ADM3077EARZ - 16Mbps RS-485/RS-422 Transceiver | Analog Devices
MPN: ADM3077EARZ ✓ چالاکADM3077EARZ گشتی
An RS-485/RS-422 transceiver is an interface IC that converts logic-level signals into balanced differential bus signals and receives differential bus signals into CMOS-compatible logic. These interfaces belong to the broader transceiver hierarchy and connect controllers, sensors, industrial equipment, and communications infrastructure over cables that can be exposed to electrostatic discharge and ground-potential differences. RS-422 emphasizes point-to-point, full-duplex balanced signaling, while RS-485 supports multipoint buses with multiple transceivers.
The ADM3077E family's 16 Mbps data rate makes it suitable for high-speed industrial communications rather than slow supervisory protocols. Its ±15 kV ESD protection adds a substantial margin for connector and cabling exposure, while true fail-safe receiver inputs help maintain defined logic states when the bus is idle. The hot-swap structure allows the enable pins to tolerate powered insertion and removal without immediate damage. Depending on the exact family configuration, half-duplex and full-duplex options are available, and the target is identified as a full-duplex RS-422/RS-485 transceiver.
The 3.3 V supply operation supports compact industrial, instrumentation, building-control, and embedded equipment where the transceiver must coexist with modern low-voltage digital logic. A 16 Mbps maximum signaling rate provides a substantial bandwidth margin over common low-rate field buses. The operating-temperature option extends from -40°C to +125°C, allowing use in industrial environments with wide ambient-temperature requirements.
Typical installations include industrial sensor networks, factory automation links, building-control equipment, remote I/O modules, and protected communication ports. The device is placed between a UART or controller and a twisted-pair bus, with termination, biasing, isolation, surge protection, and common-mode grounding handled according to the system topology.
PCB design should place the transceiver close to the connector, route the differential pair as a controlled-impedance pair, keep the ground connection short, and provide the required supply and bypass capacitors. Bus-node count, cable length, topology, and termination must be evaluated together because the 16 Mbps capability does not remove propagation-delay and reflection constraints.
This page consolidates the manufacturer specifications, verified sourcing information, same-family drop-in options, and application guidance engineers need to evaluate the ADM3077EARZ for protected RS-485 and RS-422 interfaces.
جێگرەوەکانی جێگۆڕکێ بۆ ADM3077EARZ — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
ADM3077EYRZ
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
ADM3077EARZ تایبەتمەندییەکان
| Product Type | RS-485/RS-422 transceiver |
| Supply Voltage Range | 3 V to 3.6 V |
| Nominal Supply Voltage | 3.3 V |
| Maximum Data Rate | 16 Mbps |
| ESD Protection | ±15 kV |
| Duplex Support | Full duplex |
| Bus Standards | RS-485 and RS-422 |
| Maximum Bus Nodes | 256 nodes |
| Fail-Safe Receiver | True fail-safe receiver inputs |
| Enable Input Structure | Hot-swap input structure on DE and RE |
| مەودای پلەی گەرمیی کارکردن | -40°C to +125°C |
| پاکێج | 8-SOIC |
| جۆری دامەزراندن | Surface mount |
| Transceiver Configuration | 1 transmitter and 1 receiver |
ڕێنمایی ڕێکخستنی پینی ADM3077EARZ 8-soic
ڕێکخستنی پین بۆ ADM3077EARZ (پاکێجی 8-soic). ژمارەدانی پین، فەنکشنەکان و نەخشەکانی پەیوەندی لە داتاشیتی بەرھەمھێنەردا پێناسە کراون. سەرنجی بدە بۆ شوێنپێی ورد و ڕێنمایییەکانی لەحیمکردن.
هیچ داتای وردی پینئاوت بەردەست نییە بۆ ADM3077EARZ.
سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.
بەکارهێنانە باوەکان
ADM3077EARZ گونجاوە بۆ 6 بەکارھێنانs: Industrial Automation Communication, Factory Sensor and Remote I/O, Building Control Network, Instrumentation and Test Equipment, Protected Communications Port, Embedded Equipment Communication.
Industrial Automation Communication
The ADM3077EARZ fits industrial automation links that need reliable balanced signaling over a factory cable. Its 16 Mbps maximum data rate provides ample bandwidth for controller data, while ±15 kV ESD protection adds robustness at connector-facing circuitry. Place the transceiver between the controller UART and the RS-485 or RS-422 bus, then select termination and biasing for the actual network topology. The 3 V to 3.6 V supply range permits direct integration with 3.3 V control logic. Industrial qualification should still include checks for sustained surge, ground offsets, long cables, branch stubs, and the system-wide operating-temperature requirement.
پێشنیارکراو
Factory Sensor and Remote I/O
The ADM3077EARZ is suitable for connecting remote I/O modules and sensors over a multidrop RS-485 bus. A 16 Mbps data rate can accommodate fast polling and short factory-floor links, and the family supports up to 256 nodes for appropriately designed networks. Its true fail-safe receiver behavior helps preserve a defined state when the bus is idle or a driver is disconnected. Designers should minimize cable stubs, use a twisted-pair differential route, place termination only where required by the topology, and provide local supply bypassing. Where remote devices can present large ground-potential differences, an isolated interface may be preferable.
پێشنیارکراو
Building Control Network
The ADM3077EARZ can bridge a building-control controller and RS-485 field devices while supporting a 16 Mbps signaling rate and a low 3.3 V supply. The ±15 kV bus-pin ESD protection is valuable when field wiring reaches equipment rooms and wall boxes. Use it as a protected interface stage between the controller UART and balanced building bus, keeping the transceiver close to the connector and routing the pair with a continuous reference plane. Termination values and bias networks depend on cable length and topology. Confirm the required temperature range and environmental certification for the installed equipment rather than assuming that general industrial suitability replaces product-specific qualification.
پێشنیارکراو
Instrumentation and Test Equipment
The ADM3077EARZ suits laboratory and field instrumentation that exchanges measurement-control data over a balanced RS-422 or RS-485 connection. Full-duplex operation can support dedicated transmit and receive paths when the selected configuration provides them, while the 16 Mbps rate supports high-speed data transfer over controlled test cabling. Connect the transceiver to the instrument's logic interface and bring the balanced pair to the external connector through a short controlled-impedance route. ESD protection helps manage connector transients, but test systems should include adequate grounding and may require additional surge protection for severe environments. Verify the exact pin functions and enable-control logic in the manufacturer datasheet before final routing.
پێشنیارکراو
Protected Communications Port
The ADM3077EARZ is appropriate for an exposed communications port that combines a 3.3 V supply with a high-speed balanced bus. Its ±15 kV ESD protection on RS-485 input and output pins improves tolerance of connector transients, while the 16 Mbps capability supports short, high-rate links to adapters or field modules. The implementation should place the transceiver near the connector, include supply bypass capacitance, route A and B as a differential pair, and provide bus bias and termination according to the network design. ESD protection does not replace overvoltage, surge, or isolation protection where those hazards exceed the device's supported levels.
پێشنیارکراو
Embedded Equipment Communication
The ADM3077EARZ allows a compact embedded controller to communicate through a standardized RS-485 or RS-422 interface without adding a high-power external transceiver. Its 3 V to 3.6 V operating range aligns with 3.3 V embedded systems, and the 16 Mbps rate supports fast command and status traffic. The interface still requires careful signal integrity work: decouple the supply locally, maintain a continuous ground reference, keep the bus route short and impedance matched, and avoid uncontrolled branch stubs. For devices exposed to user-accessible connectors, the ±15 kV ESD rating supports protection planning, but enclosure grounding and supplementary surge protection remain important.
پێشنیارکراو
کورتەی بەرهەمە پێشنیارکراوەکان
داتای سەرچاوەی ئەندازیاری بۆ ADM3077EARZ — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | ADM3077EYRZ |
|---|---|---|
| Brand | Analog Devices | Analog Devices |
| Package | 8-SOIC | 8-SOIC |
| Product Type | RS-485/RS-422 transceiver | RS-485/RS-422 transceiver |
| Supply Voltage Range | 3 V to 3.6 V | 3 V to 3.6 V |
| Maximum Data Rate | 16 Mbps | 16 Mbps |
| ESD Protection | ±15 kV | ±15 kV |
| Maximum Bus Nodes | 256 nodes | 256 nodes |
| Fail-Safe Receiver | True fail-safe receiver inputs | True fail-safe receiver inputs |
| Delivery Configuration | Tape and reel ordering code | Tube ordering code |
جیاکەرەوە سەرەکییەکان
- High-speed balanced-interface capability (بەراورد بەADM3070E family at 250 kbps)
- Substantial connector-facing ESD protection (بەراورد بەADM3073E family at 500 kbps)
- Multipoint-bus scalability (بەراورد بەADM3077EYRZ)
تێبینییەکانی دیزاین
Place the ADM3077EARZ close to the external connector and route the balanced bus as a controlled-impedance differential pair. Keep the A-to-B trace spacing consistent, provide a continuous reference plane, and avoid routing the pair through digital switching areas. Place local bypass capacitance at the device supply pins according to the manufacturer application circuit. A short transceiver-to-connector path improves ESD-current diversion and reduces the chance that connector transients propagate deeper into the equipment.
Do not assume that every 16 Mbps ADM307x member is a board-level replacement. The ADM3077E family includes half-duplex and full-duplex arrangements, and a published comparison identifies a non-pin-compatible enable and bus configuration for at least one ADM3078EYRZ variant. Confirm DE, RE, driver-input, receiver-output, and bus-pin assignments in the manufacturer pin table before substitution. Also verify the 3 V to 3.6 V supply requirement and the selected temperature-grade suffix rather than relying only on the family name.
Determine bus termination and fail-safe biasing from the complete network topology. Install termination only at the physical ends of the main bus rather than at every node, and avoid long branch stubs because their reflections can degrade the 16 Mbps signal. For long or uneven cables, evaluate propagation delay and transceiver timing even though the nominal data rate is 16 Mbps. Use twisted-pair wiring, controlled connectors, and a sound common-mode strategy to reduce radiated emissions and susceptibility to external noise.
زانیاری پابەندبوون
No target-specific compliance conclusion was established from the manufacturer listing snippets. Confirm RoHS, REACH, lead-free, halogen-free, and conflict-minerals documentation for the exact ADM3077EARZ ordering code before regulatory submission.