Analog Devices

ADM485ANZ - 5V 5Mbps RS-485 Transceiver | Analog Devices

MPN: ADM485ANZ ✓ چالاک
5 V Vdss 8-pin PDIP Package
MOQ: 1 |

ADM485ANZ گشتی

The Analog Devices ADM485ANZ is a 5 V low-power differential line transceiver for bidirectional multipoint bus communications, supporting both EIA RS-485 and RS-422 in an 8-pin PDIP package. It combines one differential line driver with one differential receiver, and the manufacturer specifies operation at data rates up to 5 Mbit/s with low skew to minimize EMI interference.

An RS-485 transceiver is an interface IC that converts single-ended logic signals into balanced differential signals for reliable communication over longer, noisy cables. It belongs to the communication-interface hierarchy that includes RS-422 and RS-232 interface ICs, with the differential driver and receiver providing noise immunity, common-mode rejection, and multipoint-bus capability. The ADM485ANZ is suited to industrial, instrumentation, and embedded systems requiring bidirectional data transfer.

The ADM485 family supports independently controlled driver and receiver sections, allowing the transmitter and receiver to be disabled for low-power operation or configured for bus applications. Key characteristics include a 5 V supply, data rates up to 5 Mbit/s, and support for both RS-485 and RS-422. Its differential signaling reduces sensitivity to externally coupled noise compared with single-ended digital communication.

The small-signal architecture requires careful treatment of supply bypassing, grounding, and high-speed transmission lines. Because the ADM485ANZ supports data rates up to 5 Mbit/s, PCB trace impedance, connector geometry, cable characteristics, termination, and common-mode behavior can materially affect signal integrity. The 8-pin PDIP package is also easy to prototype and inspect, although it occupies more board area than surface-mount alternatives.

Typical applications include industrial process-control links, factory automation equipment, data acquisition systems, building-control networks, instrumentation buses, and embedded host interfaces. The device can support bidirectional communication when the driver and receiver are enabled together, or half-duplex bus operation when local bus management is required.

Designers should place the supply bypass capacitor close to the VCC pin, route the differential pair as a tightly coupled pair, and avoid placing high-current return paths beneath the transceiver. External termination, biasing, protection, and galvanic isolation should be selected from the cable length, baud rate, topology, and environmental conditions rather than applied unconditionally.

This product page combines the manufacturer's core ADM485 specifications with practical interface-design guidance, package details, sourcing information, and verified cross-reference candidates. The comparison material focuses on pin compatibility, data-rate support, supply requirements, and application fit so engineers can evaluate replacements without confusing merely similar RS-485 devices with true board-level alternatives.

جێگرەوەکانی جێگۆڕکێ بۆ ADM485ANZ — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.

جۆرەکان لەم زنجیرەیەدا

مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ ADM485ANZ (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Product Type, Supply Voltage, Mounting Type, Maximum Data Rate, Package.

Analog Devices
Supply Voltage: 5 V (single supply)
Mounting Type: Surface Mount
Package: SOIC-8 (SO-8) / SO-8
بەراوردکردن لەگەڵ ADM485ANZ →
Analog Devices
Product Type: RS-485/RS-422 differential line transceiver
Supply Voltage: +5 V
بەراوردکردن لەگەڵ ADM485ANZ →
Analog Devices
Maximum Data Rate: 5 Mbps
بەراوردکردن لەگەڵ ADM485ANZ →
Analog Devices
Product Type: RS-485/RS-422 Transceiver
Mounting Type: Surface Mount
بەراوردکردن لەگەڵ ADM485ANZ →

ADM485JNZ

✅ جێگرەوەی ڕاستەوخۆ
Analog Devices
📦 8-pin PDIP
1 transmitter and 1 receiver · EIA RS-485 and EIA RS-422 · 4.75 V to 5.25 V · 5 Mbps · +12 V · Differential driver and differential receiver · Logic-controlled input · Logic-controlled input

پەیوەندی بۆ نرخ

بینینی داتاشیت →

ADM485ARZ

✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە
Analog Devices
📦 8-pin PDIP
Transceiver · RS-422, RS-485 · 1/1 · Half · 5 V (single supply) · 5 Mbps (max) · -7 V to +12 V

پەیوەندی بۆ نرخ

بینینی داتاشیت →

SN65LBC176P

✅ جێگرەوەی ڕاستەوخۆ
📦 8-pin PDIP
Pin-compatible 8-pin PDIP RS-485/RS-422 transceiver; key electrical and timing parameters may differ by up to 30% from ADM485ANZ.

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

SN65176BP

✅ جێگرەوەی ڕاستەوخۆ
📦 8-pin PDIP
Pin-compatible 8-pin PDIP RS-485/RS-422 transceiver; key electrical and timing parameters may differ by up to 30% from ADM485ANZ.

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

SN75LBC184P

✅ جێگرەوەی ڕاستەوخۆ
📦 8-pin PDIP
Pin-compatible 8-pin PDIP differential-bus transceiver; key electrical and timing parameters may differ by up to 30% from ADM485ANZ.

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

ADM485ANZ تایبەتمەندییەکان

Product Type Differential RS-485/RS-422 line transceiver
ڤۆڵتیەی دابینکردن 5 V
Maximum Data Rate 5 Mbit/s
Transceiver Configuration 1 transmitter and 1 receiver
Communication Standard EIA RS-485 and RS-422
Bus Architecture Bidirectional multipoint bus
Signal Type Balanced differential
پاکێج 8-pin PDIP
جۆری دامەزراندن Through-hole
Temperature Range Commercial and industrial
Power Class Low-power

ڕێکخستنی پینی ADM485ANZ

DIP-8 Package Pinout Diagram DIP-8 8-pin dual inline, 7.62mm pitch, JEDEC MS-001. 1 8 2 7 3 6 4 5 DIP-8
پین 1 ROUT — Receiver output
پین 2 RE — Receiver enable input with active-low control
پین 3 DE — Driver enable input with active-high control
پین 4 DIN — Driver data input
پین 5 GND — Ground
پین 6 A — Noninverting differential bus terminal
پین 7 B — Inverting differential bus terminal
پین 8 VCC — Positive supply input

بەکارهێنانە باوەکان

ADM485ANZ گونجاوە بۆ 6 بەکارھێنانs: Industrial Process-Control Links, Factory Automation Equipment, Data-Acquisition Systems, Building-Control Networks, Instrumentation and Test Equipment, Embedded Communication Interfaces.

🏭

Industrial Process-Control Links

The ADM485ANZ fits industrial process-control equipment that exchanges commands and measurements between a controller and remote instrumentation. Its balanced differential driver and receiver support EIA RS-485 and RS-422 on cable runs where common-mode noise is a concern. Operation up to 5 Mbit/s is useful for short, high-speed control or diagnostic links, while independently controlled driver and receiver sections support half-duplex bus operation. The design must preserve a continuous ground reference, use a nearby 5 V bypass capacitor, and apply termination according to the physical bus layout.

🏭

Factory Automation Equipment

The ADM485ANZ can connect programmable controllers, sensors, motor-control modules, and remote I/O within a factory automation network. Differential signaling helps reject noise generated by motors, relays, and switching power supplies, while the 5 Mbit/s capability supports fast local data transfer. Driver and receiver enable pins give the host controller direct control over bus direction and low-power states. For factory equipment, route the A and B conductors as a pair, keep connector stubs short, add suitable transient protection, and verify that the selected cable length supports the operating baud rate.

📊

Data-Acquisition Systems

The ADM485ANZ is appropriate for laboratory and industrial data-acquisition systems that distribute measurements from multiple remote modules. Its one-driver/one-receiver arrangement supports balanced RS-485 and RS-422 links, and the 5 Mbit/s maximum rate can shorten transfer time for high-volume sample data. The receiver may also be used for monitoring while the driver remains disabled, depending on the bus architecture. Place the transceiver near the connector to minimize trace discontinuity, maintain a low-impedance ground connection, and select cable shielding and termination according to the laboratory environment and grounding strategy.

🏠

Building-Control Networks

The ADM485ANZ can support RS-485 communication among building controllers, room modules, sensors, and access-control equipment. Differential signaling provides a practical noise-control advantage when cables run near lighting, HVAC controls, and other switched loads. The ADM485ANZ's separate enable inputs allow a controller to manage transmit and receive intervals efficiently, and its 5 Mbit/s capability is useful for short equipment-room links. A robust installation should use isolated surge protection where field cables leave the building, maintain consistent reference grounding, and avoid excessive cable stubs or star branches.

🔧

Instrumentation and Test Equipment

The ADM485ANZ is useful in instrumentation and automated test equipment that must exchange commands and results over a balanced bus. Its 5 Mbit/s maximum data rate supports quick transfers between a controller and distributed measurement modules, while differential operation reduces susceptibility to common-mode interference in laboratory systems. The 8-pin PDIP package also facilitates prototyping and rework. Designers should use short, controlled-impedance board traces, provide local supply decoupling, confirm the logic thresholds of the connected controller, and add external protection if test leads can acquire electrostatic discharge or surge energy.

🖥️

Embedded Communication Interfaces

The ADM485ANZ gives an embedded controller a straightforward way to communicate with remote peripherals through a balanced differential bus. Its separate driver-input, driver-enable, receiver-enable, and receiver-output connections support both active communication and receive-only monitoring. A 5 V supply matches many embedded peripheral boards, while operation up to 5 Mbit/s covers short high-speed links and moderate-speed command traffic. Firmware should assert the driver enable only when the bus is free, and the hardware should include a defined fail-safe bias so an idle or disconnected bus is interpreted consistently by every node.

What is the ADM485ANZ?
The ADM485ANZ is a 5 V low-power differential transceiver for EIA RS-485 and RS-422 communication. It combines one differential line driver and one differential receiver in an 8-pin PDIP package. According to the Analog Devices ADM485 datasheet, the device supports bidirectional multipoint data rates up to 5 Mbit/s, making it appropriate for industrial, instrumentation, and embedded communication links.
What is the maximum data rate of ADM485ANZ?
The ADM485ANZ supports data rates up to 5 Mbit/s. According to the Analog Devices ADM485 product page and datasheet, the fast switching performance produces minimal driver propagation delay, while low skew helps reduce EMI interference. In practice, the installed system must also satisfy the baud-rate limits imposed by cable length, topology, termination, connector performance, and transceiver timing.
Where can I download the ADM485ANZ datasheet PDF?
The official ADM485ANZ datasheet PDF is available from Analog Devices at https://www.analog.com/media/en/technical-documentation/data-sheets/ADM485.pdf. The document describes the RS-485/RS-422 transceiver, electrical characteristics, pin configuration, and application information. Use the manufacturer PDF for design decisions because distributor summaries and third-party copies may omit revision-specific details.
Where can I find the ADM485ANZ pinout?
The ADM485ANZ uses an 8-pin PDIP package, and its numbered pin configuration appears in the Analog Devices ADM485 datasheet. The eight connections comprise the receiver output, driver input, enable controls, supply and ground, differential data terminals, and the complementary receiver input. Use the manufacturer pin-description table when assigning PCB tracks and guarding against signal or supply shorts.
Is the ADM485ANZ compatible with RS-422 and RS-485?
Yes, the ADM485ANZ complies with both EIA RS-485 and RS-422 requirements. According to the Analog Devices ADM485 product page, its balanced differential transmission supports reliable multipoint communication while reducing susceptibility to common-mode noise. RS-485 is commonly used for multipoint buses, whereas RS-422 emphasizes balanced point-to-point links; system topology still determines the correct termination and biasing arrangement.
Can ADM485ANZ communicate bidirectionally?
The ADM485ANZ supports bidirectional differential data communication because it contains both a driver and a receiver. According to the Analog Devices ADM485 datasheet, the driver and receiver have separate enable controls, allowing each section to be enabled or disabled. This flexibility supports half-duplex bus nodes, echo-free receiver-only monitoring, and applications where the transmitter must remain off during receive intervals.
What is the best drop-in replacement for ADM485ANZ?
The closest verified drop-in candidates are the ADM485JNZ and ADM485ARZ from Analog Devices, followed by suitably configured SN65LBC176P, SN65176BP, and SN75LBC184P devices. A valid replacement must match the 8-pin PDIP footprint, pin functions, supply voltage, direction-control behavior, and required data rate. Confirm all timing and electrical limits in the candidate manufacturer's datasheet before approving a substitution.
What can replace ADM485ANZ on the same PCB?
An ADM485ANZ board can potentially accept the ADM485JNZ or ADM485ARZ because both are members of the ADM485 family offered in the compatible leaded package configuration. Cross-brand choices identified for evaluation include the SN65LBC176P, SN65176BP, and SN75LBC184P. Pin placement alone is insufficient: verify driver-enable polarity, receiver-enable polarity, propagation delay, bus loading, and maximum data rate before replacement.
Is SN65LBC176P the same as ADM485ANZ?
The SN65LBC176P is a potential pin-compatible RS-485/RS-422 replacement, but it is not an identical device. It must be checked for equivalent enable polarity, receiver-output behavior, bus loading, electrical thresholds, and timing. According to the retrieved cross-reference records, both devices occupy the same 8-pin PDIP class, while application-level operating limits still require datasheet verification.
When should I choose ADM485ANZ over a lower-speed RS-485 transceiver?
Choose the ADM485ANZ when the bus must operate at rates up to 5 Mbit/s or when short-distance, high-speed links require low propagation delay and low skew. A slower transceiver may be appropriate for long cables or low-rate field buses, but it may not reproduce the ADM485ANZ's timing margin. Cable length, termination, node count, and environmental noise must be evaluated together with the target baud rate.
Is ADM485ANZ suitable for industrial automation equipment?
The ADM485ANZ is suitable for industrial automation interfaces when the system remains within its specified electrical and temperature limits. It provides balanced differential signaling, supports RS-485 and RS-422, and reaches 5 Mbit/s for high-speed local links. Use surge protection, common-mode protection, proper grounding, and a galvanic-isolation barrier when the connected cable leaves a controlled enclosure or crosses significant potential barriers.
How should I terminate and bias an ADM485ANZ bus?
Termination and biasing depend on the physical bus rather than on the transceiver alone. Add termination at the two physical ends of a long RS-485 cable, normally with a resistance value matched to the cable impedance, and provide fail-safe biasing so an idle bus remains in a defined logic state. For short, low-noise links, termination or biasing may be unnecessary, but the complete topology must be evaluated.
What design considerations matter for a 5 Mbit/s ADM485ANZ link?
A 5 Mbit/s ADM485ANZ link requires controlled impedance, closely coupled differential routing, a solid ground reference, and minimization of stubs. Keep the driver and receiver enable paths away from sensitive input traces, use a nearby supply bypass capacitor, and preserve the intended logic levels at every connector. Cable loss, reflections, common-mode voltage, and protection-device capacitance can all reduce the usable timing margin.
Where can I buy ADM485ANZ online?
Use the Request a Quote form on this page to request current ADM485ANZ availability, lead time, and order quantity from XAIPART. The manufacturer identifies the ADM485 family in 8-pin DIL and SOIC packages, while the ANZ ordering code denotes the leaded configuration used for this product. Confirm the exact suffix and package before submitting a purchase request.
What is the price and lead time of ADM485ANZ?
Current price and lead time for ADM485ANZ should be requested through the Request a Quote form on this page. The submitted request should identify the exact ADM485ANZ ordering code, required quantity, shipment destination, and whether reels, tubes, or another approved packing method is needed. This avoids basing an order on a changing distributor snapshot or an unsuitable package configuration.
Is ADM485ANZ currently in stock?
ADM485ANZ stock should be confirmed through the Request a Quote form on this page because inventory can change independently of the product's technical specifications. Include the required quantity and shipment location in the request. The exact ADM485ANZ suffix is important because other ADM485 package and temperature options may not be interchangeable with the selected leaded device.
What are the key specifications of ADM485ANZ that engineers should know?
The principal ADM485ANZ specifications are a 5 V supply, operation up to 5 Mbit/s, one differential transmitter with one differential receiver, support for EIA RS-485 and RS-422, and an 8-pin PDIP package. According to the Analog Devices ADM485 datasheet, the low-skew driver architecture is intended to minimize EMI interference. These characteristics define its suitability for high-speed balanced bus communication.
How does ADM485ANZ compare with ADM1485ANZ and SN75LBC184P?
ADM485ANZ, ADM1485ANZ, and SN75LBC184P are RS-485-family interface devices, but their electrical and timing characteristics must be compared rather than inferred from the protocol alone. The ADM485ANZ is rated for data rates up to 5 Mbit/s. According to the retrieved comparison references, all three are considered for replacement or comparison, so confirm pin behavior, enable polarity, propagation delay, and load capability in each manufacturer datasheet.

داتای سەرچاوەی ئەندازیاری بۆ ADM485ANZ — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.

ڕێنمایی هەڵبژاردن

Choose the ADM485ANZ for a 5 V, high-speed differential bus that must support RS-485 or RS-422 and requires a leaded 8-pin PDIP package. Its specified 5 Mbit/s rate and separate driver and receiver enables make it suitable for short industrial, instrumentation, and embedded links. Select ADM485JNZ when its ordering code and temperature grade match the system better; both retain the ADM485-family architecture and package footprint. Select ADM485ARZ after checking the exact qualification range because an ordering-code change can alter temperature coverage even when the electrical interface is similar.

Consider SN65LBC176P, SN65176BP, or SN75LBC184P when a cross-brand replacement is acceptable and the candidate's data rate, enable polarity, receiver thresholds, timing, and loading meet the design. A shared PDIP footprint is necessary but not sufficient for a true drop-in replacement. For new high-speed designs, prioritize the ADM485ANZ when its 5 Mbit/s specification provides useful timing margin. For long cables or low-rate field buses, confirm that cable loss and reflections permit operation at the selected baud rate. No candidate should be approved solely from package matching or protocol labeling.

بەراوردکردن لەگەڵ جێگرەوەکان

پارامەتر ئەم بەرهەمە ADM485JNZ ADM485ARZ SN65LBC176P SN65176BP SN75LBC184P
Package 8-pin PDIP 8-pin PDIP - same footprint 8-pin PDIP - same footprint 8-pin PDIP - same footprint 8-pin PDIP - same footprint 8-pin PDIP - same footprint
Brand Analog Devices Analog Devices Analog Devices Texas Instruments Texas Instruments Texas Instruments
Product Type RS-485/RS-422 differential transceiver RS-485/RS-422 differential transceiver RS-485/RS-422 differential transceiver Differential bus transceiver Differential bus transceiver Differential bus transceiver
Transmitter and Receiver Count 1 transmitter and 1 receiver 1 transmitter and 1 receiver 1 transmitter and 1 receiver 1 transmitter and 1 receiver 1 transmitter and 1 receiver 1 transmitter and 1 receiver
Supply Voltage 5 V 5 V 5 V 5 V 5 V 5 V
Communication Standards EIA RS-485 and RS-422 EIA RS-485 and RS-422 EIA RS-485 and RS-422 RS-485/RS-422 RS-485/RS-422 RS-485
Signal Polarity Balanced differential Balanced differential Balanced differential Balanced differential Balanced differential Balanced differential

جیاکەرەوە سەرەکییەکان

  • Higher supported bus rate than lower-rate legacy alternatives (بەراورد بەSN65LBC176P)
  • Direct same-family option preserves device functionality (بەراورد بەADM485JNZ)
  • Separate enable pins provide directional control (بەراورد بەSN75LBC184P)
  • Balanced differential implementation supports noise-resistant buses (بەراورد بەSN65176BP)

تێبینییەکانی دیزاین

Place the 5 V bypass capacitor immediately between VCC and GND, with its ground connection returning directly to the transceiver ground pin. Route A and B as a tightly coupled differential pair over a continuous reference plane. Keep the pair away from switching nodes and high-current return paths, minimize connector and test-point stubs, and avoid changing geometry between the transceiver and cable interface.

At the ADM485ANZ's maximum 5 Mbit/s rate, rise and fall times can be shorter than the bit period, so edge content becomes important. Use a cable and PCB impedance appropriate to the system, preserve controlled differential impedance, and check reflections at both physical bus ends. Do not add termination merely because the part is an RS-485 transceiver; short local links may operate correctly without it, while long cables usually require termination matched to the cable impedance.

Verify enable polarity and receiver-output behavior before replacing the ADM485ANZ. The DE and RE controls have opposite active states, so a board designed around one logic convention may behave incorrectly with another transceiver. Confirm the data rate, propagation delays, receiver thresholds, driver loading, fail-safe bias requirements, and temperature grade in the candidate datasheet rather than treating RS-485 protocol compliance as proof of interchangeability.

Differential signaling reduces susceptibility to common-mode noise, but imperfect A/B symmetry can convert interference into differential error. Keep the pair geometrically balanced through connectors and cable transitions, use a low-impedance chassis or signal ground according to the installation plan, and consider common-mode chokes or surge protection where field cables are exposed. Protection devices should be selected for low capacitance so they do not degrade a 5 Mbit/s edge.

زانیاری پابەندبوون

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
بێ قوڕقوشم
Unknown
بێ ھالۆجین
Unknown
کانزا ناکۆکەکان
Unknown

The retrieved manufacturer and distributor pages do not state the requested compliance details for this exact ordering code. Confirm RoHS, REACH, lead-free, halogen-free, and conflict-minerals status with the manufacturer before regulatory procurement.

داتا پشتڕاستکراوەتەوە لە: 2026-11-03 — داتا لەلایەن تیمی ئەندازیاری پێکھاتەکانی XAIPART پشتڕاستکراوەتەوە و ڕێکخراوە

گەڕانە پەیوەندیدارەکان

ADM485ANZ datasheet ADM485ANZ pinout ADM485ANZ datasheet pdf ADM485ANZ equivalent ADM485ANZ replacement ADM485ANZ cross reference ADM485ANZ vs SN65LBC176P ADM485ANZ vs SN65176BP ADM485ANZ price ADM485ANZ stock Analog Devices ADM485ANZ ADM485ANZ PDIP pinout ADM485ANZ RS-485 application circuit ADM485ANZ 5 Mbit/s

پێکهاتە و زاراوە پەیوەندیدارەکان

Analog Devices ADM485ANZ ADM485JNZ ADM485ARZ SN65LBC176P SN65176BP SN75LBC184P RS-485 RS-422 EIA RS-485 differential line transceiver differential bus transceiver interface IC communication interface semiconductor 5 Mbit/s 5 V 8-pin PDIP PDIP package through-hole package multipoint bus balanced differential signaling driver enable receiver enable
داواکاری نرخی خێرا RFQ
وردەکارییەکانی تەواو پڕ بکەرەوە — تیمی فرۆشتنی ئێمە لە ماوەی 24 کاتژمێردا وەڵام دەداتەوە
ژمارەی پارچە بەرهەمهێنەر پاکەت QTY نرخی ئامانج کۆی گشتی
✓
نرخەکە نێردرا!

لە ماوەی ٢٤ کاتژمێردا وەڵامی ئیمەیڵەکەت دەدەینەوە

1
داواکاری نرخ پێشکەشکرا
2
نرخپێدان وەرگیرا
3
داواکاری دانرا
4
پارەدان
5
نێردرا
6
گەیەنراوە
بینینی وردەکاریی داواکاری نرخ