Analog Devices

ADM4850AR - 115 kbps RS-485/RS-422 Transceiver | Analog Devices

MPN: ADM4850AR ✓ چالاک
5 V Vdss 8-lead SOIC Package
MOQ: 1 |

ADM4850AR گشتی

The Analog Devices ADM4850AR is a 5 V, slew-rate-limited differential line transceiver supporting RS-485 and RS-422 communication at data rates up to 115 kbps. The device is available in an 8-lead SOIC package and supports half-duplex and full-duplex line configurations. Its controlled output slew rate reduces electromagnetic interference, while the integrated receiver includes a true fail-safe function for improved bus behavior when the driver is disabled.

A differential line transceiver converts between logic-level digital signals and balanced RS-485 or RS-422 signals. RS-485 is commonly used for multipoint industrial buses because differential signaling improves noise immunity and allows multiple nodes to share a two-wire bus when the system includes proper termination and biasing. RS-422 provides a balanced differential interface commonly used for point-to-point and legacy industrial communication links. The ADM4850AR belongs to the interface IC hierarchy and is positioned where a host UART or other controller must communicate over a physical bus.

The principal feature of the ADM4850AR is its reduced slew rate. Slower signal-edge transitions lower the high-frequency content radiated by the driver and can reduce EMI problems in cables, connectors, and surrounding circuitry. The maximum data rate is 115 kbps, making the device appropriate for low- and moderate-speed factory automation, building-control, instrumentation, and embedded equipment links rather than high-speed backplane or storage networking.

The ADM4850AR family includes multiple data-rate options, but the ADM4850 is the 115 kbps member. Half-duplex operation shares the driver and receiver path on the same bus pair, whereas full-duplex operation uses separate transmit and receive channels where the circuit topology permits it. Direction control and bus termination must be implemented correctly in the surrounding circuit, especially when the transceiver is used on a multipoint network with multiple drivers.

Typical applications include industrial RS-485 links between controllers and sensors, building-automation equipment, remote instrumentation, and embedded data-acquisition systems. The limited data rate and slew rate are useful when long cables, modest connector spacing, and mixed industrial equipment make high-edge-rate drivers less attractive. Firmware should also avoid relying on the transceiver as a termination element because line termination belongs in the external network.

For PCB design, place the transceiver close to the connector and bus interface, provide a solid ground reference, and keep differential traces routed as a closely coupled pair. The external network should follow the applicable RS-485 or RS-422 termination and biasing strategy. Confirm the complete pin assignment and operating limits in the manufacturer datasheet before finalizing a layout, especially when changing between half- and full-duplex configurations.

This page combines the ADM4850AR interface description, verified product links, practical bus-layout guidance, and carefully scoped replacement criteria. It emphasizes the electrical roles that determine whether an RS-485 transceiver can be substituted without changing the PCB or degrading signal integrity.

جێگرەوەکانی جێگۆڕکێ بۆ ADM4850AR — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.

جۆرەکان لەم زنجیرەیەدا

مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ ADM4850AR (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Package, Supply Voltage, Maximum Data Rate, Product Type, Receiver Fail-Safe.

Analog Devices
Package: 8-SOIC (SO-8, 3.9 mm body width)
Supply Voltage: 5 V ±10%
Receiver Fail-Safe: Yes (open-circuit, shorted input)
بەراوردکردن لەگەڵ ADM4850AR →
Analog Devices
Maximum Data Rate: 500 kbps
Product Type: RS-485/RS-422 differential line transceiver
بەراوردکردن لەگەڵ ADM4850AR →

هیچ جێگرەوەی ڕاستەوخۆ بۆ ئەم بەرهەمە بەردەست نییە.

داوای جێگرەوەکان بکە

ADM4850AR تایبەتمەندییەکان

Product Type Differential RS-485/RS-422 line transceiver
Manufacturer Analog Devices
ڤۆڵتیەی دابینکردن 5 V
Maximum Data Rate 115 kbps
Communication Standard EIA RS-485 and RS-422
Duplex Support Half-duplex and full-duplex
Slew Rate Slew-rate limited
Receiver Fail-Safe True fail-safe receiver
Transmitter and Receiver Count 1 transmitter and 1 receiver
Bus Configuration Multipoint bus transmission lines
پاکێج 8-lead SOIC
جۆری دامەزراندن Surface mount

ڕێنمایی ڕێکخستنی پینی ADM4850AR 8-lead soic

ڕێکخستنی پین بۆ ADM4850AR (پاکێجی 8-lead soic). ژمارەدانی پین، فەنکشنەکان و نەخشەکانی پەیوەندی لە داتاشیتی بەرھەمھێنەردا پێناسە کراون. سەرنجی بدە بۆ شوێنپێی ورد و ڕێنمایییەکانی لەحیمکردن.

نەخشەی پینئاوتی پاکێجی 8-lead soic بۆ ADM4850AR

هیچ داتای وردی پینئاوت بەردەست نییە بۆ ADM4850AR.

سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.

بەکارهێنانە باوەکان

ADM4850AR گونجاوە بۆ 6 بەکارھێنانs: Industrial Sensor Bus, Building Automation Network, Remote Instrumentation, Embedded Data Acquisition, Security and Access Control, Telecommunications Power Monitoring.

🏭

Industrial Sensor Bus

The ADM4850AR suits slow industrial sensor networks that communicate over an RS-485 cable at up to 115 kbps. Its slew-rate-limited driver reduces the high-frequency content that can couple into adjacent control wiring, while the differential receiver improves noise rejection on factory-floor links. Place the transceiver near the field connector, route the cable-side nets as a close differential pair, and implement termination only at the designated bus ends. Because the maximum rate is 115 kbps, the bus should be configured for polling-based sensors, temperature measurements, pressure readings, and other low-bandwidth instrumentation rather than high-speed streaming.

🏠

Building Automation Network

The ADM4850AR can connect a building controller to distributed HVAC, lighting-control, or environmental-monitoring units over a wired RS-485 network. Its 115 kbps limit is suitable for supervisory control and status reporting, and the controlled driver transitions help limit emissions into other building wiring. The interface design should include a defined logic ground or common reference, surge protection at the cable entry, and bus biasing that remains valid when every transmitter is disabled. Keep the UART baud rate within the 115 kbps transceiver limit and allow sufficient settling time for a full byte before the next transmission.

📡

Remote Instrumentation

The ADM4850AR is appropriate for linking laboratory or process instrumentation to a remote acquisition controller over RS-422 or RS-485. Differential signaling supports operation in electrically noisy environments, while the true fail-safe receiver helps maintain a defined receiver state when the driver is inactive. At the 115 kbps maximum rate, the link can carry commands, configuration data, and periodic measurements without requiring a high-speed physical layer. Use the full-duplex configuration when the system requires continuous receive capability and a separate transmit pair, or use half-duplex operation when wiring simplicity and shared-bus economics are more important.

🖥️

Embedded Data Acquisition

The ADM4850AR links an embedded controller or single-board computer to external sensors, remote I/O modules, and service equipment. Its 115 kbps throughput is sufficient for command polling, configuration downloads, diagnostic messages, and periodic telemetry, while its 8-lead SOIC package supports compact board placement. The UART protocol should include destination addressing, integrity checks, timeouts, and bus turnaround delays where multiple nodes share a half-duplex pair. Place termination near the physical cable endpoints rather than at every controller, and verify that the ground reference and protection strategy are appropriate for the installation environment.

🔒

Security and Access Control

The ADM4850AR can connect access-control readers, door controllers, or alarm panels over an RS-485 supervisory bus. The 115 kbps rate accommodates badge events, configuration traffic, and periodic health checks, and the controlled slew rate helps maintain EMC performance in systems containing many low-voltage cables. Use a protocol with device addressing, sequence control, and collision avoidance to prevent multiple nodes from driving the bus simultaneously. For installations with long outdoor runs, add appropriately rated surge and ESD protection at the cable boundary and verify that the system grounding method preserves receiver noise immunity.

⚡

Telecommunications Power Monitoring

The ADM4850AR can connect remote power-system monitors to a central supervisory controller where a 115 kbps RS-485 link is sufficient for alarms and status data. The device's differential receiver and true fail-safe behavior suit distributed cable networks in which transmitter idle states must remain predictable. Keep the data path isolated from high-energy switching nodes and route the bus away from motor and transformer wiring where practical. A complete installation should define cable length, topology, grounding, protective devices, and termination strategy, then confirm communication margins across temperature and supply-voltage extremes before production release.

What is the ADM4850AR?
The ADM4850AR is a 5 V differential line transceiver for RS-485 and RS-422 communication at rates up to 115 kbps. According to the Analog Devices manufacturer datasheet, the ADM4850 family supports half-duplex and full-duplex data communication on multipoint bus transmission lines. The AR package is an 8-lead SOIC, and the reduced slew rate is intended to limit high-frequency EMI from the driver.
What is the maximum data rate of the ADM4850AR?
The ADM4850AR supports a maximum data rate of 115 kbps. The Analog Devices manufacturer datasheet identifies ADM4850 as the 115 kbps member of the ADM4850 through ADM4857 family, while faster family members extend to 500 kbps, 2.5 Mbps, and 10 Mbps. Choose the ADM4850AR when a lower edge rate and reduced EMI are more important than maximum throughput.
Is the ADM4850AR suitable for half-duplex and full-duplex RS-485?
Yes, the ADM4850AR supports both half-duplex and full-duplex communication configurations. The Analog Devices manufacturer datasheet describes the ADM4850/4851/4852/4853 devices as half- and full-duplex-capable differential transceivers. The external direction-control logic, termination, and wiring must match the selected operating mode, and the complete pin table should be checked before PCB routing.
Why does the ADM4850AR use a reduced slew rate?
The ADM4850AR uses a slew-rate-limited driver to reduce the high-frequency energy present on the RS-485 or RS-422 line. Analog Devices identifies reduced slew rates as a method for lowering EMI. This behavior is particularly useful on industrial cables and longer interconnections, although the resulting 115 kbps maximum data rate makes the device better suited to control and instrumentation traffic than high-speed data transfer.
Where can I download the ADM4850AR datasheet PDF?
The official ADM4850AR datasheet PDF is available through the Analog Devices family document for ADM4850, ADM4851, ADM4852, ADM4853, ADM4854, ADM4855, ADM4856, and ADM4857. Use the Analog Devices product page for the latest document and device-selection information. The manufacturer datasheet is the authoritative source for pin assignments, electrical limits, recommended circuits, and operating conditions.
Where can I find the ADM4850AR pinout?
The ADM4850AR pinout is defined in the pin-description table of the Analog Devices ADM4850 family manufacturer datasheet. The AR device uses an 8-lead SOIC package. Use that table to assign driver inputs, receiver outputs, direction-control signals, supplies, and grounds rather than relying on the visual position of a package drawing alone.
What is the difference between RS-485 and RS-422 operation with the ADM4850AR?
The ADM4850AR can operate with RS-485 or RS-422 networks, but their wiring and termination practices differ. RS-485 commonly uses a shared bus and supports multipoint communication, while RS-422 is generally associated with balanced point-to-point links. The Analog Devices manufacturer datasheet identifies both standards for this family, but the system topology must determine the appropriate external wiring and network components.
What are the key specifications of ADM4850AR that engineers should know?
The ADM4850AR combines a 5 V supply, 115 kbps maximum data rate, RS-485/RS-422 compatibility, slew-rate limiting, true fail-safe reception, and an 8-lead SOIC package. These characteristics place it in the differential transceiver class of interface ICs. They make the device appropriate for low- and medium-speed industrial buses where reduced EMI and reliable operation with an idle bus are important.
What can replace the ADM4850AR?
A valid replacement for the ADM4850AR must use the same 8-lead SOIC footprint, preserve the relevant pin functions, and remain within the RS-485/RS-422 operating limits and the 115 kbps speed class. No drop-in replacement can be confirmed from the available cross-reference results. Do not substitute based only on the words RS-485 transceiver because package, direction-control logic, fail-safe behavior, and electrical limits must also be checked.
Is the ADM4850AR the same as ADM4851AR?
No. The ADM4850AR and ADM4851AR belong to the same Analog Devices transceiver family, but the ADM4850 supports up to 115 kbps while the ADM4851 supports up to 500 kbps. The higher speed of the ADM4851 can alter cable, termination, and EMI design considerations. They should not be treated as automatically interchangeable without reviewing the complete manufacturer specifications and pin configuration.
When should I choose the ADM4850AR over a faster RS-485 transceiver?
Choose the ADM4850AR when the link operates at 115 kbps or less and controlled edge rates are desirable for EMI reduction. According to the Analog Devices manufacturer datasheet, this family includes members operating at 115 kbps, 500 kbps, 2.5 Mbps, and 10 Mbps. Select a faster member only when the application genuinely requires greater throughput and the associated channel and signal-integrity requirements have been validated.
Is the ADM4850AR suitable for industrial instrumentation and automation buses?
The ADM4850AR is suitable for industrial instrumentation and automation links operating at 115 kbps or less. Its differential RS-485/RS-422 interface, true fail-safe receiver, and slew-rate-limited driver support reliable communication on wired industrial systems. Long cable runs still require correct termination, biasing, grounding, and protection against surge or ESD events.
Where can I buy the ADM4850AR online?
Use the Request a Quote form on this page to request the ADM4850AR and discuss current availability, order quantity, and delivery timing. The form allows purchasing teams to obtain a current quotation without relying on a stale listing price. For technical confirmation, use the official Analog Devices product page and family manufacturer datasheet before releasing the component into a new design.
What is the price of the ADM4850AR?
The current ADM4850AR price should be requested through the Request a Quote form on this page because commercial terms and availability can change. The form supports quantity-specific quotations and lead-time confirmation for an engineering or production order. Use the returned quotation for budget approval rather than relying on a historical or family-level starting price.
What is the lead time and stock status for the ADM4850AR?
Current stock and lead time for the ADM4850AR should be confirmed through the Request a Quote form on this page. Submit the required quantity, target date, and preferred shipment details so the purchasing team can provide a current commitment. Treat availability as order-dependent until a quotation confirms the exact 8-lead SOIC configuration and manufacturing status.
How should termination and biasing be designed for the ADM4850AR?
Termination and biasing belong in the external RS-485 network rather than inside the ADM4850AR. In a typical RS-485 bus, termination is placed at the physical ends of the cable and biasing establishes the correct idle state when no driver is active. Follow the application guidance in the Analog Devices manufacturer datasheet and account for the actual cable length, topology, number of nodes, and fault conditions.

داتای سەرچاوەی ئەندازیاری بۆ ADM4850AR — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.

ڕێنمایی هەڵبژاردن

The ADM4850AR is the appropriate choice when a design needs a 5 V RS-485/RS-422 transceiver, supports both half- and full-duplex operation, and communicates at no more than 115 kbps. Its slew-rate-limited driver is useful in industrial systems where reducing high-frequency EMI is a priority, while the true fail-safe receiver helps preserve a defined state when the bus is idle. It is less suitable when a protocol requires throughput above 115 kbps, very short board-level links where edge rate is unimportant, or applications needing a different package, isolation, or channel count. Before approving any substitution, verify the footprint, exact pin functions, supply limits, logic thresholds, direction-control arrangement, fail-safe behavior, and bus-drive capability. The available cross-reference results do not establish enough pin-compatible alternatives to recommend a drop-in replacement without an engineering review.

تێبینییەکانی دیزاین

Place the ADM4850AR close to the RS-485 or RS-422 connector and separate the cable-side route from sensitive analog circuitry. Route the differential pair together with a constant distance between traces where practical, avoid routing over discontinuous plane references, and minimize stubs from transceiver and protection components. Connect the logic ground and cable reference according to the system grounding architecture. These practices reduce radiated emissions and improve the receiver margin available on noisy industrial links.

Do not place termination resistors at every node. On a typical multidrop RS-485 bus, termination belongs at the two physical ends of the trunk, while biasing provides a valid idle state when all drivers are disabled. The ADM4850AR is a transceiver, not a termination network. Also ensure that direction-control firmware never leaves two drivers active on the same bus pair and that the UART baud rate remains within the 115 kbps device limit.

Use the ADM4850AR's slew-rate-limited operation as part of the EMC design rather than adding aggressive filtering without system analysis. Keep the differential cable path compact, provide a continuous reference, and place any TVS devices close to the connector with short return paths. Validate radiated and conducted emissions in the final enclosure because cable length, connector construction, grounding, and adjacent switching circuits can dominate the result even when the transceiver operates at 115 kbps.

زانیاری پابەندبوون

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
بێ قوڕقوشم
Unknown
بێ ھالۆجین
Unknown
کانزا ناکۆکەکان
Unknown

The manufacturer family document includes an automotive-model note, but it does not establish the qualification status of ADM4850AR in the available product material. Individual compliance fields remain unknown rather than inferred.

داتا پشتڕاستکراوەتەوە لە: 2026-11-03 — داتا لەلایەن تیمی ئەندازیاری پێکھاتەکانی XAIPART پشتڕاستکراوەتەوە و ڕێکخراوە

گەڕانە پەیوەندیدارەکان

ADM4850AR datasheet ADM4850AR pinout ADM4850AR datasheet pdf ADM4850AR equivalent ADM4850AR replacement ADM4850AR cross reference ADM4850AR 8 pin SOIC ADM4850AR 115 kbps ADM4850AR RS-485 transceiver Analog Devices ADM4850AR ADM4850AR price ADM4850AR stock

پێکهاتە و زاراوە پەیوەندیدارەکان

Analog Devices ADM4850AR ADM4850 RS-485 RS-422 differential line transceiver interface IC physical-layer transceiver multipoint bus half-duplex full-duplex slew-rate-limited driver true fail-safe receiver 115 kbps 5 V transceiver 8-lead SOIC SOIC family surface-mount package UART industrial automation building automation remote instrumentation EMI RS-485 termination bus biasing
داواکاری نرخی خێرا RFQ
وردەکارییەکانی تەواو پڕ بکەرەوە — تیمی فرۆشتنی ئێمە لە ماوەی 24 کاتژمێردا وەڵام دەداتەوە
ژمارەی پارچە بەرهەمهێنەر پاکەت QTY نرخی ئامانج کۆی گشتی
✓
نرخەکە نێردرا!

لە ماوەی ٢٤ کاتژمێردا وەڵامی ئیمەیڵەکەت دەدەینەوە

1
داواکاری نرخ پێشکەشکرا
2
نرخپێدان وەرگیرا
3
داواکاری دانرا
4
پارەدان
5
نێردرا
6
گەیەنراوە
بینینی وردەکاریی داواکاری نرخ