Driver | Microchip

The Microchip Technology MCP14A0454T-E/SN is a high-speed dual low-side MOSFET gate driver delivering up to 4.5A of peak output current per channel while operating from a single 4.5V to 18V supply. Packaged in an 8-pin SOIC (SN), this tape-and-reel variant features dual non-inverting outputs with matched rise and fall times, making it well suited for driving power MOSFETs and IGBTs in compact power conversion designs. A MOSFET gate driver is a power buffer stage that converts logic-level PWM signals into high-current gate drive signals capable of rapidly charging and discharging the gate capacitance of power semiconductors. Within the power management hierarchy, gate drivers sit between PWM controllers or microcontrollers and power MOSFETs, ensuring fast, clean switching that minimizes switching losses and thermal stress. Low-side drivers such as the MCP14A0454 control transistors referenced to ground. Key features include the 4.5A peak drive current, wide 4.5V to 18V operating supply, low shoot-through current for reduced cross-conduction losses, and matched output impedance for symmetric switching. The low-threshold input logic interface accepts TTL and CMOS signal levels, and the family offers an enable function for power sequencing and shutdown control. According to the Microchip datasheet (DS20005985A), the MCP14A0453/4/5 family shares the same die and package with three output polarity configurations: dual inverting (MCP14A0453), dual non-inverting (MCP14A0454), and complementary (MCP14A0455). Typical applications include switch-mode power supplies (SMPS), motor control circuits, DC-DC converter primary-side switching, Class-D audio amplifier output stages, and general-purpose low-side MOSFET/IGBT driving in industrial and consumer equipment. The dual-channel architecture lets one device drive both switches of a push-pull or half-bridge-referenced stage. Design tip: place a low-ESR ceramic decoupling capacitor (1 uF to 10 uF) directly across VDD and GND to supply the high peak gate currents; otherwise supply sag degrades switching speed and increases EMI.

RFQ پەیوەندی
MCP14A0902-E/MSVAO - 9A MOSFET Driver, MSOP-8 | Microchip
MCP14A0902-E/MSVAO

MCP14A0902-E/MSVAO - 9A MOSFET Driver, MSOP-8 | Microchip

The Microchip Technology MCP14A0902-E/MSVAO is a high-speed, dual-output non-inverting MOSFET gate driver capable of sourcing/sinking up to 9.0 A peak current from a single 4.5 V to 18 V supply, housed in an 8-pin MSOP (MS) package. It is the automotive/VQA-validated (-VAO suffix) variant of the MCP14A0902 family with a low-threshold input stage and an active-high enable pin for sequenced power-up. The non-inverting MCP14A0902 pairs with the inverting MCP14A0901 to provide polarity-flexible half-bridge and synchronous-rectifier drive solutions. A MOSFET gate driver is a specialized power-management IC that sits between a low-power control signal (from a microcontroller, PWM controller, or logic gate) and the gate of a power MOSFET. By providing high peak gate current, gate drivers drastically reduce transition losses in switching converters, motor drives, and Class-D audio stages. Within the broader hierarchy, MOSFET drivers belong to the gate-driver family under Power Management, sitting between analog controllers and the discrete power transistors they switch. Key features include 9.0 A peak output drive current, low shoot-through current, fast rise/fall times, matched propagation delays between the two output channels, an enable pin for shutdown management, and a TTL/CMOS-compatible low-threshold input. The wide 4.5 V to 18 V supply range suits both 5 V logic rails and 12 V bus systems, while the small MSOP-8 footprint enables compact high-density layouts. The device uses a CMOS push-pull output stage with internal logic-level translation, allowing a 3.3 V microcontroller to drive the gate of a 12 V N-channel MOSFET without level shifters. The matched propagation delay between channels minimizes dead-time in synchronous-rectifier and half-bridge topologies, while the 9 A peak current quickly charges large gate charges (Qg) typical of high-current MOSFETs. Typical applications include DC-DC converter synchronous rectification, low-side and high-side MOSFET switching in motor control, Class-D audio amplifiers, power-supply OR-ing FET control, and high-current solenoid/relay drivers. The -VAO suffix indicates Microchip automotive-grade qualification, making it suitable for AEC-Q100-targeted designs. When laying out the PCB, keep the driver within 10 mm of the MOSFET gate to minimize parasitic inductance, and place a 1 V-tze ceramic bypass capacitor close to the VDD pin. If using the enable pin for sequencing, add a 100 kV pull-down to define a default-off state during power-up glitches. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the standalone Microchip datasheet, giving engineers a single decision-grade reference for sourcing and applying the MCP14A0902-E/MSVAO.

RFQ پەیوەندی
MCZ33812EKR2 - Engine Control Analog Power IC, SOIC-32 EP | NXP
MCZ33812EKR2

MCZ33812EKR2 - Engine Control Analog Power IC, SOIC-32 EP | NXP

The NXP MCZ33812EKR2 is an engine control analog power IC designed for single/dual cylinder small engine control applications, packaged in a 32-pin SOIC-EP (exposed pad) thermal-enhanced outline. The device integrates multiple functions required for electronic fuel injection (EFI) and ignition control, including a VCC regulator, an ignition pre-driver, an injector driver, and protective features. Operating from a supply voltage of up to 36 V, the IC serves as the central analog power management and switching element on the engine control module (ECM). An engine control analog power IC is a highly integrated mixed-signal component that conditions battery voltage, drives actuators, and provides protection for the analog and digital engine control circuitry. Within the broader NXP automotive portfolio, the MCZ33812 family sits under the powertrain IC category, which itself derives from power management ICs. The integration reduces the BOM of a complete EFI ECU by replacing dozens of discrete transistors, gate drivers and protection diodes, while providing automotive-grade reliability for harsh under-hood environments. Key features of the MCZ33812EKR2 include an internal 5 V VCC regulator capable of supplying the microcontroller, a high-current injector driver for solenoid actuation, a dedicated ignition pre-driver that interfaces with an external IGBT, an over-temperature shutdown circuit, and load-dump transient protection rated to 14 V supply compatibility. The SOIC-32 EP package exposes the die backside for direct PCB solder attachment, lowering thermal resistance and supporting continuous high-current operation of the injector driver stage. Architecturally, the IC combines a charge pump for the high-side driver rail, separate analog and digital grounds, and CMOS logic inputs that interface directly with a 3.3 V or 5 V MCU. The combination of monolithic integration and ruggedized outputs simplifies PCB layout of motorcycle ECUs and similar small-engine controllers, particularly where board area and component count are constrained. Typical applications for the MCZ33812EKR2 include small motorcycle EFI engine control units, single-cylinder scooter fuel injection modules, dual-cylinder ATV engine controllers, and generic two-wheeler ignition controllers. It also fits auxiliary automotive loads that require a high-side/low-side driver pair with on-board regulation. When designing with this IC, the engineer should observe the layout guidelines for the SOIC-32 EP thermal pad: the exposed pad must be soldered to a copper area of at least 1 square inch to stay within the thermal budget when the injector driver carries continuous current. Decoupling capacitors should be placed as close as possible to the VCC and VBAT pins, and the ignition IGBT must be located within 50 mm of the ignition pre-driver output to limit parasitic inductance. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

RFQ پەیوەندی
MCZ33903CP3EKR2 - SBC Gen2 CAN/LIN 32-SOIC-EP | NXP
MCZ33903CP3EKR2

MCZ33903CP3EKR2 - SBC Gen2 CAN/LIN 32-SOIC-EP | NXP

The NXP (formerly Freescale) MCZ33903CP3EKR2 is a second-generation System Basis Chip (SBC) integrating a high-speed CAN transceiver, a LIN transceiver, a 5.0 V / 3.3 V LDO voltage regulator for MCU supply, and protection circuitry in a single 32-pin SOIC package with an exposed thermal pad. The device targets automotive and industrial network node applications where PCB area, component count, and reliability targets must all be minimized simultaneously. A System Basis Chip (SBC) is an integrated circuit that combines multiple power, communication, and protection functions traditionally implemented as discrete blocks. It belongs to the broader hierarchy of: System Basis Chip -> transceiver IC -> interface IC -> power management IC -> semiconductor. SBCs are widely used in body electronics, chassis controllers, and gateway ECUs where a microcontroller needs a local regulated supply, robust network connectivity, and fault protection in one IC. Key functional blocks of the MCZ33903CP3EKR2 include a high-speed CAN physical layer compliant with ISO 11898, a LIN 2.x physical layer, an MCU-supply LDO selectable between 5.0 V and 3.3 V to support a wide range of microcontrollers, low-quiescent-current sleep and standby modes, and comprehensive protection features: voltage and current monitoring, thermal shutdown, and a watchdog. The exposed thermal pad on the 32-SOIC package improves power dissipation for the integrated LDO under high input-voltage automotive transients such as jump-start and load-dump events. Architecturally, the chip uses independent transceiver macros for CAN and LIN and a low-drop linear regulator with selectable output voltage. Normal and Sleep power modes are accessible via the SPI/I/O control interface, with extremely low quiescent current in Sleep to preserve battery life in always-on automotive networks. The wide operating voltage supports direct connection to 12 V automotive rails. Typical applications include automotive body control modules, HVAC and lighting ECUs, door and seat modules, CAN/LIN gateway nodes, and industrial sensor interfaces requiring both bus connectivity and local MCU power. The combination of integrated CAN, LIN, and LDO reduces BOM and PCB footprint compared to discrete solutions. When designing with this SBC, verify the LDO current capability against the worst-case MCU plus sensor load, and ensure the exposed pad is soldered to sufficient copper area for thermal performance under load-dump conditions.

RFQ پەیوەندی
MCZ33905BS5EKR2 - 5V CAN+LIN System Basis Chip | NXP
MCZ33905BS5EKR2

MCZ33905BS5EKR2 - 5V CAN+LIN System Basis Chip | NXP

The NXP MCZ33905BS5EKR2 is a 5 V System Basis Chip (SBC) with a high-speed CAN (HSCAN) transceiver, a single-wire LIN interface, and an integrated 5 V/250 mA low-dropout (LDO) regulator, housed in a 32-pin HSOP (32-SOIC-EP) package with an exposed thermal pad. Designed around NXP's SMPS-based SBC architecture, it operates from a 5.5 V to 28 V supply (with load-dump survival typical of automotive 12 V rails) and targets body-electronics and chassis networking. What is an SBC? A System Basis Chip integrates a CAN/LIN physical layer, a voltage regulator, reset circuitry, and watchdog logic that were historically implemented as discrete components. Sitting between the 12 V bus and an MCU, an SBC reduces PCB area, simplifies EMC filtering, and provides deterministic power-up sequencing required for automotive microcontrollers. Key features include an internal 5 V LDO rated for 250 mA, a full ISO 11898-5 compliant CAN transceiver with bus fault protection, a single-wire LIN 2.x interface, a reset output with adjustable threshold, a watchdog timer windowed to the MCU, and a low-power Sleep mode with wake-on-CAN/LIN capability. The exposed pad (EP) on the 32-SSOP/HSOP body reduces thermal resistance and supports sustained current on the 5 V rail at elevated ambient temperatures. Typical applications are automotive body controllers, instrument clusters, HVAC panels, seat and mirror modules, lighting ECUs, and gateway nodes bridging CAN and LIN subnets. The wide 5.5 V to 28 V operating window absorbs cranking and load-dump transients seen on 12 V automotive rails, eliminating the need for an external pre-regulator. When laying out this SBC, keep the high-current ground return under the exposed pad stitch directly to the chassis ground plane with multiple vias; place the 5 V output bypass within 5 mm of the VCC_HV pin to suppress switching residual. This page synthesizes distributor pricing, drop-in alternatives drawn from NXP's SBC portfolio and qualified cross-brand sources, and practical design notes not found on the manufacturer product page alone.

RFQ پەیوەندی
MIC2005A-1YM5-TR - 500mA High-Side Power Switch SOT-23-5 | Microchip
MIC2005A-1YM5-TR

MIC2005A-1YM5-TR - 500mA High-Side Power Switch SOT-23-5 | Microchip

The Microchip Technology MIC2005A-1YM5-TR is a single-channel, current-limiting, high-side P-channel MOSFET power distribution switch rated for 500 mA continuous load current in a 5-pin SOT-23-5 surface-mount package. It operates from a 2.5 V to 5.5 V input rail, integrates a 70 mΩ (typical) P-channel MOSFET pass element, and provides a factory-set 500 mA current limit with automatic fault blanking. According to the manufacturer datasheet, the device features a /FAULT open-drain indicator that asserts low approximately 32 ms after a sustained over-current or short-circuit event, allowing the system to ignore transient inrush spikes. A high-side power switch (also called a USB power switch or load switch) is a MOSFET-based circuit that sits between the upstream DC rail and the downstream load. Its job is to distribute power, protect the load and the wiring from over-current events, and provide a clean, controlled turn-on. The high-side switch sits between the supply and the load (versus a low-side switch which sits between load and ground), preserving the ground reference of the downstream circuit. In the power management hierarchy, high-side switches fall under power distribution ICs, which themselves sit under power management ICs and the broader semiconductor category. Key features of the MIC2005A-1YM5-TR include thermal-shutdown protection, under-voltage lockout (UVLO), output slew-rate limiting, an active-high enable input for sequencing or push-button control, and a fixed (non-adjustable) current-limit threshold of 500 mA. The part is offered in tape-and-reel packaging (-TR suffix) for high-volume assembly and is qualified over the -40 °C to +85 °C industrial temperature range. Because the current limit is fixed, no external sense resistor is required - this simplifies BOM and reduces PCB area. The internal architecture combines a P-channel power MOSFET, a precision current-sense and comparator block, a charge-pump driver for the MOSFET gate, and digital control logic for the enable, fault, and blanking functions. The 70 mΩ on-resistance at 5 V keeps conduction losses low - even at 500 mA, the drop across the switch is only about 35 mV. Fault blanking prevents nuisance tripping during capacitive-load inrush or USB hot-plug events, while thermal shutdown protects the die if sustained overload drives the junction temperature above the safe limit. Typical applications include USB port power switching in hubs, set-top boxes, and printers; high-side load switching in digital televisions (DTV), personal digital assistants (PDAs), and other peripherals; and any system that needs a single 5 V rail switch with built-in current limit and fault reporting. The MIC20XX family is also commonly used to power individual downstream rails in multi-rail systems where each rail needs independent protection. Compared to discrete MOSFET + comparator solutions, the MIC2005A-1YM5-TR saves board space and design time by integrating the FET, sense element, and protection logic in one 5-pin SOT-23. When designing with this part, pay attention to the input capacitor - Microchip recommends a 1 µF low-ESR ceramic directly on IN to handle load-step transients and stabilize the internal charge pump. The /FAULT pin requires a pull-up resistor (typically 10 kΩ to 100 kΩ) because it is an open-drain output. Layout should keep the high-current OUT trace short and wide to minimize parasitic inductance. This page synthesizes distributor pricing, same-family drop-in alternatives, and practical design notes not found in the manufacturer datasheet. For full electrical characteristics and curves, refer to the official Microchip MIC20XX datasheet.

RFQ پەیوەندی
MIC2005A-1YM6-TR - 500mA High-Side P-Channel Power Switch | Microchip
MIC2005A-1YM6-TR

MIC2005A-1YM6-TR - 500mA High-Side P-Channel Power Switch | Microchip

The Microchip Technology MIC2005A-1YM6-TR is a single-channel, current-limiting, high-side P-channel MOSFET power distribution switch rated for 500 mA continuous load current, housed in a 6-pin SOT-23 package. It accepts input voltages from 2.5 V to 5.5 V and provides a fixed 500 mA current limit with an active-high enable input for power sequencing and load control. A high-side power switch is an integrated load-switch IC that sits between a power rail and the downstream load, replacing a discrete P-channel MOSFET plus current-sense resistor plus control circuitry with a single component. It belongs to the broader power-management IC hierarchy: power switch -> load switch -> power distribution switch -> power management IC. High-side switches offer reverse-current blocking and ground-referenced load control, simplifying USB port power, hot-plug rails, and battery protection circuits. Key features include 500 mA fixed current limit, low quiescent current, fault flag output for overcurrent reporting, thermal shutdown protection, and undervoltage lockout. The internal P-channel MOSFET provides low on-resistance to minimize voltage drop and conduction loss, while internal slew-rate control limits inrush current during turn-on. The active-high enable pin allows logic-level control from a microcontroller GPIO. Architecturally, the MIC2005A integrates a P-channel pass FET, a current-sense comparator, a fault timer with blanking, and a thermal shutdown block on a single CMOS die. The fault blanking circuit prevents nuisance tripping from load transients, while the thermal shutdown latches off the FET when junction temperature exceeds safe limits. The device is offered in a 6-pin SOT-23 package that occupies approximately 9 mm² of board area, making it suitable for space-constrained portable designs. Typical applications include USB port power distribution, hot-swap peripherals, set-top boxes, digital televisions, printers, notebook PCs, and PDA accessories. The 500 mA current limit aligns with USB 2.0 downstream port requirements, making this part particularly attractive for legacy USB power-switching functions. When designing with this device, place the input bypass capacitor as close as possible to the VIN pin and ensure the output capacitor does not exceed the datasheet maximum to prevent false fault triggering. The fault output is open-drain and requires a pull-up resistor. This page synthesizes distributor pricing, drop-in alternatives drawn from the Microchip MIC20XX family, and practical design notes that complement the manufacturer datasheet.

RFQ پەیوەندی
MIC2005A-2YM6-TR - 500mA High-Side USB Power Switch SOT-23-6 | Microchip
MIC2005A-2YM6-TR

MIC2005A-2YM6-TR - 500mA High-Side USB Power Switch SOT-23-6 | Microchip

The Microchip MIC2005A-2YM6-TR is a 500 mA current-limited, high-side P-channel MOSFET power distribution switch housed in a 6-pin SOT-23-6 surface-mount package, designed for self-powered and bus-powered USB applications and general 5 V power switching. A USB high-side power switch is a type of load switch that sits between a system power rail (typically 5 V) and a downstream USB port or peripheral. Its role is to turn the rail on or off under logic control, present a defined upstream current to the host, and protect both the host and the device from over-current, short-circuit, and inrush events. The MIC20XX family sits within the broader power management IC hierarchy of load switches -> power distribution switches -> USB switches -> power management ICs, complementing LDOs and DC-DC converters on the power tree. Key features include a fixed 500 mA current limit, a 2.5 V to 5.5 V input operating range, low quiescent current, integrated soft-start to control inrush current, an active-high enable input, fault-flag output for over-current and thermal events, under-voltage lockout, and thermal shutdown. Typical on-resistance is approximately 70 mΩ at 5 V, providing low dropout and minimal power dissipation in normal operation. The device requires no external MOSFET, sense resistor, or current-setting network. The MIC2005A-2YM6-TR is the -2 active-high enable variant of the family and ships on tape-and-reel for high-volume assembly. Its small SOT-23-6 footprint, integrated protection, and minimal external BOM make it well suited to compact, cost-sensitive 5 V rails such as USB ports, HDMI ports, and downstream power connectors on consumer and computing platforms. Typical applications include USB 2.0 downstream ports on PCs and laptops, HDMI link power switching, set-top boxes, printers, digital televisions, and any port that needs self-powered or bus-powered current limiting. Pair the MIC2005A-2YM6-TR with an upstream 5 V LDO or buck regulator and follow the datasheet bulk-capacitor guidance to remain USB 2.0 compliant under load steps. When designing with this device, place the input and output bulk capacitors as close as possible to the IC and observe the datasheet derating curve for short-circuit and over-current behavior. Thermal layout is straightforward because typical load currents are 500 mA or less, but continuous fault conditions must be considered. This page combines verified distributor pricing, drop-in alternatives from the same MIC20XX family and competing vendors, and practical PCB design notes not bundled in the manufacturer datasheet, giving a faster engineering decision path than scanning individual distributor listings.

RFQ پەیوەندی
MIC2026-2YM - Dual USB High-Side Power Switch 1.25A 8-SOIC
MIC2026-2YM

MIC2026-2YM - Dual USB High-Side Power Switch 1.25A 8-SOIC

The Microchip Technology MIC2026-2YM is a dual-channel, high-side N-channel MOSFET power distribution switch rated for 1.25A continuous load current per channel in an 8-pin SOIC package. It operates from a 2.7V to 5.5V input rail and integrates current limiting and thermal shutdown to protect the load and the upstream supply. The MIC2026-2YM variant uses an active-low enable input, which is the inverse-polarity control used by the MIC2026 family. A high-side power switch (also called a load switch or power distribution switch) sits between the system rail and a downstream load (USB port, fan, LED string, peripheral). It replaces a discrete P-MOSFET plus fuse/reset circuit by combining an N-channel MOSFET with a charge pump, current-limit comparator, and thermal protection in a single IC. High-side switches sit on the positive rail, so they cut return-path current cleanly and are preferred for hot-plug safety, inrush limiting, and per-port power budgeting. Key features of the MIC2026-2YM include 1.25A continuous output current per channel, internal current limiting, soft-start to suppress inrush transients, and an over-temperature latch that removes the output until the fault clears. The device also provides a fault flag output for system monitoring and ground-loop-tolerant switching. Together these features support USB 2.0 downstream ports, hot-swap bays, and any general-purpose 5V load that benefits from circuit-breaker-style protection. The MIC2026-2YM is internally current limited and thermally protected, and it integrates two switches in one SOIC-8, halving the board area versus two single-channel MIC2025-class parts. The dual-channel topology is also ideal for paired loads such as dual USB ports or two peripheral rails that must power up or fault together. Typical applications are dual USB power distribution, hot-swap 5V cards, and protected fan/LED rails in desktops, docking stations, and embedded computing platforms. The wide 2.7V to 5.5V input range maps directly onto the standard 3.3V and 5V system rails used in these systems. When laying out the MIC2026-2YM, keep input and output capacitors within 2 mm of their respective pins to suppress the inrush spike, and stitch a continuous ground plane under the exposed pad area to spread heat. The fault pin can be left floating if not used, but routing it to a GPIO is recommended for proper diagnostics. This page synthesizes distributor pricing, drop-in alternatives, and application-level design notes that are not aggregated in the manufacturer datasheet.

RFQ پەیوەندی
MIC2091-1YM5-TR - 100mA High-Side Power Switch | Microchip
MIC2091-1YM5-TR

MIC2091-1YM5-TR - 100mA High-Side Power Switch | Microchip

The Microchip Technology MIC2091-1YM5-TR is a 100 mA high-side P-channel MOSFET power distribution switch in a 5-pin SOT-23-5 package, optimized for general-purpose low-power distribution in circuits requiring accurate over-current limiting and circuit protection. The device operates from a 1.8 V to 5.5 V input rail, includes a 1300 mOhm typical on-resistance, and integrates thermal shutdown at 150 °C and undervoltage lockout with 100 mV hysteresis for robust fault handling. A high-side power switch is a load-management building block that sits between a system supply rail and a downstream load, providing controlled turn-on, current limiting, and fault isolation. Within the broader power-management taxonomy, it sits between simple load switches and full hot-swap controllers, offering a middle ground for USB ports, portable devices, and other sub-500 mA distribution rails. The MIC2091-1YM5-TR belongs to the auto-retry current-limit family (the MIC2091-2 variant latches off), and includes a dedicated active-high fault output. Key features include a 1.8 V to 5.5 V operating input range, factory-trimmed 100 mA current limit, active-high logic enable, open-drain fault flag with 10 ms deglitch filter to suppress false trip events, and a junction operating temperature range of -40 °C to +125 °C. The 5-pin SOT-23 footprint occupies just 2.9 mm x 1.6 mm, freeing board area for dense portable designs. According to the Microchip datasheet DS20006611A, the on-resistance rises with temperature and the part includes built-in soft-start to limit inrush current on hot-plug events. Technically the device integrates a charge pump that drives the P-channel gate above VIN for true rail-to-rail load control, while the current-limit loop monitors a sense-FET and modulates gate drive to regulate load current at the programmed limit. The result is predictable behavior across temperature and supply, and clean recovery from momentary overloads without latch-up that would require a power cycle. Typical applications include USB 2.0 downstream port power switching, self-powered and bus-powered USB hubs, notebook and tablet accessory rails, and protection of camera modules, thermal print heads, and other peripheral loads. When designing with this part, place a 1 µF or greater ceramic bypass capacitor on VIN and keep the trace from the device ground pin short and direct to the system ground plane to ensure clean current-limit operation.

RFQ پەیوەندی
MIC2514BM5 - IttyBitty High-Side Switch, SOT-23-5 | Microchip
MIC2514BM5

MIC2514BM5 - IttyBitty High-Side Switch, SOT-23-5 | Microchip

The Microchip Technology MIC2514BM5 is an integrated high-side power switch combining a TTL-compatible input with a protected P-channel MOSFET in a compact 5-pin SOT-23-5 package, with an operating temperature range of -40C to +85C. Originally introduced by Micrel Semiconductor (now part of Microchip Technology), it replaces a discrete high-side driver plus MOSFET combination in low-voltage applications. A high-side switch is a power switching device placed between the supply rail and the load, controlling power delivery by switching the positive supply rather than the ground path. High-side switching is preferred in automotive, industrial, and portable systems because a switched-off load remains referenced to ground, avoiding ground-float faults and simplifying fault diagnostics. The MIC2514 belongs to the power management IC category, sitting within load-switch and hot-swap protection devices under semiconductor power control. Key features include the integrated protected P-channel MOSFET output stage, a TTL-compatible logic input that interfaces directly with microcontroller GPIO or logic-level control signals, and integrated protection functions that reduce external component count. The IttyBitty SOT-23-5 package occupies minimal board area, making the part attractive where a discrete solution would need several square millimeters of PCB space plus placement and routing overhead. Technically, the P-channel MOSFET architecture allows the switch to be turned on by pulling the control input low relative to the input supply, with internal charge or level-shift circuitry handling the gate drive. The protection circuitry guards against fault conditions that would otherwise destroy a discrete MOSFET without driver supervision. Because it switches the positive rail, the part eliminates the need for a separate gate-drive supply or charge pump that an N-channel high-side solution would require at these low voltages. Typical applications include USB and peripheral port power switching, low-voltage load switching in battery-powered portable equipment, and replacing discrete driver-plus-MOSFET high-side configurations in low-voltage industrial boards. When designing with the MIC2514BM5, verify the continuous load current, on-resistance, and fault-protection thresholds against the manufacturer datasheet, as these determine thermal rise and protection timing in the end application. This page synthesizes verified distributor data, drop-in alternative guidance, datasheet sourcing, and practical design notes not consolidated in the manufacturer datasheet alone.

RFQ پەیوەندی
MIC4120YML-TR - 6A Low-Side MOSFET Gate Driver | Microchip
MIC4120YML-TR

MIC4120YML-TR - 6A Low-Side MOSFET Gate Driver | Microchip

The Microchip Technology MIC4120YML-TR is a 6 A peak non-inverting low-side MOSFET gate driver IC in an 8-pin MLF (2x2 mm) surface-mount package, supplied on tape and reel. A low-side MOSFET driver is a power-management interface IC that translates logic-level control signals into the high-current gate charge and discharge currents needed to rapidly switch power MOSFETs referenced to ground. Within the signal-chain hierarchy, it sits between a PWM controller or microcontroller GPIO and the power MOSFET gate, providing voltage regulation-independent drive strength that logic outputs alone cannot deliver. Key features include 6 A peak output current capable of driving the largest MOSFETs with an improved safe operating margin, logic-compatible input thresholds accepting any input from 2.4 V to VS without external speed-up capacitors or resistor networks, and negative input voltage protection of up to 5 V below ground. The non-inverting output polarity simplifies firmware development compared with inverting driver alternatives. Architecturally, the MIC4120 is an improved version of the popular MIC4420, incorporating proprietary input circuits that tolerate input undershoot and latch-up-resistant output stages. These circuits protect against damage from electrostatic discharge and electrical overstress, making the part tough and efficient in demanding switching environments. The MLF package offers low inductance for fast gate-current delivery. Typical applications include switch-mode power supplies, DC-DC converter primary-side switching, motor drive gate interfaces, and class-D amplifier output stages where high peak gate current shortens switching transitions and reduces switching losses. Design consideration: keep the driver gate trace short and place a low-ESR decoupling capacitor close to the supply pin, because 6 A peak gate currents can induce significant ground bounce in long loops. This page synthesizes distributor pricing, drop-in alternatives, pinout guidance, and practical design notes not found in the manufacturer datasheet alone.

RFQ پەیوەندی
MIC4420BN - 6A Peak Low-Side MOSFET Driver | Microchip
MIC4420BN

MIC4420BN - 6A Peak Low-Side MOSFET Driver | Microchip

The Microchip Technology MIC4420BN is a single-channel low-side MOSFET gate driver IC delivering 6 A peak output current in an 8-pin PDIP through-hole package. It is a non-inverting driver fabricated on a bipolar/CMOS/DMOS process and operates from a 4.5 V to 18 V supply. According to the manufacturer datasheet, the device is capable of 6 A peak output and can drive the largest MOSFETs with low switching losses. A low-side gate driver (also called a non-inverting MOSFET driver) is a power-management building block that sits between a low-power control signal (typically from a microcontroller or PWM controller) and the gate of a power MOSFET. Its job is to translate a logic-level PWM input into a high-current drive that can rapidly charge and discharge the MOSFET's gate capacitance, slashing switching losses and eliminating the need for the controller to source/sink gate current directly. Gate drivers belong to the broader power-management IC family and sit alongside voltage regulators, supervisors, and motor drivers. Key features of the MIC4420BN include a 4.5 V to 18 V supply range, can-to-margin switching speeds with typical rise/fall times in the nanosecond range, and matched propagation delays between the input and output edges. The driver is rated for 6 A peak output current both sourcing and sinking, allowing it to handle high gate-charge MOSFETs at high PWM frequencies. The bipolar/CMOS/DMOS process combines low quiescent current with high peak-current capability and rugged latch-up immunity. Typical applications include switch-mode power supplies, motor-drive half-bridge low-side drivers, solenoid drivers, and Class D audio amplifier output stages. Because the part is non-inverting, it can drop into circuits designed around the ubiquitous TC4420 footprint without changing the logic polarity, making it a popular first-pass driver in power designs.

RFQ پەیوەندی
MIC4426YN - Dual 1.5A Inverting MOSFET Driver | Microchip
MIC4426YN

MIC4426YN - Dual 1.5A Inverting MOSFET Driver | Microchip

The Microchip (Micrel) MIC4426YN is a dual 1.5A-peak low-side MOSFET gate driver fabricated on a BiCMOS/DMOS process for low power consumption and high efficiency, supplied in an 8-pin PDIP (0.300 inch, 7.62 mm) through-hole package. It delivers two inverting drivers that translate TTL or CMOS input logic levels to output voltage swings within 25 mV of either the positive supply rail or ground, and it operates from a 4.5 V to 18 V supply with a typical propagation delay of 17 ns. What is a low-side MOSFET driver? A low-side gate driver is a power-management IC that sits between a low-power logic signal (microcontroller PWM output, comparator, or logic gate) and the gate of a power MOSFET or IGBT. Because the driver can source and sink large peak currents (1.5 A in the case of the MIC4426YN), it charges and discharges the MOSFET gate capacitance far faster than the logic device can on its own, slashing switching losses and reducing heat in switch-mode power supplies, motor half-bridges, and pulsed-load circuits. In the broader taxonomy, low-side drivers are a sub-category of gate drivers, which sit under power management and semiconductor ICs. Key features include 1.5 A peak output current per channel, matched rise and fall times for low distortion, 25 mV maximum output offset from either rail, an input threshold that is independent of supply voltage, 6 pF typical input capacitance, and -5 V ESD protection on logic inputs. The driver withstands up to 500 mA of reverse current in either polarity without latching and survives 5 V noise spikes on the ground pin, giving it the ruggedness expected of an industrial-grade driver. Architecturally, the MIC4426YN uses a BiCMOS/DMOS output stage that combines bipolar input logic with DMOS power transistors. This topology achieves the 25 mV rail-to-rail swing that comparable bipolar drivers cannot reach - bipolar parts typically swing only to within 1 V of the rails - and it does so while drawing microamp quiescent current. Two independent inverting channels share bias and protection but otherwise operate without mutual interference. Typical applications include switch-mode power supply (SMPS) synchronous-rectifier gates, DC-DC converter MOSFET drive, motor-driver low-side switches, solenoid and relay coil drivers, line drivers for pulse transformers, and level-shifted interfaces to power MOSFETs in industrial and telecom equipment. The 18 V supply ceiling comfortably drives standard 12 V logic-level and -10 V/-12 V threshold MOSFETs. For design success, place a 1 uF or larger low-ESR bypass capacitor within 1 cm of the VDD pin to keep the high-peak current transients off the upstream supply; otherwise the driver can pull the rail low enough to reset adjacent logic. Keep input traces short and away from switching nodes to avoid false triggering from drain-voltage coupling. This page synthesizes distributor pricing, drop-in pin-compatible alternatives, datasheet-derived specifications, and practical design notes that go beyond what the manufacturer datasheet alone provides.

RFQ پەیوەندی
MIC4451YN - 12A Inverting Low-Side MOSFET Driver | Microchip
MIC4451YN

MIC4451YN - 12A Inverting Low-Side MOSFET Driver | Microchip

The Microchip Technology MIC4451YN is a CMOS inverting low-side gate driver that delivers 12 A peak output current in an 8-pin PDIP through-hole package. It accepts logic-level inputs from 2.4 V up to the supply rail (V_S) and operates from a 4.5 V to 18 V supply. The MIC4451 inverts its input and is offered alongside the non-inverting MIC4452, both rated for 12 A peak sink/source and an output resistance of 0.8 ohm. A low-side gate driver is a power-management IC that sits between a low-power logic controller (microcontroller, FPGA, gate-driver logic output) and the gate of a high-current MOSFET or IGBT. Its purpose is to translate a weak 3.3 V or 5 V logic signal into a strong, fast 0-12 V gate-drive pulse capable of switching large power transistors in nanoseconds, thereby reducing switching losses and avoiding the shoot-through caused by slow gate transitions. Low-side MOSFET drivers -> gate drivers -> power management ICs -> semiconductor devices is the standard taxonomy for this category. Key features of the MIC4451YN include 12 A peak output drive, a low 0.8 ohm output impedance for fast edges, 4.5 V to 18 V supply operation, and proprietary input circuits that tolerate negative input swings down to -5 V without latch-up damage. Internal ESD protection, thermal shutdown, and latch-up immunity make the part suitable for harsh industrial environments. The bipolar/CMOS/DMOS process achieves high peak current in a small die while keeping quiescent supply current modest. Architecture-wise, the MIC4451YN combines a CMOS input stage with a DMOS push-pull output stage, allowing high peak currents without external boost capacitors or speed-up networks. Typical rise/fall times of 20-40 ns into 1000 pF loads make the driver fast enough to switch most TO-220 and TO-247 power MOSFETs efficiently. The device's wide V_S range also makes it compatible with both 5 V and 12 V logic-level designs and with 12 V/24 V industrial supply rails. Typical applications include switch-mode power supply (SMPS) gate drives, motor-driver half-bridge low-side stages, solenoid and relay drivers, DC-DC converter synchronous-rectifier drives, and pulse transformer drivers. The 12 A peak capability is sufficient to switch the largest discrete MOSFETs in sub-1 kW power stages without external discrete buffer transistors. When designing with this part, place a 1 uF low-ESR bypass capacitor directly across V_S and GND to handle the high di/dt of the output stage, and keep the gate-drive loop area minimal to limit ringing. The inverting topology means the MOSFET is ON when the logic input is LOW - verify this against your control firmware to avoid shoot-through in half-bridge configurations. This page synthesizes distributor pricing, drop-in alternatives, comparison parameters, and practical design notes not found in the manufacturer datasheet alone, giving engineers a single reference for part selection.

RFQ پەیوەندی
MIC4452ZT - 12A Non-Inverting Low-Side MOSFET Driver | Microchip
MIC4452ZT

MIC4452ZT - 12A Non-Inverting Low-Side MOSFET Driver | Microchip

The Microchip Technology MIC4452ZT is a non-inverting, low-side CMOS MOSFET gate driver capable of 12 A peak output from a 4.5 V to 18 V supply. It is packaged in a five-lead TO-220 with tab and is supplied in tube packaging. The device uses a bipolar, CMOS, and DMOS process to provide efficient gate charging for power MOSFETs in demanding switching circuits. A MOSFET gate driver is a specialized power-management IC that converts a low-current logic command into the high peak-current charge and discharge pulses required by a power MOSFET gate. In the broader hierarchy, the MIC4452ZT is a gate driver, then a power MOSFET driver, a power management IC, and a semiconductor. Low-side placement means the driver sits on the same supply side as the MOSFET source referenced to ground. Key verified characteristics include a 12 A peak output, low-side configuration, non-inverting input operation, and approximately 15 ns propagation delay. The manufacturer states that MIC4451 and MIC4452 accept any logic input from 2.4 V up to the supply voltage without external speed-up capacitors or resistor networks. This simplifies control interfaces across different logic-voltage domains. The CMOS output stage can charge and discharge large MOSFET gates rapidly, reducing switching transition time and associated conduction or switching losses. Its 12 A peak capability provides a substantial drive-current margin over the average gate current required during switching. The MIC4452 is the non-inverting member of the family, whereas MIC4451 uses an inverting input configuration. Typical uses include DC motor control, power-converter switching, load drivers, and general high-current MOSFET switching. The TO-220-5 construction also offers a larger thermal path than small surface-mount driver packages, although exact junction-temperature and thermal-resistance limits must be taken from the manufacturer datasheet. Designers should verify absolute maximum voltage, input thresholds, output behavior, and thermal conditions against the official datasheet before production use. Gate resistance, dead time, layout inductance, and the selected MOSFET remain critical to switching performance. The verified material does not provide complete pricing or a complete pin-level mapping, so those details are marked as needed rather than inferred.

RFQ پەیوەندی
MIC5800YM - 50V 4-Bit Latched Driver SOIC-14 | Microchip
MIC5800YM

MIC5800YM - 50V 4-Bit Latched Driver SOIC-14 | Microchip

The Microchip Technology MIC5800YM is a high-voltage, high-current 4-bit parallel-input latched driver integrating four CMOS data latches, bipolar Darlington output stages, and CMOS control logic, packaged in a 14-pin SOIC. It delivers up to 500 mA per channel and supports output voltages up to 50 V, making it a drop-in interface between low-power microcontrollers and inductive, relay, solenoid, or lamp loads. What is a latched driver? A latched driver is a power-management IC that holds the last-written logic state on its outputs until the host writes a new value, freeing the microcontroller from continuous PWM or GPIO refresh. Within the broader hierarchy, latched drivers fall under power management ICs (PMICs) and are commonly classified alongside power distribution switches and load drivers. The MIC5800 sits between the digital control domain (MCU) and the high-power load domain (relay coils, stepper windings, Nixie/LED arrays), providing level shifting, current amplification, and transient protection in a single device. Key specifications include four parallel CMOS-compatible data inputs (D1–D4), common STROBE and CLEAR controls, an OUTPUT ENABLE pin, 50 V minimum output breakdown, and 500 mA continuous sink current per channel. The bipolar Darlington pairs achieve typical VCE(sat) around 1.0 V at low currents, with integral flyback clamping diodes for inductive loads. Each output can be paralleled to increase current capability, and the device operates from a single 5 V logic supply. Architecturally, the MIC5800YM combines CMOS latches with bipolar Darlingtons in a mixed-process BiCMOS design, ensuring low quiescent current on the logic side while the output transistors handle the high-voltage and high-current loads. The latches are edge-triggered by STROBE and asynchronously cleared by CLEAR, allowing deterministic update of all four channels simultaneously with predictable timing. Typical applications include relay and solenoid drivers, stepper motor phase drivers, LED or lamp multiplex displays, print-head driver arrays, and high-side or low-side switching of 12–48 V industrial loads. The MIC5800YM is also widely used in legacy test equipment and telecom line-interface boards where bipolar drive strength is preferred over MOSFET-only switches. When designing with the MIC5800YM, place a 0.1 µF decoupling capacitor close to VDD and respect the 50 V absolute-maximum output rating. The Darlington outputs have a saturation voltage that must be budgeted against load supply headroom, especially when driving low-voltage relays from a 5 V rail. This page synthesizes verified distributor pricing, drop-in alternatives from the same MIC58xx family and competing bipolar latched drivers, and practical design notes that complement the Microchip datasheet.

RFQ پەیوەندی
MIC5842YN - 8-Bit Serial-In Latched Driver, 500mA, 18-DIP | Microchip
MIC5842YN

MIC5842YN - 8-Bit Serial-In Latched Driver, 500mA, 18-DIP | Microchip

The Microchip Technology MIC5842YN is an 8-bit serial-input latched driver fabricated with BiCMOS technology and housed in an 18-pin PDIP (DIP-18) through-hole package. It integrates an 8-bit CMOS shift register, CMOS control logic, and eight CMOS data latches followed by eight bipolar Darlington output stages rated at 500 mA continuous per channel with a 50 V minimum load-voltage rating per output. A latched driver is a type of peripheral power driver IC that accepts serial data from a microcontroller or logic controller, latches it for steady-state retention, and uses high-current bipolar outputs to switch inductive, capacitive, or lamp loads. It sits in the family of power management and load driver ICs (PMIC -> Load Driver -> Serial Latched Driver -> Peripheral Driver), bridging low-power CMOS logic and high-current real-world loads. Key features include a wide 5 V to 15 V supply operating range, output transient capability of 80 V per channel for inductive load turn-off, 500 mA continuous sink current per channel, an active-low STROBE latch-enable input, a serial data output pin for cascading multiple MIC5842 devices, and built-in input pull-up structures. The BiCMOS architecture gives the part its combination of low-power CMOS logic and high-current bipolar drive in a single die. The MIC5842YN is typically used to drive relays, solenoids, lamps, LED arrays, stepper motor windings, and incandescent displays. By clocking data into the shift register one bit at a time and then latching the parallel outputs simultaneously, designers can control up to eight high-current loads using only three or four microcontroller pins. When designing with this part, place a 0.1 uF decoupling capacitor close to VCC (Pin 6) and use flyback diodes on inductive loads or rely on the IC's internal clamp diodes. Output ground returns to GND at Pin 3. Maximum package dissipation must be observed when all eight outputs are fully loaded.

RFQ پەیوەندی
MP5032 - 3A USB Current-Limit Switch with QC 3.0 ID | MPS
MP5032

MP5032 - 3A USB Current-Limit Switch with QC 3.0 ID | MPS

The Monolithic Power Systems MP5032 is a USB power switch with integrated Quick Charge 3.0 charging-port identification, delivering up to 3A of continuous load current from a wide input supply range and housed in a compact TSOT-23-6 (GJ) package. The device combines a programmable current-limit power switch with battery-charging protocol detection for DCP schemes including BC1.2, divider mode, 1.2V/1.2V mode, and Qualcomm Quick Charge 3.0 handshake, all without external user interaction. A USB current-limit switch is a power-management load switch that sits between a DC supply rail (typically 5V or a higher adapter voltage) and a USB VBUS output. It enforces a programmable current limit, protects upstream components from over-current events, and increasingly includes protocol handshaking that allows the downstream port to advertise the voltages and currents it can deliver. The MP5032 belongs to the broader USB power delivery (USB-PD) and proprietary fast-charging IC family, sitting below full USB-PD controllers in complexity but supporting the most common legacy and QC3.0 handshake schemes used by smartphone and tablet charging adapters. Key features include a hiccup current-limit architecture, line-drop compensation that maintains accurate USB cable-delivered voltage, input over-voltage protection (OVP), thermal shutdown, and an active-high enable input. The integrated current-limit and ID functions let the designer replace a discrete load switch plus external USB-IF detection chip with a single IC. Internally, the part uses a low-RDS(ON) N-channel MOSFET pass element, a precision current-sense amplifier, and a state machine that decodes BC1.2, divider-mode, and QC3.0 voltage requests on the D+/D- lines. The hiccup behavior auto-recovers from sustained over-current faults without latching the system off, which is important for hot-plug USB events. Typical applications include USB wall chargers, travel adapters, automotive USB power ports, USB hub downstream ports, and any 5V (or higher adapter) rail that must support Quick Charge 3.0 handsets or legacy DCP phones. The wide input range also supports 12V automotive environments after upstream regulation. When designing with this device, follow MPS layout guidance: place the input capacitor immediately adjacent to IN, keep the current-limit set resistor close to ILIM, and ensure the exposed thermal pad (when present) sees a generous copper pour. Verify QC3.0 conformance with the latest Qualcomm compliance checklist. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes that go beyond the brief block-diagram information in the manufacturer datasheet.

RFQ پەیوەندی