AD517SH - 75uV Precision Offset Op Amp | Analog Devices
MPN: AD517SH ✓ چالاکAD517SH گشتی
An operational amplifier is a voltage-feedback differential amplifier that uses high open-loop gain to amplify the difference between its non-inverting and inverting inputs. Negative feedback creates a closed-loop gain determined mainly by external resistors. Within the amplifier hierarchy, the AD517SH belongs to the precision operational-amplifier category and ultimately the broader integrated-circuit and analog-signal-processing families. The AD517SH is intended for instrumentation and measurement circuits where offset error is important relative to the measured signal.
The AD517SH combines laser trimming with a thermally balanced monolithic layout and precision IC processing. These features are intended to reduce input offset voltage and improve repeatability between individual devices. Its 0.25 MHz gain-bandwidth product is modest compared with modern high-speed amplifiers, but that bandwidth supports low-frequency precision tasks without requiring the higher power and noise associated with wideband amplifiers. The hermetic TO-99-8 metal-can enclosure also provides a durable option for legacy industrial and instrumentation platforms.
Typical uses include low-level sensor amplification, strain-gauge and bridge excitation signal paths, precision buffering, laboratory measurement equipment, and analog instrumentation. In these circuits, the AD517SH serves as a gain stage or buffer rather than a high-speed signal-path device. The design should preserve the amplifier's common-mode operating range, input bias-current behavior, supply requirements, and stability requirements at the selected closed-loop gain.
For a new design, check the manufacturer datasheet for the complete electrical characteristics, environmental ratings, pin assignment, and recommended compensation values. Keep sensitive input and feedback routing short, place input-biasing resistors close to the appropriate pins, and provide stable local bypassing at the power terminals. Prototype the selected gain configuration because input capacitance, source impedance, and load capacitance can affect closed-loop stability.
This product page combines the AD517SH's published device identity, package information, and precision characteristics with practical application guidance, sourcing information, and a conservative replacement analysis. It is intended to help engineers determine whether this traditional monolithic operational amplifier matches the accuracy, bandwidth, environmental, and mechanical requirements of an existing design.
جێگرەوەکانی جێگۆڕکێ بۆ AD517SH — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ AD517SH (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Product Type, Input Transistor Type.
هیچ جێگرەوەی ڕاستەوخۆ بۆ ئەم بەرهەمە بەردەست نییە.
داوای جێگرەوەکان بکەAD517SH زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان
| Product Type | Precision operational amplifier |
| Manufacturer | Analog Devices |
| Maximum Input Offset Voltage | 75 uV |
| Gain-Bandwidth Product | 0.25 MHz |
| Number of Circuits | 1 circuit |
| Amplifier Type | General-purpose precision amplifier |
| Offset Adjustment Method | Laser trimmed |
| Construction | Monolithic |
| پاکێج | TO-99-8 metal can |
| Package Pin Count | 8 pins |
| Package Type | Hermetically sealed metal can |
| جۆری دامەزراندن | Through-hole |
ڕێنمایی ڕێکخستنی پینی AD517SH hermetically sealed metal can
ڕێکخستنی پین بۆ AD517SH (پاکێجی hermetically sealed metal can). ئەم پێکھاتە ئەنالۆگە پینی چوونەژوورەوە، دەرچوون و دابینکردنی وزەی ھەیە. سەرنج بدە بە داتاشیتی بەرھەمھێنەر بۆ ڕێکخستنەکانی پینی لادانی ئۆفسێت، قەرەبووکردنەوە و چالاککردن. گونجاوە بۆ ڕێکخستنی ئیشارەت و خولەکانی بەرزکەرەوە.
هیچ داتای وردی پینئاوت بەردەست نییە بۆ AD517SH.
سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.
بەکارهێنانە باوەکان
AD517SH گونجاوە بۆ 6 بەکارھێنانs: Strain-Gauge Bridge Instrumentation, Precision Sensor Signal Conditioning, Laboratory Buffer and Gain Stage, Industrial Process-Control Analog Front End, Legacy Instrumentation Retrofit, Precision Signal Buffering.
Strain-Gauge Bridge Instrumentation
The AD517SH fits low-level strain-gauge instrumentation because its laser-trimmed input offset is specified at no more than 75 uV. Place the amplifier in a differential gain stage when the bridge output contains millivolt-level signals; the input offset contribution scales with the closed-loop noise gain and can otherwise dominate the measurement. Its 0.25 MHz gain-bandwidth product is suitable for temperature, force, and vibration measurements that change relatively slowly. Keep input leads short, use matched high-value resistors, and follow the manufacturer's grounding and nulling guidance to avoid converting offset error into a significant fraction of the measured strain.
Precision Sensor Signal Conditioning
The AD517SH can amplify low-amplitude outputs from resistive, thermocouple, and pressure sensors when the required bandwidth is below its 0.25 MHz gain-bandwidth product. The 75 uV maximum offset specification is valuable when the sensor signal is only slightly larger than the amplifier's error contribution, while the extremely low input currents help preserve high-impedance sensor signals. Define the closed-loop gain before choosing resistor values, check that the sensor common-mode voltage remains inside the amplifier's permitted range, and use a low-noise reference and stable supply for the best achievable measurement resolution.
Laboratory Buffer and Gain Stage
The AD517SH is appropriate for buffering and gain stages in slower laboratory instruments where measurement accuracy depends more on input offset than on wide bandwidth. Its 0.25 MHz gain-bandwidth product supports signals well below that limit, and the 75 uV maximum offset limits the input-referred error introduced at high closed-loop gain. Use the device as a unity-gain buffer when source impedance is high, or establish a stable resistor-defined gain with local feedback routing. Verify output-drive and load-capacitance limits from the datasheet before driving long cables or unusual test fixtures.
Industrial Process-Control Analog Front End
The AD517SH can serve as the precision gain stage for slow industrial process signals such as pressure, level, and position measurements. The single-circuit monolithic design, 75 uV maximum input offset, and 0.25 MHz bandwidth align with control systems that condition low-level analog inputs before digitization or conversion to a higher-level voltage. Keep the amplifier away from switching-power inductors and high-current traces, bypass its supply pins locally, and account for input common-mode limits. If the sensor is exposed to long cable runs or high transients, add suitable input protection without degrading source impedance or bias-current balance.
Legacy Instrumentation Retrofit
The AD517SH is particularly useful when repairing or extending an existing TO-99-8 instrumentation design because it preserves the through-hole form factor and traditional precision-op-amp architecture. Its 75 uV maximum offset and 0.25 MHz gain-bandwidth product target low-frequency analog measurement functions that commonly appear in older laboratory and industrial equipment. Before replacing an existing device, compare the complete pinout, offset-null implementation, supply voltage, input bias current, and compensation requirements. Inspect the socket or PCB for contamination and mechanical stress, since connector or socket problems can imitate amplifier failure.
Precision Signal Buffering
The AD517SH can buffer a high-impedance source into a downstream measurement or conversion stage when the signal bandwidth remains below 0.25 MHz. Its low-offset, low-input-current architecture helps avoid loading the source, while the hermetically sealed TO-99-8 package provides a mechanically rugged through-hole option for fixed equipment. Confirm the source impedance and capacitance against the amplifier's input characteristics, route the input as a short guarded trace, and maintain stable feedback connections. For long or high-capacitance loads, verify stability with the manufacturer's recommended compensation values rather than relying on general op-amp rules.
داتای سەرچاوەی ئەندازیاری بۆ AD517SH — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە |
|---|---|
| Package | TO-99-8 hermetically sealed metal can |
| Brand | Analog Devices |
| Maximum Input Offset Voltage | 75 uV |
| Gain-Bandwidth Product | 0.25 MHz |
| Number of Circuits | 1 circuit |
| Amplifier Type | General-purpose precision amplifier |
| Offset Adjustment Method | Laser trimmed |
| Mounting Type | Through-hole |
| Construction | Monolithic |
| Lifecycle Status | Active |
جیاکەرەوە سەرەکییەکان
- Precision offset specification (بەراورد بەAD515AKH)
- Established low-frequency precision bandwidth (بەراورد بەAD518SH/883B)
- Legacy-compatible through-hole construction (بەراورد بەAD517A)
تێبینییەکانی دیزاین
Do not select a TO-99 amplifier solely by package outline. Verify the exact pin functions, offset-null connection, supply terminals, and input-output assignments in the Analog Devices pinout before constructing a replacement board. A mechanically similar amplifier can still differ electrically or functionally. When adapting an existing circuit, also compare the required supply voltage, common-mode input range, bias-current behavior, and compensation method rather than assuming that the 75 uV offset specification alone establishes interchangeability.
Keep the amplifier input, feedback components, and output as compact and direct as practical, especially when the AD517SH handles high-impedance sensor sources. Route input traces away from switching nodes and digital return currents, and place the offset-null equipment or trim network only as directed by the manufacturer. For long sensor cables, add protection at the connector while preserving the intended input impedance and balance. These layout measures matter because parasitic capacitance and leakage can degrade stability or convert into additional error at the very low signal levels supported by a precision amplifier.
Decouple the power terminals locally and verify the supply voltage against the operating limits in the Analog Devices datasheet before energizing the circuit. Use a stable, low-noise supply because power-supply variation can create error that appears at the output of a high-gain precision stage. Check output-current demand, output swing, and load limitations at the selected supply voltage. Do not infer safe operation from the offset and bandwidth figures alone; those parameters do not establish the device's complete electrical operating envelope.
زانیاری پابەندبوون
The AD517SH is a legacy hermetically sealed TO-99-8 precision operational amplifier. Current RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals status must be confirmed for the exact orderable MPN and manufacturing lot.