Analog Devices

ADM238LJN - 4/4 120kbps RS-232 IC | Analog Devices

MPN: ADM238LJN ✗ کۆتایی ژیان
5 V Vdss 1 A Id EIA-232-E and V.28 Rds(on) 24-pin PDIP Package
MOQ: 1 |

ADM238LJN گشتی

Analog Devices ADM238LJN is a 4/4 full-duplex RS-232 line-driver and receiver interface IC with a 120 kB/s data rate, single 5 V power supply, and 24-pin PDIP package. It provides four transmit drivers and four receive channels, producing approximately 9 V output swing from the 5 V supply through on-board DC-DC converters. The device targets EIA-232-E and V.28 serial interfaces where a ±12 V supply is unavailable.

An RS-232 transceiver is an interface IC that combines differential digital signaling levels with a single logic-level supply. In the broader electronics hierarchy, the ADM238LJN belongs to the interface IC class, specifically the RS-232 transceiver family. Its integrated DC-DC converter generates the higher voltage needed for RS-232 driver outputs while the receiver circuitry restores serial data to compatible logic levels.

The ADM238LJN's principal features include a 120 kB/s data rate, 9 V output swing, 1 F charge-pump capacitors, a low-power shutdown function, and receivers that remain active during shutdown. A 1 A receiver output capability supports the stated receiver-load condition, while the 30 V receiver-input rating provides additional tolerance for exposed serial lines. These characteristics simplify legacy and industrial RS-232 connections without requiring a separate negative supply rail.

The device is intended for EIA-232-E and V.28 communications interfaces, including industrial equipment, instrumentation, data-acquisition systems, service consoles, and legacy peripheral connections. Four full-duplex channels allow one connector to carry four data paths in each direction. Its 120 kB/s rate is suitable for conventional serial control and communication links rather than high-speed differential or Ethernet protocols.

PCB design must preserve the RS-232 interface requirement for a single 5 V supply even though driver outputs swing to approximately 9 V. Place the specified 1 F capacitors close to the charge-pump pins, route driver outputs away from sensitive receiver and logic traces, and maintain the 24-pin PDIP footprint without changing the land pattern. Review the receiver input rating before connecting externally accessible lines.

The ADM238LJN is listed as obsolete, so availability may be limited. This page synthesizes the device specifications, sourcing guidance, drop-in comparison, application guidance, and design considerations that engineers need when supporting an installed ADM238LJN design.

جێگرەوەکانی جێگۆڕکێ بۆ ADM238LJN — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.

جۆرەکان لەم زنجیرەیەدا

مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ ADM238LJN (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Product Type, Maximum Data Rate, Number of Receivers, Number of Drivers, Package.

Analog Devices
Product Type: 0.1 µF, +5 V powered CMOS RS-232 drivers/receivers
Maximum Data Rate: 200 kbps
Number of Receivers: 3
بەراوردکردن لەگەڵ ADM238LJN →
Analog Devices
Product Type: RS-232 driver/receiver transceiver IC
Number of Receivers: 3 receivers
Number of Drivers: 4 drivers
بەراوردکردن لەگەڵ ADM238LJN →
Analog Devices
Product Type: 4/4 full-duplex RS-232 transceiver
Maximum Data Rate: 120 kB/s
Number of Receivers: 4
بەراوردکردن لەگەڵ ADM238LJN →
Analog Devices
Product Type: RS-232 transceiver
Maximum Data Rate: 100 k BPS
بەراوردکردن لەگەڵ ADM238LJN →

HIN238CP

✅ جێگرەوەی ڕاستەوخۆ
📦 24-pin PDIP
Same 4/4 120 kB/s RS-232 interface and 24-pin PDIP format; stated headline channel count and data rate differ by 0%.

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

ADM238LJN تایبەتمەندییەکان

Product Type 4/4 full-duplex RS-232 transceiver
Power Supply 5 V
Number of Drivers 4
Number of Receivers 4
Maximum Data Rate 120 kB/s
Driver Output Swing 9 V
Charge-Pump Capacitor 1 F
Low-Power Shutdown Yes
Receiver Output Current 1 A
Receivers Active During Shutdown Yes
Maximum Receiver Input Voltage 30 V
Interface Standards EIA-232-E and V.28
پاکێج 24-pin PDIP
Package Lead Spacing 7.62 mm (0.300 in)
جۆری دامەزراندن Through-hole
Product Status Obsolete

ڕێنمایی ڕێکخستنی پینی ADM238LJN 7.62 mm (0.300 in)

ڕێکخستنی پین بۆ ADM238LJN (پاکێجی 7.62 mm (0.300 in)). ژمارەدانی پین، فەنکشنەکان و نەخشەکانی پەیوەندی لە داتاشیتی بەرھەمھێنەردا پێناسە کراون. سەرنجی بدە بۆ شوێنپێی ورد و ڕێنمایییەکانی لەحیمکردن.

نەخشەی پینئاوتی پاکێجی 7.62 mm (0.300 in) بۆ ADM238LJN

هیچ داتای وردی پینئاوت بەردەست نییە بۆ ADM238LJN.

سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.

بەکارهێنانە باوەکان

ADM238LJN گونجاوە بۆ 6 بەکارھێنانs: Industrial Instrument RS-232 Port, Legacy Data-Acquisition Equipment, Service and Diagnostic Console, Automated Test Equipment, Embedded Serial Controller, Legacy Peripheral Multiport Connection.

🏭

Industrial Instrument RS-232 Port

The ADM238LJN fits industrial instruments that expose a four-channel RS-232 interface but cannot provide a separate ±12 V supply. Its four drivers and four receivers support full-duplex command, status, measurement, and control paths, while the integrated DC-DC converters produce approximately 9 V output swing from one 5 V rail. The 120 kB/s rate is appropriate for conventional EIA-232-E and V.28 equipment links. Place the specified 1 F charge-pump capacitors close to their pins and route the four transmit outputs away from receive and low-level signal traces to minimize data errors.

📟

Legacy Data-Acquisition Equipment

The ADM238LJN is useful in data-acquisition equipment that retains a four-channel RS-232 connection to a host, sensor controller, or service computer. A 120 kB/s maximum rate supports command transfer and periodic measurement updates without requiring a high-speed communications standard. The four full-duplex channels can reduce connector usage by supporting several unidirectional data paths simultaneously. Because the receiver input can withstand 30 V and the driver generates approximately 9 V from a 5 V supply, the interface simplifies system power design while retaining the voltage behavior expected by RS-232 equipment.

🔧

Service and Diagnostic Console

The ADM238LJN can support service consoles that need multiple RS-232 paths for configuration, status, logs, and diagnostic commands. Its four transmit and four receive channels provide more integration than a single-channel transceiver, while the 120 kB/s rate suits manual or supervisory communication. The single 5 V supply is particularly useful where the equipment does not generate ±12 V. Keep the charge-pump section compact and observe the receiver-input rating when connecting cables, because externally accessible serial lines can carry transients beyond ordinary logic levels.

🖥️

Automated Test Equipment

The ADM238LJN is appropriate for automated test equipment with legacy RS-232 control interfaces. Four full-duplex channels can carry separate commands, status signals, fixture data, and error reports at rates up to 120 kB/s. Operating from one 5 V rail simplifies the interface section of compact test systems, while the on-board converters provide approximately 9 V driver output swing. For reliable fixture communication, maintain short return paths, connect the interface ground correctly, and isolate transmit outputs from sensitive measurement circuitry to prevent switching and charge-pump coupling.

🧩

Embedded Serial Controller

The ADM238LJN can bridge an embedded controller to four RS-232 channels without requiring a separate negative supply rail. Its 120 kB/s data rate is suitable for command, response, and supervisory links, and the receiver output current rating of 1 A covers the stated receiver-load condition. The shutdown function allows power reduction when transmit activity is unnecessary, while active receivers can continue monitoring. Firmware designers should confirm that each unused driver and receiver pin is terminated exactly as shown in the manufacturer guidance and that the external capacitors meet the specified requirements.

🖨️

Legacy Peripheral Multiport Connection

The ADM238LJN addresses legacy peripherals that provide several RS-232 ports but have limited board space. Four transmit and four receive channels fit into one 24-pin PDIP, allowing separate connections for control, status, and data without several single-channel transceivers. The 5 V-only supply architecture reduces power-supply complexity, and the approximately 9 V driver swing meets the expected RS-232 output requirement. During layout, reserve adequate clearance between external connector fields and logic circuitry, keep ground returns continuous, and follow the documented capacitor placement to avoid charge-pump noise affecting received data.

What is the ADM238LJN?
The ADM238LJN is a 4/4 full-duplex RS-232 transceiver IC from Analog Devices. It combines four line drivers with four receiver channels, operates from a single 5 V supply, supports data rates up to 120 kB/s, and is packaged in a 24-pin PDIP. According to the manufacturer datasheet, its on-board DC-DC converters produce approximately 9 V output swing without requiring a separate ±12 V supply.
What is the operating voltage of ADM238LJN?
The ADM238LJN operates from a single 5 V power supply. Its integrated DC-DC conversion circuitry supplies the voltage required by the RS-232 drivers, allowing approximately 9 V output swing without an external negative supply. The manufacturer datasheet identifies the device as a 5 V-powered CMOS RS-232 driver and receiver, with 1 F charge-pump capacitors used in the converter circuit.
How fast is the ADM238LJN RS-232 transceiver?
The ADM238LJN supports a maximum data rate of 120 kB/s. This rate is appropriate for conventional EIA-232-E and V.28 serial control, diagnostic, and data-acquisition links. The same datasheet describes the part as a 4/4 RS-232 transceiver, meaning that all four transmitter and receiver channels are implemented in the 24-pin PDIP package.
Where can I download the ADM238LJN datasheet PDF?
The ADM238LJN datasheet PDF is available from the Analog Devices document listing linked on this page. The manufacturer documentation describes the device as a 5 V-powered CMOS RS-232 driver and receiver, including its EIA-232-E and V.28 compliance, 120 kB/s data rate, 9 V output swing, shutdown behavior, and charge-pump capacitor requirements. Use the pin-description and electrical-characteristics tables when designing or supporting the interface.
Where can I find the ADM238LJN pinout?
The ADM238LJN pinout is defined in the pin-description table of the manufacturer datasheet. The device uses a 24-pin PDIP package, so assignments should be transferred by pin number rather than inferred from connector position. Pay particular attention to supply, ground, charge-pump capacitor, driver-output, and receiver-input pins when checking an existing PCB.
Does ADM238LJN need a negative 12 V supply?
No. The ADM238LJN requires only a single 5 V supply because it includes on-board DC-DC converters. Those converters support approximately 9 V RS-232 driver output swing. This simplifies the interface compared with a traditional RS-232 implementation that uses approximately ±12 V rails, while the 1 F charge-pump capacitors remain required for proper converter operation.
What is the ADM238LJN vs ADM236LJN difference?
The principal channel-count difference is that the ADM238LJN is a 4/4 transceiver, while the ADM236LJN is a 4/3 device. Both are associated with 24-pin PDIP RS-232 interfaces and 120 kB/s operation. Because the receiver-channel count differs, the ADM236LJN is not a pin-for-pin functional replacement when all four receive channels are required; the ADM238LJN should remain the selection for four drivers and four receivers.
Is the HIN238CP a drop-in replacement for ADM238LJN?
The HIN238CP is the closest identified cross-brand drop-in candidate because it is presented in comparison data against the ADM238LJN and shares the same 4/4 RS-232 interface class and 24-pin PDIP format. Confirm pin numbering, shutdown behavior, charge-pump capacitor requirements, and electrical limits against both manufacturer datasheets before production use. The cross-reference designation does not remove the need for a board-level qualification review.
What is the best drop-in replacement for ADM238LJN?
The HIN238CP is the strongest identified drop-in candidate for an ADM238LJN replacement because it is a 4/4, 5 V RS-232 transceiver in the corresponding 24-pin PDIP format. One substitution candidate is available from the cross-reference results, so there is not enough supported diversity to present five independent drop-in options. Verify every pin, the 120 kB/s operating limit, shutdown behavior, and external capacitor arrangement before substitution.
When should I choose ADM238LJN over a lower-channel RS-232 transceiver?
Choose the ADM238LJN when the interface requires four transmit channels and four receive channels in one 24-pin PDIP device. A lower-channel part may be adequate for point-to-point links, but it can reduce channel count or require additional circuitry. The ADM238LJN is especially relevant when maintaining an obsolete installed design because its 120 kB/s rate and 5 V architecture match the documented RS-232 function.
Is ADM238LJN suitable for industrial equipment?
The ADM238LJN is suitable for legacy RS-232 equipment and industrial service interfaces that operate at 120 kB/s or less. Its four full-duplex channels, single 5 V supply, and approximately 9 V driver swing support compact transceiver implementations. Because the device is listed as obsolete, a new long-life industrial design should also evaluate a currently supported interface IC after checking protocol, isolation, and environmental requirements.
What is the lifecycle status of ADM238LJN?
The ADM238LJN is listed as obsolete. Obsolete status means new designs should not assume routine long-term production, while installed equipment may still require repair or replication. For an existing board, verify exact package, pinout, and capacitor requirements before ordering a cross-brand substitute. Use the Request a Quote form on this page for current sourcing and lead-time information.
How should the ADM238LJN charge-pump capacitors be placed?
Place the required 1 F capacitors close to their designated pins and minimize loop area around the charge-pump circuit. Keep the high-voltage driver routes away from receiver inputs and sensitive logic traces to reduce coupling and data errors. The manufacturer application guidance should be followed for capacitor type, voltage rating, placement, and trace geometry, especially when replacing the obsolete original in an existing assembly.
Can ADM238LJN receivers operate while the device is shut down?
Yes. The manufacturer datasheet states that the ADM238LJN receivers remain active in shutdown. This feature can allow a receive path to remain functional while reducing power dissipation in the driver and converter sections. It is useful when a system must monitor a connection while suppressing transmit activity, provided the external interface state and supply sequencing are designed consistently.
Where can I buy ADM238LJN and check its price and lead time?
Use the Request a Quote form on this page to request the current ADM238LJN price, stock position, minimum order quantity, and lead time. The ADM238LJN is listed as obsolete, so availability may depend on remaining inventory or qualified sourcing channels. When requesting a quote, include the required 24-pin PDIP package and any approved substitute requirements to avoid accidental package mismatches.
What are the key specifications of ADM238LJN that engineers should know?
The key ADM238LJN specifications are a single 5 V supply, four drivers, four receivers, a 120 kB/s maximum data rate, approximately 9 V output swing, 1 F charge-pump capacitors, low-power shutdown, active shutdown receivers, a 30 V receiver-input rating, and a 24-pin PDIP package. According to the manufacturer datasheet, the device meets EIA-232-E and V.28 interface requirements, making it a four-channel CMOS RS-232 transceiver.

داتای سەرچاوەی ئەندازیاری بۆ ADM238LJN — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.

ڕێنمایی هەڵبژاردن

Choose the ADM238LJN when maintaining a design that requires four RS-232 transmit channels, four receive channels, a 120 kB/s interface, and operation from one 5 V supply. Its integrated DC-DC conversion provides approximately 9 V output swing, while shutdown operation can reduce power and keep receivers active. The HIN238CP is the closest supported drop-in candidate for board replacement, but verify its pinout, capacitor arrangement, shutdown behavior, and electrical limits before use. Do not select a 4/3 or 3/3 transceiver when every receiver path is required. Because the ADM238LJN is obsolete, use it primarily for repair, replication, and continuity of an existing qualified design; new long-life products should evaluate a currently supported RS-232 interface with appropriate isolation and environmental requirements.

بەراوردکردن لەگەڵ جێگرەوەکان

پارامەتر ئەم بەرهەمە HIN238CP
Brand Analog Devices Maxim Integrated
Package 24-pin PDIP 24-pin PDIP - same package
Transceiver Configuration 4 drivers / 4 receivers 4 drivers / 4 receivers
Maximum Data Rate 120 kB/s 120 kB/s
Power Supply 5 V 5 V

جیاکەرەوە سەرەکییەکان

  • Four full-duplex RS-232 channels in one device (بەراورد بەADM236LJN)
  • Single-supply RS-232 operation (بەراورد بەTraditional discrete RS-232 interface)
  • High channel count for a 24-pin package (بەراورد بەMAX3232IPW)

تێبینییەکانی دیزاین

Place the two 1 F charge-pump capacitors as close as practical to their designated pins, using short ground returns and minimal loop area. The generated voltage feeds the RS-232 drivers, so long or shared return paths can increase radiated noise and susceptibility to data errors. Follow the manufacturer layout artwork rather than estimating capacitor positions from a generic RS-232 reference design.

Keep the four transmit outputs away from receiver inputs, references, and sensitive measurement traces, and provide a continuous interface-ground path. The driver produces approximately 9 V swing even though the logic supply is 5 V, so a common assumption that all nearby signals remain at logic voltage is unsafe. Use the 30 V receiver-input rating as a maximum interface condition rather than as a design target.

Do not substitute a 3/3 or 4/3 RS-232 transceiver for the ADM238LJN when all four receive channels are required. Also verify the exact PDIP pinout and the external 1 F capacitor arrangement before replacing an obsolete board. A matching package count does not prove that shutdown polarity, charge-pump pins, receiver enable behavior, and logic levels are interchangeable.

زانیاری پابەندبوون

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
بێ قوڕقوشم
Unknown
بێ ھالۆجین
Unknown
کانزا ناکۆکەکان
Unknown

The ADM238LJN is an interface IC rather than an automotive-qualified device. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status were not stated in the cited product information.

داتا پشتڕاستکراوەتەوە لە: 2026-11-03 — داتا لەلایەن تیمی ئەندازیاری پێکھاتەکانی XAIPART پشتڕاستکراوەتەوە و ڕێکخراوە

گەڕانە پەیوەندیدارەکان

ADM238LJN datasheet ADM238LJN datasheet pdf ADM238LJN pinout ADM238LJN specifications ADM238LJN equivalent ADM238LJN replacement ADM238LJN cross reference ADM238LJN vs HIN238CP ADM238LJN 24-PDIP ADM238LJN 120 kB/s ADM238LJN RS-232 transceiver ADM238LJN price

پێکهاتە و زاراوە پەیوەندیدارەکان

Analog Devices ADM238LJN HIN238CP ADM236LJN RS-232 RS-232 transceiver interface IC line driver line receiver full duplex CMOS EIA-232-E V.28 DC-DC converter charge-pump capacitor low-power shutdown 5 V power supply 9 V output swing 120 kB/s data rate 24-pin PDIP through-hole package 30 V receiver input industrial instrumentation legacy data acquisition
داواکاری نرخی خێرا RFQ
وردەکارییەکانی تەواو پڕ بکەرەوە — تیمی فرۆشتنی ئێمە لە ماوەی 24 کاتژمێردا وەڵام دەداتەوە
ژمارەی پارچە بەرهەمهێنەر پاکەت QTY نرخی ئامانج کۆی گشتی
✓
نرخەکە نێردرا!

لە ماوەی ٢٤ کاتژمێردا وەڵامی ئیمەیڵەکەت دەدەینەوە

1
داواکاری نرخ پێشکەشکرا
2
نرخپێدان وەرگیرا
3
داواکاری دانرا
4
پارەدان
5
نێردرا
6
گەیەنراوە
بینینی وردەکاریی داواکاری نرخ