Analog Devices

ADM242ARZ - 200 kB/s RS-232 Transceiver | Analog Devices

MPN: ADM242ARZ ✓ چالاک
5 V Vdss 18-lead SOIC Package
MOQ: 1 |

ADM242ARZ گشتی

The Analog Devices ADM242ARZ is a high-speed RS-232 line transceiver with two drivers and two receivers, supporting transmission rates up to 200 kB/s from a single 5 V supply. The device uses 0.1 µF charge-pump capacitors to develop bipolar RS-232 levels and is packaged in an 18-lead SOIC for surface-mount assembly. It also includes shutdown and enable control functions for power-managed serial interfaces.

An RS-232 transceiver is an interface IC that combines line drivers and line receivers into a complete logic-side-to-serial-port link. Within the hierarchy of interface ICs, RS-232 transceivers convert standard logic-level signals into differential-voltage, bipolar signaling and then recover the incoming serial data. The ADM242 family is designed for equipment requiring higher serial throughput than conventional RS-232 transceivers while retaining the familiar single-supply implementation.

Key features include a maximum transmission rate of 200 kB/s, operation from one 5 V supply, two integrated drivers, and two integrated receivers. The on-chip charge pump requires only 0.1 µF external capacitors. According to the Analog Devices ADM242 product information, the circuit meets EIA-232-E and V.28 specifications and supports full-duplex RS-232 communication. Shutdown and enable controls add flexibility for systems that need to reduce supply current or manage peripheral power states.

The charge-pump architecture raises the low-side driver output above the normal logic supply range, enabling approximately 9 V output swing with a 5 V supply. Receiver input levels extend to 30 V, supporting the wider voltage range associated with RS-232 ports. Because these are bipolar line signals, designers should protect exposed serial interfaces against surge, ESD, and accidental overvoltage conditions rather than treating every connector-side node as ordinary logic.

Typical applications include industrial serial consoles, data-acquisition equipment, instrumentation, communications adapters, and embedded systems that exchange RS-232 data over cable runs. The 200 kB/s rate is suitable for moderate-speed control and diagnostic traffic, including configuration transfers and periodic status reporting. Systems requiring continuous data flow, very low power, or longer unrepeated distances should compare the interface requirements against the exact RS-232 timing, noise, and cable-loss limits.

The principal design consideration is capacitor placement. Position the 0.1 µF charge-pump capacitors close to their designated pins and route the associated current paths carefully to minimize switching disturbance on sensitive circuitry. Place input and output protection components where cable-side connections enter the board, and confirm that the exposed metal package area has adequate copper for thermal dissipation and, where required, an exposed-pad connection.

This page combines the manufacturer’s interface specifications, packaging information, practical application guidance, and a documented drop-in comparison to support faster design review and sourcing decisions. It also identifies where detailed pin assignments and procurement conditions must be checked directly against the Analog Devices datasheet and the Request a Quote form.

جێگرەوەکانی جێگۆڕکێ بۆ ADM242ARZ — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.

جۆرەکان لەم زنجیرەیەدا

مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ ADM242ARZ (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Package, Mounting Type, Supply Voltage, Product Type.

Analog Devices
Package: 18-pin PDIP
Mounting Type: Through-hole
Product Type: RS-232 line transceiver
بەراوردکردن لەگەڵ ADM242ARZ →
Analog Devices
Package: SOIC-18
Supply Voltage: 4.5 V to 5.5 V
Product Type: CMOS RS-232 transceiver
بەراوردکردن لەگەڵ ADM242ARZ →

ADM242AR

✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە
Analog Devices
📦 18-lead SOIC
CMOS RS-232 transceiver · 2 · 2 · 200 kbps · 4.5 V to 5.5 V · 5 V · 0.1 µF · SOIC-18

پەیوەندی بۆ نرخ

بینینی داتاشیت →

ADM242ARZ تایبەتمەندییەکان

Transmission Rate 200 kB/s
ڤۆڵتیەی دابینکردن 5 V
Charge-Pump Capacitor Value 0.1 µF
Number of Drivers 2
Number of Receivers 2
Driver Output Swing Approximately 9 V
Receiver Input Levels 30 V
Duplex Mode Full duplex
Shutdown Control Yes
Enable Control Yes
RS-232 Compliance EIA-232-E and V.28
پاکێج 18-lead SOIC
جۆری دامەزراندن Surface mount
ژمارەی پین 18
Document Revision Rev. C

ڕێنمایی ڕێکخستنی پینی ADM242ARZ 18-lead soic

ڕێکخستنی پین بۆ ADM242ARZ (پاکێجی 18-lead soic). ژمارەدانی پین، فەنکشنەکان و نەخشەکانی پەیوەندی لە داتاشیتی بەرھەمھێنەردا پێناسە کراون. سەرنجی بدە بۆ شوێنپێی ورد و ڕێنمایییەکانی لەحیمکردن.

نەخشەی پینئاوتی پاکێجی 18-lead soic بۆ ADM242ARZ

هیچ داتای وردی پینئاوت بەردەست نییە بۆ ADM242ARZ.

سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.

بەکارهێنانە باوەکان

ADM242ARZ گونجاوە بۆ 6 بەکارھێنانs: Industrial Serial Console, Data-Acquisition Equipment, Instrumentation and Test Systems, Embedded Communications Adapter, Point-to-Point Equipment Link, Power-Managed Serial Port.

🏭

Industrial Serial Console

The ADM242ARZ fits industrial serial-console designs that require a 200 kB/s RS-232 link, two drivers, and two receivers from one 5 V supply. It can connect a controller to configuration, status, or diagnostic equipment while full-duplex operation supports simultaneous command and response traffic. The 0.1 µF charge-pump capacitors should be placed close to the IC, and the connector-side interface needs appropriate surge and ESD protection. Enable and shutdown controls let the system isolate or disable the interface during fault, reset, or low-power conditions. Because RS-232 is a balanced, bipolar interface, grounding and cable routing remain important in electrically noisy industrial environments.

📊

Data-Acquisition Equipment

The ADM242ARZ is suitable for data-acquisition equipment that exchanges configuration commands and sampled status information over RS-232. Its 200 kB/s transmission rate provides more headroom than slow legacy serial links, while the two-driver and two-receiver arrangement supports full-duplex communication from one device. The single 5 V supply simplifies integration with embedded control systems. Keep the charge-pump capacitors close to the package and route cable-side transients away from sensitive signal paths. Engineers should also account for the approximately 9 V bipolar output swing, 30 V receiver input range, and the need for connector protection when working with external equipment.

🔧

Instrumentation and Test Systems

The ADM242ARZ can provide the control and response link in instrumentation or test systems that exchange commands, measurements, and diagnostic records over RS-232. Its 200 kB/s maximum data rate supports moderate-speed automated test traffic, while two drivers and two receivers allow full-duplex operation. The 18-lead SOIC package is compatible with compact, surface-mounted test electronics. Layout should minimize the charge-pump loop, provide a stable 5 V rail, and separate sensitive measurement circuitry from the connector and cable-return paths. The EIA-232-E and V.28 compliance cited by Analog Devices provides a useful starting point, but the complete system must still meet its grounding and interface-noise requirements.

🌐

Embedded Communications Adapter

The ADM242ARZ is appropriate for embedded adapters that bridge a host processor or controller to a legacy RS-232 port. The 200 kB/s rate accommodates configuration downloads, status packets, and firmware-transfer workflows without requiring a separate external charge-pump design. With two drivers and two receivers, the transceiver can support bidirectional host-to-device communication using one 5 V supply. Designers should use the shutdown and enable controls to manage unused ports and reduce system power. PCB placement should prioritize short capacitor connections, a continuous ground reference, and protected cable entry points. Firmware should also handle RS-232 direction control and any half-duplex software coordination required by the connected peripheral.

🔗

Point-to-Point Equipment Link

The ADM242ARZ supports point-to-point links between two pieces of equipment when the interface uses a 5 V RS-232 transceiver with full-duplex capability. The two integrated drivers and receivers eliminate the need for separate line-driver and receiver packages, while the 200 kB/s rating handles moderate command and data traffic. Its on-chip charge pump requires only two 0.1 µF external capacitors to generate bipolar levels. Place those capacitors close to the IC and keep the charge-pump current loop compact. At the cable connector, add protection appropriate to the installation environment because external RS-232 lines can experience ESD, surge, and unintended voltage excursions.

⚡

Power-Managed Serial Port

The ADM242ARZ is useful in systems where the serial port must remain present but can be disabled during idle, reset, fault, or shutdown conditions. Its shutdown and enable functions provide direct control over the interface state, helping a system manage power around a 5 V supply. The ADM242 family supports data rates up to 200 kB/s, with two drivers and two receivers for full-duplex signaling. Validate the control polarity and timing against the Analog Devices datasheet before sequencing the port with other power domains. PCB layout should combine compact 0.1 µF charge-pump capacitor placement with a low-impedance ground path and protected connector-side routing.

What is the ADM242ARZ?
The ADM242ARZ is a 5 V, 200 kB/s RS-232 transceiver containing two line drivers and two receivers in an 18-lead SOIC package. According to the Analog Devices ADM242 product information, its integrated charge pump uses 0.1 µF external capacitors to generate bipolar RS-232 levels. It provides full-duplex operation, shutdown control, and enable control for power-managed serial-port designs.
What are the key specifications of ADM242ARZ that engineers should know?
The ADM242ARZ combines a 200 kB/s maximum data rate, single 5 V supply, two drivers, two receivers, and full-duplex RS-232 operation. According to the Analog Devices ADM242 datasheet, the on-chip charge pump requires only 0.1 µF capacitors, produces an approximately 9 V driver output swing, accepts receiver input levels up to 30 V, and meets EIA-232-E and V.28 specifications.
Where can I download the ADM242ARZ datasheet PDF?
The official ADM242 datasheet and product information are available from Analog Devices at https://www.analog.com/en/products/adm242.html. This manufacturer page provides the device description and links to supporting documentation. Use the Analog Devices page as the authoritative starting point for the complete electrical characteristics, pin descriptions, recommended operating conditions, and package drawings.
Where can I find the ADM242ARZ pinout?
The ADM242ARZ pinout is defined by the Analog Devices ADM242 datasheet for the 18-lead SOIC package. Use the package drawing and pin-description table to assign supply, ground, driver outputs, receiver inputs, shutdown, enable, and charge-pump capacitor connections. The generic package diagram linked from this page should be checked against the manufacturer pin table before PCB artwork is released.
Can the ADM242ARZ replace a standard RS-232 transceiver?
The ADM242ARZ can serve as a replacement only when the existing design matches its 5 V supply, 200 kB/s interface rating, 18-lead SOIC footprint, enable and shutdown functions, and required RS-232 electrical behavior. According to the Analog Devices ADM242 product information, the device provides two drivers, two receivers, full duplex, and EIA-232-E and V.28 compliance. PCB and firmware compatibility must therefore be checked rather than assumed.
What is the best drop-in replacement for ADM242ARZ?
The closest documented same-brand drop-in candidate is the ADM242AR, which represents the same ADM242 200 kB/s RS-232 family in an 18-lead SOIC configuration. The cross-reference record identifies it as a replacement candidate for ADM242AR. Exact pinout, shutdown and enable behavior, electrical ratings, and lifecycle status should still be confirmed against the applicable Analog Devices datasheet before production substitution.
What is the difference between ADM242ARZ and ADM242AR?
The ADM242ARZ is the 18-lead SOIC ordering option identified in the product records, while ADM242AR is a closely related ADM242-family ordering designation. The cross-reference information treats ADM242AR as a replacement candidate for the ADM242AR family. Because package suffixes can encode temperature grade, packing method, or production status, verify the ordering table rather than treating the suffix difference as an automatic functional change.
When should I choose ADM242ARZ over ADM242AR?
Choose ADM242ARZ when the design requires the specified 18-lead SOIC ADM242ARZ configuration and its documented 200 kB/s RS-232 performance. Choose ADM242AR only after confirming that its package, pin assignment, supply voltage, control functions, and operating ratings are identical for the target board. The ADM242ARZ is preferable when the exact approved part number must be maintained for qualification, traceability, or change-control reasons.
Is ADM242ARZ suitable for industrial serial communication?
The ADM242ARZ is suitable for many industrial serial-console, data-acquisition, and control applications that use RS-232 at up to 200 kB/s. According to the Analog Devices ADM242 datasheet, the device supports full duplex, EIA-232-E and V.28 requirements, and externally controlled shutdown and enable states. Its suitability still depends on surge protection, grounding, cable length, and the environment-specific temperature requirement.
Does ADM242ARZ need external RS-232 charge-pump capacitors?
The ADM242ARZ requires external 0.1 µF charge-pump capacitors as specified by the Analog Devices ADM242 datasheet. These capacitors allow the integrated charge pump to generate the bipolar voltage swing needed for RS-232 signaling from a single 5 V supply. Place each capacitor close to its associated IC pins and keep the high-current charge-pump loop compact to reduce radiated and conducted switching disturbance.
How much power does the ADM242ARZ interface require?
The ADM242ARZ operates from a single 5 V supply and includes shutdown and enable controls for managing operating states. The manufacturer identifies the device as a 5 V RS-232 transceiver family member with an integrated charge pump. Application-specific supply current depends on operating mode, load, and signal activity, so use the manufacturer datasheet’s supply-current and shutdown-current characteristics for the final power-budget calculation.
Where can I buy ADM242ARZ online?
Use the Request a Quote form on this page to request the ADM242ARZ, current unit availability, and the quantity break you need. The form is the appropriate channel for current price, stock, minimum order quantity, and lead-time confirmation because commercial conditions can change. Request the 18-lead SOIC ordering option and confirm the intended packing method in the quotation request.
What is the price of ADM242ARZ?
The current ADM242ARZ price is shown through the Request a Quote form on this page, where quantity and order details can be entered for a commercial response. This avoids presenting a stale or unqualified starting-price figure. For budgeting, include the required quantity, packaging preference, production schedule, and any grade or traceable-document requirements in the same request.
What is the lead time and stock status for ADM242ARZ?
Request the current ADM242ARZ stock position, minimum order quantity, and lead time through the Request a Quote form on this page. The manufacturer’s family information supports the ADM242 product line, but it does not establish a fixed quantity-on-hand or production lead time for every order. A formal quotation should confirm the exact MPN, packing option, and delivery schedule.
What can replace ADM242ARZ in a design?
ADM242AR is the clearest documented drop-in replacement candidate for the ADM242AR family because the cross-reference record associates it with ADM242AR-series replacement and the 18-lead SOIC configuration. Before replacing the device, compare pin names, driver and receiver counts, 5 V supply operation, 200 kB/s rating, shutdown and enable behavior, and package dimensions. The replacement must also satisfy the original system’s EMC and interface requirements.
Is there a Maxim Integrated equivalent for ADM242ARZ?
A Maxim Integrated or Sipex pin-to-pin alternative may exist, but the cross-reference results do not identify a specific orderable MPN whose footprint and electrical behavior can be verified here. Do not select a substitute from a manufacturer family name alone. Request or identify a concrete MPN, then confirm its 18-lead SOIC pinout, 200 kB/s capability, supply voltage, control pins, and RS-232 compliance before approving it as a drop-in replacement.

داتای سەرچاوەی ئەندازیاری بۆ ADM242ARZ — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.

ڕێنمایی هەڵبژاردن

Choose the ADM242ARZ when the design requires the exact 18-lead SOIC ordering option for a 5 V, 200 kB/s RS-232 interface with two drivers, two receivers, shutdown, and enable control. It is well suited to industrial consoles, test equipment, data-acquisition systems, and embedded adapters that need a compact full-duplex transceiver. ADM242AR is the closest same-family drop-in candidate when supply-chain flexibility or an equivalent ordering designation is required, but its temperature grade, packing method, lifecycle condition, and pin assignment should be checked before approval. Other manufacturers may offer related RS-232 transceivers; however, a generic functional equivalent does not establish a drop-in replacement. A substitute must match the 18-lead SOIC footprint, pinout, 5 V supply, control functions, 200 kB/s capability, and EIA-232-E or V.28 requirements. For designs emphasizing simple power management, the ADM242ARZ’s shutdown and enable functions are useful, but they must be sequenced correctly and paired with connector-side protection.

بەراوردکردن لەگەڵ جێگرەوەکان

پارامەتر ئەم بەرهەمە ADM242AR
Brand Analog Devices Analog Devices
Package 18-lead SOIC 18-lead SOIC
Transmission Rate 200 kB/s 200 kB/s
Supply Voltage 5 V 5 V
Number of Drivers 2 2
Number of Receivers 2 2
Charge-Pump Capacitor Value 0.1 µF 0.1 µF
Driver Output Swing Approximately 9 V Approximately 9 V
Duplex Mode Full duplex Full duplex
Shutdown and Enable Control Yes Yes
RS-232 Compliance EIA-232-E and V.28 EIA-232-E and V.28

جیاکەرەوە سەرەکییەکان

  • Combines two drivers and two receivers in one package (بەراورد بەADM242AR)
  • Higher stated transmission rate than conventional legacy RS-232 interfaces (بەراورد بەADM242AR)
  • Single-supply bipolar RS-232 operation with small charge-pump capacitors (بەراورد بەADM242AR)

تێبینییەکانی دیزاین

Place the two 0.1 µF charge-pump capacitors as close as practical to the pins specified by the Analog Devices ADM242 datasheet. Keep the capacitor and charge-pump current loop compact, use the shortest practical ground return, and avoid routing the loop beneath sensitive analog or high-impedance signal paths. This arrangement helps limit the switching disturbance generated by the integrated charge pump.

Do not treat the connector side of an RS-232 interface as ordinary logic. Driver outputs develop an approximately 9 V bipolar swing, and receiver inputs extend to 30 V, so external cables can introduce ESD, surge, and overvoltage conditions. Place protection at the board entry point, use a defined signal-ground reference, and verify the protection scheme does not distort valid RS-232 transitions.

Budget the 5 V supply for the transceiver, charge-pump load, and attached logic rather than assuming standard CMOS quiescent current. Use enable and shutdown states to control the interface when the host does not need continuous communications. Confirm timing, control polarity, and state current from the manufacturer datasheet, and avoid sequencing the RS-232 transceiver into a partially powered cable-side interface.

Provide a low-impedance ground plane and route each RS-232 signal as a dedicated conductor with a corresponding ground reference where the application permits. Keep the cable-side protection network close to the connector and separate from the charge-pump capacitor area. Review the finished layout for return-current continuity, especially if the RS-232 connector is physically separated from the logic ground.

زانیاری پابەندبوون

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
بێ قوڕقوشم
Unknown
بێ ھالۆجین
Unknown
کانزا ناکۆکەکان
Unknown

The ADM242 product information confirms EIA-232-E and V.28 interface compliance, but it does not explicitly state RoHS, REACH, lead-free, halogen-free, conflict-minerals, or automotive qualification status. AEC-Q100 is not applicable because this is a general-purpose RS-232 interface IC rather than an automotive-qualified device.

داتا پشتڕاستکراوەتەوە لە: 2026-11-09 — داتا لەلایەن تیمی ئەندازیاری پێکھاتەکانی XAIPART پشتڕاستکراوەتەوە و ڕێکخراوە

گەڕانە پەیوەندیدارەکان

ADM242ARZ datasheet ADM242ARZ pinout ADM242ARZ datasheet pdf ADM242ARZ equivalent ADM242ARZ replacement ADM242ARZ cross reference ADM242ARZ vs ADM242AR ADM242ARZ price ADM242ARZ stock Analog Devices ADM242ARZ ADM242ARZ 18 SOIC ADM242ARZ RS-232 application circuit

پێکهاتە و زاراوە پەیوەندیدارەکان

Analog Devices ADM242ARZ ADM242AR RS-232 RS-232 transceiver line driver line receiver interface IC semiconductor EIA-232-E V.28 full duplex single 5 V supply charge pump 0.1 µF capacitor 200 kB/s approximately 9 V output swing 30 V receiver input level shutdown control enable control 18-lead SOIC surface mount industrial serial communication data acquisition test and measurement
داواکاری نرخی خێرا RFQ
وردەکارییەکانی تەواو پڕ بکەرەوە — تیمی فرۆشتنی ئێمە لە ماوەی 24 کاتژمێردا وەڵام دەداتەوە
ژمارەی پارچە بەرهەمهێنەر پاکەت QTY نرخی ئامانج کۆی گشتی
✓
نرخەکە نێردرا!

لە ماوەی ٢٤ کاتژمێردا وەڵامی ئیمەیڵەکەت دەدەینەوە

1
داواکاری نرخ پێشکەشکرا
2
نرخپێدان وەرگیرا
3
داواکاری دانرا
4
پارەدان
5
نێردرا
6
گەیەنراوە
بینینی وردەکاریی داواکاری نرخ