Analog Devices

ADM485JN - 5V 5Mbps RS-485 Transceiver | Analog Devices

MPN: ADM485JN ✓ چالاک
+5 V Vdss EIA RS-485 and RS-422 Rds(on) 8-pin PDIP Package
MOQ: 1 |

ADM485JN گشتی

Analog Devices ADM485JN is a 5 V, low-power differential RS-485 and RS-422 transceiver capable of operation at data rates up to 5 Mbit/s, supplied in an 8-pin PDIP package. The device combines a differential line driver and a differential line receiver, supporting balanced transmission over multipoint bus systems. Its principal specifications include a single +5 V supply, a ±12 V bus common-mode range, 10 ns driver propagation delay, short-circuit protection, and thermal shutdown protection.

An RS-485 transceiver is an interface IC that converts logic-level signals into balanced differential signals for reliable communication over longer distances and noisy environments. It belongs to the EIA RS-485 and RS-422 interface hierarchy, where differential signaling improves noise immunity by comparing the voltage between two conductors rather than referencing the signal to ground. The ADM485JN supports both receiver and driver enable control, allowing a node to transmit, receive, or remain in a high-impedance state.

Key features include a maximum data rate of 5 Mbit/s, zero-skew driver propagation delay, and a +12 V bus common-mode range. These characteristics suit communication links where low signal distortion, high bus speed, or recovery from an electrical fault matters. The receiver and driver are independently enabled, supporting multidrop bus arrangements and designs in which a shared transceiver must avoid contending with other transmitters.

The BiCMOS implementation combines bipolar input and output characteristics with CMOS power efficiency. According to the Analog Devices product page, minimal driver propagation delay permits data rates up to 5 Mbit/s, while low skew minimizes EMI interference. The device also provides short-circuit protection and thermal shutdown, helping contain fault conditions when the bus driver drives into a low-impedance or shorted network.

Typical applications include industrial RS-485 buses, building-automation networks, instrumentation links, data acquisition systems, telecommunications equipment, and embedded serial networks. The balanced differential interface is particularly useful where cables run near motors, switching power supplies, or other sources of electromagnetic interference. Multi-drop communication requires careful termination, biasing, grounding, and node-enable sequencing to prevent multiple drivers from simultaneously driving the bus.

For implementation, place input and output bypassing capacitors close to the supply pins, use a proper termination network at each end of the bus, and verify the common-mode range under worst-case ground-potential differences. The 8-pin PDIP package facilitates through-hole construction and prototyping, although modern production designs may favor a smaller surface-mount package. Engineers should also confirm cable length, topology, data rate, and grounding against the system’s RS-485 implementation requirements.

This page combines verified manufacturer and distributor information with practical bus-design guidance, side-by-side replacement analysis, pin-package constraints, and application-focused engineering context. The comparisons and recommendations are limited to evidenced drop-in candidates so that PCB compatibility is not confused with merely similar functionality.

جێگرەوەکانی جێگۆڕکێ بۆ ADM485JN — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.

جۆرەکان لەم زنجیرەیەدا

مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ ADM485JN (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Package, Product Type, Standards Compliance, Supply Voltage, Temperature Range.

Analog Devices
Product Type: Differential RS-485/RS-422 line transceiver
Supply Voltage: 5 V
Temperature Range: Commercial and industrial
بەراوردکردن لەگەڵ ADM485JN →
Texas Instruments
Package: 8-pin PDIP (P)
Standards Compliance: ANSI TIA/EIA-422-B, TIA/EIA-485-A, ITU V.11, ITU X.27
بەراوردکردن لەگەڵ ADM485JN →

ADM485ANZ

✅ جێگرەوەی ڕاستەوخۆ
Analog Devices
📦 8-pin PDIP
Differential RS-485/RS-422 line transceiver · 5 V · 5 Mbit/s · 1 transmitter and 1 receiver · EIA RS-485 and RS-422 · Bidirectional multipoint bus · Balanced differential · 8-pin PDIP

پەیوەندی بۆ نرخ

بینینی داتاشیت →

ADM1485ANZ

✅ جێگرەوەی ڕاستەوخۆ
📦 8-pin PDIP
Related Analog Devices differential-transceiver candidate; exact enable logic, propagation delay, and common-mode limits require comparison against the ADM485 datasheet.

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

ST485CN

✅ جێگرەوەی ڕاستەوخۆ
📦 8-pin PDIP
Cross-brand RS-485 candidate identified in a direct ADM485JN comparison; enable polarity, electrical limits, and exact numbered pin assignments require final verification.

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

ADM485JN تایبەتمەندییەکان

Product Type RS-485/RS-422 differential line transceiver
ڤۆڵتیەی دابینکردن +5 V
Maximum Data Rate 5 Mbit/s
Bus Common-Mode Range +12 V
Driver Propagation Delay 10 ns
Driver Skew Zero skew
Driver and Receiver Enable Both driver and receiver can be enabled independently
Protection Short-circuit protection and thermal shutdown protection
Process Technology BiCMOS
Standards Compliance EIA RS-485 and RS-422
پاکێج 8-pin PDIP
جۆری دامەزراندن Through-hole
Temperature Range Commercial and industrial range

ڕێنمایی ڕێکخستنی پینی ADM485JN 8-pin pdip

ڕێکخستنی پین بۆ ADM485JN (پاکێجی 8-pin pdip). ژمارەدانی پین، فەنکشنەکان و نەخشەکانی پەیوەندی لە داتاشیتی بەرھەمھێنەردا پێناسە کراون. سەرنجی بدە بۆ شوێنپێی ورد و ڕێنمایییەکانی لەحیمکردن.

نەخشەی پینئاوتی پاکێجی 8-pin pdip بۆ ADM485JN

هیچ داتای وردی پینئاوت بەردەست نییە بۆ ADM485JN.

سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.

بەکارهێنانە باوەکان

ADM485JN گونجاوە بۆ 6 بەکارھێنانs: Industrial RS-485 Control Buses, Building Automation Networks, Data Acquisition and Instrumentation, Power and Energy Monitoring Systems, Telecommunications Equipment, Embedded Serial Networks.

🏭

Industrial RS-485 Control Buses

The ADM485JN fits industrial control and instrumentation buses that require balanced differential signaling at rates up to 5 Mbit/s. Its +5 V supply and independent driver and receiver enables support half-duplex communication between a controller and remote nodes. The 10 ns driver delay and zero-skew behavior can improve signal timing, although the complete design must still use bus termination, a fail-safe bias network, and common-mode protection. Ground offsets between cabinets should be evaluated against the +12 V common-mode range before deployment.

🧩

Building Automation Networks

ADM485JN is suitable for building-automation nodes using RS-485 for lighting, access control, HVAC, and environmental monitoring. Differential line signaling provides better noise immunity than single-ended communication, which is useful near relays, contactors, and switching loads. The device supports data rates up to 5 Mbit/s, allowing the bus speed to be matched to network length and transceiver enable timing. Production installations should include termination, biasing, surge protection, and consistent reference grounding between isolators or ground-translated nodes.

🔧

Data Acquisition and Instrumentation

The ADM485JN can connect laboratory or process instrumentation over an RS-485 network, providing a common differential interface for distributed measurements. Its low 10 ns driver propagation delay and zero driver skew support predictable signaling at rates up to 5 Mbit/s. The independent receiver and driver enables are useful when multiple devices share a multidrop bus and must avoid simultaneous transmission. Designers should verify the common-mode voltage under ground-potential differences and isolate the bus when long cables cross between buildings or high-energy equipment.

⚡

Power and Energy Monitoring Systems

ADM485JN is appropriate for power-monitoring equipment that distributes measurements from meters, inverters, or environmental sensors over an RS-485 network. The balanced bus reduces susceptibility to common-mode noise found in industrial power systems, while the +12 V common-mode range provides tolerance for moderate ground offsets. Its 5 Mbit/s capability permits faster polling than many low-speed field buses. The designer should nevertheless add surge and ESD protection, especially where the cable leaves a control enclosure or crosses between buildings.

🌐

Telecommunications Equipment

The ADM485JN can support internal RS-485 links in telecommunications equipment, including status, alarm, and supervisory communication between rack-mounted modules. Its 8-pin PDIP package is straightforward to inspect and prototype, while independent enables allow a node to receive continuously and transmit only when selected. The low driver delay and zero skew aid timing at data rates up to 5 Mbit/s. Equipment designers should account for conducted emissions, chassis grounding, and protection from external wiring faults.

📱

Embedded Serial Networks

ADM485JN is useful for embedded systems that add an RS-485 port to a controller, sensor hub, or actuator gateway. The receiver and driver can be enabled separately, allowing half-duplex firmware to transition between listening and transmitting without contending on the bus. The 5 Mbit/s maximum provides headroom for short, high-throughput links, while the +12 V common-mode range helps with imperfect ground references. Firmware and hardware must coordinate driver-enable timing to prevent two nodes from transmitting simultaneously.

What are the key specifications of ADM485JN that engineers should know?
The ADM485JN is a 5 V RS-485/RS-422 transceiver operating up to 5 Mbit/s in an 8-pin PDIP package. According to the Analog Devices datasheet, it provides a +12 V bus common-mode range, 10 ns driver propagation delay, zero driver skew, short-circuit protection, and thermal shutdown protection. Its differential driver and receiver can be enabled independently, making the device suitable for half-duplex multidrop buses. These are the principal parameters to evaluate against bus topology, cable length, grounding, and fault-current requirements.
What is the operating voltage of ADM485JN?
The ADM485JN operates from a single +5 V supply. The Analog Devices datasheet identifies the part as a 5 V low-power EIA RS-485 transceiver and lists +12 V as the bus common-mode range, which describes the allowable voltage range on the bus relative to the transceiver’s ground reference. The supply requirement and common-mode limit are distinct: a valid +5 V supply does not remove the need to control ground offsets between connected nodes.
What is the maximum data rate of ADM485JN?
The ADM485JN supports data rates up to 5 Mbit/s. The Analog Devices product page states that minimal driver propagation delay permits transmission at 5 Mbit/s, while the datasheet identifies zero-skew driver propagation as a feature that helps minimize EMI interference. In practice, the complete bus must also support the selected rate; cable length, topology, termination, transceiver enable timing, and grounding can reduce the usable margin on long installations.
Where can I download the ADM485JN datasheet PDF?
The official ADM485JN datasheet PDF is available from Analog Devices at https://www.analog.com/media/en/technical-documentation/data-sheets/ADM485.pdf. The document is titled “5 V Low Power EIA RS-485 Transceiver Data Sheet” and provides the manufacturer’s electrical characteristics, application information, and package details. Use the manufacturer copy for design verification because distributor-hosted copies may reflect different revisions or provide less complete search metadata.
Where can I find the ADM485JN pinout?
The ADM485JN pinout is shown in the Analog Devices ADM485 datasheet, while DigiKey identifies the device as an 8-PDIP RS-422/RS-485 transceiver. The provided source material confirms the eight-pin PDIP package but does not reproduce a numbered pin table, so an exact numbered pinout cannot be transcribed without risking an incorrect connection. Follow the official datasheet for DE, RE, driver-output, receiver-input, supply, and ground assignments before constructing a board.
Is ADM485JN suitable for industrial RS-485 communication?
The ADM485JN is suitable for industrial RS-485 communication when the bus meets its electrical and thermal limits. The Analog Devices product page states that the device is fully specified over the commercial and industrial temperature range, while the datasheet identifies independent driver and receiver enables, a 5 Mbit/s rate, and a +12 V bus common-mode range. Industrial suitability still depends on grounding, surge protection, cable selection, and proper termination.
What can replace ADM485JN without changing the 8-pin PDIP PCB footprint?
ADM485JN can be replaced only after confirming that the candidate has the same 8-pin PDIP footprint, pin functions, supply requirements, enable logic, and compatible electrical limits. The supplied cross-reference evidence identifies ADM485ANZ and ADM1485ANZ as related comparison candidates and specifically discusses ADM485JN versus ST485CN. Because the verified material does not establish five fully documented drop-ins, fewer than five alternatives are listed rather than padding the list with unverified parts.
Is ADM485JN the same as ADM485ANZ?
ADM485JN and ADM485ANZ are closely related Analog Devices versions, but the suffix identifies different package options and therefore may require different PCB layouts. The verified comparison search explicitly identifies ADM485ANZ versus ADM485JN and discusses package type as a difference. Before substitution, confirm that the replacement really is an 8-pin PDIP variant and compare the complete manufacturer pinout rather than relying on the base ADM485 family name.
ADM485JN vs ST485CN - which is better for a new RS-485 design?
ADM485JN and ST485CN are both RS-485 transceivers, but the supplied comparison evidence does not provide enough verified operating, logic, or package data to declare a universal winner. The ADM485JN is specifically confirmed as an 8-pin PDIP device operating from 5 V at up to 5 Mbit/s. Choose it when maintaining the existing Analog Devices footprint is important; evaluate ST485CN only after verifying its exact pinout, enable polarity, limits, and lifecycle requirements.
When should I choose ADM485JN over another RS-485 transceiver?
Choose ADM485JN when the design requires an 8-pin PDIP RS-485/RS-422 transceiver with a 5 V supply, operation up to 5 Mbit/s, independent driver and receiver enables, and existing Analog Devices board compatibility. The +12 V bus common-mode range can also help accommodate ground-potential variation, although it does not replace proper grounding or surge protection. A smaller surface-mount or automotive-qualified alternative may be preferable for a new compact design.
What is the best Analog Devices equivalent for ADM485JN?
ADM485ANZ is the closest explicitly compared Analog Devices alternative in the supplied cross-reference material, but its suffix and package must be checked before substitution. ADM1485ANZ is another related Analog Devices comparison candidate. Neither candidate is presented here as guaranteed drop-in because the verified excerpts do not show complete numbered pinouts and electrical tables. For an unchanged 8-pin PDIP board, the original ADM485JN remains the best-supported selection.
Where to buy ADM485JN online?
ADM485JN is available from major electronics distributors, including DigiKey and Mouser. DigiKey lists the Analog Devices ADM485JN as a 1/1 half-duplex RS-422/RS-485 transceiver in an 8-PDIP package, while Mouser lists it as an RS-422/RS-485 interface IC. The supplied results do not include current numeric prices or confirmed XAIPART inventory, so request a quotation before ordering and verify stock, lead time, and suffix-specific packaging at the distributor.
What is the price of ADM485JN?
The current numeric price of ADM485JN was not included in the verified source data. Digikey and Mouser product pages provide live purchasing information, but the retrieved excerpts do not expose a price that can be reproduced here. Pricing is therefore shown as a zero placeholder in the quantity tiers and should not be interpreted as a free offer. Obtain the current price as of 2026-10-28 directly from the distributor or request a quote from XAIPART.
What is the lead time for ADM485JN and is it in stock?
The verified Digikey excerpt says “Buy now, ships today” for ADM485JN, but it does not provide a numeric lead time or a guaranteed XAIPART stock quantity. Digikey inventory changes by order date and quantity, while Mouser and Octopart can offer separate availability. Confirm the current quantity and lead time as of 2026-10-28 before committing the design to a production schedule, especially for larger builds.
Does ADM485JN provide short-circuit and thermal protection?
The ADM485JN datasheet lists short-circuit protection and thermal shutdown protection. These protections improve robustness when the driver encounters an abnormal bus condition, but they do not make external surge protection unnecessary. The external bus still needs appropriate protection for electrostatic discharge, lightning-induced transients, and industrial switching events, selected according to the installation’s isolation and grounding requirements.

داتای سەرچاوەی ئەندازیاری بۆ ADM485JN — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.

ڕێنمایی هەڵبژاردن

Choose ADM485JN when maintaining an existing Analog Devices 8-pin PDIP design, supporting RS-485 and RS-422 links at up to 5 Mbit/s, or retaining the documented 10 ns driver delay, zero skew, short-circuit protection, and thermal shutdown features. ADM485ANZ is the closest explicitly compared Analog Devices candidate, but its package suffix must be checked before substitution. ADM1485ANZ may suit related differential-interface requirements after its complete pinout and timing data are compared with ADM485JN. ST485CN is a viable cross-brand review candidate for a new design, but it should be selected only after confirming its pin compatibility, enable polarity, common-mode range, protection, and lifecycle status. For any substitution, verify the official datasheet, PCB footprint, termination network, and bus timing rather than relying solely on the RS-485 label.

بەراوردکردن لەگەڵ جێگرەوەکان

پارامەتر ئەم بەرهەمە ADM485ANZ ADM1485ANZ ST485CN
Package 8-pin PDIP 8-pin PDIP 8-pin PDIP 8-pin PDIP
Brand Analog Devices Analog Devices Analog Devices STMicroelectronics
Product Type RS-485/RS-422 differential transceiver RS-485/RS-422 differential transceiver RS-485-family differential transceiver RS-485 transceiver

جیاکەرەوە سەرەکییەکان

  • Documented high-speed operation (بەراورد بەADM1485ANZ)
  • Specified driver timing and skew (بەراورد بەST485CN)
  • Integrated fault-oriented protection (بەراورد بەADM485ANZ)

تێبینییەکانی دیزاین

Do not enable the driver on more than one node at the same time. The ADM485JN supports independent driver and receiver control, but overlapping transmissions can create conflicting bus states, excess current, and unreliable data. In firmware, use a single bus arbiter, account for enable and propagation delays, and guarantee a turnaround interval before another node drives the line.

Route the differential pair as a tightly coupled pair with continuous reference geometry, minimize stubs, and keep the transceiver close to the connector. Place supply bypassing at the IC pins and provide a clear return path. Although the exact capacitor values are not established by the supplied data, the manufacturer’s recommended schematic and layout should be followed for the selected board revision.

Use termination only at the two physical ends of the bus and install a fail-safe bias network at one suitable location. Avoid placing multiple termination networks on a multidrop network, because parallel termination can over-damp the bus and impair signal quality. The zero-skew driver characteristic helps reduce EMI, but cable routing, common-mode behavior, and connector shielding remain important.

The +12 V bus common-mode rating is not a substitute for a protected power rail or ground design. Verify the maximum voltage seen by every transceiver pin under startup, ground-offset, and fault conditions, especially when nodes communicate through long cables. Add appropriately rated surge and ESD protection where exposed cables connect the board to external equipment.

زانیاری پابەندبوون

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
بێ قوڕقوشم
Unknown
بێ ھالۆجین
Unknown
کانزا ناکۆکەکان
Unknown

The supplied search excerpts compare RoHS and REACH attributes but do not provide an unambiguous compliance statement for ADM485JN. The device is an industrial interface IC, but no AEC-Q100 qualification is identified in the verified data.

داتا پشتڕاستکراوەتەوە لە: 2026-10-28 — داتا لەلایەن تیمی ئەندازیاری پێکھاتەکانی XAIPART پشتڕاستکراوەتەوە و ڕێکخراوە

گەڕانە پەیوەندیدارەکان

ADM485JN ADM485JN datasheet Analog Devices ADM485JN ADM485JN 5Mbit/s RS-485 transceiver ADM485JN 8-pin PDIP ADM485JN industrial RS-485 bus ADM485JN vs ST485CN ADM485JN drop-in replacement ADM485JN buy price ADM485JN pinout ADM485JN lead time and stock 5V low power EIA RS-485 transceiver

پێکهاتە و زاراوە پەیوەندیدارەکان

Analog Devices ADM485JN ADM485ANZ ADM1485ANZ ST485CN RS-485 transceiver RS-422 transceiver differential line transceiver interface IC semiconductor balanced differential signaling multipoint bus EIA RS-485 EIA RS-422 BiCMOS 8-pin PDIP DIP package through-hole package industrial automation building automation data acquisition power monitoring telecommunications equipment driver propagation delay bus common-mode range
داواکاری نرخی خێرا RFQ
وردەکارییەکانی تەواو پڕ بکەرەوە — تیمی فرۆشتنی ئێمە لە ماوەی 24 کاتژمێردا وەڵام دەداتەوە
ژمارەی پارچە بەرهەمهێنەر پاکەت QTY نرخی ئامانج کۆی گشتی
✓
نرخەکە نێردرا!

لە ماوەی ٢٤ کاتژمێردا وەڵامی ئیمەیڵەکەت دەدەینەوە

1
داواکاری نرخ پێشکەشکرا
2
نرخپێدان وەرگیرا
3
داواکاری دانرا
4
پارەدان
5
نێردرا
6
گەیەنراوە
بینینی وردەکاریی داواکاری نرخ