AD526ADZ - 16x Programmable Gain Amplifier | Analog Devices
MPN: AD526ADZ ✓ چالاکAD526ADZ گشتی
A software-programmable gain amplifier, or SPGA, is a specialized analog signal-conditioning IC that changes its voltage gain through digital control signals. It belongs to the amplifier hierarchy, where an SPGA is more specialized than a fixed-gain operational amplifier and provides a controlled way to normalize signals that arrive over a wide amplitude range. Common system-level roles include sensor-interface amplification, data-converter front ends, laboratory instrumentation, and programmable test and measurement paths.
The AD526ADZ provides five binary-programmable gain choices, allowing a system to select sensitivity according to the measured signal level. Gain selection is implemented with latched TTL-compatible control inputs, making the part suitable for processor- or microcontroller-controlled analog front ends. Its single-channel architecture is appropriate when one analog signal must be conditioned at a time, while its monolithic construction eliminates the need for an external switched-resistor network and associated layout complexity.
The AD526ADZ has a bandwidth of 350 kHz and supports bipolar supplies from ±4.5 V through ±16 V. These characteristics make it relevant to instrumentation requiring adjustable amplification but not the bandwidth of a high-speed voltage-feedback amplifier. The -55°C to +125°C temperature range also supports industrial and temperature-tolerant signal-chain designs, subject to the complete operating conditions and electrical limits in the manufacturer datasheet.
Typical uses include bridge-transducer signal conditioning, programmable audio and communications paths, laboratory measurement front ends, and analog data-acquisition systems. In a data-converter interface, the programmed gain can bring a changing sensor output into a more useful range before conversion. In instrumentation, the five fixed gain selections simplify calibration while avoiding a general-purpose relay or analog switch in the feedback path.
Designers should route the latched control signals away from sensitive analog inputs and use a quiet ground and supply arrangement. Because an SPGA contains both analog and digital-control functions, PCB partitioning, input filtering, and supply bypassing influence usable signal-to-noise performance. The pin-description table in the manufacturer datasheet should be used when assigning the 16 package connections and planning the board layout.
This page organizes the AD526ADZ specifications, application guidance, package information, and verified drop-in alternatives. It also highlights where the monolithic SPGA simplifies implementation and where bandwidth, supply voltage, and control requirements should be checked before replacing it in an existing instrumentation design.
جێگرەوەکانی جێگۆڕکێ بۆ AD526ADZ — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ AD526ADZ (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Package.
AD526AD
✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوەپەیوەندی بۆ نرخ
بینینی داتاشیت →AD526BD
✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوەپەیوەندی بۆ نرخ
بینینی داتاشیت →AD526ADZ زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان
| Product Type | Single-ended monolithic software-programmable gain amplifier |
| Number of Circuits | 1 circuit |
| Available Gain Values | 1, 2, 4, 8, and 16 |
| Bandwidth | 350 kHz |
| Supply Voltage Range | ±4.5 V to ±16 V |
| Minimum Supply Voltage | ±4.5 V |
| Maximum Supply Voltage | ±16 V |
| مەودای پلەی گەرمیی کارکردن | -55°C to +125°C |
| Input Type | Single-ended |
| Control Interface | TTL-compatible latched inputs |
| Integrated Functions | Amplifier and resistor network |
| External Components Required | None |
| پاکێج | 16-lead ceramic DIP (16-CDIP) |
| ژمارەی پین | 16 pins |
| جۆری دامەزراندن | Through-hole |
| دۆخی RoHS | unknown |
| REACH Status | unknown |
| AEC-Q100 Qualification | not_applicable |
| Lead-Free Status | unknown |
| Halogen-Free Status | unknown |
ڕێنمایی ڕێکخستنی پینی AD526ADZ 16-lead ceramic dip (16-cdip)
ڕێکخستنی پین بۆ AD526ADZ (پاکێجی 16-lead ceramic dip (16-cdip)). ئەم پێکھاتە ئەنالۆگە پینی چوونەژوورەوە، دەرچوون و دابینکردنی وزەی ھەیە. سەرنج بدە بە داتاشیتی بەرھەمھێنەر بۆ ڕێکخستنەکانی پینی لادانی ئۆفسێت، قەرەبووکردنەوە و چالاککردن. گونجاوە بۆ ڕێکخستنی ئیشارەت و خولەکانی بەرزکەرەوە.
هیچ داتای وردی پینئاوت بەردەست نییە بۆ AD526ADZ.
سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.
بەکارهێنانە باوەکان
AD526ADZ گونجاوە بۆ 6 بەکارھێنانs: Sensor Signal Conditioning, Data-Acquisition Front End, Laboratory Instrumentation, Programmable Audio Conditioning, Automated Test Systems, Industrial Analog Control.
Sensor Signal Conditioning
The AD526ADZ fits sensor front ends whose output level changes substantially across the measurement range. Its five programmable gains of 1, 2, 4, 8, and 16 let a controller increase amplification for weak readings and reduce it for large signals, keeping the conditioned output within a useful range for the following converter. With 350 kHz bandwidth and ±4.5 V to ±16 V supplies, it is appropriate for moderate-bandwidth sensors rather than high-speed waveform capture. The monolithic resistor network also removes the external switched-resistor network and calibration components normally associated with a programmable gain stage.
پێشنیارکراو
Data-Acquisition Front End
The AD526ADZ can normalize an analog input before it reaches a data-acquisition or mixed-signal converter. The controller selects one of five gains to accommodate different input amplitudes while retaining a 350 kHz bandwidth ceiling. TTL-compatible latched inputs make the gain setting convenient for digital control, although the control traces should remain away from the sensitive analog input path. Operation from ±4.5 V to ±16 V supports instrumentation systems using bipolar rails, while the integrated amplifier and resistor network simplify the analog board layout.
پێشنیارکراو
Laboratory Instrumentation
Laboratory instruments often need selectable gain while keeping signal paths compact. The AD526ADZ provides gains from 1 through 16 through latched TTL-compatible control, allowing a microcontroller to adapt the front end to different probe levels. Its 350 kHz bandwidth supports low-frequency and audio-band measurement functions but not wideband oscilloscope channels. The 16-lead ceramic DIP package is well suited to through-hole laboratory electronics, and the monolithic construction avoids the component count and layout complexity of a discrete switched-resistor amplifier.
پێشنیارکراو
Programmable Audio Conditioning
The AD526ADZ is suitable for audio and communications paths that require digitally selected attenuation or amplification without mechanical switches. Gains of 1, 2, 4, 8, and 16 provide coarse range control, and the 350 kHz bandwidth exceeds the audible band while remaining suitable for many voice-band communication signals. The latched control inputs let the host processor establish the gain before processing a frame. Its ±4.5 V to ±16 V supply capability allows use in bipolar analog systems, though output swing and distortion limits must be checked for the selected operating point.
پێشنیارکراو
Automated Test Systems
Automated test equipment can use the AD526ADZ to select sensitivity according to the fixture or device under test. A controller-driven gain setting from 1 to 16 reduces the need for manual attenuators and simplifies repeatable test sequencing. The 350 kHz bandwidth accommodates many low-frequency electrical measurements and signal-conditioning tasks, while the monolithic SPGA implementation limits external parts. Because the control inputs are latched and TTL-compatible, the gain can be held stable during each measurement interval, improving repeatability when the control system updates the setting only between tests.
پێشنیارکراو
Industrial Analog Control
The AD526ADZ can condition slowly varying or low-frequency industrial process signals when the controller needs selectable amplification. Its -55°C to +125°C operating range is useful across demanding temperature environments, while the broad ±4.5 V to ±16 V supply span supports industrial analog rails with suitable headroom. The single-ended architecture is appropriate for grounded sensor outputs. Programmable gain helps normalize different plant outputs before telemetry or threshold processing, but grounding, bypassing, and isolation must be designed around the system’s noise and safety requirements.
پێشنیارکراو
کورتەی بەرهەمە پێشنیارکراوەکان
داتای سەرچاوەی ئەندازیاری بۆ AD526ADZ — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | AD526AD | AD526BD |
|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices |
| Package | 16-CDIP | 16-pin through-hole package; exact suffix must be verified | 16-CDIP family package; exact suffix must be verified |
| Product Type | Single-ended monolithic SPGA | Single-ended monolithic SPGA | Single-ended monolithic SPGA |
| Available Gain Values | 1, 2, 4, 8, and 16 | 1, 2, 4, 8, and 16 | 1, 2, 4, 8, and 16 |
| Control Interface | TTL-compatible latched inputs | TTL-compatible latched inputs | TTL-compatible latched inputs |
| External Components | None required | None required | None required |
| Number of Channels | 1 circuit | 1 circuit | 1 circuit |
جیاکەرەوە سەرەکییەکان
- Five integrated gain selections without external gain components (بەراورد بەAD526AD)
- Programmable gain with a documented 350 kHz bandwidth (بەراورد بەAD526BD)
- Exact ceramic-DIP ordering configuration (بەراورد بەAD526AD)
تێبینییەکانی دیزاین
Separate the analog input and gain-control paths on the PCB. Route the TTL-compatible latched control signals away from the input pin and sensitive output circuitry to reduce capacitive coupling. Keep the ground return associated with the input and output connections short, and use the pin-description table in the manufacturer datasheet when planning the 16-CDIP footprint and signal flow.
Place local supply bypassing close to the device’s power pins and provide return paths that minimize loop area. The AD526ADZ accepts bipolar supplies from ±4.5 V to ±16 V, but usable signal swing still depends on the actual rail voltages and load. Check the output-current, input-voltage, and output-voltage limits in the manufacturer datasheet before selecting bypass capacitance or supply regulators.
Do not treat every AD526 family member as automatically interchangeable. Verify the exact package suffix, temperature grade, gain accuracy, control timing, and electrical limits for AD526AD or AD526BD before replacing AD526ADZ. Also avoid changing the programmed gain while a sensitive transient is present unless the circuit’s timing and settling requirements have been checked for the selected gain step.
زانیاری پابەندبوون
The AD526ADZ is an analog instrumentation amplifier, so AEC-Q100 automotive qualification is not applicable. No definitive RoHS, REACH, lead-free, halogen-free, or conflict-minerals statement was identified in the product sources used for this page.