MaxLinear

SP490ECP-L - 10Mbps Full-Duplex RS-485 IC | MaxLinear

MPN: SP490ECP-L ✗ کۆتایی ژیان
5 V Vdss 0.9 mA Id RS-485 and RS-422 Rds(on) 8-PDIP (0.300 inch, 7.62 mm pitch) Package
MOQ: 1 |

SP490ECP-L گشتی

The MaxLinear, Inc. SP490ECP-L is a 10 Mbps full-duplex RS-485/RS-422 differential line transceiver packaged in an 8-pin PDIP package. It combines one differential driver and one differential receiver, supports +5 V-only operation, and is intended for bidirectional serial data links that require simultaneous transmitting and receiving. The SP490E family is specified for operation at data rates up to 10 Mbps.

An RS-485 transceiver is a physical-layer interface IC that converts logic-level signals into balanced differential signals for reliable communication over longer distances and in electrically noisy environments. Related classifications include differential line transceiver, communications interface IC, and interface IC. The SP490ECP-L supports both RS-485 and RS-422 applications while providing a +200 mV receiver input sensitivity and a wide common-mode range.

The SP490E family is designed for low-power +5 V operation. Its single transmitter and single receiver support full-duplex links, while the SP490E family's differential signaling helps reject common-mode noise. The product is available in through-hole 8-pin PDIP packaging, which is useful for legacy industrial, telecommunications, instrumentation, and control equipment where surface-mount assembly is not required.

According to the manufacturer product page, the SP490E meets RS-485 and RS-422 standards at speeds up to 10 Mbps. The receiver's stated sensitivity of ±200 mV defines the differential input range around which the receiver recognizes signaling states, while the wide common-mode range helps preserve operation where the two conductors experience voltage offsets relative to the local ground reference.

Typical uses include industrial RS-485 buses, point-to-point RS-422 links, process-control equipment, data acquisition systems, and legacy communications equipment. Unlike a half-duplex transceiver, the full-duplex architecture can transmit and receive concurrently when the interface is wired with separate differential pairs, simplifying timing in applications that cannot stop receiving while the transmitter is active.

The primary design consideration is that the 8-pin PDIP footprint does not itself guarantee interoperability with every RS-485 transceiver. Before substitution, engineers should verify pin assignments, driver and receiver enable behavior, supply requirements, common-mode limits, fail-safe response, and bus termination against the manufacturer datasheet and the original board schematic.

This page consolidates verified distributor specifications, lifecycle information, pin-compatible alternatives, and application-oriented design guidance. It adds practical selection context beyond a distributor listing while keeping unverified electrical values clearly separated from the supplied source data.

جێگرەوەکانی جێگۆڕکێ بۆ SP490ECP-L — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.

جۆرەکان لەم زنجیرەیەدا

مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ SP490ECP-L (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Package, Mounting Type, Maximum Data Rate, Product Type, Number of Receivers.

MaxLinear
Package: 8-pin SOIC
Maximum Data Rate: 5 Mbps
Product Type: RS-485/RS-422 differential line transceiver
بەراوردکردن لەگەڵ SP490ECP-L →
Maxim Integrated
Package: 8-pin plastic DIP
Mounting Type: Through-hole
Maximum Data Rate: 5 Mbps
بەراوردکردن لەگەڵ SP490ECP-L →
MaxLinear
Package: 8-pin narrow SOIC
Mounting Type: Surface mount
Maximum Data Rate: 5 Mbps
بەراوردکردن لەگەڵ SP490ECP-L →

SP490ECP

✅ جێگرەوەی ڕاستەوخۆ
📦 8-PDIP
Same SP490E family and 10 Mbps full-duplex function; suffix-specific lifecycle and temperature details require datasheet confirmation.

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

SP490EN-L

✅ جێگرەوەی ڕاستەوخۆ
MaxLinear
📦 8-PDIP
RS-485/RS-422 differential line transceiver · 1 driver · 1 receiver · Full duplex · RS-485 and RS-422 · 5 Mbps · 5 V · ±200 mV

پەیوەندی بۆ نرخ

بینینی داتاشیت →

SP490CN-L

✅ جێگرەوەی ڕاستەوخۆ
MaxLinear
📦 8-PDIP
RS-485/RS-422 differential line transceiver · 1 driver · 1 receiver · 5 Mbps · 5 V · ±200 mV · Wide common-mode range · RS-485 and RS-422

پەیوەندی بۆ نرخ

بینینی داتاشیت →

LTC490

✅ جێگرەوەی ڕاستەوخۆ
📦 8-PDIP
Documented as pin compatible with SP490; supply-current, enable-polarity, common-mode, and exact PDIP suffix differences require verification.

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

SN75179

✅ جێگرەوەی ڕاستەوخۆ
📦 8-PDIP
Documented as pin compatible with SP490; exact data-rate, enable, fail-safe, and package-suffix differences must be checked against the original board.

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

SP490ECP-L تایبەتمەندییەکان

Product Type Full-duplex differential RS-485/RS-422 transceiver
Transmitter Count 1 transmitter
Receiver Count 1 receiver
Duplex Mode Full duplex
Supported Standards RS-485 and RS-422
Maximum Data Rate 10 Mbps
ڤۆڵتیەی دابینکردن 5 V
Typical Supply Current 0.9 mA
Receiver Input Sensitivity ±200 mV
Common-Mode Range Wide common-mode range; numerical limit not provided
مەودای پلەی گەرمیی کارکردن 0°C to 70°C
پاکێج 8-PDIP (0.300 inch, 7.62 mm pitch)
جۆری دامەزراندن Through Hole
Packaging Type Tube
Logic Technology Low-power BiCMOS
Maximum Devices per Bus 32 devices
ECCN EAR99

ڕێنمایی ڕێکخستنی پینی SP490ECP-L 8-pdip (0.300 inch, 7.62 mm pitch)

ڕێکخستنی پین بۆ SP490ECP-L (پاکێجی 8-pdip (0.300 inch, 7.62 mm pitch)). ژمارەدانی پین، فەنکشنەکان و نەخشەکانی پەیوەندی لە داتاشیتی بەرھەمھێنەردا پێناسە کراون. سەرنجی بدە بۆ شوێنپێی ورد و ڕێنمایییەکانی لەحیمکردن.

نەخشەی پینئاوتی پاکێجی 8-pdip (0.300 inch, 7.62 mm pitch) بۆ SP490ECP-L

هیچ داتای وردی پینئاوت بەردەست نییە بۆ SP490ECP-L.

سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.

بەکارهێنانە باوەکان

SP490ECP-L گونجاوە بۆ 6 بەکارھێنانs: Industrial RS-485 Control Bus, Point-to-Point RS-422 Data Link, Process Instrumentation Interface, Telecommunications Equipment, Data Acquisition System, Legacy Test and Measurement Interface.

🏭

Industrial RS-485 Control Bus

The SP490ECP-L fits legacy industrial control equipment that requires a low-power, full-duplex differential transceiver on a +5 V supply. Its one-transmitter, one-receiver arrangement supports separate RS-485 differential pairs, while the documented 10 Mbps capability provides ample bandwidth for command, status, and sensor traffic. The wide common-mode range is useful where the bus ground differs from the transceiver ground. In a deployed system, terminate the far ends of each differential pair, keep the signal and return conductors together, and verify grounding to reduce common-mode stress. Engineers should also account for obsolete-product risk when designing new production equipment.

🌐

Point-to-Point RS-422 Data Link

The SP490ECP-L is appropriate for a point-to-point RS-422 link when both ends can support separate differential transmit and receive pairs. The device provides one differential driver and one differential receiver, supports operation up to 10 Mbps, and uses +5 V-only supply operation. Full-duplex operation removes the need to pause reception while transmitting, which is beneficial for continuous monitoring or time-critical data exchange. Board integrators should verify the exact pin map, provide correct termination at the receiver, and route the differential pair to minimize conversion of common-mode noise into differential errors.

⚙️

Process Instrumentation Interface

The SP490ECP-L can connect legacy sensors, transmitters, or controllers that use differential RS-485 signaling. Its receiver sensitivity of ±200 mV supports detection of small differential signal levels, while the wide common-mode range helps operation in industrial environments where ground potentials can vary between equipment. The +5 V supply and typical 0.9 mA supply current are compatible with compact embedded interface boards. Practical implementation requires checking the receiver threshold, bus idle state, protection-network design, and isolation requirements. Because the target is obsolete, a new instrument platform should evaluate an active replacement instead of qualifying this suffix for long-term production.

🌐

Telecommunications Equipment

The SP490ECP-L is suitable for legacy telecommunications equipment that uses +5 V full-duplex RS-485 or RS-422 links for supervisory, configuration, or backplane communication. Its documented operation up to 10 Mbps supports moderately high-speed control traffic, and the differential interface reduces susceptibility to noise compared with a single-ended connection. In a backplane implementation, engineers should preserve controlled impedance, avoid long unprotected stubs, apply termination appropriate to the topology, and maintain a low-resistance ground reference. These practices help the receiver operate reliably across the wide common-mode range while minimizing differential signal degradation.

📟

Data Acquisition System

The SP490ECP-L can interface a data-acquisition controller to remote measurement modules over a full-duplex differential bus. One transmitter and one receiver provide independent outbound commands and inbound measurements, avoiding the turnaround delay associated with half-duplex communication. Its low-power BiCMOS implementation and typical 0.9 mA supply current suit compact multi-channel equipment, while 10 Mbps operation is substantially faster than required by many slow sensor protocols. Designers must still validate cable length, baud rate, termination, protection, and ground offsets for the actual installation because the supplied data does not specify a complete maximum cable-length matrix.

🖥️

Legacy Test and Measurement Interface

The SP490ECP-L can serve as the communications interface in older test and measurement instruments that exchange commands and results through a +5 V differential bus. The full-duplex arrangement supports simultaneous command transmission and result reception, while the 10 Mbps rate capability permits higher-speed transfer than many traditional serial-control protocols require. For reliable integration, keep transceiver routing short, terminate only the designated endpoints, and use a continuous ground reference where practical. Because the product is reported obsolete and several exact electrical limits are absent from the supplied excerpts, new instruments should use an actively supported part and perform a complete timing, noise, and thermal qualification.

کورتەی بەرهەمە پێشنیارکراوەکان

SP490E Same-family full-duplex RS-485/RS-422 transceiver family بەکارهێنراوە لە: Industrial RS-485 Control Bus, Telecommunications Equipment, Legacy Test and Measurement Interface LTC490 Documented pin-compatible SP490-family replacement بەکارهێنراوە لە: Industrial RS-485 Control Bus, Process Instrumentation Interface, Data Acquisition System SP490 Same-family SP490 transceiver family بەکارهێنراوە لە: Point-to-Point RS-422 Data Link SN75179 Documented pin-compatible SP490-family replacement بەکارهێنراوە لە: Point-to-Point RS-422 Data Link, Telecommunications Equipment, Legacy Test and Measurement Interface SP490ECP Closely related MaxLinear full-duplex transceiver ordering code بەکارهێنراوە لە: Process Instrumentation Interface, Data Acquisition System
What is the SP490ECP-L?
The SP490ECP-L is a +5 V, 10 Mbps, full-duplex RS-485/RS-422 transceiver from MaxLinear, Inc. It contains one differential transmitter and one differential receiver in an 8-PDIP package. According to the manufacturer product page, the SP490E family meets RS-485 and RS-422 standards up to 10 Mbps and provides ±200 mV receiver input sensitivity over a wide common-mode range.
Where can I download the SP490ECP-L datasheet PDF?
The official SP490ECP-L family documentation is available through the MaxLinear SP490E product page at https://www.maxlinear.com/product/interface/serial-transceivers/rs-485-rs-422/sp490e. The SP490ECP datasheet is also indexed by third-party document providers. Review the SP490E datasheet for the exact -L suffix ordering code, package drawing, electrical limits, and recommended external components before releasing a new design.
Where is the SP490ECP-L pinout located?
The SP490ECP-L pinout is defined in the manufacturer SP490E datasheet under the device pin-description and package-connection information. The verified listing confirms an 8-PDIP package, but the supplied search excerpts do not reproduce individual pin numbers or names. The exact pin map is therefore not asserted here; use the official datasheet and compare it with the board schematic before replacing the original component.
What are the key specifications of SP490ECP-L that engineers should know?
The key SP490ECP-L specifications are one transmitter, one receiver, full-duplex operation, RS-485 and RS-422 support, and a maximum data rate of 10 Mbps. According to the manufacturer product page, the device operates from +5 V, offers ±200 mV receiver sensitivity, and uses low-power BiCMOS. It is supplied in an 8-PDIP through-hole package and is specified over 0°C to 70°C.
Is the SP490ECP-L in stock?
Stock status for the SP490ECP-L is not reliably established by the supplied search excerpts. The DigiKey listing states that the part can be bought and shipped, while a GlobalSpec result identifies the product as obsolete. Because the target is obsolete and live distributor inventory can change rapidly, buyers should confirm stock, remaining supply, and the authorized-channel status at the time of purchase.
What is the price of SP490ECP-L as of 2026-10-28?
A defensible unit price for the SP490ECP-L as of 2026-10-28 is not present in the supplied verified data. The Octopart and distributor pages provide pricing and inventory tools, but the retrieved excerpts do not contain numeric price tiers. The placeholder zero-dollar values in this data record are not purchase quotations; request a current quote from XAIPART or an authorized distributor before budgeting the obsolete part.
What is the lead time for SP490ECP-L?
The verified excerpts do not state a numeric lead time for the obsolete SP490ECP-L. Lead time depends on remaining factory inventory, distributor stock, and whether the quantity is being consolidated from multiple authorized channels. Because the part is reported obsolete, confirm the current lead time and traceability with XAIPART rather than relying on historical distributor availability.
Where to buy SP490ECP-L online?
SP490ECP-L listings are available through Mouser, DigiKey, Octopart, and several electronic component marketplaces. The manufacturer and distributor links are listed in the data sources on this page. Since the product status is obsolete, the most reliable approach is to request an availability and traceability statement from XAIPART, particularly for production quantities that require date-code and lot-control records.
What can replace the SP490ECP-L?
The strongest documented replacements are the SP490ECP, SP490, and SP490E families from MaxLinear plus the pin-compatible LTC490 and SN75179 devices identified in the SP490 family documentation. Every candidate must be checked in the exact PDIP footprint and against enable logic, supply voltage, common-mode range, and termination requirements. The SP490E has separate driver and receiver enable functions while the SP491E adds explicit tri-state enable lines.
What is the best drop-in replacement for SP490ECP-L?
The SP490ECP is the most direct documented substitute because it identifies the same enhanced full-duplex RS-485 transceiver family in the same 8-pin PDIP configuration. The SP490E family page also confirms availability in 8-pin plastic DIP packages. Before treating any candidate as a drop-in replacement, verify the exact suffix, pin map, receiver fail-safe behavior, enable polarity, and operating-temperature requirements.
Is SP490ECP-L the same as LTC490?
The SP490 documentation identifies the SP490 family as pin compatible with the LTC490, but the two parts still require functional verification before substitution. According to the supplied SP490 family material, the SP490E is a full-duplex +5 V transceiver supporting RS-485 and RS-422 at up to 10 Mbps. Confirm the LTC490 package variant, pin assignment, enable functions, common-mode limits, and electrical characteristics against the original design.
SP490ECP-L vs SP490E: which is better?
SP490E is the better selection when an equivalent full-duplex RS-485/RS-422 transceiver family member is needed because the manufacturer directly lists the SP490E in 8-pin plastic DIP and NSOIC packages. The SP490ECP-L is the specific older ordering code reported as obsolete. Choose SP490E or another documented substitute only after confirming that its exact suffix preserves the required temperature grade, pinout, and lifecycle expectations.
Is the SP490ECP-L suitable for industrial RS-485 equipment?
The SP490ECP-L is technically suited to legacy industrial RS-485 links because it supports data rates up to 10 Mbps, uses differential signaling, and has a 0°C to 70°C rating. However, its obsolete lifecycle status and through-hole package limit new-design use. For new industrial equipment, choose an active interface transceiver with verified temperature, ESD, isolation, and lifecycle requirements.
What power and thermal considerations apply to SP490ECP-L?
The verified SP490E data specifies +5 V-only operation and a typical supply current of 0.9 mA. The supplied information does not include the complete maximum current, output-driver loading, or package thermal-resistance curves, so a complete worst-case dissipation calculation cannot be performed. Designers should include transceiver and termination dissipation while accounting for the shared 5 V supply, bus loading, and board-level temperature rise.
Is SP490ECP-L RoHS, REACH, or AEC-Q100 compliant?
The supplied verified excerpts do not identify the SP490ECP-L as RoHS compliant, REACH compliant, or AEC-Q100 qualified. Its GlobalSpec listing reports EAR99 export classification, but EAR99 is not an environmental or automotive qualification. Compliance and qualification documents should therefore be requested for the exact manufacturer lot before making a compliance claim.

داتای سەرچاوەی ئەندازیاری بۆ SP490ECP-L — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.

ڕێنمایی هەڵبژاردن

Choose the SP490ECP-L only when maintaining an existing legacy design where the exact manufacturer suffix, 8-PDIP footprint, and verified behavior are essential. It provides one transmitter and one receiver for full-duplex RS-485/RS-422 links, operates from +5 V, and supports rates up to 10 Mbps, but its reported obsolete status makes it unsuitable as an unqualified choice for new long-life production. Prefer SP490E when its exact ordering code and temperature grade satisfy the design. Consider SP490ECP for continuity with the documented full-duplex family. Use LTC490 or SN75179 only after comparing pin assignments, enable polarity, receiver thresholds, common-mode limits, fail-safe behavior, and package details. For new industrial or automotive products, choose an actively supported transceiver with complete environmental qualification instead of relying on this obsolete part.

بەراوردکردن لەگەڵ جێگرەوەکان

پارامەتر ئەم بەرهەمە SP490ECP SP490E SP490 LTC490 SN75179
Package 8-PDIP 8-PDIP 8-PDIP 8-PDIP 8-PDIP 8-PDIP
Brand MaxLinear, Inc. MaxLinear, Inc. MaxLinear, Inc. MaxLinear, Inc. Analog Devices Texas Instruments

جیاکەرەوە سەرەکییەکان

  • Direct manufacturer family continuity (بەراورد بەLTC490)
  • Documented +5 V low-power operation (بەراورد بەSN75179)
  • Full-duplex operation in a through-hole package (بەراورد بەSP490)

تێبینییەکانی دیزاین

Do not treat the SP490E and SP491E as interchangeable: the manufacturer states that SP491E is identical to SP490E except for the addition of driver and receiver tri-state enable lines. Confirm the original schematic, enable polarity, and whether the transceiver is intended for simultaneous full-duplex operation. For an existing SP490ECP-L board, verify the exact physical pin mapping and package suffix before ordering any listed alternative.

Route each differential pair as a tightly coupled pair over a continuous ground plane, minimize stubs to the transceiver, and keep the interface away from switching nodes and high-current paths. Terminate only the designated physical ends of the bus. The wide common-mode range does not remove the need for controlled grounding because excessive bus-to-ground voltage can still exceed the absolute maximum ratings specified by the manufacturer datasheet.

Use a stable +5 V rail and place local bypass capacitance close to the transceiver supply pin according to the manufacturer layout recommendation. The verified typical supply current is 0.9 mA, but total board demand also includes driver load, termination current, pull-up or fail-safe networks, and any external protection devices. Validate operation across the full source impedance, voltage tolerance, temperature range, and bus loading rather than relying on the typical supply-current value.

زانیاری پابەندبوون

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Qualified
بێ قوڕقوشم
Unknown
بێ ھالۆجین
Unknown
کانزا ناکۆکەکان
Unknown

The verified excerpts report EAR99 export classification but do not provide RoHS, REACH, lead-free, halogen-free, conflict-minerals, or AEC-Q100 documentation. AEC-Q100 is therefore recorded as not qualified because no qualification was found in the supplied data.

داتا پشتڕاستکراوەتەوە لە: 2026-10-28 — داتا لەلایەن تیمی ئەندازیاری پێکھاتەکانی XAIPART پشتڕاستکراوەتەوە و ڕێکخراوە

گەڕانە پەیوەندیدارەکان

SP490ECP-L SP490ECP-L datasheet PDF MaxLinear SP490ECP-L SP490ECP-L 10 Mbps RS-485 transceiver 8-PDIP full duplex RS-485 IC SP490ECP-L RS-422 interface SP490ECP-L vs SP490E SP490ECP-L drop-in replacement SP490ECP-L buy online SP490ECP-L price and stock What can replace SP490ECP-L? SP490ECP-L pinout

پێکهاتە و زاراوە پەیوەندیدارەکان

MaxLinear, Inc. SP490ECP-L SP490ECP SP490E SP490 SP491E LTC490 SN75179 RS-485 RS-422 full-duplex transceiver differential line driver differential line receiver BiCMOS interface IC 8-PDIP through-hole package receiver input sensitivity common-mode range maximum data rate industrial control bus process instrumentation data acquisition EAR99 obsolete lifecycle status
داواکاری نرخی خێرا RFQ
وردەکارییەکانی تەواو پڕ بکەرەوە — تیمی فرۆشتنی ئێمە لە ماوەی 24 کاتژمێردا وەڵام دەداتەوە
ژمارەی پارچە بەرهەمهێنەر پاکەت QTY نرخی ئامانج کۆی گشتی
✓
نرخەکە نێردرا!

لە ماوەی ٢٤ کاتژمێردا وەڵامی ئیمەیڵەکەت دەدەینەوە

1
داواکاری نرخ پێشکەشکرا
2
نرخپێدان وەرگیرا
3
داواکاری دانرا
4
پارەدان
5
نێردرا
6
گەیەنراوە
بینینی وردەکاریی داواکاری نرخ