Analog Devices

ADM4852AR - 2.5Mbps RS-485 Transceiver | Analog Devices

MPN: ADM4852AR ✓ چالاک
5 V Vdss EIA RS-485 and RS-422 Rds(on) 8-lead SOIC Package
MOQ: 1 |

ADM4852AR گشتی

The Analog Devices ADM4852AR is a 5 V slew-rate-limited half-duplex and full-duplex RS-485/RS-422 differential line transceiver operating at data rates up to 2.5 Mbps. The device is offered in an 8-lead SOIC package and combines a differential driver, differential receiver, true fail-safe receiver behavior, and low-emissions operation for reliable data communication across multipoint bus transmission lines.

An RS-485 transceiver is an interface IC that converts logic-level signals into balanced differential signals for transmission over long, noisy cables, then converts incoming differential signals back into receiver-compatible logic. RS-485 belongs to the differential line-interface class within interface ICs and is widely used for industrial communication. RS-422 provides a related point-to-point differential signaling method, allowing one ADM4852-family device to address both common multipoint and dedicated-driver communication needs.

The ADM4852 family provides data-rate choices across multiple communication speeds, while the ADM4852 specifically supports operation up to 2.5 Mbps. Reduced slew rates are designed to limit high-frequency harmonics and electromagnetic interference, which is valuable when cables, connectors, or adjacent circuitry make EMI compliance difficult. The true fail-safe receiver feature improves behavior when the bus is idle, disconnected, or exposed to bus termination faults.

The family supports half-duplex and full-duplex configurations, allowing the same transceiver technology to serve shared multidrop buses and dedicated point-to-point links. Half-duplex operation requires bus-direction control so that the driver and receiver do not contend simultaneously. Full-duplex operation uses separate differential data paths and can simplify communication timing when simultaneous transmission and reception are required.

Typical uses include industrial control networks, building automation equipment, instrumentation links, factory data buses, and embedded systems communicating with remote sensors or controllers. The 2.5 Mbps rate is appropriate for moderately high-speed industrial links, while the slew-rate control helps suppress unwanted radiated emissions. Board-level implementation still requires correct termination, biasing, grounding, and protection according to the bus topology.

Design around the supply range, driver output limits, receiver thresholds, and maximum cable length rather than treating the 2.5 Mbps figure as a universal bus rate. Keep the transceiver and protection components close to the connector, maintain a continuous return path, and validate the complete network under its worst-case cable length, topology, and loading. The manufacturer datasheet provides the authoritative pin assignment, timing limits, electrical characteristics, and application diagrams.

This product page consolidates the manufacturer’s device description, exact-MPN pricing evidence, package information, pin-compatible replacement analysis, application guidance, and practical interface-design considerations into a focused engineering reference for evaluating the ADM4852AR in RS-485 and RS-422 systems.

جێگرەوەکانی جێگۆڕکێ بۆ ADM4852AR — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.

جۆرەکان لەم زنجیرەیەدا

مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ ADM4852AR (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Package, Slew Rate, Supply Voltage, Product Type.

Analog Devices
Package: 8-SOIC (SO-8, 3.9 mm body width)
Slew Rate: Limited (reduced for low EMI)
Supply Voltage: 5 V ±10%
بەراوردکردن لەگەڵ ADM4852AR →
Analog Devices
Package: 8-pin SOIC
Slew Rate: Reduced, slew-rate limited
بەراوردکردن لەگەڵ ADM4852AR →
Analog Devices
Package: 8-pin SOIC
Product Type: Differential line transceiver
بەراوردکردن لەگەڵ ADM4852AR →

ADM4852ARZ

✅ جێگرەوەی ڕاستەوخۆ
📦 8-lead SOIC
Same 2.5 Mbps ADM4852 device function and 8-lead SOIC format; ordering suffix denotes the lead-free variant rather than a change to the 2.5 Mbps data rate.

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

ADM4856AR

✅ جێگرەوەی ڕاستەوخۆ
Analog Devices
📦 8-lead SOIC
RS-485/RS-422 differential line transceiver · 5 V · 2.5 Mbps · Half-duplex and full-duplex · EIA RS-485 and RS-422 compliant · Reduced, slew-rate limited · True fail-safe receiver · 8-pin SOIC

پەیوەندی بۆ نرخ

بینینی داتاشیت →

ADM4852AR تایبەتمەندییەکان

Product Type RS-485/RS-422 differential line transceiver
ڤۆڵتیەی دابینکردن 5 V
Maximum Data Rate 2.5 Mbps
Communication Modes Half-duplex and full-duplex
Standards Compatibility EIA RS-485 and RS-422
Slew Rate Limited
Fail-Safe Receiver True fail-safe
Bus Topology Multipoint bus transmission lines
پاکێج 8-lead SOIC
جۆری دامەزراندن Surface mount
ژمارەی پینەکان 8 pins

ڕێنمایی ڕێکخستنی پینی ADM4852AR 8-lead soic

ڕێکخستنی پین بۆ ADM4852AR (پاکێجی 8-lead soic). ژمارەدانی پین، فەنکشنەکان و نەخشەکانی پەیوەندی لە داتاشیتی بەرھەمھێنەردا پێناسە کراون. سەرنجی بدە بۆ شوێنپێی ورد و ڕێنمایییەکانی لەحیمکردن.

نەخشەی پینئاوتی پاکێجی 8-lead soic بۆ ADM4852AR

هیچ داتای وردی پینئاوت بەردەست نییە بۆ ADM4852AR.

سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.

بەکارهێنانە باوەکان

ADM4852AR گونجاوە بۆ 6 بەکارھێنانs: Industrial RS-485 Control Bus, Building Automation Equipment, Remote Sensor Instrumentation, Factory Motor and Actuator Networks, Point-to-Point RS-422 Link, Embedded Communication Port.

🏭

Industrial RS-485 Control Bus

The ADM4852AR fits industrial control networks that require reliable differential signaling over multi-node copper cabling. Its 2.5 Mbps maximum data rate supports higher-speed supervisory and configuration traffic, while the reduced slew rate is intended to limit high-frequency EMI. In a half-duplex multidrop bus, the transceiver interfaces the controller UART to the differential network. Engineers should preserve the shared-bus direction-control arrangement, place termination at the physical ends, and validate the complete topology under the longest intended cable length.

🏭

Building Automation Equipment

The ADM4852AR can connect controllers, sensors, and field modules in building-automation equipment that uses RS-485. The 5 V transceiver architecture suits embedded control boards, and its 2.5 Mbps capability provides margin for local configuration and diagnostic traffic. The differential bus is preferable in building environments where cable routing can introduce ground offsets and interference. Maintain a controlled ground reference, use twisted-pair wiring, and select termination and protection values with the complete network topology in view.

📡

Remote Sensor Instrumentation

The ADM4852AR is suitable for linking a measurement instrument or data-acquisition unit to remotely distributed sensors. Its 2.5 Mbps rate supports modernized legacy sensor buses while true fail-safe receiver behavior improves digital-state predictability on idle or disconnected lines. The transceiver is placed at the cable boundary with surge protection and chassis-ground provisions, reducing the risk that external cable transients reach the controller. Cable length, common-mode range, protection response, and grounding must be evaluated together rather than relying on the headline data rate alone.

⚙️

Factory Motor and Actuator Networks

The ADM4852AR can serve as the bus interface in factory equipment that exchanges commands and status between a controller, motor controller, actuator, or remote I/O module. Its half-duplex capability is appropriate for shared networks, and the 2.5 Mbps data rate accommodates relatively fast command traffic. Reduced slew rates help suppress radiated emissions around control cabinets and machinery. The designer should add appropriately rated protection at exposed connectors and verify driver loading, idle biasing, and ground references across all powered and unpowered nodes.

🔗

Point-to-Point RS-422 Link

The ADM4852AR family supports RS-422 operation, making it applicable to dedicated point-to-point links between two equipment locations. Differential signaling improves noise immunity relative to single-ended communication, and the 5 V device operates at rates up to 2.5 Mbps. In this topology, the driver and receiver paths remain distinct rather than sharing a multidrop bus. Use twisted-pair wiring, provide a suitable reference connection, and confirm the receiver’s differential thresholds and common-mode limits against the installation environment.

🖥️

Embedded Communication Port

The ADM4852AR is useful for adding a robust differential communication port to an embedded controller, data logger, or service interface. Its 8-lead SOIC package supports conventional surface-mount assembly, while the 5 V supply is compatible with many embedded power systems. Connect the transceiver UART or logic interface to the host controller and keep the line-side routing short and separated from sensitive signals. Firmware must manage bus direction in half-duplex mode, detect communication faults, and avoid transmitting on an unterminated or excessively loaded bus.

What is the ADM4852AR?
The ADM4852AR is a 5 V differential RS-485/RS-422 transceiver capable of operation at up to 2.5 Mbps. According to the Analog Devices ADM4852 datasheet, it provides slew-rate-limited half-duplex and full-duplex operation, true fail-safe receiver behavior, and support for multipoint bus transmission lines. It is an interface IC used to connect digital logic to balanced industrial communication cables.
What are the key specifications of ADM4852AR that engineers should know?
The ADM4852AR operates from a 5 V supply and supports RS-485 and RS-422 differential signaling at data rates up to 2.5 Mbps. According to the Analog Devices datasheet, major features include reduced slew rates for low EMI, true fail-safe receiver operation, and half-duplex or full-duplex configurations. The device is available in an 8-lead SOIC package for surface-mounted PCB implementation.
Where can I download the ADM4852AR datasheet PDF?
The official ADM4852 product page is the appropriate starting point for the ADM4852AR datasheet PDF and related product documentation. According to Analog Devices, the ADM4852 family is described as a 5 V slew-rate-limited half- and full-duplex RS-485/RS-422 transceiver family. Use the manufacturer’s pin description table and electrical characteristics for the exact ADM4852AR ordering code.
Where can I find the ADM4852AR pinout?
The ADM4852AR pinout is shown in the manufacturer’s ADM4852 datasheet, which covers the 8-lead SOIC configuration used by this ordering code. According to the Analog Devices datasheet information, the device is an 8-lead interface IC. Use that pin-description table when assigning driver inputs, receiver outputs, enable controls, supplies, and bus terminals on the PCB.
What data rate does ADM4852AR support?
The ADM4852AR supports data rates up to 2.5 Mbps. According to the Analog Devices ADM4852 family description, reduced slew rates are included to lower electromagnetic interference while maintaining higher-speed differential communication. The actual usable rate also depends on cable length, topology, termination, connector performance, protection components, and the switching characteristics of connected nodes.
Does ADM4852AR support both half-duplex and full-duplex operation?
Yes, the ADM4852AR supports both half-duplex and full-duplex operation. According to the Analog Devices datasheet, the ADM4852 family includes half-duplex and full-duplex options for high-speed data communication. Half-duplex designs share a bus and require direction control, whereas full-duplex designs use separate differential paths for transmitting and receiving.
What does the true fail-safe receiver in ADM4852AR provide?
The true fail-safe receiver provides a defined receiver output state when the bus is idle or a driver is disconnected. According to the Analog Devices ADM4852 family description, true fail-safe operation improves system behavior in faulted or unconnected communication networks. It helps prevent uncontrolled digital states from being interpreted as valid commands by the connected controller.
Why is slew-rate limiting important in an ADM4852AR RS-485 bus?
Slew-rate limiting reduces the high-frequency content generated when the ADM4852AR driver changes output state. According to the Analog Devices datasheet, reduced slew rates are intended to provide low EMI. Slower edge rates can help reduce radiated emissions and ringing on long cables, although the final network must still be tested with its actual cable, connectors, termination, and protective circuitry.
Where can I buy ADM4852AR online?
Use the Request a Quote form on this page to request ADM4852AR pricing, stock, and order handling. The current commercial offer is handled through that form because inventory and commercial terms can change quickly. The manufacturer identifies ADM4852AR as an Analog Devices 5 V RS-485/RS-422 transceiver, and the product page provides the official technical documentation.
What is the price of ADM4852AR?
Request the current ADM4852AR price through the Request a Quote form on this page. Commercial pricing depends on quantity, order configuration, and current market conditions, so a static figure would quickly become inaccurate. The manufacturer’s product page and the exact-MPN ordering information should be used to confirm the intended 8-lead SOIC configuration before placing an order.
What is the lead time for ADM4852AR?
The current lead time should be requested through the Request a Quote form on this page. Lead time depends on the exact ordering code, order quantity, and current manufacturing and inventory conditions. Analog Devices identifies ADM4852AR as part of the ADM4852 5 V RS-485/RS-422 transceiver family, so confirm that suffix before treating any delivery estimate as applicable.
Is ADM4852AR in stock?
Current ADM4852AR stock status should be confirmed through the Request a Quote form on this page. The form allows the requested quantity and order configuration to be checked against current availability. The manufacturer’s ADM4852 product page remains the authoritative source for device status, documentation, and the exact ordering information.
What can replace ADM4852AR on the same 8-lead SOIC footprint?
ADM4852ARZ is the closest identified same-family option because it represents the lead-free ordering variant of the ADM4852AR in the 8-lead SOIC package. The Analog Devices family description identifies the ADM4852 as a 2.5 Mbps part, while the cross-reference results identify ADM4852ARZ as a related exact-family ordering option. Confirm pinout, temperature grade, and lifecycle status against the manufacturer datasheet before substitution.
Can ADM4856AR replace ADM4852AR?
The ADM4856AR is a related 2.5 Mbps member of the ADM485 transceiver family, but it represents a different duplex configuration within the family. According to the family description, the ADM4852 and ADM4856 both reach 2.5 Mbps while the family includes multiple half- and full-duplex options. Because transmit-enable and bus wiring can differ by configuration, verify the exact pinout before treating it as a drop-in replacement.
What is the best Analog Devices equivalent for ADM4852AR?
ADM4852ARZ is the best-identified Analog Devices equivalent because it is the lead-free ordering variant of the same ADM4852 2.5 Mbps family member and uses the corresponding 8-lead SOIC format. According to the Analog Devices family documentation, the ADM4852 operates at up to 2.5 Mbps. Confirm ordering information, lead finish, temperature coverage, and pin configuration against the manufacturer documentation before substitution.
ADM4852AR vs ADM4852ARZ - which should be selected?
ADM4852ARZ is the lead-free ordering variant of the ADM4852AR’s underlying device family, while ADM4852AR is the ordering code being evaluated. According to the Analog Devices ADM4852 product information, the device is a 5 V, 2.5 Mbps RS-485/RS-422 transceiver in an 8-lead SOIC package. Use the manufacturer’s ordering table to confirm whether the lead-free suffix satisfies the product and assembly requirements.

داتای سەرچاوەی ئەندازیاری بۆ ADM4852AR — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.

ڕێنمایی هەڵبژاردن

Choose ADM4852AR when the design needs a 5 V RS-485/RS-422 interface operating up to 2.5 Mbps with reduced slew-rate control for low EMI and true fail-safe receiver behavior. ADM4852ARZ is the closest identified ordering alternative because it retains the same ADM4852 function, speed class, and 8-lead SOIC format; use it when the lead-free ordering suffix meets assembly and procurement requirements. Consider ADM4856AR for a related same-family design requiring the full-duplex configuration. Do not substitute it solely on package similarity: compare transmit-enable logic, receiver connections, and bus wiring in the manufacturer pin tables. No cross-brand part is listed because the identified cross-reference results do not establish a complete same-footprint, within-parameter drop-in match.

بەراوردکردن لەگەڵ جێگرەوەکان

پارامەتر ئەم بەرهەمە ADM4852ARZ ADM4856AR
Package 8-lead SOIC 8-lead SOIC - same package 8-lead SOIC - same package
Brand Analog Devices Analog Devices Analog Devices
Product Type RS-485/RS-422 differential transceiver RS-485/RS-422 differential transceiver RS-485/RS-422 differential transceiver
Supply Voltage 5 V 5 V 5 V
Maximum Data Rate 2.5 Mbps 2.5 Mbps 2.5 Mbps
Duplex Configuration Half-duplex and full-duplex family options Same ADM4852 configuration Full-duplex family member
Standards Compatibility RS-485 and RS-422 RS-485 and RS-422 RS-485 and RS-422

جیاکەرەوە سەرەکییەکان

  • Maintains the same 2.5 Mbps speed class as the closest ordering variant (بەراورد بەADM4852ARZ)
  • Offers a same-family option with an alternate duplex architecture (بەراورد بەADM4856AR)
  • Combines reduced slew rate with true fail-safe reception (بەراورد بەADM4852ARZ)

تێبینییەکانی دیزاین

Keep the transceiver, termination network, protection components, and connector interface in one compact section of the PCB. Route the differential pair as a tightly coupled twisted pair on the external cable, maintain a continuous ground reference, and avoid routing the communications pair beside high-current switching nodes. Place the line-side protection close to the connector so transient current is diverted before it reaches the ADM4852AR.

Decouple the ADM4852AR supply with local high-frequency and bulk capacitance, following the manufacturer’s recommended application circuit. Place the smallest capacitor directly across the device supply pins and connect it to the ground plane without a long loop. Because the driver can deliver current into a terminated bus, evaluate supply droop and regulator headroom with the worst-case bus configuration rather than only the unloaded transceiver state.

Do not enable the driver while multiple nodes are transmitting, and do not assume that a 2.5 Mbps device supports 2.5 Mbps over every cable length. Termination belongs at the two physical ends of a multidrop bus, not at every node. Confirm fail-safe behavior, idle biasing, common-mode limits, and protection-device capacitance before production release.

The reduced slew rate is intended to limit electromagnetic interference, but cable and connector resonances can still produce overshoot and ringing. Use a controlled termination arrangement, minimize exposed stub lengths, and test radiated and conducted emissions with the final cable, shield, grounding, enclosure, and neighboring equipment. PCB changes should preserve the short return path of the differential interface.

زانیاری پابەندبوون

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
بێ قوڕقوشم
Unknown
بێ ھالۆجین
Unknown
کانزا ناکۆکەکان
Unknown

The ADM4852ARZ ordering suffix suggests a lead-free ordering option, but explicit RoHS, REACH, halogen-free, conflict-minerals, and AEC-Q100 statements were not identified. Use the manufacturer’s current declaration and product documentation for compliance decisions.

داتا پشتڕاستکراوەتەوە لە: 2026-11-03 — داتا لەلایەن تیمی ئەندازیاری پێکھاتەکانی XAIPART پشتڕاستکراوەتەوە و ڕێکخراوە

گەڕانە پەیوەندیدارەکان

ADM4852AR datasheet ADM4852AR pinout ADM4852AR datasheet pdf ADM4852AR equivalent ADM4852AR replacement ADM4852AR price ADM4852AR stock Analog Devices ADM4852AR ADM4852AR 2.5Mbps RS-485 ADM4852AR 8-lead SOIC ADM4852AR industrial bus ADM4852AR vs ADM4852ARZ ADM4852AR RS-422 transceiver ADM4852AR application circuit

پێکهاتە و زاراوە پەیوەندیدارەکان

Analog Devices ADM4852AR ADM4852ARZ ADM4856AR RS-485 RS-422 differential line transceiver half-duplex full-duplex multipoint bus slew-rate-limited transceiver true fail-safe receiver 2.5 Mbps 5 V transceiver EMI differential signaling 8-lead SOIC SOIC family surface-mount package interface IC industrial communication building automation remote instrumentation factory control network RS-485 termination
داواکاری نرخی خێرا RFQ
وردەکارییەکانی تەواو پڕ بکەرەوە — تیمی فرۆشتنی ئێمە لە ماوەی 24 کاتژمێردا وەڵام دەداتەوە
ژمارەی پارچە بەرهەمهێنەر پاکەت QTY نرخی ئامانج کۆی گشتی
✓
نرخەکە نێردرا!

لە ماوەی ٢٤ کاتژمێردا وەڵامی ئیمەیڵەکەت دەدەینەوە

1
داواکاری نرخ پێشکەشکرا
2
نرخپێدان وەرگیرا
3
داواکاری دانرا
4
پارەدان
5
نێردرا
6
گەیەنراوە
بینینی وردەکاریی داواکاری نرخ