Analog Devices

ADM3077EARZ - 16Mbps RS-485/RS-422 Transceiver | Analog Devices

MPN: ADM3077EARZ ✓ نشط
3 V to 3.6 V Vdss RS-485 and RS-422 Rds(on) 8-SOIC Package
الحد الأدنى للطلب: 1 |

ADM3077EARZ نظرة عامة

The Analog Devices ADM3077EARZ is a 3 V RS-485/RS-422 transceiver with a data rate of 16 Mbps, ±15 kV ESD protection on the bus pins, and an 8-SOIC package. It supports a 3 V to 3.6 V supply range, true fail-safe receiver inputs, hot-swap operation on the driver-enable and receiver-enable inputs, and operation from -40°C to +125°C.

An RS-485/RS-422 transceiver is an interface IC that converts logic-level signals into balanced differential bus signals and receives differential bus signals into CMOS-compatible logic. These interfaces belong to the broader transceiver hierarchy and connect controllers, sensors, industrial equipment, and communications infrastructure over cables that can be exposed to electrostatic discharge and ground-potential differences. RS-422 emphasizes point-to-point, full-duplex balanced signaling, while RS-485 supports multipoint buses with multiple transceivers.

The ADM3077E family's 16 Mbps data rate makes it suitable for high-speed industrial communications rather than slow supervisory protocols. Its ±15 kV ESD protection adds a substantial margin for connector and cabling exposure, while true fail-safe receiver inputs help maintain defined logic states when the bus is idle. The hot-swap structure allows the enable pins to tolerate powered insertion and removal without immediate damage. Depending on the exact family configuration, half-duplex and full-duplex options are available, and the target is identified as a full-duplex RS-422/RS-485 transceiver.

The 3.3 V supply operation supports compact industrial, instrumentation, building-control, and embedded equipment where the transceiver must coexist with modern low-voltage digital logic. A 16 Mbps maximum signaling rate provides a substantial bandwidth margin over common low-rate field buses. The operating-temperature option extends from -40°C to +125°C, allowing use in industrial environments with wide ambient-temperature requirements.

Typical installations include industrial sensor networks, factory automation links, building-control equipment, remote I/O modules, and protected communication ports. The device is placed between a UART or controller and a twisted-pair bus, with termination, biasing, isolation, surge protection, and common-mode grounding handled according to the system topology.

PCB design should place the transceiver close to the connector, route the differential pair as a controlled-impedance pair, keep the ground connection short, and provide the required supply and bypass capacitors. Bus-node count, cable length, topology, and termination must be evaluated together because the 16 Mbps capability does not remove propagation-delay and reflection constraints.

This page consolidates the manufacturer specifications, verified sourcing information, same-family drop-in options, and application guidance engineers need to evaluate the ADM3077EARZ for protected RS-485 and RS-422 interfaces.

بدائل مباشرة لـ ADM3077EARZ — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.

ADM3077EYRZ

✅ بديل مباشر
📦 8-SOIC
Same ADM3077E 16 Mbps RS-485/RS-422 device family and 8-SOIC format; ordering suffix differs by delivery configuration, while electrical differences are 0% for the documented core specifications

📋 بديل مرجعي (غير موجود في الكتالوج)

ADM3077EARZ المواصفات

Product Type RS-485/RS-422 transceiver
Supply Voltage Range 3 V to 3.6 V
Nominal Supply Voltage 3.3 V
Maximum Data Rate 16 Mbps
ESD Protection ±15 kV
Duplex Support Full duplex
Bus Standards RS-485 and RS-422
Maximum Bus Nodes 256 nodes
Fail-Safe Receiver True fail-safe receiver inputs
Enable Input Structure Hot-swap input structure on DE and RE
نطاق درجة حرارة التشغيل -40°C to +125°C
العلبة 8-SOIC
نوع التركيب Surface mount
Transceiver Configuration 1 transmitter and 1 receiver

دليل تكوين أطراف ADM3077EARZ 8-soic

تكوين الأطراف لـ ADM3077EARZ (حزمة 8-soic). يتم تعريف ترقيم الأطراف والوظائف ومخططات التوصيل في ورقة البيانات الفنية من الشركة المصنعة. راجعها للحصول على البصمة الدقيقة وإرشادات اللحام.

مخطط توزيع أطراف حزمة 8-soic لـ ADM3077EARZ

لا تتوفر بيانات مفصلة لمخطط التوصيلات لـ ADM3077EARZ.

راجع ورقة البيانات للحصول على تكوين الأطراف الكامل.

التطبيقات النموذجية

ADM3077EARZ مناسب لـ 6 التطبيقs: Industrial Automation Communication, Factory Sensor and Remote I/O, Building Control Network, Instrumentation and Test Equipment, Protected Communications Port, Embedded Equipment Communication.

🏭

Industrial Automation Communication

The ADM3077EARZ fits industrial automation links that need reliable balanced signaling over a factory cable. Its 16 Mbps maximum data rate provides ample bandwidth for controller data, while ±15 kV ESD protection adds robustness at connector-facing circuitry. Place the transceiver between the controller UART and the RS-485 or RS-422 bus, then select termination and biasing for the actual network topology. The 3 V to 3.6 V supply range permits direct integration with 3.3 V control logic. Industrial qualification should still include checks for sustained surge, ground offsets, long cables, branch stubs, and the system-wide operating-temperature requirement.

🧩

Factory Sensor and Remote I/O

The ADM3077EARZ is suitable for connecting remote I/O modules and sensors over a multidrop RS-485 bus. A 16 Mbps data rate can accommodate fast polling and short factory-floor links, and the family supports up to 256 nodes for appropriately designed networks. Its true fail-safe receiver behavior helps preserve a defined state when the bus is idle or a driver is disconnected. Designers should minimize cable stubs, use a twisted-pair differential route, place termination only where required by the topology, and provide local supply bypassing. Where remote devices can present large ground-potential differences, an isolated interface may be preferable.

🏠

Building Control Network

The ADM3077EARZ can bridge a building-control controller and RS-485 field devices while supporting a 16 Mbps signaling rate and a low 3.3 V supply. The ±15 kV bus-pin ESD protection is valuable when field wiring reaches equipment rooms and wall boxes. Use it as a protected interface stage between the controller UART and balanced building bus, keeping the transceiver close to the connector and routing the pair with a continuous reference plane. Termination values and bias networks depend on cable length and topology. Confirm the required temperature range and environmental certification for the installed equipment rather than assuming that general industrial suitability replaces product-specific qualification.

🖥️

Instrumentation and Test Equipment

The ADM3077EARZ suits laboratory and field instrumentation that exchanges measurement-control data over a balanced RS-422 or RS-485 connection. Full-duplex operation can support dedicated transmit and receive paths when the selected configuration provides them, while the 16 Mbps rate supports high-speed data transfer over controlled test cabling. Connect the transceiver to the instrument's logic interface and bring the balanced pair to the external connector through a short controlled-impedance route. ESD protection helps manage connector transients, but test systems should include adequate grounding and may require additional surge protection for severe environments. Verify the exact pin functions and enable-control logic in the manufacturer datasheet before final routing.

🌐

Protected Communications Port

The ADM3077EARZ is appropriate for an exposed communications port that combines a 3.3 V supply with a high-speed balanced bus. Its ±15 kV ESD protection on RS-485 input and output pins improves tolerance of connector transients, while the 16 Mbps capability supports short, high-rate links to adapters or field modules. The implementation should place the transceiver near the connector, include supply bypass capacitance, route A and B as a differential pair, and provide bus bias and termination according to the network design. ESD protection does not replace overvoltage, surge, or isolation protection where those hazards exceed the device's supported levels.

🔧

Embedded Equipment Communication

The ADM3077EARZ allows a compact embedded controller to communicate through a standardized RS-485 or RS-422 interface without adding a high-power external transceiver. Its 3 V to 3.6 V operating range aligns with 3.3 V embedded systems, and the 16 Mbps rate supports fast command and status traffic. The interface still requires careful signal integrity work: decouple the supply locally, maintain a continuous ground reference, keep the bus route short and impedance matched, and avoid uncontrolled branch stubs. For devices exposed to user-accessible connectors, the ±15 kV ESD rating supports protection planning, but enclosure grounding and supplementary surge protection remain important.

ملخص المنتجات الموصى بها

What are the key specifications of ADM3077EARZ that engineers should know?
The ADM3077EARZ is a 3.3 V, 16 Mbps RS-485/RS-422 transceiver with ±15 kV ESD protection and true fail-safe receiver inputs. According to the Analog Devices ADM3077E product page, the family operates from 3 V to 3.6 V, supports up to 256 bus nodes, provides hot-swap input structures on DE and RE, and includes an option rated from -40°C to +125°C. The exact ordering code is supplied in an 8-SOIC package. These characteristics place it among high-speed, protection-oriented balanced-interface devices for industrial cabling and embedded communications.
Where can I download the ADM3077EARZ datasheet PDF?
The official ADM3077EARZ documentation is available through Analog Devices' ADM3077E product page at https://www.analog.com/en/products/adm3077e.html. The manufacturer product page identifies Data Sheet Rev. F and provides the product selection table, documentation, hardware ecosystem, and ordering information. Use the manufacturer document for the final pin-description table, electrical limits, recommended application circuit, and package drawings before assigning PCB nets or selecting termination and protection components.
Where can I find the ADM3077EARZ pinout?
The ADM3077EARZ pinout and recommended application schematic should be taken from the pin-description table and package drawing in the Analog Devices ADM3077E Data Sheet Rev. F. The product listing identifies the device as an 8-SOIC, but the manufacturer document remains the controlling source for pin numbers, exposed functions, and supply connections. Do not infer pin assignments from another ADM307x member because the family includes half-duplex and full-duplex configurations with different bus and control arrangements.
What is the maximum data rate of the ADM3077EARZ?
The maximum data rate is 16 Mbps. Analog Devices lists the ADM3076E, ADM3077E, and ADM3078E as its 16 Mbps family members, while the lower-rate ADM3070E through ADM3075E options are listed at 250 kbps or 500 kbps. The 16 Mbps rating makes the ADM3077EARZ appropriate for short, controlled-impedance links and high-speed industrial equipment, although usable cable distance still depends on propagation delay, transceiver delay, topology, and termination.
What ESD protection does the ADM3077EARZ provide?
The ADM3077EARZ provides ±15 kV ESD protection on its RS-485 input and output pins. According to the Analog Devices ADM3077E product page, this protection is intended to improve system resilience when transceivers are connected to external cabling and connectors. The 15 kV figure should not be interpreted as immunity to every industrial surge event; an external surge-protection network, chassis grounding strategy, and adequate common-mode design may still be required for the installation.
Is the ADM3077EARZ suitable for industrial automation and factory systems?
Yes, the ADM3077EARZ fits industrial automation interfaces that require a high-speed balanced transceiver and broad temperature operation. Its principal advantages are a 16 Mbps data rate, a 3 V to 3.6 V supply range, ±15 kV ESD protection, true fail-safe receiver behavior, and an option for -40°C to +125°C operation. Factory systems still need to address bus topology, cable length, termination, isolation requirements, grounding, and protection from surges or sustained overvoltage events.
How is the ADM3077EARZ used in an RS-485 interface?
The ADM3077EARZ interfaces a controller's logic-level transceiver signals with a balanced RS-485 bus. The transmitter converts serial data into differential bus voltage, while the receiver converts differential bus voltage back into a logic signal. External resistors commonly establish the bus bias and termination, although their exact values depend on topology and cable length. The device's 16 Mbps capability supports high-speed links, but engineers should still constrain stub lengths, use a controlled-impedance pair, and place the transceiver near the connector.
Can the ADM3077EARZ be used for RS-422 communication?
Yes, the ADM3077EARZ supports both RS-485 and RS-422 balanced-data applications and is listed as a full-duplex RS-422/RS-485 transceiver. RS-422 normally uses a dedicated driver and receiver pair for point-to-point communication, whereas RS-485 permits a shared bus and multiple nodes. The correct connection depends on the full pin assignment and the selected ADM3077E configuration, so use the manufacturer's pin table and application circuit rather than assuming the bus wiring of a half-duplex member.
What is the best drop-in replacement for the ADM3077EARZ?
The closest identified same-family drop-in option is the ADM3077EYRZ, which retains the ADM3077E device identity and 8-SOIC ordering format. Its distinguishing ordering code appears to distinguish the variant, but the precise temperature grade or packing condition must be confirmed in the Analog Devices product-selection table. The cross-reference results do not establish five pin-compatible, parametrically equivalent devices, so reel-code variants and members with different duplex pin arrangements are not presented as drop-in replacements.
Can ADM3076EYRZ or ADM3078EYRZ replace the ADM3077EARZ?
The ADM3076EYRZ and ADM3078EYRZ share the 16 Mbps ADM307x family characteristics and an SOIC footprint class, but they are not confirmed as direct drop-in replacements for the ADM3077EARZ. One published comparison states that the ADM3078EYRZ-REEL7 is not pin-to-pin compatible with the ADM3077EARZ because their dedicated bus and combined-enable arrangements differ. Treat both as functionally related family members, then verify the exact pin functions and enable logic before considering a board-level substitution.
When should I choose the ADM3077EARZ instead of another ADM307x device?
Choose the ADM3077EARZ when the design requires the full-duplex RS-422/RS-485 device variant, a maximum signaling rate of 16 Mbps, 3.3 V operation, and ±15 kV ESD-protected bus pins. Lower-rate ADM3070E-family choices may suffice for 250 kbps links, while ADM3073E-family choices target 500 kbps. Among the 16 Mbps members, select the exact duplex, package, temperature-grade, and enable-pin configuration required by the schematic rather than choosing solely by the shared family name.
What is the difference between the ADM3077EARZ and ADM3077EYRZ?
Both MPNs belong to the ADM3077E family and therefore share the core 16 Mbps RS-485/RS-422 interface class. The final ordering suffix differentiates the specific package, temperature, and delivery configuration, so they are not necessarily identical in every environmental or commercial attribute. The ADM3077EARZ-REEL7 listing explicitly identifies a reel configuration, whereas the ADM3077EYRZ comparison identifies a tube configuration. Verify the exact suffix interpretation in Analog Devices' product-selection table before treating either ordering code as interchangeable.
Where can I buy the ADM3077EARZ and check its lead time?
Use the Request a Quote form on this page to request ADM3077EARZ pricing, stock confirmation, minimum order quantity, and current lead time. The manufacturer and distributor listings confirm an active product page and an orderable catalog designation, but they do not establish a fixed current lead time. For production planning, request the exact MPN without substituting a reel-code or tube-code variant, and specify the required delivery quantity and packaging.
How much does the ADM3077EARZ cost?
Current ADM3077EARZ pricing should be obtained through the Request a Quote form on this page because commercial terms and availability can change by quantity and order context. The manufacturer page identifies a family list price beginning at $2.63, while a distributor listing displays a different unit listing, so neither figure should be treated as a universal quantity-break quotation. Ask for the exact ADM3077EARZ ordering code, quantity, delivery location, and expected production schedule when requesting a firm offer.
Is the ADM3077EARZ in stock?
Stock status for the ADM3077EARZ should be confirmed through the Request a Quote form on this page at the time of purchase. The manufacturer product page and distributor listings show active sourcing records for the part, but a listing page alone does not guarantee that a requested quantity is immediately available. Include your required quantity, target date, and permitted reel or tube packaging so the quote can reflect an executable allocation rather than a generic catalog-status response.
What design checks are required for an ADM3077EARZ bus?
The main checks are supply decoupling, signal routing, termination, biasing, and protection placement. Place bypass capacitance close to the supply pins, route the balanced bus as a differential pair, and minimize the distance between the transceiver and connector. Determine termination from the network topology rather than placing it at every node. ESD protection is valuable at exposed connectors, but sustained surge or ground-potential hazards may require a dedicated industrial protection design.

بيانات مرجعية هندسية لـ ADM3077EARZ — المقارنة وإرشادات التصميم ومعلومات الامتثال.

دليل الاختيار

Choose the ADM3077EARZ when the design requires a 3.3 V, 16 Mbps RS-485/RS-422 transceiver with ±15 kV ESD protection, true fail-safe receiver behavior, and a full-duplex ordering option. The ADM3077EYRZ is the closest identified drop-in selection because it remains in the same ADM3077E family and 8-SOIC format, but confirm its suffix-specific temperature and delivery attributes before ordering. Lower-rate ADM3070E and ADM3073E family parts may be preferable when the bus operates at 250 kbps or 500 kbps, respectively, or when their documented pin and duplex arrangements better match the design. ADM3076EYRZ and ADM3078EYRZ are related 16 Mbps devices, but the published cross-reference information does not establish them as direct replacements for this target. Final selection should therefore consider exact pin compatibility, enable logic, duplex topology, temperature grade, supply range, and cable timing rather than family name alone.

المقارنة مع البدائل

المعامل هذا المنتج ADM3077EYRZ
Brand Analog Devices Analog Devices
Package 8-SOIC 8-SOIC
Product Type RS-485/RS-422 transceiver RS-485/RS-422 transceiver
Supply Voltage Range 3 V to 3.6 V 3 V to 3.6 V
Maximum Data Rate 16 Mbps 16 Mbps
ESD Protection ±15 kV ±15 kV
Maximum Bus Nodes 256 nodes 256 nodes
Fail-Safe Receiver True fail-safe receiver inputs True fail-safe receiver inputs
Delivery Configuration Tape and reel ordering code Tube ordering code

أبرز الفروقات

  • High-speed balanced-interface capability (مقابلADM3070E family at 250 kbps)
  • Substantial connector-facing ESD protection (مقابلADM3073E family at 500 kbps)
  • Multipoint-bus scalability (مقابلADM3077EYRZ)

ملاحظات التصميم

Place the ADM3077EARZ close to the external connector and route the balanced bus as a controlled-impedance differential pair. Keep the A-to-B trace spacing consistent, provide a continuous reference plane, and avoid routing the pair through digital switching areas. Place local bypass capacitance at the device supply pins according to the manufacturer application circuit. A short transceiver-to-connector path improves ESD-current diversion and reduces the chance that connector transients propagate deeper into the equipment.

Do not assume that every 16 Mbps ADM307x member is a board-level replacement. The ADM3077E family includes half-duplex and full-duplex arrangements, and a published comparison identifies a non-pin-compatible enable and bus configuration for at least one ADM3078EYRZ variant. Confirm DE, RE, driver-input, receiver-output, and bus-pin assignments in the manufacturer pin table before substitution. Also verify the 3 V to 3.6 V supply requirement and the selected temperature-grade suffix rather than relying only on the family name.

Determine bus termination and fail-safe biasing from the complete network topology. Install termination only at the physical ends of the main bus rather than at every node, and avoid long branch stubs because their reflections can degrade the 16 Mbps signal. For long or uneven cables, evaluate propagation delay and transceiver timing even though the nominal data rate is 16 Mbps. Use twisted-pair wiring, controlled connectors, and a sound common-mode strategy to reduce radiated emissions and susceptibility to external noise.

معلومات الامتثال

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
خالٍ من الرصاص
Unknown
خالٍ من الهالوجين
Unknown
المعادن المتنازع عليها
Unknown

No target-specific compliance conclusion was established from the manufacturer listing snippets. Confirm RoHS, REACH, lead-free, halogen-free, and conflict-minerals documentation for the exact ADM3077EARZ ordering code before regulatory submission.

تم التحقق من البيانات في: 2026-11-19 — تم التحقق من البيانات وتنسيقها بواسطة فريق هندسة المكونات في XAIPART

عمليات بحث ذات صلة

ADM3077EARZ datasheet ADM3077EARZ pinout ADM3077EARZ datasheet pdf ADM3077EARZ equivalent ADM3077EARZ replacement ADM3077EARZ cross reference ADM3077EARZ vs ADM3077EYRZ ADM3077EARZ price ADM3077EARZ stock Analog Devices ADM3077EARZ ADM3077E 16Mbps RS-485 ADM3077EARZ 8-SOIC ADM3077EARZ industrial interface

المكونات والمصطلحات ذات الصلة

Analog Devices ADM3077EARZ ADM3077EYRZ ADM3077E RS-485 RS-422 transceiver balanced differential signaling interface IC half-duplex full-duplex 16 Mbps 3.3 V supply ±15 kV ESD protection true fail-safe receiver hot-swap input 8-SOIC SOIC package family surface-mount package industrial automation building control remote I/O multipoint bus differential pair EMI protection
عرض سعر سريع RFQ
املأ التفاصيل الكاملة — سيرد فريق المبيعات لدينا خلال 24 ساعة
رقم القطعة الشركة المصنعة الحزمة QTY السعر المستهدف الإجمالي
✓
تم إرسال عرض السعر!

سنرد على بريدك الإلكتروني خلال 24 ساعة

1
تم إرسال طلب عرض السعر
2
تم استلام عرض السعر
3
تم تقديم الطلب
4
الدفع
5
تم الشحن
6
تم التسليم
عرض تفاصيل طلب عرض السعر