Video ICs
بەرهەمەکان (78)
TPS65197BRUYR - 8-Channel LCD Level Shifter | Texas Instruments
Texas Instruments TPS65197BRUYR is an 8-channel LCD level-shifter IC with no, 2-channel, or 3-channel charge-sharing support and panel discharge to VGH during shutdown, packaged in a 28-pin WQFN (RUY) package. It is designed to manage the high-voltage and low-voltage signaling requirements encountered in LCD-panel gate-drive systems while reducing the number of discrete switching and level-translation functions on the board. An LCD level shifter is a specialized interface IC that translates gate-driver signals to the voltage domain required by an LCD panel. In the broader electronics hierarchy, this device is a display interface and voltage-level translator within interface ICs and semiconductor power-management-adjacent signal conditioning. The TPS65197 combines eight signal channels, configurable charge sharing, and shutdown panel discharge to support TFT-LCD panel timing and gate-drive architectures. The verified feature set centers on 8 independently addressed level-shifter channels, support for no, 2-channel, and 3-channel charge-sharing modes, and discharge of the panel to VGH when the device enters shutdown. These functions address the practical need to control gate-line transitions, reduce transition-load demand, and establish a defined off state for TFT-LCD panels. The 28-pin WQFN (RUY) package also supports compact display-controller designs where connector count and routing area are constrained. The RUY package is a 4 mm by 4 mm WQFN outline with 28 pins and a thermal pad, combining a small footprint with direct PCB heat-spreading capability. Its exposed pad provides a thermal path to the board copper rather than relying only on package leads. Although this is principally a signal-interface device rather than a power semiconductor, the exposed pad must still be connected according to the manufacturer land pattern and thermal guidance to preserve electrical performance, assembly yield, and temperature reliability. TPS65197BRUYR is appropriate for TFT-LCD monitor panels, industrial HMIs, small-format embedded displays, test equipment, and other systems requiring coordinated level translation, charge sharing, and controlled panel shutdown. Designers should match the panel's gate-line count, allowable charge-sharing mode, VGH operating behavior, signal timing, and shutdown requirements before finalizing a system design. The use of supported charge-sharing modes can lower effective switching load, while panel discharge provides a defined shutdown sequence. PCB layout should keep the level-shifter outputs and VGH-related connections short, preserve the manufacturer's recommended copper and thermal-pad geometry, and maintain clean return paths beneath the device. Designers must also validate output timing against the target panel because no, 2-channel, and 3-channel operation are not interchangeable for every controller. Power sequencing should be coordinated with the display controller so VGH is not removed before the required panel-discharge interval has completed. This page consolidates the verified TI product information, distributor availability, package details, pricing snapshot, selection guidance, and design considerations for TPS65197BRUYR. It also separates confirmed technical facts from parameters that require confirmation in the manufacturer datasheet, helping engineers evaluate panel compatibility without relying on assumptions.
TPS65197BRUYT - 8-Channel LCD Level Shifter | Texas Instruments
The Texas Instruments TPS65197BRUYT is an eight-channel level-shifter IC for LCD display applications, supplied in a 28-pin WQFN (RUY) package measuring 4 mm by 4 mm. It converts timing-controller logic-level signals into the higher gate-in-panel voltage levels required by LCD panels. The device supports two-channel and three-channel charge sharing, panel discharge to VGH during shutdown, and operation from a 16.5 V to 45 V supply range. Its specified operating temperature range is -40 °C to 85 °C. An LCD level shifter is a voltage-interface IC used between a display timing controller and the high-voltage gate-driver inputs of an LCD panel. Within the signal-chain hierarchy, it belongs to interface ICs and video ICs rather than a display driver or low-voltage digital logic device. Its principal purpose is to translate low-voltage timing signals while coordinating charge sharing and panel discharge, helping the display system reach a defined state during power transitions. The TPS65197 provides eight level-shifting channels together with clock outputs that support normal operation, two-channel charge sharing, and three-channel charge sharing. The manufacturer describes it as an eight-channel device intended for notebook, monitor, and television LCD panels. Charge-sharing support reduces the number of high-voltage gate-driver components required in suitable panel architectures, while the panel-discharge function provides a controlled path to VGH during shutdown. The 16.5 V minimum and 45 V maximum supply specification places the device in the high-voltage interface category used by LCD gate-driver systems. The exact channel-level voltage ranges, output-current limits, timing values, and enable or mode details were not present in the supplied verified excerpts and therefore must be checked against the complete manufacturer datasheet before layout or design release. Typical uses include notebook LCD panels, desktop monitors, television panels, and other display systems that translate timing-controller outputs into GIP gate-drive signals. Designers should pay particular attention to charge-sharing mode selection, shutdown sequencing, VGH discharge behavior, exposed-pad thermal management, and the recommended input and output timing layout. The 28-pin 4 mm by 4 mm WQFN package supports compact display-controller boards, but its fine pitch and exposed pad require disciplined PCB layout. Confirm the exact RUY land pattern, thermal-pad connection, voltage rails, and timing constraints using the current TI datasheet and application information before production. This page consolidates verified manufacturer and distributor information with package details, procurement data, display-use guidance, and explicit identification of specifications that still require confirmation. It distinguishes verified facts from missing technical parameters so engineers can assess suitability without relying on unverified assumptions.
TUSB2E22 - eUSB2 to USB 2.0 Dual Repeater | Texas Instruments
The Texas Instruments TUSB2E22 is a USB-compliant eUSB2-to-USB 2.0 dual repeater (redriver) that bridges low-voltage eUSB2 interfaces on modern processors to standard USB 2.0 ports. It supports low-speed (LS), full-speed (FS), and high-speed (HS) signaling at up to 480 Mbps and is available in a 25-pin DSBGA (2x2 mm) package, with a 20-pin VQFN-FCRLF (3.5x3.5 mm) option in the family (TUSB2E22RZA). An eUSB2 repeater is a signal conditioning IC in the USB interface IC (redriver/repeater) family that converts between the 1.2 V single-ended eUSB2 signaling used by advanced low-voltage SoCs and standard 3.3 V-signaling USB 2.0 ports. It sits in the signal chain between the SoC eUSB2 PHY (eDSPr or eUSPr) and the external USB connector, regenerating signals to maintain USB 2.0 compliance. This device category is a critical enabler as process nodes shrink and I/O voltages fall below legacy USB levels. Key features include compliance to USB 2.0 and eUSB2 (rev 1.1), support for LS/FS/HS signaling, a dual repeater with a 2:2 crossbar mux, and host-and-device mode (DRD) support, allowing each repeater to be independently configured. Four eUSB2 compensation settings via the EQ0 and EQ1 pins let designers optimize output compensation for different channel-loss profiles, trace lengths, and connector losses. Architecturally, the TUSB2E22 retimes and re-drives USB signals, improving signal integrity over long traces and through connectors. The 2:2 crossbar mux supports flexible routing, including USB Type-C receptacle flipping where the D+/D- pair swaps between A6/A7 and B6/B7 positions. Power is supplied from VDD3V3 and VDD1V8 rails with no power-up sequence requirement between them; RESETB (active low) can also act as a power-down pin. Typical applications include USB Type-C ports on laptops and desktops, docking stations, USB hubs, and embedded systems whose SoCs expose only eUSB2. It is especially valuable where processor I/O voltage is too low for direct USB 2.0 signaling. Design consideration: configure EQ0/EQ1 per your PCB trace length and connector loss, decouple both supply rails well, and ensure VDD3V3/VDD1V8 ramp within 2 ms per the datasheet power-up recommendation. Prices as of 2026-08-30.
TVP5146M2PFPR - 10-bit NTSC/PAL/SECAM Video Decoder | TI
The Texas Instruments TVP5146M2PFPR is a high-quality 10-bit single-chip digital video decoder that digitizes and decodes NTSC/PAL/SECAM composite and S-Video into digital component YCbCr, housed in an 80-pin HTQFP (PFP) package measuring 12x12 mm with an operating temperature range of 0 to 70 C. A digital video decoder is an analog front-end (AFE) IC that converts baseband analog video signals into digital component video suitable for processing by SoCs, DSPs, and FPGAs. Within the signal-chain hierarchy, it sits below video ADCs in abstraction: it integrates multiple high-speed ADCs (four 11-bit converters in this family), clock generation, synchronization separation, and color-space conversion on one die, making it a complete analog-video-to-digital-bridging solution for embedded video systems. Key features include 4x10-bit digital video output, A/D conversion of component RGB and YPbPr signals, an integrated 5-line adaptive comb filter that suppresses cross-luminance and cross-color artifacts in composite decoding, and Macrovision detection for copy-protection compliance. SCART support enables European consumer platform designs, and automatic standard detection of NTSC, PAL, and SECAM simplifies software bring-up. Architecturally, the TVP5146M2 digitizes the selected analog input through its embedded 11-bit ADC stage, applies analog clamping and gain control, then performs digital multi-standard decoding with the 5-line comb filter. YCbCr output is delivered over a standard parallel digital video port that interfaces directly to common video processors and display controllers. Linear-phase horizontal and vertical scaling-free output timing keeps downstream pipeline design straightforward. Typical applications include CCTV and DVR front ends, LCD monitors and TVs, video capture cards, set-top boxes, and industrial machine-vision equipment that must accept legacy composite, S-Video, YPbPr, or RGB sources. Design consideration: place a low-jitter crystal or clock source per the manufacturer datasheet layout guidance and keep analog inputs routed over a solid ground plane, since decoder SNR depends strongly on input clock jitter and analog layout quality. This page synthesizes distributor pricing, drop-in alternatives, comparison data, and practical design notes not found in the manufacturer datasheet alone.
TVP5151PBSR - NTSC/PAL/SECAM Video Decoder | TI | 32-TQFP
The Texas Instruments TVP5151PBSR is an ultralow-power NTSC/PAL/SECAM video decoder that converts analog composite video signals into 8-bit ITU-R BT.656 digital video with embedded syncs, housed in a 32-pin TQFP (PBS) 5x5 mm package operating from 0C to +70C. A video decoder is a mixed-signal interface IC that sits at the front end of a video capture system, digitizing analog composite (CVBS) or S-Video signals so that a host processor, DSP, or video encoder can process them. Within the signal-chain hierarchy, it belongs to the video decoder family of interface ICs, bridging the analog broadcast world and the digital video processing domain. Key features include programmable output formats - 8-bit 4:2:2 with embedded syncs (ITU-R BT.656) or 8-bit 4:2:2 with discrete syncs - Macrovision copy protection detection, and complementary four-line adaptive comb filtering for both luminance and chrominance paths to reduce cross-luminance and cross-chrominance artifacts. A chrominance trap filter is also available as an alternative to comb filtering. The optimized architecture achieves ultralow power consumption, making the device especially suitable for battery-powered systems. A Genlock/real-time control (RTC) output is generated for synchronizing downstream video encoders, which simplifies the design of capture-and-display pipelines. Analog supply operates from 1.65V to 1.95V, and an I2C serial interface programs all decoder functions including input selection, contrast, brightness, saturation, and hue. Typical applications include cell phones and PDAs with video-in capability, portable media players and recorders, security/surveillance capture front ends, and set-top-box analog input ports. The 5x5 mm TQFP footprint suits space-constrained portable designs. Design consideration: the ultralow-power supply rails are tight (1.65V-1.95V analog core); plan a clean 1.8V LDO rail and follow the datasheet decoupling recommendations to preserve decoder signal-to-noise performance on the analog inputs. This page synthesizes distributor pricing, drop-in alternative data, and practical design notes not found in the manufacturer datasheet.
VSC8502XML - Dual-Port GbE Copper PHY QFN-135 | Microchip
The Microchip Technology VSC8502XML is a dual-port 10/100/1000BASE-T Ethernet physical layer transceiver (PHY) with integrated line-side termination, housed in a 135-pin QFN (12x12 mm) package. It supports 1 Gbps data rates over copper with (G/RG)MII host interfaces. An Ethernet PHY (physical layer transceiver) is the IC that connects a media access controller (MAC) to the physical copper or fiber medium. Sitting at the bottom of the networking IC hierarchy - Ethernet controller, MAC, PHY, magnetics, jack - the PHY performs analog line drivers and receivers, clock and data recovery, auto-negotiation, and 10/100/1000BASE-T encoding. The VSC8502 belongs to the copper PHY category of Ethernet interface ICs used in switching, routing, and embedded connectivity designs. Key features include integrated line-side terminations, which eliminate up to 16 external precision resistors per port, conserve board space, reduce EMI, and improve system performance. Microchip further reduces bill-of-materials complexity and component count through integrated support circuitry. Dual integrated ports in one 12x12 mm package cut PHY count versus two single-port PHYs such as the KSZ9131, saving layout area and cost. Architecturally, the VSC8502 integrates two independent gigabit copper PHY cores sharing a common digital host interface supporting (G/RG)MII modes, enabling connection to 16-bit or 32-bit MACs, switch fabrics, or processors. Energy-efficient Ethernet and low-power modes reduce system power during idle link periods, an important consideration for multiport industrial and enterprise equipment. Typical applications include space-constrained 10/100/1000BASE-T designs: industrial Ethernet nodes and gateways, embedded switch and router line cards, IP surveillance cameras, networked test instruments, and server management (BMC) ports requiring dual copper links in a compact footprint. A key design consideration is preserving the PHY-to-magnetics routing: with line-side termination integrated, keep the board trace between the QFN package and the transformer short and impedance-controlled at 100 ohms differential, and follow Microchip layout guidance for ground referencing. This page adds value beyond the manufacturer datasheet by consolidating distributor availability, drop-in alternatives, application guidance, and practical design notes in one place for sourcing and design engineers.