AD746AQ - 13MHz Dual Precision BiFET Op Amp | Analog Devices
MPN: AD746AQ ✗ کۆتایی ژیانAD746AQ گشتی
A BiFET operational amplifier is a voltage-feedback amplifier whose input stage uses junction field-effect transistors. This input structure provides low input bias current and high input impedance while preserving the low offset voltage and common-mode characteristics needed for precision analog systems. In the broader hierarchy, the AD746 belongs to the operational amplifier, analog signal-conditioning IC, and power management and signal-chain semiconductor categories.
The AD746AQ contains two AD744 BiFET amplifiers on one monolithic die. Both channels therefore have closely matched DC and AC characteristics. Its 13 MHz gain-bandwidth supports signal bandwidth beyond the 0.01% settling criterion, while the internal compensation provides stable operation at gains of two or greater. A 500 ns settling time is especially useful when amplifying the outputs of 12-bit or 14-bit DACs and ADCs.
The low-noise input stage and 0.0001% THD make the amplifier suitable for demanding audio paths, instrumentation channels, and precision buffers. The matched channels can also implement differential, active-filter, line-driver, and current-to-voltage converter circuits. Inputs can operate around the supply rails when configured for the appropriate common-mode range, making the device useful in bipolar ±5 V, ±12 V, and ±15 V systems.
Typical uses include ADC input conditioning, DAC output buffering, active low-pass filters, audio preamplification, sensor signal amplification, and precision waveform-generation circuits. In a 12-bit DAC buffer, the AD746AQ combines sufficient bandwidth with fast settling to reduce code-transition error without relying on a complex external compensation network.
When laying out an AD746AQ circuit, keep the feedback components and signal traces short, provide adequate supply bypassing close to the device, and use clean ground returns. The ceramic package is suited to legacy precision and industrial equipment, but board availability and thermal performance should be checked before committing to a new design.
This page combines manufacturer performance characteristics with application-focused design guidance, package information, comparison data, and practical replacement considerations. It is intended to help engineers determine whether the AD746AQ’s precision, settling behavior, and low-noise BiFET architecture fit a specific analog signal chain.
جێگرەوەکانی جێگۆڕکێ بۆ AD746AQ — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ AD746AQ (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Amplifier Type, Settling Time.
AD746BQ
✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
AD746CQ
✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
AD746DQ
✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
AD746AQ زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان
| Amplifier Type | Dual precision BiFET operational amplifier |
| Number of Channels | 2 channels |
| Gain-Bandwidth Product | 13 MHz |
| Settling Time | 500 ns to 0.01% |
| Settling Test Step | 10 V step |
| Total Harmonic Distortion | 0.0001% |
| Internal Compensation | Unity-gain stable for gains of +2 or greater |
| Maximum Offset Voltage | 0.5 mV |
| Input Bias Current | 110 pA |
| ڤۆڵتیەی دابینکردن | 9 V to 36 V |
| Dual Supply Voltage | ±4.5 V to ±18 V |
| پاکێج | 8-pin ceramic DIP |
| Package Height | 0.300 inch |
| Package Pitch | 7.62 mm |
| جۆری دامەزراندن | Through-hole |
ڕێکخستنی پینی AD746AQ
| پین 1 | OUTA — Channel A output |
| پین 2 | INA− — Channel A inverting input |
| پین 3 | INA+ — Channel A non-inverting input |
| پین 4 | V− — Negative supply connection |
| پین 5 | INB+ — Channel B non-inverting input |
| پین 6 | INB− — Channel B inverting input |
| پین 7 | OUTB — Channel B output |
| پین 8 | V+ — Positive supply connection |
بەکارهێنانە باوەکان
AD746AQ گونجاوە بۆ 6 بەکارھێنانs: 12-bit and 14-bit DAC Output Buffering, ADC Front-End Signal Conditioning, Precision Active Filtering, Low-Distortion Audio Preamp, Current-to-Voltage Conversion, Precision Instrumentation and Sensor Amplification.
12-bit and 14-bit DAC Output Buffering
The AD746AQ fits DAC output buffering because its 13 MHz gain-bandwidth and 500 ns settling to 0.01% for a 10 V step limit the time required after a converter code transition. The dual BiFET channels provide low offset voltage and closely matched behavior on the same monolithic die. In a practical buffer, the amplifier operates in a conventional inverting or non-inverting configuration, with the feedback resistor and capacitor placed close to the device. The main trade-off is power dissipation in the ceramic DIP package, so output swing and load current should be checked against the thermal limits of the layout.
پێشنیارکراو
ADC Front-End Signal Conditioning
The AD746AQ can condition low-level signals ahead of a 12-bit or 14-bit ADC because its maximum offset voltage of 0.5 mV and low-noise BiFET input stage help preserve small differential signals. Its 13 MHz gain-bandwidth is ample for many moderate-speed acquisition channels, while 500 ns settling supports rapid code transitions. The amplifier should be placed close to the ADC input, with balanced feedback components and short traces that minimize parasitic pickup. Designers must verify that the selected gain, input range, and output swing meet the converter requirements without clipping.
پێشنیارکراو
Precision Active Filtering
The AD746AQ is suitable for active low-pass and band-pass filters where the matched dual channels help preserve symmetry between related paths. Its 13 MHz gain-bandwidth supports filter poles above the audio and low-frequency instrumentation range, while the BiFET inputs provide the high impedance normally desired for sensor and source stages. Component tolerances and op-amp gain-bandwidth behavior determine the achievable pole accuracy. Keep the input and feedback network compact, use matched resistor sets where channel balance matters, and verify stability at the lowest gain allowed by the internal compensation.
پێشنیارکراو
Low-Distortion Audio Preamp
The AD746AQ can serve as a low-distortion audio preamplifier because the Analog Devices datasheet specifies total harmonic distortion of 0.0001%. Its low-offset BiFET input stage is useful with high-impedance sources, and the two channels allow stereo or balanced signal handling with closely matched AC and DC characteristics. The implementation must remain within the input common-mode range and preserve output headroom. Low-distortion performance also depends on clean grounds, adequate supply bypassing, short feedback paths, and avoiding operation too close to either supply rail.
پێشنیارکراو
Current-to-Voltage Conversion
The AD746AQ is appropriate for precision current-to-voltage conversion because the low-offset BiFET input stage minimizes errors around the zero-current point, and the 500 ns settling supports higher-rate waveform systems than a general-purpose precision amplifier. The circuit typically uses a small sense resistor followed by an inverting amplifier, requiring careful attention to resistor accuracy and parasitic capacitance. The 13 MHz gain-bandwidth and 0.0001% THD help preserve waveform fidelity, while the ceramic DIP package makes the device easy to socket during legacy laboratory and instrumentation maintenance.
پێشنیارکراو
Precision Instrumentation and Sensor Amplification
The AD746AQ can amplify high-impedance sensor outputs where low input bias current and low offset voltage are more important than very low power. The BiFET input stage avoids the higher bias currents common to bipolar precision inputs, while the dual monolithic construction supports differential or multiplexed channels with closely matched characteristics. Its 13 MHz bandwidth handles many industrial measurement bands, but the design must compensate for sensor capacitance and protect inputs from transients. Feedback resistors should be selected for noise, bias-current error, and stability rather than resistance alone.
پێشنیارکراو
کورتەی بەرهەمە پێشنیارکراوەکان
داتای سەرچاوەی ئەندازیاری بۆ AD746AQ — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | AD746BQ | AD746CQ | AD746DQ |
|---|---|---|---|---|
| Package | 8-pin ceramic DIP | 8-pin ceramic DIP | 8-pin ceramic DIP | 8-pin ceramic DIP |
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Amplifier Architecture | Dual precision BiFET operational amplifier | Dual precision BiFET operational amplifier | Dual precision BiFET operational amplifier | Dual precision BiFET operational amplifier |
| Number of Channels | 2 | 2 | 2 | 2 |
| Gain-Bandwidth Product | 13 MHz | 13 MHz family value | 13 MHz family value | 13 MHz family value |
| Settling Time | 500 ns to 0.01% | 500 ns to 0.01% family value | 500 ns to 0.01% family value | 500 ns to 0.01% family value |
| Total Harmonic Distortion | 0.0001% | 0.0001% family value | 0.0001% family value | 0.0001% family value |
| Supply Voltage | 9 V to 36 V | 9 V to 36 V family value | 9 V to 36 V family value | 9 V to 36 V family value |
| Minimum Stable Gain | +2 | +2 family value | +2 family value | +2 family value |
| Special Feature | Close AC and DC channel matching | AD746B-grade offset-drift positioning | AD746C-grade DC-limit positioning | AD746D-grade offset-drift positioning |
جیاکەرەوە سەرەکییەکان
- Fast 0.01% settling in a dual precision BiFET package (بەراورد بەAD746BQ)
- Monolithic dual-channel matching for stereo and balanced paths (بەراورد بەAD746CQ)
- Legacy-compatible 8-pin ceramic DIP footprint (بەراورد بەAD746DQ)
- Low distortion for precision signal-chain use (بەراورد بەAD746CQ)
تێبینییەکانی دیزاین
Place each AD746AQ feedback network close to the relevant amplifier pins and route the inverting input as a short, quiet trace. The 13 MHz gain-bandwidth is high enough for stray board capacitance to alter closed-loop behavior in a precision circuit. Use short ground returns, avoid routing inputs beside switching nodes, and add a small isolation resistor close to the source when driving long cables or capacititive loads.
Place the supply-bypass capacitors immediately between pins 8 and 4, with the ground end connected to a low-impedance return plane. The AD746AQ operates from 9 V to 36 V, including ±4.5 V to ±18 V. Check that the chosen rail combination maintains the required input common-mode range and output swing. Adequate bypassing is especially important because the device’s fast settling behavior can expose supply-impedance problems.
Estimated: with a 15 V supply and a 12 V output at 10 mA load, the amplifier dissipates approximately (15 V − 12 V) × 0.01 A = 0.03 W. This estimate excludes internal quiescent dissipation and should be evaluated against the package and socket thermal limits. Keep ceramic-DIP sockets away from heat sources and ensure adequate airflow around legacy instrumentation boards.
Do not assume the AD746AQ is unity-gain stable: the internal compensation supports gains of two or greater. Also do not treat the ceramic package as a modern lead-free product identifier without checking its terminal finish and relevant compliance documentation. Before substituting another grade, compare offset voltage, drift, common-mode range, supply limits, temperature range, and channel matching against the original design requirements.
زانیاری پابەندبوون
The AD746AQ is a legacy precision operational amplifier, and no explicit environmental or automotive qualification statement is shown in the product material. Compliance fields remain unknown rather than being inferred from the package type.