ADM202JNZ - Dual RS-232 Transceiver | Analog Devices
MPN: ADM202JNZ ✓ چالاکADM202JNZ گشتی
An RS-232 transceiver is an interface circuit that converts logic-level signals between a digital system and a serial communications port. It belongs to the interface IC hierarchy, where physical-layer transceivers bridge a host controller or peripheral with the voltage, impedance, and signaling requirements of a wired communications standard. The ADM202JNZ integrates two line drivers and two receivers for bidirectional serial links using the TIA/EIA-232-E and V.28 specifications.
The principal features include two transmitters, two receivers, operation from a 4.5 V to 5.5 V supply, and a maximum transmission rate of 120 kbit/s. Its BiCMOS implementation has a stated supply current of 2.5 mA, while the receiver section tolerates inputs to ±30 V. The charge-pump architecture eliminates the need for a separate negative supply for bipolar RS-232 output signaling.
Fast driver slew rates support reliable transitions across the supported data rate, and the integrated level translation allows TTL or CMOS-compatible logic signals to connect directly to RS-232 lines. The device is suitable for industrial data acquisition, computer peripherals, test equipment, instrumentation, and embedded serial communications where a compact two-channel interface is required.
Design the charge-pump section with the minimum 0.1 µF capacitors specified by the manufacturer and place them close to the corresponding device pins. Check the receiver's ±30 V input tolerance against every connected signal source. Because this is a multidrop-unfriendly point-to-point interface, terminate and bias the bus according to the system-level RS-232 topology rather than treating it like an RS-485 multidrop bus.
This product page combines manufacturer specifications, packaging details, practical circuit guidance, same-package alternatives, and application-specific design considerations to help engineers evaluate the ADM202JNZ for new RS-232 interfaces and existing印制-board upgrades.
جێگرەوەکانی جێگۆڕکێ بۆ ADM202JNZ — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ ADM202JNZ (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Package, Mounting Type, Supply Voltage, Charge-Pump Capacitor Value, Data Rate.
ADM202EAN
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →MAX232EIN
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →MAX202E
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
HIN202CPZ
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
MAX232ECDR
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →ADM202JNZ تایبەتمەندییەکان
| Number of Drivers | 2 |
| Number of Receivers | 2 |
| Transceiver Configuration | 2 drivers and 2 receivers |
| Maximum Transmission Rate | 120 kbit/s |
| Supply Voltage Range | 4.5 V to 5.5 V |
| Nominal Supply Voltage | 5 V |
| Charge-Pump Capacitor Value | 0.1 µF |
| RS-232 Output Level | Approximately ±10 V |
| Receiver Input Voltage Tolerance | ±30 V |
| ئێستای دابینکردن | 2.5 mA |
| Interface Standard | TIA/EIA-232-E and V.28 |
| Technology | BiCMOS |
| پاکێج | 16-pin PDIP, 0.300 inch body width, 7.62 mm lead pitch |
| جۆری دامەزراندن | Through-hole |
| Shipping Package | Tube |
ڕێنمایی ڕێکخستنی پینی ADM202JNZ tube
ڕێکخستنی پین بۆ ADM202JNZ (پاکێجی tube). ژمارەدانی پین، فەنکشنەکان و نەخشەکانی پەیوەندی لە داتاشیتی بەرھەمھێنەردا پێناسە کراون. سەرنجی بدە بۆ شوێنپێی ورد و ڕێنمایییەکانی لەحیمکردن.
هیچ داتای وردی پینئاوت بەردەست نییە بۆ ADM202JNZ.
سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.
بەکارهێنانە باوەکان
ADM202JNZ گونجاوە بۆ 6 بەکارھێنانs: Industrial Data Acquisition, Computer Peripheral Interfaces, Test and Measurement Equipment, Embedded Serial Communication, Instrumentation and Laboratory Control, Point-to-Point Control Links.
Industrial Data Acquisition
The ADM202JNZ suits legacy industrial instruments that exchange commands and measurements through a two-channel RS-232 link. Two drivers and two receivers permit two full-duplex links when receive and transmit lines are paired, while the 120 kbit/s maximum rate covers many configuration and telemetry protocols. Operation from a single 4.5 V to 5.5 V supply simplifies internal power distribution, and the ±30 V receiver tolerance adds margin for exposed cables. The 16-pin PDIP footprint also supports repair and expansion boards that already use through-hole RS-232 components.
پێشنیارکراو
Computer Peripheral Interfaces
The ADM202JNZ can bridge a legacy computer or embedded controller to a serial peripheral requiring true RS-232 levels. The integrated charge pump supplies approximately ±10 V outputs without a separate negative supply rail, reducing board complexity compared with a discrete driver. A 120 kbit/s data rate accommodates peripheral configuration transfers and moderate diagnostic traffic. Its 2-driver/2-receiver organization supports simultaneous control and status paths, while the 16-pin PDIP package is convenient for prototype and repair-oriented equipment.
پێشنیارکراو
Test and Measurement Equipment
The ADM202JNZ is appropriate for bench instruments and portable test systems that need a robust point-to-point RS-232 command interface. Its receiver section tolerates voltages to ±30 V, which is useful when the connector may experience greater transients than the local logic rails. The 120 kbit/s rate supports measurement data and command streams while the low-power BiCMOS supply current of 2.5 mA helps manage thermal demand in compact instruments. A single 5 V supply also simplifies isolation and power-conversion design around the interface.
پێشنیارکراو
Embedded Serial Communication
The ADM202JNZ connects a controller-level UART to a system requiring RS-232 rather than TTL signaling. Its two receivers can monitor incoming data and handshake signals, and its two drivers can support transmit and control outputs. The 0.1 µF charge-pump capacitor option helps achieve a compact implementation, while the 16-pin PDIP package is well suited to through-hole industrial controllers and legacy equipment. Designers should verify UART logic levels, driver polarity, and the exact channel assignment against the application schematic.
پێشنیارکراو
Instrumentation and Laboratory Control
The ADM202JNZ is well suited to laboratory instruments, signal conditioners, and automated test fixtures using RS-232 control channels. Its fast 120 kbit/s capability supports responsive command traffic and moderate result transfers, while ±10 V output levels meet the bipolar signaling expected by RS-232 equipment. The on-chip charge pump avoids a separate negative analog supply in many single-board designs. Confirm grounding and cable length because RS-232 is a point-to-point interface, and ensure the ±30 V receiver rating is appropriate for the selected wiring environment.
پێشنیارکراو
Point-to-Point Control Links
The ADM202JNZ supports short, dedicated control links between two pieces of equipment where a multidrop bus is unnecessary. Two transmitter channels can carry command and status signals, while two receiver channels can support responses and hardware handshake signals. Its 4.5 V to 5.5 V supply range provides tolerance around a conventional 5 V rail, and the stated 2.5 mA supply current limits internal power demand. For cable routing and grounding, follow the RS-232 topology recommended for point-to-point links and validate the complete interface with the connected equipment.
پێشنیارکراو
کورتەی بەرهەمە پێشنیارکراوەکان
داتای سەرچاوەی ئەندازیاری بۆ ADM202JNZ — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | ADM202E | MAX232EIN | MAX202E | HIN202CPZ |
|---|---|---|---|---|---|
| Package | 16-pin PDIP | 16-pin PDIP | 16-pin PDIP | 16-pin PDIP | 16-pin PDIP |
| Brand | Analog Devices | Analog Devices | Maxim Integrated | Maxim Integrated | Hindustan Semiconductor |
جیاکەرەوە سەرەکییەکان
- Compact 0.1 µF charge-pump implementation (بەراورد بەMAX232EIN)
- Four-channel RS-232 interface in one package (بەراورد بەMAX202E)
- Wide receiver input tolerance (بەراورد بەHIN202CPZ)
تێبینییەکانی دیزاین
Place the charge-pump capacitors close to the ADM202JNZ charge-pump pins and follow the exact capacitor connection and grounding arrangement shown in the manufacturer datasheet. The device supports capacitors as small as 0.1 µF, but using the minimum value does not eliminate sensitivity to PCB leakage and high-frequency noise. Keep the charge-pump loop compact, provide an uninterrupted ground plane, and avoid routing sensitive analog signals through the area surrounding the switching charge-pump nodes.
Route each RS-232 driver output directly toward its connector and keep receiver inputs away from adjacent clock, switching-power, and high-current return paths. Although the receiver tolerates inputs to ±30 V, the rating is not a substitute for layout-based noise control. Use a solid ground reference, minimize loop area around the interface, and check connector pin assignments against the datasheet because incorrect driver or receiver pairing can prevent an apparently compatible replacement from operating correctly.
Do not treat ADM202JNZ as an RS-485 multidrop transceiver. It is a point-to-point RS-232 interface, and the system must account for RS-232 voltage polarity, grounding, cable limitations, and the connected equipment's logic expectations. Also verify that the UART and connected controller use compatible logic levels and that no external circuit conflicts with the on-chip charge-pump pins. Before replacing the device, compare every numbered 16-pin connection and the required external capacitor values.
زانیاری پابەندبوون
The manufacturer product page and listed technical summaries do not explicitly state the requested compliance classifications. Use the current Analog Devices product declaration or supporting material before making a compliance determination.