ADM242ARZ - 200 kB/s RS-232 Transceiver | Analog Devices
부품 번호: ADM242ARZ ✓ 활성ADM242ARZ 개요
An RS-232 transceiver is an interface IC that combines line drivers and line receivers into a complete logic-side-to-serial-port link. Within the hierarchy of interface ICs, RS-232 transceivers convert standard logic-level signals into differential-voltage, bipolar signaling and then recover the incoming serial data. The ADM242 family is designed for equipment requiring higher serial throughput than conventional RS-232 transceivers while retaining the familiar single-supply implementation.
Key features include a maximum transmission rate of 200 kB/s, operation from one 5 V supply, two integrated drivers, and two integrated receivers. The on-chip charge pump requires only 0.1 µF external capacitors. According to the Analog Devices ADM242 product information, the circuit meets EIA-232-E and V.28 specifications and supports full-duplex RS-232 communication. Shutdown and enable controls add flexibility for systems that need to reduce supply current or manage peripheral power states.
The charge-pump architecture raises the low-side driver output above the normal logic supply range, enabling approximately 9 V output swing with a 5 V supply. Receiver input levels extend to 30 V, supporting the wider voltage range associated with RS-232 ports. Because these are bipolar line signals, designers should protect exposed serial interfaces against surge, ESD, and accidental overvoltage conditions rather than treating every connector-side node as ordinary logic.
Typical applications include industrial serial consoles, data-acquisition equipment, instrumentation, communications adapters, and embedded systems that exchange RS-232 data over cable runs. The 200 kB/s rate is suitable for moderate-speed control and diagnostic traffic, including configuration transfers and periodic status reporting. Systems requiring continuous data flow, very low power, or longer unrepeated distances should compare the interface requirements against the exact RS-232 timing, noise, and cable-loss limits.
The principal design consideration is capacitor placement. Position the 0.1 µF charge-pump capacitors close to their designated pins and route the associated current paths carefully to minimize switching disturbance on sensitive circuitry. Place input and output protection components where cable-side connections enter the board, and confirm that the exposed metal package area has adequate copper for thermal dissipation and, where required, an exposed-pad connection.
This page combines the manufacturer’s interface specifications, packaging information, practical application guidance, and a documented drop-in comparison to support faster design review and sourcing decisions. It also identifies where detailed pin assignments and procurement conditions must be checked directly against the Analog Devices datasheet and the Request a Quote form.
드롭인 대체품: ADM242ARZ — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: ADM242ARZ (동일 폼 팩터 및 풋프린트) — 차이점: Package, Mounting Type, Supply Voltage, Product Type.
ADM242AR
✅ 드롭인 ⚠️ 사양 미검증가격 문의
데이터시트 보기 →ADM242ARZ 사양
| Transmission Rate | 200 kB/s |
| 공급 전압 | 5 V |
| Charge-Pump Capacitor Value | 0.1 µF |
| Number of Drivers | 2 |
| Number of Receivers | 2 |
| Driver Output Swing | Approximately 9 V |
| Receiver Input Levels | 30 V |
| Duplex Mode | Full duplex |
| Shutdown Control | Yes |
| Enable Control | Yes |
| RS-232 Compliance | EIA-232-E and V.28 |
| 패키지 | 18-lead SOIC |
| 실장 유형 | Surface mount |
| 핀 수 | 18 |
| Document Revision | Rev. C |
ADM242ARZ 18-lead soic 핀 구성 가이드
ADM242ARZ(18-lead soic 패키지)의 핀 구성입니다. 핀 번호, 기능, 연결 다이어그램은 제조사 데이터시트에 정의되어 있습니다. 정확한 풋프린트와 솔더링 지침은 해당 문서를 참조하십시오.
다음에 대한 상세 핀아웃 데이터 없음: ADM242ARZ.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
ADM242ARZ 적합 용도: 6 애플리케이션s: Industrial Serial Console, Data-Acquisition Equipment, Instrumentation and Test Systems, Embedded Communications Adapter, Point-to-Point Equipment Link, Power-Managed Serial Port.
Industrial Serial Console
The ADM242ARZ fits industrial serial-console designs that require a 200 kB/s RS-232 link, two drivers, and two receivers from one 5 V supply. It can connect a controller to configuration, status, or diagnostic equipment while full-duplex operation supports simultaneous command and response traffic. The 0.1 µF charge-pump capacitors should be placed close to the IC, and the connector-side interface needs appropriate surge and ESD protection. Enable and shutdown controls let the system isolate or disable the interface during fault, reset, or low-power conditions. Because RS-232 is a balanced, bipolar interface, grounding and cable routing remain important in electrically noisy industrial environments.
추천
Data-Acquisition Equipment
The ADM242ARZ is suitable for data-acquisition equipment that exchanges configuration commands and sampled status information over RS-232. Its 200 kB/s transmission rate provides more headroom than slow legacy serial links, while the two-driver and two-receiver arrangement supports full-duplex communication from one device. The single 5 V supply simplifies integration with embedded control systems. Keep the charge-pump capacitors close to the package and route cable-side transients away from sensitive signal paths. Engineers should also account for the approximately 9 V bipolar output swing, 30 V receiver input range, and the need for connector protection when working with external equipment.
추천
Instrumentation and Test Systems
The ADM242ARZ can provide the control and response link in instrumentation or test systems that exchange commands, measurements, and diagnostic records over RS-232. Its 200 kB/s maximum data rate supports moderate-speed automated test traffic, while two drivers and two receivers allow full-duplex operation. The 18-lead SOIC package is compatible with compact, surface-mounted test electronics. Layout should minimize the charge-pump loop, provide a stable 5 V rail, and separate sensitive measurement circuitry from the connector and cable-return paths. The EIA-232-E and V.28 compliance cited by Analog Devices provides a useful starting point, but the complete system must still meet its grounding and interface-noise requirements.
추천
Embedded Communications Adapter
The ADM242ARZ is appropriate for embedded adapters that bridge a host processor or controller to a legacy RS-232 port. The 200 kB/s rate accommodates configuration downloads, status packets, and firmware-transfer workflows without requiring a separate external charge-pump design. With two drivers and two receivers, the transceiver can support bidirectional host-to-device communication using one 5 V supply. Designers should use the shutdown and enable controls to manage unused ports and reduce system power. PCB placement should prioritize short capacitor connections, a continuous ground reference, and protected cable entry points. Firmware should also handle RS-232 direction control and any half-duplex software coordination required by the connected peripheral.
추천
Point-to-Point Equipment Link
The ADM242ARZ supports point-to-point links between two pieces of equipment when the interface uses a 5 V RS-232 transceiver with full-duplex capability. The two integrated drivers and receivers eliminate the need for separate line-driver and receiver packages, while the 200 kB/s rating handles moderate command and data traffic. Its on-chip charge pump requires only two 0.1 µF external capacitors to generate bipolar levels. Place those capacitors close to the IC and keep the charge-pump current loop compact. At the cable connector, add protection appropriate to the installation environment because external RS-232 lines can experience ESD, surge, and unintended voltage excursions.
추천
Power-Managed Serial Port
The ADM242ARZ is useful in systems where the serial port must remain present but can be disabled during idle, reset, fault, or shutdown conditions. Its shutdown and enable functions provide direct control over the interface state, helping a system manage power around a 5 V supply. The ADM242 family supports data rates up to 200 kB/s, with two drivers and two receivers for full-duplex signaling. Validate the control polarity and timing against the Analog Devices datasheet before sequencing the port with other power domains. PCB layout should combine compact 0.1 µF charge-pump capacitor placement with a low-impedance ground path and protected connector-side routing.
추천
엔지니어링 참조 데이터: ADM242ARZ — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | ADM242AR |
|---|---|---|
| Brand | Analog Devices | Analog Devices |
| Package | 18-lead SOIC | 18-lead SOIC |
| Transmission Rate | 200 kB/s | 200 kB/s |
| Supply Voltage | 5 V | 5 V |
| Number of Drivers | 2 | 2 |
| Number of Receivers | 2 | 2 |
| Charge-Pump Capacitor Value | 0.1 µF | 0.1 µF |
| Driver Output Swing | Approximately 9 V | Approximately 9 V |
| Duplex Mode | Full duplex | Full duplex |
| Shutdown and Enable Control | Yes | Yes |
| RS-232 Compliance | EIA-232-E and V.28 | EIA-232-E and V.28 |
주요 차별점
- Combines two drivers and two receivers in one package (vs ADM242AR)
- Higher stated transmission rate than conventional legacy RS-232 interfaces (vs ADM242AR)
- Single-supply bipolar RS-232 operation with small charge-pump capacitors (vs ADM242AR)
설계 노트
Place the two 0.1 µF charge-pump capacitors as close as practical to the pins specified by the Analog Devices ADM242 datasheet. Keep the capacitor and charge-pump current loop compact, use the shortest practical ground return, and avoid routing the loop beneath sensitive analog or high-impedance signal paths. This arrangement helps limit the switching disturbance generated by the integrated charge pump.
Do not treat the connector side of an RS-232 interface as ordinary logic. Driver outputs develop an approximately 9 V bipolar swing, and receiver inputs extend to 30 V, so external cables can introduce ESD, surge, and overvoltage conditions. Place protection at the board entry point, use a defined signal-ground reference, and verify the protection scheme does not distort valid RS-232 transitions.
Budget the 5 V supply for the transceiver, charge-pump load, and attached logic rather than assuming standard CMOS quiescent current. Use enable and shutdown states to control the interface when the host does not need continuous communications. Confirm timing, control polarity, and state current from the manufacturer datasheet, and avoid sequencing the RS-232 transceiver into a partially powered cable-side interface.
Provide a low-impedance ground plane and route each RS-232 signal as a dedicated conductor with a corresponding ground reference where the application permits. Keep the cable-side protection network close to the connector and separate from the charge-pump capacitor area. Review the finished layout for return-current continuity, especially if the RS-232 connector is physically separated from the logic ground.
규정 준수 정보
The ADM242 product information confirms EIA-232-E and V.28 interface compliance, but it does not explicitly state RoHS, REACH, lead-free, halogen-free, conflict-minerals, or automotive qualification status. AEC-Q100 is not applicable because this is a general-purpose RS-232 interface IC rather than an automotive-qualified device.