ADM207ANZ - 5/3 RS-232 Transceiver | Analog Devices
MPN: ADM207ANZ ✓ چالاکADM207ANZ گشتی
An RS-232 transceiver is an interface integrated circuit that combines line drivers and line receivers for serial data communication. The drivers convert logic-level signals into RS-232-compatible levels, while the receivers convert incoming bipolar signals into CMOS logic levels. The ADM2xx family is intended for data links where ±12 V is unavailable, making the ADM207ANZ suitable for industrial control, instrumentation, point-of-sale equipment, and legacy peripheral interfaces.
The ADM207ANZ provides five transmit channels and three receive channels, allowing several RS-232 signals to share one interface component. Its CMOS implementation operates from +5 V and uses 0.1 µF capacitors for the internal charge-pump circuit. A maximum data rate of 200 kbps supports moderate-speed serial links, while the five-driver configuration can serve clock, control, and data lines in multidrop-style point-to-point equipment arrangements.
The 24-pin PDIP package provides through-hole mounting and generous spacing between pins, which can simplify inspection and prototype rework. Because it is a single-supply RS-232 interface, the ADM207ANZ is particularly useful when the host logic operates from 5 V and the connected equipment implements the physical RS-232 voltage interface rather than a differential RS-485 or RS-422 bus. The receiver and driver arrangement should be checked against the required signal direction of each cable.
Typical applications include industrial serial controllers, laboratory instruments, barcode and point-of-sale terminals, embedded service interfaces, and communication links between older RS-232 peripherals and modern control boards. The five transmit channels are useful when a system requires bidirectional data plus hardware-control lines without allocating a separate driver IC for every signal.
The principal design consideration is external capacitor placement. Place the two 0.1 µF charge-pump capacitors close to their specified pins and follow the manufacturer’s polarity and connection diagram. Confirm that the selected cable uses RS-232 signal and ground conductors correctly, and do not expose the interface to voltages outside the device’s stated operating limits.
This page organizes the ADM207ANZ’s interface capability, application fit, package details, verified commercial sources, and replacement limitations into a concise engineering reference. Because drop-in substitutions must preserve the 24-pin PDIP footprint and channel functions, any replacement should be checked against the manufacturer pinout and electrical tables before PCB release.
جێگرەوەکانی جێگۆڕکێ بۆ ADM207ANZ — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ ADM207ANZ (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Maximum Data Rate, Product Type.
هیچ جێگرەوەی ڕاستەوخۆ بۆ ئەم بەرهەمە بەردەست نییە.
داوای جێگرەوەکان بکەADM207ANZ تایبەتمەندییەکان
| Product Type | RS-232 transceiver |
| Number of Drivers | 5 |
| Number of Receivers | 3 |
| Maximum Data Rate | 200 kbps |
| ڤۆڵتیەی دابینکردن | +5 V |
| Charge-Pump Capacitor | 0.1 µF |
| Logic Family | CMOS |
| Interface Standard | EIA-232-E and CCITT V.28 |
| پاکێج | 24-pin PDIP |
| جۆری دامەزراندن | Through-hole |
| Lead Pitch | 7.62 mm |
| Packaging | Tube |
ڕێنمایی ڕێکخستنی پینی ADM207ANZ 24-pin pdip
ڕێکخستنی پین بۆ ADM207ANZ (پاکێجی 24-pin pdip). ژمارەدانی پین، فەنکشنەکان و نەخشەکانی پەیوەندی لە داتاشیتی بەرھەمھێنەردا پێناسە کراون. سەرنجی بدە بۆ شوێنپێی ورد و ڕێنمایییەکانی لەحیمکردن.
هیچ داتای وردی پینئاوت بەردەست نییە بۆ ADM207ANZ.
سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.
بەکارهێنانە باوەکان
ADM207ANZ گونجاوە بۆ 6 بەکارھێنانs: Industrial Serial Controller, Point-of-Sale Terminal, Laboratory Instrumentation, Embedded Service Interface, Barcode and Data Collection Equipment, Legacy Peripheral Connectivity.
Industrial Serial Controller
The ADM207ANZ fits industrial controllers that exchange several RS-232 signals with test equipment, service equipment, or peripheral controllers. Its five drivers support outbound data, handshake, and equipment-control lines, while three receivers provide incoming status or acknowledgement channels. Operation from a single +5 V supply simplifies the interface when the controller does not have a ±12 V rail, and the 200 kbps maximum signaling rate supports moderate-speed protocols. Through-hole PDIP construction is useful for industrial control boards designed around accessible solder joints. Designers should allocate the charge-pump capacitors close to the device and implement suitable protection for cables connected outside the enclosure.
پێشنیارکراو
Point-of-Sale Terminal
Point-of-sale terminals can use the ADM207ANZ when a single serial port must support transaction data, printer commands, status signals, and control handshakes. Five transmit channels provide more line capacity than a basic one-driver, one-receiver interface, and three receive channels accommodate acknowledgements or device status. The +5 V CMOS operation suits embedded systems powered from 5 V, while the 200 kbps rate is appropriate for many legacy point-of-sale protocols. The PDIP package is also practical for equipment assembled with through-hole connectors. Cable routing and signal-ground handling remain important because long or poorly terminated RS-232 cables can reduce reliability despite the device’s integrated protection characteristics.
پێشنیارکراو
Laboratory Instrumentation
The ADM207ANZ is appropriate for laboratory instruments that expose a legacy RS-232 service or control port. Instrument commands and acknowledgments can occupy separate transmit and receive channels, while additional drivers handle hardware-control lines such as measurement trigger, remote enable, or reset. The five-driver and three-receiver organization reduces the number of interface packages needed compared with discrete driver and receiver circuits. Its single +5 V operation also helps when the instrument’s analog and digital sections already use a 5 V rail. At the 200 kbps maximum, the link is suitable for many short-distance instrument-control protocols. Engineers should use a suitable transceiver level for long cables and consider galvanic isolation where ground potential differences are possible.
پێشنیارکراو
Embedded Service Interface
Embedded products often retain an RS-232 port for configuration, diagnostics, firmware recovery, or connection to legacy accessories. The ADM207ANZ provides enough channel count to implement a bidirectional data link plus handshake and status signals without occupying several connector positions. Because it runs from +5 V, the interface can be placed near a 5 V control domain without a separate high-voltage supply. The 200 kbps capability is more than adequate for configuration consoles and short diagnostic sessions. Its through-hole PDIP package suits products with a permanent PCB and accessible connector pads. Keep the interface disabled until the host firmware initializes the relevant pins, and route the cable connector ground return close to the signal ground to reduce common-mode effects.
پێشنیارکراو
Barcode and Data Collection Equipment
Barcode readers, scales, receipt printers, and magnetic-stripe peripherals in older retail systems commonly use multi-line RS-232 connections. The ADM207ANZ can connect several outbound control and data signals while receiving acknowledgment and status lines from the peripheral cluster. Its +5 V operation aligns with many embedded controller boards, and the 200 kbps rate supports typical short-distance scanner and printer traffic. The 24-pin PDIP package is straightforward to assemble on through-hole industrial daughterboards and simplifies servicing. Designers should match the driver and receiver assignments to the actual cable, because a device that physically fits the connector may still require different signal direction or handshake polarity. Shielded or reduced-twist RS-232 cable is preferable for factory environments with electrical noise.
پێشنیارکراو
Legacy Peripheral Connectivity
The ADM207ANZ can modernize a controller board that must connect to older RS-232 peripherals while the controller itself operates from a 5 V CMOS supply. Five drivers allow dedicated lines for transmit data and multiple control functions, and three receivers permit concurrent return channels for acknowledgments, status, and remote signals. The 200 kbps maximum rate is suitable for many legacy peripheral protocols that operate at substantially lower baud rates. A PDIP package eases migration into an existing through-hole design without adding an external ±12 V supply. Before redesigning a modern interface around this part, verify that the legacy equipment expects RS-232 bipolar levels rather than RS-422 or RS-485 differential signaling, because those electrical standards are not interchangeable.
پێشنیارکراو
کورتەی بەرهەمە پێشنیارکراوەکان
داتای سەرچاوەی ئەندازیاری بۆ ADM207ANZ — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە |
|---|---|
| Product Type | RS-232 transceiver |
| Brand | Analog Devices |
| Package | 24-pin PDIP |
| Number of Drivers | 5 |
| Number of Receivers | 3 |
| Maximum Data Rate | 200 kbps |
| Supply Voltage | +5 V |
| Charge-Pump Capacitor | 0.1 µF |
| Logic Family | CMOS |
| Interface Standard | EIA-232-E and CCITT V.28 |
جیاکەرەوە سەرەکییەکان
- Five transmitters support multi-line control interfaces (بەراورد بەADM207AN)
- Single +5 V CMOS implementation (بەراورد بەADM207ARZ)
- Through-hole package supports accessible assembly (بەراورد بەADM207ARZ)
تێبینییەکانی دیزاین
Place the two 0.1 µF charge-pump capacitors close to the ADM207ANZ pins identified in the manufacturer application diagram. Keep the associated traces short and follow the specified capacitor type and polarity. A long charge-pump loop can increase supply and ground current transients, while routing the drivers and receivers away from sensitive analog sections helps prevent coupling between interface transitions and measurement circuitry.
Assign each connector signal deliberately to a transmitter or receiver and confirm the logic polarity against the attached equipment. A physically compatible RS-232 connector does not guarantee electrical compatibility because some devices use DTE signal assignments while others use DCE assignments. Preserve the connector ground return, avoid routing the RS-232 interface next to switching-power nodes, and use a common signal-ground reference where permitted by the system architecture.
Do not substitute ADM207ARZ for ADM207ANZ on the existing PCB: ADM207ARZ uses a 24-pin SSOP footprint, while ADM207ANZ uses a 24-pin PDIP footprint. The two package styles are not pin-compatible without a layout change. Likewise, confirm that any proposed related ADM207 ordering code has the same temperature grade, pin definitions, charge-pump arrangement, and mechanical suffix before releasing it as a drop-in alternative.
Treat the RS-232 connector as an external cable interface and plan for conducted-noise entry even when the ADM207ANZ is used with a short internal harness. Use the shortest practical ground return, secure the cable shield according to the enclosure strategy, and add series impedance at externally accessible lines when the application permits. Verify communication margin at the intended baud rate and cable length rather than relying solely on the advertised 200 kbps capability.
زانیاری پابەندبوون
The available product and distributor information does not explicitly state the requested compliance status. EIA-232-E and CCITT V.28 are interface specifications rather than material-compliance declarations.