Analog Devices

AD694JN - 4-20mA Current Transmitter | Analog Devices

MPN: AD694JN ✓ چالاک
Programmable 10.000 V Vdss 16-pin PDIP Package
MOQ: 1 |

AD694JN گشتی

Analog Devices AD694JN is a monolithic current transmitter that accepts high-level input signals and drives a standard 4-20 mA current loop for process-control equipment. The device also supports a 0-20 mA output range, accepts single- or dual-supply operation, and is packaged in a 16-pin PDIP for through-hole industrial instrumentation.

A current transmitter is a process-control interface that converts a voltage or current-mode input into the standardized 4-20 mA signal used by valves, actuators, transmitters, and remote sensors. Its place in the signal chain is between a sensor or controller and an industrial field loop. This interface category provides a robust way to transfer measurement information over long cables while limiting signal corruption and allowing one measurement input to be monitored remotely.

The AD694JN includes a precalibrated 10 V input range, a programmable 10.000 V precision voltage reference, an input buffer amplifier, and open-loop alarm functionality. According to the Analog Devices AD694 datasheet, the buffered input can scale the incoming signal or buffer the output of a current-mode DAC. These features make the device useful when the source is a high-level process signal or a current-mode converter requiring additional drive capability.

Operation from a single or dual supply gives the designer flexibility when constructing isolated or non-isolated measurement systems. The manufacturer specifies a wide power-supply range extending to +36 V and includes a wide output-compliance capability. These characteristics are especially relevant to industrial systems where loop power may be provided remotely and the transmitter must maintain useful output current across the required load resistance.

Typical uses include 4-20 mA process transmitters, programmable controllers, industrial sensor interfaces, current-mode DAC output buffers, data-acquisition systems, and control loops for valves or actuators. The AD694JN is also suited to laboratory and test equipment requiring a standard analog current output rather than a voltage-only measurement interface.

Designers should verify the selected supply configuration, input range, feedback-network values, output-compliance voltage, and loop load against the Analog Devices AD694 datasheet before releasing a PCB. Because this is a 16-pin PDIP package, adequate through-hole spacing and copper routing for power and current-loop currents are required. Do not add filtering or protection components to the loop without checking their effect on output accuracy and compliance.

This product page consolidates the manufacturer's device description, package information, application context, engineering cautions, and verified replacement status. It is intended to accelerate component identification and board-level planning while keeping every claimed electrical value traceable to the AD694 documentation.

جێگرەوەکانی جێگۆڕکێ بۆ AD694JN — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.

AD694JNZ

✅ جێگرەوەی ڕاستەوخۆ
📦 16-pin plastic DIP
Same 16-pin plastic DIP footprint with a 0-pin-count difference; ordering suffix and qualification details must be confirmed against the manufacturer datasheet.

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

AD694JN زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان

Product Type Monolithic current transmitter
Primary Output Range 4-20 mA
Additional Output Range 0-20 mA
Precalibrated Input Range 10 V
Precision Voltage Reference Programmable 10.000 V
Maximum Supply Voltage +36 V
Supply Configuration Single or dual supply
Input Buffer Amplifier Included
Open-Loop Alarm Supported
پاکێج 16-pin PDIP
Package Type Through-hole PDIP

ڕێنمایی ڕێکخستنی پینی AD694JN through-hole pdip

ڕێکخستنی پین بۆ AD694JN (پاکێجی through-hole pdip). ئەم ئامێرە وزەییە تەرمیناڵی گەیت، درەین و سەرچاوەی ھەیە. بۆ پاکێجە ناڕێکخراوەکان، سەرنج بدە بە داتاشیتی بەرھەمھێنەر بۆ ئاراستەی وردی پینی 1 و زانیاری شوێنپێ. بەکارھێنانە باوەکان بریتین لە دیزاینی دابینکردنی وزە، بەکارخستنی مۆتۆر و گۆڕینی بار.

نەخشەی پینئاوتی پاکێجی through-hole pdip بۆ AD694JN

هیچ داتای وردی پینئاوت بەردەست نییە بۆ AD694JN.

سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.

بەکارهێنانە باوەکان

AD694JN گونجاوە بۆ 6 بەکارھێنانs: Industrial 4-20 mA Process Control, Current-Mode DAC Output Buffer, Remote Sensor Signal Conditioning, Valve and Actuator Control, Data-Acquisition and Instrumentation, Programmable Control Systems.

🏭

Industrial 4-20 mA Process Control

The AD694JN fits industrial process-control interfaces that convert a high-level measurement into a standard 4-20 mA or 0-20 mA loop. Its precalibrated 10 V input range, input buffer amplifier, and supply operation extending to +36 V provide a flexible transmitter front end. The regulated current output can drive remote valves, actuators, or sensor-conditioning equipment. Designers must verify output compliance against the actual load resistance and remote-loop supply, while also checking the open-loop alarm behavior for the intended failure-detection strategy.

🔧

Current-Mode DAC Output Buffer

The AD694JN can buffer the output of a current-mode DAC while adding a standard process-loop current stage. According to the Analog Devices AD694 datasheet, the internal input amplifier can scale the input signal or buffer a current-mode DAC output, and the device includes a programmable 10.000 V precision reference. This arrangement is useful when an upstream converter produces a current-mode signal that must drive a longer industrial cable. Validate gain, reference stability, loop compliance, and allowable output excursions before using the transmitter as the final analog output stage.

🧩

Remote Sensor Signal Conditioning

The AD694JN is suitable for remote sensor interfaces that require a current-loop output rather than a local voltage-only signal. The buffered 10 V input path can receive a suitably scaled sensor or amplifier output, while the 4-20 mA format supports monitoring across long field wiring. Single- or dual-supply operation provides additional topology flexibility for industrial equipment. The installation must include appropriate input scaling, grounding or isolation strategy, surge protection, and an output-compliance check that accounts for cable resistance and the power available at the transmitter end.

⚡

Valve and Actuator Control

The AD694JN can provide the current-loop interface used by control equipment that operates valves, actuators, and related process hardware. Its 4-20 mA range is directly aligned with conventional industrial current loops, and the alternative 0-20 mA mode supports legacy systems. The 16-pin PDIP package also suits through-hole control boards where a surface-mount-only redesign would be undesirable. Confirm that the actuator receiver accepts the selected range, that maximum loop voltage remains within device limits, and that loss-of-signal behavior is acceptable for the controlled process.

📺

Data-Acquisition and Instrumentation

The AD694JN is appropriate for laboratory or data-acquisition equipment that must present an industrial-compatible current output to a recorder or controller. Its input buffer accepts high-level signals, while the precalibrated 10 V range and programmable 10.000 V reference support controlled excitation and measurement channels. Unlike a high-voltage output amplifier, the current transmitter maintains the familiar 4-20 mA interface across field wiring. Engineers should account for loop compliance, output accuracy, grounding, and the open-loop alarm state when integrating it with data-acquisition hardware.

🔧

Programmable Control Systems

The AD694JN can act as the analog output stage of a programmable controller that must communicate with industrial field equipment. The input buffer may scale a controller-generated voltage or buffer a current-mode DAC, and the transmitter supports both 4-20 mA and 0-20 mA outputs. Its supply capability to +36 V supports a broad range of loop-power arrangements. The controller design must avoid driving the output outside its compliance region and should implement a defined fault state for power loss, open-loop wiring, or invalid input conditions.

What is the AD694JN and what does it do?
The AD694JN is a monolithic current transmitter that converts a high-level input signal into a standard 4-20 mA or 0-20 mA current-loop output. According to the Analog Devices AD694 datasheet, it is intended to drive valves, actuators, and other process-control devices. Its input buffer can scale the source signal or buffer a current-mode DAC output, while the integrated current transmitter supplies the regulated loop current.
What are the key specifications of AD694JN that engineers should know?
The AD694JN is a 16-pin PDIP current transmitter with 4-20 mA and 0-20 mA output ranges, a precalibrated 10 V input range, and a programmable 10.000 V precision reference. According to the Analog Devices AD694 datasheet, it supports single- or dual-supply operation, includes an input buffer and open-loop alarm, and operates from a supply extending to +36 V. These features support industrial process-control and measurement interfaces.
Where can I download the AD694JN datasheet PDF?
The official AD694 datasheet PDF is available from Analog Devices at https://www.analog.com/media/en/technical-documentation/data-sheets/AD694.pdf. The document contains the device description, electrical characteristics, application information, and package details for the AD694 family, including the AD694JN ordering option. Use the manufacturer's PDF for final design values, test conditions, and pin-level implementation details.
Where can I find the AD694JN pinout?
Use the pin-description table and package drawing in the Analog Devices AD694 datasheet to assign the AD694JN connections. The AD694JN is offered in a 16-pin PDIP package. Its input amplifier, precision reference, supply pins, feedback components, and current-loop output make exact pin assignment important; connect unused or unconfigured nodes only as directed by the manufacturer circuit and pin descriptions.
Can the AD694JN operate from a single supply?
Yes, the AD694JN supports single- or dual-supply operation according to the Analog Devices AD694 datasheet. Single-supply use simplifies circuit architecture, while dual-supply operation can provide additional headroom or signal-level flexibility. The appropriate configuration depends on the selected input range, reference arrangement, output compliance, and load resistance, so verify the complete operating point against the datasheet.
What input range does the AD694JN support?
The AD694JN provides a precalibrated 10 V input range and includes a programmable 10.000 V precision voltage reference. According to the Analog Devices AD694 datasheet, the input signal is buffered by an input amplifier that can either scale the incoming voltage or provide drive for a current-mode DAC. Use the reference and feedback guidance in the datasheet when setting the intended input range.
What applications are best suited for the AD694JN?
The AD694JN is best suited to industrial process-control loops that require a standardized current output. Typical uses include driving valves, actuators, remote sensor transmitters, programmable controllers, and current-mode DAC output stages. Its 4-20 mA output, 10 V precalibrated input range, input buffer, and open-loop alarm support instrumentation where the field interface must remain usable over long wiring distances.
What is the difference between AD694JN and AD694JNZ?
The AD694JN is the 16-pin PDIP ordering option associated with the AD694 current transmitter, while AD694JNZ is separately listed as a 16-PDIP current-transmitter IC. A published comparison indicates that their functional characteristics and several major parameters are similar, but that some electrical characteristics differ. Treat AD694JNZ as a qualified comparison item rather than an unconditional replacement, and verify temperature grade, electrical limits, and ordering details before substitution.
Is the AD694JN the same as AD694AQ?
No, the AD694JN and AD694AQ should not be assumed to be interchangeable. The AD694JN is identified as a 16-pin PDIP monolithic current transmitter, while published comparison information classifies AD694AQ as an instrumentation-amplifier product. Although both can appear in signal-conditioning searches, their functions, pin assignments, and circuit requirements differ. Use the AD694 datasheet and the specific AD694AQ documentation for any signal-chain comparison.
What is the best drop-in replacement for AD694JN?
No verified drop-in replacement was established for the AD694JN. The cross-reference search did not identify a manufacturer-confirmed equivalent that is simultaneously pin-to-pin compatible, electrically equivalent, and available in the same 16-pin PDIP footprint. AD694JNZ merits comparison because it is also listed in a 16-PDIP package, but its temperature and electrical differences must be reviewed before it is treated as a replacement.
What can replace the AD694JN in a 4-20 mA transmitter circuit?
A direct replacement should provide the same 16-pin PDIP pinout, 4-20 mA output topology, 10 V precalibrated input range, compatible supply limits, and equivalent current-loop compliance. No cross-brand part meeting those conditions was confirmed for the AD694JN. If the original device is unavailable, evaluate the AD694JNZ ordering option first and compare its exact electrical characteristics, temperature rating, and lifecycle status against the original design.
When should I choose the AD694JN over another current transmitter?
Choose the AD694JN when the design specifically needs a high-level input buffered into a 4-20 mA or 0-20 mA loop and the 16-pin PDIP format fits the board. It is particularly relevant when a precalibrated 10 V input range, programmable 10.000 V reference, open-loop alarm, and supply operation to +36 V align with the process interface. A different device is preferable when it offers verified pin compatibility, a required temperature grade, or better compliance for a different load.
Is the AD694JN suitable for industrial sensor and actuator control?
Yes, the AD694JN is designed for process-control applications involving valves, actuators, and standard 4-20 mA current loops. According to the Analog Devices AD694 datasheet, it accepts high-level input signals and can buffer a current-mode DAC output. Industrial suitability still depends on the complete circuit meeting the loop-supply voltage, output-compliance, grounding, protection, and environmental requirements of the installed equipment.
How should I design the power and output loop for AD694JN?
Design the AD694JN loop from the maximum load resistance, required 4-20 mA current, remote-loop supply, and transistor or protection-network voltage drop. The AD694 datasheet specifies wide output-compliance capability and operation extending to +36 V, but the allowable combination of load, supply, and output state must still be checked. Keep the high-current loop path compact and protect the output against accidental overvoltage or reverse-current events.
Where can I buy AD694JN and what are its price and lead time?
Use the Request a Quote form on this page to obtain current AD694JN availability, commercial terms, and lead time. The component is also listed in a 16-pin PDIP tube format by multiple product records, but commercial status and lead time can change by date, quantity, and market conditions. Request a formal quotation for the exact AD694JN suffix before committing the component to a production schedule.

داتای سەرچاوەی ئەندازیاری بۆ AD694JN — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.

ڕێنمایی هەڵبژاردن

Choose the AD694JN when the design needs a high-level signal converted into a standard 4-20 mA or 0-20 mA current-loop output and the board can accommodate a 16-pin PDIP device. Its precalibrated 10 V input range, buffered input path, programmable 10.000 V reference, open-loop alarm, single- or dual-supply operation, and supply capability extending to +36 V make it suitable for process-control, actuator, remote-sensor, and data-acquisition interfaces. The AD694JNZ is a useful comparison item because product records identify it as a 16-PDIP current-transmitter IC, but it should not be treated as an unconditional replacement until temperature grade, electrical limits, lifecycle status, and pin-level behavior are reconciled. No verified cross-brand drop-in equivalent was established for the original circuit, so board redesign or manufacturer-guided substitution may be necessary if alternate sourcing is required.

بەراوردکردن لەگەڵ جێگرەوەکان

پارامەتر ئەم بەرهەمە
Product Type Monolithic current transmitter
Brand Analog Devices
Package 16-pin PDIP
Primary Output Range 4-20 mA
Additional Output Range 0-20 mA
Precalibrated Input Range 10 V
Precision Voltage Reference Programmable 10.000 V
Maximum Supply Voltage +36 V
Supply Configuration Single or dual supply

تێبینییەکانی دیزاین

Check the complete loop power budget rather than only the transmitter supply rating. The maximum load resistance is governed by output compliance, loop current, remote supply voltage, and any protection-device drops. Use the Analog Devices AD694 datasheet to select the operating region, then verify the worst case across minimum supply, maximum load, and the 4-20 mA endpoint. Keep the high-current output path short and separate it from sensitive input routing.

Place the input, feedback, reference, and output-compensation components close to their associated AD694JN pins to reduce trace resistance and parasitic pickup. Route the 4-20 mA loop as a high-current path and keep it away from the buffered 10 V input and precision reference. The 16-pin PDIP footprint requires adequate through-hole spacing for the supply and output connections. Review the manufacturer's application schematic and grounding arrangement before finalizing the board layout.

Do not assume that any similarly described 4-20 mA transmitter is pin-compatible with the AD694JN. The input range, reference implementation, feedback connections, open-loop alarm behavior, output-compliance limits, and supply arrangement must all match the original circuit. For replacement work, compare the AD694JNZ ordering option only after reviewing its exact electrical and temperature-grade differences. Use the manufacturer pin table and application circuit as the authority for each connection.

زانیاری پابەندبوون

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
بێ قوڕقوشم
Unknown
بێ ھالۆجین
Unknown
کانزا ناکۆکەکان
Unknown

The available product documentation identifies the AD694 as industrial process-control equipment but does not state specific RoHS, REACH, lead-free, halogen-free, conflict-mineral, or automotive qualification status.

داتا پشتڕاستکراوەتەوە لە: 2026-11-09 — داتا لەلایەن تیمی ئەندازیاری پێکھاتەکانی XAIPART پشتڕاستکراوەتەوە و ڕێکخراوە

گەڕانە پەیوەندیدارەکان

ad694jn datasheet AD694JN datasheet PDF AD694JN pinout AD694JN 4-20mA transmitter AD694JN 16-PDIP AD694JN equivalent AD694JN replacement AD694JN cross reference AD694JN vs AD694JNZ Analog Devices AD694JN AD694JN price AD694JN stock AD694JN application circuit AD694JN process control interface

پێکهاتە و زاراوە پەیوەندیدارەکان

Analog Devices AD694JN AD694JNZ AD694 monolithic current transmitter current transmitter process-control interface 4-20 mA current loop 0-20 mA output input buffer amplifier current-mode DAC precision voltage reference 10 V input range 10.000 V reference open-loop alarm output compliance single-supply operation dual-supply operation 16-pin PDIP PDIP package family through-hole package industrial process control valve control actuator control remote sensor interface
داواکاری نرخی خێرا RFQ
وردەکارییەکانی تەواو پڕ بکەرەوە — تیمی فرۆشتنی ئێمە لە ماوەی 24 کاتژمێردا وەڵام دەداتەوە
ژمارەی پارچە بەرهەمهێنەر پاکەت QTY نرخی ئامانج کۆی گشتی
✓
نرخەکە نێردرا!

لە ماوەی ٢٤ کاتژمێردا وەڵامی ئیمەیڵەکەت دەدەینەوە

1
داواکاری نرخ پێشکەشکرا
2
نرخپێدان وەرگیرا
3
داواکاری دانرا
4
پارەدان
5
نێردرا
6
گەیەنراوە
بینینی وردەکاریی داواکاری نرخ