Analog Devices

AD725AR - RGB to NTSC/PAL Video Encoder IC | Analog Devices

MPN: AD725AR ✓ چالاک
Less than 1 microamp Id NTSC and PAL Rds(on) SOIC-16 (16-lead plastic small-outline) Package
MOQ: 1 |

AD725AR گشتی

The Analog Devices AD725AR is a low-cost RGB to NTSC/PAL video encoder integrated circuit that converts red, green and blue color component inputs into a composite video signal, while also providing separate chrominance and luminance (S-Video) outputs, all in a 16-lead SOIC package.

An RGB-to-NTSC/PAL encoder sits at the boundary between graphics and video: it takes the parallel digital-equivalent RGB voltages produced by a graphics controller, CRT/LCD video card, character generator or test pattern source and converts them into the modulated composite video waveform that analog monitors, VCRs, and broadcast equipment expect. In the component hierarchy it belongs to the video interface IC family, which itself is a subset of interface ICs, mixed-signal semiconductors and, at the broadest level, integrated circuits.

Key features of the AD725AR include composite video output for both NTSC and PAL standards, simultaneous chrominance and luminance (S-Video) outputs, a dedicated luma trap (YTRAP) port that reduces cross-color artifacts, TTL-compatible logic levels that also satisfy 3 V CMOS system requirements, an integrated delay line and auto-tuned filters, the ability to drive 75-ohm reverse-terminated loads, and low power consumption. Power-down operation allows the device to be held below 1 microamp of supply current for portable or power-sensitive equipment.

Technically, the AD725AR accepts RGB inputs at TTL levels, internally encodes the color difference information onto a color subcarrier, filters it to the correct bandwidth for NTSC or PAL, and combines it with the luminance path and synchronization information to produce a composite output. The on-chip delay line and auto-tuned filters remove the need for external crystal-controlled oscillator components and hand-matched traps, which is what makes the part low cost while still suitable for consumer and industrial video gear.

Typical uses include video card and CRT monitor interface logic, industrial and instrumentation video panels, video test equipment and pattern generators, security and surveillance camera analog output chains, and legacy computer and arcade display hardware being maintained or adapted.

When designing around the AD725AR, remember that the luma trap port must be handled correctly to avoid cross-color, and that output drive is specified for 75-ohm reverse-terminated loads, so downstream cable and impedance matching determine the usable signal amplitude.

This page consolidates the AD725AR feature set, package and ordering variants, drop-in replacements and practical design notes into one reference so you can qualify the encoder without digging through several documents.

جێگرەوەکانی جێگۆڕکێ بۆ AD725AR — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.

جۆرەکان لەم زنجیرەیەدا

مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ AD725AR (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Luma Trap Port, Package, Function, Composite Video Output, Logic Input Levels.

Analog Devices
Package: 16-pin SOIC (SO-16, R suffix on Analog Devices R-suffix tape-and-reel grade)
Function: RGB to NTSC/PAL video encoder
بەراوردکردن لەگەڵ AD725AR →
Analog Devices
Luma Trap Port: Yes (eliminates cross-color artifacts)
Function: RGB to NTSC/PAL Video Encoder
Composite Video Output: Yes (NTSC and PAL)
بەراوردکردن لەگەڵ AD725AR →
Analog Devices
Luma Trap Port: Yes (YTRAP, reduces cross-color artifacts)
Package: 16-SOIC (0.295 in, 7.50 mm width)
Function: RGB to NTSC/PAL Video Encoder
بەراوردکردن لەگەڵ AD725AR →

AD725ARZ-R7

✅ جێگرەوەی ڕاستەوخۆ
Analog Devices
📦 SOIC-16
RGB to NTSC/PAL Video Encoder · Yes (NTSC and PAL) · Yes (separate chrominance and luminance) · Yes (eliminates cross-color artifacts) · TTL logic levels · Yes · Surface Mount · 16-SOIC (0.295 in, 7.50 mm width)

پەیوەندی بۆ نرخ

بینینی داتاشیت →

AD725AR-REEL7

✅ جێگرەوەی ڕاستەوخۆ
📦 SOIC-16
Identical AD725 device in the same SOIC 16-pin package; cross-reference data confirms consistent performance parameters, functional characteristics and terminals, 0% parameter difference

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

AD725ARZ

✅ جێگرەوەی ڕاستەوخۆ
Analog Devices
📦 SOIC-16
RGB to NTSC/PAL video encoder · NTSC-M, PAL-B/D/G/H/I/M/N · Analog RGB (0 V to 0.7 V) or TTL digital RGB · Composite video (NTSC/PAL), Y/C (S-Video), luma trap port · +5 V single supply · 28.63636 MHz (NTSC) / 26.84325 MHz (PAL)

پەیوەندی بۆ نرخ

بینینی داتاشیت →

AD725AR زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان

کارکردن RGB to NTSC/PAL composite video encoder
Manufacturer Analog Devices
Video Standards Supported NTSC and PAL
Composite Video Output Yes, single composite output
S-Video Outputs Separate chrominance (C) and luminance (Y) outputs
Luma Trap Port Dedicated YTRAP port for cross-color reduction
Logic Input Levels TTL compatible, supports 3 V CMOS logic systems
Output Drive Capability 75 ohm reverse-terminated loads
Integrated Delay Line Yes, on-chip delay line
Filtering Integrated auto-tuned filters
Power-Down Current Less than 1 microamp
Power Consumption Low power operation
پاکێج SOIC-16 (16-lead plastic small-outline)
ژمارەی پین 16 pins
جۆری دامەزراندن Surface mount

ڕێنمایی ڕێکخستنی پینی AD725AR soic-16 (16-lead plastic small-outline)

ڕێکخستنی پین بۆ AD725AR (پاکێجی soic-16 (16-lead plastic small-outline)). ئەم پێکھاتە ئەنالۆگە پینی چوونەژوورەوە، دەرچوون و دابینکردنی وزەی ھەیە. سەرنج بدە بە داتاشیتی بەرھەمھێنەر بۆ ڕێکخستنەکانی پینی لادانی ئۆفسێت، قەرەبووکردنەوە و چالاککردن. گونجاوە بۆ ڕێکخستنی ئیشارەت و خولەکانی بەرزکەرەوە.

نەخشەی پینئاوتی پاکێجی soic-16 (16-lead plastic small-outline) بۆ AD725AR

هیچ داتای وردی پینئاوت بەردەست نییە بۆ AD725AR.

سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.

بەکارهێنانە باوەکان

AD725AR گونجاوە بۆ 6 بەکارھێنانs: Legacy CRT Monitor and Video Card Interface, Industrial Instrumentation and Test Panels, Security Camera and Surveillance Video Output, Video Test and Pattern Generation Equipment, Consumer Electronics and Arcade Display Hardware, Broadcast and Analog Studio Peripheral Equipment.

📺

Legacy CRT Monitor and Video Card Interface

The AD725AR was designed for exactly this path: a graphics controller or video card presents red, green and blue signals that must become an NTSC or PAL composite signal for an analog monitor. Because the encoder carries its own delay line and auto-tuned filters, no crystal oscillator or hand-matched trap network is needed, which keeps the analog front end small and repeatable across production lots. TTL-compatible inputs also mean 74HCT-family drivers or modern 3 V CMOS controllers can feed the RGB pins directly, and the separate chrominance and luminance outputs give the design team S-Video capability from the same silicon. The 16-lead SOIC footprint is straightforward to route, and the composite output is specified to drive 75-ohm reverse-terminated loads, matching the terminated coax runs typical of monitor cabling.

🏭

Industrial Instrumentation and Test Panels

Industrial test equipment and instrumentation panels often need to display a simple generated pattern or measurement result on a standard analog video display without pulling in a full graphics pipeline. The AD725AR answers that need with one IC: RGB inputs in, composite video out, with NTSC and PAL supported so the same hardware can ship to different regional customers. Its integrated delay line and auto-tuned filters eliminate the external discrete encoder assemblies such designs usually need, which reduces board area and the number of parts that must be sourced. The low power-draw operation, including the less-than-1-microamp power-down state described in the AD725 data sheet, also suits bench instruments where a power-down idle state is desirable between measurements.

🎥

Security Camera and Surveillance Video Output

Compact surveillance and CCTV camera electronics frequently need to expose an analog composite video output in parallel with a digital stream, so that legacy monitors, DVRs and recording equipment can still be attached. The AD725AR provides that analog path from an RGB or luminance-plus-color source at very low component cost, with the composite output able to drive 75-ohm reverse-terminated cable runs directly. Auto-tuned on-chip filtering means the chrominance bandwidth is already set for the chosen standard, avoiding the drift and assembly variance that external trap networks introduce over temperature and time. Power-down capability is valuable in cameras that run mostly idle, and the small SOIC footprint keeps the encoder compact inside small camera housings.

🖥️

Video Test and Pattern Generation Equipment

Test equipment that produces bars, grays, color ramps or synthesized composite signals for aligning and servicing monitors and broadcast chains is a natural fit for the AD725AR. Because the encoder accepts RGB at logic levels, a microcontroller or small FPGA can generate arbitrary patterns in software or hardware and feed them straight into the chip, giving a fully programmable test source. NTSC and PAL support in one device means a single instrument can service multiple standards, and the luma trap port lets a technician or the design team fine-tune the luminance trap to suppress cross-color during alignment. The composite output's ability to drive 75-ohm reverse-terminated loads supports direct connection to distribution amplifiers and monitor inputs in a test bench.

🎮

Consumer Electronics and Arcade Display Hardware

Consumer products and arcade machines built on vintage video standards still need a dependable composite output stage, and the AD725AR delivers it at low cost in a 16-lead SOIC. It removes the need for a discrete color-modulation board with a crystal oscillator, delay line and matched traps, which is exactly why it became popular in 1980s and 1990s consumer and amusement designs. Today it remains valuable for maintaining legacy hardware, for aftermarket retro-gaming peripherals, and for educational kits that teach composite video principles with a real, documented part. Its logic inputs are TTL-compatible, so vintage TTL glue logic and modern 3 V CMOS controllers can both drive it without level-shifting.

🌐

Broadcast and Analog Studio Peripheral Equipment

In broadcast and production environments, older analog decks, frame synchronizers and small video switchers frequently rely on composite NTSC or PAL sources, and the AD725AR can act as the final RGB-to-composite stage in such a chain. Separate chrominance and luminance outputs allow the signal to be routed either as full composite or as S-Video, which is useful when a facility still has a mix of both connector types. The low-noise, auto-tuned internal filtering keeps the modulation characteristics stable over temperature, and the power-down state allows the encoder to be disabled when a channel is not in use. Because the composite output is specified to drive 75-ohm reverse-terminated loads, it can feed short cable runs and patch panels directly.

کورتەی بەرهەمە پێشنیارکراوەکان

What is the AD725AR and what does it do?
The AD725AR is a low-cost RGB to NTSC/PAL video encoder integrated circuit from Analog Devices. It accepts red, green and blue color component inputs and converts them into a composite video output, while simultaneously delivering separate chrominance (C) and luminance (Y) outputs for S-Video. According to the AD725 data sheet, the device includes a luma trap port, TTL-compatible logic levels, an integrated delay line and auto-tuned filters, and it drives 75-ohm reverse-terminated loads directly. It is packaged in a 16-lead SOIC and targets consumer and industrial video equipment where a simple, low-cost composite video path is required.
What are the key specifications of AD725AR that engineers should know?
The AD725AR is a 16-lead SOIC RGB to NTSC/PAL video encoder supporting both NTSC and PAL composite output, plus separate chrominance and luminance (S-Video) outputs. Notable features listed in the AD725 data sheet include a dedicated luma trap (YTRAP) port to reduce cross-color artifacts, TTL-compatible logic levels that also meet 3 V CMOS system requirements, an integrated delay line, integrated auto-tuned filters, drive capability for 75-ohm reverse-terminated loads, and a power-down mode that reduces supply current to less than 1 microamp for portable applications.
What package does the AD725AR come in, and how many pins does it have?
The AD725AR ships in a 16-lead plastic small-outline package, designated SOIC-16, for surface-mount assembly. Ordering suffixes distinguish the mechanical and packaging options: the -R7 and -REEL7 variants are tape-and-reel shipments of the same 16-lead SOIC device, while the base AD725AR designation refers to the standard commercial-temperature part. Because all of these variants share the same 16-lead SOIC footprint and pinout, they are direct drop-in substitutes for one another when the correct orderable marking and packaging form factor are selected.
Does the AD725AR support both NTSC and PAL video standards?
Yes, the AD725AR supports both NTSC and PAL composite video output. The encoder generates a modulated color subcarrier and composite signal in the format expected by analog NTSC and PAL monitors, videotape equipment and broadcast gear. Because the subcarrier and filter characteristics are handled internally with auto-tuned filters, the same silicon serves both standards without external trap or oscillator adjustment, which simplifies inventory for manufacturers building products for multiple export markets. The separate chrominance and luminance outputs also allow the device to feed S-Video equipment directly.
What is the luma trap (YTRAP) port on the AD725AR used for?
The YTRAP port on the AD725AR provides a means of reducing cross-color artifacts caused by subcarrier frequency components present in the luminance signal. In composite video, the color subcarrier sits inside the luminance band, so a portion of it can leak into the luminance path and appear as unwanted color dots or streaks on screen. The AD725 data sheet explains that exposing this node to a properly chosen network allows the luminance trap to be tuned, and that leaving it unused degrades picture quality. Design accordingly and treat YTRAP as an active filter node, not a no-connect.
What logic levels does the AD725AR accept, and can it be driven from 3 V CMOS systems?
The AD725AR uses TTL-compatible logic levels for its digital inputs, and the AD725 data sheet states that these levels support the logic requirements of 3 V CMOS systems as well. In practice this means you can drive the RGB and control inputs from 74HCT-family logic or modern 3 V CMOS controllers without level translation. Combined with the integrated delay line, auto-tuned filters and on-chip color modulation, this simplifies the interface between a graphics generator and the encoder, and it is one reason the device is widely used in legacy video and monitor designs.
AD725AR vs AD725ARZ-R7 - what is the difference and which should I pick?
The AD725AR and the AD725ARZ-R7 are the same AD725 RGB to NTSC/PAL encoder die in the same 16-lead SOIC package, so they are electrically and pin compatible. The difference is ordering and packaging: the -R7 suffix denotes the tape-and-reel shipment form used for automated assembly, while the base AD725AR designation is the standard commercial ordering code. According to the AD725 data sheet and Analog Devices product page for the AD725, both variants share identical functional characteristics and terminal assignments, so either can populate the same footprint; choose the packaging form that matches your assembly process.
What is the best drop-in replacement for the AD725AR?
The best drop-in replacements for the AD725AR are the other orderable forms of the same Analog Devices AD725 device in the 16-lead SOIC package, specifically the AD725ARZ-R7 and the AD725AR-REEL7. Manufacturer and distributor comparison data describe these as complete replacements whose main performance parameters and functional characteristics are consistent and whose terminals and packages match, so no circuit modification is required. Because the AD725 is a mature, long-lived video encoder, the most practical alternative for an existing design is the same family in the packaging form your assembler requires.
What can replace the AD725AR in an existing RGB-to-video design?
Anything that replaces the AD725AR in an existing design must offer the same 16-lead SOIC footprint, the same RGB input and composite/S-Video output pin assignments, and TTL-compatible logic inputs, and it should also integrate the delay line and filters. The AD725ARZ-R7 and AD725AR-REEL7 satisfy this because they are the same die in the same package. If you need a functionally similar but not pin-compatible solution, you would have to redesign the board around a discrete or FPGA-based RGB-to-composite encoder, which is a substantial rework rather than a substitution.
Is the AD725AR the same as the AD725AR-REEL7?
Yes, the AD725AR and the AD725AR-REEL7 are functionally identical devices; the -REEL7 code simply identifies the reel-packed shipping option of the AD725AR, and distributor cross-reference listings describe the AD725AR-REEL7 as a complete replacement in the same SOIC 16-pin package with consistent terminals and functional characteristics. The AD725 data sheet and the Analog Devices AD725 product page both list the AD725 family in the 16-lead SOIC. For prototyping you can order the standard AD725AR; for production volume you would normally use the -REEL7 form factor.
Where can I download the AD725AR datasheet PDF?
The AD725AR data sheet PDF is published by Analog Devices and is available directly from the manufacturer at https://www.analog.com/media/en/technical-documentation/data-sheets/AD725.pdf, with the product landing page at https://www.analog.com/en/products/ad725.html. The document contains the feature list, the NTSC/PAL encoder description, the YTRAP explanation, the power-down behavior and the pin configuration. Use the manufacturer PDF as the controlling reference when assigning tracks, and use the Request a Quote form on this page if you need a quantity quotation for the AD725AR.
Where can I find the AD725AR pinout and pin configuration?
The AD725AR pin configuration is documented in the AD725 data sheet, which is published by Analog Devices as a downloadable PDF, and the part is offered in a 16-lead SOIC package. Because this page does not reproduce the manufacturer's terminal assignment table, use the pin-description and pin-configuration sections of the AD725 data sheet, together with the package drawing in the ordering guide, when assigning PCB tracks and verifying the RGB, composite and S-Video connections. The Request a Quote form on this page can provide the data sheet and ordering information for the exact suffix you need.
Where can I buy the AD725AR online?
You can request a quotation for the Analog Devices AD725AR directly through the Request a Quote form on this page, which is the fastest route to confirm stock, lead time and allocation for the 16-lead SOIC package. The part is also catalogued by authorized distributors and part-search aggregators, which is useful for cross-checking lifecycle status and regional stock. Because the AD725 is a mature device with multiple orderable suffixes, specify the packaging option you need - standard commercial or reel form - when you submit the request.
What is the price of the AD725AR?
Pricing for the AD725AR depends on order quantity, package suffix and current supplier allocation, so the live figure is shown in the pricing panel on this page and is refreshed daily; use the Request a Quote form for a binding quotation against your volume and delivery schedule. Part-search listings for the AD725AR show both a spot market entry and distributor stock positions, which is a useful sanity check on availability. When comparing options, remember that the -R7 and -REEL7 orderable forms of the same 16-lead SOIC device can be priced and stocked differently from the base AD725AR code.
What is the lead time and stock status for the AD725AR?
Lead time and stock for the AD725AR vary by suffix and by channel, so the current position should be confirmed through the Request a Quote form on this page rather than assumed. Because the AD725 is a long-lived Analog Devices video encoder with several orderable forms - the base AD725AR plus the -Z-R7 and -REEL7 tape-and-reel versions - distributors normally carry one or more of these variants in inventory, and the reel-packed forms are the ones most readily available for automated assembly. Request the quote with your required packaging form and target date for an accurate answer.
When should I choose the AD725AR over a discrete or FPGA-based RGB-to-video encoder?
Choose the AD725AR when you need a self-contained, low-cost composite video path in a fixed NTSC or PAL format and the design is already tied to the 16-lead SOIC footprint. It integrates the delay line, auto-tuned filters, modulation and S-Video outputs, so it replaces an entire discrete encoder board with one IC and a small decoupling network. Choose a discrete or FPGA-based approach instead when you need programmable output formats, digital video interfaces such as LVDS or HDMI, multi-standard support, or features beyond analog composite encoding.
Is the AD725AR suitable for battery-powered and portable video equipment?
Yes, the AD725AR is well suited to portable and power-sensitive equipment. The AD725 data sheet states that for portable or other power-sensitive applications the device can be powered down to less than 1 microamp of current consumption, and it is characterized as a low-power part overall. Combined with the fact that it needs no external crystal-controlled oscillator or matched filter network, the AD725AR lets a portable instrument or handheld video source produce NTSC or PAL composite output from an existing RGB bus while consuming minimal standby power between uses.

داتای سەرچاوەی ئەندازیاری بۆ AD725AR — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.

ڕێنمایی هەڵبژاردن

Choose the AD725AR when your design must turn RGB color components into an analog NTSC or PAL composite signal and you want the smallest possible analog front end. It is a strong choice when the board is already laid out around the 16-lead SOIC footprint, when legacy monitors or composite-equipped equipment are the target, and when the low-power power-down state matters for portable products. Prefer the -R7 or -REEL7 orderable forms for automated assembly, and the standard form for prototype quantities. If instead your product needs digital video interfaces, programmable output formats, or support for standards beyond NTSC and PAL, this encoder is the wrong tool and a discrete or FPGA-based video path is the better fit. Because all listed alternatives are the same AD725 die in the same package, the real decision is packaging, sourcing and availability rather than electrical fit.

بەراوردکردن لەگەڵ جێگرەوەکان

پارامەتر ئەم بەرهەمە AD725ARZ-R7 AD725AR-REEL7 AD725ARZ
Package SOIC-16 SOIC-16 - same SOIC-16 - same SOIC-16 - same
Brand Analog Devices Analog Devices Analog Devices Analog Devices
Function RGB to NTSC/PAL composite video encoder RGB to NTSC/PAL composite video encoder RGB to NTSC/PAL composite video encoder RGB to NTSC/PAL composite video encoder
Video Standards NTSC and PAL NTSC and PAL NTSC and PAL NTSC and PAL
Output Configuration Composite plus separate chrominance and luminance (S-Video) Composite plus separate chrominance and luminance (S-Video) Composite plus separate chrominance and luminance (S-Video) Composite plus separate chrominance and luminance (S-Video)
Luma Trap Port Yes (YTRAP) for cross-color reduction Yes (YTRAP) Yes (YTRAP) Yes (YTRAP)
Logic Input Levels TTL compatible, supports 3 V CMOS systems TTL compatible, supports 3 V CMOS systems TTL compatible, supports 3 V CMOS systems TTL compatible, supports 3 V CMOS systems
Integrated Delay Line and Filters Yes, integrated delay line and auto-tuned filters Yes, integrated Yes, integrated Yes, integrated
Output Load Capability 75 ohm reverse-terminated loads 75 ohm reverse-terminated loads 75 ohm reverse-terminated loads 75 ohm reverse-terminated loads
Power-Down Current Less than 1 microamp Less than 1 microamp Less than 1 microamp Less than 1 microamp

جیاکەرەوە سەرەکییەکان

  • All-in-one composite video encoding with on-chip delay line and auto-tuned filters (بەراورد بەAD725ARZ-R7)
  • Simultaneous composite and S-Video outputs (بەراورد بەAD725AR-REEL7)
  • Single-source ordering flexibility across packaging forms (بەراورد بەAD725ARZ)

تێبینییەکانی دیزاین

Treat the YTRAP pin as an active filter node rather than a no-connect. The AD725 data sheet identifies the luma trap port as the means of reducing cross-color artifacts caused by subcarrier components appearing in the luminance path. If the trap network is omitted or left floating, color bleeding becomes visible on the composite output. Follow the network and component tolerances given in the manufacturer's application guidance for the target standard, and verify the result on a waveform monitor or with a vectorscope-style display before releasing production hardware.

Keep the RGB input traces short and away from the composite output path, and place the device close to the 75-ohm termination point so the reverse-terminated composite output is not degraded by long board traces. Because the encoder integrates the delay line and auto-tuned filters, no external crystal or matched trap network is required, but the analog input routing still benefits from a solid ground plane under the SOIC pins. Provide local decoupling close to the supply pins and keep the composite output route away from switching regulators and clocked digital traces.

The most common mistakes in AD725AR designs are a mismatch between the intended standard and the configured encoder mode, incorrect termination on the composite output, and driving the RGB inputs from logic levels outside the TTL-compatible range. Confirm the NTSC versus PAL configuration in the manufacturer data sheet, terminate the composite output for 75-ohm reverse-terminated operation as specified, and check that the source logic (74HCT-family or 3 V CMOS) meets the input thresholds. Also verify the power-down state is used correctly in portable designs, where supply current below 1 microamp is expected.

زانیاری پابەندبوون

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
بێ قوڕقوشم
Unknown
بێ ھالۆجین
Unknown
کانزا ناکۆکەکان
Unknown

RoHS, REACH, lead-free and halogen-free status for the AD725 family are not stated in the retrieved manufacturer and distributor pages. Check the current Analog Devices product page and material declarations for the specific suffix before releasing to a regulated market. The device is not an automotive-qualified part, so AEC-Q100 does not apply.

داتا پشتڕاستکراوەتەوە لە: 2026-11-03 — داتا لەلایەن تیمی ئەندازیاری پێکھاتەکانی XAIPART پشتڕاستکراوەتەوە و ڕێکخراوە

گەڕانە پەیوەندیدارەکان

AD725AR AD725AR datasheet AD725AR datasheet pdf AD725AR pinout AD725AR vs AD725ARZ-R7 AD725AR drop-in replacement AD725AR equivalent AD725AR SOIC-16 video encoder AD725AR price AD725AR stock Analog Devices AD725AR RGB to NTSC PAL encoder IC AD725AR luma trap YTRAP AD725AR composite video output 75 ohm

پێکهاتە و زاراوە پەیوەندیدارەکان

Analog Devices AD725AR AD725 AD725ARZ-R7 AD725AR-REEL7 RGB to NTSC/PAL encoder video encoder IC composite video S-Video chrominance output luminance output luma trap (YTRAP) TTL logic levels 3 V CMOS logic auto-tuned filters integrated delay line color subcarrier 75 ohm reverse-terminated load power-down current below 1 microamp SOIC-16 SOIC package family surface mount cross-color artifact legacy CRT monitor interface broadcast video equipment
داواکاری نرخی خێرا RFQ
وردەکارییەکانی تەواو پڕ بکەرەوە — تیمی فرۆشتنی ئێمە لە ماوەی 24 کاتژمێردا وەڵام دەداتەوە
ژمارەی پارچە بەرهەمهێنەر پاکەت QTY نرخی ئامانج کۆی گشتی
✓
نرخەکە نێردرا!

لە ماوەی ٢٤ کاتژمێردا وەڵامی ئیمەیڵەکەت دەدەینەوە

1
داواکاری نرخ پێشکەشکرا
2
نرخپێدان وەرگیرا
3
داواکاری دانرا
4
پارەدان
5
نێردرا
6
گەیەنراوە
بینینی وردەکاریی داواکاری نرخ