ADS7842E - 12-Bit 4-Channel 200 kHz SAR ADC | Texas Instruments
MPN: ADS7842E ✓ چالاکADS7842E گشتی
An ADC is a data-conversion device that transforms an analog voltage into a numeric value for processing, measurement, or control. The ADS7842E belongs to the SAR ADC family, where a capacitor-based internal DAC successively approximates the input voltage. Within the broader hierarchy, it is a data-converter IC, an interface IC, and a semiconductor designed for data-acquisition and embedded measurement systems.
Key features include four analog inputs through a multiplexer, 12-bit resolution, a 200 kHz conversion rate, and ±1 LSB integral and differential nonlinearity. The converter also provides 72 dB signal-to-noise and distortion ratio and low power dissipation of 2 mW. These characteristics suit precision measurements where four analog signals must be digitized rapidly without employing a high-power switching converter.
Internally, the ADS7842E combines a four-channel analog multiplexer, 12-bit capacitor-based SAR converter, sample-and-hold amplifier, microprocessor interface, and parallel three-state output drivers. The tri-state outputs allow the device to share digital bus connections with other peripherals, reducing contention when the processor does not select the converter. The reference voltage is adjustable, supporting analog ranges selected by the system designer.
Typical applications include industrial data acquisition, test and measurement equipment, battery-powered instrumentation, and process-control systems. The four-channel input structure reduces the need for multiple converters when several slowly changing sensors must share one digital interface. The 200 kHz sampling capability also supports higher-rate sampled measurements when settling and signal-conditioning requirements are satisfied.
The primary design consideration is analog signal conditioning. Inputs must remain within the converter's specified operating range, and the reference, supply, and bypass connections require careful layout. A quiet reference and short analog traces are especially important because gain, noise, and conversion accuracy depend on the complete analog signal chain rather than on resolution alone.
This page combines manufacturer specifications, practical application guidance, interface considerations, and structured comparisons with compatible Texas Instruments ordering variants. These engineering details help distinguish the ADS7842E from related converter families and simplify footprint and procurement planning.
جێگرەوەکانی جێگۆڕکێ بۆ ADS7842E — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ ADS7842E (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Differential Nonlinearity, Digital Interface, Integral Nonlinearity, Operating Temperature Range, Power Dissipation.
ADS7842E/1KG4
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →ADS7842EG4
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
ADS7842EB
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →ADS7842E/1KG4
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →ADS7842E/1K.B
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
ADS7842E زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان
| وردی | 12 bit |
| Analog Input Channels | 4 channels |
| Converter Architecture | 1 successive-approximation-register (SAR) converter |
| ڕێژەی نموونەگرتن | 200 kHz |
| Supply Voltage Range | 2.7 V to 5 V |
| Power Dissipation | 2 mW |
| Integral Nonlinearity | ±1 LSB |
| Differential Nonlinearity | ±1 LSB |
| Signal-to-Noise and Distortion Ratio | 72 dB |
| Digital Interface | 12-bit parallel microprocessor interface with 3-state outputs |
| Input Multiplexer | 4-to-1 analog multiplexer |
| Sample-and-Hold | 1 integrated sample-and-hold amplifier |
| پاکێج | 28-pin SSOP (DB) |
| مەودای پلەی گەرمیی کارکردن | -40 °C to +85 °C |
ڕێنمایی ڕێکخستنی پینی ADS7842E 28-pin ssop (db)
ڕێکخستنی پین بۆ ADS7842E (پاکێجی 28-pin ssop (db)). ئەم پێکھاتە ئەنالۆگە پینی چوونەژوورەوە، دەرچوون و دابینکردنی وزەی ھەیە. سەرنج بدە بە داتاشیتی بەرھەمھێنەر بۆ ڕێکخستنەکانی پینی لادانی ئۆفسێت، قەرەبووکردنەوە و چالاککردن. گونجاوە بۆ ڕێکخستنی ئیشارەت و خولەکانی بەرزکەرەوە.
هیچ داتای وردی پینئاوت بەردەست نییە بۆ ADS7842E.
سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.
بەکارهێنانە باوەکان
ADS7842E گونجاوە بۆ 6 بەکارھێنانs: Industrial Process Data Acquisition, Test and Measurement Equipment, Battery-Powered Portable Instruments, Programmable Control and Monitoring, Condition Monitoring and Diagnostics, Communication and Sensor Interface Cards.
Industrial Process Data Acquisition
The ADS7842E suits industrial measurement systems that monitor four analog sensor channels through one parallel ADC. Its 4-to-1 analog multiplexer reduces component count, while 12-bit resolution provides 4096 discrete code levels for process control. Operating from 2.7 V to 5 V and dissipating 2 mW supports compact 3.3 V or 5 V instrumentation. Place the converter behind appropriate input protection and conditioning, and use the parallel interface only where the host bus can accommodate 12 data lines.
پێشنیارکراو
Test and Measurement Equipment
The ADS7842E can digitize up to four measured quantities at a 200 kHz sampling rate, making it appropriate for automated test systems, signal monitors, and laboratory instruments. Its ±1 LSB INL and DNL figures support repeatable measurements, while 72 dB SINAD provides a useful noise metric for the complete analog path. The 28-pin SSOP package permits a compact layout, although the parallel bus requires careful routing and the reference network must remain quiet.
پێشنیارکراو
Battery-Powered Portable Instruments
The 2 mW power dissipation and 2.7 V to 5 V single-supply operation of the ADS7842E are useful in handheld meters and portable diagnostic equipment. Four analog inputs can share a converter when sensors change at a moderate rate, reducing both board area and power demand. The 200 kHz capability supports faster sampled measurements, but designers should account for acquisition time and reference current. Use a low-noise reference and place bypass components close to the supply and reference pins.
پێشنیارکراو
Programmable Control and Monitoring
The ADS7842E provides a direct parallel interface for microprocessors that monitor pressure, position, temperature, or current sensors in a programmable controller. Its three-state output drivers can place the converter on a shared digital bus when the host controls chip selection, reducing the number of separate bus interfaces. A 200 kHz conversion rate is suitable for multi-channel supervisory sampling. Firmware should account for channel selection, acquisition timing, and the tri-state enable behavior used by the host.
پێشنیارکراو
Condition Monitoring and Diagnostics
A condition-monitoring controller can use the ADS7842E to sample several diagnostic channels, including vibration proxies, supply levels, and sensor outputs. The four-channel multiplexer permits sequential acquisition without four separate converters, and the 12-bit resolution is adequate for many threshold and trend measurements. The 200 kHz sampling rate offers margin above slow supervisory sampling rates. For high-frequency diagnostic signals, verify input bandwidth, acquisition time, and source impedance before relying on the headline conversion rate.
پێشنیارکراو
Communication and Sensor Interface Cards
The ADS7842E is suitable for peripheral cards that acquire four analog inputs and transfer the resulting 12-bit values to a host processor. Its microprocessor-oriented parallel interface is efficient when the card backplane already provides a parallel bus, and its 200 kHz conversion rate supports moderate-rate sampling. The 28-pin SSOP package keeps the converter compact, but routing 12 data lines plus control signals may require careful layer planning. Use the manufacturer pin-description table to preserve bus direction and chip-select behavior.
پێشنیارکراو
کورتەی بەرهەمە پێشنیارکراوەکان
داتای سەرچاوەی ئەندازیاری بۆ ADS7842E — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | ADS7842E/1K | ADS7842EG4 | ADS7842EB | ADS7842E/1KG4 | ADS7842E/1K.B |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 28-pin SSOP (DB) | 28-pin SSOP (DB) - same | 28-pin SSOP (DB) - same | 28-pin SSOP (DB) - same | 28-pin SSOP (DB) - same | 28-pin SSOP (DB) - same |
| Resolution | 12 bit | 12 bit | 12 bit | 12 bit | 12 bit | 12 bit |
| Analog Input Channels | 4 channels | 4 channels | 4 channels | 4 channels | 4 channels | 4 channels |
| Sampling Rate | 200 kHz | 200 kHz | 200 kHz | 200 kHz | 200 kHz | 200 kHz |
| Supply Voltage Range | 2.7 V to 5 V | 2.7 V to 5 V | 2.7 V to 5 V | 2.7 V to 5 V | 2.7 V to 5 V | 2.7 V to 5 V |
| Converter Architecture | SAR with capacitor-based internal DAC | SAR with capacitor-based internal DAC | SAR with capacitor-based internal DAC | SAR with capacitor-based internal DAC | SAR with capacitor-based internal DAC | SAR with capacitor-based internal DAC |
| Digital Interface | 12-bit parallel with 3-state outputs | 12-bit parallel with 3-state outputs | 12-bit parallel with 3-state outputs | 12-bit parallel with 3-state outputs | 12-bit parallel with 3-state outputs | 12-bit parallel with 3-state outputs |
| Integral Nonlinearity | ±1 LSB | ±1 LSB | ±1 LSB | ±1 LSB | ±1 LSB | ±1 LSB |
| Differential Nonlinearity | ±1 LSB | ±1 LSB | ±1 LSB | ±1 LSB | ±1 LSB | ±1 LSB |
| Power Dissipation | 2 mW | 2 mW | 2 mW | 2 mW | 2 mW | 2 mW |
جیاکەرەوە سەرەکییەکان
- Four-channel integration in one parallel-interface converter (بەراورد بەADS7842E/1K)
- Consistent 200 kHz SAR performance across family orderings (بەراورد بەADS7842EG4)
- Direct microprocessor connection through parallel three-state outputs (بەراورد بەADS7842EB)
تێبینییەکانی دیزاین
Route the analog inputs directly to the multiplexer pins and keep them away from clock, bus, and switching-regulator traces. The four-channel input architecture does not remove the need for channel isolation: place input filtering close to the source when long cables, high-impedance sensors, or adjacent switching nodes could otherwise introduce errors. Maintain a continuous ground reference beneath and around the analog section.
Decouple the 2.7 V to 5 V supply at the converter using the component and capacitance recommendations in the Texas Instruments ADS7842 datasheet. Keep the placement path short and return the capacitor ground directly to the device ground plane. Reference-noise and supply-impedance effects can degrade the specified 72 dB SINAD even when the converter itself operates within its stated limits.
Treat the 12 parallel output lines as a grouped synchronous bus with matched routing practices. Establish the host interface for the three-state outputs so the ADS7842E cannot contend with another peripheral on shared data lines. Account for setup and hold timing, output enable behavior, and acquisition timing in firmware; the 200 kHz headline rate is not a substitute for the complete conversion timing shown in the datasheet.
Do not assume that every ADS7842 family suffix has identical qualification, temperature, or shipping attributes. Verify the exact orderable number, package marking, reel or tube configuration, and production requirements. For a drop-in substitution, confirm that the replacement retains the 28-pin SSOP footprint, 4-channel multiplexing, 12-bit parallel interface, supply range, and timing requirements.
زانیاری پابەندبوون
No explicit RoHS, REACH, lead-free, halogen-free, or conflict-minerals status was identified for the exact ADS7842E orderable number. Automotive qualification status is not claimed.