AD694JN - 4-20mA Current Transmitter | Analog Devices
MPN: AD694JN ✓ AktifAD694JN Ringkasan
A current transmitter is a process-control interface that converts a voltage or current-mode input into the standardized 4-20 mA signal used by valves, actuators, transmitters, and remote sensors. Its place in the signal chain is between a sensor or controller and an industrial field loop. This interface category provides a robust way to transfer measurement information over long cables while limiting signal corruption and allowing one measurement input to be monitored remotely.
The AD694JN includes a precalibrated 10 V input range, a programmable 10.000 V precision voltage reference, an input buffer amplifier, and open-loop alarm functionality. According to the Analog Devices AD694 datasheet, the buffered input can scale the incoming signal or buffer the output of a current-mode DAC. These features make the device useful when the source is a high-level process signal or a current-mode converter requiring additional drive capability.
Operation from a single or dual supply gives the designer flexibility when constructing isolated or non-isolated measurement systems. The manufacturer specifies a wide power-supply range extending to +36 V and includes a wide output-compliance capability. These characteristics are especially relevant to industrial systems where loop power may be provided remotely and the transmitter must maintain useful output current across the required load resistance.
Typical uses include 4-20 mA process transmitters, programmable controllers, industrial sensor interfaces, current-mode DAC output buffers, data-acquisition systems, and control loops for valves or actuators. The AD694JN is also suited to laboratory and test equipment requiring a standard analog current output rather than a voltage-only measurement interface.
Designers should verify the selected supply configuration, input range, feedback-network values, output-compliance voltage, and loop load against the Analog Devices AD694 datasheet before releasing a PCB. Because this is a 16-pin PDIP package, adequate through-hole spacing and copper routing for power and current-loop currents are required. Do not add filtering or protection components to the loop without checking their effect on output accuracy and compliance.
This product page consolidates the manufacturer's device description, package information, application context, engineering cautions, and verified replacement status. It is intended to accelerate component identification and board-level planning while keeping every claimed electrical value traceable to the AD694 documentation.
Pilihan pengganti yang segera untuk AD694JN — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.
AD694JNZ
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
AD694JN Penilaian maksimum & Ciri-ciri Elektrik
| Product Type | Monolithic current transmitter |
| Primary Output Range | 4-20 mA |
| Additional Output Range | 0-20 mA |
| Precalibrated Input Range | 10 V |
| Precision Voltage Reference | Programmable 10.000 V |
| Maximum Supply Voltage | +36 V |
| Supply Configuration | Single or dual supply |
| Input Buffer Amplifier | Included |
| Open-Loop Alarm | Supported |
| Kemasan | 16-pin PDIP |
| Package Type | Through-hole PDIP |
Panduan Konfigurasi Pin AD694JN through-hole pdip
Konfigurasi pin untuk AD694JN (through-hole pdip pakai). Peranti kuasa ini mempunyai terminal kawat, buang, dan sumber. Untuk pakai non-polarized, rujuk dokumen pengeluar untuk orientasi pin 1 tepat dan perincian kebentuk.
Tiada data garisan pin yang diperoleh untuk AD694JN.
Rujuk kepada lembaran data untuk konfigurasi pin penuh.
Aplikasi Biasa
AD694JN patut untuk 6 aplikasis: Industrial 4-20 mA Process Control, Current-Mode DAC Output Buffer, Remote Sensor Signal Conditioning, Valve and Actuator Control, Data-Acquisition and Instrumentation, Programmable Control Systems.
Industrial 4-20 mA Process Control
The AD694JN fits industrial process-control interfaces that convert a high-level measurement into a standard 4-20 mA or 0-20 mA loop. Its precalibrated 10 V input range, input buffer amplifier, and supply operation extending to +36 V provide a flexible transmitter front end. The regulated current output can drive remote valves, actuators, or sensor-conditioning equipment. Designers must verify output compliance against the actual load resistance and remote-loop supply, while also checking the open-loop alarm behavior for the intended failure-detection strategy.
Current-Mode DAC Output Buffer
The AD694JN can buffer the output of a current-mode DAC while adding a standard process-loop current stage. According to the Analog Devices AD694 datasheet, the internal input amplifier can scale the input signal or buffer a current-mode DAC output, and the device includes a programmable 10.000 V precision reference. This arrangement is useful when an upstream converter produces a current-mode signal that must drive a longer industrial cable. Validate gain, reference stability, loop compliance, and allowable output excursions before using the transmitter as the final analog output stage.
Remote Sensor Signal Conditioning
The AD694JN is suitable for remote sensor interfaces that require a current-loop output rather than a local voltage-only signal. The buffered 10 V input path can receive a suitably scaled sensor or amplifier output, while the 4-20 mA format supports monitoring across long field wiring. Single- or dual-supply operation provides additional topology flexibility for industrial equipment. The installation must include appropriate input scaling, grounding or isolation strategy, surge protection, and an output-compliance check that accounts for cable resistance and the power available at the transmitter end.
Valve and Actuator Control
The AD694JN can provide the current-loop interface used by control equipment that operates valves, actuators, and related process hardware. Its 4-20 mA range is directly aligned with conventional industrial current loops, and the alternative 0-20 mA mode supports legacy systems. The 16-pin PDIP package also suits through-hole control boards where a surface-mount-only redesign would be undesirable. Confirm that the actuator receiver accepts the selected range, that maximum loop voltage remains within device limits, and that loss-of-signal behavior is acceptable for the controlled process.
Data-Acquisition and Instrumentation
The AD694JN is appropriate for laboratory or data-acquisition equipment that must present an industrial-compatible current output to a recorder or controller. Its input buffer accepts high-level signals, while the precalibrated 10 V range and programmable 10.000 V reference support controlled excitation and measurement channels. Unlike a high-voltage output amplifier, the current transmitter maintains the familiar 4-20 mA interface across field wiring. Engineers should account for loop compliance, output accuracy, grounding, and the open-loop alarm state when integrating it with data-acquisition hardware.
Programmable Control Systems
The AD694JN can act as the analog output stage of a programmable controller that must communicate with industrial field equipment. The input buffer may scale a controller-generated voltage or buffer a current-mode DAC, and the transmitter supports both 4-20 mA and 0-20 mA outputs. Its supply capability to +36 V supports a broad range of loop-power arrangements. The controller design must avoid driving the output outside its compliance region and should implement a defined fault state for power loss, open-loop wiring, or invalid input conditions.
Data referensi kejuruteraan untuk AD694JN — perbandingan, panduan rancangan, dan maklumat kesediaan
Panduan Pilihan
Perbandingan dengan Gantian
| Parametr | Produk Ini |
|---|---|
| Product Type | Monolithic current transmitter |
| Brand | Analog Devices |
| Package | 16-pin PDIP |
| Primary Output Range | 4-20 mA |
| Additional Output Range | 0-20 mA |
| Precalibrated Input Range | 10 V |
| Precision Voltage Reference | Programmable 10.000 V |
| Maximum Supply Voltage | +36 V |
| Supply Configuration | Single or dual supply |
Catatan Desain
Check the complete loop power budget rather than only the transmitter supply rating. The maximum load resistance is governed by output compliance, loop current, remote supply voltage, and any protection-device drops. Use the Analog Devices AD694 datasheet to select the operating region, then verify the worst case across minimum supply, maximum load, and the 4-20 mA endpoint. Keep the high-current output path short and separate it from sensitive input routing.
Place the input, feedback, reference, and output-compensation components close to their associated AD694JN pins to reduce trace resistance and parasitic pickup. Route the 4-20 mA loop as a high-current path and keep it away from the buffered 10 V input and precision reference. The 16-pin PDIP footprint requires adequate through-hole spacing for the supply and output connections. Review the manufacturer's application schematic and grounding arrangement before finalizing the board layout.
Do not assume that any similarly described 4-20 mA transmitter is pin-compatible with the AD694JN. The input range, reference implementation, feedback connections, open-loop alarm behavior, output-compliance limits, and supply arrangement must all match the original circuit. For replacement work, compare the AD694JNZ ordering option only after reviewing its exact electrical and temperature-grade differences. Use the manufacturer pin table and application circuit as the authority for each connection.
Maklumat Kesediaan
The available product documentation identifies the AD694 as industrial process-control equipment but does not state specific RoHS, REACH, lead-free, halogen-free, conflict-mineral, or automotive qualification status.