Analog Devices

ADM488ANZ - 250 kbps RS-485 Transceiver | Analog Devices

MPN: ADM488ANZ ✓ چالاک
4.5 V to 5.5 V Vdss 8-PDIP (0.300 inch, 7.62 mm pitch) Package
MOQ: 1 |

ADM488ANZ گشتی

The Analog Devices ADM488ANZ is a 5 V, full-duplex RS-422/RS-485 interface transceiver with one driver and one receiver, a 250 kbps data rate, and an 8-pin PDIP package. Its supply-voltage range is 4.5 V to 5.5 V, making it suitable for conventional 5 V industrial, instrumentation, and embedded communications systems.

An RS-485 transceiver is an interface IC that combines a differential line driver and differential receiver on a communications bus. In the hierarchy of electronic components, the ADM488ANZ is a line-interface transceiver, a type of interface IC and semiconductor. RS-422 supports point-to-point differential signaling, while RS-485 supports multipoint buses with more stringent driver-enable and grounding considerations. The ADM488ANZ can address both applications in one 8-pin device.

The ADM488ANZ provides a 250 kbps maximum data rate, low-power operation, and slew-rate-limited outputs. Full duplex permits simultaneous transmission and reception, unlike half-duplex transceivers that require a shared driver and receiver bus. The 4.5 V to 5.5 V operating range also simplifies connection to 5 V digital logic when its interface levels are compatible with the host device.

According to the Analog Devices manufacturer datasheet, the ADM488ANZ meets EIA RS-485 and RS-422 standards. The device uses a differential data path to support noise-resistant communications over cables and longer interconnects. Its slew-rate-limited driver helps control the transition rate on the bus, reducing high-frequency EMI compared with an unrestricted driver while maintaining a useful 250 kbps operating rate.

Typical uses include industrial control links, laboratory instrumentation, building automation, data-acquisition systems, and embedded equipment requiring full-duplex RS-422 or RS-485 communication. The device can also participate in networks using protocol converters, sensor interfaces, or remote monitoring units. Its 8-pin PDIP package favors through-hole construction and easy prototype replacement rather than high-density automated assembly.

For reliable bus operation, confirm the cable length, topology, termination strategy, grounding method, and driver-enable behavior for the selected protocol. Keep differential traces closely coupled where practical, route the pair away from switching nodes and high-current paths, and follow the manufacturer pin-description table when making PCB assignments. Do not assume that a full-duplex RS-422 connection can be replaced directly with a half-duplex RS-485 topology.

This page combines the ADM488ANZ device specifications, package information, sourcing guidance, comparison criteria, and practical interface-design notes. It helps engineers distinguish protocol, speed, package, and bus-topology differences before selecting a replacement or laying out a new communication interface.

جێگرەوەکانی جێگۆڕکێ بۆ ADM488ANZ — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.

جۆرەکان لەم زنجیرەیەدا

مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ ADM488ANZ (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Product Type, Mounting Type, Package, Supply Voltage, Data Rate.

Analog Devices
Product Type: RS-422/RS-485 differential line transceiver
Mounting Type: Surface mount
Package: 8-pin MSOP
بەراوردکردن لەگەڵ ADM488ANZ →
Analog Devices
Product Type: Full-duplex differential RS-485/RS-422 transceiver
Mounting Type: Through-hole
Package: 8-pin PDIP
بەراوردکردن لەگەڵ ADM488ANZ →
Analog Devices
Product Type: RS-485/RS-422 transceiver
Mounting Type: Through-hole
Package: 8-pin PDIP
بەراوردکردن لەگەڵ ADM488ANZ →

MAX488EEPA+

✅ جێگرەوەی ڕاستەوخۆ
📦 8-PDIP (0.300 inch, 7.62 mm pitch)
Same 8-pin PDIP RS-485/RS-422 transceiver format; the alternative is identified by ±15 kV ESD protection, while the ADM488ANZ is specified at 250 kbps. Complete quantified electrical differences are .

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

ADM488ANZ تایبەتمەندییەکان

Product Type Full-duplex differential transceiver
Supported Protocols EIA RS-422 and EIA RS-485
Number of Drivers 1 driver
Number of Receivers 1 receiver
Maximum Data Rate 250 kbps
Supply Voltage Range 4.5 V to 5.5 V
Operating Mode Full duplex
Driver Output Characteristics Slew-rate limited
Power Class Low power
پاکێج 8-PDIP (0.300 inch, 7.62 mm pitch)
جۆری دامەزراندن Through-hole PDIP
Packaging Tube

ڕێنمایی ڕێکخستنی پینی ADM488ANZ 8-pdip (0.300 inch, 7.62 mm pitch)

ڕێکخستنی پین بۆ ADM488ANZ (پاکێجی 8-pdip (0.300 inch, 7.62 mm pitch)). ژمارەدانی پین، فەنکشنەکان و نەخشەکانی پەیوەندی لە داتاشیتی بەرھەمھێنەردا پێناسە کراون. سەرنجی بدە بۆ شوێنپێی ورد و ڕێنمایییەکانی لەحیمکردن.

نەخشەی پینئاوتی پاکێجی 8-pdip (0.300 inch, 7.62 mm pitch) بۆ ADM488ANZ

هیچ داتای وردی پینئاوت بەردەست نییە بۆ ADM488ANZ.

سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.

بەکارهێنانە باوەکان

ADM488ANZ گونجاوە بۆ 6 بەکارھێنانs: Industrial Control and Automation Links, Laboratory Instrumentation, Data-Acquisition and Sensor Networks, Building Automation Equipment, Embedded Equipment Communication, Remote Monitoring and Telemetry.

🏭

Industrial Control and Automation Links

The ADM488ANZ fits point-to-point industrial control links that require full-duplex differential signaling at rates up to 250 kbps. Its 4.5 V to 5.5 V supply range supports conventional 5 V control electronics, while the slew-rate-limited driver helps control bus-edge energy. The device is placed between the host controller and a dedicated RS-422 pair or a full-duplex RS-485 network. Engineers must still verify common-mode range, grounding, cable length, and isolation requirements for the installation environment.

🔧

Laboratory Instrumentation

Laboratory instruments often distribute measurement commands and results over long, noisy cable runs. The ADM488ANZ provides a full-duplex differential link with one driver, one receiver, and a maximum rate of 250 kbps, allowing status information to be returned while commands are transmitted. Place the transceiver at the instrument's interface connector and keep the differential pair routed together. For benchtop systems requiring galvanic isolation, evaluate the interface protection and isolation architecture separately.

📡

Data-Acquisition and Sensor Networks

The ADM488ANZ is suitable for full-duplex sensor and data-acquisition links operating below 250 kbps. Differential signaling reduces susceptibility to common-mode interference compared with single-ended communication, while full duplex permits simultaneous sensor commands and measurements. Its 5 V operating range can support embedded acquisition hardware without a separate high-voltage transceiver supply. Designers should calculate cable loss and noise margin, apply termination where required, and confirm that all connected nodes use compatible polarity and grounding.

🏠

Building Automation Equipment

Building controllers, floor modules, and remote I/O units can use the ADM488ANZ for full-duplex RS-422 or RS-485 supervisory links. The 250 kbps maximum data rate is suitable for command exchange and status reporting rather than high-volume streaming. Its low-power, slew-rate-limited transceiver architecture supports robust wired communication in electrically noisy buildings. Field designs should provide consistent reference ground, avoid routing bus pairs alongside motor and lighting wiring, and use surge protection appropriate to the installation environment.

🖥️

Embedded Equipment Communication

The ADM488ANZ connects a microcontroller, DSP, or other digital controller to a full-duplex RS-422 or RS-485 peripheral at up to 250 kbps. Its 4.5 V to 5.5 V operating range suits 5 V embedded systems, and the 8-pin PDIP package simplifies prototyping and replacement. Place the transceiver close to the external connector, route the differential signals as a pair, and connect the transceiver ground thoughtfully to the cabinet or board ground. Signal-level compatibility with the host controller must be checked before layout release.

📡

Remote Monitoring and Telemetry

Remote monitoring stations can use the ADM488ANZ for full-duplex command and telemetry paths at rates up to 250 kbps. Differential signaling and controlled output transitions improve robustness in installations containing relays, motors, and switching power converters. Use one dedicated differential pair for transmission and another for reception, and terminate buses according to the selected standard and topology. For installations crossing buildings or industrial boundaries, isolation and surge protection should be evaluated as part of the complete interface design.

What is the ADM488ANZ?
The ADM488ANZ is a 5 V, full-duplex EIA RS-422/RS-485 differential transceiver from Analog Devices. It contains one driver and one receiver, supports data rates up to 250 kbps, and is packaged in an 8-pin PDIP. According to the Analog Devices manufacturer datasheet, its low-power, slew-rate-limited design is intended for reliable differential data communications.
What are the key specifications of ADM488ANZ that engineers should know?
The ADM488ANZ operates from 4.5 V to 5.5 V and provides one differential driver and one receiver in a full-duplex configuration. Its maximum signaling rate is 250 kbps. According to the Analog Devices manufacturer datasheet, the device supports EIA RS-422 and RS-485, uses slew-rate-limited outputs, is offered in an 8-pin PDIP, and is supplied in tube packaging.
Where can I download the ADM488ANZ datasheet PDF?
The ADM488ANZ datasheet PDF is available directly from Analog Devices at the official document link on this page. According to the Analog Devices manufacturer documentation, the document covers the ADM488 and ADM489 family, including RS-485/RS-422 operation, supply requirements, electrical characteristics, and application information. Use the manufacturer's pin-description table when assigning PCB signals.
Where can I find the ADM488ANZ pinout?
Use the Analog Devices ADM488_489 manufacturer datasheet to locate the ADM488ANZ pin-description table and package drawing. The device uses an 8-pin PDIP configuration with the standard top-left orientation for pin 1. Verify signal names, enable behavior, and ground assignments against the current datasheet before laying out or modifying a board.
What is the maximum data rate of ADM488ANZ?
The ADM488ANZ supports a maximum data rate of 250 kbps. According to the Analog Devices manufacturer datasheet, the transceiver also provides slew-rate-limited outputs for improved control of bus-edge energy. The usable application rate can be lower when determined by cable length, topology, termination, noise, and the timing requirements of the connected system.
What supply voltage does ADM488ANZ require?
The ADM488ANZ requires a 4.5 V to 5.5 V supply. According to the Analog Devices manufacturer datasheet, this operating range is appropriate for conventional 5 V interface systems. Confirm the host transceiver's supply level, signal thresholds, and ground reference before connecting the device to a microcontroller, DSP, or programmable logic controller.
Is ADM488ANZ full duplex or half duplex?
The ADM488ANZ is a full-duplex transceiver. It includes one driver and one receiver, allowing transmission and reception to use separate differential pairs. According to the Analog Devices manufacturer datasheet, this differs from half-duplex RS-485 arrangements where the driver and receiver share a bus. A replacement must preserve the intended bus topology.
Where can I buy ADM488ANZ online?
Use the Request a Quote form on this page to ask about ADM488ANZ availability, current lead time, and order handling. The Analog Devices product page identifies the ADM488 family as being in production, while authorized inventory information for the exact ADM488ANZ ordering code is published by multiple channels. XAIPART does not publish a static price that could become stale.
What is the price of ADM488ANZ?
The current ADM488ANZ price is returned through the Request a Quote form on this page rather than as a static figure. Price can vary with order quantity, delivery date, and supply status, so a current quotation is more useful than a historical price. The manufacturer product page also states that its list-price information is unavailable.
What is the lead time for ADM488ANZ?
Request the current ADM488ANZ lead time and minimum order quantity through the Request a Quote form on this page. Lead time depends on the chosen quantity, package form, and current manufacturer or authorized-channel inventory. The Analog Devices product page identifies the ADM488 family as being in production, but it does not state a fixed order lead time.
Is ADM488ANZ in stock?
ADM488ANZ stock status should be confirmed through the Request a Quote form on this page for the intended quantity and delivery date. The Analog Devices product page lists the ADM488 family in production, while the exact ADM488ANZ inventory varies among distribution channels. Submit the desired order quantity so the quotation can reflect current supply.
What is the difference between ADM488ANZ and MAX488EEPA+?
Both devices are described as low-power, slew-rate-limited RS-485/RS-422 transceivers, and both use an 8-pin PDIP form. The ADM488ANZ is specified at 250 kbps. According to the MAX488EEPA+ product description used in the comparison source, its distinguishing feature is ±15 kV ESD protection; complete side-by-side electrical limits should be checked before substitution.
When should I choose ADM488ANZ over MAX488EEPA+?
Choose the ADM488ANZ when a 250 kbps full-duplex RS-422/RS-485 interface in an 8-pin PDIP is the required baseline. Consider the MAX488EEPA+ when its specified ESD protection level is important for the installation environment. According to the relevant manufacturer documentation, both use low-power, slew-rate-limited transceivers, but the complete electrical and protection ratings must be compared.
What can replace ADM488ANZ?
The MAX488EEPA+ is the closest verified drop-in candidate identified for the ADM488ANZ because both are 8-pin PDIP RS-485/RS-422 transceivers. However, the ADM488ANZ is rated for 250 kbps and supports full duplex, so a replacement should be checked for data rate, driver enable, fail-safe behavior, ESD rating, and exact pin mapping before it is approved.
Is ADM488ANZ suitable for industrial RS-485 equipment?
The ADM488ANZ is suitable for many 5 V industrial RS-422 and RS-485 interfaces that operate at or below 250 kbps. According to the Analog Devices manufacturer datasheet, it supports EIA RS-485 and RS-422 with slew-rate-limited, low-power operation. Industrial suitability still depends on temperature range, isolation, surge protection, grounding, and the certification requirements of the complete equipment.

داتای سەرچاوەی ئەندازیاری بۆ ADM488ANZ — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.

ڕێنمایی هەڵبژاردن

Choose the ADM488ANZ when the design requires a full-duplex, 5 V EIA RS-422/RS-485 transceiver in an 8-pin PDIP and can operate at up to 250 kbps. Its separate driver and receiver paths suit point-to-point links and full-duplex network arrangements. Consider the MAX488EEPA+ when its identified ±15 kV ESD protection is important and its complete electrical ratings match the design; confirm data rate, enable behavior, fail-safe response, temperature range, and exact pin mapping before substitution. Do not select a half-duplex RS-485 part as a drop-in replacement unless the wiring and control logic are redesigned. For industrial or long-cable installations, also evaluate isolation, surge protection, common-mode range, grounding, and connector requirements, since these interface protections are separate from the basic transceiver choice.

بەراوردکردن لەگەڵ جێگرەوەکان

پارامەتر ئەم بەرهەمە MAX488EEPA+
Package 8-PDIP (0.300 inch, 7.62 mm pitch) 8-pin PDIP
Brand Analog Devices Maxim Integrated
Supported Protocols EIA RS-422 and RS-485 RS-485/RS-422
Output Slew Control Slew-rate limited Slew-rate limited

جیاکەرەوە سەرەکییەکان

  • Full-duplex interface with separate communication paths (بەراورد بەMAX488EEPA+)
  • Established EIA RS-422 and RS-485 support (بەراورد بەMAX488EEPA+)
  • 5 V supply operation (بەراورد بەMAX488EEPA+)

تێبینییەکانی دیزاین

Route each differential pair as a tightly coupled pair and keep the driver and receiver paths away from switching nodes, inductors, relay contacts, and high-current return paths. Place the transceiver close to the external connector when ESD or surge exposure is significant, while observing the datasheet's recommended component-placement and grounding guidance. Maintain consistent ground references between connected equipment.

Treat the bus as a transmission line when cable length, rise time, or topology makes reflections significant. Apply the termination method required by the selected RS-422 or RS-485 configuration, and verify receiver thresholds across cable length, node count, temperature, and tolerance. The 250 kbps limit describes the device's signaling rate, but the complete system rate must also satisfy protocol timing and propagation delay.

Do not substitute a half-duplex transceiver without redesigning the bus wiring and driver-enable logic. The ADM488ANZ is a full-duplex device with separate transmit and receive paths, whereas many RS-485 alternatives share a bus. Also verify package orientation and every pin assignment from the manufacturer pin-description table; an 8-pin PDIP footprint alone does not guarantee functional equivalence.

Use controlled-rise-time driver outputs and avoid adding unnecessary edge-shaping networks that could degrade the intended 250 kbps operation. Keep cable routing away from switching power-converter loops and route chassis or cable-shield connections according to the equipment's grounding architecture. For installations crossing between buildings or long industrial cable runs, add suitable isolation and surge-protection circuitry beyond the transceiver's basic interface function.

زانیاری پابەندبوون

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
بێ قوڕقوشم
Unknown
بێ ھالۆجین
Unknown
کانزا ناکۆکەکان
Unknown

The manufacturer product page identifies the ADM488 family as being in production, but the cited product information does not explicitly state the requested compliance statuses.

داتا پشتڕاستکراوەتەوە لە: 2026-11-03 — داتا لەلایەن تیمی ئەندازیاری پێکھاتەکانی XAIPART پشتڕاستکراوەتەوە و ڕێکخراوە

گەڕانە پەیوەندیدارەکان

ADM488ANZ datasheet ADM488ANZ datasheet pdf ADM488ANZ pinout ADM488ANZ equivalent ADM488ANZ replacement ADM488ANZ price ADM488ANZ stock Analog Devices ADM488ANZ ADM488ANZ 250 kbps transceiver ADM488ANZ 8-PDIP ADM488ANZ RS-485 interface ADM488ANZ vs MAX488EEPA+ ADM488ANZ application circuit ADM488ANZ full duplex interface

پێکهاتە و زاراوە پەیوەندیدارەکان

Analog Devices ADM488ANZ ADM488 ADM489 MAX488EEPA+ RS-485 RS-422 EIA RS-485 EIA RS-422 differential transceiver interface IC semiconductor full duplex slew-rate-limited driver differential line driver differential receiver 250 kbps data rate 4.5 V to 5.5 V supply 8-PDIP through-hole package surface mount industrial control data acquisition building automation telemetry
داواکاری نرخی خێرا RFQ
وردەکارییەکانی تەواو پڕ بکەرەوە — تیمی فرۆشتنی ئێمە لە ماوەی 24 کاتژمێردا وەڵام دەداتەوە
ژمارەی پارچە بەرهەمهێنەر پاکەت QTY نرخی ئامانج کۆی گشتی
✓
نرخەکە نێردرا!

لە ماوەی ٢٤ کاتژمێردا وەڵامی ئیمەیڵەکەت دەدەینەوە

1
داواکاری نرخ پێشکەشکرا
2
نرخپێدان وەرگیرا
3
داواکاری دانرا
4
پارەدان
5
نێردرا
6
گەیەنراوە
بینینی وردەکاریی داواکاری نرخ